Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1344 insertions, 0 deletions

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
new file mode 100644
index 000000000..f83447259
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -0,0 +1,1344 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer
+ *
+ * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mdio-mux.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+/* General notes on dwmac-sun8i:
+ * Locking: no locking is necessary in this file because all necessary locking
+ *		is done in the "stmmac files"
+ */
+
+/* struct emac_variant - Describe dwmac-sun8i hardware variant
+ * @default_syscon_value:	The default value of the EMAC register in syscon
+ *				This value is used for disabling properly EMAC
+ *				and used as a good starting value in case of the
+ *				boot process(uboot) leave some stuff.
+ * @syscon_field		reg_field for the syscon's gmac register
+ * @soc_has_internal_phy:	Does the MAC embed an internal PHY
+ * @support_mii:		Does the MAC handle MII
+ * @support_rmii:		Does the MAC handle RMII
+ * @support_rgmii:		Does the MAC handle RGMII
+ *
+ * @rx_delay_max:		Maximum raw value for RX delay chain
+ * @tx_delay_max:		Maximum raw value for TX delay chain
+ *				These two also indicate the bitmask for
+ *				the RX and TX delay chain registers. A
+ *				value of zero indicates this is not supported.
+ */
+struct emac_variant {
+	u32 default_syscon_value;
+	const struct reg_field *syscon_field;
+	bool soc_has_internal_phy;
+	bool support_mii;
+	bool support_rmii;
+	bool support_rgmii;
+	u8 rx_delay_max;
+	u8 tx_delay_max;
+};
+
+/* struct sunxi_priv_data - hold all sunxi private data
+ * @ephy_clk:	reference to the optional EPHY clock for the internal PHY
+ * @regulator:	reference to the optional regulator
+ * @rst_ephy:	reference to the optional EPHY reset for the internal PHY
+ * @variant:	reference to the current board variant
+ * @regmap:	regmap for using the syscon
+ * @internal_phy_powered: Does the internal PHY is enabled
+ * @use_internal_phy: Is the internal PHY selected for use
+ * @mux_handle:	Internal pointer used by mdio-mux lib
+ */
+struct sunxi_priv_data {
+	struct clk *ephy_clk;
+	struct regulator *regulator;
+	struct reset_control *rst_ephy;
+	const struct emac_variant *variant;
+	struct regmap_field *regmap_field;
+	bool internal_phy_powered;
+	bool use_internal_phy;
+	void *mux_handle;
+};
+
+/* EMAC clock register @ 0x30 in the "system control" address range */
+static const struct reg_field sun8i_syscon_reg_field = {
+	.reg = 0x30,
+	.lsb = 0,
+	.msb = 31,
+};
+
+/* EMAC clock register @ 0x164 in the CCU address range */
+static const struct reg_field sun8i_ccu_reg_field = {
+	.reg = 0x164,
+	.lsb = 0,
+	.msb = 31,
+};
+
+static const struct emac_variant emac_variant_h3 = {
+	.default_syscon_value = 0x58000,
+	.syscon_field = &sun8i_syscon_reg_field,
+	.soc_has_internal_phy = true,
+	.support_mii = true,
+	.support_rmii = true,
+	.support_rgmii = true,
+	.rx_delay_max = 31,
+	.tx_delay_max = 7,
+};
+
+static const struct emac_variant emac_variant_v3s = {
+	.default_syscon_value = 0x38000,
+	.syscon_field = &sun8i_syscon_reg_field,
+	.soc_has_internal_phy = true,
+	.support_mii = true
+};
+
+static const struct emac_variant emac_variant_a83t = {
+	.default_syscon_value = 0,
+	.syscon_field = &sun8i_syscon_reg_field,
+	.soc_has_internal_phy = false,
+	.support_mii = true,
+	.support_rgmii = true,
+	.rx_delay_max = 31,
+	.tx_delay_max = 7,
+};
+
+static const struct emac_variant emac_variant_r40 = {
+	.default_syscon_value = 0,
+	.syscon_field = &sun8i_ccu_reg_field,
+	.support_mii = true,
+	.support_rgmii = true,
+	.rx_delay_max = 7,
+};
+
+static const struct emac_variant emac_variant_a64 = {
+	.default_syscon_value = 0,
+	.syscon_field = &sun8i_syscon_reg_field,
+	.soc_has_internal_phy = false,
+	.support_mii = true,
+	.support_rmii = true,
+	.support_rgmii = true,
+	.rx_delay_max = 31,
+	.tx_delay_max = 7,
+};
+
+static const struct emac_variant emac_variant_h6 = {
+	.default_syscon_value = 0x50000,
+	.syscon_field = &sun8i_syscon_reg_field,
+	/* The "Internal PHY" of H6 is not on the die. It's on the
+	 * co-packaged AC200 chip instead.
