Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 268 insertions, 0 deletions

diff --git a/drivers/mtd/nand/raw/xway_nand.c b/drivers/mtd/nand/raw/xway_nand.c
new file mode 100644
index 000000000..035b82aa2
--- /dev/null
+++ b/drivers/mtd/nand/raw/xway_nand.c
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright © 2012 John Crispin <john@phrozen.org>
+ *  Copyright © 2016 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/mtd/rawnand.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+
+#include <lantiq_soc.h>
+
+/* nand registers */
+#define EBU_ADDSEL1		0x24
+#define EBU_NAND_CON		0xB0
+#define EBU_NAND_WAIT		0xB4
+#define  NAND_WAIT_RD		BIT(0) /* NAND flash status output */
+#define  NAND_WAIT_WR_C		BIT(3) /* NAND Write/Read complete */
+#define EBU_NAND_ECC0		0xB8
+#define EBU_NAND_ECC_AC		0xBC
+
+/*
+ * nand commands
+ * The pins of the NAND chip are selected based on the address bits of the
+ * "register" read and write. There are no special registers, but an
+ * address range and the lower address bits are used to activate the
+ * correct line. For example when the bit (1 << 2) is set in the address
+ * the ALE pin will be activated.
+ */
+#define NAND_CMD_ALE		BIT(2) /* address latch enable */
+#define NAND_CMD_CLE		BIT(3) /* command latch enable */
+#define NAND_CMD_CS		BIT(4) /* chip select */
+#define NAND_CMD_SE		BIT(5) /* spare area access latch */
+#define NAND_CMD_WP		BIT(6) /* write protect */
+#define NAND_WRITE_CMD		(NAND_CMD_CS | NAND_CMD_CLE)
+#define NAND_WRITE_ADDR		(NAND_CMD_CS | NAND_CMD_ALE)
+#define NAND_WRITE_DATA		(NAND_CMD_CS)
+#define NAND_READ_DATA		(NAND_CMD_CS)
+
+/* we need to tel the ebu which addr we mapped the nand to */
+#define ADDSEL1_MASK(x)		(x << 4)
+#define ADDSEL1_REGEN		1
+
+/* we need to tell the EBU that we have nand attached and set it up properly */
+#define BUSCON1_SETUP		(1 << 22)
+#define BUSCON1_BCGEN_RES	(0x3 << 12)
+#define BUSCON1_WAITWRC2	(2 << 8)
+#define BUSCON1_WAITRDC2	(2 << 6)
+#define BUSCON1_HOLDC1		(1 << 4)
+#define BUSCON1_RECOVC1		(1 << 2)
+#define BUSCON1_CMULT4		1
+
+#define NAND_CON_CE		(1 << 20)
+#define NAND_CON_OUT_CS1	(1 << 10)
+#define NAND_CON_IN_CS1		(1 << 8)
+#define NAND_CON_PRE_P		(1 << 7)
+#define NAND_CON_WP_P		(1 << 6)
+#define NAND_CON_SE_P		(1 << 5)
+#define NAND_CON_CS_P		(1 << 4)
+#define NAND_CON_CSMUX		(1 << 1)
+#define NAND_CON_NANDM		1
+
+struct xway_nand_data {
+	struct nand_controller	controller;
+	struct nand_chip	chip;
+	unsigned long		csflags;
+	void __iomem		*nandaddr;
+};
+
+static u8 xway_readb(struct mtd_info *mtd, int op)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct xway_nand_data *data = nand_get_controller_data(chip);
+
+	return readb(data->nandaddr + op);
+}
+
+static void xway_writeb(struct mtd_info *mtd, int op, u8 value)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct xway_nand_data *data = nand_get_controller_data(chip);
+
+	writeb(value, data->nandaddr + op);
+}
+
+static void xway_select_chip(struct nand_chip *chip, int select)
+{
+	struct xway_nand_data *data = nand_get_controller_data(chip);
+
+	switch (select) {
+	case -1:
+		ltq_ebu_w32_mask(NAND_CON_CE, 0, EBU_NAND_CON);
+		ltq_ebu_w32_mask(NAND_CON_NANDM, 0, EBU_NAND_CON);
+		spin_unlock_irqrestore(&ebu_lock, data->csflags);
+		break;
+	case 0:
+		spin_lock_irqsave(&ebu_lock, data->csflags);
+		ltq_ebu_w32_mask(0, NAND_CON_NANDM, EBU_NAND_CON);
+		ltq_ebu_w32_mask(0, NAND_CON_CE, EBU_NAND_CON);
+		break;
+	default:
+		BUG();
+	}
+}
+
+static void xway_cmd_ctrl(struct nand_chip *chip, int cmd, unsigned int ctrl)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	if (ctrl & NAND_CLE)
+		xway_writeb(mtd, NAND_WRITE_CMD, cmd);
+	else if (ctrl & NAND_ALE)
+		xway_writeb(mtd, NAND_WRITE_ADDR, cmd);
+
+	while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0)
+		;
+}
+
+static int xway_dev_ready(struct nand_chip *chip)
+{
+	return ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_RD;
+}
+
+static unsigned char xway_read_byte(struct nand_chip *chip)
+{
+	return xway_readb(nand_to_mtd(chip), NAND_READ_DATA);
+}
+
+static void xway_read_buf(struct nand_chip *chip, u_char *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		buf[i] = xway_readb(nand_to_mtd(chip), NAND_WRITE_DATA);
+}
+
+static void xway_write_buf(struct nand_chip *chip, const u_char *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		xway_writeb(nand_to_mtd(chip), NAND_WRITE_DATA, buf[i]);
+}
+
+static int xway_attach_chip(struct nand_chip *chip)
+{
+	if (chip->ecc.engine_type == NAND_ECC_ENGINE_TYPE_SOFT &&
+	    chip->ecc.algo == NAND_ECC_ALGO_UNKNOWN)
+		chip->ecc.algo = NAND_ECC_ALGO_HAMMING;
+
+	return 0;
+}
+
+static const struct nand_controller_ops xway_nand_ops = {
+	.attach_chip = xway_attach_chip,
+};
+
+/*
+ * Probe for the NAND device.
