Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 2105 insertions, 0 deletions

diff --git a/drivers/clk/tegra/clk-dfll.c b/drivers/clk/tegra/clk-dfll.c
new file mode 100644
index 000000000..41433927b
--- /dev/null
+++ b/drivers/clk/tegra/clk-dfll.c
@@ -0,0 +1,2105 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * clk-dfll.c - Tegra DFLL clock source common code
+ *
+ * Copyright (C) 2012-2019 NVIDIA Corporation. All rights reserved.
+ *
+ * Aleksandr Frid <afrid@nvidia.com>
+ * Paul Walmsley <pwalmsley@nvidia.com>
+ *
+ * This library is for the DVCO and DFLL IP blocks on the Tegra124
+ * SoC. These IP blocks together are also known at NVIDIA as
+ * "CL-DVFS". To try to avoid confusion, this code refers to them
+ * collectively as the "DFLL."
+ *
+ * The DFLL is a root clocksource which tolerates some amount of
+ * supply voltage noise. Tegra124 uses it to clock the fast CPU
+ * complex when the target CPU speed is above a particular rate. The
+ * DFLL can be operated in either open-loop mode or closed-loop mode.
+ * In open-loop mode, the DFLL generates an output clock appropriate
+ * to the supply voltage. In closed-loop mode, when configured with a
+ * target frequency, the DFLL minimizes supply voltage while
+ * delivering an average frequency equal to the target.
+ *
+ * Devices clocked by the DFLL must be able to tolerate frequency
+ * variation. In the case of the CPU, it's important to note that the
+ * CPU cycle time will vary. This has implications for
+ * performance-measurement code and any code that relies on the CPU
+ * cycle time to delay for a certain length of time.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pm_opp.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/seq_file.h>
+
+#include "clk-dfll.h"
+#include "cvb.h"
+
+/*
+ * DFLL control registers - access via dfll_{readl,writel}
+ */
+
+/* DFLL_CTRL: DFLL control register */
+#define DFLL_CTRL			0x00
+#define DFLL_CTRL_MODE_MASK		0x03
+
+/* DFLL_CONFIG: DFLL sample rate control */
+#define DFLL_CONFIG			0x04
+#define DFLL_CONFIG_DIV_MASK		0xff
+#define DFLL_CONFIG_DIV_PRESCALE	32
+
+/* DFLL_PARAMS: tuning coefficients for closed loop integrator */
+#define DFLL_PARAMS			0x08
+#define DFLL_PARAMS_CG_SCALE		(0x1 << 24)
+#define DFLL_PARAMS_FORCE_MODE_SHIFT	22
+#define DFLL_PARAMS_FORCE_MODE_MASK	(0x3 << DFLL_PARAMS_FORCE_MODE_SHIFT)
+#define DFLL_PARAMS_CF_PARAM_SHIFT	16
+#define DFLL_PARAMS_CF_PARAM_MASK	(0x3f << DFLL_PARAMS_CF_PARAM_SHIFT)
+#define DFLL_PARAMS_CI_PARAM_SHIFT	8
+#define DFLL_PARAMS_CI_PARAM_MASK	(0x7 << DFLL_PARAMS_CI_PARAM_SHIFT)
+#define DFLL_PARAMS_CG_PARAM_SHIFT	0
+#define DFLL_PARAMS_CG_PARAM_MASK	(0xff << DFLL_PARAMS_CG_PARAM_SHIFT)
+
+/* DFLL_TUNE0: delay line configuration register 0 */
+#define DFLL_TUNE0			0x0c
+
+/* DFLL_TUNE1: delay line configuration register 1 */
+#define DFLL_TUNE1			0x10
+
+/* DFLL_FREQ_REQ: target DFLL frequency control */
+#define DFLL_FREQ_REQ			0x14
+#define DFLL_FREQ_REQ_FORCE_ENABLE	(0x1 << 28)
+#define DFLL_FREQ_REQ_FORCE_SHIFT	16
+#define DFLL_FREQ_REQ_FORCE_MASK	(0xfff << DFLL_FREQ_REQ_FORCE_SHIFT)
+#define FORCE_MAX			2047
+#define FORCE_MIN			-2048
+#define DFLL_FREQ_REQ_SCALE_SHIFT	8
+#define DFLL_FREQ_REQ_SCALE_MASK	(0xff << DFLL_FREQ_REQ_SCALE_SHIFT)
+#define DFLL_FREQ_REQ_SCALE_MAX		256
+#define DFLL_FREQ_REQ_FREQ_VALID	(0x1 << 7)
+#define DFLL_FREQ_REQ_MULT_SHIFT	0
+#define DFLL_FREQ_REG_MULT_MASK		(0x7f << DFLL_FREQ_REQ_MULT_SHIFT)
+#define FREQ_MAX			127
+
+/* DFLL_DROOP_CTRL: droop prevention control */
+#define DFLL_DROOP_CTRL			0x1c
+
+/* DFLL_OUTPUT_CFG: closed loop mode control registers */
+/* NOTE: access via dfll_i2c_{readl,writel} */
+#define DFLL_OUTPUT_CFG			0x20
+#define DFLL_OUTPUT_CFG_I2C_ENABLE	(0x1 << 30)
+#define OUT_MASK			0x3f
+#define DFLL_OUTPUT_CFG_SAFE_SHIFT	24
+#define DFLL_OUTPUT_CFG_SAFE_MASK	\
+		(OUT_MASK << DFLL_OUTPUT_CFG_SAFE_SHIFT)
+#define DFLL_OUTPUT_CFG_MAX_SHIFT	16
+#define DFLL_OUTPUT_CFG_MAX_MASK	\
+		(OUT_MASK << DFLL_OUTPUT_CFG_MAX_SHIFT)
+#define DFLL_OUTPUT_CFG_MIN_SHIFT	8
+#define DFLL_OUTPUT_CFG_MIN_MASK	\
+		(OUT_MASK << DFLL_OUTPUT_CFG_MIN_SHIFT)
+#define DFLL_OUTPUT_CFG_PWM_DELTA	(0x1 << 7)
+#define DFLL_OUTPUT_CFG_PWM_ENABLE	(0x1 << 6)
+#define DFLL_OUTPUT_CFG_PWM_DIV_SHIFT	0
+#define DFLL_OUTPUT_CFG_PWM_DIV_MASK	\
+		(OUT_MASK << DFLL_OUTPUT_CFG_PWM_DIV_SHIFT)
+
+/* DFLL_OUTPUT_FORCE: closed loop mode voltage forcing control */
+#define DFLL_OUTPUT_FORCE		0x24
+#define DFLL_OUTPUT_FORCE_ENABLE	(0x1 << 6)
+#define DFLL_OUTPUT_FORCE_VALUE_SHIFT	0
+#define DFLL_OUTPUT_FORCE_VALUE_MASK	\
+		(OUT_MASK << DFLL_OUTPUT_FORCE_VALUE_SHIFT)
+
+/* DFLL_MONITOR_CTRL: internal monitor data source control */
+#define DFLL_MONITOR_CTRL		0x28
+#define DFLL_MONITOR_CTRL_FREQ		6
+
+/* DFLL_MONITOR_DATA: internal monitor data output */
+#define DFLL_MONITOR_DATA		0x2c
+#define DFLL_MONITOR_DATA_NEW_MASK	(0x1 << 16)
+#define DFLL_MONITOR_DATA_VAL_SHIFT	0
+#define DFLL_MONITOR_DATA_VAL_MASK	(0xFFFF << DFLL_MONITOR_DATA_VAL_SHIFT)
+
+/*
+ * I2C output control registers - access via dfll_i2c_{readl,writel}
+ */
+
+/* DFLL_I2C_CFG: I2C controller configuration register */
+#define DFLL_I2C_CFG			0x40
+#define DFLL_I2C_CFG_ARB_ENABLE		(0x1 << 20)
+#define DFLL_I2C_CFG_HS_CODE_SHIFT	16
+#define DFLL_I2C_CFG_HS_CODE_MASK	(0x7 << DFLL_I2C_CFG_HS_CODE_SHIFT)
+#define DFLL_I2C_CFG_PACKET_ENABLE	(0x1 << 15)
+#define DFLL_I2C_CFG_SIZE_SHIFT		12
+#define DFLL_I2C_CFG_SIZE_MASK		(0x7 << DFLL_I2C_CFG_SIZE_SHIFT)
+#define DFLL_I2C_CFG_SLAVE_ADDR_10	(0x1 << 10)
+#define DFLL_I2C_CFG_SLAVE_ADDR_SHIFT_7BIT	1
+#define DFLL_I2C_CFG_SLAVE_ADDR_SHIFT_10BIT	0
+
+/* DFLL_I2C_VDD_REG_ADDR: PMIC I2C address for closed loop mode */
+#define DFLL_I2C_VDD_REG_ADDR		0x44
+
+/* DFLL_I2C_STS: I2C controller status */
+#define DFLL_I2C_STS			0x48
+#define DFLL_I2C_STS_I2C_LAST_SHIFT	1
+#define DFLL_I2C_STS_I2C_REQ_PENDING	0x1
+
+/* DFLL_INTR_STS: DFLL interrupt status register */
+#define DFLL_INTR_STS			0x5c
+
+/* DFLL_INTR_EN: DFLL interrupt enable register */
+#define DFLL_INTR_EN			0x60
+#define DFLL_INTR_MIN_MASK		0x1
+#define DFLL_INTR_MAX_MASK		0x2
+
+/*
+ * Integrated I2C controller registers - relative to td->i2c_controller_base
+ */
+
+/* DFLL_I2C_CLK_DIVISOR: I2C controller clock divisor */
+#define DFLL_I2C_CLK_DIVISOR		0x6c
+#define DFLL_I2C_CLK_DIVISOR_MASK	0xffff
+#define DFLL_I2C_CLK_DIVISOR_FS_SHIFT	16
+#define DFLL_I2C_CLK_DIVISOR_HS_SHIFT	0
+#define DFLL_I2C_CLK_DIVISOR_PREDIV	8
+#define DFLL_I2C_CLK_DIVISOR_HSMODE_PREDIV	12
+
+/*
+ * Other constants
+ */
+
+/* MAX_DFLL_VOLTAGES: number of LUT entries in the DFLL IP block */
+#define MAX_DFLL_VOLTAGES		33
+
+/*
+ * REF_CLK_CYC_PER_DVCO_SAMPLE: the number of ref_clk cycles that the hardware
+ *    integrates the DVCO counter over - used for debug rate monitoring and
+ *    droop control
+ */
+#define REF_CLK_CYC_PER_DVCO_SAMPLE	4
+
+/*
+ * REF_CLOCK_RATE: the DFLL reference clock rate currently supported by this
+ * driver, in Hz
+ */
+#define REF_CLOCK_RATE			51000000UL
+
+#define DVCO_RATE_TO_MULT(rate, ref_rate)	((rate) / ((ref_rate) / 2))
+#define MULT_TO_DVCO_RATE(mult, ref_rate)	((mult) * ((ref_rate) / 2))
+
+/**
+ * enum dfll_ctrl_mode - DFLL hardware operating mode
+ * @DFLL_UNINITIALIZED: (uninitialized state - not in hardware bitfield)
+ * @DFLL_DISABLED: DFLL not generating an output clock
+ * @DFLL_OPEN_LOOP: DVCO running, but DFLL not adjusting voltage
+ * @DFLL_CLOSED_LOOP: DVCO running, and DFLL adjusting voltage to match
+ *		      the requested rate
+ *
+ * The integer corresponding to the last two states, minus one, is
+ * written to the DFLL hardware to change operating modes.