+	 */
+	.soc_has_internal_phy = false,
+	.support_mii = true,
+	.support_rmii = true,
+	.support_rgmii = true,
+	.rx_delay_max = 31,
+	.tx_delay_max = 7,
+};
+
+#define EMAC_BASIC_CTL0 0x00
+#define EMAC_BASIC_CTL1 0x04
+#define EMAC_INT_STA    0x08
+#define EMAC_INT_EN     0x0C
+#define EMAC_TX_CTL0    0x10
+#define EMAC_TX_CTL1    0x14
+#define EMAC_TX_FLOW_CTL        0x1C
+#define EMAC_TX_DESC_LIST 0x20
+#define EMAC_RX_CTL0    0x24
+#define EMAC_RX_CTL1    0x28
+#define EMAC_RX_DESC_LIST 0x34
+#define EMAC_RX_FRM_FLT 0x38
+#define EMAC_MDIO_CMD   0x48
+#define EMAC_MDIO_DATA  0x4C
+#define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8)
+#define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8)
+#define EMAC_TX_DMA_STA 0xB0
+#define EMAC_TX_CUR_DESC        0xB4
+#define EMAC_TX_CUR_BUF 0xB8
+#define EMAC_RX_DMA_STA 0xC0
+#define EMAC_RX_CUR_DESC        0xC4
+#define EMAC_RX_CUR_BUF 0xC8
+
+/* Use in EMAC_BASIC_CTL0 */
+#define EMAC_DUPLEX_FULL	BIT(0)
+#define EMAC_LOOPBACK		BIT(1)
+#define EMAC_SPEED_1000 0
+#define EMAC_SPEED_100 (0x03 << 2)
+#define EMAC_SPEED_10 (0x02 << 2)
+
+/* Use in EMAC_BASIC_CTL1 */
+#define EMAC_BURSTLEN_SHIFT		24
+
+/* Used in EMAC_RX_FRM_FLT */
+#define EMAC_FRM_FLT_RXALL              BIT(0)
+#define EMAC_FRM_FLT_CTL                BIT(13)
+#define EMAC_FRM_FLT_MULTICAST          BIT(16)
+
+/* Used in RX_CTL1*/
+#define EMAC_RX_MD              BIT(1)
+#define EMAC_RX_TH_MASK		GENMASK(5, 4)
+#define EMAC_RX_TH_32		0
+#define EMAC_RX_TH_64		(0x1 << 4)
+#define EMAC_RX_TH_96		(0x2 << 4)
+#define EMAC_RX_TH_128		(0x3 << 4)
+#define EMAC_RX_DMA_EN  BIT(30)
+#define EMAC_RX_DMA_START       BIT(31)
+
+/* Used in TX_CTL1*/
+#define EMAC_TX_MD              BIT(1)
+#define EMAC_TX_NEXT_FRM        BIT(2)
+#define EMAC_TX_TH_MASK		GENMASK(10, 8)
+#define EMAC_TX_TH_64		0
+#define EMAC_TX_TH_128		(0x1 << 8)
+#define EMAC_TX_TH_192		(0x2 << 8)
+#define EMAC_TX_TH_256		(0x3 << 8)
+#define EMAC_TX_DMA_EN  BIT(30)
+#define EMAC_TX_DMA_START       BIT(31)
+
+/* Used in RX_CTL0 */
+#define EMAC_RX_RECEIVER_EN             BIT(31)
+#define EMAC_RX_DO_CRC BIT(27)
+#define EMAC_RX_FLOW_CTL_EN             BIT(16)
+
+/* Used in TX_CTL0 */
+#define EMAC_TX_TRANSMITTER_EN  BIT(31)
+
+/* Used in EMAC_TX_FLOW_CTL */
+#define EMAC_TX_FLOW_CTL_EN             BIT(0)
+
+/* Used in EMAC_INT_STA */
+#define EMAC_TX_INT             BIT(0)
+#define EMAC_TX_DMA_STOP_INT    BIT(1)
+#define EMAC_TX_BUF_UA_INT      BIT(2)
+#define EMAC_TX_TIMEOUT_INT     BIT(3)
+#define EMAC_TX_UNDERFLOW_INT   BIT(4)
+#define EMAC_TX_EARLY_INT       BIT(5)
+#define EMAC_RX_INT             BIT(8)
+#define EMAC_RX_BUF_UA_INT      BIT(9)
+#define EMAC_RX_DMA_STOP_INT    BIT(10)
+#define EMAC_RX_TIMEOUT_INT     BIT(11)
+#define EMAC_RX_OVERFLOW_INT    BIT(12)
+#define EMAC_RX_EARLY_INT       BIT(13)
+#define EMAC_RGMII_STA_INT      BIT(16)
+
+#define EMAC_INT_MSK_COMMON	EMAC_RGMII_STA_INT
+#define EMAC_INT_MSK_TX		(EMAC_TX_INT | \
+				 EMAC_TX_DMA_STOP_INT | \
+				 EMAC_TX_BUF_UA_INT | \
+				 EMAC_TX_TIMEOUT_INT | \
+				 EMAC_TX_UNDERFLOW_INT | \
+				 EMAC_TX_EARLY_INT |\
+				 EMAC_INT_MSK_COMMON)
+#define EMAC_INT_MSK_RX		(EMAC_RX_INT | \
+				 EMAC_RX_BUF_UA_INT | \
+				 EMAC_RX_DMA_STOP_INT | \
+				 EMAC_RX_TIMEOUT_INT | \
+				 EMAC_RX_OVERFLOW_INT | \
+				 EMAC_RX_EARLY_INT | \
+				 EMAC_INT_MSK_COMMON)
+
+#define MAC_ADDR_TYPE_DST BIT(31)
+
+/* H3 specific bits for EPHY */
+#define H3_EPHY_ADDR_SHIFT	20
+#define H3_EPHY_CLK_SEL		BIT(18) /* 1: 24MHz, 0: 25MHz */
+#define H3_EPHY_LED_POL		BIT(17) /* 1: active low, 0: active high */
+#define H3_EPHY_SHUTDOWN	BIT(16) /* 1: shutdown, 0: power up */
+#define H3_EPHY_SELECT		BIT(15) /* 1: internal PHY, 0: external PHY */
+#define H3_EPHY_MUX_MASK	(H3_EPHY_SHUTDOWN | H3_EPHY_SELECT)
+#define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID	1
+#define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID	2
+
+/* H3/A64 specific bits */
+#define SYSCON_RMII_EN		BIT(13) /* 1: enable RMII (overrides EPIT) */
+
+/* Generic system control EMAC_CLK bits */
+#define SYSCON_ETXDC_SHIFT		10
+#define SYSCON_ERXDC_SHIFT		5
+/* EMAC PHY Interface Type */
+#define SYSCON_EPIT			BIT(2) /* 1: RGMII, 0: MII */
+#define SYSCON_ETCS_MASK		GENMASK(1, 0)
+#define SYSCON_ETCS_MII		0x0