+ */
+static int xway_nand_probe(struct platform_device *pdev)
+{
+	struct xway_nand_data *data;
+	struct mtd_info *mtd;
+	int err;
+	u32 cs;
+	u32 cs_flag = 0;
+
+	/* Allocate memory for the device structure (and zero it) */
+	data = devm_kzalloc(&pdev->dev, sizeof(struct xway_nand_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->nandaddr = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(data->nandaddr))
+		return PTR_ERR(data->nandaddr);
+
+	nand_set_flash_node(&data->chip, pdev->dev.of_node);
+	mtd = nand_to_mtd(&data->chip);
+	mtd->dev.parent = &pdev->dev;
+
+	data->chip.legacy.cmd_ctrl = xway_cmd_ctrl;
+	data->chip.legacy.dev_ready = xway_dev_ready;
+	data->chip.legacy.select_chip = xway_select_chip;
+	data->chip.legacy.write_buf = xway_write_buf;
+	data->chip.legacy.read_buf = xway_read_buf;
+	data->chip.legacy.read_byte = xway_read_byte;
+	data->chip.legacy.chip_delay = 30;
+
+	nand_controller_init(&data->controller);
+	data->controller.ops = &xway_nand_ops;
+	data->chip.controller = &data->controller;
+
+	platform_set_drvdata(pdev, data);
+	nand_set_controller_data(&data->chip, data);
+
+	/* load our CS from the DT. Either we find a valid 1 or default to 0 */
+	err = of_property_read_u32(pdev->dev.of_node, "lantiq,cs", &cs);
+	if (!err && cs == 1)
+		cs_flag = NAND_CON_IN_CS1 | NAND_CON_OUT_CS1;
+
+	/* setup the EBU to run in NAND mode on our base addr */
+	ltq_ebu_w32(CPHYSADDR(data->nandaddr)
+		    | ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1);
+
+	ltq_ebu_w32(BUSCON1_SETUP | BUSCON1_BCGEN_RES | BUSCON1_WAITWRC2
+		    | BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1
+		    | BUSCON1_CMULT4, LTQ_EBU_BUSCON1);
+
+	ltq_ebu_w32(NAND_CON_NANDM | NAND_CON_CSMUX | NAND_CON_CS_P
+		    | NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
+		    | cs_flag, EBU_NAND_CON);
+
+	/*
+	 * This driver assumes that the default ECC engine should be TYPE_SOFT.
+	 * Set ->engine_type before registering the NAND devices in order to
+	 * provide a driver specific default value.
+	 */
+	data->chip.ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+
+	/* Scan to find existence of the device */
+	err = nand_scan(&data->chip, 1);
+	if (err)
+		return err;
+
+	err = mtd_device_register(mtd, NULL, 0);
+	if (err)
+		nand_cleanup(&data->chip);
+
+	return err;
+}
+
+/*
+ * Remove a NAND device.
+ */
+static int xway_nand_remove(struct platform_device *pdev)
+{
+	struct xway_nand_data *data = platform_get_drvdata(pdev);
+	struct nand_chip *chip = &data->chip;
+	int ret;
+
+	ret = mtd_device_unregister(nand_to_mtd(chip));
+	WARN_ON(ret);
+	nand_cleanup(chip);
+
+	return 0;
+}
+
+static const struct of_device_id xway_nand_match[] = {
+	{ .compatible = "lantiq,nand-xway" },
+	{},
+};
+
+static struct platform_driver xway_nand_driver = {
+	.probe	= xway_nand_probe,
+	.remove	= xway_nand_remove,
+	.driver	= {
+		.name		= "lantiq,nand-xway",
+		.of_match_table = xway_nand_match,
+	},
+};
+
+builtin_platform_driver(xway_nand_driver);