diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 376 |
1 files changed, 376 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts new file mode 100644 index 000000000..f0f26af1e --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts @@ -0,0 +1,376 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * sc7280 CRD 3+ board device tree source + * + * Copyright 2022 Google LLC. + */ + +/dts-v1/; + +#include "sc7280-herobrine.dtsi" +#include "sc7280-herobrine-audio-wcd9385.dtsi" +#include "sc7280-herobrine-lte-sku.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+)"; + compatible = "google,zoglin", "google,hoglin", "qcom,sc7280"; + + /* FIXED REGULATORS */ + + /* + * On most herobrine boards PPVAR_SYS directly provides VREG_EDP_BL. + * However, on CRD there's an extra regulator in the way. Since this + * is expected to be uncommon, we'll leave the "vreg_edp_bl" label + * in the baseboard herobrine.dtsi point at "ppvar_sys" and then + * make a "_crd" specific version here. + */ + vreg_edp_bl_crd: vreg-edp-bl-crd-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_edp_bl_crd"; + + gpio = <&pm8350c_gpios 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&edp_bl_reg_en>; + + vin-supply = <&ppvar_sys>; + }; +}; + +/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ + +&apps_rsc { + pmg1110-regulators { + compatible = "qcom,pmg1110-rpmh-regulators"; + qcom,pmic-id = "k"; + + vreg_s1k_1p0: smps1 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + }; + }; +}; + +ap_tp_i2c: &i2c0 { + status = "okay"; + clock-frequency = <400000>; + + trackpad: trackpad@15 { + compatible = "hid-over-i2c"; + reg = <0x15>; + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_odl>; + + interrupt-parent = <&tlmm>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + + post-power-on-delay-ms = <20>; + hid-descr-addr = <0x0001>; + vdd-supply = <&pp3300_z1>; + + wakeup-source; + }; +}; + +&ap_sar_sensor_i2c { + status = "okay"; +}; + +&ap_sar_sensor0 { + status = "okay"; +}; + +&ap_sar_sensor1 { + status = "okay"; +}; + +ap_ts_pen_1v8: &i2c13 { + status = "okay"; + clock-frequency = <400000>; + + ap_ts: touchscreen@5c { + compatible = "hid-over-i2c"; + reg = <0x5c>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>; + + interrupt-parent = <&tlmm>; + interrupts = <55 IRQ_TYPE_LEVEL_LOW>; + + post-power-on-delay-ms = <500>; + hid-descr-addr = <0x0000>; + + vdd-supply = <&pp3300_left_in_mlb>; + }; +}; + +&mdss_edp { + status = "okay"; +}; + +&mdss_edp_phy { + status = "okay"; +}; + +/* For nvme */ +&pcie1 { + status = "okay"; +}; + +/* For nvme */ +&pcie1_phy { + status = "okay"; +}; + +&pm8350c_pwm_backlight { + power-supply = <&vreg_edp_bl_crd>; +}; + +/* For eMMC */ +&sdhc_1 { + status = "okay"; +}; + +/* For SD Card */ +&sdhc_2 { + status = "okay"; +}; + +/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */ + +/* + * This pin goes to the display panel but then doesn't actually do anything + * on the panel itself (it doesn't connect to the touchscreen controller). + * We'll set a pullup here just to park the line. + */ +&ts_rst_conn { + bias-pull-up; +}; + +/* PINCTRL - BOARD-SPECIFIC */ + +/* + * Methodology for gpio-line-names: + * - If a pin goes to CRD board and is named it gets that name. + * - If a pin goes to CRD board and is not named, it gets no name. + * - If a pin is totally internal