Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

62 files changed, 5516 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
new file mode 100644
index 000000000..5764cbedf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
@@ -0,0 +1,28 @@
+* Analog Devices AD5820 autofocus coil
+
+Required Properties:
+
+  - compatible: Must contain one of:
+		- "adi,ad5820"
+		- "adi,ad5821"
+		- "adi,ad5823"
+
+  - reg: I2C slave address
+
+  - VANA-supply: supply of voltage for VANA pin
+
+Optional properties:
+
+   - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is
+active low, a high level on the pin enables the device.
+
+Example:
+
+       ad5820: coil@c {
+               compatible = "adi,ad5820";
+               reg = <0x0c>;
+
+               VANA-supply = <&vaux4>;
+               enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
+       };
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
new file mode 100644
index 000000000..4cce0de40
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
@@ -0,0 +1,38 @@
+* Analog Devices ADP1653 flash LED driver
+
+Required Properties:
+
+  - compatible: Must contain "adi,adp1653"
+
+  - reg: I2C slave address
+
+  - enable-gpios: Specifier of the GPIO connected to EN pin
+
+There are two LED outputs available - flash and indicator. One LED is
+represented by one child node, nodes need to be named "flash" and "indicator".
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Required properties of the flash LED child node:
+
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+	adp1653: led-controller@30 {
+		compatible = "adi,adp1653";
+		reg = <0x30>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+		flash {
+			flash-timeout-us = <500000>;
+			flash-max-microamp = <320000>;
+			led-max-microamp = <50000>;
+		};
+		indicator {
+			led-max-microamp = <17500>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.yaml b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml
new file mode 100644
index 000000000..c8d887eee
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7180.yaml
@@ -0,0 +1,179 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/adv7180.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7180 analog video decoder family
+
+maintainers:
+  - Lars-Peter Clausen <lars@metafoo.de>
+
+description:
+  The adv7180 family devices are used to capture analog video to different
+  digital interfaces like MIPI CSI-2 or parallel video.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - adi,adv7180
+          - adi,adv7180cp
+          - adi,adv7180st
+          - adi,adv7182
+          - adi,adv7280
+          - adi,adv7280-m
+          - adi,adv7281
+          - adi,adv7281-m
+          - adi,adv7281-ma
+          - adi,adv7282
+          - adi,adv7282-m
+
+  reg:
+    maxItems: 1
+
+  powerdown-gpios:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  adv,force-bt656-4:
+    description:
+      Indicates that the output is a BT.656-4 compatible stream.
+    type: boolean
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+  ports: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          enum:
+            - adi,adv7180
+            - adi,adv7182
+            - adi,adv7280
+            - adi,adv7280-m
+            - adi,adv7281
+            - adi,adv7281-m
+            - adi,adv7281-ma
+            - adi,adv7282
+            - adi,adv7282-m
+    then:
+      required:
+        - port
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7180cp
+    then:
+      properties:
+        ports:
+          $ref: /schemas/graph.yaml#/properties/ports
+          properties:
+            port@3:
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Output port
+
+          patternProperties:
+            "^port@[0-2]$":
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Input port
+
+          required:
+            - port@3
+
+      required:
+        - ports
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7180st
+    then:
+      properties:
+        ports:
+          $ref: /schemas/graph.yaml#/properties/ports
+          properties:
+            port@6:
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Output port
+
+          patternProperties:
+            "^port@[0-5]$":
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Input port
+
+          required:
+            - port@6
+
+      required:
+        - ports
+
+examples:
+  - |
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            composite-in@20 {
+                    compatible = "adi,adv7180";
+                    reg = <0x20>;
+
+                    port {
+                            adv7180: endpoint {
+                                    bus-width = <8>;
+                                    remote-endpoint = <&vin1ep>;
+                            };
+                    };
+            };
+
+    };
+
+  - |
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            composite-in@20 {
+                    compatible = "adi,adv7180cp";
+                    reg = <0x20>;
+
+                    ports {
+                            #address-cells = <1>;
+                            #size-cells = <0>;
+
+                            port@0 {
+                                    reg = <0>;
+                                    adv7180_in: endpoint {
+                                            remote-endpoint = <&composite_con_in>;
+                                    };
+                            };
+
+                            port@3 {
+                                    reg = <3>;
+                                    adv7180_out: endpoint {
+                                            remote-endpoint = <&vin4_in>;
+                                    };
+                            };
+                    };
+            };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
new file mode 100644
index 000000000..5653bc242
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
@@ -0,0 +1,48 @@
+* Analog Devices adv7343 video encoder
+
+The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP
+package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite
+(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard
+definition (SD), enhanced definition (ED), or high definition (HD) video
+formats.
+
+Required Properties :
+- compatible: Must be "adi,adv7343"
+
+Optional Properties :
+- adi,power-mode-sleep-mode: on enable the current consumption is reduced to
+			      micro ampere level. All DACs and the internal PLL
+			      circuit are disabled.
+- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
+			   internal PLL 1 circuit to be powered down and the
+			   oversampling to be switched off.
+- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
+			      0 = OFF and 1 = ON, Default value when this
+			      property is not specified is <0 0 0 0 0 0>.
+- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF
+				 and 1 = ON, Default value when this property is
+				 not specified is <0 0>.
+
+Example:
+
+i2c0@1c22000 {
+	...
+	...
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			adv7343_1: endpoint {
+					adi,power-mode-sleep-mode;
+					adi,power-mode-pll-ctrl;
+					/* Use DAC1..3, DAC6 */
+					adi,dac-enable = <1 1 1 0 0 1>;
+					/* Use SD DAC output 1 */
+					adi,sd-dac-enable = <1 0>;
+			};
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.yaml b/Documentation/devicetree/bindings/media/i2c/adv748x.yaml
new file mode 100644
index 000000000..d63530814
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv748x.yaml
@@ -0,0 +1,212 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/adv748x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV748X video decoder with HDMI receiver
+
+maintainers:
+  - Kieran Bingham <kieran.bingham@ideasonboard.com>
+  - Niklas Söderlund <niklas.soderlund@ragnatech.se>
+
+description:
+  The ADV7481 and ADV7482 are multi format video decoders with an integrated
+  HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB
+  from three input sources HDMI, analog and TTL.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - adi,adv7481
+          - adi,adv7482
+
+  reg:
+    minItems: 1
+    maxItems: 12
+    description:
+      The ADV748x has up to twelve 256-byte maps that can be accessed via the
+      main I2C ports. Each map has it own I2C address and acts as a standard
+      slave device on the I2C bus. The main address is mandatory, others are
+      optional and remain at default values if not specified.
+
+  reg-names:
+    minItems: 1
+    items:
+      - const: main
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+      - enum: [ dpll, cp, hdmi, edid, repeater, infoframe, cbus, cec, sdp, txa, txb ]
+
+  interrupts: true
+
+  interrupt-names: true
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    patternProperties:
+      "^port@[0-7]$":
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input port nodes for analog inputs AIN[0-7].
+
+    properties:
+      port@8:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input port node for HDMI.
+
+      port@9:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input port node for TTL.
+
+      port@a:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Output port node, single endpoint describing the CSI-2 transmitter TXA.
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@b:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Output port node, single endpoint describing the CSI-2 transmitter TXB.
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                maxItems: 1
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7481
+    then:
+      properties:
+        interrupts:
+          minItems: 1
+          maxItems: 3
+
+        interrupt-names:
+          minItems: 1
+          maxItems: 3
+          items:
+            enum: [ intrq1, intrq2, intrq3 ]
+    else:
+      properties:
+        interrupts:
+          minItems: 1
+          maxItems: 2
+
+        interrupt-names:
+          minItems: 1
+          maxItems: 2
+          items:
+            enum: [ intrq1, intrq2 ]
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - ports
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        video-receiver@70 {
+            compatible = "adi,adv7482";
+            reg = <0x70 0x71 0x72 0x73 0x74 0x75
+                   0x60 0x61 0x62 0x63 0x64 0x65>;
+            reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
+                        "infoframe", "cbus", "cec", "sdp", "txa", "txb";
+
+            interrupt-parent = <&gpio6>;
+            interrupts = <30 IRQ_TYPE_LEVEL_LOW>, <31 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-names = "intrq1", "intrq2";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@7 {
+                    reg = <7>;
+
+                    adv7482_ain7: endpoint {
+                        remote-endpoint = <&cvbs_in>;
+                    };
+                };
+
+                port@8 {
+                    reg = <8>;
+
+                    adv7482_hdmi: endpoint {
+                        remote-endpoint = <&hdmi_in>;
+                    };
+                };
+
+                port@a {
+                    reg = <10>;
+
+                    adv7482_txa: endpoint {
+                        clock-lanes = <0>;
+                        data-lanes = <1 2 3 4>;
+                        remote-endpoint = <&csi40_in>;
+                    };
+                };
+
+                port@b {
+                    reg = <11>;
+
+                    adv7482_txb: endpoint {
+                        clock-lanes = <0>;
+                        data-lanes = <1>;
+                        remote-endpoint = <&csi20_in>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.yaml b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml
new file mode 100644
index 000000000..7589d377c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/adv7604.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7604/10/11/12 video decoder with HDMI receiver
+
+maintainers:
+  - Hans Verkuil <hverkuil-cisco@xs4all.nl>
+
+description:
+  The ADV7604 and ADV7610/11/12 are multiformat video decoders with
+  an integrated HDMI receiver. The ADV7604 has four multiplexed HDMI inputs
+  and one analog input, and the ADV7610/11 have one HDMI input and no analog
+  input. The ADV7612 is similar to the ADV7610/11 but has 2 HDMI inputs.
+
+  These device tree bindings support the ADV7610/11/12 only at the moment.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - adi,adv7610
+          - adi,adv7611
+          - adi,adv7612
+
+  reg:
+    minItems: 1
+    maxItems: 13
+
+  reg-names:
+    minItems: 1
+    items:
+      - const: main
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  hpd-gpios:
+    minItems: 1
+    description:
+      References to the GPIOs that control the HDMI hot-plug detection pins,
+      one per HDMI input. The active flag indicates the GPIO level that
+      enables hot-plug detection.
+
+  default-input:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 1 ]
+    description:
+      Select which input is selected after reset.
+
+  ports: true
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7611
+    then:
+      properties:
+        ports:
+          $ref: /schemas/graph.yaml#/properties/ports
+          properties:
+            port@0:
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Input port
+
+            port@1:
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Output port
+
+          required:
+            - port@1
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7612
+    then:
+      properties:
+        ports:
+          $ref: /schemas/graph.yaml#/properties/ports
+          properties:
+            port@2:
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Output port
+
+          patternProperties:
+            "^port@[0-1]$":
+              $ref: /schemas/graph.yaml#/properties/port
+              description: Input port
+
+          required:
+            - port@2
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            hdmi_receiver@4c {
+                    compatible = "adi,adv7611";
+                    /*
+                     * The edid page will be accessible @ 0x66 on the I2C bus. All
+                     * other maps will retain their default addresses.
+                     */
+                    reg = <0x4c>, <0x66>;
+                    reg-names = "main", "edid";
+
+                    reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+                    hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+                    default-input = <0>;
+
+                    ports {
+                            #address-cells = <1>;
+                            #size-cells = <0>;
+
+                            port@0 {
+                                    reg = <0>;
+                            };
+
+                            port@1 {
+                                    reg = <1>;
+                                    hdmi_in: endpoint {
+                                            remote-endpoint = <&ccdc_in>;
+                                    };
+                            };
+                    };
+
+
+            };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
new file mode 100644
index 000000000..aa3e24b41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
@@ -0,0 +1,8 @@
+Asahi Kasei Microdevices AK7375 voice coil lens driver
+
+AK7375 is a camera voice coil lens.
+
+Mandatory properties:
+
+- compatible: "asahi-kasei,ak7375"
+- reg: I2C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml
new file mode 100644
index 000000000..1d6af1bf9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9p031.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/aptina,mt9p031.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor
+  with an active array size of 2592H x 1944V. It is programmable through a
+  simple two-wire serial interface.
