diff options
Diffstat (limited to '')
129 files changed, 9562 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/adc-joystick.yaml b/Documentation/devicetree/bindings/input/adc-joystick.yaml new file mode 100644 index 000000000..da0f8dfca --- /dev/null +++ b/Documentation/devicetree/bindings/input/adc-joystick.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019-2020 Artur Rojek +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/input/adc-joystick.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: ADC attached joystick + +maintainers: + - Artur Rojek <contact@artur-rojek.eu> + +description: > + Bindings for joystick devices connected to ADC controllers supporting + the Industrial I/O subsystem. + +allOf: + - $ref: input.yaml# + +properties: + compatible: + const: adc-joystick + + io-channels: + minItems: 1 + maxItems: 1024 + description: > + List of phandle and IIO specifier pairs. + Each pair defines one ADC channel to which a joystick axis is connected. + See + https://github.com/devicetree-org/dt-schema/blob/master/schemas/iio/iio-consumer.yaml + for details. + + poll-interval: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +required: + - compatible + - io-channels + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +patternProperties: + "^axis@[0-9a-f]+$": + type: object + $ref: input.yaml# + description: > + Represents a joystick axis bound to the given ADC channel. + For each entry in the io-channels list, one axis subnode with a matching + reg property must be specified. + + properties: + reg: + minimum: 0 + maximum: 1023 + description: Index of an io-channels list entry bound to this axis. + + linux,code: + description: EV_ABS specific event code generated by the axis. + + abs-range: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: minimum value + - description: maximum value + description: > + Minimum and maximum values produced by the axis. + For an ABS_X axis this will be the left-most and right-most + inclination of the joystick. If min > max, it is left to userspace to + treat the axis as inverted. + This property is interpreted as two signed 32 bit values. + + abs-fuzz: + $ref: /schemas/types.yaml#/definitions/uint32 + description: > + Amount of noise in the input value. + Omitting this property indicates the axis is precise. + + abs-flat: + $ref: /schemas/types.yaml#/definitions/uint32 + description: > + Axial "deadzone", or area around the center position, where the axis + is considered to be at rest. + Omitting this property indicates the axis always returns to exactly + the center position. + + required: + - reg + - linux,code + - abs-range + + additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/adc/ingenic,adc.h> + #include <dt-bindings/input/input.h> + + joystick: adc-joystick { + compatible = "adc-joystick"; + io-channels = <&adc INGENIC_ADC_TOUCH_XP>, + <&adc INGENIC_ADC_TOUCH_YP>; + #address-cells = <1>; + #size-cells = <0>; + + axis@0 { + reg = <0>; + linux,code = <ABS_X>; + abs-range = <3300 0>; + abs-fuzz = <4>; + abs-flat = <200>; + }; + axis@1 { + reg = <1>; + linux,code = <ABS_Y>; + abs-range = <0 3300>; + abs-fuzz = <4>; + abs-flat = <200>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/adc-keys.yaml b/Documentation/devicetree/bindings/input/adc-keys.yaml new file mode 100644 index 000000000..7aa078dea --- /dev/null +++ b/Documentation/devicetree/bindings/input/adc-keys.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/adc-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADC attached resistor ladder buttons + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + +allOf: + - $ref: input.yaml# + +properties: + compatible: + const: adc-keys + + io-channels: + maxItems: 1 + + io-channel-names: + const: buttons + + keyup-threshold-microvolt: + description: + Voltage above or equal to which all the keys are considered up. + + poll-interval: true + autorepeat: true + +patternProperties: + '^button-': + type: object + $ref: input.yaml# + additionalProperties: false + description: + Each button (key) is represented as a sub-node. + + properties: + label: true + + linux,code: true + + press-threshold-microvolt: + description: + Voltage above or equal to which this key is considered pressed. No + two values of press-threshold-microvolt may be the same. All values + of press-threshold-microvolt must be less than + keyup-threshold-microvolt. + + required: + - linux,code + - press-threshold-microvolt + +required: + - compatible + - io-channels + - io-channel-names + - keyup-threshold-microvolt + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + // +--------------------------------+------------------------+ + // | 2.000.000 <= value | no key pressed | + // +--------------------------------+------------------------+ + // | 1.500.000 <= value < 2.000.000 | KEY_VOLUMEUP pressed | + // +--------------------------------+------------------------+ + // | 1.000.000 <= value < 1.500.000 | KEY_VOLUMEDOWN pressed | + // +--------------------------------+------------------------+ + // | 500.000 <= value < 1.000.000 | KEY_ENTER pressed | + // +--------------------------------+------------------------+ + // | value < 500.000 | no key pressed | + // +--------------------------------+------------------------+ + + adc-keys { + compatible = "adc-keys"; + io-channels = <&lradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <2000000>; + + button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <1500000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <1000000>; + }; + + button-enter { + label = "Enter"; + linux,code = <KEY_ENTER>; + press-threshold-microvolt = <500000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/input/adi,adp5588.yaml b/Documentation/devicetree/bindings/input/adi,adp5588.yaml new file mode 100644 index 000000000..26ea66834 --- /dev/null +++ b/Documentation/devicetree/bindings/input/adi,adp5588.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/adi,adp5588.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADP5588 Keypad Controller + +maintainers: + - Nuno Sá <nuno.sa@analog.com> + +description: | + Analog Devices Mobile I/O Expander and QWERTY Keypad Controller + https://www.analog.com/media/en/technical-documentation/data-sheets/ADP5588.pdf + +allOf: + - $ref: matrix-keymap.yaml# + - $ref: input.yaml# + +properties: + compatible: + enum: + - adi,adp5587 + - adi,adp5588 + + reg: + maxItems: 1 + + vcc-supply: + description: Supply Voltage Input + + reset-gpios: + description: + If specified, it will be asserted during driver probe. As the line is + active low, it should be marked GPIO_ACTIVE_LOW. + maxItems: 1 + + interrupts: + maxItems: 1 + + gpio-controller: + description: + This property applies if either keypad,num-rows lower than 8 or + keypad,num-columns lower than 10. + + '#gpio-cells': + const: 2 + + interrupt-controller: + description: + This property applies if either keypad,num-rows lower than 8 or + keypad,num-columns lower than 10. + + '#interrupt-cells': + const: 2 + + adi,unlock-keys: + description: + Specifies a maximum of 2 keys that can be used to unlock the keypad. + If this property is set, the keyboard will be locked and only unlocked + after these keys are pressed. If only one key is set, a double click is + needed to unlock the keypad. The value of this property cannot be bigger + or equal than keypad,num-rows * keypad,num-columns. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 2 + +required: + - compatible + - reg + - interrupts + - keypad,num-rows + - keypad,num-columns + - linux,keymap + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/input/input.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + keys@34 { + compatible = "adi,adp5588"; + reg = <0x34>; + + vcc-supply = <&vcc>; + interrupts = <21 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + + keypad,num-rows = <1>; + keypad,num-columns = <9>; + linux,keymap = < + MATRIX_KEY(0x00, 0x00, KEY_1) + MATRIX_KEY(0x00, 0x01, KEY_2) + MATRIX_KEY(0x00, 0x02, KEY_3) + MATRIX_KEY(0x00, 0x03, KEY_4) + MATRIX_KEY(0x00, 0x04, KEY_5) + MATRIX_KEY(0x00, 0x05, KEY_6) + MATRIX_KEY(0x00, 0x06, KEY_7) + MATRIX_KEY(0x00, 0x07, KEY_8) + MATRIX_KEY(0x00, 0x08, KEY_9) + >; + }; + }; +... diff --git a/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml b/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml new file mode 100644 index 000000000..5d631f713 --- /dev/null +++ b/Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml @@ -0,0 +1,117 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/allwinner,sun4i-a10-lradc-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 LRADC + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-lradc-keys + - const: allwinner,sun8i-a83t-r-lradc + - items: + - const: allwinner,sun50i-a64-lradc + - const: allwinner,sun8i-a83t-r-lradc + - const: allwinner,sun50i-r329-lradc + - items: + - const: allwinner,sun20i-d1-lradc + - const: allwinner,sun50i-r329-lradc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + interrupts: + maxItems: 1 + + vref-supply: + description: + Regulator for the LRADC reference voltage + + wakeup-source: true + +patternProperties: + "^button-[0-9]+$": + type: object + $ref: input.yaml# + properties: + label: + $ref: /schemas/types.yaml#/definitions/string + description: Descriptive name of the key + + linux,code: true + + channel: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: ADC Channel this key is attached to + + voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Voltage in microvolts at LRADC input when this key is + pressed + + required: + - label + - linux,code + - channel + - voltage + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - vref-supply + +if: + properties: + compatible: + contains: + enum: + - allwinner,sun50i-r329-lradc + +then: + required: + - clocks + - resets + +additionalProperties: false + +examples: + - | + lradc: lradc@1c22800 { + compatible = "allwinner,sun4i-a10-lradc-keys"; + reg = <0x01c22800 0x100>; + interrupts = <31>; + vref-supply = <®_vcc3v0>; + + button-191 { + label = "Volume Up"; + linux,code = <115>; + channel = <0>; + voltage = <191274>; + }; + + button-392 { + label = "Volume Down"; + linux,code = <114>; + channel = <0>; + voltage = <392644>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/ariel-pwrbutton.yaml b/Documentation/devicetree/bindings/input/ariel-pwrbutton.yaml new file mode 100644 index 000000000..442f623bb --- /dev/null +++ b/Documentation/devicetree/bindings/input/ariel-pwrbutton.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/ariel-pwrbutton.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dell Wyse 3020 a.k.a. "Ariel" Power Button + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +description: | + The ENE Embedded Controller on the Ariel board has an interface to the + SPI bus that is capable of sending keyboard and mouse data. A single + power button is attached to it. This binding describes this + configuration. + +allOf: + - $ref: input.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + items: + - const: dell,wyse-ariel-ec-input + - const: ene,kb3930-input + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + spi-max-frequency: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + power-button@0 { + compatible = "dell,wyse-ariel-ec-input", "ene,kb3930-input"; + reg = <0>; + interrupt-parent = <&gpio>; + interrupts = <60 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <33000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/atmel,captouch.txt b/Documentation/devicetree/bindings/input/atmel,captouch.txt new file mode 100644 index 000000000..fe9ee5c53 --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,captouch.txt @@ -0,0 +1,36 @@ +Device tree bindings for Atmel capacitive touch device, typically +an Atmel touch sensor connected to AtmegaXX MCU running firmware +based on Qtouch library. + +The node for this device must be a child of a I2C controller node, as the +device communicates via I2C. + +Required properties: + + compatible: Must be "atmel,captouch". + reg: The I2C slave address of the device. + interrupts: Property describing the interrupt line the device + is connected to. The device only has one interrupt + source. + linux,keycodes: Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 8 entries. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + +Example: + + atmel-captouch@51 { + compatible = "atmel,captouch"; + reg = <0x51>; + interrupt-parent = <&tlmm>; + interrupts = <67 IRQ_TYPE_EDGE_FALLING>; + linux,keycodes = <BTN_0>, <BTN_1>, + <BTN_2>, <BTN_3>, + <BTN_4>, <BTN_5>, + <BTN_6>, <BTN_7>; + autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml new file mode 100644 index 000000000..3ec579d63 --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/atmel,maxtouch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel maXTouch touchscreen/touchpad + +maintainers: + - Nick Dyer <nick@shmanahar.org> + - Linus Walleij <linus.walleij@linaro.org> + +description: | + Atmel maXTouch touchscreen or touchpads such as the mXT244 + and similar devices. + +properties: + compatible: + const: atmel,maxtouch + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdda-supply: + description: + Optional regulator for the AVDD analog voltage. + + vdd-supply: + description: + Optional regulator for the VDD digital voltage. + + reset-gpios: + maxItems: 1 + description: + Optional GPIO specifier for the touchscreen's reset pin + (active low). The line must be flagged with + GPIO_ACTIVE_LOW. + + wake-gpios: + maxItems: 1 + description: + Optional GPIO specifier for the touchscreen's wake pin + (active low). The line must be flagged with + GPIO_ACTIVE_LOW. + + linux,gpio-keymap: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + When enabled, the SPT_GPIOPWN_T19 object sends messages + on GPIO bit changes. An array of up to 8 entries can be provided + indicating the Linux keycode mapped to each bit of the status byte, + starting at the LSB. Linux keycodes are defined in + <dt-bindings/input/input.h>. + + Note: the numbering of the GPIOs and the bit they start at varies + between maXTouch devices. You must either refer to the documentation, + or experiment to determine which bit corresponds to which input. Use + KEY_RESERVED for unused padding values. + + atmel,wakeup-method: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The WAKE line is an active-low input that is used to wake up the touch + controller from deep-sleep mode before communication with the controller + could be started. This optional feature used to minimize current + consumption when the controller is in deep sleep mode. This feature is + relevant only to some controller families, like mXT1386 controller for + example. + + The WAKE pin can be connected in one of the following ways: + 1) left permanently low + 2) connected to the I2C-compatible SCL pin + 3) connected to a GPIO pin on the host + enum: + - 0 # ATMEL_MXT_WAKEUP_NONE + - 1 # ATMEL_MXT_WAKEUP_I2C_SCL + - 2 # ATMEL_MXT_WAKEUP_GPIO + default: 0 + + wakeup-source: + type: boolean + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/input/atmel-maxtouch.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + interrupt-parent = <&gpio>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + vdda-supply = <&ab8500_ldo_aux2_reg>; + vdd-supply = <&ab8500_ldo_aux5_reg>; + atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml b/Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml new file mode 100644 index 000000000..9ddba7f2e --- /dev/null +++ b/Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml @@ -0,0 +1,950 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/azoteq,iqs7222.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS7222A/B/C Capacitive Touch Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS7222A, IQS7222B and IQS7222C are multichannel capacitive touch + controllers that feature additional sensing capabilities. + + Link to datasheets: https://www.azoteq.com/ + +properties: + compatible: + enum: + - azoteq,iqs7222a + - azoteq,iqs7222b + - azoteq,iqs7222c + + reg: + maxItems: 1 + + irq-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low RDY output. + + reset-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low MCLR input. The + device is temporarily held in hardware reset prior to initialization if + this property is present. + + azoteq,max-counts: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the maximum number of conversion periods (counts) that can be + reported as follows: + 0: 1023 + 1: 2047 + 2: 4095 + 3: 16384 + + azoteq,auto-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the number of conversions to occur before an interrupt is + generated as follows: + 0: 4 + 1: 8 + 2: 16 + 3: 32 + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the preloaded ATI fine fractional divider. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the preloaded ATI coarse fractional divider. + + azoteq,ati-comp-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1023 + description: Specifies the preloaded ATI compensation selection. + + azoteq,lta-beta-lp: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the long-term average filter damping factor to be applied during + low-power mode. + + azoteq,lta-beta-np: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the long-term average filter damping factor to be applied during + normal-power mode. + + azoteq,counts-beta-lp: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the counts filter damping factor to be applied during low-power + mode. + + azoteq,counts-beta-np: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the counts filter damping factor to be applied during normal- + power mode. + + azoteq,lta-fast-beta-lp: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the long-term average filter fast damping factor to be applied + during low-power mode. + + azoteq,lta-fast-beta-np: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the long-term average filter fast damping factor to be applied + during normal-power mode. + + azoteq,timeout-ati-ms: + multipleOf: 500 + minimum: 0 + maximum: 32767500 + description: + Specifies the delay (in ms) before ATI is retried following an ATI error. + + azoteq,rate-ati-ms: + minimum: 0 + maximum: 65535 + description: Specifies the rate (in ms) at which ATI status is evaluated. + + azoteq,timeout-np-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the length of time (in ms) to wait for an event before moving + from normal-power mode to low-power mode. + + azoteq,rate-np-ms: + minimum: 0 + maximum: 3000 + description: Specifies the report rate (in ms) during normal-power mode. + + azoteq,timeout-lp-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the length of time (in ms) to wait for an event before moving + from low-power mode to ultra-low-power mode. + + azoteq,rate-lp-ms: + minimum: 0 + maximum: 3000 + description: Specifies the report rate (in ms) during low-power mode. + + azoteq,timeout-ulp-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the rate (in ms) at which channels not regularly sampled during + ultra-low-power mode are updated. + + azoteq,rate-ulp-ms: + minimum: 0 + maximum: 3000 + description: Specifies the report rate (in ms) during ultra-low-power mode. + +patternProperties: + "^cycle-[0-9]$": + type: object + description: Represents a conversion cycle serving two sensing channels. + + properties: + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the cycle's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the cycle's conversion frequency fraction. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 9 + items: + minimum: 0 + maximum: 8 + description: Specifies the CTx pin(s) associated with the cycle. + + azoteq,rx-float-inactive: + type: boolean + description: Floats any inactive CRx pins instead of grounding them. + + azoteq,dead-time-enable: + type: boolean + description: + Increases the denominator of the conversion frequency formula by one. + + azoteq,tx-freq-fosc: + type: boolean + description: + Fixes the conversion frequency to that of the device's core clock. + + azoteq,vbias-enable: + type: boolean + description: Enables the bias voltage for use during inductive sensing. + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the cycle's sensing mode as follows: + 0: None + 1: Self capacitive + 2: Mutual capacitive + 3: Inductive + + Note that in the case of IQS7222A, cycles 5 and 6 are restricted to + Hall-effect sensing. + + azoteq,iref-enable: + type: boolean + description: + Enables the current reference for use during various sensing modes. + + azoteq,iref-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the cycle's current reference level. + + azoteq,iref-trim: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the cycle's current reference trim. + + dependencies: + azoteq,iref-level: ["azoteq,iref-enable"] + azoteq,iref-trim: ["azoteq,iref-enable"] + + additionalProperties: false + + "^channel-([0-9]|1[0-9])$": + type: object + description: + Represents a single sensing channel. A channel is active if defined and + inactive otherwise. + + Note that in the case of IQS7222A, channels 10 and 11 are restricted to + Hall-effect sensing with events reported on channel 10 only. + + properties: + azoteq,ulp-allow: + type: boolean + description: + Permits the device to enter ultra-low-power mode while the channel + lies in a state of touch or proximity. + + azoteq,ref-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 9 + description: Specifies a separate reference channel to be followed. + + azoteq,ref-weight: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the relative weight of the reference channel. + + azoteq,use-prox: + type: boolean + description: + Activates the reference channel in response to proximity events + instead of touch events. + + azoteq,ati-band: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the channel's ATI band as a fraction of its ATI target as + follows: + 0: 1/16 + 1: 1/8 + 2: 1/4 + 3: 1/2 + + azoteq,global-halt: + type: boolean + description: + Specifies that the channel's long-term average is to freeze if any + other participating channel lies in a proximity or touch state. + + azoteq,invert-enable: + type: boolean + description: + Inverts the polarity of the states reported for proximity and touch + events relative to their respective thresholds. + + azoteq,dual-direction: + type: boolean + description: + Specifies that the channel's long-term average is to freeze in the + presence of either increasing or decreasing counts, thereby permit- + ting events to be reported in either direction. + + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 7 + description: Specifies the CRx pin(s) associated with the channel. + + azoteq,samp-cap-double: + type: boolean + description: Doubles the sampling capacitance from 40 pF to 80 pF. + + azoteq,vref-half: + type: boolean + description: Halves the discharge threshold from 1.0 V to 0.5 V. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the bias current applied during mutual (projected) + capacitive sensing as follows: + 0: 2 uA + 1: 5 uA + 2: 7 uA + 3: 10 uA + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 8 + minimum: 0 + maximum: 2040 + description: Specifies the channel's ATI target. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 16 + minimum: 0 + maximum: 496 + description: Specifies the channel's ATI base. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5] + description: | + Specifies the channel's ATI mode as follows: + 0: Disabled + 1: Compensation + 2: Compensation divider + 3: Fine fractional divider + 4: Coarse fractional divider + 5: Full + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the channel's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the channel's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the channel's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the channel's ATI compensation divider. + + azoteq,ati-comp-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1023 + description: Specifies the channel's ATI compensation selection. + + azoteq,debounce-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the channel's debounce entrance factor. + + azoteq,debounce-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the channel's debounce exit factor. + + patternProperties: + "^event-(prox|touch)$": + type: object + $ref: input.yaml# + description: + Represents a proximity or touch event reported by the channel. + + properties: + azoteq,gpio-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 3 + items: + minimum: 0 + maximum: 2 + description: | + Specifies one or more GPIO mapped to the event as follows: + 0: GPIO0 + 1: GPIO3 (IQS7222C only) + 2: GPIO4 (IQS7222C only) + + Note that although multiple events can be mapped to a single + GPIO, they must all be of the same type (proximity, touch or + slider gesture). + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Specifies the threshold for the event. Valid entries range from + 0-127 and 0-255 for proximity and touch events, respectively. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: + Specifies the hysteresis for the event (touch events only). + + azoteq,timeout-press-ms: + multipleOf: 500 + minimum: 0 + maximum: 127500 + description: + Specifies the length of time (in ms) to wait before automatically + releasing a press event. Specify zero to allow the press state to + persist indefinitely. + + The IQS7222B does not feature channel-specific timeouts; the time- + out specified for any one channel applies to all channels. + + linux,code: true + + linux,input-type: + enum: [1, 5] + default: 1 + description: + Specifies whether the event is to be interpreted as a key (1) + or a switch (5). + + additionalProperties: false + + dependencies: + azoteq,ref-weight: ["azoteq,ref-select"] + azoteq,use-prox: ["azoteq,ref-select"] + + additionalProperties: false + + "^slider-[0-1]$": + type: object + description: Represents a slider comprising three or four channels. + + properties: + azoteq,channel-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 4 + items: + minimum: 0 + maximum: 9 + description: + Specifies the order of the channels that participate in the slider. + + azoteq,slider-size: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 65535 + description: + Specifies the slider's one-dimensional resolution, equal to the + maximum coordinate plus one. + + azoteq,lower-cal: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the slider's lower starting point. + + azoteq,upper-cal: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the slider's upper starting point. + + azoteq,top-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: + Specifies the speed of movement after which coordinate filtering is + no longer applied. + + azoteq,bottom-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: + Specifies the speed of movement after which coordinate filtering is + linearly reduced. + + azoteq,bottom-beta: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: + Specifies the coordinate filter damping factor to be applied + while the speed of movement is below that which is specified + by azoteq,bottom-speed. + + azoteq,static-beta: + type: boolean + description: + Applies the coordinate filter damping factor specified by + azoteq,bottom-beta regardless of the speed of movement. + + azoteq,use-prox: + type: boolean + description: + Directs the slider to respond to the proximity states of the selected + channels instead of their corresponding touch states. Note the slider + cannot report granular coordinates during a state of proximity. + + linux,axis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Specifies the absolute axis to which coordinates are mapped. Specify + ABS_WHEEL to operate the slider as a wheel (IQS7222C only). + + patternProperties: + "^event-(press|tap|(swipe|flick)-(pos|neg))$": + type: object + $ref: input.yaml# + description: + Represents a press or gesture (IQS7222A only) event reported by + the slider. + + properties: + linux,code: true + + azoteq,gesture-max-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + description: + Specifies the length of time (in ms) within which a tap, swipe + or flick gesture must be completed in order to be acknowledged + by the device. The number specified for any one swipe or flick + gesture applies to all remaining swipe or flick gestures. + + azoteq,gesture-min-ms: + multipleOf: 16 + minimum: 0 + maximum: 496 + description: + Specifies the length of time (in ms) for which a tap gesture must + be held in order to be acknowledged by the device. + + azoteq,gesture-dist: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 16 + minimum: 0 + maximum: 4080 + description: + Specifies the distance across which a swipe or flick gesture must + travel in order to be acknowledged by the device. The number spec- + ified for any one swipe or flick gesture applies to all remaining + swipe or flick gestures. + + azoteq,gpio-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 3 + items: + minimum: 0 + maximum: 2 + description: | + Specifies one or more GPIO mapped to the event as follows: + 0: GPIO0 + 1: GPIO3 (IQS7222C only) + 2: GPIO4 (IQS7222C only) + + Note that although multiple events can be mapped to a single + GPIO, they must all be of the same type (proximity, touch or + slider gesture). + + additionalProperties: false + + required: + - azoteq,channel-select + + additionalProperties: false + + "^gpio-[0-2]$": + type: object + description: | + Represents a GPIO mapped to one or more events as follows: + gpio-0: GPIO0 + gpio-1: GPIO3 (IQS7222C only) + gpio-2: GPIO4 (IQS7222C only) + + allOf: + - $ref: ../pinctrl/pincfg-node.yaml# + + properties: + drive-open-drain: true + + additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: azoteq,iqs7222b + + then: + patternProperties: + "^cycle-[0-9]$": + properties: + azoteq,iref-enable: false + + "^channel-([0-9]|1[0-9])$": + properties: + azoteq,ref-select: false + + patternProperties: + "^event-(prox|touch)$": + properties: + azoteq,gpio-select: false + + "^slider-[0-1]$": false + + "^gpio-[0-2]$": false + + - if: + properties: + compatible: + contains: + const: azoteq,iqs7222a + + then: + patternProperties: + "^channel-([0-9]|1[0-9])$": + patternProperties: + "^event-(prox|touch)$": + properties: + azoteq,gpio-select: + maxItems: 1 + items: + maximum: 0 + + "^slider-[0-1]$": + properties: + azoteq,slider-size: + multipleOf: 16 + minimum: 16 + maximum: 4080 + + azoteq,top-speed: + multipleOf: 4 + maximum: 1020 + + patternProperties: + "^event-(press|tap|(swipe|flick)-(pos|neg))$": + properties: + azoteq,gpio-select: + maxItems: 1 + items: + maximum: 0 + + else: + patternProperties: + "^channel-([0-9]|1[0-9])$": + properties: + azoteq,ulp-allow: false + + "^slider-[0-1]$": + patternProperties: + "^event-(press|tap|(swipe|flick)-(pos|neg))$": + properties: + azoteq,gesture-max-ms: false + + azoteq,gesture-min-ms: false + + azoteq,gesture-dist: false + +required: + - compatible + - reg + - irq-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/input/input.