Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 328 insertions, 0 deletions

diff --git a/drivers/spi/spi-lm70llp.c b/drivers/spi/spi-lm70llp.c
new file mode 100644
index 000000000..ead0507c6
--- /dev/null
+++ b/drivers/spi/spi-lm70llp.c
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for LM70EVAL-LLP board for the LM70 sensor
+ *
+ * Copyright (C) 2006 Kaiwan N Billimoria <kaiwan@designergraphix.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/parport.h>
+#include <linux/sysfs.h>
+#include <linux/workqueue.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+/*
+ * The LM70 communicates with a host processor using a 3-wire variant of
+ * the SPI/Microwire bus interface. This driver specifically supports an
+ * NS LM70 LLP Evaluation Board, interfacing to a PC using its parallel
+ * port to bitbang an SPI-parport bridge.  Accordingly, this is an SPI
+ * master controller driver.  The hwmon/lm70 driver is a "SPI protocol
+ * driver", layered on top of this one and usable without the lm70llp.
+ *
+ * Datasheet and Schematic:
+ * The LM70 is a temperature sensor chip from National Semiconductor; its
+ * datasheet is available at http://www.national.com/pf/LM/LM70.html
+ * The schematic for this particular board (the LM70EVAL-LLP) is
+ * available (on page 4) here:
+ *  http://www.national.com/appinfo/tempsensors/files/LM70LLPEVALmanual.pdf
+ *
+ * Also see Documentation/spi/spi-lm70llp.rst.  The SPI<->parport code here is
+ * (heavily) based on spi-butterfly by David Brownell.
+ *
+ * The LM70 LLP connects to the PC parallel port in the following manner:
+ *
+ *   Parallel                 LM70 LLP
+ *     Port      Direction   JP2 Header
+ *  -----------  ---------  ------------
+ *      D0    2      -         -
+ *      D1    3     -->      V+   5
+ *      D2    4     -->      V+   5
+ *      D3    5     -->      V+   5
+ *      D4    6     -->      V+   5
+ *      D5    7     -->      nCS  8
+ *      D6    8     -->      SCLK 3
+ *      D7    9     -->      SI/O 5
+ *     GND   25      -       GND  7
+ *    Select 13     <--      SI/O 1
+ *
+ * Note that parport pin 13 actually gets inverted by the transistor
+ * arrangement which lets either the parport or the LM70 drive the
+ * SI/SO signal (see the schematic for details).
+ */
+
+#define DRVNAME		"spi-lm70llp"
+
+#define lm70_INIT	0xBE
+#define SIO		0x10
+#define nCS		0x20
+#define SCLK		0x40
+
+/*-------------------------------------------------------------------------*/
+
+struct spi_lm70llp {
+	struct spi_bitbang	bitbang;
+	struct parport		*port;
+	struct pardevice	*pd;
+	struct spi_device	*spidev_lm70;
+	struct spi_board_info	info;
+	//struct device		*dev;
+};
+
+/* REVISIT : ugly global ; provides "exclusive open" facility */
+static struct spi_lm70llp *lm70llp;
+
+/*-------------------------------------------------------------------*/
+
+static inline struct spi_lm70llp *spidev_to_pp(struct spi_device *spi)
+{
+	return spi->controller_data;
+}
+
+/*---------------------- LM70 LLP eval board-specific inlines follow */
+
+/* NOTE:  we don't actually need to reread the output values, since they'll
+ * still be what we wrote before.  Plus, going through parport builds in
+ * a ~1ms/operation delay; these SPI transfers could easily be faster.
+ */
+
+static inline void deassertCS(struct spi_lm70llp *pp)
+{
+	u8 data = parport_read_data(pp->port);
+
+	data &= ~0x80;		/* pull D7/SI-out low while de-asserted */
+	parport_write_data(pp->port, data | nCS);
+}
+
+static inline void assertCS(struct spi_lm70llp *pp)
+{
+	u8 data = parport_read_data(pp->port);
+
+	data |= 0x80;		/* pull D7/SI-out high so lm70 drives SO-in */
+	parport_write_data(pp->port, data & ~nCS);
+}
+
+static inline void clkHigh(struct spi_lm70llp *pp)
+{
+	u8 data = parport_read_data(pp->port);
+
+	parport_write_data(pp->port, data | SCLK);
+}
+
+static inline void clkLow(struct spi_lm70llp *pp)
+{
+	u8 data = parport_read_data(pp->port);
+
+	parport_write_data(pp->port, data & ~SCLK);
+}
+
+/*------------------------- SPI-LM70-specific inlines ----------------------*/
+
+static inline void spidelay(unsigned d)
+{
+	udelay(d);
+}
+
+static inline void setsck(struct spi_device *s, int is_on)
+{
+	struct spi_lm70llp *pp = spidev_to_pp(s);
+
+	if (is_on)
+		clkHigh(pp);
+	else
+		clkLow(pp);
+}
+
+static inline void setmosi(struct spi_device *s, int is_on)
+{
+	/* FIXME update D7 ... this way we can put the chip
+	 * into shutdown mode and read the manufacturer ID,
+	 * but we can't put it back into operational mode.
+	 */
+}
+
+/*
+ * getmiso:
+ * Why do we return 0 when the SIO line is high and vice-versa?
+ * The fact is, the lm70 eval board from NS (which this driver drives),
+ * is wired in just such a way : when the lm70's SIO goes high, a transistor
+ * switches it to low reflecting this on the parport (pin 13), and vice-versa.
