Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 536 insertions, 0 deletions

diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c
new file mode 100644
index 000000000..bdffc6543
--- /dev/null
+++ b/drivers/misc/eeprom/at25.c
@@ -0,0 +1,536 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for most of the SPI EEPROMs, such as Atmel AT25 models
+ * and Cypress FRAMs FM25 models.
+ *
+ * Copyright (C) 2006 David Brownell
+ */
+
+#include <linux/bits.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+#include <linux/spi/eeprom.h>
+#include <linux/spi/spi.h>
+
+#include <linux/nvmem-provider.h>
+
+/*
+ * NOTE: this is an *EEPROM* driver. The vagaries of product naming
+ * mean that some AT25 products are EEPROMs, and others are FLASH.
+ * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
+ * not this one!
+ *
+ * EEPROMs that can be used with this driver include, for example:
+ *   AT25M02, AT25128B
+ */
+
+#define	FM25_SN_LEN	8		/* serial number length */
+#define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
+
+struct at25_data {
+	struct spi_eeprom	chip;
+	struct spi_device	*spi;
+	struct mutex		lock;
+	unsigned		addrlen;
+	struct nvmem_config	nvmem_config;
+	struct nvmem_device	*nvmem;
+	u8 sernum[FM25_SN_LEN];
+	u8 command[EE_MAXADDRLEN + 1];
+};
+
+#define	AT25_WREN	0x06		/* latch the write enable */
+#define	AT25_WRDI	0x04		/* reset the write enable */
+#define	AT25_RDSR	0x05		/* read status register */
+#define	AT25_WRSR	0x01		/* write status register */
+#define	AT25_READ	0x03		/* read byte(s) */
+#define	AT25_WRITE	0x02		/* write byte(s)/sector */
+#define	FM25_SLEEP	0xb9		/* enter sleep mode */
+#define	FM25_RDID	0x9f		/* read device ID */
+#define	FM25_RDSN	0xc3		/* read S/N */
+
+#define	AT25_SR_nRDY	0x01		/* nRDY = write-in-progress */
+#define	AT25_SR_WEN	0x02		/* write enable (latched) */
+#define	AT25_SR_BP0	0x04		/* BP for software writeprotect */
+#define	AT25_SR_BP1	0x08
+#define	AT25_SR_WPEN	0x80		/* writeprotect enable */
+
+#define	AT25_INSTR_BIT3	0x08		/* additional address bit in instr */
+
+#define	FM25_ID_LEN	9		/* ID length */
+
+/*
+ * Specs often allow 5ms for a page write, sometimes 20ms;
+ * it's important to recover from write timeouts.
+ */
+#define	EE_TIMEOUT	25
+
+/*-------------------------------------------------------------------------*/
+
+#define	io_limit	PAGE_SIZE	/* bytes */
+
+static int at25_ee_read(void *priv, unsigned int offset,
+			void *val, size_t count)
+{
+	struct at25_data *at25 = priv;
+	char *buf = val;
+	size_t max_chunk = spi_max_transfer_size(at25->spi);
+	unsigned int msg_offset = offset;
+	size_t bytes_left = count;
+	size_t segment;
+	u8			*cp;
+	ssize_t			status;
+	struct spi_transfer	t[2];
+	struct spi_message	m;
+	u8			instr;
+
+	if (unlikely(offset >= at25->chip.byte_len))
+		return -EINVAL;
+	if ((offset + count) > at25->chip.byte_len)
+		count = at25->chip.byte_len - offset;
+	if (unlikely(!count))
+		return -EINVAL;
+
+	do {
+		segment = min(bytes_left, max_chunk);
+		cp = at25->command;
+
+		instr = AT25_READ;
+		if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+			if (msg_offset >= BIT(at25->addrlen * 8))
+				instr |= AT25_INSTR_BIT3;
+
+		mutex_lock(&at25->lock);
+
+		*cp++ = instr;
+
+		/* 8/16/24-bit address is written MSB first */
+		switch (at25->addrlen) {
+		default:	/* case 3 */
+			*cp++ = msg_offset >> 16;
+			fallthrough;
+		case 2:
+			*cp++ = msg_offset >> 8;
+			fallthrough;
+		case 1:
+		case 0:	/* can't happen: for better code generation */
+			*cp++ = msg_offset >> 0;
+		}
+
+		spi_message_init(&m);
+		memset(t, 0, sizeof(t));
+
