diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock/idt,versaclock5.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/clock/idt,versaclock5.yaml | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml new file mode 100644 index 000000000..f9ba9864d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for IDT VersaClock 5 and 6 programmable I2C clock generators + +description: | + The IDT VersaClock 5 and VersaClock 6 are programmable I2C + clock generators providing from 3 to 12 output clocks. + + When referencing the provided clock in the DT using phandle and clock + specifier, the following mapping applies: + + - 5P49V5923: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + + - 5P49V5933: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT4 + + - other parts: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + 3 -- OUT3 + 4 -- OUT4 + + The idt,shutdown and idt,output-enable-active properties control the + SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown + Register, respectively. Their behavior is summarized by the following + table: + + SH SP Output when the SD/OE pin is Low/High + == == ===================================== + 0 0 Active/Inactive + 0 1 Inactive/Active + 1 0 Active/Shutdown + 1 1 Inactive/Shutdown + + The case where SH and SP are both 1 is likely not very interesting. + +maintainers: + - Luca Ceresoli <luca.ceresoli@bootlin.com> + +properties: + compatible: + enum: + - idt,5p49v5923 + - idt,5p49v5925 + - idt,5p49v5933 + - idt,5p49v5935 + - idt,5p49v6901 + - idt,5p49v6965 + - idt,5p49v6975 + + reg: + description: I2C device address + enum: [ 0x68, 0x6a ] + + '#clock-cells': + const: 1 + + clock-names: + minItems: 1 + maxItems: 2 + items: + enum: [ xin, clkin ] + clocks: + minItems: 1 + maxItems: 2 + + idt,xtal-load-femtofarads: + minimum: 9000 + maximum: 22760 + description: Optional load capacitor for XTAL1 and XTAL2 + + idt,shutdown: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + If 1, this enables the shutdown functionality: the chip will be + shut down if the SD/OE pin is driven high. If 0, this disables the + shutdown functionality: the chip will never be shut down based on + the value of the SD/OE pin. This property corresponds to the SH + bit of the Primary Source and Shutdown Register. + + idt,output-enable-active: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + If 1, this enables output when the SD/OE pin is high, and disables + output when the SD/OE pin is low. If 0, this disables output when + the SD/OE pin is high, and enables output when the SD/OE pin is + low. This corresponds to the SP bit of the Primary Source and + Shutdown Register. + +patternProperties: + "^OUT[1-4]$": + type: object + description: + Description of one of the outputs (OUT1..OUT4). See "Clock1 Output + Configuration" in the Versaclock 5/6/6E Family Register Description + and Programming Guide. + properties: + idt,mode: + description: + The output drive mode. Values defined in dt-bindings/clock/versaclock.h + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 6 + idt,voltage-microvolt: + description: The output drive voltage. + enum: [ 1800000, 2500000, 3300000 ] + idt,slew-percent: + description: The Slew rate control for CMOS single-ended. + enum: [ 80, 85, 90, 100 ] + additionalProperties: false + +required: + - compatible + - reg + - '#clock-cells' + - idt,shutdown + - idt,output-enable-active + +allOf: + - if: + properties: + compatible: + enum: + - idt,5p49v5933 + - idt,5p49v5935 + - idt,5p49v6975 + then: + # Devices with builtin crystal + optional external input + properties: + clock-names: + const: clkin + clocks: + maxItems: 1 + else: + # Devices without builtin crystal + required: + - clock-names + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/versaclock.h> + + /* 25MHz reference crystal */ + ref25: ref25m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + i2c@0 { + reg = <0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + /* IDT 5P49V5923 I2C clock generator */ + vc5: clock-generator@6a { + compatible = "idt,5p49v5923"; + reg = <0x6a>; + #clock-cells = <1>; + + /* Connect XIN input to 25MHz reference */ + clocks = <&ref25m>; + clock-names = "xin"; + + /* Set the SD/OE pin's settings */ + idt,shutdown = <0>; + idt,output-enable-active = <0>; + + OUT1 { + idt,mode = <VC5_CMOSD>; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <80>; + }; + + OUT4 { + idt,mode = <VC5_LVDS>; + }; + }; + }; + +... |