From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- Documentation/devicetree/bindings/serial/8250.yaml | 259 +++++++++++++++++++++ .../devicetree/bindings/serial/8250_omap.yaml | 120 ++++++++++ .../bindings/serial/actions,owl-uart.txt | 16 ++ .../devicetree/bindings/serial/altera_jtaguart.txt | 5 + .../devicetree/bindings/serial/altera_uart.txt | 8 + .../bindings/serial/amlogic,meson-uart.yaml | 82 +++++++ .../devicetree/bindings/serial/arc-uart.txt | 25 ++ .../devicetree/bindings/serial/arm,mps2-uart.txt | 19 ++ .../devicetree/bindings/serial/arm_sbsa_uart.txt | 10 + .../bindings/serial/atmel,at91-usart.yaml | 190 +++++++++++++++ .../bindings/serial/brcm,bcm2835-aux-uart.txt | 18 ++ .../bindings/serial/brcm,bcm6345-uart.yaml | 47 ++++ .../bindings/serial/brcm,bcm7271-uart.yaml | 95 ++++++++ .../devicetree/bindings/serial/cavium-uart.txt | 19 ++ .../devicetree/bindings/serial/cdns,uart.yaml | 66 ++++++ .../bindings/serial/cirrus,clps711x-uart.txt | 31 +++ .../devicetree/bindings/serial/digicolor-usart.txt | 27 +++ .../bindings/serial/fsl,s32-linflexuart.yaml | 48 ++++ .../devicetree/bindings/serial/fsl-imx-uart.yaml | 112 +++++++++ .../devicetree/bindings/serial/fsl-lpuart.yaml | 88 +++++++ .../devicetree/bindings/serial/fsl-mxs-auart.yaml | 91 ++++++++ .../devicetree/bindings/serial/ingenic,uart.yaml | 99 ++++++++ .../devicetree/bindings/serial/lantiq_asc.txt | 31 +++ .../devicetree/bindings/serial/litex,liteuart.yaml | 40 ++++ .../devicetree/bindings/serial/maxim,max310x.txt | 48 ++++ .../devicetree/bindings/serial/mediatek,uart.yaml | 121 ++++++++++ .../bindings/serial/microchip,pic32-uart.txt | 29 +++ .../devicetree/bindings/serial/milbeaut-uart.txt | 21 ++ .../devicetree/bindings/serial/mrvl,pxa-ssp.txt | 64 +++++ .../devicetree/bindings/serial/mvebu-uart.txt | 56 +++++ .../bindings/serial/nvidia,tegra194-tcu.yaml | 61 +++++ .../bindings/serial/nvidia,tegra20-hsuart.txt | 73 ++++++ .../bindings/serial/nxp,lpc1850-uart.txt | 28 +++ .../devicetree/bindings/serial/nxp,sc16is7xx.txt | 118 ++++++++++ .../bindings/serial/nxp-lpc32xx-hsuart.txt | 14 ++ .../devicetree/bindings/serial/pl011.yaml | 126 ++++++++++ .../bindings/serial/qca,ar9330-uart.yaml | 50 ++++ .../devicetree/bindings/serial/qcom,msm-uart.txt | 25 ++ .../bindings/serial/qcom,msm-uartdm.yaml | 112 +++++++++ .../bindings/serial/qcom,serial-geni-qcom.yaml | 86 +++++++ .../bindings/serial/rda,8810pl-uart.yaml | 46 ++++ .../bindings/serial/renesas,em-uart.yaml | 74 ++++++ .../devicetree/bindings/serial/renesas,hscif.yaml | 150 ++++++++++++ .../devicetree/bindings/serial/renesas,sci.yaml | 109 +++++++++ .../devicetree/bindings/serial/renesas,scif.yaml | 197 ++++++++++++++++ .../devicetree/bindings/serial/renesas,scifa.yaml | 112 +++++++++ .../devicetree/bindings/serial/renesas,scifb.yaml | 103 ++++++++ Documentation/devicetree/bindings/serial/rs485.txt | 1 + .../devicetree/bindings/serial/rs485.yaml | 56 +++++ .../devicetree/bindings/serial/samsung_uart.yaml | 145 ++++++++++++ .../devicetree/bindings/serial/serial.yaml | 153 ++++++++++++ .../devicetree/bindings/serial/sifive-serial.yaml | 65 ++++++ .../bindings/serial/snps-dw-apb-uart.yaml | 153 ++++++++++++ .../bindings/serial/socionext,uniphier-uart.yaml | 51 ++++ .../devicetree/bindings/serial/sprd-uart.yaml | 75 ++++++ .../devicetree/bindings/serial/st,stm32-uart.yaml | 133 +++++++++++ .../devicetree/bindings/serial/st-asc.txt | 18 ++ .../bindings/serial/sunplus,sp7021-uart.yaml | 56 +++++ .../devicetree/bindings/serial/vt8500-uart.txt | 27 +++ .../bindings/serial/xlnx,opb-uartlite.yaml | 89 +++++++ 60 files changed, 4391 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/8250.yaml create mode 100644 Documentation/devicetree/bindings/serial/8250_omap.yaml create mode 100644 Documentation/devicetree/bindings/serial/actions,owl-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/altera_jtaguart.txt create mode 100644 Documentation/devicetree/bindings/serial/altera_uart.txt create mode 100644 Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/arc-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/arm,mps2-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt create mode 100644 Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml create mode 100644 Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/brcm,bcm7271-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/cavium-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/cdns,uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/digicolor-usart.txt create mode 100644 Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml create mode 100644 Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/fsl-lpuart.yaml create mode 100644 Documentation/devicetree/bindings/serial/fsl-mxs-auart.yaml create mode 100644 Documentation/devicetree/bindings/serial/ingenic,uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/lantiq_asc.txt create mode 100644 Documentation/devicetree/bindings/serial/litex,liteuart.yaml create mode 100644 Documentation/devicetree/bindings/serial/maxim,max310x.txt create mode 100644 Documentation/devicetree/bindings/serial/mediatek,uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/milbeaut-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/mrvl,pxa-ssp.txt create mode 100644 Documentation/devicetree/bindings/serial/mvebu-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.yaml create mode 100644 Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt create mode 100644 Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt create mode 100644 Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt create mode 100644 Documentation/devicetree/bindings/serial/pl011.yaml create mode 100644 Documentation/devicetree/bindings/serial/qca,ar9330-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml create mode 100644 Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml create mode 100644 Documentation/devicetree/bindings/serial/rda,8810pl-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,em-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,hscif.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,sci.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,scif.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,scifa.yaml create mode 100644 Documentation/devicetree/bindings/serial/renesas,scifb.yaml create mode 100644 Documentation/devicetree/bindings/serial/rs485.txt create mode 100644 Documentation/devicetree/bindings/serial/rs485.yaml create mode 100644 Documentation/devicetree/bindings/serial/samsung_uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/serial.yaml create mode 100644 Documentation/devicetree/bindings/serial/sifive-serial.yaml create mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/sprd-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/st,stm32-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/st-asc.txt create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml create mode 100644 Documentation/devicetree/bindings/serial/vt8500-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml (limited to 'Documentation/devicetree/bindings/serial') diff --git a/Documentation/devicetree/bindings/serial/8250.yaml b/Documentation/devicetree/bindings/serial/8250.yaml new file mode 100644 index 000000000..6258f5f59 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/8250.yaml @@ -0,0 +1,259 @@ +# Copyright 2020 Lubomir Rintel +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/8250.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UART (Universal Asynchronous Receiver/Transmitter) bindings + +maintainers: + - devicetree@vger.kernel.org + +allOf: + - $ref: serial.yaml# + - if: + anyOf: + - required: + - aspeed,lpc-io-reg + - required: + - aspeed,lpc-interrupts + - required: + - aspeed,sirq-polarity-sense + then: + properties: + compatible: + const: aspeed,ast2500-vuart + - if: + properties: + compatible: + const: mrvl,mmp-uart + then: + properties: + reg-shift: + const: 2 + required: + - reg-shift + - if: + not: + properties: + compatible: + items: + - enum: + - ns8250 + - ns16450 + - ns16550 + - ns16550a + then: + anyOf: + - required: [ clock-frequency ] + - required: [ clocks ] + +properties: + compatible: + oneOf: + - const: ns8250 + - const: ns16450 + - const: ns16550 + - const: ns16550a + - const: ns16850 + - const: aspeed,ast2400-vuart + - const: aspeed,ast2500-vuart + - const: intel,xscale-uart + - const: mrvl,pxa-uart + - const: nuvoton,wpcm450-uart + - const: nuvoton,npcm750-uart + - const: nuvoton,npcm845-uart + - const: nvidia,tegra20-uart + - const: nxp,lpc3220-uart + - items: + - enum: + - exar,xr16l2552 + - exar,xr16l2551 + - exar,xr16l2550 + - const: ns8250 + - items: + - enum: + - altr,16550-FIFO32 + - altr,16550-FIFO64 + - altr,16550-FIFO128 + - fsl,16550-FIFO64 + - fsl,ns16550 + - andestech,uart16550 + - nxp,lpc1850-uart + - opencores,uart16550-rtlsvn105 + - ti,da830-uart + - const: ns16550a + - items: + - enum: + - ns16750 + - cavium,octeon-3860-uart + - xlnx,xps-uart16550-2.00.b + - ralink,rt2880-uart + - enum: + - ns16550 # Deprecated, unless the FIFO really is broken + - ns16550a + - items: + - enum: + - ralink,mt7620a-uart + - ralink,rt3052-uart + - ralink,rt3883-uart + - const: ralink,rt2880-uart + - enum: + - ns16550 # Deprecated, unless the FIFO really is broken + - ns16550a + - items: + - enum: + - mediatek,mt7622-btif + - mediatek,mt7623-btif + - const: mediatek,mtk-btif + - items: + - const: mrvl,mmp-uart + - const: intel,xscale-uart + - items: + - enum: + - nvidia,tegra30-uart + - nvidia,tegra114-uart + - nvidia,tegra124-uart + - nvidia,tegra210-uart + - nvidia,tegra186-uart + - nvidia,tegra194-uart + - nvidia,tegra234-uart + - const: nvidia,tegra20-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: true + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + current-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The current active speed of the UART. + + reg-offset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Offset to apply to the mapbase from the start of the registers. + + reg-shift: + description: Quantity to shift the register offsets by. + + reg-io-width: + description: | + The size (in bytes) of the IO accesses that should be performed on the + device. There are some systems that require 32-bit accesses to the + UART (e.g. TI davinci). + + used-by-rtas: + type: boolean + description: | + Set to indicate that the port is in use by the OpenFirmware RTAS and + should not be registered. + + no-loopback-test: + type: boolean + description: | + Set to indicate that the port does not implement loopback test mode. + + fifo-size: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The fifo size of the UART. + + auto-flow-control: + type: boolean + description: | + One way to enable automatic flow control support. The driver is + allowed to detect support for the capability even without this + property. + + tx-threshold: + description: | + Specify the TX FIFO low water indication for parts with programmable + TX FIFO thresholds. + + overrun-throttle-ms: + description: | + How long to pause uart rx when input overrun is encountered. + + rts-gpios: true + cts-gpios: true + dtr-gpios: true + dsr-gpios: true + rng-gpios: true + dcd-gpios: true + + aspeed,sirq-polarity-sense: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: | + Phandle to aspeed,ast2500-scu compatible syscon alongside register + offset and bit number to identify how the SIRQ polarity should be + configured. One possible data source is the LPC/eSPI mode bit. Only + applicable to aspeed,ast2500-vuart. + deprecated: true + + aspeed,lpc-io-reg: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: | + The VUART LPC address. Only applicable to aspeed,ast2500-vuart. + + aspeed,lpc-interrupts: + $ref: "/schemas/types.yaml#/definitions/uint32-array" + minItems: 2 + maxItems: 2 + description: | + A 2-cell property describing the VUART SIRQ number and SIRQ + polarity (IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_LEVEL_HIGH). Only + applicable to aspeed,ast2500-vuart. + +required: + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + serial@80230000 { + compatible = "ns8250"; + reg = <0x80230000 0x100>; + interrupts = <10>; + reg-shift = <2>; + clock-frequency = <48000000>; + }; + - | + #include + serial@49042000 { + compatible = "andestech,uart16550", "ns16550a"; + reg = <0x49042000 0x400>; + interrupts = <80>; + clock-frequency = <48000000>; + cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + - | + #include + #include + serial@1e787000 { + compatible = "aspeed,ast2500-vuart"; + reg = <0x1e787000 0x40>; + reg-shift = <2>; + interrupts = <8>; + clocks = <&syscon ASPEED_CLK_APB>; + no-loopback-test; + aspeed,lpc-io-reg = <0x3f8>; + aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/8250_omap.yaml b/Documentation/devicetree/bindings/serial/8250_omap.yaml new file mode 100644 index 000000000..7b34ec8fa --- /dev/null +++ b/Documentation/devicetree/bindings/serial/8250_omap.