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + iqs7222a@44 { + compatible = "azoteq,iqs7222a"; + reg = <0x44>; + irq-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + azoteq,lta-beta-lp = <7>; + azoteq,lta-beta-np = <8>; + azoteq,counts-beta-lp = <2>; + azoteq,counts-beta-np = <3>; + azoteq,lta-fast-beta-lp = <3>; + azoteq,lta-fast-beta-np = <4>; + + cycle-0 { + azoteq,conv-period = <5>; + azoteq,conv-frac = <127>; + azoteq,tx-enable = <1>, <2>, <4>, <5>; + azoteq,dead-time-enable; + azoteq,sense-mode = <2>; + }; + + cycle-1 { + azoteq,conv-period = <5>; + azoteq,conv-frac = <127>; + azoteq,tx-enable = <5>; + azoteq,dead-time-enable; + azoteq,sense-mode = <2>; + }; + + cycle-2 { + azoteq,conv-period = <5>; + azoteq,conv-frac = <127>; + azoteq,tx-enable = <4>; + azoteq,dead-time-enable; + azoteq,sense-mode = <2>; + }; + + cycle-3 { + azoteq,conv-period = <5>; + azoteq,conv-frac = <127>; + azoteq,tx-enable = <2>; + azoteq,dead-time-enable; + azoteq,sense-mode = <2>; + }; + + cycle-4 { + azoteq,conv-period = <5>; + azoteq,conv-frac = <127>; + azoteq,tx-enable = <1>; + azoteq,dead-time-enable; + azoteq,sense-mode = <2>; + }; + + cycle-5 { + azoteq,conv-period = <2>; + azoteq,conv-frac = <0>; + }; + + cycle-6 { + azoteq,conv-period = <2>; + azoteq,conv-frac = <0>; + }; + + channel-0 { + azoteq,ulp-allow; + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <3>; + azoteq,ati-target = <800>; + azoteq,ati-base = <208>; + azoteq,ati-mode = <5>; + }; + + channel-1 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <3>; + azoteq,ati-target = <496>; + azoteq,ati-base = <208>; + azoteq,ati-mode = <5>; + }; + + channel-2 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <3>; + azoteq,ati-target = <496>; + azoteq,ati-base = <208>; + azoteq,ati-mode = <5>; + }; + + channel-3 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <3>; + azoteq,ati-target = <496>; + azoteq,ati-base = <208>; + azoteq,ati-mode = <5>; + }; + + channel-4 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <3>; + azoteq,ati-target = <496>; + azoteq,ati-base = <208>; + azoteq,ati-mode = <5>; + }; + + channel-5 { + azoteq,ulp-allow; + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <6>; + azoteq,ati-target = <800>; + azoteq,ati-base = <144>; + azoteq,ati-mode = <5>; + }; + + channel-6 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <6>; + azoteq,ati-target = <496>; + azoteq,ati-base = <160>; + azoteq,ati-mode = <5>; + + event-touch { + linux,code = <KEY_MUTE>; + }; + }; + + channel-7 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <6>; + azoteq,ati-target = <496>; + azoteq,ati-base = <160>; + azoteq,ati-mode = <5>; + + event-touch { + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + + channel-8 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <6>; + azoteq,ati-target = <496>; + azoteq,ati-base = <160>; + azoteq,ati-mode = <5>; + + event-touch { + linux,code = <KEY_VOLUMEUP>; + }; + }; + + channel-9 { + azoteq,global-halt; + azoteq,invert-enable; + azoteq,rx-enable = <6>; + azoteq,ati-target = <496>; + azoteq,ati-base = <160>; + azoteq,ati-mode = <5>; + + event-touch { + linux,code = <KEY_POWER>; + }; + }; + + channel-10 { + azoteq,ulp-allow; + azoteq,ati-target = <496>; + azoteq,ati-base = <112>; + + event-touch { + linux,code = <SW_LID>; + linux,input-type = <EV_SW>; + }; + }; + + channel-11 { + azoteq,ati-target = <496>; + azoteq,ati-base = <112>; + }; + + slider-0 { + azoteq,channel-select = <1>, <2>, <3>, <4>; + azoteq,slider-size = <4080>; + azoteq,upper-cal = <50>; + azoteq,lower-cal = <30>; + azoteq,top-speed = <200>; + azoteq,bottom-speed = <1>; + azoteq,bottom-beta = <3>; + + event-tap { + linux,code = <KEY_PLAYPAUSE>; + azoteq,gesture-max-ms = <400>; + azoteq,gesture-min-ms = <32>; + }; + + event-flick-pos { + linux,code = <KEY_NEXTSONG>; + azoteq,gesture-max-ms = <800>; + azoteq,gesture-dist = <800>; + }; + + event-flick-neg { + linux,code = <KEY_PREVIOUSSONG>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt new file mode 100644 index 000000000..262deab73 --- /dev/null +++ b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt @@ -0,0 +1,107 @@ +* Broadcom Keypad Controller device tree bindings + +Broadcom Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be "brcm,bcm-keypad" + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Board Specific Properties: +- keypad,num-rows: Number of row lines connected to the keypad + controller. + +- keypad,num-columns: Number of column lines connected to the + keypad controller. + +- col-debounce-filter-period: The debounce period for the Column filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- status-debounce-filter-period: The debounce period for the Status filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- row-output-enabled: An optional property indicating whether the row or + column is being used as output. If specified the row is being used + as the output. Else defaults to column. + +- pull-up-enabled: An optional property indicating the Keypad scan mode. + If specified implies the keypad scan pull-up has been enabled. + +- autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem (optional). + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +Example: +#include "dt-bindings/input/input.h" + +/ { + keypad: keypad@180ac000 { + /* Required SoC specific properties */ + compatible = "brcm,bcm-keypad"; + + /* Required Board specific properties */ + keypad,num-rows = <5>; + keypad,num-columns = <5>; + + linux,keymap = <MATRIX_KEY(0x00, 0x02, KEY_F) /* key_forward */ + MATRIX_KEY(0x00, 0x03, KEY_HOME) /* key_home */ + MATRIX_KEY(0x00, 0x04, KEY_M) /* key_message */ + MATRIX_KEY(0x01, 0x00, KEY_A) /* key_contacts */ + MATRIX_KEY(0x01, 0x01, KEY_1) /* key_1 */ + MATRIX_KEY(0x01, 0x02, KEY_2) /* key_2 */ + MATRIX_KEY(0x01, 0x03, KEY_3) /* key_3 */ + MATRIX_KEY(0x01, 0x04, KEY_S) /* key_speaker */ + MATRIX_KEY(0x02, 0x00, KEY_P) /* key_phone */ + MATRIX_KEY(0x02, 0x01, KEY_4) /* key_4 */ + MATRIX_KEY(0x02, 0x02, KEY_5) /* key_5 */ + MATRIX_KEY(0x02, 0x03, KEY_6) /* key_6 */ + MATRIX_KEY(0x02, 0x04, KEY_VOLUMEUP) /* key_vol_up */ + MATRIX_KEY(0x03, 0x00, KEY_C) /* key_call_log */ + MATRIX_KEY(0x03, 0x01, KEY_7) /* key_7 */ + MATRIX_KEY(0x03, 0x02, KEY_8) /* key_8 */ + MATRIX_KEY(0x03, 0x03, KEY_9) /* key_9 */ + MATRIX_KEY(0x03, 0x04, KEY_VOLUMEDOWN) /* key_vol_down */ + MATRIX_KEY(0x04, 0x00, KEY_H) /* key_headset */ + MATRIX_KEY(0x04, 0x01, KEY_KPASTERISK) /* key_* */ + MATRIX_KEY(0x04, 0x02, KEY_0) /* key_0 */ + MATRIX_KEY(0x04, 0x03, KEY_GRAVE) /* key_# */ + MATRIX_KEY(0x04, 0x04, KEY_MUTE) /* key_mute */ + >; + + /* Optional board specific properties */ + col-debounce-filter-period = <5>; + row-output-enabled; + pull-up-enabled; + + }; +}; diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt new file mode 100644 index 000000000..3eed8819d --- /dev/null +++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt @@ -0,0 +1,27 @@ +* Cirrus Logic CLPS711X matrix keypad device tree bindings + +Required Properties: +- compatible: Shall contain "cirrus,ep7209-keypad". +- row-gpios: List of GPIOs used as row lines. +- poll-interval: Poll interval time in milliseconds. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt. + +Optional Properties: +- autorepeat: Enable autorepeat feature. + +Example: + keypad { + compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad"; + autorepeat; + poll-interval = <120>; + row-gpios = <&porta 0 0>, + <&porta 1 0>; + + linux,keymap = < + MATRIX_KEY(0, 0, KEY_UP) + MATRIX_KEY(0, 1, KEY_DOWN) + MATRIX_KEY(1, 0, KEY_LEFT) + MATRIX_KEY(1, 1, KEY_RIGHT) + >; + }; diff --git a/Documentation/devicetree/bindings/input/cpcap-pwrbutton.txt b/Documentation/devicetree/bindings/input/cpcap-pwrbutton.txt new file mode 100644 index 000000000..0dd0076da --- /dev/null +++ b/Documentation/devicetree/bindings/input/cpcap-pwrbutton.txt @@ -0,0 +1,20 @@ +Motorola CPCAP on key + +This module is part of the CPCAP. For more details about the whole +chip see Documentation/devicetree/bindings/mfd/motorola-cpcap.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "motorola,cpcap-pwrbutton" +- interrupts: irq specifier for CPCAP's ON IRQ + +Example: + +&cpcap { + cpcap_pwrbutton: pwrbutton { + compatible = "motorola,cpcap-pwrbutton"; + interrupts = <23 IRQ_TYPE_NONE>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt new file mode 100644 index 000000000..d3db65916 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -0,0 +1,42 @@ +Cypress I2C Touchpad + +Required properties: +- compatible: must be "cypress,cyapa". +- reg: I2C address of the chip. +- interrupts: interrupt to which the chip is connected (see interrupt + binding[0]). + +Optional properties: +- wakeup-source: touchpad can be used as a wakeup source. +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the device (see + pinctrl binding [1]). +- vcc-supply: a phandle for the regulator supplying 3.3V power. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + &i2c0 { + /* ... */ + + /* Cypress Gen3 touchpad */ + touchpad@67 { + compatible = "cypress,cyapa"; + reg = <0x67>; + interrupt-parent = <&gpio>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ + wakeup-source; + }; + + /* Cypress Gen5 and later touchpad */ + touchpad@24 { + compatible = "cypress,cyapa"; + reg = <0x24>; + interrupt-parent = <&gpio>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ + wakeup-source; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.yaml b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.yaml new file mode 100644 index 000000000..52dca8b64 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/cypress,tm2-touchkey.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung TM2 touch key controller + +maintainers: + - Stephan Gerhold <stephan@gerhold.net> + +description: | + Touch key controllers similar to the TM2 can be found in a wide range of + Samsung devices. They are implemented using many different MCUs, but use + a similar I2C protocol. + +allOf: + - $ref: input.yaml# + +properties: + compatible: + enum: + - cypress,tm2-touchkey + - cypress,midas-touchkey + - cypress,aries-touchkey + - coreriver,tc360-touchkey + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: + description: Optional regulator for LED voltage, 3.3V. + + vcc-supply: + description: Optional regulator for MCU, 1.8V-3.3V (depending on MCU). + + vddio-supply: + description: | + Optional regulator that provides digital I/O voltage, + e.g. for pulling up the interrupt line or the I2C pins. + + linux,keycodes: + minItems: 1 + maxItems: 4 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchkey@20 { + compatible = "cypress,tm2-touchkey"; + reg = <0x20>; + interrupt-parent = <&gpa3>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + vcc-supply = <&ldo32_reg>; + vdd-supply = <&ldo33_reg>; + linux,keycodes = <KEY_MENU KEY_BACK>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/cypress-sf.yaml b/Documentation/devicetree/bindings/input/cypress-sf.yaml new file mode 100644 index 000000000..c0b051466 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cypress-sf.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/cypress-sf.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cypress StreetFighter touchkey controller + +maintainers: + - Yassine Oudjana <y.oudjana@protonmail.com> + +allOf: + - $ref: input.yaml# + +properties: + compatible: + const: cypress,sf3155 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + avdd-supply: + description: Regulator for AVDD analog voltage + + vdd-supply: + description: Regulator for VDD digital voltage + + linux,keycodes: + minItems: 1 + maxItems: 8 + +required: + - compatible + - reg + - interrupts + - avdd-supply + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchkey@28 { + compatible = "cypress,sf3155"; + reg = <0x28>; + interrupt-parent = <&msmgpio>; + interrupts = <77 IRQ_TYPE_EDGE_FALLING>; + avdd-supply = <&vreg_l6a_1p8>; + vdd-supply = <&vdd_3v2_tp>; + linux,keycodes = <KEY_BACK KEY_MENU>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/da9062-onkey.txt b/Documentation/devicetree/bindings/input/da9062-onkey.txt new file mode 100644 index 000000000..e5eef59a9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/da9062-onkey.txt @@ -0,0 +1,47 @@ +* Dialog DA9061/62/63 OnKey Module + +This module is part of the DA9061/DA9062/DA9063. For more details about entire +DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt +For DA9063 see Documentation/devicetree/bindings/mfd/dlg,da9063.yaml + +This module provides the KEY_POWER event. + +Required properties: + +- compatible: should be one of the following valid compatible string lines: + "dlg,da9061-onkey", "dlg,da9062-onkey" + "dlg,da9062-onkey" + "dlg,da9063-onkey" + +Optional properties: + +- dlg,disable-key-power : Disable power-down using a long key-press. If this + entry exists the OnKey driver will remove support for the KEY_POWER key + press when triggered using a long press of the OnKey. + +Example: DA9063 + + pmic0: da9063@58 { + onkey { + compatible = "dlg,da9063-onkey"; + dlg,disable-key-power; + }; + }; + +Example: DA9062 + + pmic0: da9062@58 { + onkey { + compatible = "dlg,da9062-onkey"; + dlg,disable-key-power; + }; + }; + +Example: DA9061 using a fall-back compatible for the DA9062 onkey driver + + pmic0: da9061@58 { + onkey { + compatible = "dlg,da9061-onkey", "dlg,da9062-onkey"; + dlg,disable-key-power; + }; + }; diff --git a/Documentation/devicetree/bindings/input/dlg,da7280.txt b/Documentation/devicetree/bindings/input/dlg,da7280.txt new file mode 100644 index 000000000..96ee5d50e --- /dev/null +++ b/Documentation/devicetree/bindings/input/dlg,da7280.txt @@ -0,0 +1,108 @@ +Dialog Semiconductor DA7280 Haptics bindings + +Required properties: +- compatible: Should be "dlg,da7280". +- reg: Specifies the I2C slave address. + +- interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from DA7280 are delivered to. + +- dlg,actuator-type: Set Actuator type. it should be one of: + "LRA" - Linear Resonance Actuator type. + "ERM-bar" - Bar type Eccentric Rotating Mass. + "ERM-coin" - Coin type Eccentric Rotating Mass. + +- dlg,const-op-mode: Haptic operation mode for FF_CONSTANT. + Possible values: + 1 - Direct register override(DRO) mode triggered by i2c(default), + 2 - PWM data source mode controlled by PWM duty, +- dlg,periodic-op-mode: Haptic operation mode for FF_PERIODIC. + Possible values: + 1 - Register triggered waveform memory(RTWM) mode, the pattern + assigned to the PS_SEQ_ID played as much times as PS_SEQ_LOOP, + 2 - Edge triggered waveform memory(ETWM) mode, external GPI(N) + control are required to enable/disable and it needs to keep + device enabled by sending magnitude (X > 0), + the pattern is assigned to the GPI(N)_SEQUENCE_ID below. + The default value is 1 for both of the operation modes. + For more details, please see the datasheet. + +- dlg,nom-microvolt: Nominal actuator voltage rating. + Valid values: 0 - 6000000. +- dlg,abs-max-microvolt: Absolute actuator maximum voltage rating. + Valid values: 0 - 6000000. +- dlg,imax-microamp: Actuator max current rating. + Valid values: 0 - 252000. + Default: 130000. +- dlg,impd-micro-ohms: the impedance of the actuator in micro ohms. + Valid values: 0 - 1500000000. + +Optional properties: +- pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + (See Documentation/devicetree/bindings/pwm/pwm.txt + for further information relating to pwm properties) + +- dlg,ps-seq-id: the PS_SEQ_ID(pattern ID in waveform memory inside chip) + to play back when RTWM-MODE is enabled. + Valid range: 0 - 15. +- dlg,ps-seq-loop: the PS_SEQ_LOOP, Number of times the pre-stored sequence + pointed to by PS_SEQ_ID or GPI(N)_SEQUENCE_ID is repeated. + Valid range: 0 - 15. +- dlg,gpiN-seq-id: the GPI(N)_SEQUENCE_ID, pattern to play + when gpi0 is triggered, 'N' must be 0 - 2. + Valid range: 0 - 15. +- dlg,gpiN-mode: the pattern mode which can select either + "Single-pattern" or "Multi-pattern", 'N' must be 0 - 2. +- dlg,gpiN-polarity: gpiN polarity which can be chosen among + "Rising-edge", "Falling-edge" and "Both-edge", + 'N' must be 0 - 2 + Haptic will work by this edge option in case of ETWM mode. + +- dlg,resonant-freq-hz: use in case of LRA. + the frequency range: 50 - 300. + Default: 205. + +- dlg,bemf-sens-enable: Enable for internal loop computations. +- dlg,freq-track-enable: Enable for resonant frequency tracking. +- dlg,acc-enable: Enable for active acceleration. +- dlg,rapid-stop-enable: Enable for rapid stop. +- dlg,amp-pid-enable: Enable for the amplitude PID. +- dlg,mem-array: Customized waveform memory(patterns) data downloaded to + the device during initialization. This is an array of 100 values(u8). + +For further information, see device datasheet. + +====== + +Example: + + haptics: da7280-haptics@4a { + compatible = "dlg,da7280"; + reg = <0x4a>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + dlg,actuator-type = "LRA"; + dlg,dlg,const-op-mode = <1>; + dlg,dlg,periodic-op-mode = <1>; + dlg,nom-microvolt = <2000000>; + dlg,abs-max-microvolt = <2000000>; + dlg,imax-microamp = <170000>; + dlg,resonant-freq-hz = <180>; + dlg,impd-micro-ohms = <10500000>; + dlg,freq-track-enable; + dlg,rapid-stop-enable; + dlg,mem-array = < + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 + >; + }; diff --git a/Documentation/devicetree/bindings/input/dlink,dir685-touchkeys.txt b/Documentation/devicetree/bindings/input/dlink,dir685-touchkeys.txt new file mode 100644 index 000000000..10dec1c57 --- /dev/null +++ b/Documentation/devicetree/bindings/input/dlink,dir685-touchkeys.txt @@ -0,0 +1,21 @@ +* D-Link DIR-685 Touchkeys + +This is a I2C one-off touchkey controller based on the Cypress Semiconductor +CY8C214 MCU with some firmware in its internal 8KB flash. The circuit +board inside the router is named E119921. + +The touchkey device node should be placed inside an I2C bus node. + +Required properties: +- compatible: must be "dlink,dir685-touchkeys" +- reg: the I2C address of the touchkeys +- interrupts: reference to the interrupt number + +Example: + +touchkeys@26 { + compatible = "dlink,dir685-touchkeys"; + reg = <0x26>; + interrupt-parent = <&gpio0>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/input/e3x0-button.txt b/Documentation/devicetree/bindings/input/e3x0-button.txt new file mode 100644 index 000000000..907b195f2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/e3x0-button.txt @@ -0,0 +1,23 @@ +National Instruments Ettus Research USRP E3x0 button driver + +This module is part of the NI Ettus Research USRP E3x0 SDR. + +This module provides a simple power button event via two interrupts. + +Required properties: +- compatible: should be one of the following + - "ettus,e3x0-button": For devices such as the NI Ettus Research USRP E3x0 +- interrupts: should be one of the following + - <0 30 1>, <0 31 1>: For devices such as the NI Ettus Research USRP E3x0 +- interrupt-names: should be one of the following + - "press", "release": For devices such as the NI Ettus Research USRP E3x0 + +Note: Interrupt numbers might vary depending on the FPGA configuration. + +Example: + button { + compatible = "ettus,e3x0-button"; + interrupt-parent = <&intc>; + interrupts = <0 30 1>, <0 31 1>; + interrupt-names = "press", "release"; + } diff --git a/Documentation/devicetree/bindings/input/elan,ekth3000.yaml b/Documentation/devicetree/bindings/input/elan,ekth3000.yaml new file mode 100644 index 000000000..2a9bb6ace --- /dev/null +++ b/Documentation/devicetree/bindings/input/elan,ekth3000.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/elan,ekth3000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Elantech I2C Touchpad + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen/touchscreen.yaml# + +properties: + compatible: + const: elan,ekth3000 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + wakeup-source: + type: boolean + description: touchpad can be used as a wakeup source + + vcc-supply: + description: a phandle for the regulator supplying 3.3V power + + elan,trackpoint: + type: boolean + description: touchpad can support a trackpoint + + elan,clickpad: + type: boolean + description: touchpad is a clickpad (the entire surface is a button) + + elan,middle-button: + type: boolean + description: touchpad has a physical middle button + + elan,x_traces: + $ref: /schemas/types.yaml#/definitions/uint32 + description: number of antennas on the x axis + + elan,y_traces: + $ref: /schemas/types.yaml#/definitions/uint32 + description: number of antennas on the y axis + + touchscreen-size-x: true + + touchscreen-size-y: true + + touchscreen-x-mm: true + + touchscreen-y-mm: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/input/elan,ekth6915.yaml b/Documentation/devicetree/bindings/input/elan,ekth6915.yaml new file mode 100644 index 000000000..05e6f2df6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/elan,ekth6915.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/elan,ekth6915.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Elan eKTH6915 touchscreen controller + +maintainers: + - Douglas Anderson <dianders@chromium.org> + +description: + Supports the Elan eKTH6915 touchscreen controller. + This touchscreen controller uses the i2c-hid protocol with a reset GPIO. + +properties: + compatible: + items: + - const: elan,ekth6915 + + reg: + const: 0x10 + + interrupts: + maxItems: 1 + + reset-gpios: + description: Reset GPIO; not all touchscreens using eKTH6915 hook this up. + + vcc33-supply: + description: The 3.3V supply to the touchscreen. + + vccio-supply: + description: + The IO supply to the touchscreen. Need not be specified if this is the + same as the 3.3V supply. + +required: + - compatible + - reg + - interrupts + - vcc33-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ap_ts: touchscreen@10 { + compatible = "elan,ekth6915"; + reg = <0x10>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + vcc33-supply = <&pp3300_ts>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml b/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml new file mode 100644 index 000000000..5139af287 --- /dev/null +++ b/Documentation/devicetree/bindings/input/fsl,mpr121-touchkey.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/fsl,mpr121-touchkey.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MPR121 capacitive touch sensor controller + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +description: | + The MPR121 supports up to 12 completely independent electrodes/capacitance + sensing inputs in which 8 are multifunctional for LED driving and GPIO. + https://www.nxp.com/docs/en/data-sheet/MPR121.pdf + +allOf: + - $ref: input.yaml# + +anyOf: + - required: [ interrupts ] + - required: [ poll-interval ] + +properties: + compatible: + const: fsl,mpr121-touchkey + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: true + + linux,keycodes: + minItems: 1 + maxItems: 12 + + wakeup-source: + description: Use any event on keypad as wakeup event. + type: boolean + +required: + - compatible + - reg + - vdd-supply + - linux,keycodes + +unevaluatedProperties: false + +examples: + - | + // Example with interrupts + #include "dt-bindings/input/input.h" + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchkey@5a { + compatible = "fsl,mpr121-touchkey"; + reg = <0x5a>; + interrupt-parent = <&gpio1>; + interrupts = <28 2>; + autorepeat; + vdd-supply = <&ldo4_reg>; + linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, + <KEY_4>, <KEY_5>, <KEY_6>, <KEY_7>, + <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; + }; + }; + + - | + // Example with polling + #include "dt-bindings/input/input.h" + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchkey@5a { + compatible = "fsl,mpr121-touchkey"; + reg = <0x5a>; + poll-interval = <20>; + autorepeat; + vdd-supply = <&ldo4_reg>; + linux,keycodes = <KEY_0>, <KEY_1>, <KEY_2>, <KEY_3>, + <KEY_4>, <KEY_5>, <KEY_6>, <KEY_7>, + <KEY_8>, <KEY_9>, <KEY_A>, <KEY_B>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/fsl,scu-key.yaml b/Documentation/devicetree/bindings/input/fsl,scu-key.yaml new file mode 100644 index 000000000..e6266d188 --- /dev/null +++ b/Documentation/devicetree/bindings/input/fsl,scu-key.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/fsl,scu-key.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX SCU Client Device Node - SCU key bindings based on SCU Message Protocol + +maintainers: + - Dong Aisheng <aisheng.dong@nxp.com> + +description: i.MX SCU Client Device Node + Client nodes are maintained as children of the relevant IMX-SCU device node. + +allOf: + - $ref: input.yaml# + +properties: + compatible: + items: + - const: fsl,imx8qxp-sc-key + - const: fsl,imx-sc-key + + linux,keycodes: + maxItems: 1 + +required: + - compatible + - linux,keycodes + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + + keys { + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; + linux,keycodes = <KEY_POWER>; + }; diff --git a/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml b/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml new file mode 100644 index 000000000..1c191bc5a --- /dev/null +++ b/Documentation/devicetree/bindings/input/goodix,gt7375p.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/goodix,gt7375p.