Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 956 insertions, 0 deletions

diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c
new file mode 100644
index 000000000..25bad4318
--- /dev/null
+++ b/drivers/mtd/devices/mtd_dataflash.c
@@ -0,0 +1,956 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Atmel AT45xxx DataFlash MTD driver for lightweight SPI framework
+ *
+ * Largely derived from at91_dataflash.c:
+ *  Copyright (C) 2003-2005 SAN People (Pty) Ltd
+*/
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/math64.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+/*
+ * DataFlash is a kind of SPI flash.  Most AT45 chips have two buffers in
+ * each chip, which may be used for double buffered I/O; but this driver
+ * doesn't (yet) use these for any kind of i/o overlap or prefetching.
+ *
+ * Sometimes DataFlash is packaged in MMC-format cards, although the
+ * MMC stack can't (yet?) distinguish between MMC and DataFlash
+ * protocols during enumeration.
+ */
+
+/* reads can bypass the buffers */
+#define OP_READ_CONTINUOUS	0xE8
+#define OP_READ_PAGE		0xD2
+
+/* group B requests can run even while status reports "busy" */
+#define OP_READ_STATUS		0xD7	/* group B */
+
+/* move data between host and buffer */
+#define OP_READ_BUFFER1		0xD4	/* group B */
+#define OP_READ_BUFFER2		0xD6	/* group B */
+#define OP_WRITE_BUFFER1	0x84	/* group B */
+#define OP_WRITE_BUFFER2	0x87	/* group B */
+
+/* erasing flash */
+#define OP_ERASE_PAGE		0x81
+#define OP_ERASE_BLOCK		0x50
+
+/* move data between buffer and flash */
+#define OP_TRANSFER_BUF1	0x53
+#define OP_TRANSFER_BUF2	0x55
+#define OP_MREAD_BUFFER1	0xD4
+#define OP_MREAD_BUFFER2	0xD6
+#define OP_MWERASE_BUFFER1	0x83
+#define OP_MWERASE_BUFFER2	0x86
+#define OP_MWRITE_BUFFER1	0x88	/* sector must be pre-erased */
+#define OP_MWRITE_BUFFER2	0x89	/* sector must be pre-erased */
+
+/* write to buffer, then write-erase to flash */
+#define OP_PROGRAM_VIA_BUF1	0x82
+#define OP_PROGRAM_VIA_BUF2	0x85
+
+/* compare buffer to flash */
+#define OP_COMPARE_BUF1		0x60
+#define OP_COMPARE_BUF2		0x61
+
+/* read flash to buffer, then write-erase to flash */
+#define OP_REWRITE_VIA_BUF1	0x58
+#define OP_REWRITE_VIA_BUF2	0x59
+
+/* newer chips report JEDEC manufacturer and device IDs; chip
+ * serial number and OTP bits; and per-sector writeprotect.
+ */
+#define OP_READ_ID		0x9F
+#define OP_READ_SECURITY	0x77
+#define OP_WRITE_SECURITY_REVC	0x9A
+#define OP_WRITE_SECURITY	0x9B	/* revision D */
+
+#define CFI_MFR_ATMEL		0x1F
+
+#define DATAFLASH_SHIFT_EXTID	24
+#define DATAFLASH_SHIFT_ID	40
+
+struct dataflash {
+	u8			command[4];
+	char			name[24];
+
+	unsigned short		page_offset;	/* offset in flash address */
+	unsigned int		page_size;	/* of bytes per page */
+
+	struct mutex		lock;
+	struct spi_device	*spi;
+
+	struct mtd_info		mtd;
+};
+
+static const struct spi_device_id dataflash_dev_ids[] = {
+	{ "at45" },
+	{ "dataflash" },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, dataflash_dev_ids);
+
+#ifdef CONFIG_OF
+static const struct of_device_id dataflash_dt_ids[] = {
+	{ .compatible = "atmel,at45", },
+	{ .compatible = "atmel,dataflash", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dataflash_dt_ids);
+#endif
+
+static const struct spi_device_id dataflash_spi_ids[] = {
+	{ .name = "at45", },
+	{ .name = "dataflash", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, dataflash_spi_ids);
+
+/* ......................................................................... */
+
+/*
+ * Return the status of the DataFlash device.