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/8250_omap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for 8250 compliant UARTs on TI's OMAP2+ and K3 SoCs + +maintainers: + - Vignesh Raghavendra + +allOf: + - $ref: /schemas/serial/serial.yaml# + - $ref: /schemas/serial/rs485.yaml# + +properties: + compatible: + oneOf: + - enum: + - ti,am3352-uart + - ti,am4372-uart + - ti,am654-uart + - ti,dra742-uart + - ti,omap2-uart + - ti,omap3-uart + - ti,omap4-uart + - items: + - enum: + - ti,am64-uart + - ti,j721e-uart + - const: ti,am654-uart + + ti,hwmods: + description: + Must be "uart", n being the instance number (1-based) + This property is applicable only on legacy platforms mainly omap2/3 + and ti81xx and should not be used on other platforms. + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + items: + - const: tx + - const: rx + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + description: + First entry is module IRQ required for normal IO operation. + Second entry is optional and corresponds to system wakeup IRQ + where supported. + + clocks: + maxItems: 1 + + clock-names: + const: fclk + + rts-gpios: true + cts-gpios: true + dtr-gpios: true + dsr-gpios: true + rng-gpios: true + dcd-gpios: true + rs485-rts-delay: true + rs485-rts-active-low: true + rs485-rx-during-tx: true + rs485-rts-active-high: true + linux,rs485-enabled-at-boot-time: true + rts-gpio: true + power-domains: true + clock-frequency: true + current-speed: true + overrun-throttle-ms: true + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +if: + properties: + compatible: + contains: + enum: + - ti,omap2-uart + - ti,omap3-uart + - ti,omap4-uart + +then: + properties: + ti,hwmods: + items: + - pattern: "^uart([1-9])$" + +else: + properties: + ti,hwmods: false + +examples: + - | + serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + }; diff --git a/Documentation/devicetree/bindings/serial/actions,owl-uart.txt b/Documentation/devicetree/bindings/serial/actions,owl-uart.txt new file mode 100644 index 000000000..aa873eada --- /dev/null +++ b/Documentation/devicetree/bindings/serial/actions,owl-uart.txt @@ -0,0 +1,16 @@ +Actions Semi Owl UART + +Required properties: +- compatible : "actions,s500-uart", "actions,owl-uart" for S500 + "actions,s900-uart", "actions,owl-uart" for S900 +- reg : Offset and length of the register set for the device. +- interrupts : Should contain UART interrupt. + + +Example: + + uart3: serial@b0126000 { + compatible = "actions,s500-uart", "actions,owl-uart"; + reg = <0xb0126000 0x1000>; + interrupts = ; + }; diff --git a/Documentation/devicetree/bindings/serial/altera_jtaguart.txt b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt new file mode 100644 index 000000000..55a901051 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt @@ -0,0 +1,5 @@ +Altera JTAG UART + +Required properties: +- compatible : should be "ALTR,juart-1.0" +- compatible : should be "altr,juart-1.0" diff --git a/Documentation/devicetree/bindings/serial/altera_uart.txt b/Documentation/devicetree/bindings/serial/altera_uart.txt new file mode 100644 index 000000000..81bf7ffb1 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_uart.txt @@ -0,0 +1,8 @@ +Altera UART + +Required properties: +- compatible : should be "ALTR,uart-1.0" +- compatible : should be "altr,uart-1.0" + +Optional properties: +- clock-frequency : frequency of the clock input to the UART diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml new file mode 100644 index 000000000..7822705ad --- /dev/null +++ b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/amlogic,meson-uart.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson SoC UART Serial Interface + +maintainers: + - Neil Armstrong + +description: | + The Amlogic Meson SoC UART Serial Interface is present on a large range + of SoCs, and can be present either in the "Always-On" power domain or the + "Everything-Else" power domain. + + The particularity of the "Always-On" Serial Interface is that the hardware + is active since power-on and does not need any clock gating and is usable + as very early serial console. + +properties: + compatible: + oneOf: + - description: Always-on power domain UART controller + items: + - enum: + - amlogic,meson6-uart + - amlogic,meson8-uart + - amlogic,meson8b-uart + - amlogic,meson-gx-uart + - amlogic,meson-s4-uart + - const: amlogic,meson-ao-uart + - description: Everything-Else power domain UART controller + enum: + - amlogic,meson6-uart + - amlogic,meson8-uart + - amlogic,meson8b-uart + - amlogic,meson-gx-uart + - amlogic,meson-s4-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: external xtal clock identifier + - description: the bus core clock, either the clk81 clock or the gate clock + - description: the source of the baudrate generator, can be either the xtal or the pclk + + clock-names: + items: + - const: xtal + - const: pclk + - const: baud + + fifo-size: + description: The fifo size supported by the UART channel. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [64, 128] + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + serial@84c0 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x84c0 0x14>; + interrupts = <26>; + clocks = <&xtal>, <&pclk>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + }; diff --git a/Documentation/devicetree/bindings/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt new file mode 100644 index 000000000..256cc150c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arc-uart.txt @@ -0,0 +1,25 @@ +* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards + +Required properties: +- compatible : "snps,arc-uart" +- reg : offset and length of the register set for the device. +- interrupts : device interrupt +- clock-frequency : the input clock frequency for the UART +- current-speed : baud rate for UART + +e.g. + +arcuart0: serial@c0fc1000 { + compatible = "snps,arc-uart"; + reg = <0xc0fc1000 0x100>; + interrupts = <5>; + clock-frequency = <80000000>; + current-speed = <115200>; +}; + +Note: Each port should have an alias correctly numbered in "aliases" node. + +e.g. +aliases { + serial0 = &arcuart0; +}; diff --git a/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt new file mode 100644 index 000000000..128cc6aed --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt @@ -0,0 +1,19 @@ +ARM MPS2 UART + +Required properties: +- compatible : Should be "arm,mps2-uart" +- reg : Address and length of the register set +- interrupts : Reference to the UART RX, TX and overrun interrupts + +Required clocking property: +- clocks : The input clock of the UART + + +Examples: + +uart0: serial@40004000 { + compatible = "arm,mps2-uart"; + reg = <0x40004000 0x1000>; + interrupts = <0 1 12>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt new file mode 100644 index 000000000..4163e7eb7 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt @@ -0,0 +1,10 @@ +* ARM SBSA defined generic UART +This UART uses a subset of the PL011 registers and consequently lives +in the PL011 driver. It's baudrate and other communication parameters +cannot be adjusted at runtime, so it lacks a clock specifier here. + +Required properties: +- compatible: must be "arm,sbsa-uart" +- reg: exactly one register range +- interrupts: exactly one interrupt specifier +- current-speed: the (fixed) baud rate set by the firmware diff --git a/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml new file mode 100644 index 000000000..30b2131b5 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2022 Microchip Technology, Inc. and its subsidiaries +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/atmel,at91-usart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +maintainers: + - Richard Genoud + +properties: + compatible: + oneOf: + - enum: + - atmel,at91rm9200-usart + - atmel,at91sam9260-usart + - microchip,sam9x60-usart + - items: + - const: atmel,at91rm9200-dbgu + - const: atmel,at91rm9200-usart + - items: + - const: atmel,at91sam9260-dbgu + - const: atmel,at91sam9260-usart + - items: + - const: microchip,sam9x60-dbgu + - const: microchip,sam9x60-usart + - const: atmel,at91sam9260-dbgu + - const: atmel,at91sam9260-usart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-names: + minItems: 1 + items: + - const: usart + - const: gclk + + clocks: + minItems: 1 + items: + - description: USART Peripheral Clock + - description: USART Generic Clock + + dmas: + items: + - description: TX DMA Channel + - description: RX DMA Channel + + dma-names: + items: + - const: tx + - const: rx + + atmel,usart-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must be either for SPI or + for USART (found in dt-bindings/mfd/at91-usart.h). + enum: [ 0, 1 ] + + atmel,use-dma-rx: + type: boolean + description: use of PDC or DMA for receiving data + + atmel,use-dma-tx: + type: boolean + description: use of PDC or DMA for transmitting data + + atmel,fifo-size: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum number of data the RX and TX FIFOs can store for FIFO + capable USARTS. + enum: [ 16, 32 ] + +required: + - compatible + - reg + - interrupts + - clock-names + - clocks + - atmel,usart-mode + +allOf: + - if: + properties: + atmel,usart-mode: + const: 1 + then: + allOf: + - $ref: /schemas/spi/spi-controller.yaml# + + properties: + atmel,use-dma-rx: false + + atmel,use-dma-tx: false + + atmel,fifo-size: false + + "#size-cells": + const: 0 + + "#address-cells": + const: 1 + + required: + - "#size-cells" + - "#address-cells" + + else: + allOf: + - $ref: /schemas/serial/serial.yaml# + - $ref: /schemas/serial/rs485.yaml# + +unevaluatedProperties: false + +examples: + - | + #include + #include + #include + #include + + /* use PDC */ + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + atmel,usart-mode = ; + interrupts = <7>; + clocks = <&usart0_clk>; + clock-names = "usart"; + atmel,use-dma-rx; + atmel,use-dma-tx; + rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>; + }; + + - | + #include + #include + #include + #include + + /* use DMA */ + usart1: serial@f001c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf001c000 0x100>; + atmel,usart-mode = ; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&usart0_clk>; + clock-names = "usart"; + atmel,use-dma-rx; + atmel,use-dma-tx; + dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, + <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + }; + + - | + #include + #include + #include + #include + + /* SPI mode */ + spi0: spi@f001c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf001c000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + atmel,usart-mode = ; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&usart0_clk>; + clock-names = "usart"; + dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, + <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; + dma-names = "tx", "rx"; + cs-gpios = <&pioB 3 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt new file mode 100644 index 000000000..b5cc6297c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt @@ -0,0 +1,18 @@ +* BCM2835 AUXILIAR UART + +Required properties: + +- compatible: "brcm,bcm2835-aux-uart" +- reg: The base address of the UART register bank. +- interrupts: A single interrupt specifier. +- clocks: Clock driving the hardware; used to figure out the baud rate + divisor. + +Example: + + uart1: serial@7e215040 { + compatible = "brcm,bcm2835-aux-uart"; + reg = <0x7e215040 0x40>; + interrupts = <1 29>; + clocks = <&aux BCM2835_AUX_CLOCK_UART>; + }; diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.yaml b/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.yaml new file mode 100644 index 000000000..a22285c43 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/brcm,bcm6345-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: BCM63xx UART + +maintainers: + - Rafał Miłecki + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + const: brcm,bcm6345-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: refclk + +unevaluatedProperties: false + +required: + - reg + - interrupts + - clocks + +examples: + - | + serial@14e00520 { + compatible = "brcm,bcm6345-uart"; + reg = <0x14e00520 0x18>; + interrupt-parent = <&periph_intc>; + interrupts = <2>; + clocks = <&periph_clk>; + clock-names = "refclk"; + }; diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm7271-uart.yaml b/Documentation/devicetree/bindings/serial/brcm,bcm7271-uart.yaml new file mode 100644 index 000000000..6d176588d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/brcm,bcm7271-uart.