Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 139 insertions, 0 deletions

diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
new file mode 100644
index 000000000..e929aaa74
--- /dev/null
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson SA
+ *
+ * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
+ */
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/arm-gic.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/arm-ux500-pm.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/regulator/machine.h>
+
+#include <asm/outercache.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/mach/map.h>
+#include <asm/mach/arch.h>
+
+#include "db8500-regs.h"
+#include "pm_domains.h"
+
+static int __init ux500_l2x0_unlock(void)
+{
+	int i;
+	struct device_node *np;
+	void __iomem *l2x0_base;
+
+	np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+	l2x0_base = of_iomap(np, 0);
+	of_node_put(np);
+	if (!l2x0_base)
+		return -ENODEV;
+
+	/*
+	 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
+	 * apparently locks both caches before jumping to the kernel. The
+	 * l2x0 core will not touch the unlock registers if the l2x0 is
+	 * already enabled, so we do it right here instead. The PL310 has
+	 * 8 sets of registers, one per possible CPU.
+	 */
+	for (i = 0; i < 8; i++) {
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+	}
+	iounmap(l2x0_base);
+	return 0;
+}
+
+static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
+{
+	/*
+	 * We can't write to secure registers as we are in non-secure
+	 * mode, until we have some SMI service available.
+	 */
+}
+
+/*
+ * FIXME: Should we set up the GPIO domain here?
+ *
+ * The problem is that we cannot put the interrupt resources into the platform
+ * device until the irqdomain has been added. Right now, we set the GIC interrupt
+ * domain from init_irq(), then load the gpio driver from
+ * core_initcall(nmk_gpio_init) and add the platform devices from
+ * arch_initcall(customize_machine).
+ *
+ * This feels fragile because it depends on the gpio device getting probed
+ * _before_ any device uses the gpio interrupts.
+*/
+static void __init ux500_init_irq(void)
+{
+	struct device_node *np;
+	struct resource r;
+
+	irqchip_init();
+	prcmu_early_init();
+	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
+	of_address_to_resource(np, 0, &r);
+	of_node_put(np);
+	if (!r.start) {
+		pr_err("could not find PRCMU base resource\n");
+		return;
+	}
+	ux500_pm_init(r.start, r.end-r.start);
+
+	/* Unlock before init */
+	ux500_l2x0_unlock();
+	outer_cache.write_sec = ux500_l2c310_write_sec;
+}
+
+static void ux500_restart(enum reboot_mode mode, const char *cmd)
+{
+	local_irq_disable();
+	local_fiq_disable();
+
+	prcmu_system_reset(0);
+}
+
+static const struct of_device_id u8500_local_bus_nodes[] = {
+	/* only create devices below soc node */
+	{ .compatible = "stericsson,db8500", },
+	{ .compatible = "simple-bus"},
+	{ },
+};
+
+static void __init u8500_init_machine(void)
+{
+	/* Initialize ux500 power domains */
+	ux500_pm_domains_init();
+
+	of_platform_populate(NULL, u8500_local_bus_nodes,
+			     NULL, NULL);
+}
+
+static const char * stericsson_dt_platform_compat[] = {
+	"st-ericsson,u8500",
+	"st-ericsson,u9500",
+	NULL,
+};
+
+DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
+	.l2c_aux_val    = 0,
+	.l2c_aux_mask	= ~0,
+	.init_irq	= ux500_init_irq,
+	.init_machine	= u8500_init_machine,
+	.dt_compat      = stericsson_dt_platform_compat,
+	.restart        = ux500_restart,
+MACHINE_END