+ */
+static inline int dataflash_status(struct spi_device *spi)
+{
+	/* NOTE:  at45db321c over 25 MHz wants to write
+	 * a dummy byte after the opcode...
+	 */
+	return spi_w8r8(spi, OP_READ_STATUS);
+}
+
+/*
+ * Poll the DataFlash device until it is READY.
+ * This usually takes 5-20 msec or so; more for sector erase.
+ */
+static int dataflash_waitready(struct spi_device *spi)
+{
+	int	status;
+
+	for (;;) {
+		status = dataflash_status(spi);
+		if (status < 0) {
+			dev_dbg(&spi->dev, "status %d?\n", status);
+			status = 0;
+		}
+
+		if (status & (1 << 7))	/* RDY/nBSY */
+			return status;
+
+		usleep_range(3000, 4000);
+	}
+}
+
+/* ......................................................................... */
+
+/*
+ * Erase pages of flash.
+ */
+static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+	struct dataflash	*priv = mtd->priv;
+	struct spi_device	*spi = priv->spi;
+	struct spi_transfer	x = { };
+	struct spi_message	msg;
+	unsigned		blocksize = priv->page_size << 3;
+	u8			*command;
+	u32			rem;
+
+	dev_dbg(&spi->dev, "erase addr=0x%llx len 0x%llx\n",
+		(long long)instr->addr, (long long)instr->len);
+
+	div_u64_rem(instr->len, priv->page_size, &rem);
+	if (rem)
+		return -EINVAL;
+	div_u64_rem(instr->addr, priv->page_size, &rem);
+	if (rem)
+		return -EINVAL;
+
+	spi_message_init(&msg);
+
+	x.tx_buf = command = priv->command;
+	x.len = 4;
+	spi_message_add_tail(&x, &msg);
+
+	mutex_lock(&priv->lock);
+	while (instr->len > 0) {
+		unsigned int	pageaddr;
+		int		status;
+		int		do_block;
+
+		/* Calculate flash page address; use block erase (for speed) if
+		 * we're at a block boundary and need to erase the whole block.
+		 */
+		pageaddr = div_u64(instr->addr, priv->page_size);
+		do_block = (pageaddr & 0x7) == 0 && instr->len >= blocksize;
+		pageaddr = pageaddr << priv->page_offset;
+
+		command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
+		command[1] = (u8)(pageaddr >> 16);
+		command[2] = (u8)(pageaddr >> 8);
+		command[3] = 0;
+
+		dev_dbg(&spi->dev, "ERASE %s: (%x) %x %x %x [%i]\n",
+			do_block ? "block" : "page",
+			command[0], command[1], command[2], command[3],
+			pageaddr);
+
+		status = spi_sync(spi, &msg);
+		(void) dataflash_waitready(spi);
+
+		if (status < 0) {
+			dev_err(&spi->dev, "erase %x, err %d\n",
+				pageaddr, status);
+			/* REVISIT:  can retry instr->retries times; or
+			 * giveup and instr->fail_addr = instr->addr;
+			 */
+			continue;
+		}
+
+		if (do_block) {
+			instr->addr += blocksize;
+			instr->len -= blocksize;
+		} else {
+			instr->addr += priv->page_size;
+			instr->len -= priv->page_size;
+		}
+	}
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+/*
+ * Read from the DataFlash device.