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/brcm,bcm7271-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom 8250 based serial port devicetree bindings + +maintainers: + - Al Cooper + +allOf: + - $ref: serial.yaml# + +description: |+ + The Broadcom UART is based on the basic 8250 UART but with + enhancements for more accurate high speed baud rates and support + for DMA. + +properties: + compatible: + items: + - enum: + - brcm,bcm7271-uart + - brcm,bcm7278-uart + + reg: + minItems: 1 + maxItems: 5 + + reg-names: + description: The UART register block and optionally the DMA register blocks. + oneOf: + - items: + - const: uart + - items: + - const: uart + - const: dma_arb + - const: dma_rx + - const: dma_tx + - const: dma_intr2 + + clocks: + minItems: 1 + + clock-names: + const: sw_baud + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + description: The UART interrupt and optionally the DMA interrupt. + minItems: 1 + items: + - const: uart + - const: dma + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + +unevaluatedProperties: false + +examples: + - | + serial@840d000 { + compatible = "brcm,bcm7271-uart"; + reg = <0x840d000 0x20>; + reg-names = "uart"; + interrupts = <0x0 0x62 0x4>; + interrupt-names = "uart"; + clocks = <&scmi_clk 190>; + clock-names = "sw_baud"; + }; + + serial@840e000 { + compatible = "brcm,bcm7271-uart"; + reg = <0x840e000 0x20>, + <0x840e080 0x8>, + <0x840e100 0xa8>, + <0x840e200 0x4c>, + <0x840e300 0x30>; + reg-names = "uart", "dma_arb", "dma_rx", "dma_tx", "dma_intr2"; + interrupts = <0x0 0x62 0x4>, <0x0 0x75 0x4>; + interrupt-names = "uart", "dma"; + clocks = <&scmi_clk 190>; + clock-names = "sw_baud"; + }; diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt new file mode 100644 index 000000000..87a6c375c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt @@ -0,0 +1,19 @@ +* Universal Asynchronous Receiver/Transmitter (UART) + +- compatible: "cavium,octeon-3860-uart" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the UART register bank. + +- interrupts: A single interrupt specifier. + +- current-speed: Optional, the current bit rate in bits per second. + +Example: + uart1: serial@1180000000c00 { + compatible = "cavium,octeon-3860-uart","ns16550"; + reg = <0x11800 0x00000c00 0x0 0x400>; + current-speed = <115200>; + interrupts = <0 35>; + }; diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.yaml b/Documentation/devicetree/bindings/serial/cdns,uart.yaml new file mode 100644 index 000000000..876b8cf1c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cdns,uart.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/cdns,uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence UART Controller + +maintainers: + - Michal Simek + +allOf: + - $ref: /schemas/serial.yaml# + +properties: + compatible: + oneOf: + - description: UART controller for Zynq-7xxx SoC + items: + - const: xlnx,xuartps + - const: cdns,uart-r1p8 + - description: UART controller for Zynq Ultrascale+ MPSoC + items: + - const: xlnx,zynqmp-uart + - const: cdns,uart-r1p12 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: uart_clk + - const: pclk + + cts-override: + description: | + Override the CTS modem status signal. This signal will + always be reported as active instead of being obtained + from the modem status register. Define this if your serial + port does not use this pin. + type: boolean + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + uart0: serial@e0000000 { + compatible = "xlnx,xuartps", "cdns,uart-r1p8"; + clocks = <&clkc 23>, <&clkc 40>; + clock-names = "uart_clk", "pclk"; + reg = <0xE0000000 0x1000>; + interrupts = <0 27 4>; + }; diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt new file mode 100644 index 000000000..07013fa60 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt @@ -0,0 +1,31 @@ +* Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART) + +Required properties: +- compatible: Should be "cirrus,ep7209-uart". +- reg: Address and length of the register set for the device. +- interrupts: Should contain UART TX and RX interrupt. +- clocks: Should contain UART core clock number. +- syscon: Phandle to SYSCON node, which contain UART control bits. + +Optional properties: +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. + +Note: Each UART port should have an alias correctly numbered +in "aliases" node. + +Example: + aliases { + serial0 = &uart1; + }; + + uart1: uart@80000480 { + compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart"; + reg = <0x80000480 0x80>; + interrupts = <12 13>; + clocks = <&clks 11>; + syscon = <&syscon1>; + cts-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>; + dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>; + dcd-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/serial/digicolor-usart.txt b/Documentation/devicetree/bindings/serial/digicolor-usart.txt new file mode 100644 index 000000000..2d3ede668 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/digicolor-usart.txt @@ -0,0 +1,27 @@ +Binding for Conexant Digicolor USART + +Note: this binding is only applicable for using the USART peripheral as +UART. USART also support synchronous serial protocols like SPI and I2S. Use +the binding that matches the wiring of your system. + +Required properties: +- compatible : should be "cnxt,cx92755-usart". +- reg: Should contain USART controller registers location and length. +- interrupts: Should contain a single USART controller interrupt. +- clocks: Must contain phandles to the USART clock + See ../clocks/clock-bindings.txt for details. + +Note: Each UART port should have an alias correctly numbered +in "aliases" node. + +Example: + aliases { + serial0 = &uart0; + }; + + uart0: uart@f0000740 { + compatible = "cnxt,cx92755-usart"; + reg = <0xf0000740 0x20>; + clocks = <&main_clk>; + interrupts = <44>; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml new file mode 100644 index 000000000..8b643bae3 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl,s32-linflexuart.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/fsl,s32-linflexuart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale LINFlexD UART + +description: | + The LINFlexD controller implements several LIN protocol versions, as well + as support for full-duplex UART communication through 8-bit and 9-bit + frames. See chapter 47 ("LINFlexD") in the reference manual + https://www.nxp.com/webapp/Download?colCode=S32V234RM. + +maintainers: + - Chester Lin + +allOf: + - $ref: "serial.yaml" + +properties: + compatible: + oneOf: + - const: fsl,s32v234-linflexuart + - items: + - const: nxp,s32g2-linflexuart + - const: fsl,s32v234-linflexuart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + serial@40053000 { + compatible = "fsl,s32v234-linflexuart"; + reg = <0x40053000 0x1000>; + interrupts = <0 59 4>; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml b/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml new file mode 100644 index 000000000..9d949296a --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART) + +maintainers: + - Fabio Estevam + +allOf: + - $ref: "serial.yaml" + - $ref: "rs485.yaml" + +properties: + compatible: + oneOf: + - const: fsl,imx1-uart + - const: fsl,imx21-uart + - items: + - enum: + - fsl,imx25-uart + - fsl,imx27-uart + - fsl,imx31-uart + - fsl,imx35-uart + - fsl,imx50-uart + - fsl,imx51-uart + - fsl,imx53-uart + - fsl,imx6q-uart + - const: fsl,imx21-uart + - items: + - enum: + - fsl,imx6sl-uart + - fsl,imx6sll-uart + - fsl,imx6sx-uart + - const: fsl,imx6q-uart + - const: fsl,imx21-uart + - items: + - enum: + - fsl,imx6ul-uart + - fsl,imx7d-uart + - fsl,imx8mm-uart + - fsl,imx8mn-uart + - fsl,imx8mp-uart + - fsl,imx8mq-uart + - const: fsl,imx6q-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + fsl,dte-mode: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Indicate the uart works in DTE mode. The uart works in DCE mode by default. + + fsl,inverted-tx: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Indicate that the hardware attached to the peripheral inverts the signal + transmitted, and that the peripheral should invert its output using the + INVT registers. + + fsl,inverted-rx: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Indicate that the hardware attached to the peripheral inverts the signal + received, and that the peripheral should invert its input using the + INVR registers. + + fsl,dma-info: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + description: | + First cell contains the size of DMA buffer chunks, second cell contains + the amount of chunks used for the device. Multiplying both numbers is + the total size of memory used for receiving data. + When not being configured the system will use default settings, which + are sensible for most use cases. If you need low latency processing on + slow connections this needs to be configured appropriately. + + uart-has-rtscts: true + + rs485-rts-delay: true + rs485-rts-active-low: true + rs485-rx-during-tx: true + linux,rs485-enabled-at-boot-time: true + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + aliases { + serial0 = &uart1; + }; + + uart1: serial@73fbc000 { + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x73fbc000 0x4000>; + interrupts = <31>; + uart-has-rtscts; + fsl,dte-mode; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.yaml b/Documentation/devicetree/bindings/serial/fsl-lpuart.yaml new file mode 100644 index 000000000..30eaa62e1 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale low power universal asynchronous receiver/transmitter (lpuart) + +maintainers: + - Fugang Duan + +allOf: + - $ref: "rs485.yaml" + +properties: + compatible: + oneOf: + - enum: + - fsl,vf610-lpuart + - fsl,ls1021a-lpuart + - fsl,ls1028a-lpuart + - fsl,imx7ulp-lpuart + - fsl,imx8qxp-lpuart + - fsl,imxrt1050-lpuart + - items: + - enum: + - fsl,imx93-lpuart + - fsl,imx8ulp-lpuart + - const: fsl,imx7ulp-lpuart + - items: + - enum: + - fsl,imx8qm-lpuart + - fsl,imx8dxl-lpuart + - const: fsl,imx8qxp-lpuart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: ipg clock + - description: baud clock + minItems: 1 + + clock-names: + items: + - const: ipg + - const: baud + minItems: 1 + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + + rs485-rts-active-low: true + linux,rs485-enabled-at-boot-time: true + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include + + serial@40027000 { + compatible = "fsl,vf610-lpuart"; + reg = <0x40027000 0x1000>; + interrupts = <0 61 0x00>; + clocks = <&clks VF610_CLK_UART0>; + clock-names = "ipg"; + dmas = <&edma0 0 2>, <&edma0 0 3>; + dma-names = "rx","tx"; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.yaml b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.yaml new file mode 100644 index 000000000..14c7594c8 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/fsl-mxs-auart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS Application UART (AUART) + +maintainers: + - Fabio Estevam + +allOf: + - $ref: "serial.yaml" + +properties: + compatible: + enum: + - fsl,imx23-auart + - fsl,imx28-auart + - alphascale,asm9260-auart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + + clocks: + items: + - description: mod clock + - description: ahb clock + minItems: 1 + + clock-names: + items: + - const: mod + - const: ahb + minItems: 1 + + uart-has-rtscts: true + rts-gpios: true + cts-gpios: true + dtr-gpios: true + dsr-gpios: true + rng-gpios: true + dcd-gpios: true + +if: + properties: + compatible: + contains: + enum: + - alphascale,asm9260-auart +then: + required: + - clocks + - clock-names + +required: + - compatible + - reg + - interrupts + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + aliases { + serial0 = &auart0; + }; + + auart0: serial@8006a000 { + compatible = "fsl,imx28-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112>; + dmas = <&dma_apbx 8>, <&dma_apbx 9>; + dma-names = "rx", "tx"; + clocks = <&clks 45>; + }; diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.yaml b/Documentation/devicetree/bindings/serial/ingenic,uart.yaml new file mode 100644 index 000000000..9ca7a18ec --- /dev/null +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/ingenic,uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs UART controller