Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 96 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts
new file mode 100644
index 000000000..df2ca6d95
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Netgear WG302v2 based on IXP422BB
+ * Derived from boardfiles written by Imre Kaloz
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear WG302 v1";
+	compatible = "netgear,wg302v1", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM according to boot arguments */
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		/* The RedBoot comes up in 9600 baud so let's keep this */
+		bootargs = "console=ttyS0,9600n8";
+		stdout-path = "uart1:9600n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 64 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
+			<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
+			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
+			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
+			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
+			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
+		};
+
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy30>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy30: ethernet-phy@30 {
+					reg = <30>;
+				};
+			};
+		};
+	};
+};