+ *   from   : Start offset in flash device
+ *   len    : Amount to read
+ *   retlen : About of data actually read
+ *   buf    : Buffer containing the data
+ */
+static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len,
+			       size_t *retlen, u_char *buf)
+{
+	struct dataflash	*priv = mtd->priv;
+	struct spi_transfer	x[2] = { };
+	struct spi_message	msg;
+	unsigned int		addr;
+	u8			*command;
+	int			status;
+
+	dev_dbg(&priv->spi->dev, "read 0x%x..0x%x\n",
+		  (unsigned int)from, (unsigned int)(from + len));
+
+	/* Calculate flash page/byte address */
+	addr = (((unsigned)from / priv->page_size) << priv->page_offset)
+		+ ((unsigned)from % priv->page_size);
+
+	command = priv->command;
+
+	dev_dbg(&priv->spi->dev, "READ: (%x) %x %x %x\n",
+		command[0], command[1], command[2], command[3]);
+
+	spi_message_init(&msg);
+
+	x[0].tx_buf = command;
+	x[0].len = 8;
+	spi_message_add_tail(&x[0], &msg);
+
+	x[1].rx_buf = buf;
+	x[1].len = len;
+	spi_message_add_tail(&x[1], &msg);
+
+	mutex_lock(&priv->lock);
+
+	/* Continuous read, max clock = f(car) which may be less than
+	 * the peak rate available.  Some chips support commands with
+	 * fewer "don't care" bytes.  Both buffers stay unchanged.
+	 */
+	command[0] = OP_READ_CONTINUOUS;
+	command[1] = (u8)(addr >> 16);
+	command[2] = (u8)(addr >> 8);
+	command[3] = (u8)(addr >> 0);
+	/* plus 4 "don't care" bytes */
+
+	status = spi_sync(priv->spi, &msg);
+	mutex_unlock(&priv->lock);
+
+	if (status >= 0) {
+		*retlen = msg.actual_length - 8;
+		status = 0;
+	} else
+		dev_dbg(&priv->spi->dev, "read %x..%x --> %d\n",
+			(unsigned)from, (unsigned)(from + len),
+			status);
+	return status;
+}
+
+/*
+ * Write to the DataFlash device.
+ *   to     : Start offset in flash device
+ *   len    : Amount to write
+ *   retlen : Amount of data actually written
+ *   buf    : Buffer containing the data
+ */
+static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len,
+				size_t * retlen, const u_char * buf)
+{
+	struct dataflash	*priv = mtd->priv;
+	struct spi_device	*spi = priv->spi;
+	struct spi_transfer	x[2] = { };
+	struct spi_message	msg;
+	unsigned int		pageaddr, addr, offset, writelen;
+	size_t			remaining = len;
+	u_char			*writebuf = (u_char *) buf;
+	int			status = -EINVAL;
+	u8			*command;
+
+	dev_dbg(&spi->dev, "write 0x%x..0x%x\n",
+		(unsigned int)to, (unsigned int)(to + len));
+
+	spi_message_init(&msg);
+
+	x[0].tx_buf = command = priv->command;
+	x[0].len = 4;
+	spi_message_add_tail(&x[0], &msg);
+
+	pageaddr = ((unsigned)to / priv->page_size);
+	offset = ((unsigned)to % priv->page_size);
+	if (offset + len > priv->page_size)
+		writelen = priv->page_size - offset;
+	else
+		writelen = len;
+
+	mutex_lock(&priv->lock);
+	while (remaining > 0) {
+		dev_dbg(&spi->dev, "write @ %i:%i len=%i\n",
+			pageaddr, offset, writelen);
+
+		/* REVISIT:
+		 * (a) each page in a sector must be rewritten at least
+		 *     once every 10K sibling erase/program operations.
+		 * (b) for pages that are already erased, we could
+		 *     use WRITE+MWRITE not PROGRAM for ~30% speedup.
+		 * (c) WRITE to buffer could be done while waiting for
+		 *     a previous MWRITE/MWERASE to complete ...
+		 * (d) error handling here seems to be mostly missing.
+		 *
+		 * Two persistent bits per page, plus a per-sector counter,
+		 * could support (a) and (b) ... we might consider using
+		 * the second half of sector zero, which is just one block,
+		 * to track that state.  (On AT91, that sector should also
+		 * support boot-from-DataFlash.)