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Goodix GT7375P touchscreen + +maintainers: + - Douglas Anderson <dianders@chromium.org> + +description: + Supports the Goodix GT7375P touchscreen. + This touchscreen uses the i2c-hid protocol but has some non-standard + power sequencing required. + +properties: + compatible: + oneOf: + - const: goodix,gt7375p + - items: + - const: goodix,gt7986u + - const: goodix,gt7375p + + reg: + enum: + - 0x5d + - 0x14 + + interrupts: + maxItems: 1 + + reset-gpios: + true + + vdd-supply: + description: The 3.3V supply to the touchscreen. + +required: + - compatible + - reg + - interrupts + - reset-gpios + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ap_ts: touchscreen@5d { + compatible = "goodix,gt7375p"; + reg = <0x5d>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + vdd-supply = <&pp3300_ts>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/google,cros-ec-keyb.yaml b/Documentation/devicetree/bindings/input/google,cros-ec-keyb.yaml new file mode 100644 index 000000000..e05690b3e --- /dev/null +++ b/Documentation/devicetree/bindings/input/google,cros-ec-keyb.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/input/google,cros-ec-keyb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ChromeOS EC Keyboard + +maintainers: + - Simon Glass <sjg@chromium.org> + - Benson Leung <bleung@chromium.org> + +description: | + Google's ChromeOS EC Keyboard is a simple matrix keyboard + implemented on a separate EC (Embedded Controller) device. It provides + a message for reading key scans from the EC. These are then converted + into keycodes for processing by the kernel. This device also supports + switches/buttons like power and volume buttons. + +properties: + compatible: + oneOf: + - description: ChromeOS EC with only buttons/switches + const: google,cros-ec-keyb-switches + - description: ChromeOS EC with keyboard and possibly buttons/switches + const: google,cros-ec-keyb + + google,needs-ghost-filter: + description: + Enable a ghost filter for the matrix keyboard. This is recommended + if the EC does not have its own logic or hardware for this. + type: boolean + + function-row-physmap: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 15 + description: | + An ordered u32 array describing the rows/columns (in the scan matrix) + of top row keys from physical left (KEY_F1) to right. Each entry + encodes the row/column as: + (((row) & 0xFF) << 24) | (((column) & 0xFF) << 16) + where the lower 16 bits are reserved. This property is specified only + when the keyboard has a custom design for the top row keys. + +dependencies: + function-row-phsymap: [ 'linux,keymap' ] + google,needs-ghost-filter: [ 'linux,keymap' ] + +required: + - compatible + +if: + properties: + compatible: + contains: + const: google,cros-ec-keyb +then: + $ref: "/schemas/input/matrix-keymap.yaml#" + required: + - keypad,num-rows + - keypad,num-columns + - linux,keymap + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + keyboard-controller { + compatible = "google,cros-ec-keyb"; + keypad,num-rows = <8>; + keypad,num-columns = <13>; + google,needs-ghost-filter; + function-row-physmap = < + MATRIX_KEY(0x00, 0x02, 0) /* T1 */ + MATRIX_KEY(0x03, 0x02, 0) /* T2 */ + MATRIX_KEY(0x02, 0x02, 0) /* T3 */ + MATRIX_KEY(0x01, 0x02, 0) /* T4 */ + MATRIX_KEY(0x03, 0x04, 0) /* T5 */ + MATRIX_KEY(0x02, 0x04, 0) /* T6 */ + MATRIX_KEY(0x01, 0x04, 0) /* T7 */ + MATRIX_KEY(0x02, 0x09, 0) /* T8 */ + MATRIX_KEY(0x01, 0x09, 0) /* T9 */ + MATRIX_KEY(0x00, 0x04, 0) /* T10 */ + >; + /* + * Keymap entries take the form of 0xRRCCKKKK where + * RR=Row CC=Column KKKK=Key Code + * The values below are for a US keyboard layout and + * are taken from the Linux driver. Note that the + * 102ND key is not used for US keyboards. + */ + linux,keymap = < + /* CAPSLCK F1 B F10 */ + 0x0001003a 0x0002003b 0x00030030 0x00040044 + /* N = R_ALT ESC */ + 0x00060031 0x0008000d 0x000a0064 0x01010001 + /* F4 G F7 H */ + 0x0102003e 0x01030022 0x01040041 0x01060023 + /* ' F9 BKSPACE L_CTRL */ + 0x01080028 0x01090043 0x010b000e 0x0200001d + /* TAB F3 T F6 */ + 0x0201000f 0x0202003d 0x02030014 0x02040040 + /* ] Y 102ND [ */ + 0x0205001b 0x02060015 0x02070056 0x0208001a + /* F8 GRAVE F2 5 */ + 0x02090042 0x03010029 0x0302003c 0x03030006 + /* F5 6 - \ */ + 0x0304003f 0x03060007 0x0308000c 0x030b002b + /* R_CTRL A D F */ + 0x04000061 0x0401001e 0x04020020 0x04030021 + /* S K J ; */ + 0x0404001f 0x04050025 0x04060024 0x04080027 + /* L ENTER Z C */ + 0x04090026 0x040b001c 0x0501002c 0x0502002e + /* V X , M */ + 0x0503002f 0x0504002d 0x05050033 0x05060032 + /* L_SHIFT / . SPACE */ + 0x0507002a 0x05080035 0x05090034 0x050B0039 + /* 1 3 4 2 */ + 0x06010002 0x06020004 0x06030005 0x06040003 + /* 8 7 0 9 */ + 0x06050009 0x06060008 0x0608000b 0x0609000a + /* L_ALT DOWN RIGHT Q */ + 0x060a0038 0x060b006c 0x060c006a 0x07010010 + /* E R W I */ + 0x07020012 0x07030013 0x07040011 0x07050017 + /* U R_SHIFT P O */ + 0x07060016 0x07070036 0x07080019 0x07090018 + /* UP LEFT */ + 0x070b0067 0x070c0069>; + }; + - | + /* No matrix keyboard, just buttons/switches */ + keyboard-controller { + compatible = "google,cros-ec-keyb-switches"; + }; +... diff --git a/Documentation/devicetree/bindings/input/gpio-beeper.txt b/Documentation/devicetree/bindings/input/gpio-beeper.txt new file mode 100644 index 000000000..a5086e37f --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-beeper.txt @@ -0,0 +1,13 @@ +* GPIO beeper device tree bindings + +Register a beeper connected to GPIO pin. + +Required properties: +- compatible: Should be "gpio-beeper". +- gpios: From common gpio binding; gpio connection to beeper enable pin. + +Example: + beeper: beeper { + compatible = "gpio-beeper"; + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-decoder.txt b/Documentation/devicetree/bindings/input/gpio-decoder.txt new file mode 100644 index 000000000..14a77fb96 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-decoder.txt @@ -0,0 +1,23 @@ +* GPIO Decoder DT bindings + +Required Properties: +- compatible: should be "gpio-decoder" +- gpios: a spec of gpios (at least two) to be decoded to a number with + first entry representing the MSB. + +Optional Properties: +- decoder-max-value: Maximum possible value that can be reported by + the gpios. +- linux,axis: the input subsystem axis to map to (ABS_X/ABS_Y). + Defaults to 0 (ABS_X). + +Example: + gpio-decoder0 { + compatible = "gpio-decoder"; + gpios = <&pca9536 3 GPIO_ACTIVE_HIGH>, + <&pca9536 2 GPIO_ACTIVE_HIGH>, + <&pca9536 1 GPIO_ACTIVE_HIGH>, + <&pca9536 0 GPIO_ACTIVE_HIGH>; + linux,axis = <0>; /* ABS_X */ + decoder-max-value = <9>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.yaml b/Documentation/devicetree/bindings/input/gpio-keys.yaml new file mode 100644 index 000000000..17ac9dff7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-keys.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/gpio-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Device-Tree bindings for GPIO attached keys + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + compatible: + enum: + - gpio-keys + - gpio-keys-polled + + autorepeat: true + + label: + description: Name of entire device + + poll-interval: true + +patternProperties: + "^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$": + $ref: input.yaml# + + properties: + gpios: + maxItems: 1 + + interrupts: + maxItems: 1 + + label: + description: Descriptive name of the key. + + linux,code: + description: Key / Axis code to emit. + + linux,input-type: + default: 1 # EV_KEY + + linux,input-value: + description: | + If linux,input-type is EV_ABS or EV_REL then this + value is sent for events this button generates when pressed. + EV_ABS/EV_REL axis will generate an event with a value of 0 + when all buttons with linux,input-type == type and + linux,code == axis are released. This value is interpreted + as a signed 32 bit value, e.g. to make a button generate a + value of -1 use: + + linux,input-value = <0xffffffff>; /* -1 */ + + $ref: /schemas/types.yaml#/definitions/uint32 + + debounce-interval: + description: + Debouncing interval time in milliseconds. If not specified defaults to 5. + $ref: /schemas/types.yaml#/definitions/uint32 + + default: 5 + + wakeup-source: + description: Button can wake-up the system. + + wakeup-event-action: + description: | + Specifies whether the key should wake the system when asserted, when + deasserted, or both. This property is only valid for keys that wake up the + system (e.g., when the "wakeup-source" property is also provided). + + Supported values are defined in linux-event-codes.h: + + EV_ACT_ANY - both asserted and deasserted + EV_ACT_ASSERTED - asserted + EV_ACT_DEASSERTED - deasserted + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + linux,can-disable: + description: + Indicates that button is connected to dedicated (not shared) interrupt + which can be disabled to suppress events from the button. + type: boolean + + required: + - linux,code + + anyOf: + - required: + - interrupts + - required: + - interrupts-extended + - required: + - gpios + + dependencies: + wakeup-event-action: [ wakeup-source ] + linux,input-value: [ gpios ] + + unevaluatedProperties: false + +allOf: + - $ref: input.yaml# + - if: + properties: + compatible: + const: gpio-keys-polled + then: + required: + - poll-interval + else: + properties: + poll-interval: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + + key-up { + label = "GPIO Key UP"; + linux,code = <103>; + gpios = <&gpio1 0 1>; + }; + + key-down { + label = "GPIO Key DOWN"; + linux,code = <108>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt new file mode 100644 index 000000000..570dc10f0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -0,0 +1,49 @@ +* GPIO driven matrix keypad device tree bindings + +GPIO driven matrix keypad is used to interface a SoC with a matrix keypad. +The matrix keypad supports multiple row and column lines, a key can be +placed at each intersection of a unique row and a unique column. The matrix +keypad can sense a key-press and key-release by means of GPIO lines and +report the event using GPIO interrupts to the cpu. + +Required Properties: +- compatible: Should be "gpio-matrix-keypad" +- row-gpios: List of gpios used as row lines. The gpio specifier + for this property depends on the gpio controller to + which these row lines are connected. +- col-gpios: List of gpios used as column lines. The gpio specifier + for this property depends on the gpio controller to + which these column lines are connected. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt + +Optional Properties: +- linux,no-autorepeat: do no enable autorepeat feature. +- wakeup-source: use any event on keypad as wakeup event. + (Legacy property supported: "linux,wakeup") +- debounce-delay-ms: debounce interval in milliseconds +- col-scan-delay-us: delay, measured in microseconds, that is needed + before we can scan keypad after activating column gpio +- drive-inactive-cols: drive inactive columns during scan, + default is to turn inactive columns into inputs. + +Example: + matrix-keypad { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio2 25 0 + &gpio2 26 0 + &gpio2 27 0>; + + col-gpios = <&gpio2 21 0 + &gpio2 22 0>; + + linux,keymap = <0x0000008B + 0x0100009E + 0x02000069 + 0x0001006A + 0x0101001C + 0x0201006C>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-mouse.txt b/Documentation/devicetree/bindings/input/gpio-mouse.txt new file mode 100644 index 000000000..519510a11 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-mouse.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for GPIO attached mice + +This simply uses standard GPIO handles to define a simple mouse connected +to 5-7 GPIO lines. + +Required properties: + - compatible: must be "gpio-mouse" + - scan-interval-ms: The scanning interval in milliseconds + - up-gpios: GPIO line phandle to the line indicating "up" + - down-gpios: GPIO line phandle to the line indicating "down" + - left-gpios: GPIO line phandle to the line indicating "left" + - right-gpios: GPIO line phandle to the line indicating "right" + +Optional properties: + - button-left-gpios: GPIO line handle to the left mouse button + - button-middle-gpios: GPIO line handle to the middle mouse button + - button-right-gpios: GPIO line handle to the right mouse button +Example: + +#include <dt-bindings/gpio/gpio.h> + +gpio-mouse { + compatible = "gpio-mouse"; + scan-interval-ms = <50>; + up-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + down-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + left-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + right-gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + button-left-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + button-middle-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + button-right-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/input/gpio-vibrator.yaml b/Documentation/devicetree/bindings/input/gpio-vibrator.yaml new file mode 100644 index 000000000..2384465ea --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-vibrator.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/gpio-vibrator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO vibrator + +maintainers: + - Luca Weiss <luca@z3ntu.xyz> + +description: |+ + Registers a GPIO device as vibrator, where the on/off capability is controlled by a GPIO. + +properties: + compatible: + const: gpio-vibrator + + enable-gpios: + maxItems: 1 + + vcc-supply: + description: Regulator that provides power + +required: + - compatible + - enable-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + vibrator { + compatible = "gpio-vibrator"; + enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>; + vcc-supply = <&pm8941_l18>; + }; diff --git a/Documentation/devicetree/bindings/input/hid-over-i2c.yaml b/Documentation/devicetree/bindings/input/hid-over-i2c.yaml new file mode 100644 index 000000000..7156b08f7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/hid-over-i2c.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/hid-over-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HID over I2C Devices + +maintainers: + - Benjamin Tissoires <benjamin.tissoires@redhat.com> + - Jiri Kosina <jkosina@suse.cz> + +description: |+ + HID over I2C provides support for various Human Interface Devices over the + I2C bus. These devices can be for example touchpads, keyboards, touch screens + or sensors. + + The specification has been written by Microsoft and is currently available here: + https://msdn.microsoft.com/en-us/library/windows/hardware/hh852380.aspx + + If this binding is used, the kernel module i2c-hid will handle the communication + with the device and the generic hid core layer will handle the protocol. + +allOf: + - $ref: /schemas/input/touchscreen/touchscreen.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - wacom,w9013 + - const: hid-over-i2c + - description: Just "hid-over-i2c" alone is allowed, but not recommended. + const: hid-over-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + hid-descr-addr: + description: HID descriptor address + $ref: /schemas/types.yaml#/definitions/uint32 + + post-power-on-delay-ms: + description: Time required by the device after enabling its regulators + or powering it on, before it is ready for communication. + + touchscreen-inverted-x: true + + touchscreen-inverted-y: true + + vdd-supply: + description: 3.3V supply + + vddl-supply: + description: 1.8V supply + + wakeup-source: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hid@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + hid-descr-addr = <0x0020>; + interrupts = <3 2>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/input/ibm,op-panel.yaml b/Documentation/devicetree/bindings/input/ibm,op-panel.yaml new file mode 100644 index 000000000..29a1879e3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ibm,op-panel.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/ibm,op-panel.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IBM Operation Panel + +maintainers: + - Eddie James <eajames@linux.ibm.com> + +allOf: + - $ref: input.yaml# + +description: | + The IBM Operation Panel provides a simple interface to control the connected + server. It has a display and three buttons: two directional arrows and one + 'Enter' button. + +properties: + compatible: + const: ibm,op-panel + + reg: + maxItems: 1 + + linux,keycodes: + minItems: 1 + maxItems: 3 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/i2c/i2c.h> + #include <dt-bindings/input/input.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ibm-op-panel@62 { + compatible = "ibm,op-panel"; + reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>; + linux,keycodes = <KEY_UP>, <KEY_DOWN>, <KEY_ENTER>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/imx-keypad.yaml b/Documentation/devicetree/bindings/input/imx-keypad.yaml new file mode 100644 index 000000000..7514df62b --- /dev/null +++ b/Documentation/devicetree/bindings/input/imx-keypad.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/imx-keypad.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX Keypad Port(KPP) + +maintainers: + - Liu Ying <gnuiyl@gmail.com> + +allOf: + - $ref: "/schemas/input/matrix-keymap.yaml#" + +description: | + The KPP is designed to interface with a keypad matrix with 2-point contact + or 3-point contact keys. The KPP is designed to simplify the software task + of scanning a keypad matrix. The KPP is capable of detecting, debouncing, + and decoding one or multiple keys pressed simultaneously on a keypad. + +properties: + compatible: + oneOf: + - const: fsl,imx21-kpp + - items: + - enum: + - fsl,imx25-kpp + - fsl,imx27-kpp + - fsl,imx31-kpp + - fsl,imx35-kpp + - fsl,imx51-kpp + - fsl,imx53-kpp + - fsl,imx50-kpp + - fsl,imx6q-kpp + - fsl,imx6sx-kpp + - fsl,imx6sl-kpp + - fsl,imx6sll-kpp + - fsl,imx6ul-kpp + - fsl,imx7d-kpp + - const: fsl,imx21-kpp + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - linux,keymap + +unevaluatedProperties: false + +examples: + - | + keypad@73f94000 { + compatible = "fsl,imx51-kpp", "fsl,imx21-kpp"; + reg = <0x73f94000 0x4000>; + interrupts = <60>; + clocks = <&clks 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_1>; + linux,keymap = <0x00000067 /* KEY_UP */ + 0x0001006c /* KEY_DOWN */ + 0x00020072 /* KEY_VOLUMEDOWN */ + 0x00030066 /* KEY_HOME */ + 0x0100006a /* KEY_RIGHT */ + 0x01010069 /* KEY_LEFT */ + 0x0102001c /* KEY_ENTER */ + 0x01030073 /* KEY_VOLUMEUP */ + 0x02000040 /* KEY_F6 */ + 0x02010042 /* KEY_F8 */ + 0x02020043 /* KEY_F9 */ + 0x02030044 /* KEY_F10 */ + 0x0300003b /* KEY_F1 */ + 0x0301003c /* KEY_F2 */ + 0x0302003d /* KEY_F3 */ + 0x03030074>; /* KEY_POWER */ + }; diff --git a/Documentation/devicetree/bindings/input/input-reset.txt b/Documentation/devicetree/bindings/input/input-reset.txt new file mode 100644 index 000000000..1ca6cc5eb --- /dev/null +++ b/Documentation/devicetree/bindings/input/input-reset.txt @@ -0,0 +1,33 @@ +Input: sysrq reset sequence + +A simple binding to represent a set of keys as described in +include/uapi/linux/input.h. This is to communicate a sequence of keys to the +sysrq driver. Upon holding the keys for a specified amount of time (if +specified) the system is sync'ed and reset. + +Key sequences are global to the system but all the keys in a set must be coming +from the same input device. + +The /chosen node should contain a 'linux,sysrq-reset-seq' child node to define +a set of keys. + +Required property: +keyset: array of Linux keycodes, one keycode per cell. + +Optional property: +timeout-ms: duration keys must be pressed together in milliseconds before +generating a sysrq. If omitted the system is rebooted immediately when a valid +sequence has been recognized. + +Example: + + chosen { + linux,sysrq-reset-seq { + keyset = <0x03 + 0x04 + 0x0a>; + timeout-ms = <3000>; + }; + }; + +Would represent KEY_2, KEY_3 and KEY_9. diff --git a/Documentation/devicetree/bindings/input/input.yaml b/Documentation/devicetree/bindings/input/input.yaml new file mode 100644 index 000000000..17512f434 --- /dev/null +++ b/Documentation/devicetree/bindings/input/input.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/input.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common input schema binding + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +properties: + autorepeat: + description: Enable autorepeat when key is pressed and held down. + type: boolean + + linux,keycodes: + description: + Specifies an array of numeric keycode values to be used for reporting + button presses. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + minimum: 0 + maximum: 0x2ff + + linux,code: + description: + Specifies a single numeric keycode value to be used for reporting + button/switch events. Specify KEY_RESERVED (0) to opt out of event + reporting. + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 0x2ff + + linux,input-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 1 # EV_KEY + - 2 # EV_REL + - 3 # EV_ABS + - 5 # EV_SW + description: + Specifies whether the event is to be interpreted as a key, relative, + absolute, or switch. + + poll-interval: + description: Poll interval time in milliseconds. + $ref: /schemas/types.yaml#/definitions/uint32 + + power-off-time-sec: + description: + Duration in seconds which the key should be kept pressed for device to + power off automatically. Device with key pressed shutdown feature can + specify this property. + + reset-time-sec: + description: + Duration in seconds which the key should be kept pressed for device to + reset automatically. Device with key pressed reset feature can specify + this property. + +dependencies: + linux,input-type: [ "linux,code" ] + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/input/iqs269a.yaml b/Documentation/devicetree/bindings/input/iqs269a.yaml new file mode 100644 index 000000000..3c430d385 --- /dev/null +++ b/Documentation/devicetree/bindings/input/iqs269a.yaml @@ -0,0 +1,552 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/iqs269a.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS269A Capacitive Touch Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS269A is an 8-channel capacitive touch controller that features + additional Hall-effect and inductive sensing capabilities. + + Link to datasheet: https://www.azoteq.com/ + +properties: + compatible: + const: azoteq,iqs269a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + azoteq,hall-enable: + type: boolean + description: + Enables Hall-effect sensing on channels 6 and 7. In this case, keycodes + assigned to channel 6 are ignored and keycodes assigned to channel 7 are + interpreted as switch codes. Refer to the datasheet for requirements im- + posed on channels 6 and 7 by Hall-effect sensing. + + azoteq,suspend-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the power mode during suspend as follows: + 0: Automatic (same as normal runtime, i.e. suspend/resume disabled) + 1: Low power (all sensing at a reduced reporting rate) + 2: Ultra-low power (channel 0 proximity sensing) + 3: Halt (no sensing) + + azoteq,clk-div: + type: boolean + description: Divides the device's core clock by a factor of 4. + + azoteq,ulp-update: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + default: 3 + description: Specifies the ultra-low-power mode update rate. + + azoteq,reseed-offset: + type: boolean + description: + Applies an 8-count offset to all long-term averages upon either ATI or + reseed events. + + azoteq,filt-str-lp-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during low-power mode. + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode. + + azoteq,filt-str-np-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during normal-power mode. + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode. + + azoteq,rate-np-ms: + minimum: 0 + maximum: 255 + default: 16 + description: Specifies the report rate (in ms) during normal-power mode. + + azoteq,rate-lp-ms: + minimum: 0 + maximum: 255 + default: 160 + description: Specifies the report rate (in ms) during low-power mode. + + azoteq,rate-ulp-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 160 + description: Specifies the report rate (in ms) during ultra-low-power mode. + + azoteq,timeout-pwr-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 2560 + description: + Specifies the length of time (in ms) to wait for an event during normal- + power mode before transitioning to low-power mode. + + azoteq,timeout-lta-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 32768 + description: + Specifies the length of time (in ms) to wait before resetting the long- + term average of all channels. Specify the maximum timeout to disable it + altogether. + + azoteq,ati-band-disable: + type: boolean + description: Disables the ATI band check. + + azoteq,ati-lp-only: + type: boolean + description: Limits automatic ATI to low-power mode. + + azoteq,ati-band-tighten: + type: boolean + description: Tightens the ATI band from 1/8 to 1/16 of the desired target. + + azoteq,filt-disable: + type: boolean + description: Disables all raw count filtering. + + azoteq,gpio3-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + default: 0 + description: + Selects the channel for which the GPIO3 pin represents touch state. + + azoteq,dual-direction: + type: boolean + description: + Specifies that long-term averages are to freeze in the presence of either + increasing or decreasing counts, thereby permitting events to be reported + in either direction. + + azoteq,tx-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the inductive sensing excitation frequency as follows (paren- + thesized numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 16 MHz (4 MHz) + 1: 8 MHz (2 MHz) + 2: 4 MHz (1 MHz) + 3: 2 MHz (500 kHz) + + azoteq,global-cap-increase: + type: boolean + description: Increases the global capacitance adder from 0.5 pF to 1.5 pF. + + azoteq,reseed-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the event(s) that prompt the device to reseed (i.e. reset the + long-term average) of an associated channel as follows: + 0: None + 1: Proximity + 2: Proximity or touch + 3: Proximity, touch or deep touch + + azoteq,tracking-enable: + type: boolean + description: + Enables all associated channels to track their respective reference + channels. + + azoteq,filt-str-slider: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 1 + description: Specifies the slider coordinate filter strength. + +patternProperties: + "^channel@[0-7]$": + type: object + description: + Represents a single sensing channel. A channel is active if defined and + inactive otherwise. + + properties: + reg: + minimum: 0 + maximum: 7 + description: Index of the channel. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the channel from being reseeded if the long-term average + timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,blocking-enable: + type: boolean + description: Specifies that the channel is a blocking channel. + + azoteq,slider0-select: + type: boolean + description: Specifies that the channel participates in slider 0. + + azoteq,slider1-select: + type: boolean + description: Specifies that the channel participates in slider 1. + + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRX pin(s) associated with the channel. By default, only + the CRX pin corresponding to the channel's index is enabled (e.g. CRX0 + for channel 0). + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + default: [0, 1, 2, 3, 4, 5, 6, 7] + description: Specifies the TX pin(s) associated with the channel. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-float-inactive: + type: boolean + description: Floats any inactive CRX pins instead of grounding them. + + azoteq,local-cap-size: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + description: | + Specifies the capacitance to be added to the channel as follows: + 0: None + 1: Global adder (based on 'azoteq,global-cap-increase') + 2: Global adder + 0.5 pF + + azoteq,invert-enable: + type: boolean + description: + Inverts the polarity of the states reported for proximity, touch and + deep-touch events relative to their respective thresholds. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 2 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 9, 14, 15] + default: 0 + description: | + Specifies the channel's sensing mode as follows: + 0: Self capacitance + 1: Projected capacitance + 9: Self or mutual inductance + 14: Hall effect + 15: Temperature + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 1 + description: | + Specifies the channel's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + azoteq,static-enable: + type: boolean + description: Enables the static front-end for the channel. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 3 + description: | + Specifies the channel's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [75, 100, 150, 200] + default: 100 + description: Specifies the channel's ATI base. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + default: 512 + description: Specifies the channel's ATI target. + + azoteq,assoc-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the associated channels for which the channel serves as a + reference channel. By default, no channels are selected. + + azoteq,assoc-weight: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the channel's impact weight if it acts as an associated + channel (0 = 0% impact, 255 = 200% impact). + + patternProperties: + "^event-prox(-alt)?$": + type: object + $ref: input.yaml# + description: + Represents a proximity event reported by the channel in response to + a decrease in counts. Node names suffixed with '-alt' instead corre- + spond to an increase in counts. + + By default, the long-term average tracks an increase in counts such + that only events corresponding to a decrease in counts are reported + (refer to the datasheet for more information). + + Specify 'azoteq,dual-direction' to freeze the long-term average when + the counts increase or decrease such that events of either direction + can be reported. Alternatively, specify 'azoteq,invert-enable' to in- + vert the polarity of the states reported by the channel. + + Complementary events (e.g. event-touch and event-touch-alt) can both + be present and specify different key or switch codes, but not differ- + ent thresholds or hysteresis (if applicable). + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 10 + description: Specifies the threshold for the event. + + linux,code: true + + additionalProperties: false + + "^event-touch(-alt)?$": + type: object + $ref: input.yaml# + description: Represents a touch event reported by the channel. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 8 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 4 + description: Specifies the hysteresis for the event. + + linux,code: true + + additionalProperties: false + + "^event-deep(-alt)?$": + type: object + $ref: input.yaml# + description: Represents a deep-touch event reported by the channel. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 26 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + description: Specifies the hysteresis for the event. + + linux,code: true + + additionalProperties: false + + required: + - reg + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@44 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "azoteq,iqs269a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + azoteq,hall-enable; + azoteq,suspend-mode = <2>; + + channel@0 { + reg = <0x0>; + + event-prox { + linux,code = <KEY_POWER>; + }; + }; + + channel@1 { + reg = <0x1>; + azoteq,slider0-select; + }; + + channel@2 { + reg = <0x2>; + azoteq,slider0-select; + }; + + channel@3 { + reg = <0x3>; + azoteq,slider0-select; + }; + + channel@4 { + reg = <0x4>; + azoteq,slider0-select; + }; + + channel@5 { + reg = <0x5>; + azoteq,slider0-select; + }; + + channel@6 { + reg = <0x6>; + azoteq,invert-enable; + azoteq,static-enable; + azoteq,reseed-disable; + azoteq,rx-enable = <0>; + azoteq,sense-freq = <0x0>; + azoteq,sense-mode = <0xE>; + azoteq,ati-mode = <0x0>; + azoteq,ati-base = <200>; + azoteq,ati-target = <320>; + }; + + channel@7 { + reg = <0x7>; + azoteq,invert-enable; + azoteq,static-enable; + azoteq,reseed-disable; + azoteq,rx-enable = <0>, <6>; + azoteq,sense-freq = <0x0>; + azoteq,sense-mode = <0xE>; + azoteq,ati-mode = <0x3>; + azoteq,ati-base = <200>; + azoteq,ati-target = <320>; + + event-touch { + linux,code = <SW_LID>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/iqs626a.yaml b/Documentation/devicetree/bindings/input/iqs626a.yaml new file mode 100644 index 000000000..7a2750209 --- /dev/null +++ b/Documentation/devicetree/bindings/input/iqs626a.yaml @@ -0,0 +1,838 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/iqs626a.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS626A Capacitive Touch Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS626A is a 14-channel capacitive touch controller that features + additional Hall-effect and inductive sensing capabilities. + + Link to datasheet: https://www.azoteq.com/ + +allOf: + - $ref: touchscreen/touchscreen.yaml# + +properties: + compatible: + const: azoteq,iqs626a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + azoteq,suspend-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the power mode during suspend as follows: + 0: Automatic (same as normal runtime, i.e. suspend/resume disabled) + 1: Low power (all sensing at a reduced reporting rate) + 2: Ultra-low power (ULP channel proximity sensing) + 3: Halt (no sensing) + + azoteq,clk-div: + type: boolean + description: Divides the device's core clock by a factor of 4. + + azoteq,ulp-enable: + type: boolean + description: + Permits the device to automatically enter ultra-low-power mode from low- + power mode. + + azoteq,ulp-update: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 3 + description: | + Specifies the rate at which the trackpad, generic and Hall channels are + updated during ultra-low-power mode as follows: + 0: 8 + 1: 13 + 2: 28 + 3: 54 + 4: 89 + 5: 135 + 6: 190 + 7: 256 + + azoteq,ati-band-disable: + type: boolean + description: Disables the ATI band check. + + azoteq,ati-lp-only: + type: boolean + description: Limits automatic ATI to low-power mode. + + azoteq,gpio3-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 1 + description: | + Selects the channel or group of channels for which the GPIO3 pin + represents touch state as follows: + 0: None + 1: ULP channel + 2: Trackpad + 3: Trackpad + 4: Generic channel 0 + 5: Generic channel 1 + 6: Generic channel 2 + 7: Hall channel + + azoteq,reseed-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the event(s) that prompt the device to reseed (i.e. reset the + long-term average) of an associated channel as follows: + 0: None + 1: Proximity + 2: Proximity or touch + 3: Proximity, touch or deep touch + + azoteq,thresh-extend: + type: boolean + description: Multiplies all touch and deep-touch thresholds by 4. + + azoteq,tracking-enable: + type: boolean + description: + Enables all associated channels to track their respective reference + channels. + + azoteq,reseed-offset: + type: boolean + description: + Applies an 8-count offset to all long-term averages upon either ATI or + reseed events. + + azoteq,rate-np-ms: + minimum: 0 + maximum: 255 + default: 150 + description: Specifies the report rate (in ms) during normal-power mode. + + azoteq,rate-lp-ms: + minimum: 0 + maximum: 255 + default: 150 + description: Specifies the report rate (in ms) during low-power mode. + + azoteq,rate-ulp-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: Specifies the report rate (in ms) during ultra-low-power mode. + + azoteq,timeout-pwr-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 2560 + description: + Specifies the length of time (in ms) to wait for an event before moving + from normal-power mode to low-power mode, or (if 'azoteq,ulp-enable' is + present) from low-power mode to ultra-low-power mode. + + azoteq,timeout-lta-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 40960 + description: + Specifies the length of time (in ms) to wait before resetting the long- + term average of all channels. Specify the maximum timeout to disable it + altogether. + + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +patternProperties: + "^ulp-0|generic-[0-2]|hall$": + type: object + description: + Represents a single sensing channel. A channel is active if defined and + inactive otherwise. + + properties: + azoteq,ati-exclude: + type: boolean + description: + Prevents the channel from participating in an ATI event that is + manually triggered during initialization. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the channel from being reseeded if the long-term average + timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-inactive: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + description: | + Specifies how inactive CRX pins are to be terminated as follows: + 0: VSS + 1: Floating + 2: VREG (generic channels only) + + azoteq,linearize: + type: boolean + description: + Enables linearization of the channel's counts (generic and Hall + channels) or inverts the polarity of the channel's proximity or + touch states (ULP channel). + + azoteq,dual-direction: + type: boolean + description: + Specifies that the channel's long-term average is to freeze in the + presence of either increasing or decreasing counts, thereby permit- + ting events to be reported in either direction. + + azoteq,filt-disable: + type: boolean + description: Disables raw count filtering for the channel. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the channel's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + The default value is a function of the channel and the device's reset + user interface (RUI); reference the datasheet for further information + about the available RUI options. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [75, 100, 150, 200] + description: + Specifies the channel's ATI base. The default value is a function + of the channel and the device's RUI. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + description: + Specifies the channel's ATI target. The default value is a function + of the channel and the device's RUI. + + azoteq,cct-increase: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 16 + default: 0 + description: + Specifies the degree to which the channel's charge cycle time is to + be increased, with 0 representing no increase. The maximum value is + limited to 4 in the case of the ULP channel, and the property is un- + available entirely in the case of the Hall channel. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + This property is unavailable in the case of the Hall channel. + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the channel's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,ati-band-tighten: + type: boolean + description: + Tightens the ATI band from 1/8 to 1/16 of the desired target (ULP and + generic channels only). + + azoteq,proj-enable: + type: boolean + description: Enables projected-capacitance sensing (ULP channel only). + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode (ULP + and generic channels only). + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode (ULP and + generic channels only). + + azoteq,filt-str-np-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during normal-power + mode (ULP and generic channels only). + + azoteq,filt-str-lp-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during low-power mode + (ULP and generic channels only). + + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRX pin(s) associated with the channel. + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the TX pin(s) associated with the channel. + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,local-cap-size: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4] + default: 0 + description: | + Specifies the capacitance to be added to the channel as follows: + 0: 0 pF + 1: 0.5 pF + 2: 1.0 pF + 3: 1.5 pF + 4: 2.0 pF + + This property is unavailable in the case of the ULP or Hall channels. + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 8, 9, 12, 14, 15] + description: | + Specifies the channel's sensing mode as follows: + 0: Self capacitance + 1: Projected capacitance + 8: Self inductance + 9: Mutual inductance + 12: External + 14: Hall effect + 15: Temperature + + This property is unavailable in the case of the ULP or Hall channels. + The default value is a function of the channel and the device's RUI. + + azoteq,tx-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the inductive sensing excitation frequency as follows + (parenthesized numbers represent the frequency if 'azoteq,clk-div' + is present): + 0: 16 MHz (4 MHz) + 1: 8 MHz (2 MHz) + 2: 4 MHz (1 MHz) + 3: 2 MHz (500 kHz) + + This property is unavailable in the case of the ULP or Hall channels. + + azoteq,invert-enable: + type: boolean + description: + Inverts the polarity of the states reported for proximity, touch and + deep-touch events relative to their respective thresholds (generic + channels only). + + azoteq,comp-disable: + type: boolean + description: + Disables compensation for the channel (generic channels only). + + azoteq,static-enable: + type: boolean + description: + Enables the static front-end for the channel (generic channels only). + + azoteq,assoc-select: + $ref: /schemas/types.yaml#/definitions/string-array + minItems: 1 + maxItems: 6 + items: + enum: + - ulp-0 + - trackpad-3x2 + - trackpad-3x3 + - generic-0 + - generic-1 + - generic-2 + - hall + description: + Specifies the associated channels for which the channel serves as a + reference channel. By default, no channels are selected. This prop- + erty is only available for the generic channels. + + azoteq,assoc-weight: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the channel's impact weight if it acts as an associated + channel (0 = 0% impact, 255 = 200% impact). This property is only + available for the generic channels. + + patternProperties: + "^event-(prox|touch|deep)(-alt)?$": + type: object + $ref: input.yaml# + description: + Represents a proximity, touch or deep-touch event reported by the + channel in response to a decrease in counts. Node names suffixed with + '-alt' instead correspond to an increase in counts. + + By default, the long-term average tracks an increase in counts such + that only events corresponding to a decrease in counts are reported + (refer to the datasheet for more information). + + Specify 'azoteq,dual-direction' to freeze the long-term average when + the counts increase or decrease such that events of either direction + can be reported. Alternatively, specify 'azoteq,invert-enable' to in- + vert the polarity of the states reported by the channel. + + Complementary events (e.g. event-touch and event-touch-alt) can both + be present and specify different key or switch codes, but not differ- + ent thresholds or hysteresis (if applicable). + + Proximity events are unavailable in the case of the Hall channel, and + deep-touch events are only available for the generic channels. Unless + otherwise specified, default values are a function of the channel and + the device's RUI. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the hysteresis for the event (touch and deep-touch + events only). + + linux,code: true + + linux,input-type: + enum: [1, 5] + description: + Specifies whether the event is to be interpreted as a key (1) or + a switch (5). By default, Hall-channel events are interpreted as + switches and all others are interpreted as keys. + + additionalProperties: false + + dependencies: + azoteq,assoc-weight: ["azoteq,assoc-select"] + + additionalProperties: false + + "^trackpad-3x[2-3]$": + type: object + $ref: input.yaml# + description: + Represents all channels associated with the trackpad. The channels are + collectively active if the trackpad is defined and inactive otherwise. + + properties: + azoteq,ati-exclude: + type: boolean + description: + Prevents the trackpad channels from participating in an ATI event + that is manually triggered during initialization. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the trackpad channels from being reseeded if the long-term + average timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-inactive: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + default: 0 + description: | + Specifies how inactive CRX pins are to be terminated as follows: + 0: VSS + 1: Floating + + azoteq,linearize: + type: boolean + description: Inverts the polarity of the trackpad's touch state. + + azoteq,dual-direction: + type: boolean + description: + Specifies that the trackpad's long-term averages are to freeze in + the presence of either increasing or decreasing counts, thereby + permitting events to be reported in either direction. + + azoteq,filt-disable: + type: boolean + description: Disables raw count filtering for the trackpad channels. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the trackpad's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 6 + maxItems: 9 + items: + minimum: 45 + maximum: 300 + default: [45, 45, 45, 45, 45, 45, 45, 45, 45] + description: Specifies each individual trackpad channel's ATI base. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + default: 0 + description: Specifies the trackpad's ATI target. + + azoteq,cct-increase: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 4 + default: 0 + description: + Specifies the degree to which the trackpad's charge cycle time is to + be increased, with 0 representing no increase. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the trackpad's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + azoteq,ati-band-tighten: + type: boolean + description: + Tightens the ATI band from 1/8 to 1/16 of the desired target. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 6 + maxItems: 9 + items: + minimum: 0 + maximum: 255 + default: [0, 0, 0, 0, 0, 0, 0, 0, 0] + description: + Specifies each individual trackpad channel's touch threshold. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + description: Specifies the trackpad's touch hysteresis. + + azoteq,lta-update: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 0 + description: | + Specifies the update rate of the trackpad's long-term average during + ultra-low-power mode as follows: + 0: 2 + 1: 4 + 2: 8 + 3: 16 + 4: 32 + 5: 64 + 6: 128 + 7: 255 + + azoteq,filt-str-trackpad: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: Specifies the trackpad coordinate filter strength. + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode. + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode. + + linux,keycodes: + minItems: 1 + maxItems: 6 + description: | + Specifies the numeric keycodes associated with each available gesture + in the following order (enter 0 for unused gestures): + 0: Positive flick or swipe in X direction + 1: Negative flick or swipe in X direction + 2: Positive flick or swipe in Y direction + 3: Negative flick or swipe in Y direction + 4: Tap + 5: Hold + + azoteq,gesture-swipe: + type: boolean + description: + Directs the device to interpret axial gestures as a swipe (finger + remains on trackpad) instead of a flick (finger leaves trackpad). + + azoteq,timeout-tap-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: + Specifies the length of time (in ms) within which a trackpad touch + must be released in order to be interpreted as a tap. + + azoteq,timeout-swipe-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: + Specifies the length of time (in ms) within which an axial gesture + must be completed in order to be interpreted as a flick or swipe. + + azoteq,thresh-swipe: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the number of points across which an axial gesture must + travel in order to be interpreted as a flick or swipe. + + dependencies: + azoteq,gesture-swipe: ["linux,keycodes"] + azoteq,timeout-tap-ms: ["linux,keycodes"] + azoteq,timeout-swipe-ms: ["linux,keycodes"] + azoteq,thresh-swipe: ["linux,keycodes"] + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@44 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "azoteq,iqs626a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + azoteq,rate-np-ms = <16>; + azoteq,rate-lp-ms = <160>; + + azoteq,timeout-pwr-ms = <2560>; + azoteq,timeout-lta-ms = <32768>; + + ulp-0 { + azoteq,meas-cap-decrease; + + azoteq,ati-base = <75>; + azoteq,ati-target = <1024>; + + azoteq,rx-enable = <2>, <3>, <4>, + <5>, <6>, <7>; + + event-prox { + linux,code = <KEY_POWER>; + }; + }; + + trackpad-3x3 { + azoteq,filt-str-np-cnt = <1>; + azoteq,filt-str-lp-cnt = <1>; + + azoteq,hyst = <4>; + azoteq,thresh = <35>, <40>, <40>, + <38>, <33>, <38>, + <35>, <35>, <35>; + + azoteq,ati-mode = <3>; + azoteq,ati-base = <195>, <195>, <195>, + <195>, <195>, <195>, + <195>, <195>, <195>; + azoteq,ati-target = <512>; + + azoteq,proj-bias = <1>; + azoteq,sense-freq = <2>; + + linux,keycodes = <KEY_VOLUMEUP>, + <KEY_VOLUMEDOWN>, + <KEY_NEXTSONG>, + <KEY_PREVIOUSSONG>, + <KEY_PLAYPAUSE>, + <KEY_STOPCD>; + + azoteq,gesture-swipe; + azoteq,timeout-swipe-ms = <800>; + azoteq,timeout-tap-ms = <400>; + azoteq,thresh-swipe = <40>; + }; + + /* + * Preserve the default register settings for + * the temperature-tracking channel leveraged + * by reset user interface (RUI) 1. + * + * Scalar properties (e.g. ATI mode) are left + * untouched by simply omitting them; boolean + * properties must be specified explicitly as + * needed. + */ + generic-2 { + azoteq,reseed-disable; + azoteq,meas-cap-decrease; + azoteq,dual-direction; + azoteq,comp-disable; + azoteq,static-enable; + }; + + hall { + azoteq,reseed-disable; + azoteq,meas-cap-decrease; + + event-touch { + linux,code = <SW_LID>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/iqs62x-keys.yaml b/Documentation/devicetree/bindings/input/iqs62x-keys.yaml new file mode 100644 index 000000000..0aa951f0a --- /dev/null +++ b/Documentation/devicetree/bindings/input/iqs62x-keys.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/iqs62x-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS620A/621/622/624/625 Keys and Switches + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +allOf: + - $ref: input.yaml# + +description: | + The Azoteq IQS620A, IQS621, IQS622, IQS624 and IQS625 multi-function sensors + feature a variety of self-capacitive, mutual-inductive and Hall-effect sens- + ing capabilities that can facilitate a variety of contactless key and switch + applications. + + These functions are collectively represented by a "keys" child node from the + parent MFD driver. See Documentation/devicetree/bindings/mfd/iqs62x.yaml for + further details and examples. Sensor hardware configuration (self-capacitive + vs. mutual-inductive, etc.) is selected based on the device's firmware. + +properties: + compatible: + enum: + - azoteq,iqs620a-keys + - azoteq,iqs621-keys + - azoteq,iqs622-keys + - azoteq,iqs624-keys + - azoteq,iqs625-keys + + linux,keycodes: + minItems: 1 + maxItems: 16 + description: | + Specifies the numeric keycodes associated with each available touch or + proximity event according to the following table. An 'x' indicates the + event is supported for a given device. Specify 0 for unused events. + + ------------------------------------------------------------------------- + | # | Event | IQS620A | IQS621 | IQS622 | IQS624 | IQS625 | + ------------------------------------------------------------------------- + | 0 | CH0 Touch | x | x | x | x | x | + | | Antenna 1 Touch* | x | | | | | + ------------------------------------------------------------------------- + | 1 | CH0 Proximity | x | x | x | x | x | + | | Antenna 1 Prox.* | x | | | | | + ------------------------------------------------------------------------- + | 2 | CH1 Touch | x | x | x | x | x | + | | Ant. 1 Deep Touch* | x | | | | | + ------------------------------------------------------------------------- + | 3 | CH1 Proximity | x | x | x | x | x | + ------------------------------------------------------------------------- + | 4 | CH2 Touch | x | | | | | + ------------------------------------------------------------------------- + | 5 | CH2 Proximity | x | | | | | + | | Antenna 2 Prox.* | x | | | | | + ------------------------------------------------------------------------- + | 6 | Metal (+) Touch** | x | x | | | | + | | Ant. 2 Deep Touch* | x | | | | | + ------------------------------------------------------------------------- + | 7 | Metal (+) Prox.** | x | x | | | | + | | Antenna 2 Touch* | x | | | | | + ------------------------------------------------------------------------- + | 8 | Metal (-) Touch** | x | x | | | | + ------------------------------------------------------------------------- + | 9 | Metal (-) Prox.** | x | x | | | | + ------------------------------------------------------------------------- + | 10 | SAR Active*** | x | | x | | | + ------------------------------------------------------------------------- + | 11 | SAR Quick Rel.*** | x | | x | | | + ------------------------------------------------------------------------- + | 12 | SAR Movement*** | x | | x | | | + ------------------------------------------------------------------------- + | 13 | SAR Filter Halt*** | x | | x | | | + ------------------------------------------------------------------------- + | 14 | Wheel Up | | | | x | | + ------------------------------------------------------------------------- + | 15 | Wheel Down | | | | x | | + ------------------------------------------------------------------------- + * Two-channel SAR. Replaces CH0-2 plus metal touch and proximity events + if enabled via firmware. + ** "+" and "-" refer to the polarity of a channel's delta (LTA - counts), + where "LTA" is defined as the channel's long-term average. + *** One-channel SAR. Replaces CH0-2 touch and proximity events if enabled + via firmware. + +patternProperties: + "^hall-switch-(north|south)$": + type: object + $ref: input.yaml# + description: + Represents north/south-field Hall-effect sensor touch or proximity + events. Note that north/south-field orientation is reversed on the + IQS620AXzCSR device due to its flip-chip package. + + properties: + linux,code: true + + azoteq,use-prox: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present, specifies that Hall-effect sensor reporting should + use the device's wide-range proximity threshold instead of its + close-range touch threshold (default). + + required: + - linux,code + + additionalProperties: false + +if: + properties: + compatible: + contains: + enum: + - azoteq,iqs624-keys + - azoteq,iqs625-keys +then: + patternProperties: + "^hall-switch-(north|south)$": false + +required: + - compatible + - linux,keycodes + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt new file mode 100644 index 000000000..2b075a080 --- /dev/null +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -0,0 +1,34 @@ +NXP LPC32xx Key Scan Interface + +This binding is based on the matrix-keymap binding with the following +changes: + +Required Properties: +- compatible: Should be "nxp,lpc3220-key" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. +- clocks: phandle to clock controller plus clock-specifier pair +- nxp,debounce-delay-ms: Debounce delay in ms +- nxp,scan-delay-ms: Repeated scan period in ms +- linux,keymap: the key-code to be reported when the key is pressed + and released, see also + Documentation/devicetree/bindings/input/matrix-keymap.txt + +Note: keypad,num-rows and keypad,num-columns are required, and must be equal +since LPC32xx only supports square matrices + +Example: + + key@40050000 { + compatible = "nxp,lpc3220-key"; + reg = <0x40050000 0x1000>; + clocks = <&clk LPC32XX_CLK_KEY>; + interrupt-parent = <&sic1>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt new file mode 100644 index 000000000..79f6d01ae --- /dev/null +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -0,0 +1 @@ +This file has been moved to matrix-keymap.yaml diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.yaml b/Documentation/devicetree/bindings/input/matrix-keymap.yaml new file mode 100644 index 000000000..6699d5e32 --- /dev/null +++ b/Documentation/devicetree/bindings/input/matrix-keymap.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/matrix-keymap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common key matrices binding for matrix-connected key boards + +maintainers: + - Olof Johansson <olof@lixom.net> + +description: | + A simple common binding for matrix-connected key boards. Currently targeted at + defining the keys in the scope of linux key codes since that is a stable and + standardized interface at this time. + + Some users of this binding might choose to specify secondary keymaps for + cases where there is a modifier key such as a Fn key. Proposed names + for said properties are "linux,fn-keymap" or with another descriptive + word for the modifier other from "Fn". + +properties: + linux,keymap: + $ref: '/schemas/types.yaml#/definitions/uint32-array' + description: | + An array of packed 1-cell entries containing the equivalent of row, + column and linux key-code. The 32-bit big endian cell is packed as: + row << 24 | column << 16 | key-code + + keypad,num-rows: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of row lines connected to the keypad controller. + + keypad,num-columns: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of column lines connected to the keypad controller. + +additionalProperties: true + +examples: + - | + keypad { + /* ... */ + linux,keymap = < 0x00030012 + 0x0102003a >; + keypad,num-rows = <2>; + keypad,num-columns = <8>; + }; diff --git a/Documentation/devicetree/bindings/input/max77650-onkey.yaml b/Documentation/devicetree/bindings/input/max77650-onkey.yaml new file mode 100644 index 000000000..48edc0c8c --- /dev/null +++ b/Documentation/devicetree/bindings/input/max77650-onkey.yaml @@ -0,0 +1,38 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/max77650-onkey.