From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- drivers/gpu/drm/bridge/sii9234.c | 970 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 970 insertions(+) create mode 100644 drivers/gpu/drm/bridge/sii9234.c (limited to 'drivers/gpu/drm/bridge/sii9234.c') diff --git a/drivers/gpu/drm/bridge/sii9234.c b/drivers/gpu/drm/bridge/sii9234.c new file mode 100644 index 000000000..5b3061d4b --- /dev/null +++ b/drivers/gpu/drm/bridge/sii9234.c @@ -0,0 +1,970 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2017 Samsung Electronics + * + * Authors: + * Tomasz Stanislawski + * Maciej Purski + * + * Based on sii9234 driver created by: + * Adam Hampson + * Erik Gilling + * Shankar Bandal + * Dharam Kumar + */ +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define CBUS_DEVCAP_OFFSET 0x80 + +#define SII9234_MHL_VERSION 0x11 +#define SII9234_SCRATCHPAD_SIZE 0x10 +#define SII9234_INT_STAT_SIZE 0x33 + +#define BIT_TMDS_CCTRL_TMDS_OE BIT(4) +#define MHL_HPD_OUT_OVR_EN BIT(4) +#define MHL_HPD_OUT_OVR_VAL BIT(5) +#define MHL_INIT_TIMEOUT 0x0C + +/* MHL Tx registers and bits */ +#define MHL_TX_SRST 0x05 +#define MHL_TX_SYSSTAT_REG 0x09 +#define MHL_TX_INTR1_REG 0x71 +#define MHL_TX_INTR4_REG 0x74 +#define MHL_TX_INTR1_ENABLE_REG 0x75 +#define MHL_TX_INTR4_ENABLE_REG 0x78 +#define MHL_TX_INT_CTRL_REG 0x79 +#define MHL_TX_TMDS_CCTRL 0x80 +#define MHL_TX_DISC_CTRL1_REG 0x90 +#define MHL_TX_DISC_CTRL2_REG 0x91 +#define MHL_TX_DISC_CTRL3_REG 0x92 +#define MHL_TX_DISC_CTRL4_REG 0x93 +#define MHL_TX_DISC_CTRL5_REG 0x94 +#define MHL_TX_DISC_CTRL6_REG 0x95 +#define MHL_TX_DISC_CTRL7_REG 0x96 +#define MHL_TX_DISC_CTRL8_REG 0x97 +#define MHL_TX_STAT2_REG 0x99 +#define MHL_TX_MHLTX_CTL1_REG 0xA0 +#define MHL_TX_MHLTX_CTL2_REG 0xA1 +#define MHL_TX_MHLTX_CTL4_REG 0xA3 +#define MHL_TX_MHLTX_CTL6_REG 0xA5 +#define MHL_TX_MHLTX_CTL7_REG 0xA6 + +#define RSEN_STATUS BIT(2) +#define HPD_CHANGE_INT BIT(6) +#define RSEN_CHANGE_INT BIT(5) +#define RGND_READY_INT BIT(6) +#define VBUS_LOW_INT BIT(5) +#define CBUS_LKOUT_INT BIT(4) +#define MHL_DISC_FAIL_INT BIT(3) +#define MHL_EST_INT BIT(2) +#define HPD_CHANGE_INT_MASK BIT(6) +#define RSEN_CHANGE_INT_MASK BIT(5) + +#define RGND_READY_MASK BIT(6) +#define CBUS_LKOUT_MASK BIT(4) +#define MHL_DISC_FAIL_MASK BIT(3) +#define MHL_EST_MASK BIT(2) + +#define SKIP_GND BIT(6) + +#define ATT_THRESH_SHIFT 0x04 +#define ATT_THRESH_MASK (0x03 << ATT_THRESH_SHIFT) +#define USB_D_OEN BIT(3) +#define DEGLITCH_TIME_MASK 0x07 +#define DEGLITCH_TIME_2MS 0 +#define DEGLITCH_TIME_4MS 1 +#define DEGLITCH_TIME_8MS 2 +#define DEGLITCH_TIME_16MS 3 +#define DEGLITCH_TIME_40MS 4 +#define DEGLITCH_TIME_50MS 5 +#define DEGLITCH_TIME_60MS 6 +#define DEGLITCH_TIME_128MS 7 + +#define USB_D_OVR BIT(7) +#define USB_ID_OVR BIT(6) +#define DVRFLT_SEL BIT(5) +#define BLOCK_RGND_INT BIT(4) +#define SKIP_DEG BIT(3) +#define CI2CA_POL BIT(2) +#define CI2CA_WKUP BIT(1) +#define SINGLE_ATT BIT(0) + +#define USB_D_ODN BIT(5) +#define VBUS_CHECK BIT(2) +#define RGND_INTP_MASK 0x03 +#define RGND_INTP_OPEN 0 +#define RGND_INTP_2K 1 +#define RGND_INTP_1K 2 +#define RGND_INTP_SHORT 3 + +/* HDMI registers */ +#define HDMI_RX_TMDS0_CCTRL1_REG 0x10 +#define HDMI_RX_TMDS_CLK_EN_REG 0x11 +#define HDMI_RX_TMDS_CH_EN_REG 0x12 +#define HDMI_RX_PLL_CALREFSEL_REG 0x17 +#define HDMI_RX_PLL_VCOCAL_REG 0x1A +#define HDMI_RX_EQ_DATA0_REG 0x22 +#define HDMI_RX_EQ_DATA1_REG 