+		 */
+
+		addr = pageaddr << priv->page_offset;
+
+		/* (1) Maybe transfer partial page to Buffer1 */
+		if (writelen != priv->page_size) {
+			command[0] = OP_TRANSFER_BUF1;
+			command[1] = (addr & 0x00FF0000) >> 16;
+			command[2] = (addr & 0x0000FF00) >> 8;
+			command[3] = 0;
+
+			dev_dbg(&spi->dev, "TRANSFER: (%x) %x %x %x\n",
+				command[0], command[1], command[2], command[3]);
+
+			status = spi_sync(spi, &msg);
+			if (status < 0)
+				dev_dbg(&spi->dev, "xfer %u -> %d\n",
+					addr, status);
+
+			(void) dataflash_waitready(priv->spi);
+		}
+
+		/* (2) Program full page via Buffer1 */
+		addr += offset;
+		command[0] = OP_PROGRAM_VIA_BUF1;
+		command[1] = (addr & 0x00FF0000) >> 16;
+		command[2] = (addr & 0x0000FF00) >> 8;
+		command[3] = (addr & 0x000000FF);
+
+		dev_dbg(&spi->dev, "PROGRAM: (%x) %x %x %x\n",
+			command[0], command[1], command[2], command[3]);
+
+		x[1].tx_buf = writebuf;
+		x[1].len = writelen;
+		spi_message_add_tail(x + 1, &msg);
+		status = spi_sync(spi, &msg);
+		spi_transfer_del(x + 1);
+		if (status < 0)
+			dev_dbg(&spi->dev, "pgm %u/%u -> %d\n",
+				addr, writelen, status);
+
+		(void) dataflash_waitready(priv->spi);
+
+
+#ifdef CONFIG_MTD_DATAFLASH_WRITE_VERIFY
+
+		/* (3) Compare to Buffer1 */
+		addr = pageaddr << priv->page_offset;
+		command[0] = OP_COMPARE_BUF1;
+		command[1] = (addr & 0x00FF0000) >> 16;
+		command[2] = (addr & 0x0000FF00) >> 8;
+		command[3] = 0;
+
+		dev_dbg(&spi->dev, "COMPARE: (%x) %x %x %x\n",
+			command[0], command[1], command[2], command[3]);
+
+		status = spi_sync(spi, &msg);
+		if (status < 0)
+			dev_dbg(&spi->dev, "compare %u -> %d\n",
+				addr, status);
+
+		status = dataflash_waitready(priv->spi);
+
+		/* Check result of the compare operation */
+		if (status & (1 << 6)) {
+			dev_err(&spi->dev, "compare page %u, err %d\n",
+				pageaddr, status);
+			remaining = 0;
+			status = -EIO;
+			break;
+		} else
+			status = 0;
+
+#endif	/* CONFIG_MTD_DATAFLASH_WRITE_VERIFY */
+
+		remaining = remaining - writelen;
+		pageaddr++;
+		offset = 0;
+		writebuf += writelen;
+		*retlen += writelen;
+
+		if (remaining > priv->page_size)
+			writelen = priv->page_size;
+		else
+			writelen = remaining;
+	}
+	mutex_unlock(&priv->lock);
+
+	return status;
+}
+
+/* ......................................................................... */
+
+#ifdef CONFIG_MTD_DATAFLASH_OTP
+
+static int dataflash_get_otp_info(struct mtd_info *mtd, size_t len,
+				  size_t *retlen, struct otp_info *info)
+{
+	/* Report both blocks as identical:  bytes 0..64, locked.
+	 * Unless the user block changed from all-ones, we can't
+	 * tell whether it's still writable; so we assume it isn't.