+ */
+static inline int getmiso(struct spi_device *s)
+{
+	struct spi_lm70llp *pp = spidev_to_pp(s);
+
+	return ((SIO == (parport_read_status(pp->port) & SIO)) ? 0 : 1);
+}
+
+/*--------------------------------------------------------------------*/
+
+#include "spi-bitbang-txrx.h"
+
+static void lm70_chipselect(struct spi_device *spi, int value)
+{
+	struct spi_lm70llp *pp = spidev_to_pp(spi);
+
+	if (value)
+		assertCS(pp);
+	else
+		deassertCS(pp);
+}
+
+/*
+ * Our actual bitbanger routine.
+ */
+static u32 lm70_txrx(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits,
+		     unsigned flags)
+{
+	return bitbang_txrx_be_cpha0(spi, nsecs, 0, flags, word, bits);
+}
+
+static void spi_lm70llp_attach(struct parport *p)
+{
+	struct pardevice	*pd;
+	struct spi_lm70llp	*pp;
+	struct spi_master	*master;
+	int			status;
+	struct pardev_cb	lm70llp_cb;
+
+	if (lm70llp) {
+		pr_warn("spi_lm70llp instance already loaded. Aborting.\n");
+		return;
+	}
+
+	/* TODO:  this just _assumes_ a lm70 is there ... no probe;
+	 * the lm70 driver could verify it, reading the manf ID.
+	 */
+
+	master = spi_alloc_master(p->physport->dev, sizeof(*pp));
+	if (!master) {
+		status = -ENOMEM;
+		goto out_fail;
+	}
+	pp = spi_master_get_devdata(master);
+
+	/*
+	 * SPI and bitbang hookup.
+	 */
+	pp->bitbang.master = master;
+	pp->bitbang.chipselect = lm70_chipselect;
+	pp->bitbang.txrx_word[SPI_MODE_0] = lm70_txrx;
+	pp->bitbang.flags = SPI_3WIRE;
+
+	/*
+	 * Parport hookup
+	 */
+	pp->port = p;
+	memset(&lm70llp_cb, 0, sizeof(lm70llp_cb));
+	lm70llp_cb.private = pp;
+	lm70llp_cb.flags = PARPORT_FLAG_EXCL;
+	pd = parport_register_dev_model(p, DRVNAME, &lm70llp_cb, 0);
+
+	if (!pd) {
+		status = -ENOMEM;
+		goto out_free_master;
+	}
+	pp->pd = pd;
+
+	status = parport_claim(pd);
+	if (status < 0)
+		goto out_parport_unreg;
+
+	/*
+	 * Start SPI ...
+	 */
+	status = spi_bitbang_start(&pp->bitbang);
+	if (status < 0) {
+		dev_warn(&pd->dev, "spi_bitbang_start failed with status %d\n",
+			 status);
+		goto out_off_and_release;
+	}
+
+	/*
+	 * The modalias name MUST match the device_driver name
+	 * for the bus glue code to match and subsequently bind them.
+	 * We are binding to the generic drivers/hwmon/lm70.c device
+	 * driver.
+	 */
+	strcpy(pp->info.modalias, "lm70");
+	pp->info.max_speed_hz = 6 * 1000 * 1000;
+	pp->info.chip_select = 0;
+	pp->info.mode = SPI_3WIRE | SPI_MODE_0;
+
+	/* power up the chip, and let the LM70 control SI/SO */
+	parport_write_data(pp->port, lm70_INIT);
+
+	/* Enable access to our primary data structure via
+	 * the board info's (void *)controller_data.
+	 */
+	pp->info.controller_data = pp;
+	pp->spidev_lm70 = spi_new_device(pp->bitbang.master, &pp->info);
+	if (pp->spidev_lm70)
+		dev_dbg(&pp->spidev_lm70->dev, "spidev_lm70 at %s\n",
+			dev_name(&pp->spidev_lm70->dev));
+	else {
+		dev_warn(&pd->dev, "spi_new_device failed\n");
+		status = -ENODEV;
+		goto out_bitbang_stop;
+	}
+	pp->spidev_lm70->bits_per_word = 8;
+
+	lm70llp = pp;
+	return;
+
+out_bitbang_stop:
+	spi_bitbang_stop(&pp->bitbang);
+out_off_and_release:
+	/* power down */
+	parport_write_data(pp->port, 0);
+	mdelay(10);
+	parport_release(pp->pd);
+out_parport_unreg:
+	parport_unregister_device(pd);
+out_free_master:
+	spi_master_put(master);
+out_fail:
+	pr_info("spi_lm70llp probe fail, status %d\n", status);
+}
+
+static void spi_lm70llp_detach(struct parport *p)
+{
+	struct spi_lm70llp		*pp;
+
+	if (!lm70llp || lm70llp->port != p)
+		return;
+
+	pp = lm70llp;
+	spi_bitbang_stop(&pp->bitbang);
+
+	/* power down */
+	parport_write_data(pp->port, 0);
+
+	parport_release(pp->pd);
+	parport_unregister_device(pp->pd);
+
+	spi_master_put(pp->bitbang.master);
+
+	lm70llp = NULL;
+}
+
+static struct parport_driver spi_lm70llp_drv = {
+	.name =		DRVNAME,
+	.match_port =	spi_lm70llp_attach,
+	.detach =	spi_lm70llp_detach,
+	.devmodel =	true,
+};
+module_parport_driver(spi_lm70llp_drv);
+
+MODULE_AUTHOR("Kaiwan N Billimoria <kaiwan@designergraphix.com>");
+MODULE_DESCRIPTION(
+	"Parport adapter for the National Semiconductor LM70 LLP eval board");
+MODULE_LICENSE("GPL");