0x23 +#define HDMI_RX_EQ_DATA2_REG 0x24 +#define HDMI_RX_EQ_DATA3_REG 0x25 +#define HDMI_RX_EQ_DATA4_REG 0x26 +#define HDMI_RX_TMDS_ZONE_CTRL_REG 0x4C +#define HDMI_RX_TMDS_MODE_CTRL_REG 0x4D + +/* CBUS registers */ +#define CBUS_INT_STATUS_1_REG 0x08 +#define CBUS_INTR1_ENABLE_REG 0x09 +#define CBUS_MSC_REQ_ABORT_REASON_REG 0x0D +#define CBUS_INT_STATUS_2_REG 0x1E +#define CBUS_INTR2_ENABLE_REG 0x1F +#define CBUS_LINK_CONTROL_2_REG 0x31 +#define CBUS_MHL_STATUS_REG_0 0xB0 +#define CBUS_MHL_STATUS_REG_1 0xB1 + +#define BIT_CBUS_RESET BIT(3) +#define SET_HPD_DOWNSTREAM BIT(6) + +/* TPI registers */ +#define TPI_DPD_REG 0x3D + +/* Timeouts in msec */ +#define T_SRC_VBUS_CBUS_TO_STABLE 200 +#define T_SRC_CBUS_FLOAT 100 +#define T_SRC_CBUS_DEGLITCH 2 +#define T_SRC_RXSENSE_DEGLITCH 110 + +#define MHL1_MAX_CLK 75000 /* in kHz */ + +#define I2C_TPI_ADDR 0x3D +#define I2C_HDMI_ADDR 0x49 +#define I2C_CBUS_ADDR 0x64 + +enum sii9234_state { + ST_OFF, + ST_D3, + ST_RGND_INIT, + ST_RGND_1K, + ST_RSEN_HIGH, + ST_MHL_ESTABLISHED, + ST_FAILURE_DISCOVERY, + ST_FAILURE, +}; + +struct sii9234 { + struct i2c_client *client[4]; + struct drm_bridge bridge; + struct device *dev; + struct gpio_desc *gpio_reset; + int i2c_error; + struct regulator_bulk_data supplies[4]; + + struct mutex lock; /* Protects fields below and device registers */ + enum sii9234_state state; +}; + +enum sii9234_client_id { + I2C_MHL, + I2C_TPI, + I2C_HDMI, + I2C_CBUS, +}; + +static const char * const sii9234_client_name[] = { + [I2C_MHL] = "MHL", + [I2C_TPI] = "TPI", + [I2C_HDMI] = "HDMI", + [I2C_CBUS] = "CBUS", +}; + +static int sii9234_writeb(struct sii9234 *ctx, int id, int offset, + int value) +{ + int ret; + struct i2c_client *client = ctx->client[id]; + + if (ctx->i2c_error) + return ctx->i2c_error; + + ret = i2c_smbus_write_byte_data(client, offset, value); + if (ret < 0) + dev_err(ctx->dev, "writeb: %4s[0x%02x] <- 0x%02x\n", + sii9234_client_name[id], offset, value); + ctx->i2c_error = ret; + + return ret; +} + +static int sii9234_writebm(struct sii9234 *ctx, int id, int offset, + int value, int mask) +{ + int ret; + struct i2c_client *client = ctx->client[id]; + + if (ctx->i2c_error) + return ctx->i2c_error; + + ret = i2c_smbus_write_byte(client, offset); + if (ret < 0) { + dev_err(ctx->dev, "writebm: %4s[0x%02x] <- 0x%02x\n", + sii9234_client_name[id], offset, value); + ctx->i2c_error = ret; + return ret; + } + + ret = i2c_smbus_read_byte(client); + if (ret < 0) { + dev_err(ctx->dev, "writebm: %4s[0x%02x] <- 0x%02x\n", + sii9234_client_name[id], offset, value); + ctx->i2c_error = ret; + return ret; + } + + value = (value & mask) | (ret & ~mask); + + ret = i2c_smbus_write_byte_data(client, offset, value); + if (ret < 0) { + dev_err(ctx->dev, "writebm: %4s[0x%02x] <- 0x%02x\n", + sii9234_client_name[id], offset, value); + ctx->i2c_error = ret; + } + + return ret; +} + +static int sii9234_readb(struct sii9234 *ctx, int id, int offset) +{ + int ret; + struct i2c_client *client = ctx->client[id]; + + if (ctx->i2c_error) + return ctx->i2c_error; + + ret = i2c_smbus_write_byte(client, offset); + if (ret < 0) { + dev_err(ctx->dev, "readb: %4s[0x%02x]\n", + sii9234_client_name[id], offset); + ctx->i2c_error = ret; + return ret; + } + + ret = i2c_smbus_read_byte(client); + if (ret < 0) { + dev_err(ctx->dev, "readb: %4s[0x%02x]\n", + sii9234_client_name[id], offset); + ctx->i2c_error = ret; + } + + return ret; +} + +static int sii9234_clear_error(struct sii9234 *ctx) +{ + int ret = ctx->i2c_error; + + ctx->i2c_error = 0; + + return ret; +} + +#define mhl_tx_writeb(sii9234, offset, value) \ + sii9234_writeb(sii9234, I2C_MHL, offset, value) +#define mhl_tx_writebm(sii9234, offset, value, mask) \ + sii9234_writebm(sii9234, I2C_MHL, offset, value, mask) +#define mhl_tx_readb(sii9234, offset) \ + sii9234_readb(sii9234, I2C_MHL, offset) +#define cbus_writeb(sii9234, offset, value) \ + sii9234_writeb(sii9234, I2C_CBUS, offset, value) +#define cbus_writebm(sii9234, offset, value, mask) \ + sii9234_writebm(sii9234, I2C_CBUS, offset, value, mask) +#define cbus_readb(sii9234, offset) \ + sii9234_readb(sii9234, I2C_CBUS, offset) +#define hdmi_writeb(sii9234, offset, value) \ + sii9234_writeb(sii9234, I2C_HDMI, offset, value) +#define hdmi_writebm(sii9234, offset, value, mask) \ + sii9234_writebm(sii9234, I2C_HDMI, offset, value, mask) +#define hdmi_readb(sii9234, offset) \ + sii9234_readb(sii9234, I2C_HDMI, offset) +#define tpi_writeb(sii9234, offset, value) \ + sii9234_writeb(sii9234, I2C_TPI, offset, value) +#define tpi_writebm(sii9234, offset, value, mask) \ + sii9234_writebm(sii9234, I2C_TPI, offset, value, mask) +#define tpi_readb(sii9234, offset) \ + sii9234_readb(sii9234, I2C_TPI, offset) + +static u8 sii9234_tmds_control(struct sii9234 *ctx, bool enable) +{ + mhl_tx_writebm(ctx, MHL_TX_TMDS_CCTRL, enable ? ~0 : 0, + BIT_TMDS_CCTRL_TMDS_OE); + mhl_tx_writebm(ctx, MHL_TX_INT_CTRL_REG, enable ? ~0 : 0, + MHL_HPD_OUT_OVR_EN | MHL_HPD_OUT_OVR_VAL); + return sii9234_clear_error(ctx); +} + +static int sii9234_cbus_reset(struct sii9234 *ctx) +{ + int i; + + mhl_tx_writebm(ctx, MHL_TX_SRST, ~0, BIT_CBUS_RESET); + msleep(T_SRC_CBUS_DEGLITCH); + mhl_tx_writebm(ctx, MHL_TX_SRST, 0, BIT_CBUS_RESET); + + for (i = 0; i < 4; i++) { + /* + * Enable WRITE_STAT interrupt for writes to all + * 4 MSC Status registers. + */ + cbus_writeb(ctx, 0xE0 + i, 0xF2); + /* + * Enable SET_INT interrupt for writes to all + * 4 MSC Interrupt registers. + */ + cbus_writeb(ctx, 0xF0 + i, 0xF2); + } + + return sii9234_clear_error(ctx); +} + +/* Require to chek mhl imformation of samsung in cbus_init_register */ +static int sii9234_cbus_init(struct sii9234 *ctx) +{ + cbus_writeb(ctx, 0x07, 0xF2); + cbus_writeb(ctx, 0x40, 0x03); + cbus_writeb(ctx, 0x42, 0x06); + cbus_writeb(ctx, 0x36, 0x0C); + cbus_writeb(ctx, 0x3D, 0xFD); + cbus_writeb(ctx, 0x1C, 0x01); + cbus_writeb(ctx, 0x1D, 0x0F); + cbus_writeb(ctx, 0x44, 0x02); + /* Setup our devcap */ + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_DEV_STATE, 0x00); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_MHL_VERSION, + SII9234_MHL_VERSION); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_CAT, + MHL_DCAP_CAT_SOURCE); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_ADOPTER_ID_H, 0x01); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_ADOPTER_ID_L, 0x41); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_VID_LINK_MODE, + MHL_DCAP_VID_LINK_RGB444 | MHL_DCAP_VID_LINK_YCBCR444); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_VIDEO_TYPE, + MHL_DCAP_VT_GRAPHICS); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_LOG_DEV_MAP, + MHL_DCAP_LD_GUI); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_BANDWIDTH, 0x0F); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_FEATURE_FLAG, + MHL_DCAP_FEATURE_RCP_SUPPORT | MHL_DCAP_FEATURE_RAP_SUPPORT + | MHL_DCAP_FEATURE_SP_SUPPORT); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_DEVICE_ID_H, 0x0); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_DEVICE_ID_L, 0x0); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_SCRATCHPAD_SIZE, + SII9234_SCRATCHPAD_SIZE); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_INT_STAT_SIZE, + SII9234_INT_STAT_SIZE); + cbus_writeb(ctx, CBUS_DEVCAP_OFFSET + MHL_DCAP_RESERVED, 0); + cbus_writebm(ctx, 0x31, 0x0C, 0x0C); + cbus_writeb(ctx, 0x30, 0x01); + cbus_writebm(ctx, 0x3C, 0x30, 0x38); + cbus_writebm(ctx, 0x22, 0x0D, 0x0F); + cbus_writebm(ctx, 0x2E, 0x15, 0x15); + cbus_writeb(ctx, CBUS_INTR1_ENABLE_REG, 0); + cbus_writeb(ctx, CBUS_INTR2_ENABLE_REG, 0); + + return sii9234_clear_error(ctx); +} + +static void force_usb_id_switch_open(struct sii9234 *ctx) +{ + /* Disable CBUS discovery */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL1_REG, 0, 0x01); + /* Force USB ID switch to open */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR); + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL3_REG, ~0, 0x86); + /* Force upstream HPD to 0 when not in MHL mode. */ + mhl_tx_writebm(ctx, MHL_TX_INT_CTRL_REG, 0, 0x30); +} + +static void release_usb_id_switch_open(struct sii9234 *ctx) +{ + msleep(T_SRC_CBUS_FLOAT); + /* Clear USB ID switch to open */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL6_REG, 0, USB_ID_OVR); + /* Enable CBUS discovery */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL1_REG, ~0, 0x01); +} + +static int sii9234_power_init(struct sii9234 *ctx) +{ + /* Force the SiI9234 into the D0 state. */ + tpi_writeb(ctx, TPI_DPD_REG, 0x3F); + /* Enable TxPLL Clock */ + hdmi_writeb(ctx, HDMI_RX_TMDS_CLK_EN_REG, 0x01); + /* Enable Tx Clock Path & Equalizer */ + hdmi_writeb(ctx, HDMI_RX_TMDS_CH_EN_REG, 0x15); + /* Power Up TMDS */ + mhl_tx_writeb(ctx, 0x08, 0x35); + return sii9234_clear_error(ctx); +} + +static int sii9234_hdmi_init(struct sii9234 *ctx) +{ + hdmi_writeb(ctx, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1); + hdmi_writeb(ctx, HDMI_RX_PLL_CALREFSEL_REG, 0x03); + hdmi_writeb(ctx, HDMI_RX_PLL_VCOCAL_REG, 0x20); + hdmi_writeb(ctx, HDMI_RX_EQ_DATA0_REG, 0x8A); + hdmi_writeb(ctx, HDMI_RX_EQ_DATA1_REG, 0x6A); + hdmi_writeb(ctx, HDMI_RX_EQ_DATA2_REG, 0xAA); + hdmi_writeb(ctx, HDMI_RX_EQ_DATA3_REG, 0xCA); + hdmi_writeb(ctx, HDMI_RX_EQ_DATA4_REG, 0xEA); + hdmi_writeb(ctx, HDMI_RX_TMDS_ZONE_CTRL_REG, 0xA0); + hdmi_writeb(ctx, HDMI_RX_TMDS_MODE_CTRL_REG, 0x00); + mhl_tx_writeb(ctx, MHL_TX_TMDS_CCTRL, 0x34); + hdmi_writeb(ctx, 0x45, 0x44); + hdmi_writeb(ctx, 0x31, 0x0A); + hdmi_writeb(ctx, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1); + + return sii9234_clear_error(ctx); +} + +static int sii9234_mhl_tx_ctl_int(struct sii9234 *ctx) +{ + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL1_REG, 0xD0); + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL2_REG, 0xFC); + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL4_REG, 0xEB); + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL7_REG, 0x0C); + + return sii9234_clear_error(ctx); +} + +static int sii9234_reset(struct sii9234 *ctx) +{ + int ret; + + sii9234_clear_error(ctx); + + ret = sii9234_power_init(ctx); + if (ret < 0) + return ret; + ret = sii9234_cbus_reset(ctx); + if (ret < 0) + return ret; + ret = sii9234_hdmi_init(ctx); + if (ret < 0) + return ret; + ret = sii9234_mhl_tx_ctl_int(ctx); + if (ret < 0) + return ret; + + /* Enable HDCP Compliance safety */ + mhl_tx_writeb(ctx, 0x2B, 0x01); + /* CBUS discovery cycle time for each drive and float = 150us */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL1_REG, 0x04, 0x06); + /* Clear bit 6 (reg_skip_rgnd) */ + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL2_REG, (1 << 7) /* Reserved */ + | 2 << ATT_THRESH_SHIFT | DEGLITCH_TIME_50MS); + /* + * Changed from 66 to 65 for 94[1:0] = 01 = 5k reg_cbusmhl_pup_sel + * 1.8V CBUS VTH & GND threshold + * to meet CTS 3.3.7.2 spec + */ + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL5_REG, 0x77); + cbus_writebm(ctx, CBUS_LINK_CONTROL_2_REG, ~0, MHL_INIT_TIMEOUT); + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL6_REG, 0xA0); + /* RGND & single discovery attempt (RGND blocking) */ + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL6_REG, BLOCK_RGND_INT | + DVRFLT_SEL | SINGLE_ATT); + /* Use VBUS path of discovery state machine */ + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL8_REG, 0); + /* 0x92[3] sets the CBUS / ID switch */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR); + /* + * To allow RGND engine to operate correctly. + * When moving the chip from D2 to D0 (power up, init regs) + * the values should be + * 94[1:0] = 01 reg_cbusmhl_pup_sel[1:0] should be set for 5k + * 93[7:6] = 10 reg_cbusdisc_pup_sel[1:0] should be + * set for 10k (default) + * 93[5:4] = 00 reg_cbusidle_pup_sel[1:0] = open (default) + */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL3_REG, ~0, 0x86); + /* + * Change from CC to 8C to match 5K + * to meet CTS 3.3.72 spec + */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C); + /* Configure the interrupt as active high */ + mhl_tx_writebm(ctx, MHL_TX_INT_CTRL_REG, 0, 0x06); + + msleep(25); + + /* Release usb_id switch */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL6_REG, 0, USB_ID_OVR); + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL1_REG, 0x27); + + ret = sii9234_clear_error(ctx); + if (ret < 0) + return ret; + ret = sii9234_cbus_init(ctx); + if (ret < 0) + return ret; + + /* Enable Auto soft reset on SCDT = 0 */ + mhl_tx_writeb(ctx, 0x05, 0x04); + /* HDMI Transcode mode enable */ + mhl_tx_writeb(ctx, 0x0D, 0x1C); + mhl_tx_writeb(ctx, MHL_TX_INTR4_ENABLE_REG, + RGND_READY_MASK | CBUS_LKOUT_MASK + | MHL_DISC_FAIL_MASK | MHL_EST_MASK); + mhl_tx_writeb(ctx, MHL_TX_INTR1_ENABLE_REG, 0x60); + + /* This point is very important before measure RGND impedance */ + force_usb_id_switch_open(ctx); + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL4_REG, 0, 0xF0); + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL5_REG, 0, 0x03); + release_usb_id_switch_open(ctx); + + /* Force upstream HPD to 0 when not in MHL mode */ + mhl_tx_writebm(ctx, MHL_TX_INT_CTRL_REG, 0, 1 << 5); + mhl_tx_writebm(ctx, MHL_TX_INT_CTRL_REG, ~0, 1 << 4); + + return sii9234_clear_error(ctx); +} + +static int sii9234_goto_d3(struct sii9234 *ctx) +{ + int ret; + + dev_dbg(ctx->dev, "sii9234: detection started d3\n"); + + ret = sii9234_reset(ctx); + if (ret < 0) + goto exit; + + hdmi_writeb(ctx, 0x01, 0x03); + tpi_writebm(ctx, TPI_DPD_REG, 0, 1); + /* I2C above is expected to fail because power goes down */ + sii9234_clear_error(ctx); + + ctx->state = ST_D3; + + return 0; + exit: + dev_err(ctx->dev, "%s