+	 */
+	info->start = 0;
+	info->length = 64;
+	info->locked = 1;
+	*retlen = sizeof(*info);
+	return 0;
+}
+
+static ssize_t otp_read(struct spi_device *spi, unsigned base,
+		u8 *buf, loff_t off, size_t len)
+{
+	struct spi_message	m;
+	size_t			l;
+	u8			*scratch;
+	struct spi_transfer	t;
+	int			status;
+
+	if (off > 64)
+		return -EINVAL;
+
+	if ((off + len) > 64)
+		len = 64 - off;
+
+	spi_message_init(&m);
+
+	l = 4 + base + off + len;
+	scratch = kzalloc(l, GFP_KERNEL);
+	if (!scratch)
+		return -ENOMEM;
+
+	/* OUT: OP_READ_SECURITY, 3 don't-care bytes, zeroes
+	 * IN:  ignore 4 bytes, data bytes 0..N (max 127)
+	 */
+	scratch[0] = OP_READ_SECURITY;
+
+	memset(&t, 0, sizeof t);
+	t.tx_buf = scratch;
+	t.rx_buf = scratch;
+	t.len = l;
+	spi_message_add_tail(&t, &m);
+
+	dataflash_waitready(spi);
+
+	status = spi_sync(spi, &m);
+	if (status >= 0) {
+		memcpy(buf, scratch + 4 + base + off, len);
+		status = len;
+	}
+
+	kfree(scratch);
+	return status;
+}
+
+static int dataflash_read_fact_otp(struct mtd_info *mtd,
+		loff_t from, size_t len, size_t *retlen, u_char *buf)
+{
+	struct dataflash	*priv = mtd->priv;
+	int			status;
+
+	/* 64 bytes, from 0..63 ... start at 64 on-chip */
+	mutex_lock(&priv->lock);
+	status = otp_read(priv->spi, 64, buf, from, len);
+	mutex_unlock(&priv->lock);
+
+	if (status < 0)
+		return status;
+	*retlen = status;
+	return 0;
+}
+
+static int dataflash_read_user_otp(struct mtd_info *mtd,
+		loff_t from, size_t len, size_t *retlen, u_char *buf)
+{
+	struct dataflash	*priv = mtd->priv;
+	int			status;
+
+	/* 64 bytes, from 0..63 ... start at 0 on-chip */
+	mutex_lock(&priv->lock);
+	status = otp_read(priv->spi, 0, buf, from, len);
+	mutex_unlock(&priv->lock);
+
+	if (status < 0)
+		return status;
+	*retlen = status;
+	return 0;
+}
+
+static int dataflash_write_user_otp(struct mtd_info *mtd,
+		loff_t from, size_t len, size_t *retlen, const u_char *buf)
+{
+	struct spi_message	m;
+	const size_t		l = 4 + 64;
+	u8			*scratch;
+	struct spi_transfer	t;
+	struct dataflash	*priv = mtd->priv;
+	int			status;
+
+	if (from >= 64) {
+		/*
+		 * Attempting to write beyond the end of OTP memory,
+		 * no data can be written.
+		 */
+		*retlen = 0;
+		return 0;
+	}
+
+	/* Truncate the write to fit into OTP memory. */
+	if ((from + len) > 64)
+		len = 64 - from;
+
+	/* OUT: OP_WRITE_SECURITY, 3 zeroes, 64 data-or-zero bytes
+	 * IN:  ignore all
+	 */
+	scratch = kzalloc(l, GFP_KERNEL);
+	if (!scratch)
+		return -ENOMEM;
+	scratch[0] = OP_WRITE_SECURITY;
+	memcpy(scratch + 4 + from, buf, len);
+
+	spi_message_init(&m);
+
+	memset(&t, 0, sizeof t);
+	t.tx_buf = scratch;
+	t.len = l;
+	spi_message_add_tail(&t, &m);
+
+	/* Write the OTP bits, if they've not yet been written.
+	 * This modifies SRAM buffer1.
+	 */
+	mutex_lock(&priv->lock);
+	dataflash_waitready(priv->spi);
+	status = spi_sync(priv->spi, &m);
+	mutex_unlock(&priv->lock);
+
+	kfree(scratch);
+
+	if (status >= 0) {
+		status = 0;
+		*retlen = len;
+	}
+	return status;
+}
+
+static char *otp_setup(struct mtd_info *device, char revision)
+{
+	device->_get_fact_prot_info = dataflash_get_otp_info;
+	device->_read_fact_prot_reg = dataflash_read_fact_otp;
+	device->_get_user_prot_info = dataflash_get_otp_info;
+	device->_read_user_prot_reg = dataflash_read_user_otp;
+
+	/* rev c parts (at45db321c and at45db1281 only!) use a
+	 * different write procedure; not (yet?) implemented.
