diff options
Diffstat (limited to 'drivers/pinctrl/qcom/pinctrl-spmi-gpio.c')
| -rw-r--r-- | drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 1262 |
1 files changed, 1262 insertions, 0 deletions
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c new file mode 100644 index 000000000..8c31a8f6b --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c @@ -0,0 +1,1262 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2012-2014, 2016-2021 The Linux Foundation. All rights reserved. + * Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <linux/gpio/driver.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_irq.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/spmi.h> +#include <linux/types.h> + +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +#include "../core.h" +#include "../pinctrl-utils.h" + +#define PMIC_GPIO_ADDRESS_RANGE 0x100 + +/* type and subtype registers base address offsets */ +#define PMIC_GPIO_REG_TYPE 0x4 +#define PMIC_GPIO_REG_SUBTYPE 0x5 + +/* GPIO peripheral type and subtype out_values */ +#define PMIC_GPIO_TYPE 0x10 +#define PMIC_GPIO_SUBTYPE_GPIO_4CH 0x1 +#define PMIC_GPIO_SUBTYPE_GPIOC_4CH 0x5 +#define PMIC_GPIO_SUBTYPE_GPIO_8CH 0x9 +#define PMIC_GPIO_SUBTYPE_GPIOC_8CH 0xd +#define PMIC_GPIO_SUBTYPE_GPIO_LV 0x10 +#define PMIC_GPIO_SUBTYPE_GPIO_MV 0x11 +#define PMIC_GPIO_SUBTYPE_GPIO_LV_VIN2 0x12 +#define PMIC_GPIO_SUBTYPE_GPIO_MV_VIN3 0x13 + +#define PMIC_MPP_REG_RT_STS 0x10 +#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1 + +/* control register base address offsets */ +#define PMIC_GPIO_REG_MODE_CTL 0x40 +#define PMIC_GPIO_REG_DIG_VIN_CTL 0x41 +#define PMIC_GPIO_REG_DIG_PULL_CTL 0x42 +#define PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL 0x44 +#define PMIC_GPIO_REG_DIG_IN_CTL 0x43 +#define PMIC_GPIO_REG_DIG_OUT_CTL 0x45 +#define PMIC_GPIO_REG_EN_CTL 0x46 +#define PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL 0x4A + +/* PMIC_GPIO_REG_MODE_CTL */ +#define PMIC_GPIO_REG_MODE_VALUE_SHIFT 0x1 +#define PMIC_GPIO_REG_MODE_FUNCTION_SHIFT 1 +#define PMIC_GPIO_REG_MODE_FUNCTION_MASK 0x7 +#define PMIC_GPIO_REG_MODE_DIR_SHIFT 4 +#define PMIC_GPIO_REG_MODE_DIR_MASK 0x7 + +#define PMIC_GPIO_MODE_DIGITAL_INPUT 0 +#define PMIC_GPIO_MODE_DIGITAL_OUTPUT 1 +#define PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT 2 +#define PMIC_GPIO_MODE_ANALOG_PASS_THRU 3 +#define PMIC_GPIO_REG_LV_MV_MODE_DIR_MASK 0x3 + +/* PMIC_GPIO_REG_DIG_VIN_CTL */ +#define PMIC_GPIO_REG_VIN_SHIFT 0 +#define PMIC_GPIO_REG_VIN_MASK 0x7 + +/* PMIC_GPIO_REG_DIG_PULL_CTL */ +#define PMIC_GPIO_REG_PULL_SHIFT 0 +#define PMIC_GPIO_REG_PULL_MASK 0x7 + +#define PMIC_GPIO_PULL_DOWN 4 +#define PMIC_GPIO_PULL_DISABLE 5 + +/* PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL for LV/MV */ +#define PMIC_GPIO_LV_MV_OUTPUT_INVERT 0x80 +#define PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT 7 +#define PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK 0xF + +/* PMIC_GPIO_REG_DIG_IN_CTL */ +#define PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN 0x80 +#define PMIC_GPIO_LV_MV_DIG_IN_DTEST_SEL_MASK 0x7 +#define PMIC_GPIO_DIG_IN_DTEST_SEL_MASK 0xf + +/* PMIC_GPIO_REG_DIG_OUT_CTL */ +#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT 0 +#define PMIC_GPIO_REG_OUT_STRENGTH_MASK 0x3 +#define PMIC_GPIO_REG_OUT_TYPE_SHIFT 4 +#define PMIC_GPIO_REG_OUT_TYPE_MASK 0x3 + +/* + * Output type - indicates pin should be configured as push-pull, + * open drain or open source. + */ +#define PMIC_GPIO_OUT_BUF_CMOS 0 +#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS 1 +#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS 2 + +#define PMIC_GPIO_OUT_STRENGTH_LOW 1 +#define PMIC_GPIO_OUT_STRENGTH_HIGH 3 + +/* PMIC_GPIO_REG_EN_CTL */ +#define PMIC_GPIO_REG_MASTER_EN_SHIFT 7 + +#define PMIC_GPIO_PHYSICAL_OFFSET 1 + +/* PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL */ +#define PMIC_GPIO_LV_MV_ANA_MUX_SEL_MASK 0x3 + +/* Qualcomm specific pin configurations */ +#define PMIC_GPIO_CONF_PULL_UP (PIN_CONFIG_END + 1) +#define PMIC_GPIO_CONF_STRENGTH (PIN_CONFIG_END + 2) +#define PMIC_GPIO_CONF_ATEST (PIN_CONFIG_END + 3) +#define PMIC_GPIO_CONF_ANALOG_PASS (PIN_CONFIG_END + 4) +#define PMIC_GPIO_CONF_DTEST_BUFFER (PIN_CONFIG_END + 5) + +/* The index of each function in pmic_gpio_functions[] array */ +enum pmic_gpio_func_index { + PMIC_GPIO_FUNC_INDEX_NORMAL, + PMIC_GPIO_FUNC_INDEX_PAIRED, + PMIC_GPIO_FUNC_INDEX_FUNC1, + PMIC_GPIO_FUNC_INDEX_FUNC2, + PMIC_GPIO_FUNC_INDEX_FUNC3, + PMIC_GPIO_FUNC_INDEX_FUNC4, + PMIC_GPIO_FUNC_INDEX_DTEST1, + PMIC_GPIO_FUNC_INDEX_DTEST2, + PMIC_GPIO_FUNC_INDEX_DTEST3, + PMIC_GPIO_FUNC_INDEX_DTEST4, +}; + +/** + * struct pmic_gpio_pad - keep current GPIO settings + * @base: Address base in SPMI device. + * @is_enabled: Set to false when GPIO should be put in high Z state. + * @out_value: Cached pin output value + * @have_buffer: Set to true if GPIO output could be configured in push-pull, + * open-drain or open-source mode. + * @output_enabled: Set to true if GPIO output logic is enabled. + * @input_enabled: Set to true if GPIO input buffer logic is enabled. + * @analog_pass: Set to true if GPIO is in analog-pass-through mode. + * @lv_mv_type: Set to true if GPIO subtype is GPIO_LV(0x10) or GPIO_MV(0x11). + * @num_sources: Number of power-sources supported by this GPIO. + * @power_source: Current power-source used. + * @buffer_type: Push-pull, open-drain or open-source. + * @pullup: Constant current which flow trough GPIO output buffer. + * @strength: No, Low, Medium, High + * @function: See pmic_gpio_functions[] + * @atest: the ATEST selection for GPIO analog-pass-through mode + * @dtest_buffer: the DTEST buffer selection for digital input mode. + */ +struct pmic_gpio_pad { + u16 base; + bool is_enabled; + bool out_value; + bool have_buffer; + bool output_enabled; + bool input_enabled; + bool analog_pass; + bool lv_mv_type; + unsigned int num_sources; + unsigned int power_source; + unsigned int buffer_type; + unsigned int pullup; + unsigned int strength; + unsigned int function; + unsigned int atest; + unsigned int dtest_buffer; +}; + +struct pmic_gpio_state { + struct device *dev; + struct regmap *map; + struct pinctrl_dev *ctrl; + struct gpio_chip chip; + u8 usid; + u8 pid_base; +}; + +static const struct pinconf_generic_params pmic_gpio_bindings[] = { + {"qcom,pull-up-strength", PMIC_GPIO_CONF_PULL_UP, 0}, + {"qcom,drive-strength", PMIC_GPIO_CONF_STRENGTH, 0}, + {"qcom,atest", PMIC_GPIO_CONF_ATEST, 0}, + {"qcom,analog-pass", PMIC_GPIO_CONF_ANALOG_PASS, 0}, + {"qcom,dtest-buffer", PMIC_GPIO_CONF_DTEST_BUFFER, 0}, +}; + +#ifdef CONFIG_DEBUG_FS +static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = { + PCONFDUMP(PMIC_GPIO_CONF_PULL_UP, "pull up strength", NULL, true), + PCONFDUMP(PMIC_GPIO_CONF_STRENGTH, "drive-strength", NULL, true), + PCONFDUMP(PMIC_GPIO_CONF_ATEST, "atest", NULL, true), + PCONFDUMP(PMIC_GPIO_CONF_ANALOG_PASS, "analog-pass", NULL, true), + PCONFDUMP(PMIC_GPIO_CONF_DTEST_BUFFER, "dtest-buffer", NULL, true), +}; +#endif + +static const char *const pmic_gpio_groups[] = { + "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", + "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", + "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29", + "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36", +}; + +static const char *const pmic_gpio_functions[] = { + [PMIC_GPIO_FUNC_INDEX_NORMAL] = PMIC_GPIO_FUNC_NORMAL, + [PMIC_GPIO_FUNC_INDEX_PAIRED] = PMIC_GPIO_FUNC_PAIRED, + [PMIC_GPIO_FUNC_INDEX_FUNC1] = PMIC_GPIO_FUNC_FUNC1, + [PMIC_GPIO_FUNC_INDEX_FUNC2] = PMIC_GPIO_FUNC_FUNC2, + [PMIC_GPIO_FUNC_INDEX_FUNC3] = PMIC_GPIO_FUNC_FUNC3, + [PMIC_GPIO_FUNC_INDEX_FUNC4] = PMIC_GPIO_FUNC_FUNC4, + [PMIC_GPIO_FUNC_INDEX_DTEST1] = PMIC_GPIO_FUNC_DTEST1, + [PMIC_GPIO_FUNC_INDEX_DTEST2] = PMIC_GPIO_FUNC_DTEST2, + [PMIC_GPIO_FUNC_INDEX_DTEST3] = PMIC_GPIO_FUNC_DTEST3, + [PMIC_GPIO_FUNC_INDEX_DTEST4] = PMIC_GPIO_FUNC_DTEST4, +}; + +static int pmic_gpio_read(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad, unsigned int addr) +{ + unsigned int val; + int ret; + + ret = regmap_read(state->map, pad->base + addr, &val); + if (ret < 0) + dev_err(state->dev, "read 0x%x failed\n", addr); + else + ret = val; + + return ret; +} + +static int pmic_gpio_write(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad, unsigned int addr, + unsigned int val) +{ + int ret; + + ret = regmap_write(state->map, pad->base + addr, val); + if (ret < 0) + dev_err(state->dev, "write 0x%x failed\n", addr); + + return ret; +} + +static int pmic_gpio_get_groups_count(struct pinctrl_dev *pctldev) +{ + /* Every PIN is a group */ + return pctldev->desc->npins; +} + +static const char *pmic_gpio_get_group_name(struct pinctrl_dev *pctldev, + unsigned pin) +{ + return pctldev->desc->pins[pin].name; +} + +static