diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt | 199 |
1 files changed, 199 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt new file mode 100644 index 000000000..a50e74684 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -0,0 +1,199 @@ +Qualcomm QCS404 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,qcs404-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south and east TLMM + tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Defintiion: names for the cells of reg, must contain "north", "south" + and "east". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio119 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, + sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, hdmi_tx, hdmi_ddc, blsp_uart_tx_a2, blsp_spi2, m_voc, + qdss_cti_trig_in_a0, blsp_uart_rx_a2, qdss_tracectl_a, + blsp_uart2, aud_cdc, blsp_i2c_sda_a2, qdss_tracedata_a, + blsp_i2c_scl_a2, qdss_tracectl_b, qdss_cti_trig_in_b0, + blsp_uart1, blsp_spi_mosi_a1, blsp_spi_miso_a1, + qdss_tracedata_b, blsp_i2c1, blsp_spi_cs_n_a1, gcc_plltest, + blsp_spi_clk_a1, rgb_data0, blsp_uart5, blsp_spi5, + adsp_ext, rgb_data1, prng_rosc, rgb_data2, blsp_i2c5, + gcc_gp1_clk_b, rgb_data3, gcc_gp2_clk_b, blsp_spi0, + blsp_uart0, gcc_gp3_clk_b, blsp_i2c0, qdss_traceclk_b, + pcie_clk, nfc_irq, blsp_spi4, nfc_dwl, audio_ts, rgb_data4, + spi_lcd, blsp_uart_tx_b2, gcc_gp3_clk_a, rgb_data5, + blsp_uart_rx_b2, blsp_i2c_sda_b2, blsp_i2c_scl_b2, + pwm_led11, i2s_3_data0_a, ebi2_lcd, i2s_3_data1_a, + i2s_3_data2_a, atest_char, pwm_led3, i2s_3_data3_a, + pwm_led4, i2s_4, ebi2_a, dsd_clk_b, pwm_led5, pwm_led6, + pwm_led7, pwm_led8, pwm_led24, spkr_dac0, blsp_i2c4, + pwm_led9, pwm_led10, spdifrx_opt, pwm_led12, pwm_led13, + pwm_led14, wlan1_adc1, rgb_data_b0, pwm_led15, + blsp_spi_mosi_b1, wlan1_adc0, rgb_data_b1, pwm_led16, + blsp_spi_miso_b1, qdss_cti_trig_out_b0, wlan2_adc1, + rgb_data_b2, pwm_led17, blsp_spi_cs_n_b1, wlan2_adc0, + rgb_data_b3, pwm_led18, blsp_spi_clk_b1, rgb_data_b4, + pwm_led19, ext_mclk1_b, qdss_traceclk_a, rgb_data_b5, + pwm_led20, atest_char3, i2s_3_sck_b, ldo_update, bimc_dte0, + rgb_hsync, pwm_led21, i2s_3_ws_b, dbg_out, rgb_vsync, + i2s_3_data0_b, ldo_en, hdmi_dtest, rgb_de, i2s_3_data1_b, + hdmi_lbk9, rgb_clk, atest_char1, i2s_3_data2_b, ebi_cdc, + hdmi_lbk8, rgb_mdp, atest_char0, i2s_3_data3_b, hdmi_lbk7, + rgb_data_b6, rgb_data_b7, hdmi_lbk6, rgmii_int, cri_trng1, + rgmii_wol, cri_trng0, gcc_tlmm, rgmii_ck, rgmii_tx, + hdmi_lbk5, hdmi_pixel, hdmi_rcv, hdmi_lbk4, rgmii_ctl, + ext_lpass, rgmii_rx, cri_trng, hdmi_lbk3, hdmi_lbk2, + qdss_cti_trig_out_b1, rgmii_mdio, hdmi_lbk1, rgmii_mdc, + hdmi_lbk0, ir_in, wsa_en, rgb_data6, rgb_data7, + atest_char2, ebi_ch0, blsp_uart3, blsp_spi3, sd_write, + blsp_i2c3, gcc_gp1_clk_a, qdss_cti_trig_in_b1, + gcc_gp2_clk_a, ext_mclk0, mclk_in1, i2s_1, dsd_clk_a, + qdss_cti_trig_in_a1, rgmi_dll1, pwm_led22, pwm_led23, + qdss_cti_trig_out_a0, rgmi_dll2, pwm_led1, + qdss_cti_trig_out_a1, pwm_led2, i2s_2, pll_bist, + ext_mclk1_a, mclk_in2, bimc_dte1, i2s_3_sck_a, i2s_3_ws_a + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,qcs404-pinctrl"; + reg = <0x01000000 0x200000>, + <0x01300000 0x200000>, + <0x07b00000 0x200000>; + reg-names = "south", "north", "east"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 120>; + interrupt-controller; + #interrupt-cells = <2>; + }; |