+ */
+enum dfll_ctrl_mode {
+	DFLL_UNINITIALIZED = 0,
+	DFLL_DISABLED = 1,
+	DFLL_OPEN_LOOP = 2,
+	DFLL_CLOSED_LOOP = 3,
+};
+
+/**
+ * enum dfll_tune_range - voltage range that the driver believes it's in
+ * @DFLL_TUNE_UNINITIALIZED: DFLL tuning not yet programmed
+ * @DFLL_TUNE_LOW: DFLL in the low-voltage range (or open-loop mode)
+ *
+ * Some DFLL tuning parameters may need to change depending on the
+ * DVCO's voltage; these states represent the ranges that the driver
+ * supports. These are software states; these values are never
+ * written into registers.
+ */
+enum dfll_tune_range {
+	DFLL_TUNE_UNINITIALIZED = 0,
+	DFLL_TUNE_LOW = 1,
+};
+
+
+enum tegra_dfll_pmu_if {
+	TEGRA_DFLL_PMU_I2C = 0,
+	TEGRA_DFLL_PMU_PWM = 1,
+};
+
+/**
+ * struct dfll_rate_req - target DFLL rate request data
+ * @rate: target frequency, after the postscaling
+ * @dvco_target_rate: target frequency, after the postscaling
+ * @lut_index: LUT index at which voltage the dvco_target_rate will be reached
+ * @mult_bits: value to program to the MULT bits of the DFLL_FREQ_REQ register
+ * @scale_bits: value to program to the SCALE bits of the DFLL_FREQ_REQ register
+ */
+struct dfll_rate_req {
+	unsigned long rate;
+	unsigned long dvco_target_rate;
+	int lut_index;
+	u8 mult_bits;
+	u8 scale_bits;
+};
+
+struct tegra_dfll {
+	struct device			*dev;
+	struct tegra_dfll_soc_data	*soc;
+
+	void __iomem			*base;
+	void __iomem			*i2c_base;
+	void __iomem			*i2c_controller_base;
+	void __iomem			*lut_base;
+
+	struct regulator		*vdd_reg;
+	struct clk			*soc_clk;
+	struct clk			*ref_clk;
+	struct clk			*i2c_clk;
+	struct clk			*dfll_clk;
+	struct reset_control		*dfll_rst;
+	struct reset_control		*dvco_rst;
+	unsigned long			ref_rate;
+	unsigned long			i2c_clk_rate;
+	unsigned long			dvco_rate_min;
+
+	enum dfll_ctrl_mode		mode;
+	enum dfll_tune_range		tune_range;
+	struct dentry			*debugfs_dir;
+	struct clk_hw			dfll_clk_hw;
+	const char			*output_clock_name;
+	struct dfll_rate_req		last_req;
+	unsigned long			last_unrounded_rate;
+
+	/* Parameters from DT */
+	u32				droop_ctrl;
+	u32				sample_rate;
+	u32				force_mode;
+	u32				cf;
+	u32				ci;
+	u32				cg;
+	bool				cg_scale;
+
+	/* I2C interface parameters */
+	u32				i2c_fs_rate;
+	u32				i2c_reg;
+	u32				i2c_slave_addr;
+
+	/* lut array entries are regulator framework selectors or PWM values*/
+	unsigned			lut[MAX_DFLL_VOLTAGES];
+	unsigned long			lut_uv[MAX_DFLL_VOLTAGES];
+	int				lut_size;
+	u8				lut_bottom, lut_min, lut_max, lut_safe;
+
+	/* PWM interface */
+	enum tegra_dfll_pmu_if		pmu_if;
+	unsigned long			pwm_rate;
+	struct pinctrl			*pwm_pin;
+	struct pinctrl_state		*pwm_enable_state;
+	struct pinctrl_state		*pwm_disable_state;
+	u32				reg_init_uV;
+};
+
+#define clk_hw_to_dfll(_hw) container_of(_hw, struct tegra_dfll, dfll_clk_hw)
+
+/* mode_name: map numeric DFLL modes to names for friendly console messages */
+static const char * const mode_name[] = {
+	[DFLL_UNINITIALIZED] = "uninitialized",
+	[DFLL_DISABLED] = "disabled",
+	[DFLL_OPEN_LOOP] = "open_loop",
+	[DFLL_CLOSED_LOOP] = "closed_loop",
+};
+
+/*
+ * Register accessors
+ */
+
+static inline u32 dfll_readl(struct tegra_dfll *td, u32 offs)
+{
+	return __raw_readl(td->base + offs);
+}
+
+static inline void dfll_writel(struct tegra_dfll *td, u32 val, u32 offs)
+{
+	WARN_ON(offs >= DFLL_I2C_CFG);
+	__raw_writel(val, td->base + offs);
+}
+
+static inline void dfll_wmb(struct tegra_dfll *td)
+{
+	dfll_readl(td, DFLL_CTRL);
+}
+
+/* I2C output control registers - for addresses above DFLL_I2C_CFG */
+
+static inline u32 dfll_i2c_readl(struct tegra_dfll *td, u32 offs)
+{
+	return __raw_readl(td->i2c_base + offs);
+}
+
+static inline void dfll_i2c_writel(struct tegra_dfll *td, u32 val, u32 offs)
+{
+	__raw_writel(val, td->i2c_base + offs);
+}
+
+static inline void dfll_i2c_wmb(struct tegra_dfll *td)
+{
+	dfll_i2c_readl(td, DFLL_I2C_CFG);
+}
+
+/**
+ * dfll_is_running - is the DFLL currently generating a clock?
+ * @td: DFLL instance
+ *
+ * If the DFLL is currently generating an output clock signal, return
+ * true; otherwise return false.
+ */
+static bool dfll_is_running(struct tegra_dfll *td)
+{
+	return td->mode >= DFLL_OPEN_LOOP;
+}
+
+/*
+ * Runtime PM suspend/resume callbacks
+ */
+
+/**
+ * tegra_dfll_runtime_resume - enable all clocks needed by the DFLL
+ * @dev: DFLL device *
+ *
+ * Enable all clocks needed by the DFLL. Assumes that clk_prepare()
+ * has already been called on all the clocks.
+ *
+ * XXX Should also handle context restore when returning from off.
+ */
+int tegra_dfll_runtime_resume(struct device *dev)
+{
+	struct tegra_dfll *td = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_enable(td->ref_clk);
+	if (ret) {
+		dev_err(dev, "could not enable ref clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_enable(td->soc_clk);
+	if (ret) {
+		dev_err(dev, "could not enable register clock: %d\n", ret);
+		clk_disable(td->ref_clk);
+		return ret;
+	}
+
+	ret = clk_enable(td->i2c_clk);
+	if (ret) {
+		dev_err(dev, "could not enable i2c clock: %d\n", ret);
+		clk_disable(td->soc_clk);
+		clk_disable(td->ref_clk);
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(tegra_dfll_runtime_resume);
+
+/**
+ * tegra_dfll_runtime_suspend - disable all clocks needed by the DFLL
+ * @dev: DFLL device *
+ *
+ * Disable all clocks needed by the DFLL. Assumes that other code
+ * will later call clk_unprepare().
+ */
+int tegra_dfll_runtime_suspend(struct device *dev)
+{
+	struct tegra_dfll *td = dev_get_drvdata(dev);
+
+	clk_disable(td->ref_clk);
+	clk_disable(td->soc_clk);
+	clk_disable(td->i2c_clk);
+
+	return 0;
+}
+EXPORT_SYMBOL(tegra_dfll_runtime_suspend);
+
+/*
+ * DFLL tuning operations (per-voltage-range tuning settings)
+ */
+
+/**
+ * dfll_tune_low - tune to DFLL and CPU settings valid for any voltage
+ * @td: DFLL instance
+ *
+ * Tune the DFLL oscillator parameters and the CPU clock shaper for
+ * the low-voltage range. These settings are valid for any voltage,
+ * but may not be optimal.
