diff options
Diffstat (limited to 'debian/patches/features/arm64/quartz64/arm64-dts-rockchip-Add-SOQuartz-Model-A-baseboard.patch')
| -rw-r--r-- | debian/patches/features/arm64/quartz64/arm64-dts-rockchip-Add-SOQuartz-Model-A-baseboard.patch | 279 |
1 files changed, 279 insertions, 0 deletions
diff --git a/debian/patches/features/arm64/quartz64/arm64-dts-rockchip-Add-SOQuartz-Model-A-baseboard.patch b/debian/patches/features/arm64/quartz64/arm64-dts-rockchip-Add-SOQuartz-Model-A-baseboard.patch new file mode 100644 index 000000000..ae644e05f --- /dev/null +++ b/debian/patches/features/arm64/quartz64/arm64-dts-rockchip-Add-SOQuartz-Model-A-baseboard.patch @@ -0,0 +1,279 @@ +From: Andrew Powers-Holmes <aholmes@omnom.net> +Date: Wed, 16 Nov 2022 12:53:37 +0100 +Subject: [4/4] arm64: dts: rockchip: Add SOQuartz Model A baseboard +Origin: https://git.kernel.org/linus/afbaed737fb45bcae91e4606025fb31da71b9dfe + +This patch adds the device tree for the "Model A" baseboard for +the SOQuartz CM4 SoM, which is not to be confused with the +Quartz64 Model A, which is the same form factor and SoC, but is +not a CM4 carrier board. + +The board features a PCIe 2 x1 slot, USB 2 host ports, CSI/DSI +connectors, an eDP FFC connector, gigabit ethernet, HDMI, and a +12V DC barrel jack. Also present is a microSD card slot, 40-pin +GPIO, and a power and reset button. + +Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net> +[rebase, misc fixes, reword] +Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com> +Link: https://lore.kernel.org/r/20221116115337.541601-5-frattaroli.nicolas@gmail.com +Signed-off-by: Heiko Stuebner <heiko@sntech.de> +--- + arch/arm64/boot/dts/rockchip/Makefile | 1 + + .../dts/rockchip/rk3566-soquartz-model-a.dts | 232 ++++++++++++++++++ + 2 files changed, 233 insertions(+) + create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts + +diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile +index 071284a46bf7..0a76a2ebb5f6 100644 +--- a/arch/arm64/boot/dts/rockchip/Makefile ++++ b/arch/arm64/boot/dts/rockchip/Makefile +@@ -70,6 +70,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-roc-pc.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-blade.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb ++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-model-a.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb +diff --git a/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts +new file mode 100644 +index 000000000000..2208dbfb7f0a +--- /dev/null ++++ b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts +@@ -0,0 +1,232 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++ ++/dts-v1/; ++ ++#include "rk3566-soquartz.dtsi" ++ ++/ { ++ model = "PINE64 RK3566 SOQuartz on Model A carrier board"; ++ compatible = "pine64,soquartz-model-a", "pine64,soquartz", "rockchip,rk3566"; ++ ++ /* labeled DCIN_12V in schematic */ ++ vcc12v_dcin: vcc12v-dcin-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc12v_dcin"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <12000000>; ++ regulator-max-microvolt = <12000000>; ++ }; ++ ++ vcc5v0_usb: vcc5v0-usb-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc5v0_usb"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vcc12v_dcin>; ++ }; ++ ++ /* ++ * Labelled VCC3V0_SD in schematic to not conflict with PMIC ++ * regulator, it's 3.3v in actuality ++ */ ++ vcc3v0_sd: vcc3v0-sd-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v0_sd"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ vin-supply = <&vcc3v3_sys>; ++ }; ++ ++ vcc3v3_pcie: vcc3v3-pcie-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3_pcie"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ vin-supply = <&vcc12v_dcin>; ++ }; ++ ++ vcc12v_pcie: vcc12v-pcie-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc12v_pcie"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <12000000>; ++ regulator-max-microvolt = <12000000>; ++ vin-supply = <&vcc12v_dcin>; ++ }; ++}; ++ ++/* phy for pcie */ ++&combphy2 { ++ phy-supply = <&vcc3v3_sys>; ++ status = "okay"; ++}; ++ ++&gmac1 { ++ status = "okay"; ++}; ++ ++/* ++ * i2c1 is exposed on CM1 / Module1A ++ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu ++ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu ++ */ ++&i2c1 { ++ status = "okay"; ++ ++ /* ++ * the rtc interrupt is tied to PMIC_PWRON, ++ * it will force reset the board if triggered. ++ */ ++ pcf85063: rtc@51 { ++ compatible = "nxp,pcf85063"; ++ reg = <0x51>; ++ }; ++}; ++ ++/* ++ * i2c2 is exposed on CM1 / Module1A - to PI40 ++ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch ++ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3 ++ */ ++&i2c2 { ++ status = "disabled"; ++}; ++ ++/* ++ * i2c3 is exposed on CM1 / Module1A - to PI40 ++ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3 ++ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3 ++ */ ++&i2c3 { ++ status = "disabled"; ++}; ++ ++/* ++ * i2c4 is exposed on CM2 / Module1B - to PI40 ++ * pin 45 - GPIO24 - i2c4_scl_m1 ++ * pin 47 - GPIO23 - i2c4_sda_m1 ++ */ ++&i2c4 { ++ status = "disabled"; ++}; ++ ++/* ++ * i2s1_8ch is exposed on CM1 / Module1A - to PI40 ++ * pin 24 - GPIO26 - i2s1_sdi1_m1 ++ * pin 25 - GPIO21 - i2s1_sdo0_m1 ++ * pin 26 - GPIO19 - i2s1_lrck_tx_m1 ++ * pin 27 - GPIO20 - i2s1_sdi0_m1 ++ * pin 29 - GPIO16 - i2s1_sdi3_m1 ++ * pin 30 - GPIO6 - i2s1_sdi2_m1 ++ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3 ++ * pin 41 - GPIO25 - i2s1_sdo2_m1 ++ * pin 49 - GPIO18 - i2s1_sclk_tx_m1 ++ * pin 50 - GPIO17 - i2s1_mclk_m1 ++ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2 ++ */ ++&i2s1_8ch { ++ status = "disabled"; ++}; ++ ++&led_diy { ++ status = "okay"; ++}; ++ ++&led_work { ++ status = "okay"; ++}; ++ ++&pcie2x1 { ++ vpcie3v3-supply = <&vcc3v3_pcie>; ++ status = "okay"; ++}; ++ ++&rgmii_phy1 { ++ status = "okay"; ++}; ++ ++&rgmii_phy1 { ++ status = "okay"; ++}; ++ ++/* ++ * saradc is exposed on CM1 / Module1A - to J2 ++ * pin 94 - AIN1 - saradc_vin3 ++ * pin 96 - AIN0 - saradc_vin2 ++ */ ++&saradc { ++ status = "disabled"; ++}; ++ ++/* ++ * vmmc-supply is vcc3v3_sd on v1.0 and vcc3v0_sd on v1.1+ ++ * the soquartz SoM has SDMMC_PWR (CM1 pin 75) hardwired to vcc3v3_sys, ++ * so we use vcc3v3_sd here to ensure the regulator is enabled on older boards. ++ */ ++&sdmmc0 { ++ vmmc-supply = <&vcc3v3_sd>; ++ status = "okay"; ++}; ++ ++/* ++ * spi3 is exposed on CM1 / Module1A - to PI40 ++ * pin 37 - GPIO7 - spi3_cs1_m0 ++ * pin 38 - GPIO11 - spi3_clk_m0 ++ * pin 39 - GPIO8 - spi3_cs0_m0 ++ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch ++ * pin 44 - GPIO10 - spi3_mosi_m0 ++ */ ++&spi3 { ++ status = "disabled"; ++}; ++ ++/* ++ * uart2 is exposed on CM1 / Module1A - to PI40 ++ * pin 51 - GPIO15 - uart2_rx_m0 ++ * pin 55 - GPIO14 - uart2_tx_m0 ++ */ ++&uart2 { ++ status = "okay"; ++}; ++ ++/* ++ * uart7 is exposed on CM1 / Module1A - to PI40 ++ * pin 46 - GPIO22 - uart7_tx_m2 ++ * pin 47 - GPIO23 - uart7_rx_m2 ++ */ ++&uart7 { ++ status = "okay"; ++}; ++ ++&usb2phy0 { ++ status = "okay"; ++}; ++ ++&usb2phy0_otg { ++ phy-supply = <&vcc5v0_usb>; ++ status = "okay"; ++}; ++ ++&usb_host0_xhci { ++ status = "okay"; ++}; ++ ++&vbus { ++ vin-supply = <&vcc5v0_usb>; ++}; ++ ++&vcc3v3_sd { ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ status = "okay"; ++}; +-- +2.39.0 + |