+
+properties:
+  compatible:
+    enum:
+      - aptina,mt9p006
+      - aptina,mt9p031
+      - aptina,mt9p031m
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  vdd-supply:
+    description: Digital supply voltage, 1.8 V
+
+  vdd_io-supply:
+    description: I/O supply voltage, 1.8 or 2.8 V
+
+  vaa-supply:
+    description: Analog supply voltage, 2.8 V
+
+  reset-gpios:
+    maxItems: 1
+    description: Chip reset GPIO
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          input-clock-frequency:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            minimum: 6000000
+            maximum: 96000000
+            description: Input clock frequency
+
+          pixel-clock-frequency:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            maximum: 96000000
+            description: Target pixel clock frequency
+
+          pclk-sample:
+            default: 0
+
+        required:
+          - input-clock-frequency
+          - pixel-clock-frequency
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - vdd-supply
+  - vdd_io-supply
+  - vaa-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        mt9p031@5d {
+            compatible = "aptina,mt9p031";
+            reg = <0x5d>;
+            reset-gpios = <&gpio_sensor 0 0>;
+
+            clocks = <&sensor_clk>;
+
+            vdd-supply = <&reg_vdd>;
+            vdd_io-supply = <&reg_vdd_io>;
+            vaa-supply = <&reg_vaa>;
+
+            port {
+                mt9p031_1: endpoint {
+                    input-clock-frequency = <6000000>;
+                    pixel-clock-frequency = <96000000>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml
new file mode 100644
index 000000000..e53b8d65f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/aptina,mt9v111.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aptina MT9V111 CMOS sensor
+
+maintainers:
+  - Jacopo Mondi <jacopo@jmondi.org>
+
+description: |
+  The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
+  based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
+
+  The sensor has an active pixel array of 640x480 pixels and can output a number
+  of image resolutions and formats controllable through a simple two-wires
+  interface.
+
+properties:
+  compatible:
+    const: aptina,mt9v111
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  enable-gpios:
+    description: Enable signal, pin name "OE#". Active low.
+    maxItems: 1
+
+  standby-gpios:
+    description: |
+      Low power state control signal, pin name "STANDBY". Active high.
+    maxItems: 1
+
+  reset-gpios:
+    description: Chip reset signal, pin name "RESET#". Active low.
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description: |
+      Output video port.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@48 {
+            compatible = "aptina,mt9v111";
+            reg = <0x48>;
+            clocks = <&camera_clk>;
+
+            port {
+                mt9v111_out: endpoint {
+                    remote-endpoint = <&ceu_in>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml
new file mode 100644
index 000000000..63e5b89d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/chrontel,ch7322.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/media/i2c/chrontel,ch7322.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Chrontel HDMI-CEC Controller
+
+maintainers:
+  - Jeff Chase <jnchase@google.com>
+
+description:
+  The Chrontel CH7322 is a discrete HDMI-CEC controller. It is
+  programmable through I2C and drives a single CEC line.
+
+properties:
+  compatible:
+    const: chrontel,ch7322
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      Reference to the GPIO connected to the RESET pin, if any. This
+      pin is active-low.
+    maxItems: 1
+
+  standby-gpios:
+    description:
+      Reference to the GPIO connected to the OE pin, if any. When low
+      the device will respond to power status requests with "standby"
+      if in auto mode.
+    maxItems: 1
+
+  # see ../cec.txt
+  hdmi-phandle:
+    description: phandle to the HDMI controller
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      ch7322@75 {
+        compatible = "chrontel,ch7322";
+        reg = <0x75>;
+        interrupts = <47 IRQ_TYPE_EDGE_RISING>;
+        standby-gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+        reset-gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+        hdmi-phandle = <&hdmi>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml
new file mode 100644
index 000000000..66229a3dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9714.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dongwoon Anatech DW9714 camera voice coil lens driver
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description:
+  DW9174 is a 10-bit DAC with current sink capability. It is intended for
+  driving voice coil lenses in camera modules.
+
+properties:
+  compatible:
+    const: dongwoon,dw9714
+
+  reg:
+    maxItems: 1
+
+  powerdown-gpios:
+    description:
+      XSD pin for shutdown (active low)
+
+  vcc-supply:
+    description: VDD power supply
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera-lens@c {
+            compatible = "dongwoon,dw9714";
+            reg = <0x0c>;
+            vcc-supply = <&reg_csi_1v8>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
new file mode 100644
index 000000000..21864ab86
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9768.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dongwoon Anatech DW9768 Voice Coil Motor (VCM) Lens Device Tree Bindings
+
+maintainers:
+  - Dongchun Zhu <dongchun.zhu@mediatek.com>
+
+description: |-
+  The Dongwoon DW9768 is a single 10-bit digital-to-analog (DAC) converter
+  with 100 mA output current sink capability. VCM current is controlled with
+  a linear mode driver. The DAC is controlled via a 2-wire (I2C-compatible)
+  serial interface that operates at clock rates up to 1MHz. This chip
+  integrates Advanced Actuator Control (AAC) technology and is intended for
+  driving voice coil lenses in camera modules.
+
+properties:
+  compatible:
+    enum:
+      - dongwoon,dw9768 # for DW9768 VCM
+      - giantec,gt9769  # for GT9769 VCM
+
+  reg:
+    maxItems: 1
+
+  vin-supply:
+    description:
+      Definition of the regulator used as Digital I/O voltage supply.
+
+  vdd-supply:
+    description:
+      Definition of the regulator used as Digital core voltage supply.
+
+  dongwoon,aac-mode:
+    description:
+      Indication of AAC mode select.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum:
+      - 1    #  AAC2 mode(operation time# 0.48 x Tvib)
+      - 2    #  AAC3 mode(operation time# 0.70 x Tvib)
+      - 3    #  AAC4 mode(operation time# 0.75 x Tvib)
+      - 5    #  AAC8 mode(operation time# 1.13 x Tvib)
+    default: 2
+
+  dongwoon,aac-timing:
+    description:
+      Number of AAC Timing count that controlled by one 6-bit period of
+      vibration register AACT[5:0], the unit of which is 100 us.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    default: 0x20
+    minimum: 0x00
+    maximum: 0x3f
+
+  dongwoon,clock-presc:
+    description:
+      Indication of VCM internal clock dividing rate select, as one multiple
+      factor to calculate VCM ring periodic time Tvib.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum:
+      - 0    #  Dividing Rate -  2
+      - 1    #  Dividing Rate -  1
+      - 2    #  Dividing Rate -  1/2
+      - 3    #  Dividing Rate -  1/4
+      - 4    #  Dividing Rate -  8
+      - 5    #  Dividing Rate -  4
+    default: 1
+
+required:
+  - compatible
+  - reg
+  - vin-supply
+  - vdd-supply
+
+additionalProperties: false
+
+examples:
+  - |
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        dw9768: camera-lens@c {
+            compatible = "dongwoon,dw9768";
+            reg = <0x0c>;
+
+            vin-supply = <&mt6358_vcamio_reg>;
+            vdd-supply = <&mt6358_vcama2_reg>;
+            dongwoon,aac-timing = <0x39>;
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml
new file mode 100644
index 000000000..aae246ca3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2018, 2021 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/dongwoon,dw9807-vcm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dongwoon Anatech DW9807 voice coil lens driver
+
+maintainers:
+  - Sakari Ailus <sakari.ailus@linux.intel.com>
+
+description: |
+  DW9807 is a 10-bit DAC with current sink capability. It is intended for
+  controlling voice coil lenses.
+
+properties:
+  compatible:
+    const: dongwoon,dw9807-vcm
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        lens@e {
+            compatible = "dongwoon,dw9807-vcm";
+            reg = <0x0e>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
new file mode 100644
index 000000000..1e2df8cf2
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
@@ -0,0 +1,124 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
+
+maintainers:
+  - Martin Kepplinger <martin.kepplinger@puri.sm>
+
+description: |-
+  The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
+  interface and CCI (I2C compatible) control bus. The output format
+  is raw Bayer.
+
+properties:
+  compatible:
+    const: hynix,hi846
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Reference to the mclk clock.
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clock-rates:
+    maxItems: 1
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the RESETB pin. Active low.
+    maxItems: 1
+
+  shutdown-gpios:
+    description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
+    maxItems: 1
+
+  vddio-supply:
+    description: Definition of the regulator used for the VDDIO power supply.
+
+  vdda-supply:
+    description: Definition of the regulator used for the VDDA power supply.
+
+  vddd-supply:
+    description: Definition of the regulator used for the VDDD power supply.
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+              - items:
+                  - const: 1
+                  - const: 2
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - assigned-clocks
+  - assigned-clock-rates
+  - vddio-supply
+  - vdda-supply
+  - vddd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hi846: camera@20 {
+            compatible = "hynix,hi846";
+            reg = <0x20>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&pinctrl_csi1>;
+            clocks = <&clk 0>;
+            assigned-clocks = <&clk 0>;
+            assigned-clock-rates = <25000000>;
+            vdda-supply = <&reg_camera_vdda>;
+            vddd-supply = <&reg_camera_vddd>;
+            vddio-supply = <&reg_camera_vddio>;
+            reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+            shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+
+            port {
+                camera_out: endpoint {
+                    remote-endpoint = <&csi1_ep1>;
+                    link-frequencies = /bits/ 64
+                        <80000000 200000000>;
+                    data-lanes = <1 2>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml
new file mode 100644
index 000000000..e57575c44
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imi,rdacm2x-gmsl.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+# Copyright (C) 2019 Renesas Electronics Corp.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imi,rdacm2x-gmsl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IMI D&D RDACM20 and RDACM21 Automotive Camera Platforms
+
+maintainers:
+  - Jacopo Mondi <jacopo+renesas@jmondi.org>
+  - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+  - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
+
+description: -|
+  The IMI D&D RDACM20 and RDACM21 are GMSL-compatible camera designed for
+  automotive applications.
+
+  The RDACM20 camera module encloses a Maxim Integrated MAX9271 GMSL serializer,
+  coupled with an OV10635 image sensor and an embedded MCU. Both the MCU and
+  the image sensor are connected to the serializer local I2C bus and are
+  accessible by the host SoC by direct addressing.
+
+  The RDACM21 camera module encloses the same serializer, coupled with an
+  OV10640 image sensor and an OV490 ISP. Only the OV490 ISP is interfaced to
+  the serializer local I2C bus while the image sensor is not accessible from
+  the host SoC.
+
+  They both connect to a remote GMSL endpoint through a coaxial cable.
+
+                                                   IMI RDACM20
+  +---------------+                        +--------------------------------+
+  |      GMSL     |   <- Video Stream      |       <- Video--------\        |
+  |               |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV10635 |
+  | de-serializer |   <- I2C messages ->   |                   \<-->MCU     |
+  +---------------+                        +--------------------------------+
+
+                                                   IMI RDACM21
+  +---------------+                        +--------------------------------+
+  |      GMSL     |   <- Video Stream      |       <- Video--------\        |
+  |               |< === GMSL Link ====== >|MAX9271<- I2C bus-> <-->OV490   |
+  |               |   <- I2C messages ->   |                          |     |
+  | de-serializer |                        |          OV10640 <-------|     |
+  +---------------+                        +--------------------------------+
+
+  Both camera modules serialize video data generated by the embedded camera
+  sensor on the GMSL serial channel to a remote GMSL de-serializer. They also
+  receive and transmit I2C messages encapsulated and transmitted on the GMSL
+  bidirectional control channel.
+
+  All I2C traffic received on the GMSL link not directed to the serializer is
+  propagated on the local I2C bus to the remote device there connected. All the
+  I2C traffic generated on the local I2C bus not directed to the serializer is
+  propagated to the remote de-serializer encapsulated in the GMSL control
+  channel.
+
+  The RDACM20 and RDACM21 DT node should be a direct child of the GMSL
+  deserializer's I2C bus corresponding to the GMSL link that the camera is
+  attached to.