+ */
+static void dfll_tune_low(struct tegra_dfll *td)
+{
+	td->tune_range = DFLL_TUNE_LOW;
+
+	dfll_writel(td, td->soc->cvb->cpu_dfll_data.tune0_low, DFLL_TUNE0);
+	dfll_writel(td, td->soc->cvb->cpu_dfll_data.tune1, DFLL_TUNE1);
+	dfll_wmb(td);
+
+	if (td->soc->set_clock_trimmers_low)
+		td->soc->set_clock_trimmers_low();
+}
+
+/*
+ * Output clock scaler helpers
+ */
+
+/**
+ * dfll_scale_dvco_rate - calculate scaled rate from the DVCO rate
+ * @scale_bits: clock scaler value (bits in the DFLL_FREQ_REQ_SCALE field)
+ * @dvco_rate: the DVCO rate
+ *
+ * Apply the same scaling formula that the DFLL hardware uses to scale
+ * the DVCO rate.
+ */
+static unsigned long dfll_scale_dvco_rate(int scale_bits,
+					  unsigned long dvco_rate)
+{
+	return (u64)dvco_rate * (scale_bits + 1) / DFLL_FREQ_REQ_SCALE_MAX;
+}
+
+/*
+ * DFLL mode switching
+ */
+
+/**
+ * dfll_set_mode - change the DFLL control mode
+ * @td: DFLL instance
+ * @mode: DFLL control mode (see enum dfll_ctrl_mode)
+ *
+ * Change the DFLL's operating mode between disabled, open-loop mode,
+ * and closed-loop mode, or vice versa.
+ */
+static void dfll_set_mode(struct tegra_dfll *td,
+			  enum dfll_ctrl_mode mode)
+{
+	td->mode = mode;
+	dfll_writel(td, mode - 1, DFLL_CTRL);
+	dfll_wmb(td);
+}
+
+/*
+ * DVCO rate control
+ */
+
+static unsigned long get_dvco_rate_below(struct tegra_dfll *td, u8 out_min)
+{
+	struct dev_pm_opp *opp;
+	unsigned long rate, prev_rate;
+	unsigned long uv, min_uv;
+
+	min_uv = td->lut_uv[out_min];
+	for (rate = 0, prev_rate = 0; ; rate++) {
+		opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
+		if (IS_ERR(opp))
+			break;
+
+		uv = dev_pm_opp_get_voltage(opp);
+		dev_pm_opp_put(opp);
+
+		if (uv && uv > min_uv)
+			return prev_rate;
+
+		prev_rate = rate;
+	}
+
+	return prev_rate;
+}
+
+/*
+ * DFLL-to-I2C controller interface
+ */
+
+/**
+ * dfll_i2c_set_output_enabled - enable/disable I2C PMIC voltage requests
+ * @td: DFLL instance
+ * @enable: whether to enable or disable the I2C voltage requests
+ *
+ * Set the master enable control for I2C control value updates. If disabled,
+ * then I2C control messages are inhibited, regardless of the DFLL mode.
+ */
+static int dfll_i2c_set_output_enabled(struct tegra_dfll *td, bool enable)
+{
+	u32 val;
+
+	val = dfll_i2c_readl(td, DFLL_OUTPUT_CFG);
+
+	if (enable)
+		val |= DFLL_OUTPUT_CFG_I2C_ENABLE;
+	else
+		val &= ~DFLL_OUTPUT_CFG_I2C_ENABLE;
+
+	dfll_i2c_writel(td, val, DFLL_OUTPUT_CFG);
+	dfll_i2c_wmb(td);
+
+	return 0;
+}
+
+
+/*
+ * DFLL-to-PWM controller interface
+ */
+
+/**
+ * dfll_pwm_set_output_enabled - enable/disable PWM voltage requests
+ * @td: DFLL instance
+ * @enable: whether to enable or disable the PWM voltage requests
+ *
+ * Set the master enable control for PWM control value updates. If disabled,
+ * then the PWM signal is not driven. Also configure the PWM output pad
+ * to the appropriate state.
+ */
+static int dfll_pwm_set_output_enabled(struct tegra_dfll *td, bool enable)
+{
+	int ret;
+	u32 val, div;
+
+	if (enable) {
+		ret = pinctrl_select_state(td->pwm_pin, td->pwm_enable_state);
+		if (ret < 0) {
+			dev_err(td->dev, "setting enable state failed\n");
+			return -EINVAL;
+		}
+		val = dfll_readl(td, DFLL_OUTPUT_CFG);
+		val &= ~DFLL_OUTPUT_CFG_PWM_DIV_MASK;
+		div = DIV_ROUND_UP(td->ref_rate, td->pwm_rate);
+		val |= (div << DFLL_OUTPUT_CFG_PWM_DIV_SHIFT)
+				& DFLL_OUTPUT_CFG_PWM_DIV_MASK;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+
+		val |= DFLL_OUTPUT_CFG_PWM_ENABLE;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+	} else {
+		ret = pinctrl_select_state(td->pwm_pin, td->pwm_disable_state);
+		if (ret < 0)
+			dev_warn(td->dev, "setting disable state failed\n");
+
+		val = dfll_readl(td, DFLL_OUTPUT_CFG);
+		val &= ~DFLL_OUTPUT_CFG_PWM_ENABLE;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+	}
+
+	return 0;
+}
+
+/**
+ * dfll_set_force_output_value - set fixed value for force output
+ * @td: DFLL instance
+ * @out_val: value to force output
+ *
+ * Set the fixed value for force output, DFLL will output this value when
+ * force output is enabled.
+ */
+static u32 dfll_set_force_output_value(struct tegra_dfll *td, u8 out_val)
+{
+	u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE);
+
+	val = (val & DFLL_OUTPUT_FORCE_ENABLE) | (out_val & OUT_MASK);
+	dfll_writel(td, val, DFLL_OUTPUT_FORCE);
+	dfll_wmb(td);
+
+	return dfll_readl(td, DFLL_OUTPUT_FORCE);
+}
+
+/**
+ * dfll_set_force_output_enabled - enable/disable force output
+ * @td: DFLL instance
+ * @enable: whether to enable or disable the force output
+ *
+ * Set the enable control for fouce output with fixed value.
+ */
+static void dfll_set_force_output_enabled(struct tegra_dfll *td, bool enable)
+{
+	u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE);
+
+	if (enable)
+		val |= DFLL_OUTPUT_FORCE_ENABLE;
+	else
+		val &= ~DFLL_OUTPUT_FORCE_ENABLE;
+
+	dfll_writel(td, val, DFLL_OUTPUT_FORCE);
+	dfll_wmb(td);
+}
+
+/**
+ * dfll_force_output - force output a fixed value
+ * @td: DFLL instance
+ * @out_sel: value to force output
+ *
+ * Set the fixed value for force output, DFLL will output this value.
+ */
+static int dfll_force_output(struct tegra_dfll *td, unsigned int out_sel)
+{
+	u32 val;
+
+	if (out_sel > OUT_MASK)
+		return -EINVAL;
+
+	val = dfll_set_force_output_value(td, out_sel);
+	if ((td->mode < DFLL_CLOSED_LOOP) &&
+	    !(val & DFLL_OUTPUT_FORCE_ENABLE)) {
+		dfll_set_force_output_enabled(td, true);
+	}
+
+	return 0;
+}
+
+/**
+ * dfll_load_i2c_lut - load the voltage lookup table
+ * @td: struct tegra_dfll *
+ *
+ * Load the voltage-to-PMIC register value lookup table into the DFLL
+ * IP block memory. Look-up tables can be loaded at any time.
+ */
+static void dfll_load_i2c_lut(struct tegra_dfll *td)
+{
+	int i, lut_index;
+	u32 val;
+
+	for (i = 0; i < MAX_DFLL_VOLTAGES; i++) {
+		if (i < td->lut_min)
+			lut_index = td->lut_min;
+		else if (i > td->lut_max)
+			lut_index = td->lut_max;
+		else
+			lut_index = i;
+
+		val = regulator_list_hardware_vsel(td->vdd_reg,
+						     td->lut[lut_index]);
+		__raw_writel(val, td->lut_base + i * 4);
+	}
+
+	dfll_i2c_wmb(td);
+}
+
+/**
+ * dfll_init_i2c_if - set up the DFLL's DFLL-I2C interface
+ * @td: DFLL instance
+ *
+ * During DFLL driver initialization, program the DFLL-I2C interface
+ * with the PMU slave address, vdd register offset, and transfer mode.
+ * This data is used by the DFLL to automatically construct I2C
+ * voltage-set commands, which are then passed to the DFLL's internal
+ * I2C controller.
+ */
+static void dfll_init_i2c_if(struct tegra_dfll *td)
+{
+	u32 val;
+
+	if (td->i2c_slave_addr > 0x7f) {
+		val = td->i2c_slave_addr << DFLL_I2C_CFG_SLAVE_ADDR_SHIFT_10BIT;
+		val |= DFLL_I2C_CFG_SLAVE_ADDR_10;
+	} else {
+		val = td->i2c_slave_addr << DFLL_I2C_CFG_SLAVE_ADDR_SHIFT_7BIT;
+	}
+	val |= DFLL_I2C_CFG_SIZE_MASK;
+	val |= DFLL_I2C_CFG_ARB_ENABLE;
+	dfll_i2c_writel(td, val, DFLL_I2C_CFG);
+
+	dfll_i2c_writel(td, td->i2c_reg, DFLL_I2C_VDD_REG_ADDR);
+
+	val = DIV_ROUND_UP(td->i2c_clk_rate, td->i2c_fs_rate * 8);
+	BUG_ON(!val || (val > DFLL_I2C_CLK_DIVISOR_MASK));
+	val = (val - 1) << DFLL_I2C_CLK_DIVISOR_FS_SHIFT;
+
+	/* default hs divisor just in case */
+	val |= 1 << DFLL_I2C_CLK_DIVISOR_HS_SHIFT;
+	__raw_writel(val, td->i2c_controller_base + DFLL_I2C_CLK_DIVISOR);
+	dfll_i2c_wmb(td);
+}
+
+/**
+ * dfll_init_out_if - prepare DFLL-to-PMIC interface
+ * @td: DFLL instance
+ *
+ * During DFLL driver initialization or resume from context loss,
+ * disable the I2C command output to the PMIC, set safe voltage and
+ * output limits, and disable and clear limit interrupts.