+#define SYSCON_ETCS_EXT_GMII	0x1
+#define SYSCON_ETCS_INT_GMII	0x2
+
+/* sun8i_dwmac_dma_reset() - reset the EMAC
+ * Called from stmmac via stmmac_dma_ops->reset
+ */
+static int sun8i_dwmac_dma_reset(void __iomem *ioaddr)
+{
+	writel(0, ioaddr + EMAC_RX_CTL1);
+	writel(0, ioaddr + EMAC_TX_CTL1);
+	writel(0, ioaddr + EMAC_RX_FRM_FLT);
+	writel(0, ioaddr + EMAC_RX_DESC_LIST);
+	writel(0, ioaddr + EMAC_TX_DESC_LIST);
+	writel(0, ioaddr + EMAC_INT_EN);
+	writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+	return 0;
+}
+
+/* sun8i_dwmac_dma_init() - initialize the EMAC
+ * Called from stmmac via stmmac_dma_ops->init
+ */
+static void sun8i_dwmac_dma_init(void __iomem *ioaddr,
+				 struct stmmac_dma_cfg *dma_cfg, int atds)
+{
+	writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN);
+	writel(0x1FFFFFF, ioaddr + EMAC_INT_STA);
+}
+
+static void sun8i_dwmac_dma_init_rx(void __iomem *ioaddr,
+				    struct stmmac_dma_cfg *dma_cfg,
+				    dma_addr_t dma_rx_phy, u32 chan)
+{
+	/* Write RX descriptors address */
+	writel(lower_32_bits(dma_rx_phy), ioaddr + EMAC_RX_DESC_LIST);
+}
+
+static void sun8i_dwmac_dma_init_tx(void __iomem *ioaddr,
+				    struct stmmac_dma_cfg *dma_cfg,
+				    dma_addr_t dma_tx_phy, u32 chan)
+{
+	/* Write TX descriptors address */
+	writel(lower_32_bits(dma_tx_phy), ioaddr + EMAC_TX_DESC_LIST);
+}
+
+/* sun8i_dwmac_dump_regs() - Dump EMAC address space
+ * Called from stmmac_dma_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_regs(void __iomem *ioaddr, u32 *reg_space)
+{
+	int i;
+
+	for (i = 0; i < 0xC8; i += 4) {
+		if (i == 0x32 || i == 0x3C)
+			continue;
+		reg_space[i / 4] = readl(ioaddr + i);
+	}
+}
+
+/* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space
+ * Called from stmmac_ops->dump_regs
+ * Used for ethtool
+ */
+static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw,
+				      u32 *reg_space)
+{
+	int i;
+	void __iomem *ioaddr = hw->pcsr;
+
+	for (i = 0; i < 0xC8; i += 4) {
+		if (i == 0x32 || i == 0x3C)
+			continue;
+		reg_space[i / 4] = readl(ioaddr + i);
+	}
+}
+
+static void sun8i_dwmac_enable_dma_irq(void __iomem *ioaddr, u32 chan,
+				       bool rx, bool tx)
+{
+	u32 value = readl(ioaddr + EMAC_INT_EN);
+
+	if (rx)
+		value |= EMAC_RX_INT;
+	if (tx)
+		value |= EMAC_TX_INT;
+
+	writel(value, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_disable_dma_irq(void __iomem *ioaddr, u32 chan,
+					bool rx, bool tx)
+{
+	u32 value = readl(ioaddr + EMAC_INT_EN);
+
+	if (rx)
+		value &= ~EMAC_RX_INT;
+	if (tx)
+		value &= ~EMAC_TX_INT;
+
+	writel(value, ioaddr + EMAC_INT_EN);
+}
+
+static void sun8i_dwmac_dma_start_tx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v |= EMAC_TX_DMA_START;
+	v |= EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v |= EMAC_TX_DMA_START;
+	v |= EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_tx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	v &= ~EMAC_TX_DMA_EN;
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static void sun8i_dwmac_dma_start_rx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	v |= EMAC_RX_DMA_START;
+	v |= EMAC_RX_DMA_EN;
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static void sun8i_dwmac_dma_stop_rx(void __iomem *ioaddr, u32 chan)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	v &= ~EMAC_RX_DMA_EN;
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static int sun8i_dwmac_dma_interrupt(void __iomem *ioaddr,
+				     struct stmmac_extra_stats *x, u32 chan,
+				     u32 dir)
+{
+	u32 v;
+	int ret = 0;
+
+	v = readl(ioaddr + EMAC_INT_STA);
+
+	if (dir == DMA_DIR_RX)
+		v &= EMAC_INT_MSK_RX;
+	else if (dir == DMA_DIR_TX)
+		v &= EMAC_INT_MSK_TX;
+
+	if (v & EMAC_TX_INT) {
+		ret |= handle_tx;
+		x->tx_normal_irq_n++;
+	}
+
+	if (v & EMAC_TX_DMA_STOP_INT)
+		x->tx_process_stopped_irq++;
+
+	if (v & EMAC_TX_BUF_UA_INT)
+		x->tx_process_stopped_irq++;
+
+	if (v & EMAC_TX_TIMEOUT_INT)
+		ret |= tx_hard_error;
+
+	if (v & EMAC_TX_UNDERFLOW_INT) {
+		ret |= tx_hard_error;
+		x->tx_undeflow_irq++;
+	}
+
+	if (v & EMAC_TX_EARLY_INT)
+		x->tx_early_irq++;
+
+	if (v & EMAC_RX_INT) {
+		ret |= handle_rx;
+		x->rx_normal_irq_n++;
+	}
+
+	if (v & EMAC_RX_BUF_UA_INT)
+		x->rx_buf_unav_irq++;
+
+	if (v & EMAC_RX_DMA_STOP_INT)
+		x->rx_process_stopped_irq++;
