diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-cpm.c')
-rw-r--r-- | drivers/i2c/busses/i2c-cpm.c | 717 |
1 files changed, 717 insertions, 0 deletions
diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c new file mode 100644 index 000000000..24d584a1c --- /dev/null +++ b/drivers/i2c/busses/i2c-cpm.c @@ -0,0 +1,717 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Freescale CPM1/CPM2 I2C interface. + * Copyright (c) 1999 Dan Malek (dmalek@jlc.net). + * + * moved into proper i2c interface; + * Brad Parker (brad@heeltoe.com) + * + * Parts from dbox2_i2c.c (cvs.tuxbox.org) + * (C) 2000-2001 Felix Domke (tmbinc@gmx.net), Gillem (htoa@gmx.net) + * + * (C) 2007 Montavista Software, Inc. + * Vitaly Bordug <vitb@kernel.crashing.org> + * + * Converted to of_platform_device. Renamed to i2c-cpm.c. + * (C) 2007,2008 Jochen Friedrich <jochen@scram.de> + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/errno.h> +#include <linux/stddef.h> +#include <linux/i2c.h> +#include <linux/io.h> +#include <linux/dma-mapping.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <sysdev/fsl_soc.h> +#include <asm/cpm.h> + +/* Try to define this if you have an older CPU (earlier than rev D4) */ +/* However, better use a GPIO based bitbang driver in this case :/ */ +#undef I2C_CHIP_ERRATA + +#define CPM_MAX_READ 513 +#define CPM_MAXBD 4 + +#define I2C_EB (0x10) /* Big endian mode */ +#define I2C_EB_CPM2 (0x30) /* Big endian mode, memory snoop */ + +#define DPRAM_BASE ((u8 __iomem __force *)cpm_muram_addr(0)) + +/* I2C parameter RAM. */ +struct i2c_ram { + ushort rbase; /* Rx Buffer descriptor base address */ + ushort tbase; /* Tx Buffer descriptor base address */ + u_char rfcr; /* Rx function code */ + u_char tfcr; /* Tx function code */ + ushort mrblr; /* Max receive buffer length */ + uint rstate; /* Internal */ + uint rdp; /* Internal */ + ushort rbptr; /* Rx Buffer descriptor pointer */ + ushort rbc; /* Internal */ + uint rxtmp; /* Internal */ + uint tstate; /* Internal */ + uint tdp; /* Internal */ + ushort tbptr; /* Tx Buffer descriptor pointer */ + ushort tbc; /* Internal */ + uint txtmp; /* Internal */ + char res1[4]; /* Reserved */ + ushort rpbase; /* Relocation pointer */ + char res2[2]; /* Reserved */ + /* The following elements are only for CPM2 */ + char res3[4]; /* Reserved */ + uint sdmatmp; /* Internal */ +}; + +#define I2COM_START 0x80 +#define I2COM_MASTER 0x01 +#define I2CER_TXE 0x10 +#define I2CER_BUSY 0x04 +#define I2CER_TXB 0x02 +#define I2CER_RXB 0x01 +#define I2MOD_EN 0x01 + +/* I2C Registers */ +struct i2c_reg { + u8 i2mod; + u8 res1[3]; + u8 i2add; + u8 res2[3]; + u8 i2brg; + u8 res3[3]; + u8 i2com; + u8 res4[3]; + u8 i2cer; + u8 res5[3]; + u8 i2cmr; +}; + +struct cpm_i2c { + char *base; + struct platform_device *ofdev; + struct i2c_adapter adap; + uint dp_addr; + int version; /* CPM1=1, CPM2=2 */ + int irq; + int cp_command; + int freq; + struct i2c_reg __iomem *i2c_reg; + struct i2c_ram __iomem *i2c_ram; + u16 i2c_addr; + wait_queue_head_t i2c_wait; + cbd_t __iomem *tbase; + cbd_t __iomem *rbase; + u_char *txbuf[CPM_MAXBD]; + u_char *rxbuf[CPM_MAXBD]; + dma_addr_t txdma[CPM_MAXBD]; + dma_addr_t rxdma[CPM_MAXBD]; +}; + +static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id) +{ + struct cpm_i2c *cpm; + struct i2c_reg __iomem *i2c_reg; + struct i2c_adapter *adap = dev_id; + int i; + + cpm = i2c_get_adapdata(dev_id); + i2c_reg = cpm->i2c_reg; + + /* Clear interrupt. */ + i = in_8(&i2c_reg->i2cer); + out_8(&i2c_reg->i2cer, i); + + dev_dbg(&adap->dev, "Interrupt: %x\n", i); + + wake_up(&cpm->i2c_wait); + + return