+ */
+static void dfll_init_out_if(struct tegra_dfll *td)
+{
+	u32 val;
+
+	td->lut_min = td->lut_bottom;
+	td->lut_max = td->lut_size - 1;
+	td->lut_safe = td->lut_min + (td->lut_min < td->lut_max ? 1 : 0);
+
+	/* clear DFLL_OUTPUT_CFG before setting new value */
+	dfll_writel(td, 0, DFLL_OUTPUT_CFG);
+	dfll_wmb(td);
+
+	val = (td->lut_safe << DFLL_OUTPUT_CFG_SAFE_SHIFT) |
+	      (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) |
+	      (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT);
+	dfll_writel(td, val, DFLL_OUTPUT_CFG);
+	dfll_wmb(td);
+
+	dfll_writel(td, 0, DFLL_OUTPUT_FORCE);
+	dfll_i2c_writel(td, 0, DFLL_INTR_EN);
+	dfll_i2c_writel(td, DFLL_INTR_MAX_MASK | DFLL_INTR_MIN_MASK,
+			DFLL_INTR_STS);
+
+	if (td->pmu_if == TEGRA_DFLL_PMU_PWM) {
+		u32 vinit = td->reg_init_uV;
+		int vstep = td->soc->alignment.step_uv;
+		unsigned long vmin = td->lut_uv[0];
+
+		/* set initial voltage */
+		if ((vinit >= vmin) && vstep) {
+			unsigned int vsel;
+
+			vsel = DIV_ROUND_UP((vinit - vmin), vstep);
+			dfll_force_output(td, vsel);
+		}
+	} else {
+		dfll_load_i2c_lut(td);
+		dfll_init_i2c_if(td);
+	}
+}
+
+/*
+ * Set/get the DFLL's targeted output clock rate
+ */
+
+/**
+ * find_lut_index_for_rate - determine I2C LUT index for given DFLL rate
+ * @td: DFLL instance
+ * @rate: clock rate
+ *
+ * Determines the index of a I2C LUT entry for a voltage that approximately
+ * produces the given DFLL clock rate. This is used when forcing a value
+ * to the integrator during rate changes. Returns -ENOENT if a suitable
+ * LUT index is not found.
+ */
+static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate)
+{
+	struct dev_pm_opp *opp;
+	int i, align_step;
+
+	opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
+	if (IS_ERR(opp))
+		return PTR_ERR(opp);
+
+	align_step = dev_pm_opp_get_voltage(opp) / td->soc->alignment.step_uv;
+	dev_pm_opp_put(opp);
+
+	for (i = td->lut_bottom; i < td->lut_size; i++) {
+		if ((td->lut_uv[i] / td->soc->alignment.step_uv) >= align_step)
+			return i;
+	}
+
+	return -ENOENT;
+}
+
+/**
+ * dfll_calculate_rate_request - calculate DFLL parameters for a given rate
+ * @td: DFLL instance
+ * @req: DFLL-rate-request structure
+ * @rate: the desired DFLL rate
+ *
+ * Populate the DFLL-rate-request record @req fields with the scale_bits
+ * and mult_bits fields, based on the target input rate. Returns 0 upon
+ * success, or -EINVAL if the requested rate in req->rate is too high
+ * or low for the DFLL to generate.
+ */
+static int dfll_calculate_rate_request(struct tegra_dfll *td,
+				       struct dfll_rate_req *req,
+				       unsigned long rate)
+{
+	u32 val;
+
+	/*
+	 * If requested rate is below the minimum DVCO rate, active the scaler.
+	 * In the future the DVCO minimum voltage should be selected based on
+	 * chip temperature and the actual minimum rate should be calibrated
+	 * at runtime.
+	 */
+	req->scale_bits = DFLL_FREQ_REQ_SCALE_MAX - 1;
+	if (rate < td->dvco_rate_min) {
+		int scale;
+
+		scale = DIV_ROUND_CLOSEST(rate / 1000 * DFLL_FREQ_REQ_SCALE_MAX,
+					  td->dvco_rate_min / 1000);
+		if (!scale) {
+			dev_err(td->dev, "%s: Rate %lu is too low\n",
+				__func__, rate);
+			return -EINVAL;
+		}
+		req->scale_bits = scale - 1;
+		rate = td->dvco_rate_min;
+	}
+
+	/* Convert requested rate into frequency request and scale settings */
+	val = DVCO_RATE_TO_MULT(rate, td->ref_rate);
+	if (val > FREQ_MAX) {
+		dev_err(td->dev, "%s: Rate %lu is above dfll range\n",
+			__func__, rate);
+		return -EINVAL;
+	}
+	req->mult_bits = val;
+	req->dvco_target_rate = MULT_TO_DVCO_RATE(req->mult_bits, td->ref_rate);
+	req->rate = dfll_scale_dvco_rate(req->scale_bits,
+					 req->dvco_target_rate);
+	req->lut_index = find_lut_index_for_rate(td, req->dvco_target_rate);
+	if (req->lut_index < 0)
+		return req->lut_index;
+
+	return 0;
+}
+
+/**
+ * dfll_set_frequency_request - start the frequency change operation
+ * @td: DFLL instance
+ * @req: rate request structure
+ *
+ * Tell the DFLL to try to change its output frequency to the
+ * frequency represented by @req. DFLL must be in closed-loop mode.
+ */
+static void dfll_set_frequency_request(struct tegra_dfll *td,
+				       struct dfll_rate_req *req)
+{
+	u32 val = 0;
+	int force_val;
+	int coef = 128; /* FIXME: td->cg_scale? */;
+
+	force_val = (req->lut_index - td->lut_safe) * coef / td->cg;
+	force_val = clamp(force_val, FORCE_MIN, FORCE_MAX);
+
+	val |= req->mult_bits << DFLL_FREQ_REQ_MULT_SHIFT;
+	val |= req->scale_bits << DFLL_FREQ_REQ_SCALE_SHIFT;
+	val |= ((u32)force_val << DFLL_FREQ_REQ_FORCE_SHIFT) &
+		DFLL_FREQ_REQ_FORCE_MASK;
+	val |= DFLL_FREQ_REQ_FREQ_VALID | DFLL_FREQ_REQ_FORCE_ENABLE;
+
+	dfll_writel(td, val, DFLL_FREQ_REQ);
+	dfll_wmb(td);
+}
+
+/**
+ * dfll_request_rate - set the next rate for the DFLL to tune to
+ * @td: DFLL instance
+ * @rate: clock rate to target
+ *
+ * Convert the requested clock rate @rate into the DFLL control logic
+ * settings. In closed-loop mode, update new settings immediately to
+ * adjust DFLL output rate accordingly. Otherwise, just save them
+ * until the next switch to closed loop. Returns 0 upon success,
+ * -EPERM if the DFLL driver has not yet been initialized, or -EINVAL
+ * if @rate is outside the DFLL's tunable range.
+ */
+static int dfll_request_rate(struct tegra_dfll *td, unsigned long rate)
+{
+	int ret;
+	struct dfll_rate_req req;
+
+	if (td->mode == DFLL_UNINITIALIZED) {
+		dev_err(td->dev, "%s: Cannot set DFLL rate in %s mode\n",
+			__func__, mode_name[td->mode]);
+		return -EPERM;
+	}
+
+	ret = dfll_calculate_rate_request(td, &req, rate);
+	if (ret)
+		return ret;
+
+	td->last_unrounded_rate = rate;
+	td->last_req = req;
+
+	if (td->mode == DFLL_CLOSED_LOOP)
+		dfll_set_frequency_request(td, &td->last_req);
+
+	return 0;
+}
+
+/*
+ * DFLL enable/disable & open-loop <-> closed-loop transitions
+ */
+
+/**
+ * dfll_disable - switch from open-loop mode to disabled mode
+ * @td: DFLL instance
+ *
+ * Switch from OPEN_LOOP state to DISABLED state. Returns 0 upon success
+ * or -EPERM if the DFLL is not currently in open-loop mode.
+ */
+static int dfll_disable(struct tegra_dfll *td)
+{
+	if (td->mode != DFLL_OPEN_LOOP) {
+		dev_err(td->dev, "cannot disable DFLL in %s mode\n",
+			mode_name[td->mode]);
+		return -EINVAL;
+	}
+
+	dfll_set_mode(td, DFLL_DISABLED);
+	pm_runtime_put_sync(td->dev);
+
+	return 0;
+}
+
+/**
+ * dfll_enable - switch a disabled DFLL to open-loop mode
+ * @td: DFLL instance
+ *
+ * Switch from DISABLED state to OPEN_LOOP state. Returns 0 upon success
+ * or -EPERM if the DFLL is not currently disabled.