+
+	if (v & EMAC_RX_TIMEOUT_INT)
+		ret |= tx_hard_error;
+
+	if (v & EMAC_RX_OVERFLOW_INT) {
+		ret |= tx_hard_error;
+		x->rx_overflow_irq++;
+	}
+
+	if (v & EMAC_RX_EARLY_INT)
+		x->rx_early_irq++;
+
+	if (v & EMAC_RGMII_STA_INT)
+		x->irq_rgmii_n++;
+
+	writel(v, ioaddr + EMAC_INT_STA);
+
+	return ret;
+}
+
+static void sun8i_dwmac_dma_operation_mode_rx(void __iomem *ioaddr, int mode,
+					      u32 channel, int fifosz, u8 qmode)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL1);
+	if (mode == SF_DMA_MODE) {
+		v |= EMAC_RX_MD;
+	} else {
+		v &= ~EMAC_RX_MD;
+		v &= ~EMAC_RX_TH_MASK;
+		if (mode < 32)
+			v |= EMAC_RX_TH_32;
+		else if (mode < 64)
+			v |= EMAC_RX_TH_64;
+		else if (mode < 96)
+			v |= EMAC_RX_TH_96;
+		else if (mode < 128)
+			v |= EMAC_RX_TH_128;
+	}
+	writel(v, ioaddr + EMAC_RX_CTL1);
+}
+
+static void sun8i_dwmac_dma_operation_mode_tx(void __iomem *ioaddr, int mode,
+					      u32 channel, int fifosz, u8 qmode)
+{
+	u32 v;
+
+	v = readl(ioaddr + EMAC_TX_CTL1);
+	if (mode == SF_DMA_MODE) {
+		v |= EMAC_TX_MD;
+		/* Undocumented bit (called TX_NEXT_FRM in BSP), the original
+		 * comment is
+		 * "Operating on second frame increase the performance
+		 * especially when transmit store-and-forward is used."
+		 */
+		v |= EMAC_TX_NEXT_FRM;
+	} else {
+		v &= ~EMAC_TX_MD;
+		v &= ~EMAC_TX_TH_MASK;
+		if (mode < 64)
+			v |= EMAC_TX_TH_64;
+		else if (mode < 128)
+			v |= EMAC_TX_TH_128;
+		else if (mode < 192)
+			v |= EMAC_TX_TH_192;
+		else if (mode < 256)
+			v |= EMAC_TX_TH_256;
+	}
+	writel(v, ioaddr + EMAC_TX_CTL1);
+}
+
+static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = {
+	.reset = sun8i_dwmac_dma_reset,
+	.init = sun8i_dwmac_dma_init,
+	.init_rx_chan = sun8i_dwmac_dma_init_rx,
+	.init_tx_chan = sun8i_dwmac_dma_init_tx,
+	.dump_regs = sun8i_dwmac_dump_regs,
+	.dma_rx_mode = sun8i_dwmac_dma_operation_mode_rx,
+	.dma_tx_mode = sun8i_dwmac_dma_operation_mode_tx,
+	.enable_dma_transmission = sun8i_dwmac_enable_dma_transmission,
+	.enable_dma_irq = sun8i_dwmac_enable_dma_irq,
+	.disable_dma_irq = sun8i_dwmac_disable_dma_irq,
+	.start_tx = sun8i_dwmac_dma_start_tx,
+	.stop_tx = sun8i_dwmac_dma_stop_tx,
+	.start_rx = sun8i_dwmac_dma_start_rx,
+	.stop_rx = sun8i_dwmac_dma_stop_rx,
+	.dma_interrupt = sun8i_dwmac_dma_interrupt,
+};
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv);
+
+static int sun8i_dwmac_init(struct platform_device *pdev, void *priv)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct sunxi_priv_data *gmac = priv;
+	int ret;
+
+	if (gmac->regulator) {
+		ret = regulator_enable(gmac->regulator);
+		if (ret) {
+			dev_err(&pdev->dev, "Fail to enable regulator\n");
+			return ret;
+		}
+	}
+
+	if (gmac->use_internal_phy) {
+		ret = sun8i_dwmac_power_internal_phy(netdev_priv(ndev));
+		if (ret)
+			goto err_disable_regulator;
+	}
+
+	return 0;
+
+err_disable_regulator:
+	if (gmac->regulator)
+		regulator_disable(gmac->regulator);
+
+	return ret;
+}
+
+static void sun8i_dwmac_core_init(struct mac_device_info *hw,
+				  struct net_device *dev)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */
+	writel(v, ioaddr + EMAC_BASIC_CTL1);
+}
+
+static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable)
+{
+	u32 t, r;
+
+	t = readl(ioaddr + EMAC_TX_CTL0);
+	r = readl(ioaddr + EMAC_RX_CTL0);
+	if (enable) {
+		t |= EMAC_TX_TRANSMITTER_EN;
+		r |= EMAC_RX_RECEIVER_EN;
+	} else {
+		t &= ~EMAC_TX_TRANSMITTER_EN;
+		r &= ~EMAC_RX_RECEIVER_EN;
+	}
+	writel(t, ioaddr + EMAC_TX_CTL0);
+	writel(r, ioaddr + EMAC_RX_CTL0);
+}
+
+/* Set MAC address at slot reg_n
+ * All slot > 0 need to be enabled with MAC_ADDR_TYPE_DST
+ * If addr is NULL, clear the slot
+ */
+static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw,
+				      const unsigned char *addr,
+				      unsigned int reg_n)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	if (!addr) {
+		writel(0, ioaddr + EMAC_MACADDR_HI(reg_n));
+		return;
+	}
+
+	stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+			    EMAC_MACADDR_LO(reg_n));
+	if (reg_n > 0) {
+		v = readl(ioaddr + EMAC_MACADDR_HI(reg_n));
+		v |= MAC_ADDR_TYPE_DST;
+		writel(v, ioaddr + EMAC_MACADDR_HI(reg_n));
+	}
+}
+
+static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw,
+				      unsigned char *addr,