i ? IRQ_HANDLED : IRQ_NONE; +} + +static void cpm_reset_i2c_params(struct cpm_i2c *cpm) +{ + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; + + /* Set up the I2C parameters in the parameter ram. */ + out_be16(&i2c_ram->tbase, (u8 __iomem *)cpm->tbase - DPRAM_BASE); + out_be16(&i2c_ram->rbase, (u8 __iomem *)cpm->rbase - DPRAM_BASE); + + if (cpm->version == 1) { + out_8(&i2c_ram->tfcr, I2C_EB); + out_8(&i2c_ram->rfcr, I2C_EB); + } else { + out_8(&i2c_ram->tfcr, I2C_EB_CPM2); + out_8(&i2c_ram->rfcr, I2C_EB_CPM2); + } + + out_be16(&i2c_ram->mrblr, CPM_MAX_READ); + + out_be32(&i2c_ram->rstate, 0); + out_be32(&i2c_ram->rdp, 0); + out_be16(&i2c_ram->rbptr, 0); + out_be16(&i2c_ram->rbc, 0); + out_be32(&i2c_ram->rxtmp, 0); + out_be32(&i2c_ram->tstate, 0); + out_be32(&i2c_ram->tdp, 0); + out_be16(&i2c_ram->tbptr, 0); + out_be16(&i2c_ram->tbc, 0); + out_be32(&i2c_ram->txtmp, 0); +} + +static void cpm_i2c_force_close(struct i2c_adapter *adap) +{ + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; + + dev_dbg(&adap->dev, "cpm_i2c_force_close()\n"); + + cpm_command(cpm->cp_command, CPM_CR_CLOSE_RX_BD); + + out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */ + out_8(&i2c_reg->i2cer, 0xff); +} + +static void cpm_i2c_parse_message(struct i2c_adapter *adap, + struct i2c_msg *pmsg, int num, int tx, int rx) +{ + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + u_char addr; + u_char *tb; + u_char *rb; + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + + tbdf = cpm->tbase + tx; + rbdf = cpm->rbase + rx; + + addr = i2c_8bit_addr_from_msg(pmsg); + + tb = cpm->txbuf[tx]; + rb = cpm->rxbuf[rx]; + + /* Align read buffer */ + rb = (u_char *) (((ulong) rb + 1) & ~1); + + tb[0] = addr; /* Device address byte w/rw flag */ + + out_be16(&tbdf->cbd_datlen, pmsg->len + 1); + out_be16(&tbdf->cbd_sc, 0); + + if (!(pmsg->flags & I2C_M_NOSTART)) + setbits16(&tbdf->cbd_sc, BD_I2C_START); + + if (tx + 1 == num) + setbits16(&tbdf->cbd_sc, BD_SC_LAST | BD_SC_WRAP); + + if (pmsg->flags & I2C_M_RD) { + /* + * To read, we need an empty buffer of the proper length. + * All that is used is the first byte for address, the remainder + * is just used for timing (and doesn't really have to exist). + */ + + dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr); + + out_be16(&rbdf->cbd_datlen, 0); + out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT); + + if (rx + 1 == CPM_MAXBD) + setbits16(&rbdf->cbd_sc, BD_SC_WRAP); + + eieio(); + setbits16(&tbdf->cbd_sc, BD_SC_READY); + } else { + dev_dbg(&adap->dev, "cpm_i2c_write(abyte=0x%x)\n", addr); + + memcpy(tb+1, pmsg->buf, pmsg->len); + + eieio(); + setbits16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_INTRPT); + } +} + +static int cpm_i2c_check_message(struct i2c_adapter *adap, + struct i2c_msg *pmsg, int tx, int rx) +{ + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + u_char *tb; + u_char *rb; + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + + tbdf = cpm->tbase + tx; + rbdf = cpm->rbase + rx; + + tb = cpm->txbuf[tx]; + rb = cpm->rxbuf[rx]; + + /* Align read buffer */ + rb = (u_char *) (((uint) rb + 1) & ~1); + + eieio(); + if (pmsg->flags & I2C_M_RD) { + dev_dbg(&adap->dev, "tx sc 0x%04x, rx sc 0x%04x\n", + in_be16(&tbdf->cbd_sc), in_be16(&rbdf->cbd_sc)); + + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { + dev_dbg(&adap->dev, "I2C read; No ack\n"); + return -ENXIO; + } + if (in_be16(&rbdf->cbd_sc) & BD_SC_EMPTY) { + dev_err(&adap->dev, + "I2C read; complete but rbuf empty\n"); + return -EREMOTEIO; + } + if (in_be16(&rbdf->cbd_sc) & BD_SC_OV) { + dev_err(&adap->dev, "I2C