int pmic_gpio_get_group_pins(struct pinctrl_dev *pctldev, unsigned pin, + const unsigned **pins, unsigned *num_pins) +{ + *pins = &pctldev->desc->pins[pin].number; + *num_pins = 1; + return 0; +} + +static const struct pinctrl_ops pmic_gpio_pinctrl_ops = { + .get_groups_count = pmic_gpio_get_groups_count, + .get_group_name = pmic_gpio_get_group_name, + .get_group_pins = pmic_gpio_get_group_pins, + .dt_node_to_map = pinconf_generic_dt_node_to_map_group, + .dt_free_map = pinctrl_utils_free_map, +}; + +static int pmic_gpio_get_functions_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(pmic_gpio_functions); +} + +static const char *pmic_gpio_get_function_name(struct pinctrl_dev *pctldev, + unsigned function) +{ + return pmic_gpio_functions[function]; +} + +static int pmic_gpio_get_function_groups(struct pinctrl_dev *pctldev, + unsigned function, + const char *const **groups, + unsigned *const num_qgroups) +{ + *groups = pmic_gpio_groups; + *num_qgroups = pctldev->desc->npins; + return 0; +} + +static int pmic_gpio_set_mux(struct pinctrl_dev *pctldev, unsigned function, + unsigned pin) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + unsigned int val; + int ret; + + if (function > PMIC_GPIO_FUNC_INDEX_DTEST4) { + pr_err("function: %d is not defined\n", function); + return -EINVAL; + } + + pad = pctldev->desc->pins[pin].drv_data; + /* + * Non-LV/MV subtypes only support 2 special functions, + * offsetting the dtestx function values by 2 + */ + if (!pad->lv_mv_type) { + if (function == PMIC_GPIO_FUNC_INDEX_FUNC3 || + function == PMIC_GPIO_FUNC_INDEX_FUNC4) { + pr_err("LV/MV subtype doesn't have func3/func4\n"); + return -EINVAL; + } + if (function >= PMIC_GPIO_FUNC_INDEX_DTEST1) + function -= (PMIC_GPIO_FUNC_INDEX_DTEST1 - + PMIC_GPIO_FUNC_INDEX_FUNC3); + } + + pad->function = function; + + if (pad->analog_pass) + val = PMIC_GPIO_MODE_ANALOG_PASS_THRU; + else if (pad->output_enabled && pad->input_enabled) + val = PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT; + else if (pad->output_enabled) + val = PMIC_GPIO_MODE_DIGITAL_OUTPUT; + else + val = PMIC_GPIO_MODE_DIGITAL_INPUT; + + if (pad->lv_mv_type) { + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_MODE_CTL, val); + if (ret < 0) + return ret; + + val = pad->atest - 1; + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL, val); + if (ret < 0) + return ret; + + val = pad->out_value + << PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT; + val |= pad->function + & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK; + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL, val); + if (ret < 0) + return ret; + } else { + val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT; + val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val); + if (ret < 0) + return ret; + } + + val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT; + + return pmic_gpio_write(state, pad, PMIC_GPIO_REG_EN_CTL, val); +} + +static const struct pinmux_ops pmic_gpio_pinmux_ops = { + .get_functions_count = pmic_gpio_get_functions_count, + .get_function_name = pmic_gpio_get_function_name, + .get_function_groups = pmic_gpio_get_function_groups, + .set_mux = pmic_gpio_set_mux, +}; + +static int pmic_gpio_config_get(struct pinctrl_dev *pctldev, + unsigned int pin, unsigned long *config) +{ + unsigned param = pinconf_to_config_param(*config); + struct pmic_gpio_pad *pad; + unsigned arg; + + pad = pctldev->desc->pins[pin].drv_data; + + switch (param) { + case PIN_CONFIG_DRIVE_PUSH_PULL: + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + if (pad->pullup != PMIC_GPIO_PULL_DOWN) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_BIAS_DISABLE: + if (pad->pullup != PMIC_GPIO_PULL_DISABLE) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_BIAS_PULL_UP: + if (pad->pullup != PMIC_GPIO_PULL_UP_30) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + if (pad->is_enabled) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_POWER_SOURCE: + arg = pad->power_source; + break; + case PIN_CONFIG_INPUT_ENABLE: + if (!pad->input_enabled) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_OUTPUT_ENABLE: + arg = pad->output_enabled; + break; + case PIN_CONFIG_OUTPUT: + arg = pad->out_value; + break; + case PMIC_GPIO_CONF_PULL_UP: + arg = pad->pullup; + break; + case PMIC_GPIO_CONF_STRENGTH: + switch (pad->strength) { + case PMIC_GPIO_OUT_STRENGTH_HIGH: + arg = PMIC_GPIO_STRENGTH_HIGH; + break; + case