+		t[0].tx_buf = at25->command;
+		t[0].len = at25->addrlen + 1;
+		spi_message_add_tail(&t[0], &m);
+
+		t[1].rx_buf = buf;
+		t[1].len = segment;
+		spi_message_add_tail(&t[1], &m);
+
+		status = spi_sync(at25->spi, &m);
+
+		mutex_unlock(&at25->lock);
+
+		if (status)
+			return status;
+
+		msg_offset += segment;
+		buf += segment;
+		bytes_left -= segment;
+	} while (bytes_left > 0);
+
+	dev_dbg(&at25->spi->dev, "read %zu bytes at %d\n",
+		count, offset);
+	return 0;
+}
+
+/* Read extra registers as ID or serial number */
+static int fm25_aux_read(struct at25_data *at25, u8 *buf, uint8_t command,
+			 int len)
+{
+	int status;
+	struct spi_transfer t[2];
+	struct spi_message m;
+
+	spi_message_init(&m);
+	memset(t, 0, sizeof(t));
+
+	t[0].tx_buf = at25->command;
+	t[0].len = 1;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].rx_buf = buf;
+	t[1].len = len;
+	spi_message_add_tail(&t[1], &m);
+
+	mutex_lock(&at25->lock);
+
+	at25->command[0] = command;
+
+	status = spi_sync(at25->spi, &m);
+	dev_dbg(&at25->spi->dev, "read %d aux bytes --> %d\n", len, status);
+
+	mutex_unlock(&at25->lock);
+	return status;
+}
+
+static ssize_t sernum_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct at25_data *at25;
+
+	at25 = dev_get_drvdata(dev);
+	return sysfs_emit(buf, "%*ph\n", (int)sizeof(at25->sernum), at25->sernum);
+}
+static DEVICE_ATTR_RO(sernum);
+
+static struct attribute *sernum_attrs[] = {
+	&dev_attr_sernum.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(sernum);
+
+static int at25_ee_write(void *priv, unsigned int off, void *val, size_t count)
+{
+	struct at25_data *at25 = priv;
+	size_t maxsz = spi_max_transfer_size(at25->spi);
+	const char *buf = val;
+	int			status = 0;
+	unsigned		buf_size;
+	u8			*bounce;
+
+	if (unlikely(off >= at25->chip.byte_len))
+		return -EFBIG;
+	if ((off + count) > at25->chip.byte_len)
+		count = at25->chip.byte_len - off;
+	if (unlikely(!count))
+		return -EINVAL;
+
+	/* Temp buffer starts with command and address */
+	buf_size = at25->chip.page_size;
+	if (buf_size > io_limit)
+		buf_size = io_limit;
+	bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
+	if (!bounce)
+		return -ENOMEM;
+
+	/*
+	 * For write, rollover is within the page ... so we write at
+	 * most one page, then manually roll over to the next page.
+	 */
+	mutex_lock(&at25->lock);
+	do {
+		unsigned long	timeout, retries;
+		unsigned	segment;
+		unsigned	offset = off;
+		u8		*cp = bounce;
+		int		sr;
+		u8		instr;
+
+		*cp = AT25_WREN;
+		status = spi_write(at25->spi, cp, 1);
+		if (status < 0) {
+			dev_dbg(&at25->spi->dev, "WREN --> %d\n", status);
+			break;
+		}
+
+		instr = AT25_WRITE;
+		if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+			if (offset >= BIT(at25->addrlen * 8))
+				instr |= AT25_INSTR_BIT3;
+		*cp++ = instr;
+
+		/* 8/16/24-bit address is written MSB first */
+		switch (at25->addrlen) {
+		default:	/* case 3 */
+			*cp++ = offset >> 16;
+			fallthrough;
+		case 2:
+			*cp++ = offset >> 8;
+			fallthrough;
+		case 1:
+		case 0:	/* can't happen: for better code generation */
+			*cp++ = offset >> 0;
+		}
+
+		/* Write as much of a page as we can */
+		segment = buf_size - (offset % buf_size);
+		if (segment > count)
+			segment = count;
+		if (segment > maxsz)
+			segment = maxsz;
+		memcpy(cp, buf, segment);
+		status = spi_write(at25->spi, bounce,
+				segment + at25->addrlen + 1);
+		dev_dbg(&at25->spi->dev, "write %u bytes at %u --> %d\n",
+			segment, offset, status);
+		if (status < 0)
+			break;
+
+		/*
+		 * REVISIT this should detect (or prevent) failed writes
+		 * to read-only sections of the EEPROM...