+
+properties:
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  compatible:
+    enum:
+      - imi,rdacm20
+      - imi,rdacm21
+
+  reg:
+    description: -|
+      I2C device addresses, the first to be assigned to the serializer, the
+      following ones to be assigned to the remote devices.
+
+      For RDACM20 the second entry of the property is assigned to the
+      OV10635 image sensor and the optional third one to the embedded MCU.
+
+      For RDACM21 the second entry is assigned to the OV490 ISP and the optional
+      third one ignored.
+
+    minItems: 2
+    maxItems: 3
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description:
+      Connection to the remote GMSL endpoint.
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c@e66d8000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      reg = <0 0xe66d8000>;
+
+      camera@31 {
+        compatible = "imi,rdacm20";
+        reg = <0x31>, <0x41>, <0x51>;
+
+        port {
+          rdacm20_out0: endpoint {
+            remote-endpoint = <&max9286_in0>;
+          };
+        };
+      };
+    };
+
+  - |
+    i2c@e66d8000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      reg = <0 0xe66d8000>;
+
+      camera@31 {
+        compatible = "imi,rdacm21";
+        reg = <0x31>, <0x41>;
+
+        port {
+          rdacm21_out0: endpoint {
+            remote-endpoint = <&max9286_in0>;
+          };
+        };
+      };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
new file mode 100644
index 000000000..5fc96944b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx219.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+maintainers:
+  - Dave Stevenson <dave.stevenson@raspberrypi.com>
+
+description: |-
+  The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
+  with an active array size of 3280H x 2464V. It is programmable through
+  I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+  Image data is sent through MIPI CSI-2, which is configured as either 2 or
+  4 data lanes.
+
+properties:
+  compatible:
+    const: sony,imx219
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  VDIG-supply:
+    description:
+      Digital I/O voltage supply, 1.8 volts
+
+  VANA-supply:
+    description:
+      Analog voltage supply, 2.8 volts
+
+  VDDL-supply:
+    description:
+      Digital core voltage supply, 1.2 volts
+
+  reset-gpios:
+    maxItems: 1
+    description: |-
+      Reference to the GPIO connected to the xclr pin, if any.
+      Must be released (set high) after all supplies are applied.
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            description: |-
+              The sensor supports either two-lane, or four-lane operation.
+              If this property is omitted four-lane operation is assumed.
+              For two-lane operation the property must be set to <1 2>.
+            items:
+              - const: 1
+              - const: 2
+
+          clock-noncontinuous: true
+          link-frequencies: true
+
+        required:
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - VANA-supply
+  - VDIG-supply
+  - VDDL-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx219: sensor@10 {
+            compatible = "sony,imx219";
+            reg = <0x10>;
+            clocks = <&imx219_clk>;
+            VANA-supply = <&imx219_vana>;   /* 2.8v */
+            VDIG-supply = <&imx219_vdig>;   /* 1.8v */
+            VDDL-supply = <&imx219_vddl>;   /* 1.2v */
+
+            port {
+                imx219_0: endpoint {
+                    remote-endpoint = <&csi1_ep>;
+                    data-lanes = <1 2>;
+                    clock-noncontinuous;
+                    link-frequencies = /bits/ 64 <456000000>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml
new file mode 100644
index 000000000..cde0f7383
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx258.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |-
+  IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel
+  type stacked image sensor with a square pixel array of size 4208 x 3120. It
+  is programmable through I2C interface.  Image data is sent through MIPI
+  CSI-2.
+
+properties:
+  compatible:
+    const: sony,imx258
+
+  assigned-clocks: true
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+
+  clocks:
+    description:
+      Clock frequency from 6 to 27 MHz.
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    description: |-
+      Reference to the GPIO connected to the XCLR pin, if any.
+
+  vana-supply:
+    description:
+      Analog voltage (VANA) supply, 2.7 V
+
+  vdig-supply:
+    description:
+      Digital I/O voltage (VDIG) supply, 1.2 V
+
+  vif-supply:
+    description:
+      Interface voltage (VIF) supply, 1.8 V
+
+  # See ../video-interfaces.txt for more details
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+              - items:
+                  - const: 1
+                  - const: 2
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor@6c {
+            compatible = "sony,imx258";
+            reg = <0x6c>;
+            clocks = <&imx258_clk>;
+
+            port {
+                endpoint {
+                    remote-endpoint = <&csi1_ep>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <320000000>;
+                };
+            };
+        };
+    };
+
+    /* Oscillator on the camera board */
+    imx258_clk: clk {
+        compatible = "fixed-clock";
+        #clock-cells = <0>;
+        clock-frequency = <19200000>;
+    };
+
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        sensor@6c {
+            compatible = "sony,imx258";
+            reg = <0x6c>;
+            clocks = <&imx258_clk>;
+
+            assigned-clocks = <&imx258_clk>;
+            assigned-clock-rates = <19200000>;
+
+            port {
+                endpoint {
+                    remote-endpoint = <&csi1_ep>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <633600000>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/imx290.txt b/Documentation/devicetree/bindings/media/i2c/imx290.txt
new file mode 100644
index 000000000..a3cc21410
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx290.txt
@@ -0,0 +1,57 @@
+* Sony IMX290 1/2.8-Inch CMOS Image Sensor
+
+The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
+Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
+interfaces. The sensor output is available via CMOS logic parallel SDR output,
+Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
+default. No bindings have been defined for the other busses.
+
+Required Properties:
+- compatible: Should be "sony,imx290"
+- reg: I2C bus address of the device
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock in Hz.
+- vdddo-supply: Sensor digital IO regulator.
+- vdda-supply: Sensor analog regulator.
+- vddd-supply: Sensor digital core regulator.
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx290 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Properties on endpoint:
+- data-lanes: check ../video-interfaces.txt
+- link-frequencies: check ../video-interfaces.txt
+- remote-endpoint: check ../video-interfaces.txt
+
+Example:
+	&i2c1 {
+		...
+		imx290: camera-sensor@1a {
+			compatible = "sony,imx290";
+			reg = <0x1a>;
+
+			reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+			clock-names = "xclk";
+			clock-frequency = <37125000>;
+
+			vdddo-supply = <&camera_vdddo_1v8>;
+			vdda-supply = <&camera_vdda_2v8>;
+			vddd-supply = <&camera_vddd_1v5>;
+
+			port {
+				imx290_ep: endpoint {
+					data-lanes = <1 2 3 4>;
+					link-frequencies = /bits/ 64 <445500000>;
+					remote-endpoint = <&csiphy0_ep>;
+				};
+			};
+		};
diff --git a/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml
new file mode 100644
index 000000000..034a6e346
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/isil,isl79987.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/isil,isl79987.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intersil ISL79987 Analog to MIPI CSI-2 decoder
+
+maintainers:
+  - Michael Tretter <m.tretter@pengutronix.de>
+  - Marek Vasut <marex@denx.de>
+
+description:
+  The Intersil ISL79987 is an analog to MIPI CSI-2 decoder which is capable of
+  receiving up to four analog stream and multiplexing them into up to four MIPI
+  CSI-2 virtual channels, using one MIPI clock lane and 1/2 data lanes.
+
+properties:
+  compatible:
+    enum:
+      - isil,isl79987
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      A GPIO spec for the RSTB pin (active high)
+
+  powerdown-gpios:
+    maxItems: 1
+    description:
+      A GPIO spec for the Power Down pin (active high)
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Output port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                maxItems: 2
+
+            required:
+              - data-lanes
+
+    patternProperties:
+      "^port@[1-4]$":
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input ports
+
+    required:
+      - port@0
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - ports
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      isl7998x_mipi@44 {
+        compatible = "isil,isl79987";
+        reg = <0x44>;
+        powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+        reset-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            isl79987_out: endpoint {
+              remote-endpoint = <&mipi_csi2_in>;
+              data-lanes = <1 2>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            endpoint {
+              remote-endpoint = <&camera_0>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+            endpoint {
+              remote-endpoint = <&camera_1>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt
new file mode 100644
index 000000000..02b4e9cd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt
@@ -0,0 +1,59 @@
+Maxim Integrated MAX2175 RF to Bits tuner
+-----------------------------------------
+
+The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with
+RF to Bits® front-end designed for software-defined radio solutions.
+
+Required properties:
+--------------------
+- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner.
+- clocks: clock specifier.
+- port: child port node corresponding to the I2S output, in accordance with
+	the video interface bindings defined in
+	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+	node must contain at least one endpoint.
+
+Optional properties:
+--------------------
+- maxim,master	      : phandle to the master tuner if it is a slave. This
+			is used to define two tuners in diversity mode
+			(1 master, 1 slave). By default each tuner is an
+			individual master.
+- maxim,refout-load   : load capacitance value (in picofarads) on reference
+			output drive level. The possible load values are:
+			 0 (default - refout disabled)
+			10
+			20
+			30
+			40
+			60
+			70
+- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used
+			in this hardware for AM antenna input.
+
+Example:
+--------
+
+Board specific DTS file
+
+/* Fixed XTAL clock node */
+maxim_xtal: clock {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <36864000>;
+};
+
+/* A tuner device instance under i2c bus */
+max2175_0: tuner@60 {
+	compatible = "maxim,max2175";
+	reg = <0x60>;
+	clocks = <&maxim_xtal>;
+	maxim,refout-load = <10>;
+
+	port {
+		max2175_0_ep: endpoint {
+			remote-endpoint = <&slave_rx_device>;
+		};
+	};
+
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml
new file mode 100644
index 000000000..90315e217
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml
@@ -0,0 +1,378 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2019 Renesas Electronics Corp.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim Integrated Quad GMSL Deserializer
+
+maintainers:
+  - Jacopo Mondi <jacopo+renesas@jmondi.org>
+  - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+  - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
+
+description: |
+  The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia
+  Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data
+  lanes.
+
+  In addition to video data, the GMSL links carry a bidirectional control
+  channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic
+  not addressed to itself to the other side of the links, where a GMSL
+  serializer will output it on a local I2C bus. In the other direction all I2C
+  traffic received over GMSL by the MAX9286 is output on the local I2C bus.
+
+properties:
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  compatible:
+    const: maxim,max9286
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  poc-supply:
+    description: Regulator providing Power over Coax to the cameras
+
+  enable-gpios:
+    description: GPIO connected to the \#PWDN pin with inverted polarity
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+  maxim,reverse-channel-microvolt:
+    minimum: 30000
+    maximum: 200000
+    default: 170000
+    description: |
+      Initial amplitude of the reverse control channel, in micro volts.
+
+      The initial amplitude shall be adjusted to a value compatible with the
+      configuration of the connected remote serializer.
+
+      Some camera modules (for example RDACM20) include an on-board MCU that
+      pre-programs the embedded serializer with power supply noise immunity
+      (high-threshold) enabled. A typical value of the deserializer's reverse
+      channel amplitude to communicate with pre-programmed serializers is
+      170000 micro volts.
+
+      A typical value for the reverse channel amplitude to communicate with
+      a remote serializer whose high-threshold noise immunity is not enabled
+      is 100000 micro volts
+
+  maxim,gpio-poc:
+    $ref: '/schemas/types.yaml#/definitions/uint32-array'
+    minItems: 2
+    maxItems: 2
+    description: |
+      Index of the MAX9286 gpio output line (0 or 1) that controls Power over
+      Coax to the cameras and its associated polarity flag.
+
+      The property accepts an array of two unsigned integers, the first being
+      the gpio line index (0 or 1) and the second being the gpio line polarity
+      flag (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW) as defined in
+      <include/dt-bindings/gpio/gpio.h>.
+
+      When the remote cameras power is controlled by one of the MAX9286 gpio
+      lines, this property has to be used to specify which line among the two
+      available ones controls the remote camera power enablement.
