diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt | 70 |
1 files changed, 70 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt new file mode 100644 index 000000000..c3a75ac6e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -0,0 +1,70 @@ +Amlogic Meson AXG DWC PCIE SoC controller + +Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and +inherits common properties defined in +Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml. + +Additional properties are described here: + +Required properties: +- compatible: + should contain : + - "amlogic,axg-pcie" for AXG SoC Family + - "amlogic,g12a-pcie" for G12A SoC Family + to identify the core. +- reg: + should contain the configuration address space. +- reg-names: Must be + - "elbi" External local bus interface registers + - "cfg" Meson specific registers + - "config" PCIe configuration space +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must include the following entries: + - "pclk" PCIe GEN 100M PLL clock + - "port" PCIe_x(A or B) RC clock gate + - "general" PCIe Phy clock +- resets: phandle to the reset lines. +- reset-names: must contain "port" and "apb" + - "port" Port A or B reset + - "apb" Share APB reset +- phys: should contain a phandle to the PCIE phy +- phy-names: must contain "pcie" + +- device_type: + should be "pci". As specified in snps,dw-pcie.yaml + + +Example configuration: + + pcie: pcie@f9800000 { + compatible = "amlogic,axg-pcie", "snps,dw-pcie"; + reg = <0x0 0xf9800000 0x0 0x400000 + 0x0 0xff646000 0x0 0x2000 + 0x0 0xf9f00000 0x0 0x100000>; + reg-names = "elbi", "cfg", "config"; + reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; + bus-range = <0x0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>; + + clocks = <&clkc CLKID_USB + &clkc CLKID_PCIE_A + &clkc CLKID_PCIE_CML_EN0>; + clock-names = "general", + "pclk", + "port"; + resets = <&reset RESET_PCIE_A>, + <&reset RESET_PCIE_APB>; + reset-names = "port", + "apb"; + phys = <&pcie_phy>; + phy-names = "pcie"; + }; |