+ */
+static int dfll_enable(struct tegra_dfll *td)
+{
+	if (td->mode != DFLL_DISABLED) {
+		dev_err(td->dev, "cannot enable DFLL in %s mode\n",
+			mode_name[td->mode]);
+		return -EPERM;
+	}
+
+	pm_runtime_get_sync(td->dev);
+	dfll_set_mode(td, DFLL_OPEN_LOOP);
+
+	return 0;
+}
+
+/**
+ * dfll_set_open_loop_config - prepare to switch to open-loop mode
+ * @td: DFLL instance
+ *
+ * Prepare to switch the DFLL to open-loop mode. This switches the
+ * DFLL to the low-voltage tuning range, ensures that I2C output
+ * forcing is disabled, and disables the output clock rate scaler.
+ * The DFLL's low-voltage tuning range parameters must be
+ * characterized to keep the downstream device stable at any DVCO
+ * input voltage. No return value.
+ */
+static void dfll_set_open_loop_config(struct tegra_dfll *td)
+{
+	u32 val;
+
+	/* always tune low (safe) in open loop */
+	if (td->tune_range != DFLL_TUNE_LOW)
+		dfll_tune_low(td);
+
+	val = dfll_readl(td, DFLL_FREQ_REQ);
+	val |= DFLL_FREQ_REQ_SCALE_MASK;
+	val &= ~DFLL_FREQ_REQ_FORCE_ENABLE;
+	dfll_writel(td, val, DFLL_FREQ_REQ);
+	dfll_wmb(td);
+}
+
+/**
+ * dfll_lock - switch from open-loop to closed-loop mode
+ * @td: DFLL instance
+ *
+ * Switch from OPEN_LOOP state to CLOSED_LOOP state. Returns 0 upon success,
+ * -EINVAL if the DFLL's target rate hasn't been set yet, or -EPERM if the
+ * DFLL is not currently in open-loop mode.
+ */
+static int dfll_lock(struct tegra_dfll *td)
+{
+	struct dfll_rate_req *req = &td->last_req;
+
+	switch (td->mode) {
+	case DFLL_CLOSED_LOOP:
+		return 0;
+
+	case DFLL_OPEN_LOOP:
+		if (req->rate == 0) {
+			dev_err(td->dev, "%s: Cannot lock DFLL at rate 0\n",
+				__func__);
+			return -EINVAL;
+		}
+
+		if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+			dfll_pwm_set_output_enabled(td, true);
+		else
+			dfll_i2c_set_output_enabled(td, true);
+
+		dfll_set_mode(td, DFLL_CLOSED_LOOP);
+		dfll_set_frequency_request(td, req);
+		dfll_set_force_output_enabled(td, false);
+		return 0;
+
+	default:
+		BUG_ON(td->mode > DFLL_CLOSED_LOOP);
+		dev_err(td->dev, "%s: Cannot lock DFLL in %s mode\n",
+			__func__, mode_name[td->mode]);
+		return -EPERM;
+	}
+}
+
+/**
+ * dfll_unlock - switch from closed-loop to open-loop mode
+ * @td: DFLL instance
+ *
+ * Switch from CLOSED_LOOP state to OPEN_LOOP state. Returns 0 upon success,
+ * or -EPERM if the DFLL is not currently in open-loop mode.
+ */
+static int dfll_unlock(struct tegra_dfll *td)
+{
+	switch (td->mode) {
+	case DFLL_CLOSED_LOOP:
+		dfll_set_open_loop_config(td);
+		dfll_set_mode(td, DFLL_OPEN_LOOP);
+		if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+			dfll_pwm_set_output_enabled(td, false);
+		else
+			dfll_i2c_set_output_enabled(td, false);
+		return 0;
+
+	case DFLL_OPEN_LOOP:
+		return 0;
+
+	default:
+		BUG_ON(td->mode > DFLL_CLOSED_LOOP);
+		dev_err(td->dev, "%s: Cannot unlock DFLL in %s mode\n",
+			__func__, mode_name[td->mode]);
+		return -EPERM;
+	}
+}
+
+/*
+ * Clock framework integration
+ *
+ * When the DFLL is being controlled by the CCF, always enter closed loop
+ * mode when the clk is enabled. This requires that a DFLL rate request
+ * has been set beforehand, which implies that a clk_set_rate() call is
+ * always required before a clk_enable().
+ */
+
+static int dfll_clk_is_enabled(struct clk_hw *hw)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+
+	return dfll_is_running(td);
+}
+
+static int dfll_clk_enable(struct clk_hw *hw)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+	int ret;
+
+	ret = dfll_enable(td);
+	if (ret)
+		return ret;
+
+	ret = dfll_lock(td);
+	if (ret)
+		dfll_disable(td);
+
+	return ret;
+}
+
+static void dfll_clk_disable(struct clk_hw *hw)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+	int ret;
+
+	ret = dfll_unlock(td);
+	if (!ret)
+		dfll_disable(td);
+}
+
+static unsigned long dfll_clk_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+
+	return td->last_unrounded_rate;
+}
+
+/* Must use determine_rate since it allows for rates exceeding 2^31-1 */
+static int dfll_clk_determine_rate(struct clk_hw *hw,
+				   struct clk_rate_request *clk_req)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+	struct dfll_rate_req req;
+	int ret;
+
+	ret = dfll_calculate_rate_request(td, &req, clk_req->rate);
+	if (ret)
+		return ret;
+
+	/*
+	 * Don't set the rounded rate, since it doesn't really matter as
+	 * the output rate will be voltage controlled anyway, and cpufreq
+	 * freaks out if any rounding happens.
+	 */
+
+	return 0;
+}
+
+static int dfll_clk_set_rate(struct clk_hw *hw, unsigned long rate,
+			     unsigned long parent_rate)
+{
+	struct tegra_dfll *td = clk_hw_to_dfll(hw);
+
+	return dfll_request_rate(td, rate);
+}
+
+static const struct clk_ops dfll_clk_ops = {
+	.is_enabled	= dfll_clk_is_enabled,
+	.enable		= dfll_clk_enable,
+	.disable	= dfll_clk_disable,
+	.recalc_rate	= dfll_clk_recalc_rate,
+	.determine_rate	= dfll_clk_determine_rate,
+	.set_rate	= dfll_clk_set_rate,
+};
+
+static struct clk_init_data dfll_clk_init_data = {
+	.ops		= &dfll_clk_ops,
+	.num_parents	= 0,
+};
+
+/**
+ * dfll_register_clk - register the DFLL output clock with the clock framework
+ * @td: DFLL instance
+ *
+ * Register the DFLL's output clock with the Linux clock framework and register
+ * the DFLL driver as an OF clock provider. Returns 0 upon success or -EINVAL
+ * or -ENOMEM upon failure.
+ */
+static int dfll_register_clk(struct tegra_dfll *td)
+{
+	int ret;
+
+	dfll_clk_init_data.name = td->output_clock_name;
+	td->dfll_clk_hw.init = &dfll_clk_init_data;
+
+	td->dfll_clk = clk_register(td->dev, &td->dfll_clk_hw);
+	if (IS_ERR(td->dfll_clk)) {
+		dev_err(td->dev, "DFLL clock registration error\n");
+		return -EINVAL;
+	}
+
+	ret = of_clk_add_provider(td->dev->of_node, of_clk_src_simple_get,
+				  td->dfll_clk);
+	if (ret) {
+		dev_err(td->dev, "of_clk_add_provider() failed\n");
+
+		clk_unregister(td->dfll_clk);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * dfll_unregister_clk - unregister the DFLL output clock
+ * @td: DFLL instance
+ *
+ * Unregister the DFLL's output clock from the Linux clock framework
+ * and from clkdev. No return value.
+ */
+static void dfll_unregister_clk(struct tegra_dfll *td)
+{
+	of_clk_del_provider(td->dev->of_node);
+	clk_unregister(td->dfll_clk);
+	td->dfll_clk = NULL;
+}
+
+/*
+ * Debugfs interface
+ */
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * Monitor control
+ */
+
+/**
+ * dfll_calc_monitored_rate - convert DFLL_MONITOR_DATA_VAL rate into real freq
+ * @monitor_data: value read from the DFLL_MONITOR_DATA_VAL bitfield
+ * @ref_rate: DFLL reference clock rate
+ *
+ * Convert @monitor_data from DFLL_MONITOR_DATA_VAL units into cycles
+ * per second. Returns the converted value.
+ */
+static u64 dfll_calc_monitored_rate(u32 monitor_data,
+				    unsigned long ref_rate)
+{
+	return monitor_data * (ref_rate / REF_CLK_CYC_PER_DVCO_SAMPLE);
+}
+
+/**
+ * dfll_read_monitor_rate - return the DFLL's output rate from internal monitor
+ * @td: DFLL instance
+ *
+ * If the DFLL is enabled, return the last rate reported by the DFLL's
+ * internal monitoring hardware. This works in both open-loop and
+ * closed-loop mode, and takes the output scaler setting into account.
+ * Assumes that the monitor was programmed to monitor frequency before
+ * the sample period started. If the driver believes that the DFLL is
+ * currently uninitialized or disabled, it will return 0, since
+ * otherwise the DFLL monitor data register will return the last
+ * measured rate from when the DFLL was active.