+	 */
+	if (revision > 'c')
+		device->_write_user_prot_reg = dataflash_write_user_otp;
+
+	return ", OTP";
+}
+
+#else
+
+static char *otp_setup(struct mtd_info *device, char revision)
+{
+	return " (OTP)";
+}
+
+#endif
+
+/* ......................................................................... */
+
+/*
+ * Register DataFlash device with MTD subsystem.
+ */
+static int add_dataflash_otp(struct spi_device *spi, char *name, int nr_pages,
+			     int pagesize, int pageoffset, char revision)
+{
+	struct dataflash		*priv;
+	struct mtd_info			*device;
+	struct flash_platform_data	*pdata = dev_get_platdata(&spi->dev);
+	char				*otp_tag = "";
+	int				err = 0;
+
+	priv = kzalloc(sizeof *priv, GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	mutex_init(&priv->lock);
+	priv->spi = spi;
+	priv->page_size = pagesize;
+	priv->page_offset = pageoffset;
+
+	/* name must be usable with cmdlinepart */
+	sprintf(priv->name, "spi%d.%d-%s",
+			spi->master->bus_num, spi->chip_select,
+			name);
+
+	device = &priv->mtd;
+	device->name = (pdata && pdata->name) ? pdata->name : priv->name;
+	device->size = nr_pages * pagesize;
+	device->erasesize = pagesize;
+	device->writesize = pagesize;
+	device->type = MTD_DATAFLASH;
+	device->flags = MTD_WRITEABLE;
+	device->_erase = dataflash_erase;
+	device->_read = dataflash_read;
+	device->_write = dataflash_write;
+	device->priv = priv;
+
+	device->dev.parent = &spi->dev;
+	mtd_set_of_node(device, spi->dev.of_node);
+
+	if (revision >= 'c')
+		otp_tag = otp_setup(device, revision);
+
+	dev_info(&spi->dev, "%s (%lld KBytes) pagesize %d bytes%s\n",
+			name, (long long)((device->size + 1023) >> 10),
+			pagesize, otp_tag);
+	spi_set_drvdata(spi, priv);
+
+	err = mtd_device_register(device,
+			pdata ? pdata->parts : NULL,
+			pdata ? pdata->nr_parts : 0);
+
+	if (!err)
+		return 0;
+
+	kfree(priv);
+	return err;
+}
+
+static inline int add_dataflash(struct spi_device *spi, char *name,
+				int nr_pages, int pagesize, int pageoffset)
+{
+	return add_dataflash_otp(spi, name, nr_pages, pagesize,
+			pageoffset, 0);
+}
+
+struct flash_info {
+	char		*name;
+
+	/* JEDEC id has a high byte of zero plus three data bytes:
+	 * the manufacturer id, then a two byte device id.
+	 */
+	u64		jedec_id;
+
+	/* The size listed here is what works with OP_ERASE_PAGE. */
+	unsigned	nr_pages;
+	u16		pagesize;
+	u16		pageoffset;
+
+	u16		flags;
+#define SUP_EXTID	0x0004		/* supports extended ID data */
+#define SUP_POW2PS	0x0002		/* supports 2^N byte pages */
+#define IS_POW2PS	0x0001		/* uses 2^N byte pages */
+};
+
+static struct flash_info dataflash_data[] = {
+
+	/*
+	 * NOTE:  chips with SUP_POW2PS (rev D and up) need two entries,
+	 * one with IS_POW2PS and the other without.  The entry with the
+	 * non-2^N byte page size can't name exact chip revisions without
+	 * losing backwards compatibility for cmdlinepart.
+	 *
+	 * These newer chips also support 128-byte security registers (with
+	 * 64 bytes one-time-programmable) and software write-protection.
