diff options
Diffstat (limited to 'Documentation/devicetree/bindings/leds/leds-bcm6328.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/leds/leds-bcm6328.yaml | 404 |
1 files changed, 404 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml b/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml new file mode 100644 index 000000000..51cc0d82c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.yaml @@ -0,0 +1,404 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/leds-bcm6328.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LEDs connected to Broadcom BCM6328 controller + +maintainers: + - Álvaro Fernández Rojas <noltari@gmail.com> + +description: | + This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268. + In these SoCs it's possible to control LEDs both as GPIOs or by hardware. + However, on some devices there are Serial LEDs (LEDs connected to a 74x164 + controller), which can either be controlled by software (exporting the 74x164 + as spi-gpio. See + Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml), or by hardware + using this driver. + Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and + exporting the 74x164 as spi-gpio prevents those LEDs to be hardware + controlled, so the only chance to keep them working is by using this driver. + + BCM6328 LED controller has a HWDIS register, which controls whether a LED + should be controlled by a hardware signal instead of the MODE register value, + with 0 meaning hardware control enabled and 1 hardware control disabled. This + is usually 1:1 for hardware to LED signals, but through the activity/link + registers you have some limited control over rerouting the LEDs (as + explained later in brcm,link-signal-sources). Even if a LED is hardware + controlled you are still able to make it blink or light it up if it isn't, + but you can't turn it off if the hardware decides to light it up. For this + reason, hardware controlled LEDs aren't registered as LED class devices. + + Each LED is represented as a sub-node of the brcm,bcm6328-leds device. + +properties: + compatible: + const: brcm,bcm6328-leds + + reg: + maxItems: 1 + + brcm,serial-leds: + type: boolean + description: Enables Serial LEDs. + + brcm,serial-mux: + type: boolean + description: Enables Serial LEDs multiplexing. + + brcm,serial-clk-low: + type: boolean + description: Makes clock signal active low. + + brcm,serial-dat-low: + type: boolean + description: Makes data signal active low. + + brcm,serial-shift-inv: + type: boolean + description: Inverts Serial LEDs shift direction. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "@[a-f0-9]+$": + type: object + + $ref: common.yaml# + + properties: + reg: + items: + - maximum: 23 + description: LED pin number (only LEDs 0 to 23 are valid). + + active-low: + type: boolean + description: Makes LED active low. + + brcm,hardware-controlled: + type: boolean + description: Makes this LED hardware controlled. + + brcm,link-signal-sources: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + description: > + An array of hardware link signal sources. Up to four link hardware + signals can get muxed into these LEDs. Only valid for LEDs 0 to 7, + where LED signals 0 to 3 may be muxed to LEDs 0 to 3, and signals 4 to + 7 may be muxed to LEDs 4 to 7. A signal can be muxed to more than one + LED, and one LED can have more than one source signal. + + brcm,activity-signal-sources: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + description: > + An array of hardware activity signal sources. Up to four activity + hardware signals can get muxed into these LEDs. Only valid for LEDs 0 + to 7, where LED signals 0 to 3 may be muxed to LEDs 0 to 3, and + signals 4 to 7 may be muxed to LEDs 4 to 7. A signal can be muxed to + more than one LED, and one LED can have more than one source signal. + + required: + - reg + + unevaluatedProperties: false + +required: + - reg + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + /* BCM6328 with 4 EPHY LEDs */ + led-controller@10000800 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000800 0x24>; + + alarm_red@2 { + reg = <2>; + active-low; + label = "red:alarm"; + }; + + inet_green@3 { + reg = <3>; + active-low; + label = "green:inet"; + }; + + power_green@4 { + reg = <4>; + active-low; + label = "green:power"; + default-state = "on"; + }; + + ephy0_spd@17 { + reg = <17>; + brcm,hardware-controlled; + }; + + ephy1_spd@18 { + reg = <18>; + brcm,hardware-controlled; + }; + + ephy2_spd@19 { + reg = <19>; + brcm,hardware-controlled; + }; + + ephy3_spd@20 { + reg = <20>; + brcm,hardware-controlled; + }; + }; + - | + /* BCM63268 with Serial/GPHY0 LEDs */ + led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + brcm,serial-leds; + brcm,serial-dat-low; + brcm,serial-shift-inv; + + gphy0_spd0@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + }; + + gphy0_spd1@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,link-signal-sources = <1>; + }; + + inet_red@2 { + reg = <2>; + active-low; + label = "red:inet"; + }; + + dsl_green@3 { + reg = <3>; + active-low; + label = "green:dsl"; + }; + + usb_green@4 { + reg = <4>; + active-low; + label = "green:usb"; + }; + + wps_green@7 { + reg = <7>; + active-low; + label = "green:wps"; + }; + + inet_green@8 { + reg = <8>; + active-low; + label = "green:inet"; + }; + + ephy0_act@9 { + reg = <9>; + brcm,hardware-controlled; + }; + + ephy1_act@10 { + reg = <10>; + brcm,hardware-controlled; + }; + + ephy2_act@11 { + reg = <11>; + brcm,hardware-controlled; + }; + + gphy0_act@12 { + reg = <12>; + brcm,hardware-controlled; + }; + + ephy0_spd@13 { + reg = <13>; + brcm,hardware-controlled; + }; + + ephy1_spd@14 { + reg = <14>; + brcm,hardware-controlled; + }; + + ephy2_spd@15 { + reg = <15>; + brcm,hardware-controlled; + }; + + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + - | + /* BCM6362 with 1 LED for each EPHY */ + led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0>; + /* USB link/activity routed to USB LED */ + }; + + inet@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,activity-signal-sources = <1>; + /* INET activity routed to INET LED */ + }; + + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY0 LED */ + }; + + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY1 LED */ + }; + + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY2 LED */ + }; + + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY3 LED */ + }; + + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + - | + /* BCM6362 with 1 LED for all EPHYs */ + led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0 1>; + brcm,activity-signal-sources = <0 1>; + /* USB/INET link/activity routed to USB LED */ + }; + + ephy@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4 5 6 7>; + /* EPHY0/1/2/3 link routed to EPHY0 LED */ + }; + + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; + - | + /* BCM6362 with EPHY LEDs swapped */ + led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0 1>; + /* USB link/act and INET act routed to USB LED */ + }; + + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY0 LED */ + }; + + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY1 LED */ + }; + + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY2 LED */ + }; + + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY3 LED */ + }; + + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; + }; |