+ */
+static u64 dfll_read_monitor_rate(struct tegra_dfll *td)
+{
+	u32 v, s;
+	u64 pre_scaler_rate, post_scaler_rate;
+
+	if (!dfll_is_running(td))
+		return 0;
+
+	v = dfll_readl(td, DFLL_MONITOR_DATA);
+	v = (v & DFLL_MONITOR_DATA_VAL_MASK) >> DFLL_MONITOR_DATA_VAL_SHIFT;
+	pre_scaler_rate = dfll_calc_monitored_rate(v, td->ref_rate);
+
+	s = dfll_readl(td, DFLL_FREQ_REQ);
+	s = (s & DFLL_FREQ_REQ_SCALE_MASK) >> DFLL_FREQ_REQ_SCALE_SHIFT;
+	post_scaler_rate = dfll_scale_dvco_rate(s, pre_scaler_rate);
+
+	return post_scaler_rate;
+}
+
+static int attr_enable_get(void *data, u64 *val)
+{
+	struct tegra_dfll *td = data;
+
+	*val = dfll_is_running(td);
+
+	return 0;
+}
+static int attr_enable_set(void *data, u64 val)
+{
+	struct tegra_dfll *td = data;
+
+	return val ? dfll_enable(td) : dfll_disable(td);
+}
+DEFINE_DEBUGFS_ATTRIBUTE(enable_fops, attr_enable_get, attr_enable_set,
+			 "%llu\n");
+
+static int attr_lock_get(void *data, u64 *val)
+{
+	struct tegra_dfll *td = data;
+
+	*val = (td->mode == DFLL_CLOSED_LOOP);
+
+	return 0;
+}
+static int attr_lock_set(void *data, u64 val)
+{
+	struct tegra_dfll *td = data;
+
+	return val ? dfll_lock(td) :  dfll_unlock(td);
+}
+DEFINE_DEBUGFS_ATTRIBUTE(lock_fops, attr_lock_get, attr_lock_set, "%llu\n");
+
+static int attr_rate_get(void *data, u64 *val)
+{
+	struct tegra_dfll *td = data;
+
+	*val = dfll_read_monitor_rate(td);
+
+	return 0;
+}
+
+static int attr_rate_set(void *data, u64 val)
+{
+	struct tegra_dfll *td = data;
+
+	return dfll_request_rate(td, val);
+}
+DEFINE_DEBUGFS_ATTRIBUTE(rate_fops, attr_rate_get, attr_rate_set, "%llu\n");
+
+static int attr_registers_show(struct seq_file *s, void *data)
+{
+	u32 val, offs;
+	struct tegra_dfll *td = s->private;
+
+	seq_puts(s, "CONTROL REGISTERS:\n");
+	for (offs = 0; offs <= DFLL_MONITOR_DATA; offs += 4) {
+		if (offs == DFLL_OUTPUT_CFG)
+			val = dfll_i2c_readl(td, offs);
+		else
+			val = dfll_readl(td, offs);
+		seq_printf(s, "[0x%02x] = 0x%08x\n", offs, val);
+	}
+
+	seq_puts(s, "\nI2C and INTR REGISTERS:\n");
+	for (offs = DFLL_I2C_CFG; offs <= DFLL_I2C_STS; offs += 4)
+		seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
+			   dfll_i2c_readl(td, offs));
+	for (offs = DFLL_INTR_STS; offs <= DFLL_INTR_EN; offs += 4)
+		seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
+			   dfll_i2c_readl(td, offs));
+
+	if (td->pmu_if == TEGRA_DFLL_PMU_I2C) {
+		seq_puts(s, "\nINTEGRATED I2C CONTROLLER REGISTERS:\n");
+		offs = DFLL_I2C_CLK_DIVISOR;
+		seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
+			   __raw_readl(td->i2c_controller_base + offs));
+
+		seq_puts(s, "\nLUT:\n");
+		for (offs = 0; offs <  4 * MAX_DFLL_VOLTAGES; offs += 4)
+			seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
+				   __raw_readl(td->lut_base + offs));
+	}
+
+	return 0;
+}
+
+DEFINE_SHOW_ATTRIBUTE(attr_registers);
+
+static void dfll_debug_init(struct tegra_dfll *td)
+{
+	struct dentry *root;
+
+	if (!td || (td->mode == DFLL_UNINITIALIZED))
+		return;
+
+	root = debugfs_create_dir("tegra_dfll_fcpu", NULL);
+	td->debugfs_dir = root;
+
+	debugfs_create_file_unsafe("enable", 0644, root, td,
+				   &enable_fops);
+	debugfs_create_file_unsafe("lock", 0444, root, td, &lock_fops);
+	debugfs_create_file_unsafe("rate", 0444, root, td, &rate_fops);
+	debugfs_create_file("registers", 0444, root, td, &attr_registers_fops);
+}
+
+#else
+static inline void dfll_debug_init(struct tegra_dfll *td) { }
+#endif /* CONFIG_DEBUG_FS */
+
+/*
+ * DFLL initialization
+ */
+
+/**
+ * dfll_set_default_params - program non-output related DFLL parameters
+ * @td: DFLL instance
+ *
+ * During DFLL driver initialization or resume from context loss,
+ * program parameters for the closed loop integrator, DVCO tuning,
+ * voltage droop control and monitor control.
+ */
+static void dfll_set_default_params(struct tegra_dfll *td)
+{
+	u32 val;
+
+	val = DIV_ROUND_UP(td->ref_rate, td->sample_rate * 32);
+	BUG_ON(val > DFLL_CONFIG_DIV_MASK);
+	dfll_writel(td, val, DFLL_CONFIG);
+
+	val = (td->force_mode << DFLL_PARAMS_FORCE_MODE_SHIFT) |
+		(td->cf << DFLL_PARAMS_CF_PARAM_SHIFT) |
+		(td->ci << DFLL_PARAMS_CI_PARAM_SHIFT) |
+		(td->cg << DFLL_PARAMS_CG_PARAM_SHIFT) |
+		(td->cg_scale ? DFLL_PARAMS_CG_SCALE : 0);
+	dfll_writel(td, val, DFLL_PARAMS);
+
+	dfll_tune_low(td);
+	dfll_writel(td, td->droop_ctrl, DFLL_DROOP_CTRL);
+	dfll_writel(td, DFLL_MONITOR_CTRL_FREQ, DFLL_MONITOR_CTRL);
+}
+
+/**
+ * dfll_init_clks - clk_get() the DFLL source clocks
+ * @td: DFLL instance
+ *
+ * Call clk_get() on the DFLL source clocks and save the pointers for later
+ * use. Returns 0 upon success or error (see devm_clk_get) if one or more
+ * of the clocks couldn't be looked up.
+ */
+static int dfll_init_clks(struct tegra_dfll *td)
+{
+	td->ref_clk = devm_clk_get(td->dev, "ref");
+	if (IS_ERR(td->ref_clk)) {
+		dev_err(td->dev, "missing ref clock\n");
+		return PTR_ERR(td->ref_clk);
+	}
+
+	td->soc_clk = devm_clk_get(td->dev, "soc");
+	if (IS_ERR(td->soc_clk)) {
+		dev_err(td->dev, "missing soc clock\n");
+		return PTR_ERR(td->soc_clk);
+	}
+
+	td->i2c_clk = devm_clk_get(td->dev, "i2c");
+	if (IS_ERR(td->i2c_clk)) {
+		dev_err(td->dev, "missing i2c clock\n");
+		return PTR_ERR(td->i2c_clk);
+	}
+	td->i2c_clk_rate = clk_get_rate(td->i2c_clk);
+
+	return 0;
+}
+
+/**
+ * dfll_init - Prepare the DFLL IP block for use
+ * @td: DFLL instance
+ *
+ * Do everything necessary to prepare the DFLL IP block for use. The
+ * DFLL will be left in DISABLED state. Called by dfll_probe().
+ * Returns 0 upon success, or passes along the error from whatever
+ * function returned it.
+ */
+static int dfll_init(struct tegra_dfll *td)
+{
+	int ret;
+
+	td->ref_rate = clk_get_rate(td->ref_clk);
+	if (td->ref_rate != REF_CLOCK_RATE) {
+		dev_err(td->dev, "unexpected ref clk rate %lu, expecting %lu",
+			td->ref_rate, REF_CLOCK_RATE);
+		return -EINVAL;
+	}
+
+	reset_control_deassert(td->dfll_rst);
+	reset_control_deassert(td->dvco_rst);
+
+	ret = clk_prepare(td->ref_clk);
+	if (ret) {
+		dev_err(td->dev, "failed to prepare ref_clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare(td->soc_clk);
+	if (ret) {
+		dev_err(td->dev, "failed to prepare soc_clk\n");
+		goto di_err1;
+	}
+
+	ret = clk_prepare(td->i2c_clk);
+	if (ret) {
+		dev_err(td->dev, "failed to prepare i2c_clk\n");
+		goto di_err2;
+	}
+
+	td->last_unrounded_rate = 0;
+
+	pm_runtime_enable(td->dev);
+	pm_runtime_get_sync(td->dev);
+
+	dfll_set_mode(td, DFLL_DISABLED);
+	dfll_set_default_params(td);
+
+	if (td->soc->init_clock_trimmers)
+		td->soc->init_clock_trimmers();
+
+	dfll_set_open_loop_config(td);
+
+	dfll_init_out_if(td);
+
+	pm_runtime_put_sync(td->dev);
+
+	return 0;
+
+di_err2:
+	clk_unprepare(td->soc_clk);
+di_err1:
+	clk_unprepare(td->ref_clk);
+
+	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
+
+	return ret;
+}
+
+/**
+ * tegra_dfll_suspend - check DFLL is disabled
+ * @dev: DFLL instance
+ *
+ * DFLL clock should be disabled by the CPUFreq driver. So, make
+ * sure it is disabled and disable all clocks needed by the DFLL.
+ */
+int tegra_dfll_suspend(struct device *dev)
+{
+	struct tegra_dfll *td = dev_get_drvdata(dev);
+
+	if (dfll_is_running(td)) {
+		dev_err(td->dev, "DFLL still enabled while suspending\n");
+		return -EBUSY;
+	}
+
+	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
+
+	return 0;
+}
+EXPORT_SYMBOL(tegra_dfll_suspend);
+
+/**
+ * tegra_dfll_resume - reinitialize DFLL on resume
+ * @dev: DFLL instance
+ *
+ * DFLL is disabled and reset during suspend and resume.
+ * So, reinitialize the DFLL IP block back for use.