failed\n", __func__); + return -1; +} + +static int sii9234_hw_on(struct sii9234 *ctx) +{ + return regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static void sii9234_hw_off(struct sii9234 *ctx) +{ + gpiod_set_value(ctx->gpio_reset, 1); + msleep(20); + regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); +} + +static void sii9234_hw_reset(struct sii9234 *ctx) +{ + gpiod_set_value(ctx->gpio_reset, 1); + msleep(20); + gpiod_set_value(ctx->gpio_reset, 0); +} + +static void sii9234_cable_in(struct sii9234 *ctx) +{ + int ret; + + mutex_lock(&ctx->lock); + if (ctx->state != ST_OFF) + goto unlock; + ret = sii9234_hw_on(ctx); + if (ret < 0) + goto unlock; + + sii9234_hw_reset(ctx); + sii9234_goto_d3(ctx); + /* To avoid irq storm, when hw is in meta state */ + enable_irq(to_i2c_client(ctx->dev)->irq); + +unlock: + mutex_unlock(&ctx->lock); +} + +static void sii9234_cable_out(struct sii9234 *ctx) +{ + mutex_lock(&ctx->lock); + + if (ctx->state == ST_OFF) + goto unlock; + + disable_irq(to_i2c_client(ctx->dev)->irq); + tpi_writeb(ctx, TPI_DPD_REG, 0); + /* Turn on&off hpd festure for only QCT HDMI */ + sii9234_hw_off(ctx); + + ctx->state = ST_OFF; + +unlock: + mutex_unlock(&ctx->lock); +} + +static enum sii9234_state sii9234_rgnd_ready_irq(struct sii9234 *ctx) +{ + int value; + + if (ctx->state == ST_D3) { + int ret; + + dev_dbg(ctx->dev, "RGND_READY_INT\n"); + sii9234_hw_reset(ctx); + + ret = sii9234_reset(ctx); + if (ret < 0) { + dev_err(ctx->dev, "sii9234_reset() failed\n"); + return ST_FAILURE; + } + + return ST_RGND_INIT; + } + + /* Got interrupt in inappropriate state */ + if (ctx->state != ST_RGND_INIT) + return ST_FAILURE; + + value = mhl_tx_readb(ctx, MHL_TX_STAT2_REG); + if (sii9234_clear_error(ctx)) + return ST_FAILURE; + + if ((value & RGND_INTP_MASK) != RGND_INTP_1K) { + dev_warn(ctx->dev, "RGND is not 1k\n"); + return ST_RGND_INIT; + } + dev_dbg(ctx->dev, "RGND 1K!!\n"); + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C); + mhl_tx_writeb(ctx, MHL_TX_DISC_CTRL5_REG, 0x77); + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL6_REG, ~0, 0x05); + if (sii9234_clear_error(ctx)) + return ST_FAILURE; + + msleep(T_SRC_VBUS_CBUS_TO_STABLE); + return ST_RGND_1K; +} + +static enum sii9234_state sii9234_mhl_established(struct sii9234 *ctx) +{ + dev_dbg(ctx->dev, "mhl est interrupt\n"); + + /* Discovery override */ + mhl_tx_writeb(ctx, MHL_TX_MHLTX_CTL1_REG, 0x10); + /* Increase DDC translation layer timer (byte mode) */ + cbus_writeb(ctx, 0x07, 0x32); + cbus_writebm(ctx, 0x44, ~0, 1 << 1); + /* Keep the discovery enabled. Need RGND interrupt */ + mhl_tx_writebm(ctx, MHL_TX_DISC_CTRL1_REG, ~0, 1); + mhl_tx_writeb(ctx, MHL_TX_INTR1_ENABLE_REG, + RSEN_CHANGE_INT_MASK | HPD_CHANGE_INT_MASK); + + if (sii9234_clear_error(ctx)) + return ST_FAILURE; + + return ST_MHL_ESTABLISHED; +} + +static enum sii9234_state sii9234_hpd_change(struct sii9234 *ctx) +{ + int value; + + value = cbus_readb(ctx, CBUS_MSC_REQ_ABORT_REASON_REG); + if (sii9234_clear_error(ctx)) + return ST_FAILURE; + + if (value & SET_HPD_DOWNSTREAM) { + /* Downstream HPD High, Enable TMDS */ + sii9234_tmds_control(ctx, true); + } else { + /* Downstream HPD Low, Disable TMDS */ + sii9234_tmds_control(ctx, false); + } + + return ctx->state; +} + +static enum sii9234_state sii9234_rsen_change(struct sii9234 *ctx) +{ + int value; + + /* Work_around code to handle