+				      unsigned int reg_n)
+{
+	void __iomem *ioaddr = hw->pcsr;
+
+	stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n),
+			    EMAC_MACADDR_LO(reg_n));
+}
+
+/* caution this function must return non 0 to work */
+static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL0);
+	v |= EMAC_RX_DO_CRC;
+	writel(v, ioaddr + EMAC_RX_CTL0);
+
+	return 1;
+}
+
+static void sun8i_dwmac_set_filter(struct mac_device_info *hw,
+				   struct net_device *dev)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+	int i = 1;
+	struct netdev_hw_addr *ha;
+	int macaddrs = netdev_uc_count(dev) + netdev_mc_count(dev) + 1;
+
+	v = EMAC_FRM_FLT_CTL;
+
+	if (dev->flags & IFF_PROMISC) {
+		v = EMAC_FRM_FLT_RXALL;
+	} else if (dev->flags & IFF_ALLMULTI) {
+		v |= EMAC_FRM_FLT_MULTICAST;
+	} else if (macaddrs <= hw->unicast_filter_entries) {
+		if (!netdev_mc_empty(dev)) {
+			netdev_for_each_mc_addr(ha, dev) {
+				sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+				i++;
+			}
+		}
+		if (!netdev_uc_empty(dev)) {
+			netdev_for_each_uc_addr(ha, dev) {
+				sun8i_dwmac_set_umac_addr(hw, ha->addr, i);
+				i++;
+			}
+		}
+	} else {
+		if (!(readl(ioaddr + EMAC_RX_FRM_FLT) & EMAC_FRM_FLT_RXALL))
+			netdev_info(dev, "Too many address, switching to promiscuous\n");
+		v = EMAC_FRM_FLT_RXALL;
+	}
+
+	/* Disable unused address filter slots */
+	while (i < hw->unicast_filter_entries)
+		sun8i_dwmac_set_umac_addr(hw, NULL, i++);
+
+	writel(v, ioaddr + EMAC_RX_FRM_FLT);
+}
+
+static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw,
+				  unsigned int duplex, unsigned int fc,
+				  unsigned int pause_time, u32 tx_cnt)
+{
+	void __iomem *ioaddr = hw->pcsr;
+	u32 v;
+
+	v = readl(ioaddr + EMAC_RX_CTL0);
+	if (fc == FLOW_AUTO)
+		v |= EMAC_RX_FLOW_CTL_EN;
+	else
+		v &= ~EMAC_RX_FLOW_CTL_EN;
+	writel(v, ioaddr + EMAC_RX_CTL0);
+
+	v = readl(ioaddr + EMAC_TX_FLOW_CTL);
+	if (fc == FLOW_AUTO)
+		v |= EMAC_TX_FLOW_CTL_EN;
+	else
+		v &= ~EMAC_TX_FLOW_CTL_EN;
+	writel(v, ioaddr + EMAC_TX_FLOW_CTL);
+}
+
+static int sun8i_dwmac_reset(struct stmmac_priv *priv)
+{
+	u32 v;
+	int err;
+
+	v = readl(priv->ioaddr + EMAC_BASIC_CTL1);
+	writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1);
+
+	/* The timeout was previoulsy set to 10ms, but some board (OrangePI0)
+	 * need more if no cable plugged. 100ms seems OK
+	 */
+	err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v,
+				 !(v & 0x01), 100, 100000);
+
+	if (err) {
+		dev_err(priv->device, "EMAC reset timeout\n");
+		return err;
+	}
+	return 0;
+}
+
+/* Search in mdio-mux node for internal PHY node and get its clk/reset */
+static int get_ephy_nodes(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	struct device_node *mdio_mux, *iphynode;
+	struct device_node *mdio_internal;
+	int ret;
+
+	mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+	if (!mdio_mux) {
+		dev_err(priv->device, "Cannot get mdio-mux node\n");
+		return -ENODEV;
+	}
+
+	mdio_internal = of_get_compatible_child(mdio_mux,
+						"allwinner,sun8i-h3-mdio-internal");
+	of_node_put(mdio_mux);
+	if (!mdio_internal) {
+		dev_err(priv->device, "Cannot get internal_mdio node\n");
+		return -ENODEV;
+	}
+
+	/* Seek for internal PHY */
+	for_each_child_of_node(mdio_internal, iphynode) {
+		gmac->ephy_clk = of_clk_get(iphynode, 0);
+		if (IS_ERR(gmac->ephy_clk))
+			continue;
+		gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL);
+		if (IS_ERR(gmac->rst_ephy)) {
+			ret = PTR_ERR(gmac->rst_ephy);
+			if (ret == -EPROBE_DEFER) {
+				of_node_put(iphynode);
+				of_node_put(mdio_internal);
+				return ret;
+			}
+			continue;
+		}
+		dev_info(priv->device, "Found internal PHY node\n");
+		of_node_put(iphynode);
+		of_node_put(mdio_internal);
+		return 0;
+	}
+
+	of_node_put(mdio_internal);
+	return -ENODEV;
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	int ret;
+
+	if (gmac->internal_phy_powered) {
+		dev_warn(priv->device, "Internal PHY already powered\n");
+		return 0;
+	}
+
+	dev_info(priv->device, "Powering internal PHY\n");
+	ret = clk_prepare_enable(gmac->ephy_clk);
+	if (ret) {
+		dev_err(priv->device, "Cannot enable internal PHY\n");
+		return ret;
+	}
+
+	/* Make sure the EPHY is properly reseted, as U-Boot may leave
+	 * it at deasserted state, and thus it may fail to reset EMAC.