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Onkey driver for MAX77650 PMIC from Maxim Integrated. + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + +description: | + This module is part of the MAX77650 MFD device. For more details + see Documentation/devicetree/bindings/mfd/max77650.yaml. + + The onkey controller is represented as a sub-node of the PMIC node on + the device tree. + +allOf: + - $ref: input.yaml# + +properties: + compatible: + const: maxim,max77650-onkey + + linux,code: + default: 116 # KEY_POWER + + maxim,onkey-slide: + $ref: /schemas/types.yaml#/definitions/flag + description: + The system's button is a slide switch, not the default push button. + +required: + - compatible +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/input/mediatek,mt6779-keypad.yaml b/Documentation/devicetree/bindings/input/mediatek,mt6779-keypad.yaml new file mode 100644 index 000000000..d768c30f4 --- /dev/null +++ b/Documentation/devicetree/bindings/input/mediatek,mt6779-keypad.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/mediatek,mt6779-keypad.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek's Keypad Controller + +maintainers: + - Mattijs Korpershoek <mkorpershoek@baylibre.com> + +allOf: + - $ref: "/schemas/input/matrix-keymap.yaml#" + +description: | + Mediatek's Keypad controller is used to interface a SoC with a matrix-type + keypad device. The keypad controller supports multiple row and column lines. + A key can be placed at each intersection of a unique row and a unique column. + The keypad controller can sense a key-press and key-release and report the + event using a interrupt to the cpu. + +properties: + compatible: + oneOf: + - const: mediatek,mt6779-keypad + - items: + - enum: + - mediatek,mt6873-keypad + - const: mediatek,mt6779-keypad + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: kpd + + wakeup-source: + description: use any event on keypad as wakeup event + type: boolean + + debounce-delay-ms: + maximum: 256 + default: 16 + + mediatek,keys-per-group: + description: each (row, column) group has multiple keys + $ref: /schemas/types.yaml#/definitions/uint32 + default: 1 + maximum: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + keyboard@10010000 { + compatible = "mediatek,mt6779-keypad"; + reg = <0 0x10010000 0 0x1000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_FALLING>; + clocks = <&clk26m>; + clock-names = "kpd"; + }; + }; diff --git a/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml new file mode 100644 index 000000000..2f72ec418 --- /dev/null +++ b/Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/mediatek,pmic-keys.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek PMIC Keys + +maintainers: + - Chen Zhong <chen.zhong@mediatek.com> + +allOf: + - $ref: input.yaml# + +description: | + There are two key functions provided by MT6397, MT6323 and other MediaTek + PMICs: pwrkey and homekey. + The key functions are defined as the subnode of the function node provided + by the PMIC that is defined as a Multi-Function Device (MFD). + + For MediaTek MT6323/MT6397 PMIC bindings see + Documentation/devicetree/bindings/mfd/mt6397.txt + +properties: + compatible: + enum: + - mediatek,mt6323-keys + - mediatek,mt6331-keys + - mediatek,mt6358-keys + - mediatek,mt6397-keys + + power-off-time-sec: true + + mediatek,long-press-mode: + description: | + Key long-press force shutdown setting + 0 - disabled + 1 - pwrkey + 2 - pwrkey+homekey + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + maximum: 2 + +patternProperties: + "^((power|home)|(key-[a-z0-9-]+|[a-z0-9-]+-key))$": + $ref: input.yaml# + + properties: + interrupts: + minItems: 1 + items: + - description: Key press interrupt + - description: Key release interrupt + + interrupt-names: true + + linux-keycodes: + maxItems: 1 + + wakeup-source: true + + required: + - linux,keycodes + + if: + properties: + interrupt-names: + contains: + const: powerkey + then: + properties: + interrupt-names: + minItems: 1 + items: + - const: powerkey + - const: powerkey_r + else: + properties: + interrupt-names: + minItems: 1 + items: + - const: homekey + - const: homekey_r + + unevaluatedProperties: false + +required: + - compatible + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pmic { + compatible = "mediatek,mt6397"; + + keys { + compatible = "mediatek,mt6397-keys"; + mediatek,long-press-mode = <1>; + power-off-time-sec = <0>; + + key-power { + linux,keycodes = <KEY_POWER>; + wakeup-source; + }; + + key-home { + linux,keycodes = <KEY_VOLUMEDOWN>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml new file mode 100644 index 000000000..96358b12f --- /dev/null +++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/input/microchip,cap11xx.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Device tree bindings for Microchip CAP11xx based capacitive touch sensors + +description: | + The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive + touch controllers and LED drivers. The device communication via I2C only. + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + compatible: + enum: + - microchip,cap1106 + - microchip,cap1126 + - microchip,cap1188 + - microchip,cap1206 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + interrupts: + maxItems: 1 + description: | + Property describing the interrupt line the + device's ALERT#/CM_IRQ# pin is connected to. + The device only has one interrupt source. + + autorepeat: + description: | + Enables the Linux input system's autorepeat feature on the input device. + + linux,keycodes: + minItems: 6 + maxItems: 6 + description: | + Specifies an array of numeric keycode values to + be used for the channels. If this property is + omitted, KEY_A, KEY_B, etc are used as defaults. + The array must have exactly six entries. + + microchip,sensor-gain: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 1 + enum: [1, 2, 4, 8] + description: | + Defines the gain of the sensor circuitry. This + effectively controls the sensitivity, as a + smaller delta capacitance is required to + generate the same delta count values. + + microchip,irq-active-high: + type: boolean + description: | + By default the interrupt pin is active low + open drain. This property allows using the active + high push-pull output. + +patternProperties: + "^led@[0-7]$": + type: object + description: CAP11xx LEDs + $ref: /schemas/leds/common.yaml# + + properties: + reg: + enum: [0, 1, 2, 3, 4, 5, 6, 7] + + label: true + + linux,default-trigger: true + + default-state: true + + required: + - reg + + additionalProperties: false + +allOf: + - $ref: input.yaml + - if: + properties: + compatible: + contains: + enum: + - microchip,cap1106 + then: + patternProperties: + "^led@[0-7]$": false + +required: + - compatible + - interrupts + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@28 { + compatible = "microchip,cap1188"; + interrupt-parent = <&gpio1>; + interrupts = <0 0>; + reg = <0x28>; + autorepeat; + microchip,sensor-gain = <2>; + + linux,keycodes = <103>, /* KEY_UP */ + <106>, /* KEY_RIGHT */ + <108>, /* KEY_DOWN */ + <105>, /* KEY_LEFT */ + <109>, /* KEY_PAGEDOWN */ + <104>; /* KEY_PAGEUP */ + + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + label = "cap11xx:green:usr0"; + reg = <0>; + }; + + led@1 { + label = "cap11xx:green:usr1"; + reg = <1>; + }; + + led@2 { + label = "cap11xx:green:alive"; + reg = <2>; + linux,default-trigger = "heartbeat"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/microchip,qt1050.txt b/Documentation/devicetree/bindings/input/microchip,qt1050.txt new file mode 100644 index 000000000..80e75f962 --- /dev/null +++ b/Documentation/devicetree/bindings/input/microchip,qt1050.txt @@ -0,0 +1,78 @@ +Microchip AT42QT1050 Five-channel Touch Sensor IC + +The AT42QT1050 (QT1050) is a QTouchADC sensor device. The device can sense from +one to five keys, dependent on mode. The QT1050 includes all signal processing +functions necessary to provide stable sensing under a wide variety of changing +conditions, and the outputs are fully debounced. + +The touchkey device node should be placed inside an I2C bus node. + +Required properties: +- compatible: Must be "microchip,qt1050" +- reg: The I2C address of the device +- interrupts: The sink for the touchpad's IRQ output, + see ../interrupt-controller/interrupts.txt + +Optional properties: +- wakeup-source: touch keys can be used as a wakeup source + +Each button (key) is represented as a sub-node: + +Each not specified key or key with linux,code set to KEY_RESERVED gets disabled +in HW. + +Subnode properties: +- linux,code: Keycode to emit. +- reg: The key number. Valid values: 0, 1, 2, 3, 4. + +Optional subnode-properties: + +If a optional property is missing or has a invalid value the default value is +taken. + +- microchip,pre-charge-time-ns: + Each touchpad need some time to precharge. The value depends on the mechanical + layout. + Valid value range: 0 - 637500; values must be a multiple of 2500; + default is 0. +- microchip,average-samples: + Number of data samples which are averaged for each read. + Valid values: 1, 4, 16, 64, 256, 1024, 4096, 16384; default is 1. +- microchip,average-scaling: + The scaling factor which is used to scale the average-samples. + Valid values: 1, 2, 4, 8, 16, 32, 64, 128; default is 1. +- microchip,threshold: + Number of counts to register a touch detection. + Valid value range: 0 - 255; default is 20. + +Example: +QT1050 with 3 non continuous keys, key2 and key4 are disabled. + +touchkeys@41 { + compatible = "microchip,qt1050"; + reg = <0x41>; + interrupt-parent = <&gpio0>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + up@0 { + reg = <0>; + linux,code = <KEY_UP>; + microchip,average-samples = <64>; + microchip,average-scaling = <16>; + microchip,pre-charge-time-ns = <10000>; + }; + + right@1 { + reg = <1>; + linux,code = <KEY_RIGHT>; + microchip,average-samples = <64>; + microchip,average-scaling = <8>; + }; + + down@3 { + reg = <3>; + linux,code = <KEY_DOWN>; + microchip,average-samples = <256>; + microchip,average-scaling = <16>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt new file mode 100644 index 000000000..1faa7292e --- /dev/null +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt @@ -0,0 +1,55 @@ +* Tegra keyboard controller +The key controller has maximum 24 pins to make matrix keypad. Any pin +can be configured as row or column. The maximum column pin can be 8 +and maximum row pins can be 16 for Tegra20/Tegra30. + +Required properties: +- compatible: "nvidia,tegra20-kbc" +- reg: Register base address of KBC. +- interrupts: Interrupt number for the KBC. +- nvidia,kbc-row-pins: The KBC pins which are configured as row. This is an + array of pin numbers which is used as rows. +- nvidia,kbc-col-pins: The KBC pins which are configured as column. This is an + array of pin numbers which is used as column. +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - kbc + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: + +- linux,fn-keymap: a second keymap, same specification as the + matrix-keyboard-controller spec but to be used when the KEY_FN modifier + key is pressed. +- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing +- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts +- nvidia,ghost-filter: enable ghost filtering for this device +- wakeup-source: configure keyboard as a wakeup source for suspend/resume + (Legacy property supported: "nvidia,wakeup-source") + +Example: + +keyboard: keyboard { + compatible = "nvidia,tegra20-kbc"; + reg = <0x7000e200 0x100>; + interrupts = <0 85 0x04>; + clocks = <&tegra_car 36>; + resets = <&tegra_car 36>; + reset-names = "kbc"; + nvidia,ghost-filter; + nvidia,debounce-delay-ms = <640>; + nvidia,kbc-row-pins = <0 1 2>; /* pin 0, 1, 2 as rows */ + nvidia,kbc-col-pins = <11 12 13>; /* pin 11, 12, 13 as columns */ + linux,keymap = <0x00000074 + 0x00010067 + 0x00020066 + 0x01010068 + 0x02000069 + 0x02010070 + 0x02020071>; +}; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt new file mode 100644 index 000000000..34ed1c60f --- /dev/null +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -0,0 +1,28 @@ +* TI's Keypad Controller device tree bindings + +TI's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,omap4-keypad": For controllers compatible with omap4 keypad + controller. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. + +Example: + keypad@4ae1c000{ + compatible = "ti,omap4-keypad"; + keypad,num-rows = <2>; + keypad,num-columns = <8>; + linux,keypad-no-autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/pine64,pinephone-keyboard.yaml b/Documentation/devicetree/bindings/input/pine64,pinephone-keyboard.yaml new file mode 100644 index 000000000..e4a0ac0ff --- /dev/null +++ b/Documentation/devicetree/bindings/input/pine64,pinephone-keyboard.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/pine64,pinephone-keyboard.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Pine64 PinePhone keyboard device tree bindings + +maintainers: + - Samuel Holland <samuel@sholland.org> + +description: + A keyboard accessory is available for the Pine64 PinePhone and PinePhone Pro. + It connects via I2C, providing a raw scan matrix, a flashing interface, and a + subordinate I2C bus for communication with a battery charger IC. + +properties: + compatible: + const: pine64,pinephone-keyboard + + reg: + const: 0x15 + + interrupts: + maxItems: 1 + + vbat-supply: + description: Supply for the keyboard MCU + + wakeup-source: true + + i2c: + $ref: /schemas/i2c/i2c-controller.yaml# + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + keyboard@15 { + compatible = "pine64,pinephone-keyboard"; + reg = <0x15>; + interrupt-parent = <&r_pio>; + interrupts = <0 12 IRQ_TYPE_EDGE_FALLING>; /* PL12 */ + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@75 { + reg = <0x75>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file mode 100644 index 000000000..3029c5694 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt @@ -0,0 +1,16 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt new file mode 100644 index 000000000..8fc0e48c2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -0,0 +1,24 @@ +* PWM beeper device tree bindings + +Registers a PWM device as beeper. + +Required properties: +- compatible: should be "pwm-beeper" +- pwms: phandle to the physical PWM device + +Optional properties: +- amp-supply: phandle to a regulator that acts as an amplifier for the beeper +- beeper-hz: bell frequency in Hz + +Example: + +beeper_amp: amplifier { + compatible = "fixed-regulator"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; +}; + +beeper { + compatible = "pwm-beeper"; + pwms = <&pwm0>; + amp-supply = <&beeper_amp>; +}; diff --git a/Documentation/devicetree/bindings/input/pwm-vibrator.yaml b/Documentation/devicetree/bindings/input/pwm-vibrator.yaml new file mode 100644 index 000000000..a70a636ee --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-vibrator.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/input/pwm-vibrator.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: PWM vibrator + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: > + Registers a PWM device as vibrator. It is expected, that the vibrator's + strength increases based on the duty cycle of the enable PWM channel + (100% duty cycle meaning strongest vibration, 0% meaning no vibration). + + The binding supports an optional direction PWM channel, that can be + driven at fixed duty cycle. If available this is can be used to increase + the vibration effect of some devices. + +properties: + compatible: + const: pwm-vibrator + + pwm-names: + items: + - const: enable + - const: direction + minItems: 1 + + pwms: + minItems: 1 + maxItems: 2 + + vcc-supply: true + + direction-duty-cycle-ns: + description: > + Duty cycle of the direction PWM channel in nanoseconds, + defaults to 50% of the channel's period. + +required: + - compatible + - pwm-names + - pwms + +additionalProperties: false + +examples: + - | + vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm9 0 1000000000 0>, + <&pwm8 0 1000000000 0>; + pwm-names = "enable", "direction"; + direction-duty-cycle-ns = <1000000000>; + }; diff --git a/Documentation/devicetree/bindings/input/pxa27x-keypad.txt b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt new file mode 100644 index 000000000..f8674f7e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt @@ -0,0 +1,60 @@ +* Marvell PXA Keypad controller + +Required Properties +- compatible : should be "marvell,pxa27x-keypad" +- reg : Address and length of the register set for the device +- interrupts : The interrupt for the keypad controller +- marvell,debounce-interval : How long time the key will be + recognized when it is pressed. It is a u32 value, and bit[31:16] + is debounce interval for direct key and bit[15:0] is debounce + interval for matrix key. The value is in binary number of 2ms + +Optional Properties For Matrix Keyes +Please refer to matrix-keymap.txt + +Optional Properties for Direct Keyes +- marvell,direct-key-count : How many direct keyes are used. +- marvell,direct-key-mask : The mask indicates which keyes + are used. If bit[X] of the mask is set, the direct key X + is used. +- marvell,direct-key-low-active : Direct key status register + tells the level of pins that connects to the direct keyes. + When this property is set, it means that when the pin level + is low, the key is pressed(active). +- marvell,direct-key-map : It is a u16 array. Each item indicates + the linux key-code for the direct key. + +Optional Properties For Rotary +- marvell,rotary0 : It is a u32 value. Bit[31:16] is the + linux key-code for rotary up. Bit[15:0] is the linux key-code + for rotary down. It is for rotary 0. +- marvell,rotary1 : Same as marvell,rotary0. It is for rotary 1. +- marvell,rotary-rel-key : When rotary is used for relative axes + in the device, the value indicates the key-code for relative + axes measurement in the device. It is a u32 value. Bit[31:16] + is for rotary 1, and Bit[15:0] is for rotary 0. + +Examples: + keypad: keypad@d4012000 { + keypad,num-rows = <3>; + keypad,num-columns = <5>; + linux,keymap = <0x0000000e /* KEY_BACKSPACE */ + 0x0001006b /* KEY_END */ + 0x00020061 /* KEY_RIGHTCTRL */ + 0x0003000b /* KEY_0 */ + 0x00040002 /* KEY_1 */ + 0x0100008b /* KEY_MENU */ + 0x01010066 /* KEY_HOME */ + 0x010200e7 /* KEY_SEND */ + 0x01030009 /* KEY_8 */ + 0x0104000a /* KEY_9 */ + 0x02000160 /* KEY_OK */ + 0x02010003 /* KEY_2 */ + 0x02020004 /* KEY_3 */ + 0x02030005 /* KEY_4 */ + 0x02040006>; /* KEY_5 */ + marvell,rotary0 = <0x006c0067>; /* KEY_UP & KEY_DOWN */ + marvell,direct-key-count = <1>; + marvell,direct-key-map = <0x001c>; + marvell,debounce-interval = <0x001e001e>; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.yaml b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.yaml new file mode 100644 index 000000000..62314a5fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/qcom,pm8941-pwrkey.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm PM8941 PMIC Power Key + +maintainers: + - Courtney Cavin <courtney.cavin@sonymobile.com> + - Vinod Koul <vkoul@kernel.org> + +allOf: + - $ref: input.yaml# + +properties: + compatible: + enum: + - qcom,pm8941-pwrkey + - qcom,pm8941-resin + - qcom,pmk8350-pwrkey + - qcom,pmk8350-resin + + interrupts: + maxItems: 1 + + debounce: + description: | + Time in microseconds that key must be pressed or + released for state change interrupt to trigger. + $ref: /schemas/types.yaml#/definitions/uint32 + + bias-pull-up: + description: | + Presence of this property indicates that the KPDPWR_N + pin should be configured for pull up. + $ref: /schemas/types.yaml#/definitions/flag + + linux,code: + description: | + The input key-code associated with the power key. + Use the linux event codes defined in + include/dt-bindings/input/linux-event-codes.h + When property is omitted KEY_POWER is assumed. + +required: + - compatible + - interrupts + +unevaluatedProperties: false +... diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt new file mode 100644 index 000000000..4a9dc6ba9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt @@ -0,0 +1,90 @@ +Qualcomm PM8xxx PMIC Keypad + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-keypad" + "qcom,pm8921-keypad" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of keypad control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key sense interrupt + and the second interrupt specifies the key stuck interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- linux,keymap: + Usage: required + Value type: <prop-encoded-array> + Definition: the linux keymap. More information can be found in + input/matrix-keymap.txt. + +- linux,keypad-no-autorepeat: + Usage: optional + Value type: <bool> + Definition: don't enable autorepeat feature. + +- wakeup-source: + Usage: optional + Value type: <bool> + Definition: use any event on keypad as wakeup event. + (Legacy property supported: "linux,keypad-wakeup") + +- keypad,num-rows: + Usage: required + Value type: <u32> + Definition: number of rows in the keymap. More information can be found + in input/matrix-keymap.txt. + +- keypad,num-columns: + Usage: required + Value type: <u32> + Definition: number of columns in the keymap. More information can be + found in input/matrix-keymap.txt. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for key sense interrupt to trigger. + +- scan-delay: + Usage: optional + Value type: <u32> + Definition: time in microseconds to pause between successive scans + of the matrix array. + +- row-hold: + Usage: optional + Value type: <u32> + Definition: time in nanoseconds to pause between scans of each row in + the matrix array. + +EXAMPLE + + keypad@148 { + compatible = "qcom,pm8921-keypad"; + reg = <0x148>; + interrupt-parent = <&pmicintc>; + interrupts = <74 1>, <75 1>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_VOLUMEUP) + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN) + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS) + MATRIX_KEY(0, 3, KEY_CAMERA) + >; + keypad,num-rows = <1>; + keypad,num-columns = <5>; + debounce = <15>; + scan-delay = <32>; + row-hold = <91500>; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt new file mode 100644 index 000000000..588536cc9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt @@ -0,0 +1,46 @@ +Qualcomm PM8xxx PMIC Power Key + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-pwrkey" + "qcom,pm8921-pwrkey" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of power key control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key release interrupt + and the second interrupt specifies the key press interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for state change interrupt to trigger. + +- pull-up: + Usage: optional + Value type: <empty> + Definition: presence of this property indicates that the KPDPWR_N pin + should be configured for pull up. + +EXAMPLE + + pwrkey@1c { + compatible = "qcom,pm8921-pwrkey"; + reg = <0x1c>; + interrupt-parent = <&pmicintc>; + interrupts = <50 1>, <51 1>; + debounce = <15625>; + pull-up; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml new file mode 100644 index 000000000..c8832cd0d --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml @@ -0,0 +1,38 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/qcom,pm8xxx-vib.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm PM8xxx PMIC Vibrator + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + +properties: + compatible: + enum: + - qcom,pm8058-vib + - qcom,pm8916-vib + - qcom,pm8921-vib + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pmic { + #address-cells = <1>; + #size-cells = <0>; + + vibrator@4a { + compatible = "qcom,pm8058-vib"; + reg = <0x4a>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt new file mode 100644 index 000000000..99a4f2ab5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/raydium_i2c_ts.txt @@ -0,0 +1,19 @@ +Raydium I2C touchscreen + +Required properties: +- compatible: must be "raydium,rm32380" +- reg: The I2C address of the device +- interrupts: interrupt to which the chip is connected + See ../interrupt-controller/interrupts.txt +Optional properties: +- avdd-supply: analog power supply needed to power device +- vccio-supply: IO Power source +- reset-gpios: reset gpio the chip is connected to. + +Example: + touchscreen@39 { + compatible = "raydium,rm32380"; + reg = <0x39>; + interrupt-parent = <&gpio>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/input/regulator-haptic.yaml b/Documentation/devicetree/bindings/input/regulator-haptic.yaml new file mode 100644 index 000000000..627891e1e --- /dev/null +++ b/Documentation/devicetree/bindings/input/regulator-haptic.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/input/regulator-haptic.