+
+      When this property is used it is not possible to register a gpio
+      controller as the gpio lines are controlled directly by the MAX9286 and
+      not available for consumers, nor the 'poc-supply' property should be
+      specified.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 0
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 1
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 2
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 3
+
+      port@4:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: CSI-2 Output
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes: true
+
+            required:
+              - data-lanes
+
+    required:
+      - port@4
+
+  i2c-mux:
+    type: object
+    $ref: /schemas/i2c/i2c-mux.yaml#
+    unevaluatedProperties: false
+    description: |
+      Each GMSL link is modelled as a child bus of an i2c bus multiplexer/switch.
+
+    patternProperties:
+      "^i2c@[0-3]$":
+        type: object
+        description: |
+          Child node of the i2c bus multiplexer which represents a GMSL link.
+          Each serializer device on the GMSL link remote end is represented with
+          an i2c-mux child node. The MAX9286 chip supports up to 4 GMSL
+          channels.
+
+        properties:
+          reg:
+            description: The index of the GMSL channel.
+            maxItems: 1
+
+        patternProperties:
+          "^camera@[a-f0-9]+$":
+            type: object
+            description: |
+              The remote camera device, composed by a GMSL serializer and a
+              connected video source.
+
+            properties:
+              compatible:
+                description: The remote device compatible string.
+
+              reg:
+                minItems: 2
+                maxItems: 3
+                description: |
+                  The I2C addresses to be assigned to the remote devices through
+                  address reprogramming. The number of entries depends on the
+                  requirements of the currently connected remote device.
+
+              port:
+                $ref: /schemas/graph.yaml#/properties/port
+                description: Connection to the MAX9286 sink.
+
+            required:
+              - compatible
+              - reg
+              - port
+
+            additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - ports
+  - i2c-mux
+
+# If 'maxim,gpio-poc' is present, then 'poc-supply' and 'gpio-controller'
+# are not allowed.
+if:
+  required:
+    - maxim,gpio-poc
+then:
+  properties:
+    poc-supply: false
+    gpio-controller: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c@e66d8000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        reg = <0 0xe66d8000>;
+
+        gmsl-deserializer@2c {
+            compatible = "maxim,max9286";
+            reg = <0x2c>;
+            poc-supply = <&camera_poc_12v>;
+            enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+
+            maxim,reverse-channel-microvolt = <170000>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    max9286_in0: endpoint {
+                        remote-endpoint = <&rdacm20_out0>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    max9286_in1: endpoint {
+                        remote-endpoint = <&rdacm20_out1>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+
+                    max9286_in2: endpoint {
+                        remote-endpoint = <&rdacm20_out2>;
+                    };
+                };
+
+                port@3 {
+                    reg = <3>;
+
+                    max9286_in3: endpoint {
+                        remote-endpoint = <&rdacm20_out3>;
+                    };
+                };
+
+                port@4 {
+                    reg = <4>;
+
+                    max9286_out: endpoint {
+                        data-lanes = <1 2 3 4>;
+                        remote-endpoint = <&csi40_in>;
+                    };
+                };
+            };
+
+            i2c-mux {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                i2c@0 {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    reg = <0>;
+
+                    camera@51 {
+                        compatible = "imi,rdacm20";
+                        reg = <0x51>, <0x61>;
+
+                        port {
+                            rdacm20_out0: endpoint {
+                                remote-endpoint = <&max9286_in0>;
+                            };
+                        };
+
+                    };
+                };
+
+                i2c@1 {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    reg = <1>;
+
+                    camera@52 {
+                        compatible = "imi,rdacm20";
+                        reg = <0x52>, <0x62>;
+
+                        port {
+                            rdacm20_out1: endpoint {
+                                remote-endpoint = <&max9286_in1>;
+                            };
+                        };
+                    };
+                };
+
+                i2c@2 {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    reg = <2>;
+
+                    camera@53 {
+                        compatible = "imi,rdacm20";
+                        reg = <0x53>, <0x63>;
+
+                        port {
+                            rdacm20_out2: endpoint {
+                                remote-endpoint = <&max9286_in2>;
+                            };
+                        };
+                    };
+                };
+
+                i2c@3 {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    reg = <3>;
+
+                    camera@54 {
+                        compatible = "imi,rdacm20";
+                        reg = <0x54>, <0x64>;
+
+                        port {
+                            rdacm20_out3: endpoint {
+                                remote-endpoint = <&max9286_in3>;
+                            };
+                        };
+                    };
+                };
+            };
+        };
+
+        /*
+        * Example of a deserializer that controls the camera Power over Coax
+        * through one of its gpio lines.
+        */
+        gmsl-deserializer@6c {
+            compatible = "maxim,max9286";
+            reg = <0x6c>;
+            enable-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+
+            /*
+            * The remote camera power is controlled by MAX9286 GPIO line #0.
+            * No 'poc-supply' nor 'gpio-controller' are specified.
+            */
+            maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+
+            /*
+            * Do not describe connections as they're the same as in the previous
+            * example.
+            */
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@4 {
+                    reg = <4>;
+                };
+            };
+
+            i2c-mux {
+                #address-cells = <1>;
+                #size-cells = <0>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml
new file mode 100644
index 000000000..444f24838
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml
@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2021 Renesas Electronics Corp.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/maxim,max96712.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Quad GMSL2 to CSI-2 Deserializer with GMSL1 Compatibility
+
+maintainers:
+  - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
+
+description: |
+  The MAX96712 deserializer converts GMSL2 or GMSL1 serial inputs into MIPI
+  CSI-2 D-PHY or C-PHY formatted outputs. The device allows each link to
+  simultaneously transmit bidirectional control-channel data while forward
+  video transmissions are in progress. The MAX96712 can accommodate as many as
+  four remotely located sensors using industry-standard coax or STP
+  interconnects.
+
+  Each GMSL2 serial link operates at a fixed rate of 3Gbps or 6Gbps in the
+  forward direction and 187.5Mbps in the reverse direction. In GMSL1 mode, the
+  MAX96712 can be paired with first-generation 3.12Gbps or 1.5Gbps GMSL1
+  serializers or operate up to 3.12Gbps with GMSL2 serializers in GMSL1 mode.
+
+properties:
+  compatible:
+    const: maxim,max96712
+
+  reg:
+    description: I2C device address
+    maxItems: 1
+
+  enable-gpios: true
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 0
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 1
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 2
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: GMSL Input 3
+
+      port@4:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: CSI-2 Output
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes: true
+
+            required:
+              - data-lanes
+
+    required:
+      - port@4
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c@e6508000 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            reg = <0 0xe6508000>;
+
+            gmsl0: gmsl-deserializer@49 {
+                    compatible = "maxim,max96712";
+                    reg = <0x49>;
+                    enable-gpios = <&pca9654_a 0 GPIO_ACTIVE_HIGH>;
+
+                    ports {
+                            #address-cells = <1>;
+                            #size-cells = <0>;
+
+                            port@4 {
+                                    reg = <4>;
+                                    max96712_out0: endpoint {
+                                            clock-lanes = <0>;
+                                            data-lanes = <1 2 3 4>;
+                                            remote-endpoint = <&csi40_in>;
+                                    };
+                            };
+                    };
+            };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt
new file mode 100644
index 000000000..060d2b7a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt
@@ -0,0 +1,20 @@
+* Melexis MLX90640 FIR Sensor
+
+Melexis MLX90640 FIR sensor support which allows recording of thermal data
+with 32x24 resolution excluding 2 lines of coefficient data that is used by
+userspace to render processed frames.
+
+Required Properties:
+ - compatible : Must be "melexis,mlx90640"
+ - reg : i2c address of the device
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		mlx90640@33 {
+			compatible = "melexis,mlx90640";
+			reg = <0x33>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml
new file mode 100644
index 000000000..39395ea8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml
@@ -0,0 +1,132 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2014--2020 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/mipi-ccs.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MIPI CCS, SMIA++ and SMIA compliant camera sensors
+
+maintainers:
+  - Sakari Ailus <sakari.ailus@linux.intel.com>
+
+description:
+
+  CCS (Camera Command Set) is a raw Bayer camera sensor standard defined by the
+  MIPI Alliance; see
+  <URL:https://www.mipi.org/specifications/camera-command-set>.
+
+  SMIA (Standard Mobile Imaging Architecture) is an image sensor standard
+  defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension of
+  that.
+
+  More detailed documentation can be found in
+  Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - const: mipi-ccs-1.1
+          - const: mipi-ccs
+      - items:
+          - const: mipi-ccs-1.0
+          - const: mipi-ccs
+      - const: nokia,smia
+
+  reg:
+    maxItems: 1
+
+  vana-supply:
+    description: Analogue voltage supply (VANA), sensor dependent.
+
+  vcore-supply:
+    description: Core voltage supply (VCore), sensor dependent.
+
+  vio-supply:
+    description: I/O voltage supply (VIO), sensor dependent.
+
+  clocks:
+    description: External clock to the sensor.
+    maxItems: 1
+
+  clock-frequency:
+    description: Frequency of the external clock to the sensor in Hz.
+
+  reset-gpios:
+    description: Reset GPIO. Also commonly called XSHUTDOWN in hardware
+      documentation.
+    maxItems: 1
+
+  flash-leds:
+    description: Flash LED phandles. See ../video-interfaces.txt for details.
+
+  lens-focus:
+    description: Lens focus controller phandles. See ../video-interfaces.txt
+      for details.
+
+  rotation:
+    description: Rotation of the sensor.  See ../video-interfaces.txt for
+      details.
+    enum: [ 0, 180 ]
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          link-frequencies: true
+          data-lanes: true
+          bus-type:
+            enum:
+              - 1 # CSI-2 C-PHY
+              - 3 # CCP2
+              - 4 # CSI-2 D-PHY
+
+        required:
+          - link-frequencies
+          - data-lanes
+          - bus-type
+
+required:
+  - compatible
+  - reg
+  - clock-frequency
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c2 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        clock-frequency = <400000>;
+
+        camera-sensor@10 {
+            compatible = "mipi-ccs-1.0", "mipi-ccs";
+            reg = <0x10>;
+            reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+            vana-supply = <&vaux3>;
+            clocks = <&omap3_isp 0>;
+            clock-frequency = <9600000>;
+            port {
+                ccs_ep: endpoint {
+                    data-lanes = <1 2>;
+                    remote-endpoint = <&csi2a_ep>;
+                    link-frequencies = /bits/ 64 <199200000 210000000
+                                                  499200000>;
+                    bus-type = <4>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt
new file mode 100644
index 000000000..c920552b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt
@@ -0,0 +1,38 @@
+MT9M001: 1/2-Inch Megapixel Digital Image Sensor
+
+The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital
+image sensor. It is programmable through I2C interface.
+
+Required Properties:
+
+- compatible: shall be "onnn,mt9m001".
+- clocks: reference to the master clock into sensor
+
+Optional Properties:
+
+- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
+  Active low.
+- standby-gpios: GPIO handle which is connected to the standby pin of the chip.
+  Active high.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	&i2c1 {
+		camera-sensor@5d {
+			compatible = "onnn,mt9m001";
+			reg = <0x5d>;
+			reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+			standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+			clocks = <&camera_clk>;
+			port {
+				mt9m001_out: endpoint {
+					remote-endpoint = <&vcap_in>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
new file mode 100644
index 000000000..d0bed6fa9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
@@ -0,0 +1,37 @@
+Micron 1.3Mp CMOS Digital Image Sensor
+
+The Micron MT9M111 is a CMOS active pixel digital image sensor with an active
+array size of 1280H x 1024V. It is programmable through a simple two-wire serial
+interface.
+
+Required Properties:
+- compatible: value should be "micron,mt9m111"
+- clocks: reference to the master clock.
+- clock-names: shall be "mclk".
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Optional endpoint properties:
+- pclk-sample: For information see ../video-interfaces.txt. The value is set to
+  0 if it isn't specified.