wrong interrupt */ + if (ctx->state != ST_RGND_1K) { + dev_err(ctx->dev, "RSEN_HIGH without RGND_1K\n"); + return ST_FAILURE; + } + value = mhl_tx_readb(ctx, MHL_TX_SYSSTAT_REG); + if (value < 0) + return ST_FAILURE; + + if (value & RSEN_STATUS) { + dev_dbg(ctx->dev, "MHL cable connected.. RSEN High\n"); + return ST_RSEN_HIGH; + } + dev_dbg(ctx->dev, "RSEN lost\n"); + /* + * Once RSEN loss is confirmed,we need to check + * based on cable status and chip power status,whether + * it is SINK Loss(HDMI cable not connected, TV Off) + * or MHL cable disconnection + * TODO: Define the below mhl_disconnection() + */ + msleep(T_SRC_RXSENSE_DEGLITCH); + value = mhl_tx_readb(ctx, MHL_TX_SYSSTAT_REG); + if (value < 0) + return ST_FAILURE; + dev_dbg(ctx->dev, "sys_stat: %x\n", value); + + if (value & RSEN_STATUS) { + dev_dbg(ctx->dev, "RSEN recovery\n"); + return ST_RSEN_HIGH; + } + dev_dbg(ctx->dev, "RSEN Really LOW\n"); + /* To meet CTS 3.3.22.2 spec */ + sii9234_tmds_control(ctx, false); + force_usb_id_switch_open(ctx); + release_usb_id_switch_open(ctx); + + return ST_FAILURE; +} + +static irqreturn_t sii9234_irq_thread(int irq, void *data) +{ + struct sii9234 *ctx = data; + int intr1, intr4; + int intr1_en, intr4_en; + int cbus_intr1, cbus_intr2; + + dev_dbg(ctx->dev, "%s\n", __func__); + + mutex_lock(&ctx->lock); + + intr1 = mhl_tx_readb(ctx, MHL_TX_INTR1_REG); + intr4 = mhl_tx_readb(ctx, MHL_TX_INTR4_REG); + intr1_en = mhl_tx_readb(ctx, MHL_TX_INTR1_ENABLE_REG); + intr4_en = mhl_tx_readb(ctx, MHL_TX_INTR4_ENABLE_REG); + cbus_intr1 = cbus_readb(ctx, CBUS_INT_STATUS_1_REG); + cbus_intr2 = cbus_readb(ctx, CBUS_INT_STATUS_2_REG); + + if (sii9234_clear_error(ctx)) + goto done; + + dev_dbg(ctx->dev, "irq %02x/%02x %02x/%02x %02x/%02x\n", + intr1, intr1_en, intr4, intr4_en, cbus_intr1, cbus_intr2); + + if (intr4 & RGND_READY_INT) + ctx->state = sii9234_rgnd_ready_irq(ctx); + if (intr1 & RSEN_CHANGE_INT) + ctx->state = sii9234_rsen_change(ctx); + if (intr4 & MHL_EST_INT) + ctx->state = sii9234_mhl_established(ctx); + if (intr1 & HPD_CHANGE_INT) + ctx->state = sii9234_hpd_change(ctx); + if (intr4 & CBUS_LKOUT_INT) + ctx->state = ST_FAILURE; + if (intr4 & MHL_DISC_FAIL_INT) + ctx->state = ST_FAILURE_DISCOVERY; + + done: + /* Clean interrupt status and pending flags */ + mhl_tx_writeb(ctx, MHL_TX_INTR1_REG, intr1); + mhl_tx_writeb(ctx, MHL_TX_INTR4_REG, intr4); + cbus_writeb(ctx, CBUS_MHL_STATUS_REG_0, 0xFF); + cbus_writeb(ctx, CBUS_MHL_STATUS_REG_1, 0xFF); + cbus_writeb(ctx, CBUS_INT_STATUS_1_REG, cbus_intr1); + cbus_writeb(ctx, CBUS_INT_STATUS_2_REG, cbus_intr2); + + sii9234_clear_error(ctx); + + if (ctx->state == ST_FAILURE) { + dev_dbg(ctx->dev, "try to reset after failure\n"); + sii9234_hw_reset(ctx); + sii9234_goto_d3(ctx); + } + + if (ctx->state == ST_FAILURE_DISCOVERY) { + dev_err(ctx->dev, "discovery failed, no power for MHL?\n"); + tpi_writebm(ctx, TPI_DPD_REG, 0, 1); + ctx->state = ST_D3; + } + + mutex_unlock(&ctx->lock); + + return IRQ_HANDLED; +} + +static int sii9234_init_resources(struct sii9234 *ctx, + struct i2c_client *client) +{ + struct i2c_adapter *adapter = client->adapter; + int ret; + + if (!ctx->dev->of_node) { + dev_err(ctx->dev, "not DT device\n"); + return -ENODEV; + } + + ctx->gpio_reset = devm_gpiod_get(ctx->dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->gpio_reset)) { + dev_err(ctx->dev, "failed to get reset