devicetree bindings + +maintainers: + - Paul Cercueil + +allOf: + - $ref: serial.yaml# + +properties: + $nodename: + pattern: "^serial@[0-9a-f]+$" + + compatible: + oneOf: + - enum: + - ingenic,jz4740-uart + - ingenic,jz4760-uart + - ingenic,jz4780-uart + - ingenic,x1000-uart + - items: + - enum: + - ingenic,jz4770-uart + - ingenic,jz4775-uart + - const: ingenic,jz4760-uart + - items: + - const: ingenic,jz4725b-uart + - const: ingenic,jz4740-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Baud clock + - description: UART module clock + + clock-names: + items: + - const: baud + - const: module + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + #include + #include + #include + serial@10032000 { + compatible = "ingenic,jz4780-uart"; + reg = <0x10032000 0x100>; + + interrupt-parent = <&intc>; + interrupts = <49>; + + clocks = <&ext>, <&cgu JZ4780_CLK_UART2>; + clock-names = "baud", "module"; + + dmas = <&dma JZ4780_DMA_UART2_RX 0xffffffff>, + <&dma JZ4780_DMA_UART2_TX 0xffffffff>; + dma-names = "rx", "tx"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + reset-gpios = <&gpf 8 GPIO_ACTIVE_HIGH>; + vbat-supply = <&wlan0_power>; + device-wakeup-gpios = <&gpf 5 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpf 6 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpf 4 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/serial/lantiq_asc.txt b/Documentation/devicetree/bindings/serial/lantiq_asc.txt new file mode 100644 index 000000000..40e81a581 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/lantiq_asc.txt @@ -0,0 +1,31 @@ +Lantiq SoC ASC serial controller + +Required properties: +- compatible : Should be "lantiq,asc" +- reg : Address and length of the register set for the device +- interrupts: the 3 (tx rx err) interrupt numbers. The interrupt specifier + depends on the interrupt-parent interrupt controller. + +Optional properties: +- clocks: Should contain frequency clock and gate clock +- clock-names: Should be "freq" and "asc" + +Example: + +asc0: serial@16600000 { + compatible = "lantiq,asc"; + reg = <0x16600000 0x100000>; + interrupt-parent = <&gic>; + interrupts = , + , + ; + clocks = <&cgu CLK_SSX4>, <&cgu GCLK_UART>; + clock-names = "freq", "asc"; +}; + +asc1: serial@e100c00 { + compatible = "lantiq,asc"; + reg = <0xE100C00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; +}; diff --git a/Documentation/devicetree/bindings/serial/litex,liteuart.yaml b/Documentation/devicetree/bindings/serial/litex,liteuart.yaml new file mode 100644 index 000000000..c4f1f489d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/litex,liteuart.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/litex,liteuart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LiteUART serial controller + +maintainers: + - Karol Gugala + - Mateusz Holenko + +description: | + LiteUART serial controller is a part of the LiteX FPGA SoC builder. It supports + multiple CPU architectures, currently including e.g. OpenRISC and RISC-V. + +properties: + compatible: + const: litex,liteuart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + uart0: serial@e0001800 { + compatible = "litex,liteuart"; + reg = <0xe0001800 0x100>; + interrupts = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/maxim,max310x.txt b/Documentation/devicetree/bindings/serial/maxim,max310x.txt new file mode 100644 index 000000000..79e10a05a --- /dev/null +++ b/Documentation/devicetree/bindings/serial/maxim,max310x.txt @@ -0,0 +1,48 @@ +* Maxim MAX310X advanced Universal Asynchronous Receiver-Transmitter (UART) + +Required properties: +- compatible: Should be one of the following: + - "maxim,max3107" for Maxim MAX3107, + - "maxim,max3108" for Maxim MAX3108, + - "maxim,max3109" for Maxim MAX3109, + - "maxim,max14830" for Maxim MAX14830. +- reg: SPI chip select number. +- interrupts: Specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- clocks: phandle to the IC source clock. +- clock-names: Should be "xtal" if clock is an external crystal or + "osc" if an external clock source is used. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + +/ { + clocks { + spi_uart_clk: osc_max14830 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <3686400>; + }; + + }; +}; + +&spi0 { + max14830: max14830@0 { + compatible = "maxim,max14830"; + reg = <0>; + clocks = <&spi_uart_clk>; + clock-names = "osc"; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + gpio-controller; + #gpio-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/serial/mediatek,uart.yaml b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml new file mode 100644 index 000000000..fe098d98a --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/mediatek,uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Universal Asynchronous Receiver/Transmitter (UART) + +maintainers: + - Matthias Brugger + +allOf: + - $ref: serial.yaml# + +description: | + The MediaTek UART is based on the basic 8250 UART and compatible + with 16550A, with enhancements for high speed baud rates and + support for DMA. + +properties: + compatible: + oneOf: + - const: mediatek,mt6577-uart + - items: + - enum: + - mediatek,mt2701-uart + - mediatek,mt2712-uart + - mediatek,mt6580-uart + - mediatek,mt6582-uart + - mediatek,mt6589-uart + - mediatek,mt6755-uart + - mediatek,mt6765-uart + - mediatek,mt6779-uart + - mediatek,mt6795-uart + - mediatek,mt6797-uart + - mediatek,mt7622-uart + - mediatek,mt7623-uart + - mediatek,mt7629-uart + - mediatek,mt7986-uart + - mediatek,mt8127-uart + - mediatek,mt8135-uart + - mediatek,mt8173-uart + - mediatek,mt8183-uart + - mediatek,mt8186-uart + - mediatek,mt8188-uart + - mediatek,mt8192-uart + - mediatek,mt8195-uart + - mediatek,mt8516-uart + - const: mediatek,mt6577-uart + + reg: + description: The base address of the UART register bank + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: The clock the baudrate is derived from + - description: The bus clock for register accesses + + clock-names: + minItems: 1 + items: + - const: baud + - const: bus + + dmas: + items: + - description: phandle to TX DMA + - description: phandle to RX DMA + + dma-names: + items: + - const: tx + - const: rx + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + description: + The UART interrupt and optionally the RX in-band wakeup interrupt. + minItems: 1 + items: + - const: uart + - const: wakeup + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + minItems: 1 + items: + - const: default + - const: sleep + +required: + - compatible + - reg + - clocks + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include + + serial@11006000 { + compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart"; + reg = <0x11006000 0x400>; + interrupts = , + ; + interrupt-names = "uart", "wakeup"; + clocks = <&uart_clk>, <&bus_clk>; + clock-names = "baud", "bus"; + pinctrl-0 = <&uart_pin>; + pinctrl-1 = <&uart_pin_sleep>; + pinctrl-names = "default", "sleep"; + }; diff --git a/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt new file mode 100644 index 000000000..c8dd440e9 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt @@ -0,0 +1,29 @@ +* Microchip Universal Asynchronous Receiver Transmitter (UART) + +Required properties: +- compatible: Should be "microchip,pic32mzda-uart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the UART peripheral. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Optional properties: +- cts-gpios: CTS pin for UART + +Example: + uart1: serial@1f822000 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822000 0x50>; + interrupts = <112 IRQ_TYPE_LEVEL_HIGH>, + <113 IRQ_TYPE_LEVEL_HIGH>, + <114 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rootclk PB2CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1 + &pinctrl_uart1_cts + &pinctrl_uart1_rts>; + cts-gpios = <&gpio1 15 0>; + }; diff --git a/Documentation/devicetree/bindings/serial/milbeaut-uart.txt b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt new file mode 100644 index 000000000..3d2fb1a7b --- /dev/null +++ b/Documentation/devicetree/bindings/serial/milbeaut-uart.txt @@ -0,0 +1,21 @@ +Socionext Milbeaut UART controller + +Required properties: +- compatible: should be "socionext,milbeaut-usio-uart". +- reg: offset and length of the register set for the device. +- interrupts: two interrupts specifier. +- interrupt-names: should be "rx", "tx". +- clocks: phandle to the input clock. + +Optional properties: +- auto-flow-control: flow control enable. + +Example: + usio1: usio_uart@1e700010 { + compatible = "socionext,milbeaut-usio-uart"; + reg = <0x1e700010 0x10>; + interrupts = <0 141 0x4>, <0 149 0x4>; + interrupt-names = "rx", "tx"; + clocks = <&clk 2>; + auto-flow-control; + }; diff --git a/Documentation/devicetree/bindings/serial/mrvl,pxa-ssp.txt b/Documentation/devicetree/bindings/serial/mrvl,pxa-ssp.txt new file mode 100644 index 000000000..d10cc06c0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mrvl,pxa-ssp.txt @@ -0,0 +1,64 @@ +Device tree bindings for Marvell PXA SSP ports + +Required properties: + + - compatible: Must be one of + mrvl,pxa25x-ssp + mvrl,pxa25x-nssp + mrvl,pxa27x-ssp + mrvl,pxa3xx-ssp + mvrl,pxa168-ssp + mrvl,pxa910-ssp + mrvl,ce4100-ssp + + - reg: The memory base + - dmas: Two dma phandles, one for rx, one for tx + - dma-names: Must be "rx", "tx" + + +Example for PXA3xx: + + ssp0: ssp@41000000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41000000 0x40>; + ssp-id = <1>; + interrupts = <24>; + clock-names = "pxa27x-ssp.0"; + dmas = <&dma 13 + &dma 14>; + dma-names = "rx", "tx"; + }; + + ssp1: ssp@41700000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41700000 0x40>; + ssp-id = <2>; + interrupts = <16>; + clock-names = "pxa27x-ssp.1"; + dmas = <&dma 15 + &dma 16>; + dma-names = "rx", "tx"; + }; + + ssp2: ssp@41900000 { + compatibl3 = "mrvl,pxa3xx-ssp"; + reg = <0x41900000 0x40>; + ssp-id = <3>; + interrupts = <0>; + clock-names = "pxa27x-ssp.2"; + dmas = <&dma 66 + &dma 67>; + dma-names = "rx", "tx"; + }; + + ssp3: ssp@41a00000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41a00000 0x40>; + ssp-id = <4>; + interrupts = <13>; + clock-names = "pxa27x-ssp.3"; + dmas = <&dma 2 + &dma 3>; + dma-names = "rx", "tx"; + }; + diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt new file mode 100644 index 000000000..a062bbca5 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt @@ -0,0 +1,56 @@ +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs + e.g., Armada-3700. + +Required properties: +- compatible: + - "marvell,armada-3700-uart" for the standard variant of the UART + (32 bytes FIFO, no DMA, level interrupts, 8-bit access to the + FIFO), called also UART1. + - "marvell,armada-3700-uart-ext" for the extended variant of the + UART (128 bytes FIFO, DMA, front interrupts, 8-bit or 32-bit + accesses to the FIFO), called also UART2. +- reg: offset and length of the register set for the device. +- clocks: UART reference clock used to derive the baudrate. If no clock + is provided (possible only with the "marvell,armada-3700-uart" + compatible string for backward compatibility), it will only work + if the baudrate was initialized by the bootloader and no baudrate + change will then be possible. When provided it should be UART1-clk + for standard variant of UART and UART2-clk for extended variant + of UART. TBG clock (with UART TBG divisors d1=d2=1) or xtal clock + should not be used and are supported only for backward compatibility. +- interrupts: + - Must contain three elements for the standard variant of the IP + (marvell,armada-3700-uart): "uart-sum", "uart-tx" and "uart-rx", + respectively the UART sum interrupt, the UART TX interrupt and + UART RX interrupt. A corresponding interrupt-names property must + be defined. + - Must contain two elements for the extended variant of the IP + (marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx", + respectively the UART TX interrupt and the UART RX interrupt. A + corresponding interrupt-names property must be defined. + - For backward compatibility reasons, a single element interrupts + property is also supported for the standard variant of the IP, + containing only the UART sum interrupt. This form is deprecated + and should no longer be used. + +Example: + uart0: serial@12000 { + compatible = "marvell,armada-3700-uart"; + reg = <0x12000 0x18>; + clocks = <&uartclk 0>; + interrupts = + , + , + ; + interrupt-names = "uart-sum", "uart-tx", "uart-rx"; + }; + + uart1: serial@12200 { + compatible = "marvell,armada-3700-uart-ext"; + reg = <0x12200 0x30>; + clocks = <&uartclk 1>; + interrupts = + , + ; + interrupt-names = "uart-tx", "uart-rx"; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.yaml b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.yaml new file mode 100644 index 000000000..e2d111b3e --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/nvidia,tegra194-tcu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra Combined UART (TCU) + +maintainers: + - Thierry Reding + - Jonathan Hunter + +description: + The TCU is a system for sharing a hardware UART instance among multiple + systems within the Tegra SoC. It is implemented through a mailbox- + based protocol where each "virtual UART" has a pair of mailboxes, one + for transmitting and one for receiving, that is used to communicate + with the hardware implementing the TCU. + +properties: + $nodename: + pattern: "^serial(@.