From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../driver-api/media/drivers/cpia2_devel.rst | 56 ++++++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/driver-api/media/drivers/cpia2_devel.rst (limited to 'Documentation/driver-api/media/drivers/cpia2_devel.rst') diff --git a/Documentation/driver-api/media/drivers/cpia2_devel.rst b/Documentation/driver-api/media/drivers/cpia2_devel.rst new file mode 100644 index 000000000..decaa4768 --- /dev/null +++ b/Documentation/driver-api/media/drivers/cpia2_devel.rst @@ -0,0 +1,56 @@ +.. SPDX-License-Identifier: GPL-2.0 + +The cpia2 driver +================ + +Authors: Peter Pregler , +Scott J. Bertin , and +Jarl Totland for the original cpia driver, which +this one was modelled from. + + +Notes to developers +~~~~~~~~~~~~~~~~~~~ + + - This is a driver version stripped of the 2.4 back compatibility + and old MJPEG ioctl API. See cpia2.sf.net for 2.4 support. + +Programmer's overview of cpia2 driver +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Cpia2 is the second generation video coprocessor from VLSI Vision Ltd (now a +division of ST Microelectronics). There are two versions. The first is the +STV0672, which is capable of up to 30 frames per second (fps) in frame sizes +up to CIF, and 15 fps for VGA frames. The STV0676 is an improved version, +which can handle up to 30 fps VGA. Both coprocessors can be attached to two +CMOS sensors - the vvl6410 CIF sensor and the vvl6500 VGA sensor. These will +be referred to as the 410 and the 500 sensors, or the CIF and VGA sensors. + +The two chipsets operate almost identically. The core is an 8051 processor, +running two different versions of firmware. The 672 runs the VP4 video +processor code, the 676 runs VP5. There are a few differences in register +mappings for the two chips. In these cases, the symbols defined in the +header files are marked with VP4 or VP5 as part of the symbol name. + +The cameras appear externally as three sets of registers. Setting register +values is the only way to control the camera. Some settings are +interdependant, such as the sequence required to power up the camera. I will +try to make note of all of these cases. + +The register sets are called blocks. Block 0 is the system block. This +section is always powered on when the camera is plugged in. It contains +registers that control housekeeping functions such as powering up the video +processor. The video processor is the VP block. These registers control +how the video from the sensor is processed. Examples are timing registers, +user mode (vga, qvga), scaling, cropping, framerates, and so on. The last +block is the video compressor (VC). The video stream sent from the camera is +compressed as Motion JPEG (JPEGA). The VC controls all of the compression +parameters. Looking at the file cpia2_registers.h, you can get a full view +of these registers and the possible values for most of them. + +One or more registers can be set or read by sending a usb control message to +the camera. There are three modes for this. Block mode requests a number +of contiguous registers. Random mode reads or writes random registers with +a tuple structure containing address/value pairs. The repeat mode is only +used by VP4 to load a firmware patch. It contains a starting address and +a sequence of bytes to be written into a gpio port. -- cgit v1.2.3