Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 118 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
new file mode 100644
index 000000000..12c316ff4
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -0,0 +1,118 @@
+* Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
+
+Required properties:
+- compatible : Should be one of
+      "fsl,imx25-sdma"
+      "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
+      "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
+      "fsl,imx51-sdma"
+      "fsl,imx53-sdma"
+      "fsl,imx6q-sdma"
+      "fsl,imx7d-sdma"
+      "fsl,imx6ul-sdma"
+      "fsl,imx8mq-sdma"
+      "fsl,imx8mm-sdma"
+      "fsl,imx8mn-sdma"
+      "fsl,imx8mp-sdma"
+  The -to variants should be preferred since they allow to determine the
+  correct ROM script addresses needed for the driver to work without additional
+  firmware.
+- reg : Should contain SDMA registers location and length
+- interrupts : Should contain SDMA interrupt
+- #dma-cells : Must be <3>.
+  The first cell specifies the DMA request/event ID.  See details below
+  about the second and third cell.
+- fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM
+  scripts firmware
+
+The second cell of dma phandle specifies the peripheral type of DMA transfer.
+The full ID of peripheral types can be found below.
+
+	ID	transfer type
+	---------------------
+	0	MCU domain SSI
+	1	Shared SSI
+	2	MMC
+	3	SDHC
+	4	MCU domain UART
+	5	Shared UART
+	6	FIRI
+	7	MCU domain CSPI
+	8	Shared CSPI
+	9	SIM
+	10	ATA
+	11	CCM
+	12	External peripheral
+	13	Memory Stick Host Controller
+	14	Shared Memory Stick Host Controller
+	15	DSP
+	16	Memory
+	17	FIFO type Memory
+	18	SPDIF
+	19	IPU Memory
+	20	ASRC
+	21	ESAI
+	22	SSI Dual FIFO	(needs firmware ver >= 2)
+	23	Shared ASRC
+	24	SAI
+
+The third cell specifies the transfer priority as below.
+
+	ID	transfer priority
+	-------------------------
+	0	High
+	1	Medium
+	2	Low
+
+Optional properties:
+
+- gpr : The phandle to the General Purpose Register (GPR) node.
+- fsl,sdma-event-remap : Register bits of sdma event remap, the format is
+  <reg shift val>.
+    reg is the GPR register offset.
+    shift is the bit position inside the GPR register.
+    val is the value of the bit (0 or 1).
+
+Examples:
+
+sdma@83fb0000 {
+	compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
+	reg = <0x83fb0000 0x4000>;
+	interrupts = <6>;
+	#dma-cells = <3>;
+	fsl,sdma-ram-script-name = "sdma-imx51.bin";
+};
+
+DMA clients connected to the i.MX SDMA controller must use the format
+described in the dma.txt file.
+
+Examples:
+
+ssi2: ssi@70014000 {
+	compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+	reg = <0x70014000 0x4000>;
+	interrupts = <30>;
+	clocks = <&clks 49>;
+	dmas = <&sdma 24 1 0>,
+	       <&sdma 25 1 0>;
+	dma-names = "rx", "tx";
+	fsl,fifo-depth = <15>;
+};
+
+Using the fsl,sdma-event-remap property:
+
+If we want to use SDMA on the SAI1 port on a MX6SX:
+
+&sdma {
+	gpr = <&gpr>;
+	/* SDMA events remap for SAI1_RX and SAI1_TX */
+	fsl,sdma-event-remap = <0 15 1>, <0 16 1>;
+};
+
+The fsl,sdma-event-remap property in this case has two values:
+- <0 15 1> means that the offset is 0, so GPR0 is the register of the
+SDMA remap. Bit 15 of GPR0 selects between UART4_RX and SAI1_RX.
+Setting bit 15 to 1 selects SAI1_RX.
+- <0 16 1> means that the offset is 0, so GPR0 is the register of the
+SDMA remap. Bit 16 of GPR0 selects between UART4_TX and SAI1_TX.
+Setting bit 16 to 1 selects SAI1_TX.