+	 */
+	{ "AT45DB011B",  0x1f2200, 512, 264, 9, SUP_POW2PS},
+	{ "at45db011d",  0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB021B",  0x1f2300, 1024, 264, 9, SUP_POW2PS},
+	{ "at45db021d",  0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB041x",  0x1f2400, 2048, 264, 9, SUP_POW2PS},
+	{ "at45db041d",  0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB081B",  0x1f2500, 4096, 264, 9, SUP_POW2PS},
+	{ "at45db081d",  0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB161x",  0x1f2600, 4096, 528, 10, SUP_POW2PS},
+	{ "at45db161d",  0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB321x",  0x1f2700, 8192, 528, 10, 0},		/* rev C */
+
+	{ "AT45DB321x",  0x1f2701, 8192, 528, 10, SUP_POW2PS},
+	{ "at45db321d",  0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB642x",  0x1f2800, 8192, 1056, 11, SUP_POW2PS},
+	{ "at45db642d",  0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
+
+	{ "AT45DB641E",  0x1f28000100ULL, 32768, 264, 9, SUP_EXTID | SUP_POW2PS},
+	{ "at45db641e",  0x1f28000100ULL, 32768, 256, 8, SUP_EXTID | SUP_POW2PS | IS_POW2PS},
+};
+
+static struct flash_info *jedec_lookup(struct spi_device *spi,
+				       u64 jedec, bool use_extid)
+{
+	struct flash_info *info;
+	int status;
+
+	for (info = dataflash_data;
+	     info < dataflash_data + ARRAY_SIZE(dataflash_data);
+	     info++) {
+		if (use_extid && !(info->flags & SUP_EXTID))
+			continue;
+
+		if (info->jedec_id == jedec) {
+			dev_dbg(&spi->dev, "OTP, sector protect%s\n",
+				(info->flags & SUP_POW2PS) ?
+				", binary pagesize" : "");
+			if (info->flags & SUP_POW2PS) {
+				status = dataflash_status(spi);
+				if (status < 0) {
+					dev_dbg(&spi->dev, "status error %d\n",
+						status);
+					return ERR_PTR(status);
+				}
+				if (status & 0x1) {
+					if (info->flags & IS_POW2PS)
+						return info;
+				} else {
+					if (!(info->flags & IS_POW2PS))
+						return info;
+				}
+			} else
+				return info;
+		}
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+
+static struct flash_info *jedec_probe(struct spi_device *spi)
+{
+	int ret;
+	u8 code = OP_READ_ID;
+	u64 jedec;
+	u8 id[sizeof(jedec)] = {0};
+	const unsigned int id_size = 5;
+	struct flash_info *info;
+
+	/*
+	 * JEDEC also defines an optional "extended device information"
+	 * string for after vendor-specific data, after the three bytes
+	 * we use here.  Supporting some chips might require using it.
+	 *
+	 * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
+	 * That's not an error; only rev C and newer chips handle it, and
+	 * only Atmel sells these chips.
+	 */
+	ret = spi_write_then_read(spi, &code, 1, id, id_size);
+	if (ret < 0) {
+		dev_dbg(&spi->dev, "error %d reading JEDEC ID\n", ret);
+		return ERR_PTR(ret);
+	}
+
+	if (id[0] != CFI_MFR_ATMEL)
+		return NULL;
+
+	jedec = be64_to_cpup((__be64 *)id);
+
+	/*
+	 * First, try to match device using extended device
+	 * information
+	 */
+	info = jedec_lookup(spi, jedec >> DATAFLASH_SHIFT_EXTID, true);
+	if (!IS_ERR(info))
+		return info;
+	/*
+	 * If that fails, make another pass using regular ID
+	 * information
+	 */
+	info = jedec_lookup(spi, jedec >> DATAFLASH_SHIFT_ID, false);
+	if (!IS_ERR(info))
+		return info;
+	/*
+	 * Treat other chips as errors ... we won't know the right page
+	 * size (it might be binary) even when we can tell which density
+	 * class is involved (legacy chip id scheme).