+
+Example:
+
+	i2c_master {
+		mt9m111@5d {
+			compatible = "micron,mt9m111";
+			reg = <0x5d>;
+			clocks = <&mclk>;
+			clock-names = "mclk";
+
+			port {
+				mt9m111_1: endpoint {
+					remote-endpoint = <&pxa_camera>;
+					pclk-sample = <1>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
new file mode 100644
index 000000000..100f0ae43
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
@@ -0,0 +1,41 @@
+* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor
+
+The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with
+an active array size of 752H x 480V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+
+- compatible: value should be either one among the following
+	(a) "aptina,mt9v022" for MT9V022 color sensor
+	(b) "aptina,mt9v022m" for MT9V022 monochrome sensor
+	(c) "aptina,mt9v024" for MT9V024 color sensor
+	(d) "aptina,mt9v024m" for MT9V024 monochrome sensor
+	(e) "aptina,mt9v032" for MT9V032 color sensor
+	(f) "aptina,mt9v032m" for MT9V032 monochrome sensor
+	(g) "aptina,mt9v034" for MT9V034 color sensor
+	(h) "aptina,mt9v034m" for MT9V034 monochrome sensor
+
+Optional Properties:
+
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+	expressed as a 64-bit big-endian integer.
+- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
+- standby-gpios: GPIO handle which is connected to the standby pin of the chip.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	mt9v032@5c {
+		compatible = "aptina,mt9v032";
+		reg = <0x5c>;
+
+		port {
+			mt9v032_out: endpoint {
+				link-frequencies = /bits/ 64
+					<13000000 26600000 27000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml
new file mode 100644
index 000000000..b617cc5c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/onnn,ar0521.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/onnn,ar0521.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ON Semiconductor AR0521 MIPI CSI-2 sensor
+
+maintainers:
+  - Krzysztof Hałasa <khalasa@piap.pl>
+
+description: |-
+  The AR0521 is a raw CMOS image sensor with MIPI CSI-2 and
+  I2C-compatible control interface.
+
+properties:
+  compatible:
+    const: onnn,ar0521
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: extclk
+
+  vaa-supply:
+    description:
+      Definition of the regulator used as analog (2.7 V) voltage supply.
+
+  vdd-supply:
+    description:
+      Definition of the regulator used as digital core (1.2 V) voltage supply.
+
+  vdd_io-supply:
+    description:
+      Definition of the regulator used as digital I/O (1.8 V) voltage supply.
+
+  reset-gpios:
+    description: reset GPIO, usually active low
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
+    description: |
+      Video output port.
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          bus-type:
+            const: 4
+          data-lanes:
+            anyOf:
+              - items:
+                  - const: 1
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - vaa-supply
+  - vdd-supply
+  - vdd_io-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/clock/imx6qdl-clock.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ar0521: camera-sensor@36 {
+                    compatible = "onnn,ar0521";
+                    reg = <0x36>;
+                    pinctrl-names = "default";
+                    pinctrl-0 = <&pinctrl_mipi_camera>;
+                    clocks = <&clks IMX6QDL_CLK_CKO>;
+                    clock-names = "extclk";
+                    reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+                    vaa-supply = <&reg_2p7v>;
+                    vdd-supply = <&reg_1p2v>;
+                    vdd_io-supply = <&reg_1p8v>;
+
+                    port {
+                           mipi_camera_to_mipi_csi2: endpoint {
+                                    remote-endpoint = <&mipi_csi2_in>;
+                                    data-lanes = <1 2 3 4>;
+                            };
+                    };
+            };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
new file mode 100644
index 000000000..989ce6cb6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2640 CMOS sensor
+
+The Omnivision OV2640 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov2640"
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+
+Optional Properties:
+- resetb-gpios: reference to the GPIO connected to the resetb pin, if any.
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov2640: camera@30 {
+			compatible = "ovti,ov2640";
+			reg = <0x30>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xvclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
new file mode 100644
index 000000000..92989a619
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
@@ -0,0 +1,47 @@
+* OV2659 1/5-Inch 2Mp SOC Camera
+
+The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of
+1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports
+multiple resolutions output, such as UXGA, SVGA, 720p. It also can support
+YUV422, RGB565/555 or raw RGB output formats.
+
+Required Properties:
+- compatible: Must be "ovti,ov2659"
+- reg: I2C slave address
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- link-frequencies: target pixel clock frequency.
+
+Optional Properties:
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active high with internal pull down resistor.
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active low with internal pull up resistor.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		 ov2659@30 {
+			compatible = "ovti,ov2659";
+			reg = <0x30>;
+
+			clocks = <&clk_ov2659 0>;
+			clock-names = "xvclk";
+
+			powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+
+			port {
+				ov2659_0: endpoint {
+					remote-endpoint = <&vpfe_ep>;
+					link-frequencies = /bits/ 64 <70000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2685.txt b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
new file mode 100644
index 000000000..625c4a8c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2685 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov2685"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.8 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1>".
+
+Example:
+&i2c7 {
+	ov2685: camera-sensor@3c {
+		compatible = "ovti,ov2685";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1800>;
+		reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+
+		port {
+			ucam_out: endpoint {
+				remote-endpoint = <&mipi_in_ucam>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
new file mode 100644
index 000000000..72ad992f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
@@ -0,0 +1,54 @@
+* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
+
+The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a serial I2C
+interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov5645".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin PWDNB which is physically active low.
+- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
+  the hardware pin RESETB.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov5645: ov5645@3c {
+			compatible = "ovti,ov5645";
+			reg = <0x3c>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <24000000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov5645_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0 2>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5695.txt b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
new file mode 100644
index 000000000..640a63717
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
@@ -0,0 +1,41 @@
+* Omnivision OV5695 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov5695"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.2 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1 2>".
+
+Example:
+&i2c7 {
+	ov5695: camera-sensor@36 {
+		compatible = "ovti,ov5695";
+		reg = <0x36>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1250_cam>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+
+		port {
+			wcam_out: endpoint {
+				remote-endpoint = <&mipi_in_wcam>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
new file mode 100644
index 000000000..8281151f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
@@ -0,0 +1,52 @@
+* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor
+
+The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor
+with an active array size of 640H x 480V. It is programmable through a serial
+I2C interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov7251".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin XSHUTDOWN which is physically active low.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node shall contain one 'port' child node with a single 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov7251: camera-sensor@60 {
+			compatible = "ovti,ov7251";
+			reg = <0x60>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_bw_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <24000000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov7251_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
new file mode 100644
index 000000000..2c972a56f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
@@ -0,0 +1,55 @@
+* Omnivision OV7670 CMOS sensor
+
+The Omnivision OV7670 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov7670"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+
+Required Endpoint Properties:
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is low.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+- ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output
+  signal during horizontal blankings.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov7670: camera@21 {
+			compatible = "ovti,ov7670";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			ov7670,pclk-hb-disable;
+
+			port {
+				ov7670_0: endpoint {
+					hsync-active = <0>;
+					vsync-active = <0>;
+
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
new file mode 100644
index 000000000..af781c3a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
@@ -0,0 +1,47 @@
+* Omnivision OV7740 CMOS image sensor
+
+The Omnivision OV7740 image sensor supports multiple output image
+size, such as VGA, and QVGA, CIF and any size smaller. It also
+supports the RAW RGB and YUV output formats.
+
+The common video interfaces bindings (see video-interfaces.txt) should
+be used to specify link to the image data receiver. The OV7740 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Required Properties:
+- compatible:	"ovti,ov7740".
+- reg:		I2C slave address of the sensor.
+- clocks:	Reference to the xvclk input clock.
+- clock-names:	"xvclk".
+
+Optional Properties:
+- reset-gpios: Rreference to the GPIO connected to the reset_b pin,
+  if any. Active low with pull-ip resistor.
+- powerdown-gpios: Reference to the GPIO connected to the pwdn pin,
+  if any. Active high with pull-down resistor.
+
+Endpoint node mandatory properties:
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+Example:
+
+	i2c1: i2c@fc028000 {
+		ov7740: camera@21 {
+			compatible = "ovti,ov7740";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+			clocks = <&isc>;
+			clock-names = "xvclk";
+			assigned-clocks = <&isc>;
+			assigned-clock-rates = <24000000>;
+			reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>;
+
+			port {
+				ov7740_0: endpoint {
+					remote-endpoint = <&isc_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov8856.yaml b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
new file mode 100644
index 000000000..baf92aaaf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov8856.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2019 MediaTek Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ov8856.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV8856 CMOS Sensor Device Tree Bindings
+
+maintainers:
+  - Dongchun Zhu <dongchun.zhu@mediatek.com>
+
+description: |-
+  The Omnivision OV8856 is a high performance, 1/4-inch, 8 megapixel, CMOS
+  image sensor that delivers 3264x2448 at 30fps. It provides full-frame,
+  sub-sampled, and windowed 10-bit MIPI images in various formats via the
+  Serial Camera Control Bus (SCCB) interface. This chip is programmable
+  through I2C and two-wire SCCB. The sensor output is available via CSI-2
+  serial data output (up to 4-lane).
+
+properties:
+  compatible:
+    const: ovti,ov8856
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    description:
+      Input clock for the sensor.
+    items:
+      - const: xvclk
+
+  clock-frequency:
+    description:
+      Frequency of the xvclk clock in Hertz.
+
+  dovdd-supply:
+    description:
+      Definition of the regulator used as interface power supply.
+
+  avdd-supply:
+    description:
+      Definition of the regulator used as analog power supply.
+
+  dvdd-supply:
+    description:
+      Definition of the regulator used as digital power supply.
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDOWN which is physically
+      active low.
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            description: |-
+              The driver only supports four-lane operation.
+            items:
+              - const: 1
+              - const: 2
+              - const: 3
+              - const: 4
+
+          link-frequencies:
+            description: Frequencies listed are driver, not h/w limitations.
+            maxItems: 2
+            items:
+              enum: [ 360000000, 180000000 ]
+
+        required:
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-frequency
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov8856: camera@10 {
+            compatible = "ovti,ov8856";
+            reg = <0x10>;
+
+            reset-gpios = <&pio 111 GPIO_ACTIVE_LOW>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&clk_24m_cam>;
+
+            clocks = <&cam_osc>;
+            clock-names = "xvclk";
+            clock-frequency = <19200000>;
+
+            avdd-supply = <&mt6358_vcama2_reg>;
+            dvdd-supply = <&mt6358_vcamd_reg>;
+            dovdd-supply = <&mt6358_vcamio_reg>;
+
+            port {
+                wcam_out: endpoint {
+                    remote-endpoint = <&mipi_in_wcam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <360000000>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ov9650.txt b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
new file mode 100644
index 000000000..506dfc528
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
@@ -0,0 +1,36 @@
+* Omnivision OV9650/OV9652 CMOS sensor
+
+Required Properties:
+- compatible: shall be one of
+	"ovti,ov9650"
+	"ovti,ov9652"
+- clocks: reference to the xvclk input clock.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is high.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+
+The device node shall contain one 'port' child node with one child 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+&i2c0 {
+	ov9650: camera@30 {
+		compatible = "ovti,ov9650";
+		reg = <0x30>;
+		reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>;
+		powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>;
+		clocks = <&xclk>;
+
+		port {
+			ov9650_0: endpoint {
+				remote-endpoint = <&vcap1_in0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
new file mode 100644
index 000000000..63a040944
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
@@ -0,0 +1,154 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings
+
+maintainers:
+  - Dongchun Zhu <dongchun.zhu@mediatek.com>
+
+description: |-
+  The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel
+  image sensor, which is the latest production derived from Omnivision's CMOS
+  image sensor technology. Ihis chip supports high frame rate speeds up to 30fps
+  @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The
+  sensor output is available via CSI-2 serial data output.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov02a10
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    description:
+      External clock for the sensor.
+    items:
+      - const: eclk
+
+  clock-frequency:
+    description:
+      Frequency of the eclk clock in Hz.
+
+  dovdd-supply:
+    description:
+      Definition of the regulator used as Digital I/O voltage supply.
+
+  avdd-supply:
+    description:
+      Definition of the regulator used as Analog voltage supply.
+
+  dvdd-supply:
+    description:
+      Definition of the regulator used as Digital core voltage supply.