+	 *
+	 * This assumes the driver has exclusive access to the EPHY reset.
+	 */
+	ret = reset_control_reset(gmac->rst_ephy);
+	if (ret) {
+		dev_err(priv->device, "Cannot reset internal PHY\n");
+		clk_disable_unprepare(gmac->ephy_clk);
+		return ret;
+	}
+
+	gmac->internal_phy_powered = true;
+
+	return 0;
+}
+
+static void sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+	if (!gmac->internal_phy_powered)
+		return;
+
+	clk_disable_unprepare(gmac->ephy_clk);
+	reset_control_assert(gmac->rst_ephy);
+	gmac->internal_phy_powered = false;
+}
+
+/* MDIO multiplexing switch function
+ * This function is called by the mdio-mux layer when it thinks the mdio bus
+ * multiplexer needs to switch.
+ * 'current_child' is the current value of the mux register
+ * 'desired_child' is the value of the 'reg' property of the target child MDIO
+ * node.
+ * The first time this function is called, current_child == -1.
+ * If current_child == desired_child, then the mux is already set to the
+ * correct bus.
+ */
+static int mdio_mux_syscon_switch_fn(int current_child, int desired_child,
+				     void *data)
+{
+	struct stmmac_priv *priv = data;
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	u32 reg, val;
+	int ret = 0;
+
+	if (current_child ^ desired_child) {
+		regmap_field_read(gmac->regmap_field, &reg);
+		switch (desired_child) {
+		case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID:
+			dev_info(priv->device, "Switch mux to internal PHY");
+			val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT;
+			gmac->use_internal_phy = true;
+			break;
+		case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID:
+			dev_info(priv->device, "Switch mux to external PHY");
+			val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN;
+			gmac->use_internal_phy = false;
+			break;
+		default:
+			dev_err(priv->device, "Invalid child ID %x\n",
+				desired_child);
+			return -EINVAL;
+		}
+		regmap_field_write(gmac->regmap_field, val);
+		if (gmac->use_internal_phy) {
+			ret = sun8i_dwmac_power_internal_phy(priv);
+			if (ret)
+				return ret;
+		} else {
+			sun8i_dwmac_unpower_internal_phy(gmac);
+		}
+		/* After changing syscon value, the MAC need reset or it will
+		 * use the last value (and so the last PHY set).
+		 */
+		ret = sun8i_dwmac_reset(priv);
+	}
+	return ret;
+}
+
+static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv)
+{
+	int ret;
+	struct device_node *mdio_mux;
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+	mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+	if (!mdio_mux)
+		return -ENODEV;
+
+	ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn,
+			    &gmac->mux_handle, priv, priv->mii);
+	of_node_put(mdio_mux);
+	return ret;
+}
+
+static int sun8i_dwmac_set_syscon(struct device *dev,
+				  struct plat_stmmacenet_data *plat)
+{
+	struct sunxi_priv_data *gmac = plat->bsp_priv;
+	struct device_node *node = dev->of_node;
+	int ret;
+	u32 reg, val;
+
+	ret = regmap_field_read(gmac->regmap_field, &val);
+	if (ret) {
+		dev_err(dev, "Fail to read from regmap field.\n");
+		return ret;
+	}
+
+	reg = gmac->variant->default_syscon_value;
+	if (reg != val)
+		dev_warn(dev,
+			 "Current syscon value is not the default %x (expect %x)\n",
+			 val, reg);
+
+	if (gmac->variant->soc_has_internal_phy) {
+		if (of_property_read_bool(node, "allwinner,leds-active-low"))
+			reg |= H3_EPHY_LED_POL;
+		else
+			reg &= ~H3_EPHY_LED_POL;
+
+		/* Force EPHY xtal frequency to 24MHz. */
+		reg |= H3_EPHY_CLK_SEL;
+
+		ret = of_mdio_parse_addr(dev, plat->phy_node);
+		if (ret < 0) {
+			dev_err(dev, "Could not parse MDIO addr\n");
+			return ret;
+		}
+		/* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+		 * address. No need to mask it again.
+		 */
+		reg |= 1 << H3_EPHY_ADDR_SHIFT;
+	} else {
+		/* For SoCs without internal PHY the PHY selection bit should be
+		 * set to 0 (external PHY).