+		 */
+
+		/* Wait for non-busy status */
+		timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
+		retries = 0;
+		do {
+
+			sr = spi_w8r8(at25->spi, AT25_RDSR);
+			if (sr < 0 || (sr & AT25_SR_nRDY)) {
+				dev_dbg(&at25->spi->dev,
+					"rdsr --> %d (%02x)\n", sr, sr);
+				/* at HZ=100, this is sloooow */
+				msleep(1);
+				continue;
+			}
+			if (!(sr & AT25_SR_nRDY))
+				break;
+		} while (retries++ < 3 || time_before_eq(jiffies, timeout));
+
+		if ((sr < 0) || (sr & AT25_SR_nRDY)) {
+			dev_err(&at25->spi->dev,
+				"write %u bytes offset %u, timeout after %u msecs\n",
+				segment, offset,
+				jiffies_to_msecs(jiffies -
+					(timeout - EE_TIMEOUT)));
+			status = -ETIMEDOUT;
+			break;
+		}
+
+		off += segment;
+		buf += segment;
+		count -= segment;
+
+	} while (count > 0);
+
+	mutex_unlock(&at25->lock);
+
+	kfree(bounce);
+	return status;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static int at25_fw_to_chip(struct device *dev, struct spi_eeprom *chip)
+{
+	u32 val;
+	int err;
+
+	strscpy(chip->name, "at25", sizeof(chip->name));
+
+	err = device_property_read_u32(dev, "size", &val);
+	if (err)
+		err = device_property_read_u32(dev, "at25,byte-len", &val);
+	if (err) {
+		dev_err(dev, "Error: missing \"size\" property\n");
+		return err;
+	}
+	chip->byte_len = val;
+
+	err = device_property_read_u32(dev, "pagesize", &val);
+	if (err)
+		err = device_property_read_u32(dev, "at25,page-size", &val);
+	if (err) {
+		dev_err(dev, "Error: missing \"pagesize\" property\n");
+		return err;
+	}
+	chip->page_size = val;
+
+	err = device_property_read_u32(dev, "address-width", &val);
+	if (err) {
+		err = device_property_read_u32(dev, "at25,addr-mode", &val);
+		if (err) {
+			dev_err(dev, "Error: missing \"address-width\" property\n");
+			return err;
+		}
+		chip->flags = (u16)val;
+	} else {
+		switch (val) {
+		case 9:
+			chip->flags |= EE_INSTR_BIT3_IS_ADDR;
+			fallthrough;
+		case 8:
+			chip->flags |= EE_ADDR1;
+			break;
+		case 16:
+			chip->flags |= EE_ADDR2;
+			break;
+		case 24:
+			chip->flags |= EE_ADDR3;
+			break;
+		default:
+			dev_err(dev,
+				"Error: bad \"address-width\" property: %u\n",
+				val);
+			return -ENODEV;
+		}
+		if (device_property_present(dev, "read-only"))
+			chip->flags |= EE_READONLY;
+	}
+	return 0;
+}
+
+static int at25_fram_to_chip(struct device *dev, struct spi_eeprom *chip)
+{
+	struct at25_data *at25 = container_of(chip, struct at25_data, chip);
+	u8 sernum[FM25_SN_LEN];
+	u8 id[FM25_ID_LEN];
+	int i;
+
+	strscpy(chip->name, "fm25", sizeof(chip->name));
+
+	/* Get ID of chip */
+	fm25_aux_read(at25, id, FM25_RDID, FM25_ID_LEN);
+	if (id[6] != 0xc2) {
+		dev_err(dev, "Error: no Cypress FRAM (id %02x)\n", id[6]);
+		return -ENODEV;
+	}
+	/* Set size found in ID */
+	if (id[7] < 0x21 || id[7] > 0x26) {
+		dev_err(dev, "Error: unsupported size (id %02x)\n", id[7]);
+		return -ENODEV;
+	}
+
+	chip->byte_len = BIT(id[7] - 0x21 + 4) * 1024;
+	if (chip->byte_len > 64 * 1024)
+		chip->flags |= EE_ADDR3;
+	else
+		chip->flags |= EE_ADDR2;
+
+	if (id[8]) {
+		fm25_aux_read(at25, sernum, FM25_RDSN, FM25_SN_LEN);
+		/* Swap byte order */
+		for (i = 0; i < FM25_SN_LEN; i++)
+			at25->sernum[i] = sernum[FM25_SN_LEN - 1 - i];
+	}
+
+	chip->page_size = PAGE_SIZE;
+	return 0;
+}
+
+static const struct of_device_id at25_of_match[] = {
+	{ .compatible = "atmel,at25" },
+	{ .compatible = "cypress,fm25" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, at25_of_match);
+
+static const struct spi_device_id at25_spi_ids[] = {
+	{ .name = "at25" },
+	{ .name = "fm25" },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, at25_spi_ids);
+
+static int at25_probe(struct spi_device *spi)
+{
+	struct at25_data	*at25 = NULL;
+	int			err;
+	int			sr;
+	struct spi_eeprom *pdata;
+	bool is_fram;
+
+	err = device_property_match_string(&spi->dev, "compatible", "cypress,fm25");
+	if (err >= 0)
+		is_fram = true;
+	else
+		is_fram = false;
+
+	/*
+	 * Ping the chip ... the status register is pretty portable,
+	 * unlike probing manufacturer IDs. We do expect that system
+	 * firmware didn't write it in the past few milliseconds!