+
+  powerdown-gpios:
+    description:
+      Must be the device tree identifier of the GPIO connected to the
+      PD_PAD pin. This pin is used to place the OV02A10 into standby mode
+      or shutdown mode. As the line needs to be high for the powerdown mode
+      to be active, it should be marked GPIO_ACTIVE_HIGH.
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      Must be the device tree identifier of the GPIO connected to the
+      RST_PD pin. If specified, it will be asserted during driver probe.
+      As the line needs to be low for the reset to be active, it should be
+      marked GPIO_ACTIVE_LOW.
+    maxItems: 1
+
+  rotation:
+    enum:
+      - 0    # Sensor Mounted Upright
+      - 180  # Sensor Mounted Upside Down
+    default: 0
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+    description:
+      Output port node, single endpoint describing the CSI-2 transmitter.
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          link-frequencies: true
+          ovti,mipi-clock-voltage:
+            $ref: "/schemas/types.yaml#/definitions/uint32"
+            description:
+              Definition of MIPI clock voltage unit. This entry corresponds to
+              the link speed defined by the 'link-frequencies' property.
+              If present, the value shall be in the range of 0-4.
+            default: 4
+
+        required:
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-frequency
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - powerdown-gpios
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov02a10: camera-sensor@3d {
+            compatible = "ovti,ov02a10";
+            reg = <0x3d>;
+
+            powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
+
+            clocks = <&ov02a10_clk>;
+            clock-names = "eclk";
+            clock-frequency = <24000000>;
+
+            rotation = <180>;
+
+            dovdd-supply = <&ov02a10_dovdd>;
+            avdd-supply = <&ov02a10_avdd>;
+            dvdd-supply = <&ov02a10_dvdd>;
+
+            port {
+                wcam_out: endpoint {
+                    link-frequencies = /bits/ 64 <390000000>;
+                    ovti,mipi-clock-voltage = <3>;
+                    remote-endpoint = <&mipi_in_wcam>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
new file mode 100644
index 000000000..cf456f8d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV2680 CMOS Sensor
+
+maintainers:
+  - Rui Miguel Silva <rmfrfs@gmail.com>
+
+description: |-
+  The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2
+  megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200)
+  camera. It provides full-frame, sub-sampled, or windowed 10-bit images in
+  various formats via the control of the Serial Camera Control Bus (SCCB)
+  interface. The OV2680 has an image array capable of operating at up to 30
+  frames per second (fps) in UXGA resolution.
+
+properties:
+  compatible:
+    const: ovti,ov2680
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: xvclk
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDOWN which is physically
+      active low.
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Definition of the regulator used as interface power supply.
+
+  avdd-supply:
+    description:
+      Definition of the regulator used as analog power supply.
+
+  dvdd-supply:
+    description:
+      Definition of the regulator used as digital power supply.
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description:
+      A node containing an output port node.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov2680: camera-sensor@36 {
+                compatible = "ovti,ov2680";
+                reg = <0x36>;
+                clocks = <&osc>;
+                clock-names = "xvclk";
+                reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+                dovdd-supply = <&sw2_reg>;
+                dvdd-supply = <&sw2_reg>;
+                avdd-supply = <&reg_peri_3p15v>;
+
+                port {
+                        ov2680_to_mipi: endpoint {
+                                remote-endpoint = <&mipi_from_sensor>;
+                        };
+                };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
new file mode 100644
index 000000000..540fd69ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
@@ -0,0 +1,154 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV5640 Image Sensor Device Tree Bindings
+
+maintainers:
+  - Steve Longerbeam <slongerbeam@gmail.com>
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov5640
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: XCLK Input Clock
+
+  clock-names:
+    const: xclk
+
+  AVDD-supply:
+    description: Analog voltage supply, 2.8 volts
+
+  DVDD-supply:
+    description: Digital core voltage supply, 1.5 volts
+
+  DOVDD-supply:
+    description: Digital I/O voltage supply, 1.8 volts
+
+  powerdown-gpios:
+    maxItems: 1
+    description: >
+      Reference to the GPIO connected to the powerdown pin, if any.
+
+  reset-gpios:
+    maxItems: 1
+    description: >
+      Reference to the GPIO connected to the reset pin, if any.
+
+  rotation:
+    enum:
+      - 0
+      - 180
+
+  port:
+    description: Digital Output Port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          clock-lanes:
+            const: 0
+
+          data-lanes:
+            minItems: 1
+            maxItems: 2
+            items:
+              enum: [1, 2]
+
+          bus-width:
+            enum: [8, 10]
+
+          data-shift:
+            enum: [0, 2]
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - AVDD-supply
+  - DVDD-supply
+  - DOVDD-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+      #include <dt-bindings/clock/imx6qdl-clock.h>
+      #include <dt-bindings/gpio/gpio.h>
+
+      i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          camera@3c {
+              compatible = "ovti,ov5640";
+              pinctrl-names = "default";
+              pinctrl-0 = <&pinctrl_ov5640>;
+              reg = <0x3c>;
+              clocks = <&clks IMX6QDL_CLK_CKO>;
+              clock-names = "xclk";
+              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+              DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+              powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+              reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+              rotation = <180>;
+
+              port {
+                  /* MIPI CSI-2 bus endpoint */
+                  ov5640_to_mipi_csi2: endpoint {
+                      remote-endpoint = <&mipi_csi2_from_ov5640>;
+                      clock-lanes = <0>;
+                      data-lanes = <1 2>;
+                  };
+              };
+          };
+      };
+
+  - |
+      i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          camera@3c {
+              compatible = "ovti,ov5640";
+              pinctrl-names = "default";
+              pinctrl-0 = <&pinctrl_ov5640>;
+              reg = <0x3c>;
+              clocks = <&clk_ext_camera>;
+              clock-names = "xclk";
+              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+              DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+
+              port {
+                  /* Parallel bus endpoint */
+                  ov5640_to_parallel: endpoint {
+                      remote-endpoint = <&parallel_from_ov5640>;
+                      bus-width = <8>;
+                      data-shift = <2>; /* lines 9:2 are used */
+                      hsync-active = <0>;
+                      vsync-active = <0>;
+                      pclk-sample = <1>;
+                  };
+              };
+          };
+      };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml
new file mode 100644
index 000000000..a2abed06a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5647.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV5647 raw image sensor
+
+maintainers:
+  - Dave Stevenson <dave.stevenson@raspberrypi.com>
+  - Jacopo Mondi <jacopo@jmondi.org>
+
+description: |-
+  The OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data
+  interfaces and CCI (I2C compatible) control bus.
+
+properties:
+  compatible:
+    const: ovti,ov5647
+
+  reg:
+    description: I2C device address.
+    maxItems: 1
+
+  clocks:
+    description: Reference to the xclk clock.
+    maxItems: 1
+
+  pwdn-gpios:
+    description: Reference to the GPIO connected to the pwdn pin. Active high.
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          clock-noncontinuous: true
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov5647: camera@36 {
+            compatible = "ovti,ov5647";
+            reg = <0x36>;
+            clocks = <&camera_clk>;
+            pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+
+            port {
+                camera_out: endpoint {
+                    remote-endpoint = <&csi1_ep1>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml
new file mode 100644
index 000000000..246dc5fec
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5648.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV5648 Image Sensor Device Tree Bindings
+
+maintainers:
+  - Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+
+properties:
+  compatible:
+    const: ovti,ov5648
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: XVCLK Clock
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clock-rates:
+    maxItems: 1
+
+  dvdd-supply:
+    description: Digital Domain Power Supply
+
+  avdd-supply:
+    description: Analog Domain Power Supply (internal AVDD is used if missing)
+
+  dovdd-supply:
+    description: I/O Domain Power Supply
+
+  powerdown-gpios:
+    maxItems: 1
+    description: Power Down Pin GPIO Control (active low)
+
+  reset-gpios:
+    maxItems: 1
+    description: Reset Pin GPIO Control (active low)
+
+  port:
+    description: MIPI CSI-2 transmitter port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          link-frequencies: true
+
+          data-lanes:
+            minItems: 1
+            maxItems: 2
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - assigned-clocks
+  - assigned-clock-rates
+  - dvdd-supply
+  - dovdd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun8i-v3s-ccu.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov5648: camera@36 {
+            compatible = "ovti,ov5648";
+            reg = <0x36>;
+
+            dvdd-supply = <&ov5648_dvdd>;
+            avdd-supply = <&ov5648_avdd>;
+            dovdd-supply = <&ov5648_dovdd>;
+            clocks = <&ov5648_xvclk 0>;
+            assigned-clocks = <&ov5648_xvclk 0>;
+            assigned-clock-rates = <24000000>;
+
+
+            ov5648_out: port {
+                ov5648_out_mipi_csi2: endpoint {
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <210000000 168000000>;
+
+                    remote-endpoint = <&mipi_csi2_in_ov5648>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
new file mode 100644
index 000000000..359dc0844
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml
@@ -0,0 +1,124 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2022 Amarulasolutions
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV5693 CMOS Sensor
+
+maintainers:
+  - Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
+
+description: |
+  The Omnivision OV5693 is a high performance, 1/4-inch, 5 megapixel, CMOS
+  image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
+  sub-sampled, and windowed 10-bit MIPI images in various formats via the
+  Serial Camera Control Bus (SCCB) interface.
+
+  OV5693 is controlled via I2C and two-wire Serial Camera Control Bus (SCCB).
+  The sensor output is available via CSI-2 serial data output (up to 2-lane).
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov5693
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      System input clock (aka XVCLK). From 6 to 27 MHz.
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Digital I/O voltage supply, 1.8V.
+
+  avdd-supply:
+    description:
+      Analog voltage supply, 2.8V.
+
+  dvdd-supply:
+    description:
+      Digital core voltage supply, 1.2V.
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDN which is physically
+      active low.
+    maxItems: 1
+
+  port:
+    description: MIPI CSI-2 transmitter port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          link-frequencies: true
+
+          data-lanes:
+            minItems: 1
+            maxItems: 2
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/pinctrl/rockchip.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov5693: camera@36 {
+            compatible = "ovti,ov5693";
+            reg = <0x36>;
+
+            reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&cif_clkout_m0>;
+
+            clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clock-rates = <19200000>;
+
+            avdd-supply = <&vcc_1v8>;
+            dvdd-supply = <&vcc_1v2>;
+            dovdd-supply = <&vcc_2v8>;
+
+            rotation = <90>;
+            orientation = <0>;
+
+            port {
+                ucam_out: endpoint {
+                    remote-endpoint = <&mipi_in_ucam>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <450000000>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml
new file mode 100644
index 000000000..44529425c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov772x.yaml
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov772x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV7720/OV7725 CMOS sensor
+
+maintainers:
+  - Jacopo Mondi <jacopo@jmondi.org>
+
+description: |
+  The Omnivision OV7720/OV7725 sensor supports multiple resolutions output,
+  such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can
+  support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats.
+
+properties:
+  compatible:
+    enum:
+      - ovti,ov7720
+      - ovti,ov7725
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  reset-gpios:
+    description: |
+      Reference to the GPIO connected to the RSTB pin which is active low.
+    maxItems: 1
+
+  powerdown-gpios:
+    description: |
+      Reference to the GPIO connected to the PWDN pin which is active high.
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    description: |
+      Video output port.