+		 */
+		reg &= ~H3_EPHY_SELECT;
+	}
+
+	if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
+		if (val % 100) {
+			dev_err(dev, "tx-delay must be a multiple of 100\n");
+			return -EINVAL;
+		}
+		val /= 100;
+		dev_dbg(dev, "set tx-delay to %x\n", val);
+		if (val <= gmac->variant->tx_delay_max) {
+			reg &= ~(gmac->variant->tx_delay_max <<
+				 SYSCON_ETXDC_SHIFT);
+			reg |= (val << SYSCON_ETXDC_SHIFT);
+		} else {
+			dev_err(dev, "Invalid TX clock delay: %d\n",
+				val);
+			return -EINVAL;
+		}
+	}
+
+	if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) {
+		if (val % 100) {
+			dev_err(dev, "rx-delay must be a multiple of 100\n");
+			return -EINVAL;
+		}
+		val /= 100;
+		dev_dbg(dev, "set rx-delay to %x\n", val);
+		if (val <= gmac->variant->rx_delay_max) {
+			reg &= ~(gmac->variant->rx_delay_max <<
+				 SYSCON_ERXDC_SHIFT);
+			reg |= (val << SYSCON_ERXDC_SHIFT);
+		} else {
+			dev_err(dev, "Invalid RX clock delay: %d\n",
+				val);
+			return -EINVAL;
+		}
+	}
+
+	/* Clear interface mode bits */
+	reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT);
+	if (gmac->variant->support_rmii)
+		reg &= ~SYSCON_RMII_EN;
+
+	switch (plat->interface) {
+	case PHY_INTERFACE_MODE_MII:
+		/* default */
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII;
+		break;
+	default:
+		dev_err(dev, "Unsupported interface mode: %s",
+			phy_modes(plat->interface));
+		return -EINVAL;
+	}
+
+	regmap_field_write(gmac->regmap_field, reg);
+
+	return 0;
+}
+
+static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac)
+{
+	u32 reg = gmac->variant->default_syscon_value;
+
+	regmap_field_write(gmac->regmap_field, reg);
+}
+
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+	struct sunxi_priv_data *gmac = priv;
+
+	if (gmac->variant->soc_has_internal_phy)
+		sun8i_dwmac_unpower_internal_phy(gmac);
+
+	if (gmac->regulator)
+		regulator_disable(gmac->regulator);
+}
+
+static void sun8i_dwmac_set_mac_loopback(void __iomem *ioaddr, bool enable)
+{
+	u32 value = readl(ioaddr + EMAC_BASIC_CTL0);
+
+	if (enable)
+		value |= EMAC_LOOPBACK;
+	else
+		value &= ~EMAC_LOOPBACK;
+
+	writel(value, ioaddr + EMAC_BASIC_CTL0);
+}
+
+static const struct stmmac_ops sun8i_dwmac_ops = {
+	.core_init = sun8i_dwmac_core_init,
+	.set_mac = sun8i_dwmac_set_mac,
+	.dump_regs = sun8i_dwmac_dump_mac_regs,
+	.rx_ipc = sun8i_dwmac_rx_ipc_enable,
+	.set_filter = sun8i_dwmac_set_filter,
+	.flow_ctrl = sun8i_dwmac_flow_ctrl,
+	.set_umac_addr = sun8i_dwmac_set_umac_addr,
+	.get_umac_addr = sun8i_dwmac_get_umac_addr,
+	.set_mac_loopback = sun8i_dwmac_set_mac_loopback,
+};
+
+static struct mac_device_info *sun8i_dwmac_setup(void *ppriv)
+{
+	struct mac_device_info *mac;
+	struct stmmac_priv *priv = ppriv;
+
+	mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
+	if (!mac)
+		return NULL;
+
+	mac->pcsr = priv->ioaddr;
+	mac->mac = &sun8i_dwmac_ops;
+	mac->dma = &sun8i_dwmac_dma_ops;
+
+	priv->dev->priv_flags |= IFF_UNICAST_FLT;
+
+	/* The loopback bit seems to be re-set when link change
+	 * Simply mask it each time
+	 * Speed 10/100/1000 are set in BIT(2)/BIT(3)
+	 */
+	mac->link.speed_mask = GENMASK(3, 2) | EMAC_LOOPBACK;
+	mac->link.speed10 = EMAC_SPEED_10;
+	mac->link.speed100 = EMAC_SPEED_100;
+	mac->link.speed1000 = EMAC_SPEED_1000;
+	mac->link.duplex = EMAC_DUPLEX_FULL;
+	mac->mii.addr = EMAC_MDIO_CMD;
+	mac->mii.data = EMAC_MDIO_DATA;
+	mac->mii.reg_shift = 4;
+	mac->mii.reg_mask = GENMASK(8, 4);
+	mac->mii.addr_shift = 12;
+	mac->mii.addr_mask = GENMASK(16, 12);
+	mac->mii.clk_csr_shift = 20;
+	mac->mii.clk_csr_mask = GENMASK(22, 20);
+	mac->unicast_filter_entries = 8;
+
+	/* Synopsys Id is not available */
+	priv->synopsys_id = 0;
+
+	return mac;
+}
+
+static struct regmap *sun8i_dwmac_get_syscon_from_dev(struct device_node *node)
+{
+	struct device_node *syscon_node;
+	struct platform_device *syscon_pdev;
+	struct regmap *regmap = NULL;
+
+	syscon_node = of_parse_phandle(node, "syscon", 0);
+	if (!syscon_node)
+		return ERR_PTR(-ENODEV);
+
+	syscon_pdev = of_find_device_by_node(syscon_node);
+	if (!syscon_pdev) {
+		/* platform device might not be probed yet */
+		regmap = ERR_PTR(-EPROBE_DEFER);
+		goto out_put_node;
+	}
+
+	/* If no regmap is found then the other device driver is at fault */
+	regmap = dev_get_regmap(&syscon_pdev->dev, NULL);
+	if (!regmap)
+		regmap = ERR_PTR(-EINVAL);
+
+	platform_device_put(syscon_pdev);
+out_put_node:
+	of_node_put(syscon_node);
+	return regmap;
+}
+
+static int sun8i_dwmac_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct sunxi_priv_data *gmac;
+	struct device *dev = &pdev->dev;
+	phy_interface_t interface;
+	int ret;
+	struct stmmac_priv *priv;
+	struct net_device *ndev;
+	struct regmap *regmap;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL);
+	if (!gmac)
+		return -ENOMEM;
+
+	gmac->variant = of_device_get_match_data(&pdev->dev);
+	if (!gmac->variant) {
+		dev_err(&pdev->dev, "Missing dwmac-sun8i variant\n");
+		return -EINVAL;
+	}
+
+	/* Optional regulator for PHY */
+	gmac->regulator = devm_regulator_get_optional(dev, "phy");
+	if (IS_ERR(gmac->regulator)) {
+		if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		dev_info(dev, "No regulator found\n");
+		gmac->regulator = NULL;
+	}
+
+	/* The "GMAC clock control" register might be located in the
+	 * CCU address range (on the R40), or the system control address
+	 * range (on most other sun8i and later SoCs).