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Regulator Haptic + +maintainers: + - Jaewon Kim <jaewon02.kim@samsung.com> + +properties: + compatible: + const: regulator-haptic + + haptic-supply: + description: > + Power supply to the haptic motor + + max-microvolt: + description: > + The maximum voltage value supplied to the haptic motor + + min-microvolt: + description: > + The minimum voltage value supplied to the haptic motor + +required: + - compatible + - haptic-supply + - max-microvolt + - min-microvolt + +additionalProperties: false + +examples: + - | + haptics { + compatible = "regulator-haptic"; + haptic-supply = <&motor_regulator>; + max-microvolt = <2700000>; + min-microvolt = <1100000>; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt new file mode 100644 index 000000000..9afffbdf6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt @@ -0,0 +1,56 @@ +Synaptics RMI4 2D Sensor Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices which contain 2D sensors using Function 11 or +Function 12. Complete documentation for transports and other functions +can be found in: +Documentation/devicetree/bindings/input/rmi4. + +RMI4 Function 11 and Function 12 are for 2D touch position sensing. +Additional documentation for F11 can be found at: +http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf + +Optional Touch Properties: +Description in Documentation/devicetree/bindings/input/touchscreen +- touchscreen-inverted-x +- touchscreen-inverted-y +- touchscreen-swapped-x-y +- touchscreen-x-mm +- touchscreen-y-mm + +Optional Properties: +- syna,clip-x-low: Sets a minimum value for X. +- syna,clip-y-low: Sets a minimum value for Y. +- syna,clip-x-high: Sets a maximum value for X. +- syna,clip-y-high: Sets a maximum value for Y. +- syna,offset-x: Add an offset to X. +- syna,offset-y: Add an offset to Y. +- syna,delta-x-threshold: Set the minimum distance on the X axis required + to generate an interrupt in reduced reporting + mode. +- syna,delta-y-threshold: Set the minimum distance on the Y axis required + to generate an interrupt in reduced reporting + mode. +- syna,sensor-type: Set the sensor type. 1 for touchscreen 2 for touchpad. +- syna,disable-report-mask: Mask for disabling posiiton reporting. Used to + disable reporing absolute position data. +- syna,rezero-wait-ms: Time in miliseconds to wait after issuing a rezero + command. + + +Example of a RMI4 I2C device with F11: +Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + + ... + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt new file mode 100644 index 000000000..079cad2b6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt @@ -0,0 +1,39 @@ +Synaptics RMI4 F01 Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices which contain Function 1. Complete documentation +for transports and other functions can be found in: +Documentation/devicetree/bindings/input/rmi4. + +Additional documentation for F01 can be found at: +http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf + +Optional Properties: +- syna,nosleep-mode: If set the device will run at full power without sleeping. + nosleep has 3 modes, 0 will not change the default + setting, 1 will disable nosleep (allow sleeping), + and 2 will enable nosleep (disabling sleep). +- syna,wakeup-threshold: Defines the amplitude of the disturbance to the + background capacitance that will cause the + device to wake from dozing. +- syna,doze-holdoff-ms: The delay to wait after the last finger lift and the + first doze cycle. +- syna,doze-interval-ms: The time period that the device sleeps between finger + activity. + + +Example of a RMI4 I2C device with F01: + Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + + ... + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt new file mode 100644 index 000000000..dcb012f5b --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt @@ -0,0 +1,61 @@ +Synaptics RMI4 I2C Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices using the I2C transport driver. Complete documentation +for other transports and functions can be found in +Documentation/devicetree/bindings/input/rmi4. + +Required Properties: +- compatible: syna,rmi4-i2c +- reg: I2C address +- #address-cells: Set to 1 to indicate that the function child nodes + consist of only on uint32 value. +- #size-cells: Set to 0 to indicate that the function child nodes do not + have a size property. + +Optional Properties: +- interrupts: interrupt which the rmi device is connected to. +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- syna,reset-delay-ms: The number of milliseconds to wait after resetting the + device. + +- syna,startup-delay-ms: The number of milliseconds to wait after powering on + the device. + +- vdd-supply: VDD power supply. +See ../regulator/regulator.txt + +- vio-supply: VIO power supply +See ../regulator/regulator.txt + +Function Parameters: +Parameters specific to RMI functions are contained in child nodes of the rmi device + node. Documentation for the parameters of each function can be found in: +Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. + + + +Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + reg = <0x2c>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio>; + interrupts = <4 2>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt new file mode 100644 index 000000000..632f473db --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt @@ -0,0 +1,56 @@ +Synaptics RMI4 SPI Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices using the SPI transport driver. Complete documentation +for other transports and functions can be found in +Documentation/devicetree/bindings/input/rmi4. + +Required Properties: +- compatible: syna,rmi4-spi +- reg: Chip select address for the device +- #address-cells: Set to 1 to indicate that the function child nodes + consist of only on uint32 value. +- #size-cells: Set to 0 to indicate that the function child nodes do not + have a size property. + +Optional Properties: +- interrupts: interrupt which the rmi device is connected to. +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- spi-rx-delay-us: microsecond delay after a read transfer. +- spi-tx-delay-us: microsecond delay after a write transfer. + +Function Parameters: +Parameters specific to RMI functions are contained in child nodes of the rmi device + node. Documentation for the parameters of each function can be found in: +Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. + + + +Example: + spi@7000d800 { + rmi4-spi-dev@0 { + compatible = "syna,rmi4-spi"; + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <4000000>; + spi-cpha; + spi-cpol; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(K, 2) 0x2>; + spi-rx-delay-us = <30>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt new file mode 100644 index 000000000..a644408b3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -0,0 +1,50 @@ +Rotary encoder DT bindings + +Required properties: +- gpios: a spec for at least two GPIOs to be used, most significant first + +Optional properties: +- linux,axis: the input subsystem axis to map to this rotary encoder. + Defaults to 0 (ABS_X / REL_X) +- rotary-encoder,steps: Number of steps in a full turnaround of the + encoder. Only relevant for absolute axis. Defaults to 24 which is a + typical value for such devices. +- rotary-encoder,relative-axis: register a relative axis rather than an + absolute one. Relative axis will only generate +1/-1 events on the input + device, hence no steps need to be passed. +- rotary-encoder,rollover: Automatic rollover when the rotary value becomes + greater than the specified steps or smaller than 0. For absolute axis only. +- rotary-encoder,steps-per-period: Number of steps (stable states) per period. + The values have the following meaning: + 1: Full-period mode (default) + 2: Half-period mode + 4: Quarter-period mode +- wakeup-source: Boolean, rotary encoder can wake up the system. +- rotary-encoder,encoding: String, the method used to encode steps. + Supported are "gray" (the default and more common) and "binary". + +Deprecated properties: +- rotary-encoder,half-period: Makes the driver work on half-period mode. + This property is deprecated. Instead, a 'steps-per-period ' value should + be used, such as "rotary-encoder,steps-per-period = <2>". + +See Documentation/input/devices/rotary-encoder.rst for more information. + +Example: + + rotary@0 { + compatible = "rotary-encoder"; + gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */ + linux,axis = <0>; /* REL_X */ + rotary-encoder,encoding = "gray"; + rotary-encoder,relative-axis; + }; + + rotary@1 { + compatible = "rotary-encoder"; + gpios = <&gpio 21 0>, <&gpio 22 0>; + linux,axis = <1>; /* ABS_Y */ + rotary-encoder,steps = <24>; + rotary-encoder,encoding = "binary"; + rotary-encoder,rollover; + }; diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt new file mode 100644 index 000000000..4c5c0a825 --- /dev/null +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -0,0 +1,77 @@ +* Samsung's Keypad Controller device tree bindings + +Samsung's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad + controller. + - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad + controller. + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Required Board Specific Properties: +- samsung,keypad-num-rows: Number of row lines connected to the keypad + controller. + +- samsung,keypad-num-columns: Number of column lines connected to the + keypad controller. + +- Keys represented as child nodes: Each key connected to the keypad + controller is represented as a child node to the keypad controller + device node and should include the following properties. + - keypad,row: the row number to which the key is connected. + - keypad,column: the column number to which the key is connected. + - linux,code: the key-code to be reported when the key is pressed + and released. + +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + +Optional Properties: +- wakeup-source: use any event on keypad as wakeup event. + (Legacy property supported: "linux,input-wakeup") + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. + + +Example: + keypad@100a0000 { + compatible = "samsung,s5pv210-keypad"; + reg = <0x100A0000 0x100>; + interrupts = <173>; + samsung,keypad-num-rows = <2>; + samsung,keypad-num-columns = <8>; + linux,input-no-autorepeat; + wakeup-source; + + pinctrl-names = "default"; + pinctrl-0 = <&keypad_rows &keypad_columns>; + + key_1 { + keypad,row = <0>; + keypad,column = <3>; + linux,code = <2>; + }; + + key_2 { + keypad,row = <0>; + keypad,column = <4>; + linux,code = <3>; + }; + + key_3 { + keypad,row = <0>; + keypad,column = <5>; + linux,code = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/snvs-pwrkey.txt b/Documentation/devicetree/bindings/input/snvs-pwrkey.txt new file mode 100644 index 000000000..70c142503 --- /dev/null +++ b/Documentation/devicetree/bindings/input/snvs-pwrkey.txt @@ -0,0 +1 @@ +See Documentation/devicetree/bindings/crypto/fsl-sec4.txt diff --git a/Documentation/devicetree/bindings/input/spear-keyboard.txt b/Documentation/devicetree/bindings/input/spear-keyboard.txt new file mode 100644 index 000000000..4a846d26d --- /dev/null +++ b/Documentation/devicetree/bindings/input/spear-keyboard.txt @@ -0,0 +1,20 @@ +* SPEAr keyboard controller + +Required properties: +- compatible: "st,spear300-kbd" + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: +- autorepeat: bool: enables key autorepeat +- st,mode: keyboard mode: 0 - 9x9, 1 - 6x6, 2 - 2x2 + +Example: + +kbd@fc400000 { + compatible = "st,spear300-kbd"; + reg = <0xfc400000 0x100>; + linux,keymap = < 0x00030012 + 0x0102003a >; + autorepeat; + st,mode = <0>; +}; diff --git a/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml b/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml new file mode 100644 index 000000000..a401a0bfc --- /dev/null +++ b/Documentation/devicetree/bindings/input/sprd,sc27xx-vibrator.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2020 Unisoc Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/sprd,sc27xx-vibrator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Spreadtrum SC27xx PMIC Vibrator + +maintainers: + - Orson Zhai <orsonzhai@gmail.com> + - Baolin Wang <baolin.wang7@gmail.com> + - Chunyan Zhang <zhang.lyra@gmail.com> + +properties: + compatible: + enum: + - sprd,sc2721-vibrator + - sprd,sc2730-vibrator + - sprd,sc2731-vibrator + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0 0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + + vibrator@eb4 { + compatible = "sprd,sc2731-vibrator"; + reg = <0xeb4>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/st-keyscan.txt b/Documentation/devicetree/bindings/input/st-keyscan.txt new file mode 100644 index 000000000..51eb428e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/st-keyscan.txt @@ -0,0 +1,60 @@ +* ST Keyscan controller Device Tree bindings + +The ST keyscan controller Device Tree binding is based on the +matrix-keymap. + +Required properties: +- compatible: "st,sti-keyscan" + +- reg: Register base address and size of st-keyscan controller. + +- interrupts: Interrupt number for the st-keyscan controller. + +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +- pinctrl: Should specify pin control groups used for this controller. + See ../pinctrl/pinctrl-bindings.txt for details. + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +- keypad,num-rows: Number of row lines connected to the keypad controller. + +- keypad,num-columns: Number of column lines connected to the keypad + controller. + +Optional property: +- st,debounce_us: Debouncing interval time in microseconds + +Example: + +keyscan: keyscan@fe4b0000 { + compatible = "st,sti-keyscan"; + reg = <0xfe4b0000 0x2000>; + interrupts = <GIC_SPI 212 IRQ_TYPE_NONE>; + clocks = <&CLK_SYSIN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_keyscan>; + + keypad,num-rows = <4>; + keypad,num-columns = <4>; + st,debounce_us = <5000>; + + linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_F13) + MATRIX_KEY(0x00, 0x01, KEY_F9) + MATRIX_KEY(0x00, 0x02, KEY_F5) + MATRIX_KEY(0x00, 0x03, KEY_F1) + MATRIX_KEY(0x01, 0x00, KEY_F14) + MATRIX_KEY(0x01, 0x01, KEY_F10) + MATRIX_KEY(0x01, 0x02, KEY_F6) + MATRIX_KEY(0x01, 0x03, KEY_F2) + MATRIX_KEY(0x02, 0x00, KEY_F15) + MATRIX_KEY(0x02, 0x01, KEY_F11) + MATRIX_KEY(0x02, 0x02, KEY_F7) + MATRIX_KEY(0x02, 0x03, KEY_F3) + MATRIX_KEY(0x03, 0x00, KEY_F16) + MATRIX_KEY(0x03, 0x01, KEY_F12) + MATRIX_KEY(0x03, 0x02, KEY_F8) + MATRIX_KEY(0x03, 0x03, KEY_F4) >; + }; diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt new file mode 100644 index 000000000..12bb771d6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -0,0 +1,41 @@ +* STMPE Keypad + +Required properties: + - compatible : "st,stmpe-keypad" + - linux,keymap : See ./matrix-keymap.txt + +Optional properties: + - debounce-interval : Debouncing interval time in milliseconds + - st,scan-count : Scanning cycles elapsed before key data is updated + - st,no-autorepeat : If specified device will not autorepeat + - keypad,num-rows : See ./matrix-keymap.txt + - keypad,num-columns : See ./matrix-keymap.txt + +Example: + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt new file mode 100644 index 000000000..255185009 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -0,0 +1,10 @@ +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required properties: +- compatible: "ti,tca8418" +- reg: the I2C address +- interrupts: IRQ line number, should trigger on falling edge +- linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt new file mode 100644 index 000000000..4c5312eaa --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -0,0 +1,50 @@ +* Texas Instruments - drv260x Haptics driver family + +Required properties: + - compatible - One of: + "ti,drv2604" - DRV2604 + "ti,drv2605" - DRV2605 + "ti,drv2605l" - DRV2605L + - reg - I2C slave address + - vbat-supply - Required supply regulator + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) + DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration + sequence during init. And the device is configured for real + time playback mode (RTP mode). + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) + - library-sel - These are ROM based waveforms pre-programmed into the IC. + This should be set to set the library to use at power up. + (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LIB_EMPTY - Do not use a pre-programmed library + DRV260X_ERM_LIB_A - Pre-programmed Library + DRV260X_ERM_LIB_B - Pre-programmed Library + DRV260X_ERM_LIB_C - Pre-programmed Library + DRV260X_ERM_LIB_D - Pre-programmed Library + DRV260X_ERM_LIB_E - Pre-programmed Library + DRV260X_ERM_LIB_F - Pre-programmed Library + DRV260X_LIB_LRA - Pre-programmed LRA Library + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - vib-rated-mv - The rated voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. + - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. +Example: + +haptics: haptics@5a { + compatible = "ti,drv2605l"; + reg = <0x5a>; + vbat-supply = <&vbat>; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + mode = <DRV260X_LRA_MODE>; + library-sel = <DRV260X_LIB_LRA>; + vib-rated-mv = <3200>; + vib-overdrive-mv = <3200>; +} + +For more product information please see the link below: +http://www.ti.com/product/drv2605 diff --git a/Documentation/devicetree/bindings/input/ti,drv2665.txt b/Documentation/devicetree/bindings/input/ti,drv2665.txt new file mode 100644 index 000000000..1ba97ac04 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2665.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2665 Haptics driver + +Required properties: + - compatible - "ti,drv2665" - DRV2665 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2665"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2665 diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt new file mode 100644 index 000000000..996382cf9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2667.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2667 Haptics driver + +Required properties: + - compatible - "ti,drv2667" - DRV2667 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2667"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2667 diff --git a/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt new file mode 100644 index 000000000..513d94d6e --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt @@ -0,0 +1,60 @@ +TI-NSPIRE Keypad + +Required properties: +- compatible: Compatible property value should be "ti,nspire-keypad". + +- reg: Physical base address of the peripheral and length of memory mapped + region. + +- interrupts: The interrupt number for the peripheral. + +- scan-interval: How often to scan in us. Based on a APB speed of 33MHz, the + maximum and minimum delay time is ~2000us and ~500us respectively + +- row-delay: How long to wait before scanning each row. + +- clocks: The clock this peripheral is attached to. + +- linux,keymap: The keymap to use + (see Documentation/devicetree/bindings/input/matrix-keymap.txt) + +Optional properties: +- active-low: Specify that the keypad is active low (i.e. logical low signifies + a key press). + +Example: + +input { + compatible = "ti,nspire-keypad"; + reg = <0x900E0000 0x1000>; + interrupts = <16>; + + scan-interval = <1000>; + row-delay = <200>; + + clocks = <&apb_pclk>; + + linux,keymap = < + 0x0000001c 0x0001001c 0x00040039 + 0x0005002c 0x00060015 0x0007000b + 0x0008000f 0x0100002d 0x01010011 + 0x0102002f 0x01030004 0x01040016 + 0x01050014 0x0106001f 0x01070002 + 0x010a006a 0x02000013 0x02010010 + 0x02020019 0x02030007 0x02040018 + 0x02050031 0x02060032 0x02070005 + 0x02080028 0x0209006c 0x03000026 + 0x03010025 0x03020024 0x0303000a + 0x03040017 0x03050023 0x03060022 + 0x03070008 0x03080035 0x03090069 + 0x04000021 0x04010012 0x04020020 + 0x0404002e 0x04050030 0x0406001e + 0x0407000d 0x04080037 0x04090067 + 0x05010038 0x0502000c 0x0503001b + 0x05040034 0x0505001a 0x05060006 + 0x05080027 0x0509000e 0x050a006f + 0x0600002b 0x0602004e 0x06030068 + 0x06040003 0x0605006d 0x06060009 + 0x06070001 0x0609000f 0x0708002a + 0x0709001d 0x070a0033 >; +}; diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt new file mode 100644 index 000000000..c829e18e1 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt @@ -0,0 +1,35 @@ +Texas Instruments Palmas family power button module + +This module is part of the Palmas family of PMICs. For more details +about the whole chip see: +Documentation/devicetree/bindings/mfd/palmas.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,palmas-pwrbutton": For Palmas compatible power on button +- interrupts: Interrupt number of power button submodule on device. + +Optional Properties: + +- ti,palmas-long-press-seconds: Duration in seconds which the power + button should be kept pressed for Palmas to power off automatically. + NOTE: This depends on OTP support and POWERHOLD signal configuration + on platform. Valid values are 6, 8, 10 and 12. +- ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds + which the power button should be kept pressed for Palmas to register + a press for debouncing purposes. NOTE: This depends on specific + Palmas variation capability. Valid values are 15, 100, 500 and 1000. + +Example: + +&palmas { + palmas_pwr_button: pwrbutton { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + ti,palmas-long-press-seconds = <12>; + ti,palmas-pwron-debounce-milli-seconds = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt new file mode 100644 index 000000000..afa38dc06 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -0,0 +1,71 @@ +* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) + +Required properties: +- compatible : for SPI slave, use "adi,ad7879" + for I2C slave, use "adi,ad7879-1" +- reg : SPI chipselect/I2C slave address + See spi-bus.txt for more SPI slave properties +- interrupts : touch controller interrupt +- touchscreen-max-pressure : maximum reported pressure +- adi,resistance-plate-x : total resistance of X-plate (for pressure + calculation) +Optional properties: +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) +- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) + 13 : 2.560ms + 14 : 3.584ms + 15 : 4.096ms + This property has to be a '/bits/ 8' value +- adi,acquisition-time : 0: 2us + 1: 4us + 2: 8us + 3: 16us + This property has to be a '/bits/ 8' value +- adi,median-filter-size : 0: disabled + 1: 4 measurements + 2: 8 measurements + 3: 16 measurements + This property has to be a '/bits/ 8' value +- adi,averaging : 0: 2 middle values (1 if median disabled) + 1: 4 middle values + 2: 8 middle values + 3: 16 values + This property has to be a '/bits/ 8' value +- adi,conversion-interval: : 0 : convert one time only + 1-255: 515us + val * 35us (up to 9.440ms) + This property has to be a '/bits/ 8' value +- gpio-controller : Switch AUX/VBAT/GPIO pin to GPIO mode + +Example: + + touchscreen0@2c { + compatible = "adi,ad7879-1"; + reg = <0x2c>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; + + touchscreen1@1 { + compatible = "adi,ad7879"; + spi-max-frequency = <5000000>; + reg = <1>; + spi-cpol; + spi-cpha; + gpio-controller; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt new file mode 100644 index 000000000..81f6bda97 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ads7846.txt @@ -0,0 +1,106 @@ +Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046 +SPI driven touch screen controllers. + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Additional required properties: + + compatible Must be one of the following, depending on the + model: + "ti,tsc2046" + "ti,ads7843" + "ti,ads7845" + "ti,ads7846" + "ti,ads7873" + + interrupts An interrupt node describing the IRQ line the chip's + !PENIRQ pin is connected to. + vcc-supply A regulator node for the supply voltage. + + +Optional properties: + + ti,vref-delay-usecs vref supply delay in usecs, 0 for + external vref (u16). + ti,vref-mv The VREF voltage, in millivolts (u16). + Set to 0 to use internal references + (ADS7846). + ti,keep-vref-on set to keep vref on for differential + measurements as well + ti,settle-delay-usec Settling time of the analog signals; + a function of Vcc and the capacitance + on the X/Y drivers. If set to non-zero, + two samples are taken with settle_delay + us apart, and the second one is used. + ~150 uSec with 0.01uF caps (u16). + ti,penirq-recheck-delay-usecs If set to non-zero, after samples are + taken this delay is applied and penirq + is rechecked, to help avoid false + events. This value is affected by the + material used to build the touch layer + (u16). + ti,x-plate-ohms Resistance of the X-plate, + in Ohms (u16). + ti,y-plate-ohms Resistance of the Y-plate, + in Ohms (u16). + ti,x-min Minimum value on the X axis (u16). + ti,y-min Minimum value on the Y axis (u16). + ti,debounce-tol Tolerance used for filtering (u16). + ti,debounce-rep Additional consecutive good readings + required after the first two (u16). + ti,pendown-gpio-debounce Platform specific debounce time for the + pendown-gpio (u32). + pendown-gpio GPIO handle describing the pin the !PENIRQ + line is connected to. + wakeup-source use any event on touchscreen as wakeup event. + (Legacy property support: "linux,wakeup") + touchscreen-size-x General touchscreen binding, see [1]. + touchscreen-size-y General touchscreen binding, see [1]. + touchscreen-max-pressure General touchscreen binding, see [1]. + touchscreen-min-pressure General touchscreen binding, see [1]. + touchscreen-average-samples General touchscreen binding, see [1]. + touchscreen-inverted-x General touchscreen binding, see [1]. + touchscreen-inverted-y General touchscreen binding, see [1]. + touchscreen-swapped-x-y General touchscreen binding, see [1]. + +[1] All general touchscreen properties are described in + Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt. + +Deprecated properties: + + ti,swap-xy swap x and y axis + ti,x-max Maximum value on the X axis (u16). + ti,y-max Maximum value on the Y axis (u16). + ti,pressure-min Minimum reported pressure value + (threshold) - u16. + ti,pressure-max Maximum reported pressure value (u16). + ti,debounce-max Max number of additional readings per + sample (u16). + +Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: + + spi_controller { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* BOOT6 / GPIO 8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt new file mode 100644 index 000000000..82019bd60 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ar1021.txt @@ -0,0 +1,15 @@ +* Microchip AR1020 and AR1021 touchscreen interface (I2C) + +Required properties: +- compatible : "microchip,ar1021-i2c" +- reg : I2C slave address +- interrupts : touch controller interrupt + +Example: + + touchscreen@4d { + compatible = "microchip,ar1021-i2c"; + reg = <0x4d>; + interrupt-parent = <&gpio3>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt new file mode 100644 index 000000000..b8db975e9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt @@ -0,0 +1,30 @@ +* AUO in-cell touchscreen controller using Pixcir sensors + +Required properties: +- compatible: must be "auo,auo_pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + auo_pixcir_ts@5c { + compatible = "auo,auo_pixcir_ts"; + reg = <0x5c>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + gpios = <&gpf 2 0 GPIO_LEVEL_HIGH>, /* INT */ + <&gpf 5 1 GPIO_LEVEL_LOW>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml new file mode 100644 index 000000000..b5f377215 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs5xx.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/azoteq,iqs5xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS550/572/525 Trackpad/Touchscreen Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS550, IQS572 and IQS525 trackpad and touchscreen controllers + employ projected-capacitance sensing and can track up to five independent + contacts. + + Link to datasheet: https://www.azoteq.com/ + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - azoteq,iqs550 + - azoteq,iqs572 + - azoteq,iqs525 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + wakeup-source: true + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@74 { + compatible = "azoteq,iqs550"; + reg = <0x74>; + interrupt-parent = <&gpio>; + interrupts = <27 IRQ_TYPE_LEVEL_HIGH>; + reset-gpios = <&gpio 22 (GPIO_ACTIVE_LOW | + GPIO_PUSH_PULL)>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt new file mode 100644 index 000000000..f127a2117 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -0,0 +1,87 @@ +* Broadcom's IPROC Touchscreen Controller + +Required properties: +- compatible: must be "brcm,iproc-touchscreen" +- ts_syscon: handler of syscon node defining physical base + address of the controller and length of memory mapped region. + If this property is selected please make sure MFD_SYSCON config + is enabled in the defconfig file. +- clocks: The clock provided by the SOC to driver the tsc +- clock-names: name for the clock +- interrupts: The touchscreen controller's interrupt +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: Specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. + +Optional properties: +- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. +- debounce_timeout: Each step is 512 us. Valid 0-255 +- settling_timeout: The settling duration (in ms) is the amount of time + the tsc waits to allow the voltage to settle after + turning on the drivers in detection mode. + Valid values: 0-11 + 0 = 0.008 ms + 1 = 0.01 ms + 2 = 0.02 ms + 3 = 0.04 ms + 4 = 0.08 ms + 5 = 0.16 ms + 6 = 0.32 ms + 7 = 0.64 ms + 8 = 1.28 ms + 9 = 2.56 ms + 10 = 5.12 ms + 11 = 10.24 ms +- touch_timeout: The continuous number of scan periods in which touch is + not detected before the controller returns to idle state. + Valid values 0-255. +- average_data: Number of data samples which are averaged before a final + data point is placed into the FIFO + Valid values 0-7 + 0 = 1 sample + 1 = 2 samples + 2 = 4 samples + 3 = 8 samples + 4 = 16 samples + 5 = 32 samples + 6 = 64 samples + 7 = 128 samples +- fifo_threshold: Interrupt is generated whenever the number of fifo + entries exceeds this value + Valid values 0-31 +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) +- touchscreen-fuzz-x: horizontal noise value of the absolute input + device (in pixels) +- touchscreen-fuzz-y: vertical noise value of the absolute input + device (in pixels) +- touchscreen-inverted-x: X axis is inverted (boolean) +- touchscreen-inverted-y: Y axis is inverted (boolean) + +Example: An example of touchscreen node + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + touchscreen: touchscreen@180a6000 { + compatible = "brcm,iproc-touchscreen"; + #address-cells = <1>; + #size-cells = <1>; + ts_syscon = <&ts_adc_syscon>; + clocks = <&adc_clk>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + + scanning_period = <5>; + debounce_timeout = <40>; + settling_timeout = <7>; + touch_timeout = <10>; + average_data = <5>; + fifo_threshold = <1>; + /* Touchscreen is rotated 180 degrees. */ + touchscreen-inverted-x; + touchscreen-inverted-y; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt new file mode 100644 index 000000000..da4c9d8b9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -0,0 +1,43 @@ +* Rohm BU21013 Touch Screen + +Required properties: + - compatible : "rohm,bu21013_tp" + - reg : I2C device address + - reset-gpios : GPIO pin enabling (selecting) chip (CS) + - interrupt-parent : the phandle for the gpio controller + - interrupts : (gpio) interrupt to which the chip is connected + +Optional properties: + - touch-gpios : GPIO pin registering a touch event + - <supply_name>-supply : Phandle to a regulator supply + - touchscreen-size-x : General touchscreen binding, see [1]. + - touchscreen-size-y : General touchscreen binding, see [1]. + - touchscreen-inverted-x : General touchscreen binding, see [1]. + - touchscreen-inverted-y : General touchscreen binding, see [1]. + - touchscreen-swapped-x-y : General touchscreen binding, see [1]. + +[1] All general touchscreen properties are described in + Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt. + +Deprecated properties: + - rohm,touch-max-x : Maximum outward permitted limit in the X axis + - rohm,touch-max-y : Maximum outward permitted limit in the Y axis + - rohm,flip-x : Flip touch coordinates on the X axis + - rohm,flip-y : Flip touch coordinates on the Y axis + +Example: + + i2c@80110000 { + bu21013_tp@5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + interrupt-parent = <&gpio2>; + interrupts <&20 IRQ_TYPE_LEVEL_LOW>; + touch-gpio = <&gpio2 20 GPIO_ACTIVE_LOW>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + touchscreen-size-x = <384>; + touchscreen-size-y = <704>; + touchscreen-inverted-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt new file mode 100644 index 000000000..8daa0e868 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt @@ -0,0 +1,35 @@ +* Rohm BU21029 Touch Screen Controller + +Required properties: + - compatible : must be "rohm,bu21029" + - reg : i2c device address of the chip (0x40 or 0x41) + - interrupt-parent : the phandle for the gpio controller + - interrupts : (gpio) interrupt to which the chip is connected + - rohm,x-plate-ohms : x-plate resistance in Ohm + +Optional properties: + - reset-gpios : gpio pin to reset the chip (active low) + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-max-pressure: maximum pressure value + - vdd-supply : power supply for the controller + +Example: + + &i2c1 { + /* ... */ + + bu21029: bu21029@40 { + compatible = "rohm,bu21029"; + reg = <0x40>; + interrupt-parent = <&gpio1>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; + rohm,x-plate-ohms = <600>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-max-pressure = <4095>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/chipone,icn8318.yaml b/Documentation/devicetree/bindings/input/touchscreen/chipone,icn8318.yaml new file mode 100644 index 000000000..9df685bdc --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/chipone,icn8318.