// SPDX-License-Identifier: GPL-2.0 #include "qcom-msm8974.dtsi" #include "qcom-pm8841.dtsi" #include "qcom-pm8941.dtsi" #include <dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { aliases { serial0 = &blsp1_uart2; }; chosen { stdout-path = "serial0:115200n8"; }; gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default"; pinctrl-0 = <&gpio_keys_pin_a>; key-volume-down { label = "volume_down"; gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; linux,input-type = <1>; linux,code = <KEY_VOLUMEDOWN>; }; key-camera-snapshot { label = "camera_snapshot"; gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; linux,input-type = <1>; linux,code = <KEY_CAMERA>; }; key-camera-focus { label = "camera_focus"; gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>; linux,input-type = <1>; linux,code = <KEY_CAMERA_FOCUS>; }; key-volume-up { label = "volume_up"; gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; linux,input-type = <1>; linux,code = <KEY_VOLUMEUP>; }; }; reserved-memory { #address-cells = <1>; #size-cells = <1>; ranges; ramoops@3e8e0000 { compatible = "ramoops"; reg = <0x3e8e0000 0x200000>; console-size = <0x100000>; record-size = <0x10000>; ftrace-size = <0x10000>; pmsg-size = <0x80000>; }; }; }; &blsp1_i2c2 { status = "okay"; clock-frequency = <355000>; synaptics@2c { compatible = "syna,rmi4-i2c"; reg = <0x2c>; interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>; #address-cells = <1>; #size-cells = <0>; vdd-supply = <&pm8941_l22>; vio-supply = <&pm8941_lvs3>; pinctrl-names = "default"; pinctrl-0 = <&ts_int_pin>; syna,startup-delay-ms = <10>; rmi4-f01@1 { reg = <0x1>; syna,nosleep-mode = <1>; }; rmi4-f11@11 { reg = <0x11>; touchscreen-inverted-x; syna,sensor-type = <1>; }; }; }; &blsp1_i2c6 { status = "okay"; clock-frequency = <355000>; nfc@28 { compatible = "nxp,pn544-i2c"; reg = <0x28>; interrupt-parent = <&tlmm>; interrupts = <59 IRQ_TYPE_EDGE_RISING>; enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>; firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>; }; }; &blsp1_uart2 { status = "okay"; }; &blsp2_dma { qcom,controlled-remotely; }; &blsp2_i2c5 { status = "okay"; clock-frequency = <355000>; /* sii8334 MHL HDMI bridge */ }; &otg { status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; extcon = <&smbb>, <&usb_id>; vbus-supply = <&chg_otg>; hnp-disable; srp-disable; adp-disable; ulpi { phy@a { status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; extcon = <&smbb>; qcom,init-seq = /bits/ 8 <0x1 0x64>; }; }; }; &pm8941_coincell { status = "okay"; qcom,rset-ohms = <2100>; qcom,vset-millivolts = <3000>; }; &pm8941_gpios { gpio_keys_pin_a: gpio-keys-active-state { pins = "gpio2", "gpio3", "gpio4", "gpio5"; function = "normal"; bias-pull-up; power-source = <PM8941_GPIO_S3>; }; }; &pm8941_lpg { status = "okay"; qcom,power-source = <1>; rgb-led { color = <LED_COLOR_ID_RGB>; function = LED_FUNCTION_STATUS; #address-cells = <1>; #size-cells = <0>; led@5 { reg = <5>; color = <LED_COLOR_ID_BLUE>; }; led@6 { reg = <6>; color = <LED_COLOR_ID_GREEN>; }; led@7 { reg = <7>; color = <LED_COLOR_ID_RED>; }; }; }; &pm8941_wled { status = "okay"; qcom,cs-out; qcom,current-limit = <20>; qcom,current-boost-limit = <805>; qcom,switching-freq = <1600>; qcom,ovp = <29>; qcom,num-strings = <2>; }; &rpm_requests { pm8841-regulators { compatible = "qcom,rpm-pm8841-regulators"; pm8841_s1: s1 { regulator-min-microvolt = <675000>; regulator-max-microvolt = <1050000>; }; pm8841_s2: s2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <1050000>; }; pm8841_s3: s3 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <1050000>; }; pm8841_s4: s4 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <1050000>; }; }; pm8941-regulators { compatible = "qcom,rpm-pm8941-regulators"; vdd_l1_l3-supply = <&pm8941_s1>; vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; vdd_l4_l11-supply = <&pm8941_s1>; vdd_l5_l7-supply = <&pm8941_s2>; vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; vdd_l9_l10_l17_l22-supply = <&vreg_boost>; vdd_l13_l20_l23_l24-supply = <&vreg_boost>; vdd_l21-supply = <&vreg_boost>; pm8941_s1: s1 { regulator-min-microvolt = <1300000>; regulator-max-microvolt = <1300000>; regulator-always-on; regulator-boot-on; }; pm8941_s2: s2 { regulator-min-microvolt = <2150000>; regulator-max-microvolt = <2150000>; regulator-boot-on; }; pm8941_s3: s3 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; pm8941_s4: s4 { regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; }; pm8941_l1: l1 { regulator-min-microvolt = <1225000>; regulator-max-microvolt = <1225000>; regulator-always-on; regulator-boot-on; }; pm8941_l2: l2 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; pm8941_l3: l3 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; pm8941_l4: l4 { regulator-min-microvolt = <1225000>; regulator-max-microvolt = <1225000>; }; pm8941_l5: l5 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; pm8941_l6: l6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; }; pm8941_l7: l7 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; }; pm8941_l8: l8 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; pm8941_l9: l9 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2950000>; }; pm8941_l11: l11 { regulator-min-microvolt = <1300000>; regulator-max-microvolt = <1350000>; }; pm8941_l12: l12 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; pm8941_l13: l13 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2950000>; regulator-boot-on; }; pm8941_l14: l14 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; pm8941_l15: l15 { regulator-min-microvolt = <2050000>; regulator-max-microvolt = <2050000>; }; pm8941_l16: l16 { regulator-min-microvolt = <2700000>; regulator-max-microvolt = <2700000>; }; pm8941_l17: l17 { regulator-min-microvolt = <2700000>; regulator-max-microvolt = <2700000>; }; pm8941_l18: l18 { regulator-min-microvolt = <2850000>; regulator-max-microvolt = <2850000>; }; pm8941_l19: l19 { regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; pm8941_l20: l20 { regulator-min-microvolt = <2950000>; regulator-max-microvolt = <2950000>; regulator-system-load = <200000>; regulator-allow-set-load; regulator-boot-on; }; pm8941_l21: l21 { regulator-min-microvolt = <2950000>; regulator-max-microvolt = <2950000>; regulator-boot-on; }; pm8941_l22: l22 { regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; }; pm8941_l23: l23 { regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; pm8941_l24: l24 { regulator-min-microvolt = <3075000>; regulator-max-microvolt = <3075000>; regulator-boot-on; }; pm8941_lvs3: lvs3 {}; }; }; &sdhc_1 { status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdc1_on>; pinctrl-1 = <&sdc1_off>; }; &sdhc_2 { status = "okay"; vmmc-supply = <&pm8941_l21>; vqmmc-supply = <&pm8941_l13>; cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdc2_on>; pinctrl-1 = <&sdc2_off>; }; &smbb { qcom,fast-charge-safe-current = <1500000>; qcom,fast-charge-current-limit = <1500000>; qcom,dc-current-limit = <1800000>; qcom,fast-charge-safe-voltage = <4400000>; qcom,fast-charge-high-threshold-voltage = <4350000>; qcom,fast-charge-low-threshold-voltage = <3400000>; qcom,auto-recharge-threshold-voltage = <4200000>; qcom,minimum-input-voltage = <4300000>; }; &tlmm { ts_int_pin: touch-int { pins = "gpio61"; function = "gpio"; drive-strength = <2>; bias-disable; input-enable; }; sdc1_on: sdc1-on { clk { pins = "sdc1_clk"; drive-strength = <16>; bias-disable; }; cmd-data { pins = "sdc1_cmd", "sdc1_data"; drive-strength = <10>; bias-pull-up; }; }; sdc2_on: sdc-on { clk { pins = "sdc2_clk"; drive-strength = <10>; bias-disable; }; cmd-data { pins = "sdc2_cmd", "sdc2_data"; drive-strength = <6>; bias-pull-up; }; cd { pins = "gpio62"; function = "gpio"; drive-strength = <2>; bias-disable; }; }; };