diff options
Diffstat (limited to 'Documentation/hwmon/lm78.rst')
| -rw-r--r-- | Documentation/hwmon/lm78.rst | 80 |
1 files changed, 80 insertions, 0 deletions
diff --git a/Documentation/hwmon/lm78.rst b/Documentation/hwmon/lm78.rst new file mode 100644 index 000000000..cb7a4832f --- /dev/null +++ b/Documentation/hwmon/lm78.rst @@ -0,0 +1,80 @@ +Kernel driver lm78 +================== + +Supported chips: + + * National Semiconductor LM78 / LM78-J + + Prefix: 'lm78' + + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) + + Datasheet: Publicly available at the National Semiconductor website + + http://www.national.com/ + + * National Semiconductor LM79 + + Prefix: 'lm79' + + Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports) + + Datasheet: Publicly available at the National Semiconductor website + + http://www.national.com/ + + +Authors: + - Frodo Looijaard <frodol@dds.nl> + - Jean Delvare <jdelvare@suse.de> + +Description +----------- + +This driver implements support for the National Semiconductor LM78, LM78-J +and LM79. They are described as 'Microprocessor System Hardware Monitors'. + +There is almost no difference between the three supported chips. Functionally, +the LM78 and LM78-J are exactly identical. The LM79 has one more VID line, +which is used to report the lower voltages newer Pentium processors use. +From here on, LM7* means either of these three types. + +The LM7* implements one temperature sensor, three fan rotation speed sensors, +seven voltage sensors, VID lines, alarms, and some miscellaneous stuff. + +Temperatures are measured in degrees Celsius. An alarm is triggered once +when the Overtemperature Shutdown limit is crossed; it is triggered again +as soon as it drops below the Hysteresis value. A more useful behavior +can be found by setting the Hysteresis value to +127 degrees Celsius; in +this case, alarms are issued during all the time when the actual temperature +is above the Overtemperature Shutdown value. Measurements are guaranteed +between -55 and +125 degrees, with a resolution of 1 degree. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4 or 8) to give +the readings more range or accuracy. Not all RPM values can accurately be +represented, so some rounding is done. With a divider of 2, the lowest +representable value is around 2600 RPM. + +Voltage sensors (also known as IN sensors) report their values in volts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. Note that minimum in this case always means 'closest to +zero'; this is important for negative voltage measurements. All voltage +inputs can measure voltages between 0 and 4.08 volts, with a resolution +of 0.016 volt. + +The VID lines encode the core voltage value: the voltage level your processor +should work with. This is hardcoded by the mainboard and/or processor itself. +It is a value in volts. When it is unconnected, you will often find the +value 3.50 V here. + +If an alarm triggers, it will remain triggered until the hardware register +is read at least once. This means that the cause for the alarm may +already have disappeared! Note that in the current implementation, all +hardware registers are read whenever any data is read (unless it is less +than 1.5 seconds since the last update). This means that you can easily +miss once-only alarms. + +The LM7* only updates its values each 1.5 seconds; reading it more often +will do no harm, but will return 'old' values. |