+	 */
+	dev_warn(&spi->dev, "JEDEC id %016llx not handled\n", jedec);
+	return ERR_PTR(-ENODEV);
+}
+
+/*
+ * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
+ * or else the ID code embedded in the status bits:
+ *
+ *   Device      Density         ID code          #Pages PageSize  Offset
+ *   AT45DB011B  1Mbit   (128K)  xx0011xx (0x0c)    512    264      9
+ *   AT45DB021B  2Mbit   (256K)  xx0101xx (0x14)   1024    264      9
+ *   AT45DB041B  4Mbit   (512K)  xx0111xx (0x1c)   2048    264      9
+ *   AT45DB081B  8Mbit   (1M)    xx1001xx (0x24)   4096    264      9
+ *   AT45DB0161B 16Mbit  (2M)    xx1011xx (0x2c)   4096    528     10
+ *   AT45DB0321B 32Mbit  (4M)    xx1101xx (0x34)   8192    528     10
+ *   AT45DB0642  64Mbit  (8M)    xx111xxx (0x3c)   8192   1056     11
+ *   AT45DB1282  128Mbit (16M)   xx0100xx (0x10)  16384   1056     11
+ */
+static int dataflash_probe(struct spi_device *spi)
+{
+	int status;
+	struct flash_info	*info;
+
+	/*
+	 * Try to detect dataflash by JEDEC ID.
+	 * If it succeeds we know we have either a C or D part.
+	 * D will support power of 2 pagesize option.
+	 * Both support the security register, though with different
+	 * write procedures.
+	 */
+	info = jedec_probe(spi);
+	if (IS_ERR(info))
+		return PTR_ERR(info);
+	if (info != NULL)
+		return add_dataflash_otp(spi, info->name, info->nr_pages,
+				info->pagesize, info->pageoffset,
+				(info->flags & SUP_POW2PS) ? 'd' : 'c');
+
+	/*
+	 * Older chips support only legacy commands, identifing
+	 * capacity using bits in the status byte.
+	 */
+	status = dataflash_status(spi);
+	if (status <= 0 || status == 0xff) {
+		dev_dbg(&spi->dev, "status error %d\n", status);
+		if (status == 0 || status == 0xff)
+			status = -ENODEV;
+		return status;
+	}
+
+	/* if there's a device there, assume it's dataflash.
+	 * board setup should have set spi->max_speed_max to
+	 * match f(car) for continuous reads, mode 0 or 3.
+	 */
+	switch (status & 0x3c) {
+	case 0x0c:	/* 0 0 1 1 x x */
+		status = add_dataflash(spi, "AT45DB011B", 512, 264, 9);
+		break;
+	case 0x14:	/* 0 1 0 1 x x */
+		status = add_dataflash(spi, "AT45DB021B", 1024, 264, 9);
+		break;
+	case 0x1c:	/* 0 1 1 1 x x */
+		status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9);
+		break;
+	case 0x24:	/* 1 0 0 1 x x */
+		status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9);
+		break;
+	case 0x2c:	/* 1 0 1 1 x x */
+		status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10);
+		break;
+	case 0x34:	/* 1 1 0 1 x x */
+		status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10);
+		break;
+	case 0x38:	/* 1 1 1 x x x */
+	case 0x3c:
+		status = add_dataflash(spi, "AT45DB642x", 8192, 1056, 11);
+		break;
+	/* obsolete AT45DB1282 not (yet?) supported */
+	default:
+		dev_info(&spi->dev, "unsupported device (%x)\n",
+				status & 0x3c);
+		status = -ENODEV;
+	}
+
+	if (status < 0)
+		dev_dbg(&spi->dev, "add_dataflash --> %d\n", status);
+
+	return status;
+}
+
+static void dataflash_remove(struct spi_device *spi)
+{
+	struct dataflash	*flash = spi_get_drvdata(spi);
+
+	dev_dbg(&spi->dev, "remove\n");
+
+	WARN_ON(mtd_device_unregister(&flash->mtd));
+
+	kfree(flash);
+}
+
+static struct spi_driver dataflash_driver = {
+	.driver = {
+		.name		= "mtd_dataflash",
+		.of_match_table = of_match_ptr(dataflash_dt_ids),
+	},
+	.id_table = dataflash_dev_ids,
+
+	.probe		= dataflash_probe,
+	.remove		= dataflash_remove,
+	.id_table	= dataflash_spi_ids,
+
+	/* FIXME:  investigate suspend and resume... */
+};
+
+module_spi_driver(dataflash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andrew Victor, David Brownell");
+MODULE_DESCRIPTION("MTD DataFlash driver");
+MODULE_ALIAS("spi:mtd_dataflash");