read; Overrun\n"); + return -EREMOTEIO; + } + memcpy(pmsg->buf, rb, pmsg->len); + } else { + dev_dbg(&adap->dev, "tx sc %d 0x%04x\n", tx, + in_be16(&tbdf->cbd_sc)); + + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { + dev_dbg(&adap->dev, "I2C write; No ack\n"); + return -ENXIO; + } + if (in_be16(&tbdf->cbd_sc) & BD_SC_UN) { + dev_err(&adap->dev, "I2C write; Underrun\n"); + return -EIO; + } + if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) { + dev_err(&adap->dev, "I2C write; Collision\n"); + return -EIO; + } + } + return 0; +} + +static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) +{ + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; + struct i2c_msg *pmsg; + int ret; + int tptr; + int rptr; + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + + /* Reset to use first buffer */ + out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase)); + out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase)); + + tbdf = cpm->tbase; + rbdf = cpm->rbase; + + tptr = 0; + rptr = 0; + + /* + * If there was a collision in the last i2c transaction, + * Set I2COM_MASTER as it was cleared during collision. + */ + if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) { + out_8(&cpm->i2c_reg->i2com, I2COM_MASTER); + } + + while (tptr < num) { + pmsg = &msgs[tptr]; + dev_dbg(&adap->dev, "R: %d T: %d\n", rptr, tptr); + + cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr); + if (pmsg->flags & I2C_M_RD) + rptr++; + tptr++; + } + /* Start transfer now */ + /* Enable RX/TX/Error interupts */ + out_8(&i2c_reg->i2cmr, I2CER_TXE | I2CER_TXB | I2CER_RXB); + out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */ + /* Chip bug, set enable here */ + setbits8(&i2c_reg->i2mod, I2MOD_EN); /* Enable */ + /* Begin transmission */ + setbits8(&i2c_reg->i2com, I2COM_START); + + tptr = 0; + rptr = 0; + + while (tptr < num) { + /* Check for outstanding messages */ + dev_dbg(&adap->dev, "test ready.\n"); + pmsg = &msgs[tptr]; + if (pmsg->flags & I2C_M_RD) + ret = wait_event_timeout(cpm->i2c_wait, + (in_be16(&tbdf[tptr].cbd_sc) & BD_SC_NAK) || + !(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY), + 1 * HZ); + else + ret = wait_event_timeout(cpm->i2c_wait, + !(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_READY), + 1 * HZ); + if (ret == 0) { + ret = -EREMOTEIO; + dev_err(&adap->dev, "I2C transfer: timeout\n"); + goto out_err; + } + if (ret > 0) { + dev_dbg(&adap->dev, "ready.\n"); + ret = cpm_i2c_check_message(adap, pmsg, tptr, rptr); + tptr++; + if (pmsg->flags & I2C_M_RD) + rptr++; + if (ret) + goto out_err; + } + } +#ifdef I2C_CHIP_ERRATA + /* + * Chip errata, clear enable. This is not needed on rev D4 CPUs. + * Disabling I2C too early may cause too short stop condition + */ + udelay(4); + clrbits8(&i2c_reg->i2mod, I2MOD_EN); +#endif + return (num); + +out_err: + cpm_i2c_force_close(adap); +#ifdef I2C_CHIP_ERRATA + /* + * Chip errata, clear enable. This is not needed on rev D4 CPUs. + */ + clrbits8(&i2c_reg->i2mod, I2MOD_EN); +#endif + return ret; +} + +static u32 cpm_i2c_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); +} + +/* -----exported algorithm data: ------------------------------------- */ + +static const struct i2c_algorithm cpm_i2c_algo = { + .master_xfer = cpm_i2c_xfer, + .functionality = cpm_i2c_func, +}; + +/* CPM_MAX_READ is also limiting writes according to the code! */ +static const struct i2c_adapter_quirks cpm_i2c_quirks = { + .max_num_msgs = CPM_MAXBD, + .max_read_len = CPM_MAX_READ, + .max_write_len = CPM_MAX_READ, +}; + +static const struct i2c_adapter cpm_ops = { + .owner = THIS_MODULE, + .name = "i2c-cpm", + .algo = &cpm_i2c_algo, + .quirks = &cpm_i2c_quirks, +}; + +static int cpm_i2c_setup(struct cpm_i2c *cpm) +{ + struct platform_device *ofdev = cpm->ofdev; + const u32 *data; + int len, ret, i; + void __iomem *i2c_base; + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + unsigned char brg; + + dev_dbg(&cpm->ofdev->dev, "cpm_i2c_setup()\n"); + + init_waitqueue_head(&cpm->i2c_wait); + + cpm->irq = irq_of_parse_and_map(ofdev->dev.of_node, 0); + if (!cpm->irq) + return -EINVAL; + + /* Install interrupt handler. */ + ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c", + &cpm->adap); + if (ret) + return ret; + + /* I2C parameter RAM */ + i2c_base = of_iomap(ofdev->dev.of_node, 1); + if (i2c_base == NULL) { + ret = -EINVAL; + goto out_irq; + } + + if (of_device_is_compatible(ofdev->dev.of_node, "fsl,cpm1-i2c")) { + + /* Check for and use a microcode relocation patch. */ + cpm->i2c_ram = i2c_base; + cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase); + + /* + * Maybe should use cpm_muram_alloc instead of hardcoding + * this in micropatch.c + */ + if (cpm->i2c_addr) { + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); + iounmap(i2c_base); + } + + cpm->version = 1; + + } else if (of_device_is_compatible(ofdev->dev.of_node, "fsl,cpm2-i2c")) { + cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64); + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); + out_be16(i2c_base, cpm->i2c_addr); + iounmap(i2c_base); + + cpm->version = 2; + + } else { + iounmap(i2c_base); + ret = -EINVAL; + goto out_irq; + } + + /* I2C control/status registers */ + cpm->i2c_reg = of_iomap(ofdev->dev.of_node, 0); + if (cpm->i2c_reg == NULL) { + ret = -EINVAL; + goto out_ram; + } + + data = of_get_property(ofdev->dev.of_node, "fsl,cpm-command", &len); + if (!data || len != 4) { + ret = -EINVAL; + goto out_reg; + } + cpm->cp_command = *data; + + data = of_get_property(ofdev->dev.of_node, "linux,i2c-class", &len); + if (data && len == 4) + cpm->adap.class = *data; + + data = of_get_property(ofdev->dev.of_node, "clock-frequency", &len); + if (data && len == 4) + cpm->freq = *data; + else + cpm->freq = 60000; /* use 60kHz i2c clock by default */ + + /* + * Allocate space for CPM_MAXBD transmit and receive buffer + * descriptors in the DP ram. + */ + cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8); + if (!cpm->dp_addr) { + ret = -ENOMEM; + goto out_reg; + } + + cpm->tbase = cpm_muram_addr(cpm->dp_addr); + cpm->rbase = cpm_muram_addr(cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD); + + /* Allocate TX and RX buffers */ + + tbdf = cpm->tbase; + rbdf = cpm->rbase; + + for (i = 0; i < CPM_MAXBD; i++) { + cpm->rxbuf[i] = dma_alloc_coherent(&cpm->ofdev->dev, + CPM_MAX_READ + 1, + &cpm->rxdma[i], GFP_KERNEL); + if (!cpm->rxbuf[i]) { + ret = -ENOMEM; + goto out_muram; + } + out_be32(&rbdf[i].cbd_bufaddr, ((cpm->rxdma[i] + 1) & ~1)); + + cpm->txbuf[i] = dma_alloc_coherent(&cpm->ofdev->dev, + CPM_MAX_READ + 1, + &cpm->txdma[i], GFP_KERNEL); + if (!cpm->txbuf[i]) { + ret = -ENOMEM; + goto out_muram; + } + out_be32(&tbdf[i].cbd_bufaddr, cpm->txdma[i]); + } + + /* Initialize Tx/Rx parameters. */ + + cpm_reset_i2c_params(cpm); + + dev_dbg(&cpm->ofdev->dev, "i2c_ram 0x%p, i2c_addr 0x%04x, freq %d\n", + cpm->i2c_ram, cpm->i2c_addr, cpm->freq); + dev_dbg(&cpm->ofdev->dev, "tbase 0x%04x, rbase 0x%04x\n", + (u8 __iomem *)cpm->tbase - DPRAM_BASE, + (u8 __iomem *)cpm->rbase - DPRAM_BASE); + + cpm_command(cpm->cp_command, CPM_CR_INIT_TRX); + + /* + * Select an invalid address. Just make sure we don't