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          bus-type:
+            enum: [5, 6]
+
+          bus-width:
+            enum: [8, 10]
+            default: 10
+
+          data-shift:
+            enum: [0, 2]
+            default: 0
+
+          hsync-active:
+            enum: [0, 1]
+            default: 1
+
+          vsync-active:
+            enum: [0, 1]
+            default: 1
+
+          pclk-sample:
+            enum: [0, 1]
+            default: 1
+
+        allOf:
+          - if:
+              properties:
+                bus-type:
+                  const: 6
+            then:
+              properties:
+                hsync-active: false
+                vsync-active: false
+
+          - if:
+              properties:
+                bus-width:
+                  const: 10
+            then:
+              properties:
+                data-shift:
+                  const: 0
+
+        required:
+          - bus-type
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        ov772x: camera@21 {
+            compatible = "ovti,ov7725";
+            reg = <0x21>;
+            reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
+            powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
+            clocks = <&xclk>;
+
+            port {
+                ov772x_0: endpoint {
+                    bus-type = <5>;
+                    vsync-active = <0>;
+                    hsync-active = <0>;
+                    pclk-sample = <0>;
+                    bus-width = <8>;
+                    data-shift = <0>;
+                    remote-endpoint = <&vcap1_in0>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml
new file mode 100644
index 000000000..b962863e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml
@@ -0,0 +1,118 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV8865 Image Sensor Device Tree Bindings
+
+maintainers:
+  - Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+
+properties:
+  compatible:
+    const: ovti,ov8865
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: EXTCLK Clock
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clock-rates:
+    maxItems: 1
+
+  dvdd-supply:
+    description: Digital Domain Power Supply
+
+  avdd-supply:
+    description: Analog Domain Power Supply
+
+  dovdd-supply:
+    description: I/O Domain Power Supply
+
+  powerdown-gpios:
+    maxItems: 1
+    description: Power Down Pin GPIO Control (active low)
+
+  reset-gpios:
+    maxItems: 1
+    description: Reset Pin GPIO Control (active low)
+
+  port:
+    description: MIPI CSI-2 transmitter port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          link-frequencies: true
+
+          data-lanes:
+            minItems: 1
+            maxItems: 4
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - assigned-clocks
+  - assigned-clock-rates
+  - dvdd-supply
+  - avdd-supply
+  - dovdd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun8i-a83t-ccu.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c2 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov8865: camera@36 {
+            compatible = "ovti,ov8865";
+            reg = <0x36>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&csi_mclk_pin>;
+
+            clocks = <&ccu CLK_CSI_MCLK>;
+            assigned-clocks = <&ccu CLK_CSI_MCLK>;
+            assigned-clock-rates = <24000000>;
+
+            avdd-supply = <&reg_ov8865_avdd>;
+            dovdd-supply = <&reg_ov8865_dovdd>;
+            dvdd-supply = <&reg_ov8865_dvdd>;
+
+            powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */
+            reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+
+            port {
+                ov8865_out_mipi_csi2: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <360000000>;
+
+                    remote-endpoint = <&mipi_csi2_in_ov8865>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml
new file mode 100644
index 000000000..bf115ab9d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov9282.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2021 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov9282.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV9282 Sensor
+
+maintainers:
+  - Paul J. Murphy <paul.j.murphy@intel.com>
+  - Daniele Alessandrelli <daniele.alessandrelli@intel.com>
+
+description:
+  OV9282 sensor is an OmniVision black & white CMOS active pixel digital image
+  sensor with an active array size of 1296H x 816V. It is programmable through
+  I2C interface. The I2C client address is fixed to 0x60/0x70 as per sensor data
+  sheet. Image data is sent through MIPI CSI-2.
+
+properties:
+  compatible:
+    const: ovti,ov9282
+  reg:
+    description: I2C address
+    maxItems: 1
+
+  assigned-clocks: true
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+
+  clocks:
+    description: Clock frequency from 6 to 27MHz
+    maxItems: 1
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the XCLR pin, if any.
+    maxItems: 1
+
+  port:
+    additionalProperties: false
+    $ref: /schemas/graph.yaml#/$defs/port-base
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes: true
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@60 {
+            compatible = "ovti,ov9282";
+            reg = <0x60>;
+            clocks = <&ov9282_clk>;
+
+            assigned-clocks = <&ov9282_clk>;
+            assigned-clock-parents = <&ov9282_clk_parent>;
+            assigned-clock-rates = <24000000>;
+
+            port {
+                ov9282: endpoint {
+                    remote-endpoint = <&cam>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <800000000>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
new file mode 100644
index 000000000..4a3181a3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
@@ -0,0 +1,19 @@
+* Panasonic AMG88xx
+
+The Panasonic family of AMG88xx Grid-Eye sensors allow recording
+8x8 10Hz video which consists of thermal datapoints
+
+Required Properties:
+ - compatible : Must be "panasonic,amg88xx"
+ - reg : i2c address of the device
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		amg88xx@69 {
+			compatible = "panasonic,amg88xx";
+			reg = <0x69>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml
new file mode 100644
index 000000000..f50e54a72
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/rda,rda5807.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Unisoc Communications RDA5807 FM radio receiver
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  compatible:
+    enum:
+      - rda,rda5807
+
+  reg:
+    description: I2C address.
+    maxItems: 1
+
+  power-supply: true
+
+  rda,lnan:
+    description: Use LNAN input port.
+    type: boolean
+
+  rda,lnap:
+    description: Use LNAP input port.
+    type: boolean
+
+  rda,analog-out:
+    description: Enable analog audio output.
+    type: boolean
+
+  rda,i2s-out:
+    description: Enable I2S digital audio output.
+    type: boolean
+
+  rda,lna-microamp:
+    description: LNA working current, in micro-amperes.
+    default: 2500
+    enum: [1800, 2100, 2500, 3000]
+
+required:
+  - compatible
+  - reg
+  - power-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      radio@11 {
+        compatible = "rda,rda5807";
+        reg = <0x11>;
+
+        power-supply = <&ldo6>;
+
+        rda,lnan;
+        rda,lnap;
+        rda,analog-out;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml
new file mode 100644
index 000000000..c9760f895
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.yaml
@@ -0,0 +1,125 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx214.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/3.06-Inch 13.13MP CMOS Digital Image Sensor
+
+maintainers:
+  - Ricardo Ribalda <ribalda@kernel.org>
+
+description: |
+  The Sony IMX214 is a 1/3.06-inch CMOS active pixel digital image sensor with
+  an active array size of 4224H x 3200V. It is programmable through an I2C
+  interface. Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a
+  maximum throughput of 1.2Gbps/lane.
+
+allOf:
+  - $ref: ../video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: sony,imx214
+
+  reg:
+    enum:
+      - 0x10
+      - 0x1a
+
+  clocks:
+    description: Reference to the xclk clock.
+    maxItems: 1
+
+  clock-frequency:
+    description: Frequency of the xclk clock in Hz.
+
+  enable-gpios:
+    description: GPIO descriptor for the enable pin.
+    maxItems: 1
+
+  vdddo-supply:
+    description: Chip digital IO regulator (1.8V).
+
+  vdda-supply:
+    description: Chip analog regulator (2.7V).
+
+  vddd-supply:
+    description: Chip digital core regulator (1.12V).
+
+  flash-leds: true
+  lens-focus: true
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    description: |
+      Video output port.
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            anyOf:
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-frequency
+  - enable-gpios
+  - vdddo-supply
+  - vdda-supply
+  - vddd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera-sensor@1a {
+            compatible = "sony,imx214";
+            reg = <0x1a>;
+            vdddo-supply = <&pm8994_lvs1>;
+            vddd-supply = <&camera_vddd_1v12>;
+            vdda-supply = <&pm8994_l17>;
+            lens-focus = <&ad5820>;
+            enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
+            clocks = <&camera_clk>;
+            clock-frequency = <24000000>;
+
+            port {
+                imx214_ep: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <480000000>;
+                    remote-endpoint = <&csiphy0_ep>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml
new file mode 100644
index 000000000..4271fc3cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx274.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx274.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/2.5-Inch 8.51MP CMOS Digital Image Sensor
+
+maintainers:
+  - Leon Luo <leonl@leopardimaging.com>
+
+description: |
+  The Sony IMX274 is a 1/2.5-inch CMOS active pixel digital image sensor with an
+  active array size of 3864H x 2202V. It is programmable through I2C interface.
+  Image data is sent through MIPI CSI-2, which is configured as 4 lanes at 1440
+  Mbps.
+
+properties:
+  compatible:
+    const: sony,imx274
+
+  reg:
+    const: 0x1a
+
+  reset-gpios:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: inck
+
+  vana-supply:
+    description: Sensor 2.8 V analog supply.
+
+  vdig-supply:
+    description: Sensor 1.8 V digital core supply.
+
+  vddl-supply:
+    description: Sensor digital IO 1.2 V supply.
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx274: camera-sensor@1a {
+            compatible = "sony,imx274";
+            reg = <0x1a>;
+            reset-gpios = <&gpio_sensor 0 0>;
+
+            port {
+                sensor_out: endpoint {
+                    remote-endpoint = <&csiss_in>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml
new file mode 100644
index 000000000..f5055b9db
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml
@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2021 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx334.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX334 Sensor
+
+maintainers:
+  - Paul J. Murphy <paul.j.murphy@intel.com>
+  - Daniele Alessandrelli <daniele.alessandrelli@intel.com>
+
+description:
+  IMX334 sensor is a Sony CMOS active pixel digital image sensor with an active
+  array size of 3864H x 2202V. It is programmable through I2C interface. The
+  I2C client address is fixed to 0x1a as per sensor data sheet. Image data is
+  sent through MIPI CSI-2.
+
+properties:
+  compatible:
+    const: sony,imx334
+  reg:
+    description: I2C address
+    maxItems: 1
+
+  assigned-clocks: true
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+
+  clocks:
+    description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz
+    maxItems: 1
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the XCLR pin, if any.
+
+  port:
+    additionalProperties: false
+    $ref: /schemas/graph.yaml#/$defs/port-base
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes: true
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@1a {
+            compatible = "sony,imx334";
+            reg = <0x1a>;
+            clocks = <&imx334_clk>;
+
+            assigned-clocks = <&imx334_clk>;
+            assigned-clock-parents = <&imx334_clk_parent>;
+            assigned-clock-rates = <24000000>;
+
+            port {
+                imx334: endpoint {
+                    remote-endpoint = <&cam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <891000000>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml
new file mode 100644
index 000000000..cf2ca2702
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx335.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2021 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx335.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX335 Sensor
+
+maintainers:
+  - Paul J. Murphy <paul.j.murphy@intel.com>
+  - Daniele Alessandrelli <daniele.alessandrelli@intel.com>
+
+description:
+  IMX335 sensor is a Sony CMOS active pixel digital image sensor with an active
+  array size of 2592H x 1944V. It is programmable through I2C interface. The
+  I2C client address is fixed to 0x1a as per sensor data sheet. Image data is
+  sent through MIPI CSI-2.
+
+properties:
+  compatible:
+    const: sony,imx335
+  reg:
+    description: I2C address
+    maxItems: 1
+
+  assigned-clocks: true
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+
+  clocks:
+    description: Clock frequency from 6 to 27 MHz, 37.125MHz, 74.25MHz
+    maxItems: 1
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the XCLR pin, if any.
+    maxItems: 1
+
+  port:
+    additionalProperties: false
+    $ref: /schemas/graph.yaml#/$defs/port-base
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes: true
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@1a {
+            compatible = "sony,imx335";
+            reg = <0x1a>;
+            clocks = <&imx335_clk>;
+
+            assigned-clocks = <&imx335_clk>;
+            assigned-clock-parents = <&imx335_clk_parent>;
+            assigned-clock-rates = <24000000>;
+
+            port {
+                imx335: endpoint {
+                    remote-endpoint = <&cam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <594000000>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml
new file mode 100644
index 000000000..26d1807d0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx412.yaml
@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2021 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx412.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX412 Sensor
+
+maintainers:
+  - Paul J. Murphy <paul.j.murphy@intel.com>
+  - Daniele Alessandrelli <daniele.alessandrelli@intel.com>
+
+description:
+  IMX412 sensor is a Sony CMOS active pixel digital image sensor with an active
+  array size of 4072H x 3176V. It is programmable through I2C interface. The
+  I2C client address is fixed to 0x1a as per sensor data sheet. Image data is
+  sent through MIPI CSI-2.
+
+properties:
+  compatible:
+    const: sony,imx412
+  reg:
+    description: I2C address
+    maxItems: 1
+
+  assigned-clocks: true
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+
+  clocks:
+    description: Clock frequency 6MHz, 12MHz, 18MHz, 24MHz or 27MHz
+    maxItems: 1
+
+  dovdd-supply:
+    description: Interface power supply.