*)?$" + + compatible: + oneOf: + - const: nvidia,tegra194-tcu + - items: + - enum: + - nvidia,tegra234-tcu + - const: nvidia,tegra194-tcu + + mbox-names: + items: + - const: rx + - const: tx + + mboxes: + description: | + List of phandles to mailbox channels used for receiving and + transmitting data from and to the hardware UART. + items: + - description: mailbox for receiving data from hardware UART + - description: mailbox for transmitting data to hardware UART + +required: + - compatible + - mbox-names + - mboxes + +additionalProperties: false + +examples: + - | + #include + + tcu: serial { + compatible = "nvidia,tegra194-tcu"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM 0>, + <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM 1>; + mbox-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt new file mode 100644 index 000000000..f70930403 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -0,0 +1,73 @@ +NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. + +Required properties: +- compatible : should be, + "nvidia,tegra20-hsuart" for Tegra20, + "nvidia,tegra30-hsuart" for Tegra30, + "nvidia,tegra186-hsuart" for Tegra186, + "nvidia,tegra194-hsuart" for Tegra194. + +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - serial +- dmas : Must contain an entry for each entry in dma-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx + +Optional properties: +- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable + only if all 8 lines of UART controller are pinmuxed. +- nvidia,adjust-baud-rates: List of entries providing percentage of baud rate + adjustment within a range. + Each entry contains sets of 3 values. Range low/high and adjusted rate. + + When baud rate set on controller falls within the range mentioned in this + field, baud rate will be adjusted by percentage mentioned here. + Ex: <9600 115200 200> + Increase baud rate by 2% when set baud rate falls within range 9600 to 115200 + +Baud Rate tolerance: + Standard UART devices are expected to have tolerance for baud rate error by + -4 to +4 %. All Tegra devices till Tegra210 had this support. However, + Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level + is 0% to +4% in 1-stop config. Otherwise, the received data will have + corruption/invalid framing errors. Parker errata suggests adjusting baud + rate to be higher than the deviations observed in Tx. + + Tx deviation of connected device can be captured over scope (or noted from + its spec) for valid range and Tegra baud rate has to be set above actual + Tx baud rate observed. To do this we use nvidia,adjust-baud-rates + + As an example, consider there is deviation observed in Tx for baud rates as + listed below. + 0 to 9600 has 1% deviation + 9600 to 115200 2% deviation + This slight deviation is expcted and Tegra UART is expected to handle it. Due + to the issue stated above, baud rate on Tegra UART should be set equal to or + above deviation observed for avoiding frame errors. + Property should be set like this + nvidia,adjust-baud-rates = <0 9600 100>, + <9600 115200 200>; + +Example: + +serial@70006000 { + compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart"; + reg = <0x70006000 0x40>; + reg-shift = <2>; + interrupts = <0 36 0x04>; + nvidia,enable-modem-interrupt; + clocks = <&tegra_car 6>; + resets = <&tegra_car 6>; + reset-names = "serial"; + dmas = <&apbdma 8>, <&apbdma 8>; + dma-names = "rx", "tx"; + nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */ +}; diff --git a/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt new file mode 100644 index 000000000..04e23e63e --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt @@ -0,0 +1,28 @@ +* NXP LPC1850 UART + +Required properties: +- compatible : "nxp,lpc1850-uart", "ns16550a". +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clocks : phandle to the input clocks. +- clock-names : required elements: "uartclk", "reg". + +Optional properties: +- dmas : Two or more DMA channel specifiers following the + convention outlined in bindings/dma/dma.txt +- dma-names : Names for the dma channels, if present. There must + be at least one channel named "tx" for transmit + and named "rx" for receive. + +Since it's also possible to also use the of_serial.c driver all +parameters from 8250.txt also apply but are optional. + +Example: +uart0: serial@40081000 { + compatible = "nxp,lpc1850-uart", "ns16550a"; + reg = <0x40081000 0x1000>; + reg-shift = <2>; + interrupts = <24>; + clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>; + clock-names = "uartclk", "reg"; +}; diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt new file mode 100644 index 000000000..1a7e4bff0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -0,0 +1,118 @@ +* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART) +* i2c as bus + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: I2C address of the SC16IS7xx device. +- interrupts: Should contain the UART interrupt +- clocks: Reference to the IC source clock. + OR (when there is no clock provider visible to the platform) +- clock-frequency: The source clock frequency for the IC. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. +- irda-mode-ports: An array that lists the indices of the port that + should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. + +Example: + sc16is750: sc16is750@51 { + compatible = "nxp,sc16is750"; + reg = <0x51>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@53 { + compatible = "nxp,sc16is752"; + reg = <0x53>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@54 { + compatible = "nxp,sc16is752"; + reg = <0x54>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + }; + +* spi as bus + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: SPI chip select number. +- interrupts: Specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- clocks: phandle to the IC source clock. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. +- irda-mode-ports: An array that lists the indices of the port that + should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. + +Example: + sc16is750: sc16is750@0 { + compatible = "nxp,sc16is750"; + reg = <0>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@1 { + compatible = "nxp,sc16is752"; + reg = <1>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@2 { + compatible = "nxp,sc16is752"; + reg = <2>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + }; diff --git a/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt new file mode 100644 index 000000000..0d439dfc1 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt @@ -0,0 +1,14 @@ +* NXP LPC32xx SoC High Speed UART + +Required properties: +- compatible: Should be "nxp,lpc3220-hsuart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Example: + + uart1: serial@40014000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x40014000 0x1000>; + interrupts = <26 0>; + }; diff --git a/Documentation/devicetree/bindings/serial/pl011.yaml b/Documentation/devicetree/bindings/serial/pl011.yaml new file mode 100644 index 000000000..80af72859 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/pl011.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM AMBA Primecell PL011 serial UART + +maintainers: + - Rob Herring + +allOf: + - $ref: serial.yaml# + +# Need a custom select here or 'arm,primecell' will match on lots of nodes +select: + properties: + compatible: + contains: + enum: + - arm,pl011 + required: + - compatible + +properties: + compatible: + items: + - const: arm,pl011 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + description: + When present, must have one state named "default", + and may contain a second name named "sleep". The former + state sets up pins for ordinary operation whereas + the latter state will put the associated pins to sleep + when the UART is unused + minItems: 1 + items: + - const: default + - const: sleep + + clocks: + description: + When present, the first clock listed must correspond to + the clock named UARTCLK on the IP block, i.e. the clock + to the external serial line, whereas the second clock + must correspond to the PCLK clocking the internal logic + of the block. Just listing one clock (the first one) is + deprecated. + maxItems: 2 + + clock-names: + items: + - const: uartclk + - const: apb_pclk + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: tx + + auto-poll: + description: + Enables polling when using RX DMA. + type: boolean + + poll-rate-ms: + description: + Rate at which poll occurs when auto-poll is set. + default 100ms. + default: 100 + + poll-timeout-ms: + description: + Poll timeout when auto-poll is set, default + 3000ms. + default: 3000 + + resets: + maxItems: 1 + + reg-io-width: + description: + The size (in bytes) of the IO accesses that should be performed + on the device. + enum: [1, 4] + +required: + - compatible + - reg + - interrupts + +dependencies: + poll-rate-ms: [ auto-poll ] + poll-timeout-ms: [ auto-poll ] + +unevaluatedProperties: false + +examples: + - | + serial@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 4>; + dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&foo_clk>, <&bar_clk>; + clock-names = "uartclk", "apb_pclk"; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/qca,ar9330-uart.yaml b/Documentation/devicetree/bindings/serial/qca,ar9330-uart.yaml new file mode 100644 index 000000000..a644e5af1 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qca,ar9330-uart.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/qca,ar9330-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros AR9330 High-Speed UART + +maintainers: + - Oleksij Rempel + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + const: qca,ar9330-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: uart + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + serial@18020000 { + compatible = "qca,ar9330-uart"; + reg = <0x18020000 0x14>; + clocks = <&ref>; + clock-names = "uart"; + interrupt-parent = <&intc>; + interrupts = <3>; + }; +... diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt new file mode 100644 index 000000000..ce8c90161 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt @@ -0,0 +1,25 @@ +* MSM Serial UART + +The MSM serial UART hardware is designed for low-speed use cases where a +dma-engine isn't needed. From a software perspective it's mostly compatible +with the MSM serial UARTDM except that it only supports reading and writing one +character at a time. + +Required properties: +- compatible: Should contain "qcom,msm-uart" +- reg: Should contain UART register location and length. +- interrupts: Should contain UART interrupt. +- clocks: Should contain the core clock. +- clock-names: Should be "core". + +Example: + +A uart device at 0xa9c00000 with interrupt 11. + +serial@a9c00000 { + compatible = "qcom,msm-uart"; + reg = <0xa9c00000 0x1000>; + interrupts = <11>; + clocks = <&uart_cxc>; + clock-names = "core"; +}; diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml new file mode 100644 index 000000000..484b9a51f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/qcom,msm-uartdm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm MSM Serial UARTDM + +maintainers: + - Andy Gross + - Bjorn Andersson + - Krzysztof Kozlowski + +description: | + The MSM serial UARTDM hardware is designed for high-speed use cases where the + transmit and/or receive channels can be offloaded to a dma-engine. From a + software perspective it's mostly compatible with the MSM serial UART except + that it supports reading and writing multiple characters at a time. + + Note:: Aliases may be defined to ensure the correct ordering of the UARTs. + The alias serialN will result in the UART being assigned port N. If any + serialN alias exists, then an alias must exist for each enabled UART. The + serialN aliases should be in a .dts file instead of in a .dtsi file. + +properties: + compatible: + items: + - enum: + - qcom,msm-uartdm-v1.1 + - qcom,msm-uartdm-v1.2 + - qcom,msm-uartdm-v1.3 + - qcom,msm-uartdm-v1.4 + - const: qcom,msm-uartdm + + clocks: + maxItems: 2 + + clock-names: + items: + - const: core + - const: iface + + dmas: + maxItems: 2 + + dma-names: + items: + - const: tx + - const: rx + + interrupts: + maxItems: 1 + + qcom,rx-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Identificator for Client Rate Control Interface to be used with RX DMA + channel. Required when using DMA for reception with UARTDM v1.3 and + below. + + qcom,tx-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Identificator for Client Rate Control Interface to be used with TX DMA + channel. Required when using DMA for transmission with UARTDM v1.3 and + below. + + reg: + minItems: 1 + items: + - description: Main control registers + - description: An optional second register location shall specify the GSBI control region. + +required: + - compatible + - clock-names + - clocks + - interrupts + - reg + +unevaluatedProperties: false + +allOf: + - $ref: /schemas/serial/serial.yaml# + + - if: + properties: + compatible: + contains: + const: qcom,msm-uartdm-v1.3 + then: + properties: + reg: + minItems: 2 + else: + properties: + reg: + maxItems: 1 + +examples: + - | + #include + + serial@f991e000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0xf991e000 0x1000>; + interrupts = ; + clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>; + clock-names = "core", "iface"; + dmas = <&dma0 0>, <&dma0 1>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml b/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml new file mode 100644 index 000000000..05a699980 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/qcom,serial-geni-qcom.