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/chipone,icn8318.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ChipOne ICN8318 Touchscreen Controller Device Tree Bindings + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: chipone,icn8318 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + wake-gpios: + maxItems: 1 + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - wake-gpios + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@40 { + compatible = "chipone,icn8318"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_wake_pin_p66>; + wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt new file mode 100644 index 000000000..ca304357c --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt @@ -0,0 +1,34 @@ +* Toradex Colibri VF50 Touchscreen driver + +Required Properties: +- compatible must be toradex,vf50-touchscreen +- io-channels: adc channels being used by the Colibri VF50 module + IIO ADC for Y-, X-, Y+, X+ connections +- xp-gpios: FET gate driver for input of X+ +- xm-gpios: FET gate driver for input of X- +- yp-gpios: FET gate driver for input of Y+ +- ym-gpios: FET gate driver for input of Y- +- interrupts: pen irq interrupt for touch detection, signal from X plate +- pinctrl-names: "idle", "default" +- pinctrl-0: pinctrl node for pen/touch detection, pinctrl must provide + pull-up resistor on X+, X-. +- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux +- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values + +Example: + + touchctrl: vf50_touchctrl { + compatible = "toradex,vf50-touchscreen"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "idle","default"; + pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>; + pinctrl-1 = <&pinctrl_touchctrl_default>, <&pinctrl_touchctrl_gpios>; + vf50-ts-min-pressure = <200>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma140.yaml b/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma140.yaml new file mode 100644 index 000000000..3225c8d1f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma140.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/cypress,cy8ctma140.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cypress CY8CTMA140 series touchscreen controller bindings + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: cypress,cy8ctma140 + + reg: + const: 0x20 + + clock-frequency: + description: I2C client clock frequency, defined for host + minimum: 100000 + maximum: 400000 + + interrupts: + maxItems: 1 + + vcpin-supply: + description: Analog power supply regulator on VCPIN pin + + vdd-supply: + description: Digital power supply regulator on VDD pin + + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-swapped-x-y: true + touchscreen-max-pressure: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + - touchscreen-max-pressure + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@20 { + compatible = "cypress,cy8ctma140"; + reg = <0x20>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + touchscreen-max-pressure = <255>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&ab8500_ldo_aux2_reg>; + vcpin-supply = <&ab8500_ldo_aux2_reg>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma340.yaml b/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma340.yaml new file mode 100644 index 000000000..762e56ee9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma340.yaml @@ -0,0 +1,148 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/cypress,cy8ctma340.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cypress CY8CTMA340 series touchscreen controller bindings + +description: The Cypress CY8CTMA340 series (also known as "CYTTSP" after + the marketing name Cypress TrueTouch Standard Product) touchscreens can + be connected to either I2C or SPI buses. + +maintainers: + - Javier Martinez Canillas <javier@dowhile0.org> + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + oneOf: + - const: cypress,cy8ctma340 + - const: cypress,cy8ctst341 + - const: cypress,cyttsp-spi + description: Legacy compatible for SPI connected CY8CTMA340 + deprecated: true + - const: cypress,cyttsp-i2c + description: Legacy compatible for I2C connected CY8CTMA340 + deprecated: true + + reg: + description: I2C address when used on the I2C bus, or the SPI chip + select index when used on the SPI bus + + clock-frequency: + description: I2C client clock frequency, defined for host when using + the device on the I2C bus + minimum: 0 + maximum: 400000 + + spi-max-frequency: + description: SPI clock frequency, defined for host, defined when using + the device on the SPI bus. The throughput is maximum 2 Mbps so the + typical value is 2000000, if higher rates are used the total throughput + needs to be restricted to 2 Mbps. + minimum: 0 + maximum: 6000000 + + interrupts: + description: Interrupt to host + maxItems: 1 + + vcpin-supply: + description: Analog power supply regulator on VCPIN pin + + vdd-supply: + description: Digital power supply regulator on VDD pin + + reset-gpios: + description: Reset line for the touchscreen, should be tagged + as GPIO_ACTIVE_LOW + + bootloader-key: + description: the 8-byte bootloader key that is required to switch + the chip from bootloader mode (default mode) to application mode + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 8 + maxItems: 8 + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + + active-distance: + description: the distance in pixels beyond which a touch must move + before movement is detected and reported by the device + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + + active-interval-ms: + description: the minimum period in ms between consecutive + scanning/processing cycles when the chip is in active mode + minimum: 0 + maximum: 255 + + lowpower-interval-ms: + description: the minimum period in ms between consecutive + scanning/processing cycles when the chip is in low-power mode + minimum: 0 + maximum: 2550 + + touch-timeout-ms: + description: minimum time in ms spent in the active power state while no + touches are detected before entering low-power mode + minimum: 0 + maximum: 2550 + + use-handshake: + description: enable register-based handshake (boolean). This should only + be used if the chip is configured to use 'blocking communication with + timeout' (in this case the device generates an interrupt at the end of + every scanning/processing cycle) + $ref: /schemas/types.yaml#/definitions/flag + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - bootloader-key + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <1>; + cs-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + + touchscreen@0 { + compatible = "cypress,cy8ctma340"; + reg = <0>; + interrupt-parent = <&gpio>; + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + vdd-supply = <&ldo_aux1_reg>; + vcpin-supply = <&ldo_aux2_reg>; + bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + active-interval-ms = <0>; + touch-timeout-ms = <255>; + lowpower-interval-ms = <10>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml new file mode 100644 index 000000000..46bc8c028 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/edt-ft5x06.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: FocalTech EDT-FT5x06 Polytouch Bindings + +description: | + There are 5 variants of the chip for various touch panel sizes + FT5206GE1 2.8" .. 3.8" + FT5306DE4 4.3" .. 7" + FT5406EE8 7" .. 8.9" + FT5506EEG 7" .. 8.9" + FT5726NEI 5.7” .. 11.6" + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + - if: + properties: + compatible: + contains: + enum: + - evervision,ev-ft5726 + + then: + properties: + offset-x: true + offset-y: true + +properties: + compatible: + enum: + - edt,edt-ft5206 + - edt,edt-ft5306 + - edt,edt-ft5406 + - edt,edt-ft5506 + - evervision,ev-ft5726 + - focaltech,ft6236 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + wake-gpios: + maxItems: 1 + + wakeup-source: true + + vcc-supply: true + iovcc-supply: true + + gain: + description: Allows setting the sensitivity in the range from 0 to 31. + Note that lower values indicate higher sensitivity. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + + offset: + description: Allows setting the edge compensation in the range from 0 to 31. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + + offset-x: + description: Same as offset, but applies only to the horizontal position. + Range from 0 to 80, only supported by evervision,ev-ft5726 devices. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 80 + + offset-y: + description: Same as offset, but applies only to the vertical position. + Range from 0 to 80, only supported by evervision,ev-ft5726 devices. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 80 + + report-rate-hz: + description: | + Allows setting the scan rate in Hertz. + M06 supports range from 30 to 140 Hz. + M12 supports range from 1 to 255 Hz. + minimum: 1 + maximum: 255 + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + interrupt-controller: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + edt-ft5x06@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/eeti,exc3000.yaml b/Documentation/devicetree/bindings/input/touchscreen/eeti,exc3000.yaml new file mode 100644 index 000000000..007adbc89 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/eeti,exc3000.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/eeti,exc3000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: EETI EXC3000 series touchscreen controller + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - eeti,exc3000 + - eeti,exc80h60 + - eeti,exc80h84 + reg: + const: 0x2a + interrupts: + maxItems: 1 + reset-gpios: + maxItems: 1 + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + +additionalProperties: false + +examples: + - | + #include "dt-bindings/interrupt-controller/irq.h" + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@2a { + compatible = "eeti,exc3000"; + reg = <0x2a>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/eeti.txt b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt new file mode 100644 index 000000000..32b3712c9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt @@ -0,0 +1,30 @@ +Bindings for EETI touchscreen controller + +Required properties: +- compatible: should be "eeti,exc3000-i2c" +- reg: I2C address of the chip. Should be set to <0xa> +- interrupts: interrupt to which the chip is connected + +Optional properties: +- attn-gpios: A handle to a GPIO to check whether interrupt is still + latched. This is necessary for platforms that lack + support for level-triggered IRQs. + +The following optional properties described in touchscreen.txt are +also supported: + +- touchscreen-inverted-x +- touchscreen-inverted-y +- touchscreen-swapped-x-y + +Example: + +i2c-master { + touchscreen@a { + compatible = "eeti,exc3000-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio>; + interrupts = <123 IRQ_TYPE_EDGE_RISING>; + attn-gpios = <&gpio 123 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt new file mode 100644 index 000000000..92fb2620f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt @@ -0,0 +1,18 @@ +* EETI eGalax Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,egalax_ts" +- reg: i2c slave address +- interrupts: touch controller interrupt +- wakeup-gpios: the gpio pin to be used for waking up the controller + and also used as irq pin + +Example: + + touchscreen@4 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 2>; + wakeup-gpios = <&gpio1 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt new file mode 100644 index 000000000..c9f2c9f57 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt @@ -0,0 +1,25 @@ +* Elan eKTF2127 I2C touchscreen controller + +Required properties: + - compatible : "elan,ektf2127" or "elan,ektf2132" + - reg : I2C slave address of the chip (0x40) + - interrupts : interrupt specification for the ektf2127 interrupt + - power-gpios : GPIO specification for the pin connected to the + ektf2127's wake input. This needs to be driven high + to take ektf2127 out of its low power state + +For additional optional properties see: touchscreen.txt + +Example: + +i2c@00000000 { + ektf2127: touchscreen@15 { + compatible = "elan,ektf2127"; + reg = <0x15>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/elan,elants_i2c.yaml b/Documentation/devicetree/bindings/input/touchscreen/elan,elants_i2c.yaml new file mode 100644 index 000000000..f9053e5e9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/elan,elants_i2c.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/input/touchscreen/elan,elants_i2c.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Elantech I2C Touchscreen + +maintainers: + - David Heidelberg <david@ixit.cz> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + oneOf: + - enum: + - elan,ektf3624 + - elan,ekth3500 + - items: + - const: elan,ekth3915 + - const: elan,ekth3500 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + wakeup-source: + type: boolean + description: touchscreen can be used as a wakeup source. + + reset-gpios: + maxItems: 1 + description: reset gpio the chip is connected to. + + vcc33-supply: + description: a phandle for the regulator supplying 3.3V power. + + vccio-supply: + description: a phandle for the regulator supplying IO power. + + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + + interrupt-parent = <&gpio4>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt new file mode 100644 index 000000000..99d6f9d25 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -0,0 +1,34 @@ +Freescale mx25 TS conversion queue module + +mx25 touchscreen conversion queue module which controls the ADC unit of the +mx25 for attached touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tcq". + - reg: Memory range of the device. + - interrupts: Should be the interrupt number associated with this module within + the tscadc unit (<0>). + - fsl,wires: Should be '<4>' or '<5>' + +Optional properties: + - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. + - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value + between 1 and 4096. It is the ratio between the internal reference voltage + and the measured voltage after the plate was precharged. Resistance between + plates and therefore the voltage decreases with pressure so that a smaller + value is equivalent to a higher pressure. + - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before + the actual touch detection to wait for an even charge distribution in the + plate. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + interrupt-parent = <&tscadc>; + interrupts = <0>; + fsl,wires = <4>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml new file mode 100644 index 000000000..19ac9da42 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/goodix.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Goodix GT9xx series touchscreen controller Bindings + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - goodix,gt1151 + - goodix,gt1158 + - goodix,gt5663 + - goodix,gt5688 + - goodix,gt911 + - goodix,gt9110 + - goodix,gt912 + - goodix,gt9147 + - goodix,gt917s + - goodix,gt927 + - goodix,gt9271 + - goodix,gt928 + - goodix,gt9286 + - goodix,gt967 + + reg: + enum: [ 0x5d, 0x14 ] + + interrupts: + maxItems: 1 + + irq-gpios: + description: GPIO pin used for IRQ. The driver uses the interrupt gpio pin + as output to reset the device. + maxItems: 1 + + reset-gpios: + maxItems: 1 + + AVDD28-supply: + description: Analog power supply regulator on AVDD28 pin + + VDDIO-supply: + description: GPIO power supply regulator on VDDIO pin + + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + gt928@5d { + compatible = "goodix,gt928"; + reg = <0x5d>; + interrupt-parent = <&gpio>; + interrupts = <0 0>; + irq-gpios = <&gpio1 0 0>; + reset-gpios = <&gpio1 1 0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/hideep.txt b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt new file mode 100644 index 000000000..a47c36190 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/hideep.txt @@ -0,0 +1,41 @@ +* HiDeep Finger and Stylus touchscreen controller + +Required properties: +- compatible : must be "hideep,hideep-ts" +- reg : I2C slave address, (e.g. 0x6C). +- interrupts : Interrupt to which the chip is connected. + +Optional properties: +- vdd-supply : It is the controller supply for controlling + main voltage(3.3V) through the regulator. +- vid-supply : It is the controller supply for controlling + IO voltage(1.8V) through the regulator. +- reset-gpios : Define for reset gpio pin. + It is to use for reset IC. +- touchscreen-size-x : X axis size of touchscreen +- touchscreen-size-y : Y axis size of touchscreen +- linux,keycodes : Specifies an array of numeric keycode values to + be used for reporting button presses. The array can + contain up to 3 entries. + +Example: + +#include "dt-bindings/input/input.h" + +i2c@00000000 { + + /* ... */ + + touchscreen@6c { + compatible = "hideep,hideep-ts"; + reg = <0x6c>; + interrupt-parent = <&gpx1>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&ldo15_reg>; + vid-supply = <&ldo18_reg>; + reset-gpios = <&gpx1 5 0>; + touchscreen-size-x = <1080>; + touchscreen-size-y = <1920>; + linux,keycodes = <KEY_HOME>, <KEY_MENU>, <KEY_BACK>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml b/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml new file mode 100644 index 000000000..942562f1e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/hycon,hy46xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hycon HY46XX series touchscreen controller bindings + +description: | + There are 6 variants of the chip for various touch panel sizes and cover lens material + Glass: 0.3mm--4.0mm + PET/PMMA: 0.2mm--2.0mm + HY4613(B)-N048 < 6" + HY4614(B)-N068 7" .. 10.1" + HY4621-NS32 < 5" + HY4623-NS48 5.1" .. 7" + Glass: 0.3mm--8.0mm + PET/PMMA: 0.2mm--4.0mm + HY4633(B)-N048 < 6" + HY4635(B)-N048 < 7" .. 10.1" + +maintainers: + - Giulio Benetti <giulio.benetti@benettiengineering.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - hycon,hy4613 + - hycon,hy4614 + - hycon,hy4621 + - hycon,hy4623 + - hycon,hy4633 + - hycon,hy4635 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + vcc-supply: true + + hycon,threshold: + description: Allows setting the sensitivity in the range from 0 to 255. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + + hycon,glove-enable: + type: boolean + description: Allows enabling glove setting. + + hycon,report-speed-hz: + description: Allows setting the report speed in Hertz. + minimum: 1 + maximum: 255 + + hycon,noise-filter-enable: + type: boolean + description: Allows enabling power noise filter. + + hycon,filter-data: + description: Allows setting how many samples throw before reporting touch + in the range from 0 to 5. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 5 + + hycon,gain: + description: Allows setting the sensitivity distance in the range from 0 to 5. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 5 + + hycon,edge-offset: + description: Allows setting the edge compensation in the range from 0 to 16. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 16 + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + interrupt-controller: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@1c { + compatible = "hycon,hy4633"; + reg = <0x1c>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml b/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml new file mode 100644 index 000000000..9f7328999 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ilitek_ts_i2c.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/ilitek_ts_i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ilitek I2C Touchscreen Controller + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - ilitek,ili210x + - ilitek,ili2117 + - ilitek,ili2120 + - ilitek,ili2130 + - ilitek,ili2131 + - ilitek,ili2132 + - ilitek,ili2316 + - ilitek,ili2322 + - ilitek,ili2323 + - ilitek,ili2326 + - ilitek,ili251x + - ilitek,ili2520 + - ilitek,ili2521 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + wakeup-source: + type: boolean + description: touchscreen can be used as a wakeup source. + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@41 { + compatible = "ilitek,ili2520"; + reg = <0x41>; + + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + touchscreen-inverted-y; + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/imagis,ist3038c.yaml b/Documentation/devicetree/bindings/input/touchscreen/imagis,ist3038c.yaml new file mode 100644 index 000000000..e3a2b871e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/imagis,ist3038c.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/imagis,ist3038c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Imagis IST30XXC family touchscreen controller bindings + +maintainers: + - Markuss Broks <markuss.broks@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + $nodename: + pattern: "^touchscreen@[0-9a-f]+$" + + compatible: + enum: + - imagis,ist3038c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: + description: Power supply regulator for the chip + + vddio-supply: + description: Power supply regulator for the I2C bus + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@50 { + compatible = "imagis,ist3038c"; + reg = <0x50>; + interrupt-parent = <&gpio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&ldo1_reg>; + vddio-supply = <&ldo2_reg>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; + touchscreen-fuzz-x = <10>; + touchscreen-fuzz-y = <10>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt new file mode 100644 index 000000000..164915004 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -0,0 +1,38 @@ +* Freescale i.MX6UL Touch Controller + +Required properties: +- compatible: must be "fsl,imx6ul-tsc". +- reg: this touch controller address and the ADC2 address. +- interrupts: the interrupt of this touch controller and ADC2. +- clocks: the root clock of touch controller and ADC2. +- clock-names; must be "tsc" and "adc". +- xnur-gpio: the X- gpio this controller connect to. + This xnur-gpio returns to low once the finger leave the touch screen (The + last touch event the touch controller capture). + +Optional properties: +- measure-delay-time: the value of measure delay time. + Before X-axis or Y-axis measurement, the screen need some time before + even potential distribution ready. + This value depends on the touch screen. +- pre-charge-time: the touch screen need some time to precharge. + This value depends on the touch screen. +- touchscreen-average-samples: Number of data samples which are averaged for + each read. Valid values are 1, 4, 8, 16 and 32. + +Example: + tsc: tsc@2040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xfff>; + pre-charge-time = <0xffff>; + touchscreen-average-samples = <32>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt new file mode 100644 index 000000000..41cbf4b7a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC Touchscreen Controller (TSC) + +Required properties: +- compatible: must be "nxp,lpc3220-tsc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The TSC/ADC interrupt + +Example: + + tsc@40048000 { + compatible = "nxp,lpc3220-tsc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt new file mode 100644 index 000000000..05e982c34 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/max11801-ts.txt @@ -0,0 +1,17 @@ +* MAXI MAX11801 Resistive touch screen controller with i2c interface + +Required properties: +- compatible: must be "maxim,max11801" +- reg: i2c slave address +- interrupts: touch controller interrupt + +Example: + +&i2c1 { + max11801: touchscreen@48 { + compatible = "maxim,max11801"; + reg = <0x48>; + interrupt-parent = <&gpio3>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml b/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml new file mode 100644 index 000000000..62366886f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/melfas,mms114.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/melfas,mms114.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Melfas MMS114 family touchscreen controller bindings + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + items: + - enum: + - melfas,mms114 + - melfas,mms134s + - melfas,mms136 + - melfas,mms152 + - melfas,mms345l + + reg: + description: I2C address + + clock-frequency: + description: I2C client clock frequency, defined for host + minimum: 100000 + maximum: 400000 + + interrupts: + maxItems: 1 + + avdd-supply: + description: Analog power supply regulator on AVDD pin + + vdd-supply: + description: Digital power supply regulator on VDD pin + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-fuzz-pressure: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + touchscreen-max-pressure: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <39 IRQ_TYPE_EDGE_FALLING>; + avdd-supply = <&ldo1_reg>; + vdd-supply = <&ldo2_reg>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; + touchscreen-fuzz-x = <10>; + touchscreen-fuzz-y = <10>; + touchscreen-fuzz-pressure = <10>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt new file mode 100644 index 000000000..b2ab5498e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt @@ -0,0 +1,20 @@ +* MELFAS MIP4 Touchscreen + +Required properties: +- compatible: must be "melfas,mip4_ts" +- reg: I2C slave address of the chip (0x48 or 0x34) +- interrupts: interrupt to which the chip is connected + +Optional properties: +- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip + +Example: + i2c@00000000 { + touchscreen: melfas_mip4@48 { + compatible = "melfas,mip4_ts"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml b/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml new file mode 100644 index 000000000..3a42c23fa --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mstar,msg2638.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/mstar,msg2638.