+	 *
+	 * The former controls most if not all clocks in the SoC. The
+	 * latter has an SoC identification register, and on some SoCs,
+	 * controls to map device specific SRAM to either the intended
+	 * peripheral, or the CPU address space.
+	 *
+	 * In either case, there should be a coordinated and restricted
+	 * method of accessing the register needed here. This is done by
+	 * having the device export a custom regmap, instead of a generic
+	 * syscon, which grants all access to all registers.
+	 *
+	 * To support old device trees, we fall back to using the syscon
+	 * interface if possible.
+	 */
+	regmap = sun8i_dwmac_get_syscon_from_dev(pdev->dev.of_node);
+	if (IS_ERR(regmap))
+		regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+							 "syscon");
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret);
+		return ret;
+	}
+
+	gmac->regmap_field = devm_regmap_field_alloc(dev, regmap,
+						     *gmac->variant->syscon_field);
+	if (IS_ERR(gmac->regmap_field)) {
+		ret = PTR_ERR(gmac->regmap_field);
+		dev_err(dev, "Unable to map syscon register: %d\n", ret);
+		return ret;
+	}
+
+	ret = of_get_phy_mode(dev->of_node, &interface);
+	if (ret)
+		return -EINVAL;
+
+	plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	/* platform data specifying hardware features and callbacks.
+	 * hardware features were copied from Allwinner drivers.
+	 */
+	plat_dat->interface = interface;
+	plat_dat->rx_coe = STMMAC_RX_COE_TYPE2;
+	plat_dat->tx_coe = 1;
+	plat_dat->has_sun8i = true;
+	plat_dat->bsp_priv = gmac;
+	plat_dat->init = sun8i_dwmac_init;
+	plat_dat->exit = sun8i_dwmac_exit;
+	plat_dat->setup = sun8i_dwmac_setup;
+	plat_dat->tx_fifo_size = 4096;
+	plat_dat->rx_fifo_size = 16384;
+
+	ret = sun8i_dwmac_set_syscon(&pdev->dev, plat_dat);
+	if (ret)
+		goto dwmac_deconfig;
+
+	ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv);
+	if (ret)
+		goto dwmac_syscon;
+
+	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+	if (ret)
+		goto dwmac_exit;
+
+	ndev = dev_get_drvdata(&pdev->dev);
+	priv = netdev_priv(ndev);
+
+	/* the MAC is runtime suspended after stmmac_dvr_probe(), so we
+	 * need to ensure the MAC resume back before other operations such
+	 * as reset.
+	 */
+	pm_runtime_get_sync(&pdev->dev);
+
+	/* The mux must be registered after parent MDIO
+	 * so after stmmac_dvr_probe()
+	 */
+	if (gmac->variant->soc_has_internal_phy) {
+		ret = get_ephy_nodes(priv);
+		if (ret)
+			goto dwmac_remove;
+		ret = sun8i_dwmac_register_mdio_mux(priv);
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to register mux\n");
+			goto dwmac_mux;
+		}
+	} else {
+		ret = sun8i_dwmac_reset(priv);
+		if (ret)
+			goto dwmac_remove;
+	}
+
+	pm_runtime_put(&pdev->dev);
+
+	return 0;
+
+dwmac_mux:
+	reset_control_put(gmac->rst_ephy);
+	clk_put(gmac->ephy_clk);
+dwmac_remove:
+	pm_runtime_put_noidle(&pdev->dev);
+	stmmac_dvr_remove(&pdev->dev);
+dwmac_exit:
+	sun8i_dwmac_exit(pdev, gmac);
+dwmac_syscon:
+	sun8i_dwmac_unset_syscon(gmac);
+dwmac_deconfig:
+	stmmac_remove_config_dt(pdev, plat_dat);
+
+	return ret;
+}
+
+static int sun8i_dwmac_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+	if (gmac->variant->soc_has_internal_phy) {
+		mdio_mux_uninit(gmac->mux_handle);
+		sun8i_dwmac_unpower_internal_phy(gmac);
+		reset_control_put(gmac->rst_ephy);
+		clk_put(gmac->ephy_clk);
+	}
+
+	stmmac_pltfr_remove(pdev);
+	sun8i_dwmac_unset_syscon(gmac);
+
+	return 0;
+}
+
+static void sun8i_dwmac_shutdown(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+	sun8i_dwmac_exit(pdev, gmac);
+}
+
+static const struct of_device_id sun8i_dwmac_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-emac",
+		.data = &emac_variant_h3 },
+	{ .compatible = "allwinner,sun8i-v3s-emac",
+		.data = &emac_variant_v3s },
+	{ .compatible = "allwinner,sun8i-a83t-emac",
+		.data = &emac_variant_a83t },
+	{ .compatible = "allwinner,sun8i-r40-gmac",
+		.data = &emac_variant_r40 },
+	{ .compatible = "allwinner,sun50i-a64-emac",
+		.data = &emac_variant_a64 },
+	{ .compatible = "allwinner,sun50i-h6-emac",
+		.data = &emac_variant_h6 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
+
+static struct platform_driver sun8i_dwmac_driver = {
+	.probe  = sun8i_dwmac_probe,
+	.remove = sun8i_dwmac_remove,
+	.shutdown = sun8i_dwmac_shutdown,
+	.driver = {
+		.name           = "dwmac-sun8i",
+		.pm		= &stmmac_pltfr_pm_ops,
+		.of_match_table = sun8i_dwmac_match,
+	},
+};
+module_platform_driver(sun8i_dwmac_driver);
+
+MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com>");
+MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer");
+MODULE_LICENSE("GPL");