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Qualcomm Geni based QUP UART interface + +maintainers: + - Andy Gross + - Bjorn Andersson + +allOf: + - $ref: /schemas/serial/serial.yaml# + +properties: + compatible: + enum: + - qcom,geni-uart + - qcom,geni-debug-uart + + clocks: + maxItems: 1 + + clock-names: + const: se + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: qup-core + - const: qup-config + + interrupts: + minItems: 1 + items: + - description: UART core irq + - description: Wakeup irq (RX GPIO) + + operating-points-v2: true + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + minItems: 1 + items: + - const: default + - const: sleep + + power-domains: + maxItems: 1 + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - interrupts + - reg + +unevaluatedProperties: false + +examples: + - | + #include + #include + #include + + serial@a88000 { + compatible = "qcom,geni-uart"; + reg = <0xa88000 0x7000>; + interrupts = ; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-0 = <&qup_uart0_default>; + pinctrl-names = "default"; + interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>; + interconnect-names = "qup-core", "qup-config"; + }; +... diff --git a/Documentation/devicetree/bindings/serial/rda,8810pl-uart.yaml b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.yaml new file mode 100644 index 000000000..5f4ed8221 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rda,8810pl-uart.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/rda,8810pl-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro UART Interface + +maintainers: + - Manivannan Sadhasivam + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + const: rda,8810pl-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include + + uart3: serial@20a90000 { + compatible = "rda,8810pl-uart"; + reg = <0x20a90000 0x1000>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_clk>; + }; +... diff --git a/Documentation/devicetree/bindings/serial/renesas,em-uart.yaml b/Documentation/devicetree/bindings/serial/renesas,em-uart.yaml new file mode 100644 index 000000000..b25aca733 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,em-uart.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,em-uart.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas EMMA Mobile UART Interface + +maintainers: + - Magnus Damm + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a09g011-uart # RZ/V2M + - const: renesas,em-uart # generic EMMA Mobile compatible UART + + - items: + - const: renesas,em-uart # generic EMMA Mobile compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: UART functional clock + - description: Internal clock to access the registers + + clock-names: + minItems: 1 + items: + - const: sclk + - const: pclk + +allOf: + - $ref: serial.yaml# + + - if: + properties: + compatible: + contains: + const: renesas,r9a09g011-uart + then: + properties: + clocks: + minItems: 2 + clock-names: + minItems: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include + uart0: serial@e1020000 { + compatible = "renesas,em-uart"; + reg = <0xe1020000 0x38>; + interrupts = ; + clocks = <&usia_u0_sclk>; + clock-names = "sclk"; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,hscif.yaml b/Documentation/devicetree/bindings/serial/renesas,hscif.yaml new file mode 100644 index 000000000..1957b9d78 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,hscif.yaml @@ -0,0 +1,150 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,hscif.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas High Speed Serial Communication Interface with FIFO (HSCIF) + +maintainers: + - Geert Uytterhoeven + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,hscif-r8a7778 # R-Car M1 + - renesas,hscif-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-hscif # R-Car Gen1 + - const: renesas,hscif # generic HSCIF compatible UART + + - items: + - enum: + - renesas,hscif-r8a7742 # RZ/G1H + - renesas,hscif-r8a7743 # RZ/G1M + - renesas,hscif-r8a7744 # RZ/G1N + - renesas,hscif-r8a7745 # RZ/G1E + - renesas,hscif-r8a77470 # RZ/G1C + - renesas,hscif-r8a7790 # R-Car H2 + - renesas,hscif-r8a7791 # R-Car M2-W + - renesas,hscif-r8a7792 # R-Car V2H + - renesas,hscif-r8a7793 # R-Car M2-N + - renesas,hscif-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-hscif # R-Car Gen2 and RZ/G1 + - const: renesas,hscif # generic HSCIF compatible UART + + - items: + - enum: + - renesas,hscif-r8a774a1 # RZ/G2M + - renesas,hscif-r8a774b1 # RZ/G2N + - renesas,hscif-r8a774c0 # RZ/G2E + - renesas,hscif-r8a774e1 # RZ/G2H + - renesas,hscif-r8a7795 # R-Car H3 + - renesas,hscif-r8a7796 # R-Car M3-W + - renesas,hscif-r8a77961 # R-Car M3-W+ + - renesas,hscif-r8a77965 # R-Car M3-N + - renesas,hscif-r8a77970 # R-Car V3M + - renesas,hscif-r8a77980 # R-Car V3H + - renesas,hscif-r8a77990 # R-Car E3 + - renesas,hscif-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-hscif # R-Car Gen3 and RZ/G2 + - const: renesas,hscif # generic HSCIF compatible UART + + - items: + - enum: + - renesas,hscif-r8a779a0 # R-Car V3U + - renesas,hscif-r8a779f0 # R-Car S4-8 + - renesas,hscif-r8a779g0 # R-Car V4H + - const: renesas,rcar-gen4-hscif # R-Car Gen4 + - const: renesas,hscif # generic HSCIF compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + enum: + - fck # UART functional clock + - hsck # optional external clock input + - brg_int # optional internal clock source for BRG frequency divider + - scif_clk # optional external clock source for BRG frequency divider + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +unevaluatedProperties: false + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-hscif + - renesas,rcar-gen3-hscif + - renesas,rcar-gen4-hscif +then: + required: + - resets + +examples: + - | + #include + #include + #include + aliases { + serial1 = &hscif1; + }; + + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a7795", "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0xe6550000 96>; + interrupts = ; + clocks = <&cpg CPG_MOD 519>, <&cpg CPG_CORE R8A7795_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x33>, <&dmac1 0x32>, <&dmac2 0x33>, <&dmac2 0x32>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 519>; + uart-has-rtscts; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci.yaml b/Documentation/devicetree/bindings/serial/renesas,sci.yaml new file mode 100644 index 000000000..bf7708a7a --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,sci.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,sci.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communication Interface + +maintainers: + - Geert Uytterhoeven + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a07g043-sci # RZ/G2UL + - renesas,r9a07g044-sci # RZ/G2{L,LC} + - renesas,r9a07g054-sci # RZ/V2L + - const: renesas,sci # generic SCI compatible UART + + - items: + - const: renesas,sci # generic SCI compatible UART + + reg: + maxItems: 1 + + interrupts: + items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Transmit end interrupt + + interrupt-names: + items: + - const: eri + - const: rxi + - const: txi + - const: tei + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + maxItems: 2 + items: + enum: + - fck # UART functional clock + - sck # optional external clock input + + uart-has-rtscts: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +if: + properties: + compatible: + contains: + enum: + - renesas,r9a07g043-sci + - renesas,r9a07g044-sci + - renesas,r9a07g054-sci +then: + properties: + resets: + maxItems: 1 + + power-domains: + maxItems: 1 + + required: + - resets + - power-domains + +unevaluatedProperties: false + +examples: + - | + #include + #include + + aliases { + serial0 = &sci0; + }; + + sci0: serial@1004d000 { + compatible = "renesas,r9a07g044-sci", "renesas,sci"; + reg = <0x1004d000 0x400>; + interrupts = , + , + , + ; + interrupt-names = "eri", "rxi", "txi", "tei"; + clocks = <&cpg CPG_MOD R9A07G044_SCI0_CLKP>; + clock-names = "fck"; + power-domains = <&cpg>; + resets = <&cpg R9A07G044_SCI0_RST>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,scif.yaml b/Documentation/devicetree/bindings/serial/renesas,scif.yaml new file mode 100644 index 000000000..52c094873 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,scif.yaml @@ -0,0 +1,197 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scif.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communication Interface with FIFO (SCIF) + +maintainers: + - Geert Uytterhoeven + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scif-r7s72100 # RZ/A1H + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r7s9210 # RZ/A2 + + - items: + - enum: + - renesas,scif-r8a7778 # R-Car M1 + - renesas,scif-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-scif # R-Car Gen1 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r8a7742 # RZ/G1H + - renesas,scif-r8a7743 # RZ/G1M + - renesas,scif-r8a7744 # RZ/G1N + - renesas,scif-r8a7745 # RZ/G1E + - renesas,scif-r8a77470 # RZ/G1C + - renesas,scif-r8a7790 # R-Car H2 + - renesas,scif-r8a7791 # R-Car M2-W + - renesas,scif-r8a7792 # R-Car V2H + - renesas,scif-r8a7793 # R-Car M2-N + - renesas,scif-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-scif # R-Car Gen2 and RZ/G1 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r8a774a1 # RZ/G2M + - renesas,scif-r8a774b1 # RZ/G2N + - renesas,scif-r8a774c0 # RZ/G2E + - renesas,scif-r8a774e1 # RZ/G2H + - renesas,scif-r8a7795 # R-Car H3 + - renesas,scif-r8a7796 # R-Car M3-W + - renesas,scif-r8a77961 # R-Car M3-W+ + - renesas,scif-r8a77965 # R-Car M3-N + - renesas,scif-r8a77970 # R-Car V3M + - renesas,scif-r8a77980 # R-Car V3H + - renesas,scif-r8a77990 # R-Car E3 + - renesas,scif-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-scif # R-Car Gen3 and RZ/G2 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r8a779a0 # R-Car V3U + - renesas,scif-r8a779f0 # R-Car S4-8 + - const: renesas,rcar-gen4-scif # R-Car Gen4 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r9a07g044 # RZ/G2{L,LC} + + - items: + - enum: + - renesas,scif-r9a07g043 # RZ/G2UL and RZ/Five + - renesas,scif-r9a07g054 # RZ/V2L + - const: renesas,scif-r9a07g044 # RZ/G2{L,LC} fallback + + reg: + maxItems: 1 + + interrupts: + oneOf: + - items: + - description: A combined interrupt + - items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Break interrupt + - items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Break interrupt + - description: Data Ready interrupt + - description: Transmit End interrupt + + interrupt-names: + oneOf: + - items: + - const: eri + - const: rxi + - const: txi + - const: bri + - items: + - const: eri + - const: rxi + - const: txi + - const: bri + - const: dri + - const: tei + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + enum: + - fck # UART functional clock + - sck # optional external clock input + - brg_int # optional internal clock source for BRG frequency divider + - scif_clk # optional external clock source for BRG frequency divider + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scif + - renesas,rcar-gen3-scif + - renesas,rcar-gen4-scif + - renesas,scif-r9a07g044 +then: + required: + - resets + +unevaluatedProperties: false + +examples: + - | + #include + #include + #include + aliases { + serial0 = &scif0; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a7791", "renesas,rcar-gen2-scif", + "renesas,scif"; + reg = <0xe6e60000 64>; + interrupts = ; + clocks = <&cpg CPG_MOD 721>, <&cpg CPG_CORE R8A7791_CLK_ZS>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x29>, <&dmac0 0x2a>, <&dmac1 0x29>, <&dmac1 0x2a>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 721>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,scifa.yaml b/Documentation/devicetree/bindings/serial/renesas,scifa.yaml new file mode 100644 index 000000000..3c67d3202 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,scifa.