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MStar msg2638 touchscreen controller Bindings + +maintainers: + - Vincent Knecht <vincent.knecht@mailoo.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: mstar,msg2638 + + reg: + const: 0x26 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + vdd-supply: + description: Power supply regulator for the chip + + vddio-supply: + description: Power supply regulator for the I2C bus + + touchscreen-size-x: true + touchscreen-size-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - reset-gpios + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@26 { + compatible = "mstar,msg2638"; + reg = <0x26>; + interrupt-parent = <&msmgpio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&msmgpio 100 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_reset_default>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + touchscreen-size-x = <2048>; + touchscreen-size-y = <2048>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir,pixcir_ts.yaml b/Documentation/devicetree/bindings/input/touchscreen/pixcir,pixcir_ts.yaml new file mode 100644 index 000000000..f9998edbf --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir,pixcir_ts.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/pixcir,pixcir_ts.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Pixcir Touchscreen Controller Device Tree Bindings + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - pixcir,pixcir_ts + - pixcir,pixcir_tangoc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + attb-gpio: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + enable-gpios: + maxItems: 1 + + wake-gpios: + maxItems: 1 + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - attb-gpio + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/raspberrypi,firmware-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/raspberrypi,firmware-ts.txt new file mode 100644 index 000000000..2a1af240c --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/raspberrypi,firmware-ts.txt @@ -0,0 +1,26 @@ +Raspberry Pi firmware based 7" touchscreen +===================================== + +Required properties: + - compatible: "raspberrypi,firmware-ts" + +Optional properties: + - firmware: Reference to RPi's firmware device node + - touchscreen-size-x: See touchscreen.txt + - touchscreen-size-y: See touchscreen.txt + - touchscreen-inverted-x: See touchscreen.txt + - touchscreen-inverted-y: See touchscreen.txt + - touchscreen-swapped-x-y: See touchscreen.txt + +Example: + +firmware: firmware-rpi { + compatible = "raspberrypi,bcm2835-firmware"; + mboxes = <&mailbox>; + + ts: touchscreen { + compatible = "raspberrypi,firmware-ts"; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.yaml b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.yaml new file mode 100644 index 000000000..7fc22a403 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/resistive-adc-touch.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/resistive-adc-touch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic resistive touchscreen ADC + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +description: | + Generic ADC based resistive touchscreen controller + The device must be connected to an ADC device that provides channels for + position measurement and optional pressure. + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: resistive-adc-touch + + io-channels: + minItems: 2 + items: + - description: x + - description: y + - description: pressure (optional) + - description: z1 (optional) + - description: z2 (optional) + + io-channel-names: + oneOf: + - items: + - enum: [x, y] + - enum: [x, y] + - items: + - enum: [x, y, pressure] + - enum: [x, y, pressure] + - enum: [x, y, pressure] + - items: + - enum: [x, y, z1, z2] + - enum: [x, y, z1, z2] + - enum: [x, y, z1, z2] + - enum: [x, y, z1, z2] + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + touchscreen-min-pressure: true + touchscreen-x-plate-ohms: true + +additionalProperties: false + +required: + - compatible + - io-channels + - io-channel-names + +examples: + - | + touchscreen { + compatible = "resistive-adc-touch"; + io-channels = <&adc 24>, <&adc 25>; + io-channel-names = "y", "x"; + }; + - | + touchscreen { + compatible = "resistive-adc-touch"; + touchscreen-min-pressure = <50000>; + io-channels = <&adc 24>, <&adc 25>, <&adc 26>; + io-channel-names = "y", "pressure", "x"; + }; + - | + touchscreen { + compatible = "resistive-adc-touch"; + touchscreen-min-pressure = <50000>; + io-channels = <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>; + io-channel-names = "x", "z1", "z2", "y"; + touchscreen-x-plate-ohms = <800>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt new file mode 100644 index 000000000..6805d10d2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/samsung,s6sy761.txt @@ -0,0 +1,32 @@ +* Samsung S6SY761 touchscreen controller + +Required properties: +- compatible : must be "samsung,s6sy761" +- reg : I2C slave address, (e.g. 0x48) +- interrupts : interrupt specification +- avdd-supply : analogic power supply +- vdd-supply : power supply + +Optional properties: +- touchscreen-size-x : see touchscreen.txt. This property is embedded in the + device. If defined it forces a different x resolution. +- touchscreen-size-y : see touchscreen.txt. This property is embedded in the + device. If defined it forces a different y resolution. + +Example: + +i2c@00000000 { + + /* ... */ + + touchscreen@48 { + compatible = "samsung,s6sy761"; + reg = <0x48>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_NONE>; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead,gsl1680.yaml b/Documentation/devicetree/bindings/input/touchscreen/silead,gsl1680.yaml new file mode 100644 index 000000000..eec6f7f6f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/silead,gsl1680.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/silead,gsl1680.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silead GSL1680 Touchscreen Controller Device Tree Bindings + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - silead,gsl1680 + - silead,gsl1688 + - silead,gsl3670 + - silead,gsl3675 + - silead,gsl3692 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + power-gpios: + maxItems: 1 + + firmware-name: + $ref: /schemas/types.yaml#/definitions/string + description: > + File basename for board specific firmware + + silead,max-fingers: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 5 + description: > + Maximum number of fingers the touchscreen can detect + + silead,home-button: + type: boolean + description: > + Does the device have a capacitive home-button build into the + touchscreen? + + avdd-supply: + description: > + Regulator phandle for controller AVDD + + vddio-supply: + description: > + Regulator phandle for controller VDDIO + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - power-gpios + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@40 { + compatible = "silead,gsl1680"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + silead,max-fingers = <5>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt new file mode 100644 index 000000000..8f5322e01 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt @@ -0,0 +1,31 @@ +* SiS I2C Multiple Touch Controller + +Required properties: +- compatible: must be "sis,9200-ts" +- reg: i2c slave address +- interrupts: touch controller interrupt (see interrupt + binding [0]) + +Optional properties: +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the + device (see pinctrl binding [1]). +- attn-gpios: the gpio pin used as attention line +- reset-gpios: the gpio pin used to reset the controller +- wakeup-source: touchscreen can be used as a wakeup source + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + + sis9255@5c { + compatible = "sis,9200-ts"; + reg = <0x5c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sis>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; + irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix,st1232.yaml b/Documentation/devicetree/bindings/input/touchscreen/sitronix,st1232.yaml new file mode 100644 index 000000000..1d8ca19fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix,st1232.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/sitronix,st1232.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sitronix st1232 or st1633 touchscreen controller + +maintainers: + - Bastian Hecht <hechtb@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - sitronix,st1232 + - sitronix,st1633 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + gpios: + description: A phandle to the reset GPIO + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupts = <2 0>; + gpios = <&gpio1 166 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt new file mode 100644 index 000000000..0a5d0cb4a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/st,stmfts.txt @@ -0,0 +1,41 @@ +* ST-Microelectronics FingerTip touchscreen controller + +The ST-Microelectronics FingerTip device provides a basic touchscreen +functionality. Along with it the user can enable the touchkey which can work as +a basic HOME and BACK key for phones. + +The driver supports also hovering as an absolute single touch event with x, y, z +coordinates. + +Required properties: +- compatible : must be "st,stmfts" +- reg : I2C slave address, (e.g. 0x49) +- interrupts : interrupt specification +- avdd-supply : analogic power supply +- vdd-supply : power supply +- touchscreen-size-x : see touchscreen.txt +- touchscreen-size-y : see touchscreen.txt + +Optional properties: +- touch-key-connected : specifies whether the touchkey feature is connected +- ledvdd-supply : power supply to the touch key leds + +Example: + +i2c@00000000 { + + /* ... */ + + touchscreen@49 { + compatible = "st,stmfts"; + reg = <0x49>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_NONE>; + touchscreen-size-x = <1599>; + touchscreen-size-y = <2559>; + touch-key-connected; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + ledvdd-supply = <&ldo33_reg>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 000000000..238b51555 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,108 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us + 1 -> 50 us + 2 -> 100 us + 3 -> 500 us + 4 -> 1 ms + 5 -> 5 ms + 6 -> 10 ms + 7 -> 50 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us + 1 -> 100 us + 2 -> 500 us + 3 -> 1 ms + 4 -> 5 ms + 5 -> 10 ms + 6 -> 50 ms + 7 -> 100 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) + +Optional properties common with MFD (deprecated): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks + 1 -> 44 clocks + 2 -> 56 clocks + 3 -> 64 clocks + 4 -> 80 clocks (recommended) + 5 -> 96 clocks + 6 -> 124 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC + 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal + 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz + 1 -> 3.25 MHz + 2 || 3 -> 6.5 MHz + +Node should be child node of stmpe node to which it belongs. + +Note that common ADC settings of stmpe_touchscreen (child) will take precedence +over the settings done in MFD. + +Example: + +stmpe811@41 { + compatible = "st,stmpe811"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touch_int>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio4>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + /* Common ADC settings */ + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + /* ADC converstion time: 80 clocks */ + st,sample-time = <4>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + reg = <0>; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + }; + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt new file mode 100644 index 000000000..0ebe6dd04 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt @@ -0,0 +1,23 @@ +* Semtech SX8654 I2C Touchscreen Controller + +Required properties: +- compatible: must be one of the following, depending on the model: + "semtech,sx8650" + "semtech,sx8654" + "semtech,sx8655" + "semtech,sx8656" +- reg: i2c slave address +- interrupts: touch controller interrupt + +Optional properties: + - reset-gpios: GPIO specification for the NRST input + +Example: + + sx8654@48 { + compatible = "semtech,sx8654"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti,am3359-tsc.yaml b/Documentation/devicetree/bindings/input/touchscreen/ti,am3359-tsc.yaml new file mode 100644 index 000000000..e44cc65ab --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti,am3359-tsc.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/ti,am3359-tsc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI AM3359 Touchscreen controller + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + const: ti,am3359-tsc + + ti,wires: + description: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [4, 5, 8] + + ti,x-plate-resistance: + description: X plate resistance + $ref: /schemas/types.yaml#/definitions/uint32 + + ti,coordinate-readouts: + description: The sequencer supports a total of 16 programmable steps. Each + step is used to read a single coordinate. A single readout is enough but + multiple reads can increase the quality. A value of 5 means, 5 reads for + X, 5 for Y and 2 for Z (always). This utilises 12 of the 16 software steps + available. The remaining 4 can be used by the ADC. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 6 + + ti,wire-config: + description: Different boards could have a different order for connecting + wires on touchscreen. We need to provide an 8-bit number where the + first four bits represent the analog lines and the next 4 bits represent + positive/negative terminal on that input line. Notations to represent the + input lines and terminals respectively are as follows, AIN0 = 0, AIN1 = 1 + and so on until AIN7 = 7. XP = 0, XN = 1, YP = 2, YN = 3. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 4 + maxItems: 8 + + ti,charge-delay: + description: Length of touch screen charge delay step in terms of ADC clock + cycles. Charge delay value should be large in order to avoid false pen-up + events. This value effects the overall sampling speed, hence need to be + kept as low as possible, while avoiding false pen-up event. Start from a + lower value, say 0x400, and increase value until false pen-up events are + avoided. The pen-up detection happens immediately after the charge step, + so this does in fact function as a hardware knob for adjusting the amount + of "settling time". + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - compatible + - ti,wires + - ti,x-plate-resistance + - ti,coordinate-readouts + - ti,wire-config + +additionalProperties: false + +examples: + - | + tsc { + compatible = "ti,am3359-tsc"; + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + ti,charge-delay = <0x400>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml b/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml new file mode 100644 index 000000000..938aab016 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti,tsc2005.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/ti,tsc2005.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TSC2004 and TSC2005 touchscreen controller bindings + +maintainers: + - Marek Vasut <marex@denx.de> + - Michael Welling <mwelling@ieee.org> + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + enum: + - ti,tsc2004 + - ti,tsc2005 + + reg: + maxItems: 1 + description: | + I2C address when used on the I2C bus, or the SPI chip select index + when used on the SPI bus + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: GPIO specifier for the controller reset line + + spi-max-frequency: + description: TSC2005 SPI bus clock frequency. + maximum: 25000000 + + ti,x-plate-ohms: + description: resistance of the touchscreen's X plates in ohm (defaults to 280) + + ti,esd-recovery-timeout-ms: + description: | + if the touchscreen does not respond after the configured time + (in milli seconds), the driver will reset it. This is disabled + by default. + + vio-supply: + description: Regulator specifier + + touchscreen-fuzz-pressure: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-max-pressure: true + touchscreen-size-x: true + touchscreen-size-y: true + +allOf: + - $ref: touchscreen.yaml# + - if: + properties: + compatible: + contains: + const: ti,tsc2004 + then: + properties: + spi-max-frequency: false + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt new file mode 100644 index 000000000..e1adb902d --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -0,0 +1 @@ +See touchscreen.yaml diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml new file mode 100644 index 000000000..4b5b212c7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/touchscreen.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common touchscreen Bindings + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +properties: + touchscreen-min-x: + description: minimum x coordinate reported + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + touchscreen-min-y: + description: minimum y coordinate reported + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + touchscreen-size-x: + description: horizontal resolution of touchscreen (maximum x coordinate reported + 1) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-size-y: + description: vertical resolution of touchscreen (maximum y coordinate reported + 1) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-max-pressure: + description: maximum reported pressure (arbitrary range dependent on the controller) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-min-pressure: + description: minimum pressure on the touchscreen to be achieved in order + for the touchscreen driver to report a touch event. + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-fuzz-x: + description: horizontal noise value of the absolute input device (in pixels) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-fuzz-y: + description: vertical noise value of the absolute input device (in pixels) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-fuzz-pressure: + description: pressure noise value of the absolute input device (arbitrary + range dependent on the controller) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-average-samples: + description: Number of data samples which are averaged for each read (valid + values dependent on the controller) + $ref: /schemas/types.yaml#/definitions/uint32 + + touchscreen-inverted-x: + description: X axis is inverted + type: boolean + + touchscreen-inverted-y: + description: Y axis is inverted + type: boolean + + touchscreen-swapped-x-y: + description: X and Y axis are swapped + Swapping is done after inverting the axis + type: boolean + + touchscreen-x-mm: + description: horizontal length in mm of the touchscreen + + touchscreen-y-mm: + description: vertical length in mm of the touchscreen + + touchscreen-x-plate-ohms: + description: Resistance of the X-plate in Ohms + + touchscreen-y-plate-ohms: + description: Resistance of the Y-plate in Ohms + +dependencies: + touchscreen-size-x: [ touchscreen-size-y ] + touchscreen-size-y: [ touchscreen-size-x ] + touchscreen-x-mm: [ touchscreen-y-mm ] + touchscreen-y-mm: [ touchscreen-x-mm ] + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt new file mode 100644 index 000000000..4c1c092c2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt @@ -0,0 +1,11 @@ +* TS-4800 Touchscreen bindings + +Required properties: +- compatible: must be "technologic,ts4800-ts" +- reg: physical base address of the controller and length of memory mapped + region. +- syscon: phandle / integers array that points to the syscon node which + describes the FPGA's syscon registers. + - phandle to FPGA's syscon + - offset to the touchscreen register + - offset to the touchscreen enable bit diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt new file mode 100644 index 000000000..ed00f61b8 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt @@ -0,0 +1,39 @@ +* Texas Instruments tsc2007 touchscreen controller + +Required properties: +- compatible: must be "ti,tsc2007". +- reg: I2C address of the chip. +- ti,x-plate-ohms: X-plate resistance in ohms. + +Optional properties: +- gpios: the interrupt gpio the chip is connected to (trough the penirq pin). + The penirq pin goes to low when the panel is touched. + (see GPIO binding[1] for more details). +- interrupts: (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). +- ti,max-rt: maximum pressure. +- ti,fuzzx: specifies the absolute input fuzz x value. + If set, it will permit noise in the data up to +- the value given to the fuzz + parameter, that is used to filter noise from the event stream. +- ti,fuzzy: specifies the absolute input fuzz y value. +- ti,fuzzz: specifies the absolute input fuzz z value. +- ti,poll-period: how much time to wait (in milliseconds) before reading again the + values from the tsc2007. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + tsc2007@49 { + compatible = "ti,tsc2007"; + reg = <0x49>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 0x8>; + gpios = <&gpio4 0 0>; + ti,x-plate-ohms = <180>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt new file mode 100644 index 000000000..27d55a506 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zet6223.txt @@ -0,0 +1,30 @@ +Zeitec ZET6223 I2C touchscreen controller + +Required properties: +- compatible : "zeitec,zet6223" +- reg : I2C slave address of the chip (0x76) +- interrupts : interrupt specification for the zet6223 interrupt + +Optional properties: + +- vio-supply : Specification for VIO supply (1.8V or 3.3V, + depending on system interface needs). +- vcc-supply : Specification for 3.3V VCC supply. +- touchscreen-size-x : See touchscreen.txt +- touchscreen-size-y : See touchscreen.txt +- touchscreen-inverted-x : See touchscreen.txt +- touchscreen-inverted-y : See touchscreen.txt +- touchscreen-swapped-x-y : See touchscreen.txt + +Example: + +i2c@00000000 { + + zet6223: touchscreen@76 { + compatible = "zeitec,zet6223"; + reg = <0x76>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING> + }; + +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt new file mode 100644 index 000000000..e3c27c4fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -0,0 +1,34 @@ +* Neonode infrared touchscreen controller + +Required properties: +- compatible: must be "neonode,zforce" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- reset-gpios: reset gpio the chip is connected to +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- irq-gpios : interrupt gpio the chip is connected to +- vdd-supply: Regulator controlling the controller supply + +Example: + + i2c@00000000 { + /* ... */ + + zforce_ts@50 { + compatible = "neonode,zforce"; + reg = <0x50>; + interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; + + reset-gpios = <&gpio5 9 0>; /* RST */ + irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml b/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml new file mode 100644 index 000000000..b4e5ba7c0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zinitix,bt400.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/zinitix,bt400.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Zinitix BT4xx and BT5xx series touchscreen controller bindings + +description: The Zinitix BT4xx and BT5xx series of touchscreen controllers + are Korea-produced touchscreens with embedded microcontrollers. The + BT4xx series was produced 2010-2013 and the BT5xx series 2013-2014. + +maintainers: + - Michael Srba <Michael.Srba@seznam.cz> + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + enum: + - zinitix,bt402 + - zinitix,bt403 + - zinitix,bt404 + - zinitix,bt412 + - zinitix,bt413 + - zinitix,bt431 + - zinitix,bt432 + - zinitix,bt531 + - zinitix,bt532 + - zinitix,bt538 + - zinitix,bt541 + - zinitix,bt548 + - zinitix,bt554 + - zinitix,at100 + + reg: + description: I2C address on the I2C bus + + clock-frequency: + description: I2C client clock frequency, defined for host when using + the device on the I2C bus + minimum: 0 + maximum: 400000 + + interrupts: + description: Interrupt to host + maxItems: 1 + + vcca-supply: + description: Analog power supply regulator on the VCCA pin + + vdd-supply: + description: Digital power supply regulator on the VDD pin. + In older device trees this can be the accidental name for the analog + supply on the VCCA pin, and in that case the deprecated vddo-supply is + used for the digital power supply. + + vddo-supply: + description: Deprecated name for the digital power supply, use vdd-supply + as this reflects the real name of the pin. If this supply is present, + the vdd-supply represents VCCA instead of VDD. Implementers should first + check for this property, and if it is present assume that the vdd-supply + represents the analog supply. + deprecated: true + + reset-gpios: + description: Reset line for the touchscreen, should be tagged + as GPIO_ACTIVE_LOW + + zinitix,mode: + description: Mode of reporting touch points. Some modes may not work + with a particular ts firmware for unknown reasons. Available modes are + 1 and 2. Mode 2 is the default and preferred. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2] + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@20 { + compatible = "zinitix,bt541"; + reg = <0x20>; + interrupt-parent = <&gpio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + vcca-supply = <®_vcca_tsp>; + vdd-supply = <®_vdd_tsp>; + touchscreen-size-x = <540>; + touchscreen-size-y = <960>; + zinitix,mode = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt new file mode 100644 index 000000000..8682ab6d4 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -0,0 +1,30 @@ +Texas Instruments TPS65217 and TPS65218 power button + +This module is part of the TPS65217/TPS65218. For more details about the whole +TPS65217 chip see Documentation/devicetree/bindings/regulator/tps65217.txt. + +This driver provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton" + +Required properties: +- interrupts: should be one of the following + - <2>: For controllers compatible with tps65217 + - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 + +Examples: + +&tps { + tps65217-pwrbutton { + compatible = "ti,tps65217-pwrbutton"; + interrupts = <2>; + }; +}; + +&tps { + power-button { + compatible = "ti,tps65218-pwrbutton"; + interrupts = <3 IRQ_TYPE_EDGE_BOTH>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/twl4030-keypad.txt b/Documentation/devicetree/bindings/input/twl4030-keypad.txt new file mode 100644 index 000000000..e4be2f76a --- /dev/null +++ b/Documentation/devicetree/bindings/input/twl4030-keypad.txt @@ -0,0 +1,27 @@ +* TWL4030's Keypad Controller device tree bindings + +TWL4030's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + + * keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,twl4030-keypad": For controllers compatible with twl4030 keypad + controller. +- interrupt: should be one of the following + - <1>: For controllers compatible with twl4030 keypad controller. + +Example: + twl_keypad: keypad { + compatible = "ti,twl4030-keypad"; + interrupts = <1>; + keypad,num-rows = <8>; + keypad,num-columns = <8>; + }; diff --git a/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt b/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt new file mode 100644 index 000000000..f5021214e --- /dev/null +++ b/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt @@ -0,0 +1,21 @@ +Texas Instruments TWL family (twl4030) pwrbutton module + +This module is part of the TWL4030. For more details about the whole +chip see Documentation/devicetree/bindings/mfd/twl-family.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,twl4030-pwrbutton": For controllers compatible with twl4030 +- interrupts: should be one of the following + - <8>: For controllers compatible with twl4030 + +Example: + +&twl { + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt b/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt new file mode 100644 index 000000000..43ef770df --- /dev/null +++ b/Documentation/devicetree/bindings/input/zii,rave-sp-pwrbutton.txt @@ -0,0 +1,22 @@ +Zodiac Inflight Innovations RAVE Supervisory Processor Power Button Bindings + +RAVE SP input device is a "MFD cell" device corresponding to power +button functionality of RAVE Supervisory Processor. It is expected +that its Device Tree node is specified as a child of the node +corresponding to the parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-pwrbutton" + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + pwrbutton { + compatible = "zii,rave-sp-pwrbutton"; + }; + } |