to Qcard then it gets Qcard name. + * - If a pin is not hooked up on Qcard, it gets no name. + */ + +&pm8350c_gpios { + gpio-line-names = "FLASH_STROBE_1", /* 1 */ + "AP_SUSPEND", + "PM8008_1_RST_N", + "", + "", + "EDP_BL_REG_EN", + "PMIC_EDP_BL_EN", + "PMIC_EDP_BL_PWM", + ""; + + edp_bl_reg_en: edp-bl-reg-en-state { + pins = "gpio6"; + function = "normal"; + bias-disable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + }; +}; + +&tlmm { + gpio-line-names = "AP_TP_I2C_SDA", /* 0 */ + "AP_TP_I2C_SCL", + "PCIE1_RESET_N", + "PCIE1_WAKE_N", + "APPS_I2C_SDA", + "APPS_I2C_SCL", + "", + "TPAD_INT_N", + "", + "", + + "GNSS_L1_EN", /* 10 */ + "GNSS_L5_EN", + "QSPI_DATA_0", + "QSPI_DATA_1", + "QSPI_CLK", + "QSPI_CS_N_1", + /* + * AP_FLASH_WP is crossystem ABI. Schematics call it + * BIOS_FLASH_WP_L (the '_L' suffix is misleading, the + * signal is active high). + */ + "AP_FLASH_WP", + "", + "AP_EC_INT_N", + "", + + "CAM0_RST_N", /* 20 */ + "CAM1_RST_N", + "SM_DBG_UART_TX", + "SM_DBG_UART_RX", + "", + "PM8008_IRQ_1", + "HOST2WLAN_SOL", + "WLAN2HOST_SOL", + "MOS_BT_UART_CTS", + "MOS_BT_UART_RFR", + + "MOS_BT_UART_TX", /* 30 */ + "MOS_BT_UART_RX", + "", + "HUB_RST", + "", + "", + "", + "", + "", + "", + + "EC_SPI_MISO_GPIO40", /* 40 */ + "EC_SPI_MOSI_GPIO41", + "EC_SPI_CLK_GPIO42", + "EC_SPI_CS_GPIO43", + "", + "EARLY_EUD_EN", + "", + "DP_HOT_PLUG_DETECT", + "AP_BRD_ID_0", + "AP_BRD_ID_1", + + "AP_BRD_ID_2", /* 50 */ + "NVME_PWR_REG_EN", + "TS_I2C_SDA_CONN", + "TS_I2C_CLK_CONN", + "TS_RST_CONN", + "TS_INT_CONN", + "AP_I2C_TPM_SDA", + "AP_I2C_TPM_SCL", + "", + "", + + "EDP_HOT_PLUG_DET_N", /* 60 */ + "", + "", + "AMP_EN", + "CAM0_MCLK_GPIO_64", + "CAM1_MCLK_GPIO_65", + "", + "", + "", + "CCI_I2C_SDA0", + + "CCI_I2C_SCL0", /* 70 */ + "", + "", + "", + "", + "", + "", + "", + "", + "PCIE1_CLK_REQ_N", + + "EN_PP3300_DX_EDP", /* 80 */ + "US_EURO_HS_SEL", + "FORCED_USB_BOOT", + "WCD_RESET_N", + "MOS_WLAN_EN", + "MOS_BT_EN", + "MOS_SW_CTRL", + "MOS_PCIE0_RST", + "MOS_PCIE0_CLKREQ_N", + "MOS_PCIE0_WAKE_N", + + "MOS_LAA_AS_EN", /* 90 */ + "SD_CARD_DET_CONN", + "", + "", + "MOS_BT_WLAN_SLIMBUS_CLK", + "MOS_BT_WLAN_SLIMBUS_DAT0", + "", + "", + "", + "", + + "", /* 100 */ + "", + "", + "", + "H1_AP_INT_N", + "", + "AMP_BCLK", + "AMP_DIN", + "AMP_LRCLK", + "UIM1_DATA_GPIO_109", + + "UIM1_CLK_GPIO_110", /* 110 */ + "UIM1_RESET_GPIO_111", + "", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RESET", + "UIM1_PRESENT", + "SDM_RFFE0_CLK", + "SDM_RFFE0_DATA", + "", + + "SDM_RFFE1_DATA", /* 120 */ + "SC_GPIO_121", + "FASTBOOT_SEL_1", + "SC_GPIO_123", + "FASTBOOT_SEL_2", + "SM_RFFE4_CLK_GRFC_8", + "SM_RFFE4_DATA_GRFC_9", + "WLAN_COEX_UART1_RX", + "WLAN_COEX_UART1_TX", + "", + + "", /* 130 */ + "", + "", + "SDR_QLINK_REQ", + "SDR_QLINK_EN", + "QLINK0_WMSS_RESET_N", + "SMR526_QLINK1_REQ", + "SMR526_QLINK1_EN", + "SMR526_QLINK1_WMSS_RESET_N", + "", + + "SAR1_INT_N", /* 140 */ + "SAR0_INT_N", + "", + "", + "WCD_SWR_TX_CLK", + "WCD_SWR_TX_DATA0", + "WCD_SWR_TX_DATA1", + "WCD_SWR_RX_CLK", + "WCD_SWR_RX_DATA0", + "WCD_SWR_RX_DATA1", + + "DMIC01_CLK", /* 150 */ + "DMIC01_DATA", + "DMIC23_CLK", + "DMIC23_DATA", + "", + "", + "EC_IN_RW_N", + "EN_PP3300_HUB", + "WCD_SWR_TX_DATA2", + "", + + "", /* 160 */ + "", + "", + "", + "", + "", + "", + "", + "", + "", + + "", /* 170 */ + "MOS_BLE_UART_TX", + "MOS_BLE_UART_RX", + ""; +}; |