+	 */
+	sr = spi_w8r8(spi, AT25_RDSR);
+	if (sr < 0 || sr & AT25_SR_nRDY) {
+		dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
+		return -ENXIO;
+	}
+
+	at25 = devm_kzalloc(&spi->dev, sizeof(*at25), GFP_KERNEL);
+	if (!at25)
+		return -ENOMEM;
+
+	mutex_init(&at25->lock);
+	at25->spi = spi;
+	spi_set_drvdata(spi, at25);
+
+	/* Chip description */
+	pdata = dev_get_platdata(&spi->dev);
+	if (pdata) {
+		at25->chip = *pdata;
+	} else {
+		if (is_fram)
+			err = at25_fram_to_chip(&spi->dev, &at25->chip);
+		else
+			err = at25_fw_to_chip(&spi->dev, &at25->chip);
+		if (err)
+			return err;
+	}
+
+	/* For now we only support 8/16/24 bit addressing */
+	if (at25->chip.flags & EE_ADDR1)
+		at25->addrlen = 1;
+	else if (at25->chip.flags & EE_ADDR2)
+		at25->addrlen = 2;
+	else if (at25->chip.flags & EE_ADDR3)
+		at25->addrlen = 3;
+	else {
+		dev_dbg(&spi->dev, "unsupported address type\n");
+		return -EINVAL;
+	}
+
+	at25->nvmem_config.type = is_fram ? NVMEM_TYPE_FRAM : NVMEM_TYPE_EEPROM;
+	at25->nvmem_config.name = dev_name(&spi->dev);
+	at25->nvmem_config.dev = &spi->dev;
+	at25->nvmem_config.read_only = at25->chip.flags & EE_READONLY;
+	at25->nvmem_config.root_only = true;
+	at25->nvmem_config.owner = THIS_MODULE;
+	at25->nvmem_config.compat = true;
+	at25->nvmem_config.base_dev = &spi->dev;
+	at25->nvmem_config.reg_read = at25_ee_read;
+	at25->nvmem_config.reg_write = at25_ee_write;
+	at25->nvmem_config.priv = at25;
+	at25->nvmem_config.stride = 1;
+	at25->nvmem_config.word_size = 1;
+	at25->nvmem_config.size = at25->chip.byte_len;
+
+	at25->nvmem = devm_nvmem_register(&spi->dev, &at25->nvmem_config);
+	if (IS_ERR(at25->nvmem))
+		return PTR_ERR(at25->nvmem);
+
+	dev_info(&spi->dev, "%d %s %s %s%s, pagesize %u\n",
+		 (at25->chip.byte_len < 1024) ?
+			at25->chip.byte_len : (at25->chip.byte_len / 1024),
+		 (at25->chip.byte_len < 1024) ? "Byte" : "KByte",
+		 at25->chip.name, is_fram ? "fram" : "eeprom",
+		 (at25->chip.flags & EE_READONLY) ? " (readonly)" : "",
+		 at25->chip.page_size);
+	return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static struct spi_driver at25_driver = {
+	.driver = {
+		.name		= "at25",
+		.of_match_table = at25_of_match,
+		.dev_groups	= sernum_groups,
+	},
+	.probe		= at25_probe,
+	.id_table	= at25_spi_ids,
+};
+
+module_spi_driver(at25_driver);
+
+MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
+MODULE_AUTHOR("David Brownell");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("spi:at25");