+ * DFLL clock is enabled later in closed loop mode by CPUFreq
+ * driver before switching its clock source to DFLL output.
+ */
+int tegra_dfll_resume(struct device *dev)
+{
+	struct tegra_dfll *td = dev_get_drvdata(dev);
+
+	reset_control_deassert(td->dfll_rst);
+	reset_control_deassert(td->dvco_rst);
+
+	pm_runtime_get_sync(td->dev);
+
+	dfll_set_mode(td, DFLL_DISABLED);
+	dfll_set_default_params(td);
+
+	if (td->soc->init_clock_trimmers)
+		td->soc->init_clock_trimmers();
+
+	dfll_set_open_loop_config(td);
+
+	dfll_init_out_if(td);
+
+	pm_runtime_put_sync(td->dev);
+
+	return 0;
+}
+EXPORT_SYMBOL(tegra_dfll_resume);
+
+/*
+ * DT data fetch
+ */
+
+/*
+ * Find a PMIC voltage register-to-voltage mapping for the given voltage.
+ * An exact voltage match is required.
+ */
+static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV)
+{
+	int i, n_voltages, reg_uV,reg_volt_id, align_step;
+
+	if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM))
+		return -EINVAL;
+
+	align_step = uV / td->soc->alignment.step_uv;
+	n_voltages = regulator_count_voltages(td->vdd_reg);
+	for (i = 0; i < n_voltages; i++) {
+		reg_uV = regulator_list_voltage(td->vdd_reg, i);
+		if (reg_uV < 0)
+			break;
+
+		reg_volt_id = reg_uV / td->soc->alignment.step_uv;
+
+		if (align_step == reg_volt_id)
+			return i;
+	}
+
+	dev_err(td->dev, "no voltage map entry for %d uV\n", uV);
+	return -EINVAL;
+}
+
+/*
+ * Find a PMIC voltage register-to-voltage mapping for the given voltage,
+ * rounding up to the closest supported voltage.
+ * */
+static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV)
+{
+	int i, n_voltages, reg_uV, reg_volt_id, align_step;
+
+	if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM))
+		return -EINVAL;
+
+	align_step = uV / td->soc->alignment.step_uv;
+	n_voltages = regulator_count_voltages(td->vdd_reg);
+	for (i = 0; i < n_voltages; i++) {
+		reg_uV = regulator_list_voltage(td->vdd_reg, i);
+		if (reg_uV < 0)
+			break;
+
+		reg_volt_id = reg_uV / td->soc->alignment.step_uv;
+
+		if (align_step <= reg_volt_id)
+			return i;
+	}
+
+	dev_err(td->dev, "no voltage map entry rounding to %d uV\n", uV);
+	return -EINVAL;
+}
+
+/*
+ * dfll_build_pwm_lut - build the PWM regulator lookup table
+ * @td: DFLL instance
+ * @v_max: Vmax from OPP table
+ *
+ * Look-up table in h/w is ignored when PWM is used as DFLL interface to PMIC.
+ * In this case closed loop output is controlling duty cycle directly. The s/w
+ * look-up that maps PWM duty cycle to voltage is still built by this function.
+ */
+static int dfll_build_pwm_lut(struct tegra_dfll *td, unsigned long v_max)
+{
+	int i;
+	unsigned long rate, reg_volt;
+	u8 lut_bottom = MAX_DFLL_VOLTAGES;
+	int v_min = td->soc->cvb->min_millivolts * 1000;
+
+	for (i = 0; i < MAX_DFLL_VOLTAGES; i++) {
+		reg_volt = td->lut_uv[i];
+
+		/* since opp voltage is exact mv */
+		reg_volt = (reg_volt / 1000) * 1000;
+		if (reg_volt > v_max)
+			break;
+
+		td->lut[i] = i;
+		if ((lut_bottom == MAX_DFLL_VOLTAGES) && (reg_volt >= v_min))
+			lut_bottom = i;
+	}
+
+	/* determine voltage boundaries */
+	td->lut_size = i;
+	if ((lut_bottom == MAX_DFLL_VOLTAGES) ||
+	    (lut_bottom + 1 >= td->lut_size)) {
+		dev_err(td->dev, "no voltage above DFLL minimum %d mV\n",
+			td->soc->cvb->min_millivolts);
+		return -EINVAL;
+	}
+	td->lut_bottom = lut_bottom;
+
+	/* determine rate boundaries */
+	rate = get_dvco_rate_below(td, td->lut_bottom);
+	if (!rate) {
+		dev_err(td->dev, "no opp below DFLL minimum voltage %d mV\n",
+			td->soc->cvb->min_millivolts);
+		return -EINVAL;
+	}
+	td->dvco_rate_min = rate;
+
+	return 0;
+}
+
+/**
+ * dfll_build_i2c_lut - build the I2C voltage register lookup table
+ * @td: DFLL instance
+ * @v_max: Vmax from OPP table
+ *
+ * The DFLL hardware has 33 bytes of look-up table RAM that must be filled with
+ * PMIC voltage register values that span the entire DFLL operating range.
+ * This function builds the look-up table based on the OPP table provided by
+ * the soc-specific platform driver (td->soc->opp_dev) and the PMIC
+ * register-to-voltage mapping queried from the regulator framework.
+ *
+ * On success, fills in td->lut and returns 0, or -err on failure.
+ */
+static int dfll_build_i2c_lut(struct tegra_dfll *td, unsigned long v_max)
+{
+	unsigned long rate, v, v_opp;
+	int ret = -EINVAL;
+	int j, selector, lut;
+
+	v = td->soc->cvb->min_millivolts * 1000;
+	lut = find_vdd_map_entry_exact(td, v);
+	if (lut < 0)
+		goto out;
+	td->lut[0] = lut;
+	td->lut_bottom = 0;
+
+	for (j = 1, rate = 0; ; rate++) {
+		struct dev_pm_opp *opp;
+
+		opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
+		if (IS_ERR(opp))
+			break;
+		v_opp = dev_pm_opp_get_voltage(opp);
+
+		if (v_opp <= td->soc->cvb->min_millivolts * 1000)
+			td->dvco_rate_min = dev_pm_opp_get_freq(opp);
+
+		dev_pm_opp_put(opp);
+
+		for (;;) {
+			v += max(1UL, (v_max - v) / (MAX_DFLL_VOLTAGES - j));
+			if (v >= v_opp)
+				break;
+
+			selector = find_vdd_map_entry_min(td, v);
+			if (selector < 0)
+				goto out;
+			if (selector != td->lut[j - 1])
+				td->lut[j++] = selector;
+		}
+
+		v = (j == MAX_DFLL_VOLTAGES - 1) ? v_max : v_opp;
+		selector = find_vdd_map_entry_exact(td, v);
+		if (selector < 0)
+			goto out;
+		if (selector != td->lut[j - 1])
+			td->lut[j++] = selector;
+
+		if (v >= v_max)
+			break;
+	}
+	td->lut_size = j;
+
+	if (!td->dvco_rate_min)
+		dev_err(td->dev, "no opp above DFLL minimum voltage %d mV\n",
+			td->soc->cvb->min_millivolts);
+	else {
+		ret = 0;
+		for (j = 0; j < td->lut_size; j++)
+			td->lut_uv[j] =
+				regulator_list_voltage(td->vdd_reg,
+						       td->lut[j]);
+	}
+
+out:
+	return ret;
+}
+
+static int dfll_build_lut(struct tegra_dfll *td)
+{
+	unsigned long rate, v_max;
+	struct dev_pm_opp *opp;
+
+	rate = ULONG_MAX;
+	opp = dev_pm_opp_find_freq_floor(td->soc->dev, &rate);
+	if (IS_ERR(opp)) {
+		dev_err(td->dev, "couldn't get vmax opp, empty opp table?\n");
+		return -EINVAL;
+	}
+	v_max = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+		return dfll_build_pwm_lut(td, v_max);
+	else
+		return dfll_build_i2c_lut(td, v_max);
+}
+
+/**
+ * read_dt_param - helper function for reading required parameters from the DT
+ * @td: DFLL instance
+ * @param: DT property name
+ * @dest: output pointer for the value read
+ *
+ * Read a required numeric parameter from the DFLL device node, or complain
+ * if the property doesn't exist. Returns a boolean indicating success for
+ * easy chaining of multiple calls to this function.
+ */
+static bool read_dt_param(struct tegra_dfll *td, const char *param, u32 *dest)
+{
+	int err = of_property_read_u32(td->dev->of_node, param, dest);
+
+	if (err < 0) {
+		dev_err(td->dev, "failed to read DT parameter %s: %d\n",
+			param, err);
+		return false;
+	}
+
+	return true;
+}
+
+/**
+ * dfll_fetch_i2c_params - query PMIC I2C params from DT & regulator subsystem
+ * @td: DFLL instance
+ *
+ * Read all the parameters required for operation in I2C mode. The parameters
+ * can originate from the device tree or the regulator subsystem.
+ * Returns 0 on success or -err on failure.