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scifa.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communications Interface with FIFO A (SCIFA) + +maintainers: + - Geert Uytterhoeven + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scifa-r8a73a4 # R-Mobile APE6 + - renesas,scifa-r8a7740 # R-Mobile A1 + - renesas,scifa-sh73a0 # SH-Mobile AG5 + - const: renesas,scifa # generic SCIFA compatible UART + + - items: + - enum: + - renesas,scifa-r8a7742 # RZ/G1H + - renesas,scifa-r8a7743 # RZ/G1M + - renesas,scifa-r8a7744 # RZ/G1N + - renesas,scifa-r8a7745 # RZ/G1E + - renesas,scifa-r8a7790 # R-Car H2 + - renesas,scifa-r8a7791 # R-Car M2-W + - renesas,scifa-r8a7793 # R-Car M2-N + - renesas,scifa-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-scifa # R-Car Gen2 and RZ/G1 + - const: renesas,scifa # generic SCIFA compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + enum: + - fck # UART functional clock + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +unevaluatedProperties: false + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scifa +then: + required: + - resets + +examples: + - | + #include + #include + #include + aliases { + serial0 = &scifa0; + }; + + scifa0: serial@e6c40000 { + compatible = "renesas,scifa-r8a7790", "renesas,rcar-gen2-scifa", + "renesas,scifa"; + reg = <0xe6c40000 64>; + interrupts = ; + clocks = <&cpg CPG_MOD 204>; + clock-names = "fck"; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 204>; + dmas = <&dmac0 0x21>, <&dmac0 0x22>, <&dmac1 0x21>, <&dmac1 0x22>; + dma-names = "tx", "rx", "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,scifb.yaml b/Documentation/devicetree/bindings/serial/renesas,scifb.yaml new file mode 100644 index 000000000..d5571c7a4 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/renesas,scifb.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scifb.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communications Interface with FIFO B (SCIFB) + +maintainers: + - Geert Uytterhoeven + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scifb-r8a73a4 # R-Mobile APE6 + - renesas,scifb-r8a7740 # R-Mobile A1 + - renesas,scifb-sh73a0 # SH-Mobile AG5 + - const: renesas,scifb # generic SCIFB compatible UART + + - items: + - enum: + - renesas,scifb-r8a7742 # RZ/G1H + - renesas,scifb-r8a7743 # RZ/G1M + - renesas,scifb-r8a7744 # RZ/G1N + - renesas,scifb-r8a7745 # RZ/G1E + - renesas,scifb-r8a7790 # R-Car H2 + - renesas,scifb-r8a7791 # R-Car M2-W + - renesas,scifb-r8a7793 # R-Car M2-N + - renesas,scifb-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-scifb # R-Car Gen2 and RZ/G1 + - const: renesas,scifb # generic SCIFB compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + enum: + - fck # UART functional clock + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +unevaluatedProperties: false + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scifb +then: + required: + - resets + +examples: + - | + #include + #include + scifb: serial@e6c30000 { + compatible = "renesas,scifb-r8a7740", "renesas,scifb"; + reg = <0xe6c30000 0x100>; + interrupts = ; + clocks = <&mstp2_clks R8A7740_CLK_SCIFB>; + clock-names = "fck"; + power-domains = <&pd_a3sp>; + }; diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt new file mode 100644 index 000000000..a7fe93efc --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -0,0 +1 @@ +See rs485.yaml diff --git a/Documentation/devicetree/bindings/serial/rs485.yaml b/Documentation/devicetree/bindings/serial/rs485.yaml new file mode 100644 index 000000000..90a1bab40 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rs485.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/rs485.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RS485 serial communications Bindings + +description: The RTS signal is capable of automatically controlling line + direction for the built-in half-duplex mode. The properties described + hereafter shall be given to a half-duplex capable UART node. + +maintainers: + - Rob Herring + +properties: + rs485-rts-delay: + description: prop-encoded-array + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + items: + - description: Delay between rts signal and beginning of data sent in + milliseconds. It corresponds to the delay before sending data. + default: 0 + maximum: 100 + - description: Delay between end of data sent and rts signal in milliseconds. + It corresponds to the delay after sending data and actual release + of the line. + default: 0 + maximum: 100 + + rs485-rts-active-low: + description: drive RTS low when sending (default is high). + $ref: /schemas/types.yaml#/definitions/flag + + rs485-rx-active-high: + description: Polarity of receiver enable signal (when separate from RTS). + True indicates active high (default is low). + $ref: /schemas/types.yaml#/definitions/flag + + linux,rs485-enabled-at-boot-time: + description: enables the rs485 feature at boot time. It can be disabled + later with proper ioctl. + $ref: /schemas/types.yaml#/definitions/flag + + rs485-rx-during-tx: + description: enables the receiving of data even while sending data. + $ref: /schemas/types.yaml#/definitions/flag + + rs485-term-gpios: + description: GPIO pin to enable RS485 bus termination. + maxItems: 1 + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.yaml b/Documentation/devicetree/bindings/serial/samsung_uart.yaml new file mode 100644 index 000000000..8bd88d5cb --- /dev/null +++ b/Documentation/devicetree/bindings/serial/samsung_uart.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/samsung_uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S3C, S5P, Exynos, and S5L (Apple SoC) SoC UART Controller + +maintainers: + - Krzysztof Kozlowski + - Greg Kroah-Hartman + +description: |+ + Each Samsung UART should have an alias correctly numbered in the "aliases" + node, according to serialN format, where N is the port number (non-negative + decimal integer) as specified by User's Manual of respective SoC. + +properties: + compatible: + oneOf: + - items: + - const: samsung,exynosautov9-uart + - const: samsung,exynos850-uart + - enum: + - apple,s5l-uart + - axis,artpec8-uart + - samsung,s3c2410-uart + - samsung,s3c2412-uart + - samsung,s3c2440-uart + - samsung,s3c6400-uart + - samsung,s5pv210-uart + - samsung,exynos4210-uart + - samsung,exynos5433-uart + - samsung,exynos850-uart + + reg: + maxItems: 1 + + reg-io-width: + description: | + The size (in bytes) of the IO accesses that should be performed + on the device. + enum: [ 1, 4 ] + + clocks: + minItems: 2 + maxItems: 5 + + clock-names: + description: N = 0 is allowed for SoCs without internal baud clock mux. + minItems: 2 + items: + - const: uart + - pattern: '^clk_uart_baud[0-3]$' + - pattern: '^clk_uart_baud[0-3]$' + - pattern: '^clk_uart_baud[0-3]$' + - pattern: '^clk_uart_baud[0-3]$' + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + + interrupts: + description: RX interrupt and optionally TX interrupt. + minItems: 1 + maxItems: 2 + + power-domains: + maxItems: 1 + + samsung,uart-fifosize: + description: The fifo size supported by the UART channel. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [16, 64, 256] + +required: + - compatible + - clocks + - clock-names + - interrupts + - reg + +unevaluatedProperties: false + +allOf: + - $ref: serial.yaml# + + - if: + properties: + compatible: + contains: + enum: + - samsung,s3c2410-uart + - samsung,s5pv210-uart + then: + properties: + clocks: + minItems: 2 + maxItems: 3 + clock-names: + minItems: 2 + items: + - const: uart + - pattern: '^clk_uart_baud[0-1]$' + - pattern: '^clk_uart_baud[0-1]$' + + - if: + properties: + compatible: + contains: + enum: + - apple,s5l-uart + - axis,artpec8-uart + - samsung,exynos4210-uart + - samsung,exynos5433-uart + then: + properties: + clocks: + maxItems: 2 + clock-names: + items: + - const: uart + - const: clk_uart_baud0 + +examples: + - | + #include + + uart0: serial@7f005000 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <5>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + samsung,uart-fifosize = <16>; + }; diff --git a/Documentation/devicetree/bindings/serial/serial.yaml b/Documentation/devicetree/bindings/serial/serial.yaml new file mode 100644 index 000000000..c75ba3fb6 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/serial.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/serial.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Serial Interface Generic DT Bindings + +maintainers: + - Rob Herring + - Greg Kroah-Hartman + +description: + This document lists a set of generic properties for describing UARTs in a + device tree. Whether these properties apply to a particular device depends + on the DT bindings for the actual device. + + Each enabled UART may have an optional "serialN" alias in the "aliases" node, + where N is the port number (non-negative decimal integer) as printed on the + label next to the physical port. + +properties: + $nodename: + pattern: "^serial(@.*)?$" + + label: true + + cts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's CTS line. + + dcd-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DCD line. + + dsr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DSR line. + + dtr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DTR line. + + rng-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RNG line. + + rts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RTS line. + + uart-has-rtscts: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the UART has dedicated lines + for RTS/CTS hardware flow control, and that they are available for use + (wired and enabled by pinmux configuration). This depends on both the + UART hardware and the board wiring. + + rx-tx-swap: + type: boolean + description: RX and TX pins are swapped. + + cts-rts-swap: + type: boolean + description: CTS and RTS pins are swapped. + + rx-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + RX FIFO threshold configuration (in bytes). + + tx-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + TX FIFO threshold configuration (in bytes). + +if: + required: + - uart-has-rtscts +then: + properties: + cts-gpios: false + rts-gpios: false + +patternProperties: + ".*": + if: + type: object + then: + description: + Serial attached devices shall be a child node of the host UART device + the slave device is attached to. It is expected that the attached + device is the only child node of the UART device. The slave device node + name shall reflect the generic type of device for the node. + + properties: + compatible: + description: + Compatible of the device connected to the serial port. + + max-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The maximum baud rate the device operates at. + This should only be present if the maximum is less than the slave + device can support. For example, a particular board has some + signal quality issue or the host processor can't support higher + baud rates. + + current-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The current baud rate the device operates at. + This should only be present in case a driver has no chance to know + the baud rate of the slave device. + Examples: + * device supports auto-baud + * the rate is setup by a bootloader and there is no way to reset + the device + * device baud rate is configured by its firmware but there is no + way to request the actual settings + + required: + - compatible + +additionalProperties: true + +examples: + - | + serial@1234 { + compatible = "ns16550a"; + reg = <0x1234 0x20>; + interrupts = <1>; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + interrupt-parent = <&gpio>; + interrupts = <10>; + }; + }; diff --git a/Documentation/devicetree/bindings/serial/sifive-serial.yaml b/Documentation/devicetree/bindings/serial/sifive-serial.yaml new file mode 100644 index 000000000..b0a8871e3 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sifive-serial.