diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml | 373 |
1 files changed, 373 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml new file mode 100644 index 000000000..d61585c96 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml @@ -0,0 +1,373 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra20-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra USB PHY + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - nvidia,tegra124-usb-phy + - nvidia,tegra114-usb-phy + - enum: + - nvidia,tegra30-usb-phy + - items: + - enum: + - nvidia,tegra30-usb-phy + - nvidia,tegra20-usb-phy + + reg: + minItems: 1 + maxItems: 2 + description: | + PHY0 and PHY2 share power and ground, PHY0 contains shared registers. + PHY0 and PHY2 must specify two register sets, where the first set is + PHY own registers and the second set is the PHY0 registers. + + clocks: + anyOf: + - items: + - description: Registers clock + - description: Main PHY clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: ULPI PHY clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: UTMI pads control registers clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: UTMI timeout clock + - description: UTMI pads control registers clock + + clock-names: + oneOf: + - items: + - const: reg + - const: pll_u + + - items: + - const: reg + - const: pll_u + - const: ulpi-link + + - items: + - const: reg + - const: pll_u + - const: utmi-pads + + - items: + - const: reg + - const: pll_u + - const: timer + - const: utmi-pads + + interrupts: + maxItems: 1 + + resets: + oneOf: + - maxItems: 1 + description: PHY reset + + - items: + - description: PHY reset + - description: UTMI pads reset + + reset-names: + oneOf: + - const: usb + + - items: + - const: usb + - const: utmi-pads + + "#phy-cells": + const: 0 + + phy_type: + $ref: /schemas/types.yaml#/definitions/string + enum: [utmi, ulpi, hsic] + + dr_mode: + $ref: /schemas/types.yaml#/definitions/string + enum: [host, peripheral, otg] + default: host + + vbus-supply: + description: Regulator controlling USB VBUS. + + nvidia,has-legacy-mode: + description: | + Indicates whether this controller can operate in legacy mode + (as APX 2500 / 2600). In legacy mode some registers are accessed + through the APB_MISC base address instead of the USB controller. + type: boolean + + nvidia,is-wired: + description: | + Indicates whether we can do certain kind of power optimizations for + the devices that are always connected. e.g. modem. + type: boolean + + nvidia,has-utmi-pad-registers: + description: | + Indicates whether this controller contains the UTMI pad control + registers common to all USB controllers. + type: boolean + + nvidia,hssync-start-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: | + Number of 480 MHz clock cycles to wait before start of sync launches + RxActive. + + nvidia,elastic-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Variable FIFO Depth of elastic input store. + + nvidia,idle-wait-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: | + Number of 480 MHz clock cycles of idle to wait before declare IDLE. + + nvidia,term-range-adj: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Range adjustment on terminations. + + nvidia,xcvr-setup: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 127 + description: Input of XCVR cell, HS driver output control. + + nvidia,xcvr-setup-use-fuses: + description: Indicates that the value is read from the on-chip fuses. + type: boolean + + nvidia,xcvr-lsfslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: LS falling slew rate control. + + nvidia,xcvr-lsrslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: LS rising slew rate control. + + nvidia,xcvr-hsslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 511 + description: HS slew rate control. + + nvidia,hssquelch-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: HS squelch detector level. + + nvidia,hsdiscon-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: HS disconnect detector level. + + nvidia,phy-reset-gpio: + maxItems: 1 + description: GPIO used to reset the PHY. + + nvidia,pmc: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: Phandle to Power Management controller. + - description: USB controller ID. + description: + Phandle to Power Management controller. + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + - phy_type + +additionalProperties: false + +allOf: + - if: + properties: + phy_type: + const: utmi + + then: + properties: + reg: + minItems: 2 + maxItems: 2 + + resets: + maxItems: 2 + + reset-names: + maxItems: 2 + + required: + - nvidia,hssync-start-delay + - nvidia,elastic-limit + - nvidia,idle-wait-delay + - nvidia,term-range-adj + - nvidia,xcvr-lsfslew + - nvidia,xcvr-lsrslew + + anyOf: + - required: ["nvidia,xcvr-setup"] + - required: ["nvidia,xcvr-setup-use-fuses"] + + if: + properties: + compatible: + contains: + const: nvidia,tegra30-usb-phy + + then: + properties: + clocks: + maxItems: 3 + + clock-names: + items: + - const: reg + - const: pll_u + - const: utmi-pads + + required: + - nvidia,xcvr-hsslew + - nvidia,hssquelch-level + - nvidia,hsdiscon-level + + else: + properties: + clocks: + maxItems: 4 + + clock-names: + items: + - const: reg + - const: pll_u + - const: timer + - const: utmi-pads + + - if: + properties: + phy_type: + const: ulpi + + then: + properties: + reg: + minItems: 1 + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: + minItems: 2 + maxItems: 3 + + oneOf: + - items: + - const: reg + - const: pll_u + + - items: + - const: reg + - const: pll_u + - const: ulpi-link + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + maxItems: 2 + +examples: + - | + #include <dt-bindings/clock/tegra124-car.h> + + usb-phy@7d008000 { + compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; + reg = <0x7d008000 0x4000>, + <0x7d000000 0x4000>; + interrupts = <0 97 4>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + resets = <&tegra_car 59>, <&tegra_car 22>; + reset-names = "usb", "utmi-pads"; + #phy-cells = <0>; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + nvidia,pmc = <&tegra_pmc 2>; + }; + + - | + #include <dt-bindings/clock/tegra20-car.h> + + usb-phy@c5004000 { + compatible = "nvidia,tegra20-usb-phy"; + reg = <0xc5004000 0x4000>; + interrupts = <0 21 4>; + phy_type = "ulpi"; + clocks = <&tegra_car TEGRA20_CLK_USB2>, + <&tegra_car TEGRA20_CLK_PLL_U>, + <&tegra_car TEGRA20_CLK_CDEV2>; + clock-names = "reg", "pll_u", "ulpi-link"; + resets = <&tegra_car 58>, <&tegra_car 22>; + reset-names = "usb", "utmi-pads"; + #phy-cells = <0>; + nvidia,pmc = <&tegra_pmc 1>; + }; |