gpio from DT\n"); + return PTR_ERR(ctx->gpio_reset); + } + + ctx->supplies[0].supply = "avcc12"; + ctx->supplies[1].supply = "avcc33"; + ctx->supplies[2].supply = "iovcc18"; + ctx->supplies[3].supply = "cvcc12"; + ret = devm_regulator_bulk_get(ctx->dev, 4, ctx->supplies); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(ctx->dev, "regulator_bulk failed\n"); + return ret; + } + + ctx->client[I2C_MHL] = client; + + ctx->client[I2C_TPI] = devm_i2c_new_dummy_device(&client->dev, adapter, + I2C_TPI_ADDR); + if (IS_ERR(ctx->client[I2C_TPI])) { + dev_err(ctx->dev, "failed to create TPI client\n"); + return PTR_ERR(ctx->client[I2C_TPI]); + } + + ctx->client[I2C_HDMI] = devm_i2c_new_dummy_device(&client->dev, adapter, + I2C_HDMI_ADDR); + if (IS_ERR(ctx->client[I2C_HDMI])) { + dev_err(ctx->dev, "failed to create HDMI RX client\n"); + return PTR_ERR(ctx->client[I2C_HDMI]); + } + + ctx->client[I2C_CBUS] = devm_i2c_new_dummy_device(&client->dev, adapter, + I2C_CBUS_ADDR); + if (IS_ERR(ctx->client[I2C_CBUS])) { + dev_err(ctx->dev, "failed to create CBUS client\n"); + return PTR_ERR(ctx->client[I2C_CBUS]); + } + + return 0; +} + +static inline struct sii9234 *bridge_to_sii9234(struct drm_bridge *bridge) +{ + return container_of(bridge, struct sii9234, bridge); +} + +static enum drm_mode_status sii9234_mode_valid(struct drm_bridge *bridge, + const struct drm_display_info *info, + const struct drm_display_mode *mode) +{ + if (mode->clock > MHL1_MAX_CLK) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +static const struct drm_bridge_funcs sii9234_bridge_funcs = { + .mode_valid = sii9234_mode_valid, +}; + +static int sii9234_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct sii9234 *ctx; + struct device *dev = &client->dev; + int ret; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + if (!ctx) + return -ENOMEM; + + ctx->dev = dev; + mutex_init(&ctx->lock); + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { + dev_err(dev, "I2C adapter lacks SMBUS feature\n"); + return -EIO; + } + + if (!client->irq) { + dev_err(dev, "no irq provided\n"); + return -EINVAL; + } + + irq_set_status_flags(client->irq, IRQ_NOAUTOEN); + ret = devm_request_threaded_irq(dev, client->irq, NULL, + sii9234_irq_thread, + IRQF_TRIGGER_HIGH | IRQF_ONESHOT, + "sii9234", ctx); + if (ret < 0) { + dev_err(dev, "failed to install IRQ handler\n"); + return ret; + } + + ret = sii9234_init_resources(ctx, client); + if (ret < 0) + return ret; + + i2c_set_clientdata(client, ctx); + + ctx->bridge.funcs = &sii9234_bridge_funcs; + ctx->bridge.of_node = dev->of_node; + drm_bridge_add(&ctx->bridge); + + sii9234_cable_in(ctx); + + return 0; +} + +static void sii9234_remove(struct i2c_client *client) +{ + struct sii9234 *ctx = i2c_get_clientdata(client); + + sii9234_cable_out(ctx); + drm_bridge_remove(&ctx->bridge); +} + +static const struct of_device_id sii9234_dt_match[] = { + { .compatible = "sil,sii9234" }, + { }, +}; +MODULE_DEVICE_TABLE(of, sii9234_dt_match); + +static const struct i2c_device_id sii9234_id[] = { + { "SII9234", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(i2c, sii9234_id); + +static struct i2c_driver sii9234_driver = { + .driver = { + .name = "sii9234", + .of_match_table = sii9234_dt_match, + }, + .probe = sii9234_probe, + .remove = sii9234_remove, + .id_table = sii9234_id, +}; + +module_i2c_driver(sii9234_driver); +MODULE_LICENSE("GPL"); -- cgit v1.2.3