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/sifive-serial.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive asynchronous serial interface (UART) + +maintainers: + - Pragnesh Patel + - Paul Walmsley + - Palmer Dabbelt + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + items: + - enum: + - sifive,fu540-c000-uart + - sifive,fu740-c000-uart + - canaan,k210-uarths + - const: sifive,uart0 + + description: + Should be something similar to "sifive,-uart" + for the UART as integrated on a particular chip, + and "sifive,uart" for the general UART IP + block programming model. + + UART HDL that corresponds to the IP block version + numbers can be found here - + + https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include + serial@10010000 { + compatible = "sifive,fu540-c000-uart", "sifive,uart0"; + interrupt-parent = <&plic0>; + interrupts = <80>; + reg = <0x10010000 0x1000>; + clocks = <&prci FU540_PRCI_CLK_TLCLK>; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml new file mode 100644 index 000000000..b9c2287c5 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare ABP UART + +maintainers: + - Rob Herring + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a06g032-uart + - renesas,r9a06g033-uart + - const: renesas,rzn1-uart + - items: + - enum: + - rockchip,px30-uart + - rockchip,rk1808-uart + - rockchip,rk3036-uart + - rockchip,rk3066-uart + - rockchip,rk3128-uart + - rockchip,rk3188-uart + - rockchip,rk3288-uart + - rockchip,rk3308-uart + - rockchip,rk3328-uart + - rockchip,rk3368-uart + - rockchip,rk3399-uart + - rockchip,rk3568-uart + - rockchip,rk3588-uart + - rockchip,rv1108-uart + - rockchip,rv1126-uart + - const: snps,dw-apb-uart + - items: + - enum: + - brcm,bcm11351-dw-apb-uart + - brcm,bcm21664-dw-apb-uart + - const: snps,dw-apb-uart + - items: + - enum: + - starfive,jh7100-hsuart + - starfive,jh7100-uart + - const: snps,dw-apb-uart + - const: snps,dw-apb-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: true + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: baudclk + - const: apb_pclk + + snps,uart-16550-compatible: + description: reflects the value of UART_16550_COMPATIBLE configuration + parameter. Define this if your UART does not implement the busy functionality. + type: boolean + + resets: + maxItems: 1 + + reg-shift: true + + reg-io-width: true + + dcd-override: + description: Override the DCD modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + dsr-override: + description: Override the DTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + cts-override: + description: Override the CTS modem status signal. This signal will + always be reported as active instead of being obtained from the modem + status register. Define this if your serial port does not use this + pin. + type: boolean + + ri-override: + description: Override the RI modem status signal. This signal will always + be reported as inactive instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. + type: boolean + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; + }; + + - | + // Example with one clock: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + - | + // Example with two clocks: + serial@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; +... diff --git a/Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml b/Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml new file mode 100644 index 000000000..3d01cc355 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/socionext,uniphier-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier UART controller + +maintainers: + - Masahiro Yamada + +properties: + compatible: + const: socionext,uniphier-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + auto-flow-control: + description: enable automatic flow control support. + $ref: /schemas/types.yaml#/definitions/flag + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + aliases { + serial0 = &serial0; + }; + + serial0: serial@54006800 { + compatible = "socionext,uniphier-uart"; + reg = <0x54006800 0x40>; + interrupts = <0 33 4>; + clocks = <&uart_clk>; + }; diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.yaml b/Documentation/devicetree/bindings/serial/sprd-uart.yaml new file mode 100644 index 000000000..da0e2745b --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sprd-uart.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2019 Unisoc Inc. +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/sprd-uart.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Spreadtrum serial UART + +maintainers: + - Orson Zhai + - Baolin Wang + - Chunyan Zhang + +properties: + compatible: + oneOf: + - items: + - enum: + - sprd,sc9860-uart + - sprd,sc9863a-uart + - sprd,ums512-uart + - const: sprd,sc9836-uart + - const: sprd,sc9836-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + description: | + "enable" for UART module enable clock, "uart" for UART clock, "source" + for UART source (parent) clock. + items: + - const: enable + - const: uart + - const: source + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + items: + - const: rx + - const: tx + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include + serial@0 { + compatible = "sprd,sc9860-uart", "sprd,sc9836-uart"; + reg = <0x0 0x100>; + interrupts = ; + dma-names = "rx", "tx"; + dmas = <&ap_dma 19>, <&ap_dma 20>; + clock-names = "enable", "uart", "source"; + clocks = <&clk_ap_apb_gates 9>, <&clk_uart0>, <&ext_26m>; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml new file mode 100644 index 000000000..333dc4272 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/st,stm32-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +maintainers: + - Erwan Le Ray + +title: STMicroelectronics STM32 USART bindings + +properties: + compatible: + enum: + - st,stm32-uart + - st,stm32f7-uart + - st,stm32h7-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + label: + description: label associated with this uart + + st,hw-flow-ctrl: + description: enable hardware flow control (deprecated) + $ref: /schemas/types.yaml#/definitions/flag + + uart-has-rtscts: true + + rx-tx-swap: true + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + items: + enum: [ rx, tx ] + minItems: 1 + maxItems: 2 + +# cts-gpios and rts-gpios properties can be used instead of 'uart-has-rtscts' +# or 'st,hw-flow-ctrl' (deprecated) for making use of any gpio pins for flow +# control instead of dedicated pins. +# +# It should be noted that both cts-gpios/rts-gpios and 'uart-has-rtscts' or +# 'st,hw-flow-ctrl' (deprecated) properties cannot co-exist in a design. + cts-gpios: true + rts-gpios: true + + wakeup-source: true + + rs485-rts-delay: true + rs485-rts-active-low: true + linux,rs485-enabled-at-boot-time: true + rs485-rx-during-tx: true + + rx-threshold: + description: + If value is set to 1, RX FIFO threshold is disabled. + enum: [1, 2, 4, 8, 12, 14, 16] + default: 8 + + tx-threshold: + description: + If value is set to 1, TX FIFO threshold is disabled. + enum: [1, 2, 4, 8, 12, 14, 16] + default: 8 + +allOf: + - $ref: rs485.yaml# + - $ref: serial.yaml# + - if: + required: + - st,hw-flow-ctrl + then: + properties: + cts-gpios: false + rts-gpios: false + - if: + properties: + compatible: + const: st,stm32-uart + then: + properties: + rx-tx-swap: false + - if: + properties: + compatible: + contains: + enum: + - st,stm32-uart + - st,stm32f7-uart + then: + properties: + rx-threshold: false + tx-threshold: false + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include + usart1: serial@40011000 { + compatible = "st,stm32h7-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 164>; + dmas = <&dma2 2 4 0x414 0x0>, + <&dma2 7 4 0x414 0x0>; + dma-names = "rx", "tx"; + rx-threshold = <4>; + tx-threshold = <4>; + rs485-rts-active-low; + }; + +... diff --git a/Documentation/devicetree/bindings/serial/st-asc.txt b/Documentation/devicetree/bindings/serial/st-asc.txt new file mode 100644 index 000000000..75d877f59 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st-asc.txt @@ -0,0 +1,18 @@ +*st-asc(Serial Port) + +Required properties: +- compatible : Should be "st,asc". +- reg, reg-names, interrupts, interrupt-names : Standard way to define device + resources with names. look in + Documentation/devicetree/bindings/resource-names.txt + +Optional properties: +- st,hw-flow-ctrl bool flag to enable hardware flow control. +- st,force-m1 bool flat to force asc to be in Mode-1 recommeded + for high bit rates (above 19.2K) +Example: +serial@fe440000{ + compatible = "st,asc"; + reg = <0xfe440000 0x2c>; + interrupts = <0 209 0>; +}; diff --git a/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml new file mode 100644 index 000000000..ea1e63766 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) Sunplus Co., Ltd. 2021 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/sunplus,sp7021-uart.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Sunplus SoC SP7021 UART Controller + +maintainers: + - Hammer Hsieh + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + const: sunplus,sp7021-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +additionalProperties: false + +examples: + - | + #include + aliases { + serial0 = &uart0; + }; + + uart0: serial@9c000900 { + compatible = "sunplus,sp7021-uart"; + reg = <0x9c000900 0x80>; + interrupt-parent = <&intc>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkc 0x28>; + resets = <&rstc 0x18>; + }; +... diff --git a/Documentation/devicetree/bindings/serial/vt8500-uart.txt b/Documentation/devicetree/bindings/serial/vt8500-uart.txt new file mode 100644 index 000000000..2b64e6107 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/vt8500-uart.txt @@ -0,0 +1,27 @@ +* VIA VT8500 and WonderMedia WM8xxx UART Controller + +Required properties: +- compatible: should be "via,vt8500-uart" (for VIA/WonderMedia chips up to and + including WM8850/WM8950), or "wm,wm8880-uart" (for WM8880 and later) + +- reg: base physical address of the controller and length of memory mapped + region. + +- interrupts: hardware interrupt number + +- clocks: shall be the input parent clock phandle for the clock. This should + be the 24Mhz reference clock. + +Aliases may be defined to ensure the correct ordering of the uarts. + +Example: + aliases { + serial0 = &uart0; + }; + + uart0: serial@d8200000 { + compatible = "via,vt8500-uart"; + reg = <0xd8200000 0x1040>; + interrupts = <32>; + clocks = <&clkuart0>; + }; diff --git a/Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml b/Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml new file mode 100644 index 000000000..f7617b88c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/xlnx,opb-uartlite.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/xlnx,opb-uartlite.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx Axi Uartlite + +maintainers: + - Peter Korsgaard + +properties: + compatible: + contains: + enum: + - xlnx,xps-uartlite-1.00.a + - xlnx,opb-uartlite-1.00.b + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + port-number: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Set Uart port number + + clocks: + maxItems: 1 + + clock-names: + const: s_axi_aclk + + current-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The fixed baud rate that the device was configured for. + + xlnx,data-bits: + enum: [5, 6, 7, 8] + description: + The fixed number of data bits that the device was configured for. + + xlnx,use-parity: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + Whether parity checking was enabled when the device was configured. + + xlnx,odd-parity: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + Whether odd parity was configured. + +required: + - compatible + - reg + - interrupts + - current-speed + - xlnx,data-bits + - xlnx,use-parity + +allOf: + - $ref: /schemas/serial.yaml# + - if: + properties: + xlnx,use-parity: + contains: + const: 1 + then: + required: + - xlnx,odd-parity + +unevaluatedProperties: false + +examples: + - | + serial@800c0000 { + compatible = "xlnx,xps-uartlite-1.00.a"; + reg = <0x800c0000 0x10000>; + interrupts = <0x0 0x6e 0x1>; + port-number = <0>; + current-speed = <115200>; + xlnx,data-bits = <8>; + xlnx,use-parity = <0>; + }; +... -- cgit v1.2.3