PMIC_GPIO_OUT_STRENGTH_LOW: + arg = PMIC_GPIO_STRENGTH_LOW; + break; + default: + arg = pad->strength; + break; + } + break; + case PMIC_GPIO_CONF_ATEST: + arg = pad->atest; + break; + case PMIC_GPIO_CONF_ANALOG_PASS: + arg = pad->analog_pass; + break; + case PMIC_GPIO_CONF_DTEST_BUFFER: + arg = pad->dtest_buffer; + break; + default: + return -EINVAL; + } + + *config = pinconf_to_config_packed(param, arg); + return 0; +} + +static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned nconfs) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + unsigned param, arg; + unsigned int val; + int i, ret; + + pad = pctldev->desc->pins[pin].drv_data; + + pad->is_enabled = true; + for (i = 0; i < nconfs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + + switch (param) { + case PIN_CONFIG_DRIVE_PUSH_PULL: + pad->buffer_type = PMIC_GPIO_OUT_BUF_CMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (!pad->have_buffer) + return -EINVAL; + pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + if (!pad->have_buffer) + return -EINVAL; + pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS; + break; + case PIN_CONFIG_BIAS_DISABLE: + pad->pullup = PMIC_GPIO_PULL_DISABLE; + break; + case PIN_CONFIG_BIAS_PULL_UP: + pad->pullup = PMIC_GPIO_PULL_UP_30; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + if (arg) + pad->pullup = PMIC_GPIO_PULL_DOWN; + else + pad->pullup = PMIC_GPIO_PULL_DISABLE; + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + pad->is_enabled = false; + break; + case PIN_CONFIG_POWER_SOURCE: + if (arg >= pad->num_sources) + return -EINVAL; + pad->power_source = arg; + break; + case PIN_CONFIG_INPUT_ENABLE: + pad->input_enabled = arg ? true : false; + break; + case PIN_CONFIG_OUTPUT_ENABLE: + pad->output_enabled = arg ? true : false; + break; + case PIN_CONFIG_OUTPUT: + pad->output_enabled = true; + pad->out_value = arg; + break; + case PMIC_GPIO_CONF_PULL_UP: + if (arg > PMIC_GPIO_PULL_UP_1P5_30) + return -EINVAL; + pad->pullup = arg; + break; + case PMIC_GPIO_CONF_STRENGTH: + if (arg > PMIC_GPIO_STRENGTH_LOW) + return -EINVAL; + switch (arg) { + case PMIC_GPIO_STRENGTH_HIGH: + pad->strength = PMIC_GPIO_OUT_STRENGTH_HIGH; + break; + case PMIC_GPIO_STRENGTH_LOW: + pad->strength = PMIC_GPIO_OUT_STRENGTH_LOW; + break; + default: + pad->strength = arg; + break; + } + break; + case PMIC_GPIO_CONF_ATEST: + if (!pad->lv_mv_type || arg > 4) + return -EINVAL; + pad->atest = arg; + break; + case PMIC_GPIO_CONF_ANALOG_PASS: + if (!pad->lv_mv_type) + return -EINVAL; + pad->analog_pass = true; + break; + case PMIC_GPIO_CONF_DTEST_BUFFER: + if (arg > 4) + return -EINVAL; + pad->dtest_buffer = arg; + break; + default: + return -EINVAL; + } + } + + val = pad->power_source << PMIC_GPIO_REG_VIN_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL, val); + if (ret < 0) + return ret; + + val = pad->pullup << PMIC_GPIO_REG_PULL_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL, val); + if (ret < 0) + return ret; + + val = pad->buffer_type << PMIC_GPIO_REG_OUT_TYPE_SHIFT; + val |= pad->strength << PMIC_GPIO_REG_OUT_STRENGTH_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL, val); + if (ret < 0) + return ret; + + if (pad->dtest_buffer == 0) { + val = 0; + } else { + if (pad->lv_mv_type) { + val = pad->dtest_buffer - 1; + val |= PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN; + } else { + val = BIT(pad->dtest_buffer - 1); + } + } + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_IN_CTL, val); + if (ret < 0) + return ret; + + if (pad->analog_pass) + val = PMIC_GPIO_MODE_ANALOG_PASS_THRU; + else if (pad->output_enabled && pad->input_enabled) + val = PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT; + else if (pad->output_enabled) + val = PMIC_GPIO_MODE_DIGITAL_OUTPUT; + else + val = PMIC_GPIO_MODE_DIGITAL_INPUT; + + if (pad->lv_mv_type) { + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_MODE_CTL, val); + if (ret < 0) + return ret; + + val = pad->atest - 1; + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL, val); + if (ret < 0) + return ret; + + val = pad->out_value + << PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT; + val |= pad->function + & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK; + ret = pmic_gpio_write(state, pad, + PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL, val); + if (ret < 0) + return ret; + } else { + val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT; + val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val); + if (ret < 0) + return ret; + } + + val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_EN_CTL, val); + + return ret; +} + +static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned pin) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + int ret, val, function; + + static const char *const biases[] = { + "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA", + "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull" + }; + static const char *const buffer_types[] = { + "push-pull", "open-drain", "open-source" + }; + static const char *const strengths[] = { + "no", "high", "medium", "low" + }; + + pad = pctldev->desc->pins[pin].drv_data; + + seq_printf(s, " gpio%-2d:", pin + PMIC_GPIO_PHYSICAL_OFFSET); + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_EN_CTL); + + if (val < 0 || !(val >> PMIC_GPIO_REG_MASTER_EN_SHIFT)) { + seq_puts(s, " ---"); + } else { + if (pad->input_enabled) { + ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS); + if (ret < 0) + return; + + ret &= PMIC_MPP_REG_RT_STS_VAL_MASK; + pad->out_value = ret; + } + /* + * For the non-LV/MV subtypes only 2 special functions are + * available, offsetting the dtest function values by 2. + */ + function = pad->function; + if (!pad->lv_mv_type && + pad->function >= PMIC_GPIO_FUNC_INDEX_FUNC3) + function += PMIC_GPIO_FUNC_INDEX_DTEST1 - + PMIC_GPIO_FUNC_INDEX_FUNC3; + + if (pad->analog_pass) + seq_puts(s, " analog-pass"); + else + seq_printf(s, " %-4s", + pad->output_enabled ? "out" : "in"); + seq_printf(s, " %-4s", pad->out_value ? "high" : "low"); + seq_printf(s, " %-7s", pmic_gpio_functions[function]); + seq_printf(s, " vin-%d", pad->power_source); + seq_printf(s, " %-27s", biases[pad->pullup]); + seq_printf(s, " %-10s", buffer_types[pad->buffer_type]); + seq_printf(s, " %-7s", strengths[pad->strength]); + seq_printf(s, " atest-%d", pad->atest); + seq_printf(s, " dtest-%d", pad->dtest_buffer); + } +} + +static const struct pinconf_ops pmic_gpio_pinconf_ops = { + .is_generic = true, + .pin_config_group_get = pmic_gpio_config_get, + .pin_config_group_set = pmic_gpio_config_set, + .pin_config_group_dbg_show = pmic_gpio_config_dbg_show, +}; + +static int pmic_gpio_direction_input(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1); + + return pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_direction_output(struct gpio_chip *chip, + unsigned pin, int val) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val); + + return pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_get(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + struct pmic_gpio_pad *pad; + int ret; + + pad = state->ctrl->desc->pins[pin].drv_data; + + if (!pad->is_enabled) + return -EINVAL; + + if (pad->input_enabled) { + ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS); + if (ret < 0) + return ret; + + pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK; + } + + return !!pad->out_value; +} + +static void pmic_gpio_set(struct gpio_chip *chip, unsigned pin, int value) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value); + + pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_of_xlate(struct gpio_chip *chip, + const struct of_phandle_args *gpio_desc, + u32 *flags) +{ + if (chip->of_gpio_n_cells < 2) + return -EINVAL; + + if (flags) + *flags = gpio_desc->args[1]; + + return gpio_desc->args[0] - PMIC_GPIO_PHYSICAL_OFFSET; +} + +static void pmic_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + unsigned i; + + for (i = 0; i < chip->ngpio; i++) { + pmic_gpio_config_dbg_show(state->ctrl, s, i); + seq_puts(s, "\n"); + } +} + +static const struct gpio_chip pmic_gpio_gpio_template = { + .direction_input = pmic_gpio_direction_input, + .direction_output = pmic_gpio_direction_output, + .get = pmic_gpio_get, + .set = pmic_gpio_set, + .request = gpiochip_generic_request, + .free = gpiochip_generic_free, + .of_xlate = pmic_gpio_of_xlate, + .dbg_show = pmic_gpio_dbg_show, +}; + +static int pmic_gpio_populate(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad) +{ + int type, subtype, val, dir; + + type = pmic_gpio_read(state, pad, PMIC_GPIO_REG_TYPE); + if (type < 0) + return type; + + if (type != PMIC_GPIO_TYPE) { + dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n", + type, pad->base); + return -ENODEV; + } + + subtype = pmic_gpio_read(state, pad, PMIC_GPIO_REG_SUBTYPE); + if (subtype < 0) + return subtype; + + switch (subtype) { + case PMIC_GPIO_SUBTYPE_GPIO_4CH: + pad->have_buffer = true; + fallthrough; + case PMIC_GPIO_SUBTYPE_GPIOC_4CH: + pad->num_sources = 4; + break; + case PMIC_GPIO_SUBTYPE_GPIO_8CH: + pad->have_buffer = true; + fallthrough; + case PMIC_GPIO_SUBTYPE_GPIOC_8CH: + pad->num_sources = 8; + break; + case PMIC_GPIO_SUBTYPE_GPIO_LV: + pad->num_sources = 1; + pad->have_buffer = true; + pad->lv_mv_type = true; + break; + case PMIC_GPIO_SUBTYPE_GPIO_MV: + pad->num_sources = 2; + pad->have_buffer = true; + pad->lv_mv_type = true; + break; + case PMIC_GPIO_SUBTYPE_GPIO_LV_VIN2: + pad->num_sources = 2; + pad->have_buffer = true; + pad->lv_mv_type = true; + break; + case PMIC_GPIO_SUBTYPE_GPIO_MV_VIN3: + pad->num_sources = 3; + pad->have_buffer = true; + pad->lv_mv_type = true; + break; + default: + dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype); + return -ENODEV; + } + + if (pad->lv_mv_type) { + val = pmic_gpio_read(state, pad, + PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL); + if (val < 0) + return val; + + pad->out_value = !!(val & PMIC_GPIO_LV_MV_OUTPUT_INVERT); + pad->function = val & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL); + if (val < 0) + return val; + + dir = val & PMIC_GPIO_REG_LV_MV_MODE_DIR_MASK; + } else { + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL); + if (val < 0) + return val; + + pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT; + dir &= PMIC_GPIO_REG_MODE_DIR_MASK; + pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK; + } + + switch (dir) { + case PMIC_GPIO_MODE_DIGITAL_INPUT: + pad->input_enabled = true; + pad->output_enabled = false; + break; + case PMIC_GPIO_MODE_DIGITAL_OUTPUT: + pad->input_enabled = false; + pad->output_enabled = true; + break; + case PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT: + pad->input_enabled = true; + pad->output_enabled = true; + break; + case PMIC_GPIO_MODE_ANALOG_PASS_THRU: + if (!pad->lv_mv_type) + return -ENODEV; + pad->analog_pass = true; + break; + default: + dev_err(state->dev, "unknown GPIO direction\n"); + return -ENODEV; + } + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL); + if (val < 0) + return val; + + pad->power_source = val >> PMIC_GPIO_REG_VIN_SHIFT; + pad->power_source &= PMIC_GPIO_REG_VIN_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL); + if (val < 0) + return val; + + pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT; + pad->pullup &= PMIC_GPIO_REG_PULL_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_IN_CTL); + if (val < 0) + return val; + + if (pad->lv_mv_type && (val & PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN)) + pad->dtest_buffer = + (val & PMIC_GPIO_LV_MV_DIG_IN_DTEST_SEL_MASK) + 1; + else if (!pad->lv_mv_type) + pad->dtest_buffer = ffs(val); + else + pad->dtest_buffer = 0; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL); + if (val < 0) + return val; + + pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT; + pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK; + + pad->buffer_type = val >> PMIC_GPIO_REG_OUT_TYPE_SHIFT; + pad->buffer_type &= PMIC_GPIO_REG_OUT_TYPE_MASK; + + if (pad->lv_mv_type) { + val = pmic_gpio_read(state, pad, + PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL); + if (val < 0) + return val; + pad->atest = (val & PMIC_GPIO_LV_MV_ANA_MUX_SEL_MASK) + 1; + } + + /* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */ + pad->is_enabled = true; + return 0; +} + +static int pmic_gpio_domain_translate(struct irq_domain *domain, + struct irq_fwspec *fwspec, + unsigned long *hwirq, + unsigned int *type) +{ + struct pmic_gpio_state *state = container_of(domain->host_data, + struct pmic_gpio_state, + chip); + + if (fwspec->param_count != 2 || + fwspec->param[0] < 1 || fwspec->param[0] > state->chip.ngpio) + return -EINVAL; + + *hwirq = fwspec->param[0] - PMIC_GPIO_PHYSICAL_OFFSET; + *type = fwspec->param[1]; + + return 0; +} + +static unsigned int pmic_gpio_child_offset_to_irq(struct gpio_chip *chip, + unsigned int offset) +{ + return offset + PMIC_GPIO_PHYSICAL_OFFSET; +} + +static int pmic_gpio_child_to_parent_hwirq(struct gpio_chip *chip, + unsigned int child_hwirq, + unsigned int child_type, + unsigned int *parent_hwirq, + unsigned int *parent_type) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + + *parent_hwirq = child_hwirq + state->pid_base; + *parent_type = child_type; + + return 0; +} + +static int pmic_gpio_populate_parent_fwspec(struct gpio_chip *chip, + union gpio_irq_fwspec *gfwspec, + unsigned int parent_hwirq, + unsigned int parent_type) +{ + struct pmic_gpio_state *state = gpiochip_get_data(chip); + struct irq_fwspec *fwspec = &gfwspec->fwspec; + + fwspec->fwnode = chip->irq.parent_domain->fwnode; + + fwspec->param_count = 4; + fwspec->param[0] = state->usid; + fwspec->param[1] = parent_hwirq; + /* param[2] must be left as 0 */ + fwspec->param[3] = parent_type; + + return 0; +} + +static void pmic_gpio_irq_mask(struct irq_data *data) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + + irq_chip_mask_parent(data); + gpiochip_disable_irq(gc, data->hwirq); +} + +static void pmic_gpio_irq_unmask(struct irq_data *data) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(data); + + gpiochip_enable_irq(gc, data->hwirq); + irq_chip_unmask_parent(data); +} + +static const struct irq_chip spmi_gpio_irq_chip = { + .name = "spmi-gpio", + .irq_ack = irq_chip_ack_parent, + .irq_mask = pmic_gpio_irq_mask, + .irq_unmask = pmic_gpio_irq_unmask, + .irq_set_type = irq_chip_set_type_parent, + .irq_set_wake = irq_chip_set_wake_parent, + .flags = IRQCHIP_IMMUTABLE | IRQCHIP_MASK_ON_SUSPEND, + GPIOCHIP_IRQ_RESOURCE_HELPERS, +}; + +static int pmic_gpio_probe(struct platform_device *pdev) +{ + struct irq_domain *parent_domain; + struct device_node *parent_node; + struct device *dev = &pdev->dev; + struct pinctrl_pin_desc *pindesc; + struct pinctrl_desc *pctrldesc; + struct pmic_gpio_pad *pad, *pads; + struct pmic_gpio_state *state; + struct gpio_irq_chip *girq; + const struct spmi_device *parent_spmi_dev; + int ret, npins, i; + u32 reg; + + ret = of_property_read_u32(dev->of_node, "reg", ®); + if (ret < 0) { + dev_err(dev, "missing base address"); + return ret; + } + + npins = (uintptr_t) device_get_match_data(&pdev->dev); + + state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL); + if (!state) + return -ENOMEM; + + platform_set_drvdata(pdev, state); + + state->dev = &pdev->dev; + state->map = dev_get_regmap(dev->parent, NULL); + parent_spmi_dev = to_spmi_device(dev->parent); + state->usid = parent_spmi_dev->usid; + state->pid_base = reg >> 8; + + pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL); + if (!pindesc) + return -ENOMEM; + + pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL); + if (!pads) + return -ENOMEM; + + pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL); + if (!pctrldesc) + return -ENOMEM; + + pctrldesc->pctlops = &pmic_gpio_pinctrl_ops; + pctrldesc->pmxops = &pmic_gpio_pinmux_ops; + pctrldesc->confops = &pmic_gpio_pinconf_ops; + pctrldesc->owner = THIS_MODULE; + pctrldesc->name = dev_name(dev); + pctrldesc->pins = pindesc; + pctrldesc->npins = npins; + pctrldesc->num_custom_params = ARRAY_SIZE(pmic_gpio_bindings); + pctrldesc->custom_params = pmic_gpio_bindings; +#ifdef CONFIG_DEBUG_FS + pctrldesc->custom_conf_items = pmic_conf_items; +#endif + + for (i = 0; i < npins; i++, pindesc++) { + pad = &pads[i]; + pindesc->drv_data = pad; + pindesc->number = i; + pindesc->name = pmic_gpio_groups[i]; + + pad->base = reg + i * PMIC_GPIO_ADDRESS_RANGE; + + ret = pmic_gpio_populate(state, pad); + if (ret < 0) + return ret; + } + + state->chip = pmic_gpio_gpio_template; + state->chip.parent = dev; + state->chip.base = -1; + state->chip.ngpio = npins; + state->chip.label = dev_name(dev); + state->chip.of_gpio_n_cells = 2; + state->chip.can_sleep = false; + + state->ctrl = devm_pinctrl_register(dev, pctrldesc, state); + if (IS_ERR(state->ctrl)) + return PTR_ERR(state->ctrl); + + parent_node = of_irq_find_parent(state->dev->of_node); + if (!parent_node) + return -ENXIO; + + parent_domain = irq_find_host(parent_node); + of_node_put(parent_node); + if (!parent_domain) + return -ENXIO; + + girq = &state->chip.irq; + gpio_irq_chip_set_chip(girq, &spmi_gpio_irq_chip); + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_level_irq; + girq->fwnode = of_node_to_fwnode(state->dev->of_node); + girq->parent_domain = parent_domain; + girq->child_to_parent_hwirq = pmic_gpio_child_to_parent_hwirq; + girq->populate_parent_alloc_arg = pmic_gpio_populate_parent_fwspec; + girq->child_offset_to_irq = pmic_gpio_child_offset_to_irq; + girq->child_irq_domain_ops.translate = pmic_gpio_domain_translate; + + ret = gpiochip_add_data(&state->chip, state); + if (ret) { + dev_err(state->dev, "can't add gpio chip\n"); + return ret; + } + + /* + * For DeviceTree-supported systems, the gpio core checks the + * pinctrl's device node for the "gpio-ranges" property. + * If it is present, it takes care of adding the pin ranges + * for the driver. In this case the driver can skip ahead. + * + * In order to remain compatible with older, existing DeviceTree + * files which don't set the "gpio-ranges" property or systems that + * utilize ACPI the driver has to call gpiochip_add_pin_range(). + */ + if (!of_property_read_bool(dev->of_node, "gpio-ranges")) { + ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, + npins); + if (ret) { + dev_err(dev, "failed to add pin range\n"); + goto err_range; + } + } + + return 0; + +err_range: + gpiochip_remove(&state->chip); + return ret; +} + +static int pmic_gpio_remove(struct platform_device *pdev) +{ + struct pmic_gpio_state *state = platform_get_drvdata(pdev); + + gpiochip_remove(&state->chip); + return 0; +} + +static const struct of_device_id pmic_gpio_of_match[] = { + { .compatible = "qcom,pm2250-gpio", .data = (void *) 10 }, + /* pm660 has 13 GPIOs with holes on 1, 5, 6, 7, 8 and 10 */ + { .compatible = "qcom,pm660-gpio", .data = (void *) 13 }, + /* pm660l has 12 GPIOs with holes on 1, 2, 10, 11 and 12 */ + { .compatible = "qcom,pm660l-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pm6125-gpio", .data = (void *) 9 }, + { .compatible = "qcom,pm6150-gpio", .data = (void *) 10 }, + { .compatible = "qcom,pm6150l-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pm6350-gpio", .data = (void *) 9 }, + { .compatible = "qcom,pm7250b-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pm7325-gpio", .data = (void *) 10 }, + { .compatible = "qcom,pm8005-gpio", .data = (void *) 4 }, + { .compatible = "qcom,pm8008-gpio", .data = (void *) 2 }, + { .compatible = "qcom,pm8019-gpio", .data = (void *) 6 }, + /* pm8150 has 10 GPIOs with holes on 2, 5, 7 and 8 */ + { .compatible = "qcom,pm8150-gpio", .data = (void *) 10 }, + { .compatible = "qcom,pmc8180-gpio", .data = (void *) 10 }, + /* pm8150b has 12 GPIOs with holes on 3, r and 7 */ + { .compatible = "qcom,pm8150b-gpio", .data = (void *) 12 }, + /* pm8150l has 12 GPIOs with holes on 7 */ + { .compatible = "qcom,pm8150l-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pmc8180c-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pm8226-gpio", .data = (void *) 8 }, + { .compatible = "qcom,pm8350-gpio", .data = (void *) 10 }, + { .compatible = "qcom,pm8350b-gpio", .data = (void *) 8 }, + { .compatible = "qcom,pm8350c-gpio", .data = (void *) 9 }, + { .compatible = "qcom,pm8450-gpio", .data = (void *) 4 }, + { .compatible = "qcom,pm8916-gpio", .data = (void *) 4 }, + { .compatible = "qcom,pm8941-gpio", .data = (void *) 36 }, + /* pm8950 has 8 GPIOs with holes on 3 */ + { .compatible = "qcom,pm8950-gpio", .data = (void *) 8 }, + { .compatible = "qcom,pm8994-gpio", .data = (void *) 22 }, + { .compatible = "qcom,pm8998-gpio", .data = (void *) 26 }, + { .compatible = "qcom,pma8084-gpio", .data = (void *) 22 }, + { .compatible = "qcom,pmi8950-gpio", .data = (void *) 2 }, + { .compatible = "qcom,pmi8994-gpio", .data = (void *) 10 }, + { .compatible = "qcom,pmi8998-gpio", .data = (void *) 14 }, + { .compatible = "qcom,pmk8350-gpio", .data = (void *) 4 }, + { .compatible = "qcom,pmm8155au-gpio", .data = (void *) 10 }, + /* pmp8074 has 12 GPIOs with holes on 1 and 12 */ + { .compatible = "qcom,pmp8074-gpio", .data = (void *) 12 }, + { .compatible = "qcom,pmr735a-gpio", .data = (void *) 4 }, + { .compatible = "qcom,pmr735b-gpio", .data = (void *) 4 }, + /* pms405 has 12 GPIOs with holes on 1, 9, and 10 */ + { .compatible = "qcom,pms405-gpio", .data = (void *) 12 }, + /* pmx55 has 11 GPIOs with holes on 3, 7, 10, 11 */ + { .compatible = "qcom,pmx55-gpio", .data = (void *) 11 }, + { .compatible = "qcom,pmx65-gpio", .data = (void *) 16 }, + { }, +}; + +MODULE_DEVICE_TABLE(of, pmic_gpio_of_match); + +static struct platform_driver pmic_gpio_driver = { + .driver = { + .name = "qcom-spmi-gpio", + .of_match_table = pmic_gpio_of_match, + }, + .probe = pmic_gpio_probe, + .remove = pmic_gpio_remove, +}; + +module_platform_driver(pmic_gpio_driver); + +MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>"); +MODULE_DESCRIPTION("Qualcomm SPMI PMIC GPIO pin control driver"); +MODULE_ALIAS("platform:qcom-spmi-gpio"); +MODULE_LICENSE("GPL v2"); |