use loopback mode + */ + out_8(&cpm->i2c_reg->i2add, 0x7f << 1); + + /* + * PDIV is set to 00 in i2mod, so brgclk/32 is used as input to the + * i2c baud rate generator. This is divided by 2 x (DIV + 3) to get + * the actual i2c bus frequency. + */ + brg = get_brgfreq() / (32 * 2 * cpm->freq) - 3; + out_8(&cpm->i2c_reg->i2brg, brg); + + out_8(&cpm->i2c_reg->i2mod, 0x00); + out_8(&cpm->i2c_reg->i2com, I2COM_MASTER); /* Master mode */ + + /* Disable interrupts. */ + out_8(&cpm->i2c_reg->i2cmr, 0); + out_8(&cpm->i2c_reg->i2cer, 0xff); + + return 0; + +out_muram: + for (i = 0; i < CPM_MAXBD; i++) { + if (cpm->rxbuf[i]) + dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, + cpm->rxbuf[i], cpm->rxdma[i]); + if (cpm->txbuf[i]) + dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, + cpm->txbuf[i], cpm->txdma[i]); + } + cpm_muram_free(cpm->dp_addr); +out_reg: + iounmap(cpm->i2c_reg); +out_ram: + if ((cpm->version == 1) && (!cpm->i2c_addr)) + iounmap(cpm->i2c_ram); + if (cpm->version == 2) + cpm_muram_free(cpm->i2c_addr); +out_irq: + free_irq(cpm->irq, &cpm->adap); + return ret; +} + +static void cpm_i2c_shutdown(struct cpm_i2c *cpm) +{ + int i; + + /* Shut down I2C. */ + clrbits8(&cpm->i2c_reg->i2mod, I2MOD_EN); + + /* Disable interrupts */ + out_8(&cpm->i2c_reg->i2cmr, 0); + out_8(&cpm->i2c_reg->i2cer, 0xff); + + free_irq(cpm->irq, &cpm->adap); + + /* Free all memory */ + for (i = 0; i < CPM_MAXBD; i++) { + dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, + cpm->rxbuf[i], cpm->rxdma[i]); + dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, + cpm->txbuf[i], cpm->txdma[i]); + } + + cpm_muram_free(cpm->dp_addr); + iounmap(cpm->i2c_reg); + + if ((cpm->version == 1) && (!cpm->i2c_addr)) + iounmap(cpm->i2c_ram); + if (cpm->version == 2) + cpm_muram_free(cpm->i2c_addr); +} + +static int cpm_i2c_probe(struct platform_device *ofdev) +{ + int result, len; + struct cpm_i2c *cpm; + const u32 *data; + + cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL); + if (!cpm) + return -ENOMEM; + + cpm->ofdev = ofdev; + + platform_set_drvdata(ofdev, cpm); + + cpm->adap = cpm_ops; + i2c_set_adapdata(&cpm->adap, cpm); + cpm->adap.dev.parent = &ofdev->dev; + cpm->adap.dev.of_node = of_node_get(ofdev->dev.of_node); + + result = cpm_i2c_setup(cpm); + if (result) { + dev_err(&ofdev->dev, "Unable to init hardware\n"); + goto out_free; + } + + /* register new adapter to i2c module... */ + + data = of_get_property(ofdev->dev.of_node, "linux,i2c-index", &len); + cpm->adap.nr = (data && len == 4) ? be32_to_cpup(data) : -1; + result = i2c_add_numbered_adapter(&cpm->adap); + + if (result < 0) + goto out_shut; + + dev_dbg(&ofdev->dev, "hw routines for %s registered.\n", + cpm->adap.name); + + return 0; +out_shut: + cpm_i2c_shutdown(cpm); +out_free: + kfree(cpm); + + return result; +} + +static int cpm_i2c_remove(struct platform_device *ofdev) +{ + struct cpm_i2c *cpm = platform_get_drvdata(ofdev); + + i2c_del_adapter(&cpm->adap); + + cpm_i2c_shutdown(cpm); + + kfree(cpm); + + return 0; +} + +static const struct of_device_id cpm_i2c_match[] = { + { + .compatible = "fsl,cpm1-i2c", + }, + { + .compatible = "fsl,cpm2-i2c", + }, + {}, +}; + +MODULE_DEVICE_TABLE(of, cpm_i2c_match); + +static struct platform_driver cpm_i2c_driver = { + .probe = cpm_i2c_probe, + .remove = cpm_i2c_remove, + .driver = { + .name = "fsl-i2c-cpm", + .of_match_table = cpm_i2c_match, + }, +}; + +module_platform_driver(cpm_i2c_driver); + +MODULE_AUTHOR("Jochen Friedrich <jochen@scram.de>"); +MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards"); +MODULE_LICENSE("GPL"); |