+ */
+static int dfll_fetch_i2c_params(struct tegra_dfll *td)
+{
+	struct regmap *regmap;
+	struct device *i2c_dev;
+	struct i2c_client *i2c_client;
+	int vsel_reg, vsel_mask;
+	int ret;
+
+	if (!read_dt_param(td, "nvidia,i2c-fs-rate", &td->i2c_fs_rate))
+		return -EINVAL;
+
+	regmap = regulator_get_regmap(td->vdd_reg);
+	i2c_dev = regmap_get_device(regmap);
+	i2c_client = to_i2c_client(i2c_dev);
+
+	td->i2c_slave_addr = i2c_client->addr;
+
+	ret = regulator_get_hardware_vsel_register(td->vdd_reg,
+						   &vsel_reg,
+						   &vsel_mask);
+	if (ret < 0) {
+		dev_err(td->dev,
+			"regulator unsuitable for DFLL I2C operation\n");
+		return -EINVAL;
+	}
+	td->i2c_reg = vsel_reg;
+
+	return 0;
+}
+
+static int dfll_fetch_pwm_params(struct tegra_dfll *td)
+{
+	int ret, i;
+	u32 pwm_period;
+
+	if (!td->soc->alignment.step_uv || !td->soc->alignment.offset_uv) {
+		dev_err(td->dev,
+			"Missing step or alignment info for PWM regulator");
+		return -EINVAL;
+	}
+	for (i = 0; i < MAX_DFLL_VOLTAGES; i++)
+		td->lut_uv[i] = td->soc->alignment.offset_uv +
+				i * td->soc->alignment.step_uv;
+
+	ret = read_dt_param(td, "nvidia,pwm-tristate-microvolts",
+			    &td->reg_init_uV);
+	if (!ret) {
+		dev_err(td->dev, "couldn't get initialized voltage\n");
+		return -EINVAL;
+	}
+
+	ret = read_dt_param(td, "nvidia,pwm-period-nanoseconds", &pwm_period);
+	if (!ret) {
+		dev_err(td->dev, "couldn't get PWM period\n");
+		return -EINVAL;
+	}
+	td->pwm_rate = (NSEC_PER_SEC / pwm_period) * (MAX_DFLL_VOLTAGES - 1);
+
+	td->pwm_pin = devm_pinctrl_get(td->dev);
+	if (IS_ERR(td->pwm_pin)) {
+		dev_err(td->dev, "DT: missing pinctrl device\n");
+		return PTR_ERR(td->pwm_pin);
+	}
+
+	td->pwm_enable_state = pinctrl_lookup_state(td->pwm_pin,
+						    "dvfs_pwm_enable");
+	if (IS_ERR(td->pwm_enable_state)) {
+		dev_err(td->dev, "DT: missing pwm enabled state\n");
+		return PTR_ERR(td->pwm_enable_state);
+	}
+
+	td->pwm_disable_state = pinctrl_lookup_state(td->pwm_pin,
+						     "dvfs_pwm_disable");
+	if (IS_ERR(td->pwm_disable_state)) {
+		dev_err(td->dev, "DT: missing pwm disabled state\n");
+		return PTR_ERR(td->pwm_disable_state);
+	}
+
+	return 0;
+}
+
+/**
+ * dfll_fetch_common_params - read DFLL parameters from the device tree
+ * @td: DFLL instance
+ *
+ * Read all the DT parameters that are common to both I2C and PWM operation.
+ * Returns 0 on success or -EINVAL on any failure.
+ */
+static int dfll_fetch_common_params(struct tegra_dfll *td)
+{
+	bool ok = true;
+
+	ok &= read_dt_param(td, "nvidia,droop-ctrl", &td->droop_ctrl);
+	ok &= read_dt_param(td, "nvidia,sample-rate", &td->sample_rate);
+	ok &= read_dt_param(td, "nvidia,force-mode", &td->force_mode);
+	ok &= read_dt_param(td, "nvidia,cf", &td->cf);
+	ok &= read_dt_param(td, "nvidia,ci", &td->ci);
+	ok &= read_dt_param(td, "nvidia,cg", &td->cg);
+	td->cg_scale = of_property_read_bool(td->dev->of_node,
+					     "nvidia,cg-scale");
+
+	if (of_property_read_string(td->dev->of_node, "clock-output-names",
+				    &td->output_clock_name)) {
+		dev_err(td->dev, "missing clock-output-names property\n");
+		ok = false;
+	}
+
+	return ok ? 0 : -EINVAL;
+}
+
+/*
+ * API exported to per-SoC platform drivers
+ */
+
+/**
+ * tegra_dfll_register - probe a Tegra DFLL device
+ * @pdev: DFLL platform_device *
+ * @soc: Per-SoC integration and characterization data for this DFLL instance
+ *
+ * Probe and initialize a DFLL device instance. Intended to be called
+ * by a SoC-specific shim driver that passes in per-SoC integration
+ * and configuration data via @soc. Returns 0 on success or -err on failure.
+ */
+int tegra_dfll_register(struct platform_device *pdev,
+			struct tegra_dfll_soc_data *soc)
+{
+	struct resource *mem;
+	struct tegra_dfll *td;
+	int ret;
+
+	if (!soc) {
+		dev_err(&pdev->dev, "no tegra_dfll_soc_data provided\n");
+		return -EINVAL;
+	}
+
+	td = devm_kzalloc(&pdev->dev, sizeof(*td), GFP_KERNEL);
+	if (!td)
+		return -ENOMEM;
+	td->dev = &pdev->dev;
+	platform_set_drvdata(pdev, td);
+
+	td->soc = soc;
+
+	td->dfll_rst = devm_reset_control_get_optional(td->dev, "dfll");
+	if (IS_ERR(td->dfll_rst)) {
+		dev_err(td->dev, "couldn't get dfll reset\n");
+		return PTR_ERR(td->dfll_rst);
+	}
+
+	td->dvco_rst = devm_reset_control_get(td->dev, "dvco");
+	if (IS_ERR(td->dvco_rst)) {
+		dev_err(td->dev, "couldn't get dvco reset\n");
+		return PTR_ERR(td->dvco_rst);
+	}
+
+	ret = dfll_fetch_common_params(td);
+	if (ret) {
+		dev_err(td->dev, "couldn't parse device tree parameters\n");
+		return ret;
+	}
+
+	if (of_property_read_bool(td->dev->of_node, "nvidia,pwm-to-pmic")) {
+		td->pmu_if = TEGRA_DFLL_PMU_PWM;
+		ret = dfll_fetch_pwm_params(td);
+	} else  {
+		td->vdd_reg = devm_regulator_get(td->dev, "vdd-cpu");
+		if (IS_ERR(td->vdd_reg)) {
+			dev_err(td->dev, "couldn't get vdd_cpu regulator\n");
+			return PTR_ERR(td->vdd_reg);
+		}
+		td->pmu_if = TEGRA_DFLL_PMU_I2C;
+		ret = dfll_fetch_i2c_params(td);
+	}
+	if (ret)
+		return ret;
+
+	ret = dfll_build_lut(td);
+	if (ret) {
+		dev_err(td->dev, "couldn't build LUT\n");
+		return ret;
+	}
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!mem) {
+		dev_err(td->dev, "no control register resource\n");
+		return -ENODEV;
+	}
+
+	td->base = devm_ioremap(td->dev, mem->start, resource_size(mem));
+	if (!td->base) {
+		dev_err(td->dev, "couldn't ioremap DFLL control registers\n");
+		return -ENODEV;
+	}
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (!mem) {
+		dev_err(td->dev, "no i2c_base resource\n");
+		return -ENODEV;
+	}
+
+	td->i2c_base = devm_ioremap(td->dev, mem->start, resource_size(mem));
+	if (!td->i2c_base) {
+		dev_err(td->dev, "couldn't ioremap i2c_base resource\n");
+		return -ENODEV;
+	}
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	if (!mem) {
+		dev_err(td->dev, "no i2c_controller_base resource\n");
+		return -ENODEV;
+	}
+
+	td->i2c_controller_base = devm_ioremap(td->dev, mem->start,
+					       resource_size(mem));
+	if (!td->i2c_controller_base) {
+		dev_err(td->dev,
+			"couldn't ioremap i2c_controller_base resource\n");
+		return -ENODEV;
+	}
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+	if (!mem) {
+		dev_err(td->dev, "no lut_base resource\n");
+		return -ENODEV;
+	}
+
+	td->lut_base = devm_ioremap(td->dev, mem->start, resource_size(mem));
+	if (!td->lut_base) {
+		dev_err(td->dev,
+			"couldn't ioremap lut_base resource\n");
+		return -ENODEV;
+	}
+
+	ret = dfll_init_clks(td);
+	if (ret) {
+		dev_err(&pdev->dev, "DFLL clock init error\n");
+		return ret;
+	}
+
+	/* Enable the clocks and set the device up */
+	ret = dfll_init(td);
+	if (ret)
+		return ret;
+
+	ret = dfll_register_clk(td);
+	if (ret) {
+		dev_err(&pdev->dev, "DFLL clk registration failed\n");
+		return ret;
+	}
+
+	dfll_debug_init(td);
+
+	return 0;
+}
+EXPORT_SYMBOL(tegra_dfll_register);
+
+/**
+ * tegra_dfll_unregister - release all of the DFLL driver resources for a device
+ * @pdev: DFLL platform_device *
+ *
+ * Unbind this driver from the DFLL hardware device represented by
+ * @pdev. The DFLL must be disabled for this to succeed. Returns a
+ * soc pointer upon success or -EBUSY if the DFLL is still active.
+ */
+struct tegra_dfll_soc_data *tegra_dfll_unregister(struct platform_device *pdev)
+{
+	struct tegra_dfll *td = platform_get_drvdata(pdev);
+
+	/* Try to prevent removal while the DFLL is active */
+	if (td->mode != DFLL_DISABLED) {
+		dev_err(&pdev->dev,
+			"must disable DFLL before removing driver\n");
+		return ERR_PTR(-EBUSY);
+	}
+
+	debugfs_remove_recursive(td->debugfs_dir);
+
+	dfll_unregister_clk(td);
+	pm_runtime_disable(&pdev->dev);
+
+	clk_unprepare(td->ref_clk);
+	clk_unprepare(td->soc_clk);
+	clk_unprepare(td->i2c_clk);
+
+	reset_control_assert(td->dvco_rst);
+	reset_control_assert(td->dfll_rst);
+
+	return td->soc;
+}
+EXPORT_SYMBOL(tegra_dfll_unregister);