+
+  avdd-supply:
+    description: Analog power supply.
+
+  dvdd-supply:
+    description: Digital power supply.
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the XCLR pin, if any.
+    maxItems: 1
+
+  port:
+    additionalProperties: false
+    $ref: /schemas/graph.yaml#/$defs/port-base
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes: true
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@1a {
+            compatible = "sony,imx412";
+            reg = <0x1a>;
+            clocks = <&imx412_clk>;
+
+            assigned-clocks = <&imx412_clk>;
+            assigned-clock-parents = <&imx412_clk_parent>;
+            assigned-clock-rates = <24000000>;
+
+            port {
+                imx412: endpoint {
+                    remote-endpoint = <&cam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <600000000>;
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
new file mode 100644
index 000000000..7976e6c40
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
@@ -0,0 +1,82 @@
+STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
+
+MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
+time. Active port input stream will be de-serialized and its content outputted
+through PARALLEL output port.
+CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
+input port is a single lane 800Mbps. Both ports support clock and data lane
+polarity swap. First port also supports data lane swap.
+PARALLEL output port has a maximum width of 12 bits.
+Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
+YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
+
+Required Properties:
+- compatible: shall be "st,st-mipid02"
+- clocks: reference to the xclk input clock.
+- clock-names: shall be "xclk".
+- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
+- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
+	       This is an active low signal to the mipid02.
+
+Required subnodes:
+  - ports: A ports node with one port child node per device input and output
+	   port, in accordance with the video interface bindings defined in
+	   Documentation/devicetree/bindings/media/video-interfaces.txt. The
+	   port nodes are numbered as follows:
+
+	   Port Description
+	   -----------------------------
+	   0    CSI-2 first input port
+	   1    CSI-2 second input port
+	   2    PARALLEL output
+
+Endpoint node required property for CSI-2 connection is:
+- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be
+<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>.
+Endpoint node optional property for CSI-2 connection is:
+- lane-polarities: any lane can be inverted or not.
+
+Endpoint node required property for PARALLEL connection is:
+- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
+Endpoint node optional properties for PARALLEL connection are:
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+LOW being the default.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+LOW being the default.
+
+Example:
+
+mipid02: csi2rx@14 {
+	compatible = "st,st-mipid02";
+	reg = <0x14>;
+	status = "okay";
+	clocks = <&clk_ext_camera_12>;
+	clock-names = "xclk";
+	VDDE-supply = <&vdd>;
+	VDDIN-supply = <&vdd>;
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+
+			ep0: endpoint {
+				data-lanes = <1 2>;
+				remote-endpoint = <&mipi_csi2_in>;
+			};
+		};
+		port@2 {
+			reg = <2>;
+
+			ep2: endpoint {
+				bus-width = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				remote-endpoint = <&parallel_out>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
new file mode 100644
index 000000000..59102edcf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
@@ -0,0 +1,48 @@
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+		       source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+	      or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+		       MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+		    expressed as a 64-bit big-endian integer. The frequency
+		    is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	tc358743@f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
new file mode 100644
index 000000000..e76167999
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
@@ -0,0 +1,178 @@
+Device-Tree bindings for the NXP TDA1997x HDMI receiver
+
+The TDA19971/73 are HDMI video receivers.
+
+The TDA19971 Video port output pins can be used as follows:
+ - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
+ - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
+ - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
+ - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
+ - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
+ - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
+ - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The TDA19973 Video port output pins can be used as follows:
+ - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
+ - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
+ - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The Video port output pins are mapped via 4-bit 'pin groups' allowing
+for a variety of connection possibilities including swapping pin order within
+pin groups. The video_portcfg device-tree property consists of register mapping
+pairs which map a chip-specific VP output register to a 4-bit pin group. If
+the pin group needs to be bit-swapped you can use the *_S pin-group defines.
+
+Required Properties:
+ - compatible          :
+  - "nxp,tda19971" for the TDA19971
+  - "nxp,tda19973" for the TDA19973
+ - reg                 : I2C slave address
+ - interrupts          : The interrupt number
+ - DOVDD-supply        : Digital I/O supply
+ - DVDD-supply         : Digital Core supply
+ - AVDD-supply         : Analog supply
+ - nxp,vidout-portcfg  : array of pairs mapping VP output pins to pin groups.
+
+Optional Properties:
+ - nxp,audout-format   : DAI bus format: "i2s" or "spdif".
+ - nxp,audout-width    : width of audio output data bus (1-4).
+ - nxp,audout-layout   : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
+ - nxp,audout-mclk-fs  : Multiplication factor between stream rate and codec
+                         mclk.
+
+The port node shall contain one endpoint child node for its digital
+output video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Optional Endpoint Properties:
+  The following three properties are defined in video-interfaces.txt and
+  are valid for the output parallel bus endpoint:
+  - hsync-active: Horizontal synchronization polarity. Defaults to active high.
+  - vsync-active: Vertical synchronization polarity. Defaults to active high.
+  - data-active: Data polarity. Defaults to active high.
+
+Examples:
+ - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
+		 * 2 pixclk cycles.
+		 */
+		nxp,vidout-portcfg =
+			/* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
+			/* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
new file mode 100644
index 000000000..285f6ae7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
@@ -0,0 +1,19 @@
+* Texas Instruments THS8200 video encoder
+
+The ths8200 device is a digital to analog converter used in DVD players, video
+recorders, set-top boxes.
+
+Required Properties :
+- compatible : value must be "ti,ths8200"
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		ths8200@5c {
+			compatible = "ti,ths8200";
+			reg = <0x5c>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
new file mode 100644
index 000000000..e80d5891b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
@@ -0,0 +1,55 @@
+Toshiba et8ek8 5MP sensor
+
+Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "toshiba,et8ek8"
+- reg: I2C address (0x3e, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), 2.8 volts
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor. Camera
+  driver will set this frequency on the external clock. The clock frequency is
+  a pre-determined frequency known to be suitable to the board.
+- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor
+  is in hardware standby mode when the signal is in the low state.
+
+
+Optional properties
+-------------------
+
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	cam1: camera@3e {
+		compatible = "toshiba,et8ek8";
+		reg = <0x3e>;
+		vana-supply = <&vaux4>;
+		clocks = <&isp 0>;
+		clock-frequency = <9600000>;
+		reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
+		port {
+			csi_cam1: endpoint {
+				remote-endpoint = <&csi_out1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
new file mode 100644
index 000000000..46752cc71
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
@@ -0,0 +1,44 @@
+* Texas Instruments TVP514x video decoder
+
+The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip
+digital video decoder that digitizes and decodes all popular baseband analog
+video formats into digital video component. The tvp514x decoder supports analog-
+to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
+conversion and decoding of NTSC, PAL and SECAM composite and S-video into
+component YCbCr.
+
+Required Properties :
+- compatible : value should be either one among the following
+	(a) "ti,tvp5146" for tvp5146 decoder.
+	(b) "ti,tvp5146m2" for tvp5146m2 decoder.
+	(c) "ti,tvp5147" for tvp5147 decoder.
+	(d) "ti,tvp5147m1" for tvp5147m1 decoder.
+
+- hsync-active: HSYNC Polarity configuration for endpoint.
+
+- vsync-active: VSYNC Polarity configuration for endpoint.
+
+- pclk-sample: Clock polarity of the endpoint.
+
+For further reading on port node refer to Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp514x@5c {
+			compatible = "ti,tvp5146";
+			reg = <0x5c>;
+
+			port {
+				tvp514x_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
new file mode 100644
index 000000000..719b2995d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -0,0 +1,157 @@
+* Texas Instruments TVP5150 and TVP5151 video decoders
+
+The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+Required Properties:
+====================
+- compatible:	Value must be "ti,tvp5150".
+- reg:		I2C slave address.
+
+Optional Properties:
+====================
+- pdn-gpios:	Phandle for the GPIO connected to the PDN pin, if any.
+- reset-gpios:	Phandle for the GPIO connected to the RESETB pin, if any.
+
+The device node must contain one 'port' child node per device physical input
+and output port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows
+
+	  Name		Type		Port
+	--------------------------------------
+	  AIP1A		sink		0
+	  AIP1B		sink		1
+	  Y-OUT		src		2
+
+The device node must contain at least one sink port and the src port. Each input
+port must be linked to an endpoint defined in [1]. The port/connector layout is
+as follows
+
+tvp-5150 port@0 (AIP1A)
+	endpoint@0 -----------> Comp0-Con  port
+	endpoint@1 ------+----> Svideo-Con port
+tvp-5150 port@1 (AIP1B)  |
+	endpoint@1 ------+
+	endpoint@0 -----------> Comp1-Con  port
+tvp-5150 port@2
+	endpoint (video bitstream output at YOUT[0-7] parallel bus)
+
+Required Endpoint Properties for parallel synchronization on output port:
+=========================================================================
+
+- hsync-active:		Active state of the HSYNC signal. Must be <1> (HIGH).
+- vsync-active:		Active state of the VSYNC signal. Must be <1> (HIGH).
+- field-even-active:	Field signal level during the even field data
+			transmission. Must be <0>.
+
+Note: Do not specify any of these properties if you want to use the embedded
+      BT.656 synchronization.
+
+Optional Connector Properties:
+==============================
+
+- sdtv-standards: Set the possible signals to which the hardware tries to lock
+                  instead of using the autodetection mechnism. Please look at
+                  [1] for more information.
+
+[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml.
+
+Example - three input sources:
+#include <dt-bindings/display/sdtv-standards.h>
+
+comp_connector_0 {
+	compatible = "composite-video-connector";
+	label = "Composite0";
+	sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */
+
+	port {
+		composite0_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite0>;
+		};
+	};
+};
+
+comp_connector_1 {
+	compatible = "composite-video-connector";
+	label = "Composite1";
+	sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */
+
+	port {
+		composite1_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite1>;
+		};
+	};
+};
+
+svideo_connector {
+	compatible = "svideo-connector";
+	label = "S-Video";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		svideo_luma_to_tvp5150: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&tvp5150_to_svideo_luma>;
+		};
+
+		svideo_chroma_to_tvp5150: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&tvp5150_to_svideo_chroma>;
+		};
+	};
+};
+
+&i2c2 {
+	tvp5150@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			tvp5150_to_composite0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&composite0_to_tvp5150>;
+			};
+
+			tvp5150_to_svideo_luma: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&svideo_luma_to_tvp5150>;
+			};
+		};
+
+		port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			tvp5150_to_composite1: endpoint@0 {
+				reg = <0>;
+                                remote-endpoint = <&composite1_to_tvp5150>;
+			};
+
+			tvp5150_to_svideo_chroma: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&svideo_chroma_to_tvp5150>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			tvp5150_1: endpoint {
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
new file mode 100644
index 000000000..5f28b5d9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
@@ -0,0 +1,53 @@
+* Texas Instruments TV7002 video decoder
+
+The TVP7002 device supports digitizing of video and graphics signal in RGB and
+YPbPr color space.
+
+Required Properties :
+- compatible : Must be "ti,tvp7002"
+
+Optional Properties:
+- hsync-active: HSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- vsync-active: VSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- pclk-sample: Clock polarity of the bus. Default value when this property is
+  not specified is <0>.
+
+- sync-on-green-active: Active state of Sync-on-green signal property of the
+  endpoint.
+  0 = Normal Operation (Active Low, Default)
+  1 = Inverted operation
+
+- field-even-active: Active-high Field ID output polarity control of the bus.
+  Under normal operation, the field ID output is set to logic 1 for an odd field
+  (field 1) and set to logic 0 for an even field (field 0).
+  0 = Normal Operation (Active Low, Default)
+  1 = FID output polarity inverted
+
+For further reading of port node refer Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp7002@5c {
+			compatible = "ti,tvp7002";
+			reg = <0x5c>;
+
+			port {
+				tvp7002_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+					sync-on-green-active = <1>;
+					field-even-active = <0>;
+				};
+			};
+		};
+		...
+	};