diff options
Diffstat (limited to 'drivers/tty/serial/icom.c')
| -rw-r--r-- | drivers/tty/serial/icom.c | 1876 |
1 files changed, 1876 insertions, 0 deletions
diff --git a/drivers/tty/serial/icom.c b/drivers/tty/serial/icom.c new file mode 100644 index 000000000..819f957b6 --- /dev/null +++ b/drivers/tty/serial/icom.c @@ -0,0 +1,1876 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * icom.c + * + * Copyright (C) 2001 IBM Corporation. All rights reserved. + * + * Serial device driver. + * + * Based on code from serial.c + */ +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/signal.h> +#include <linux/timer.h> +#include <linux/interrupt.h> +#include <linux/tty.h> +#include <linux/termios.h> +#include <linux/fs.h> +#include <linux/tty_flip.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> +#include <linux/major.h> +#include <linux/string.h> +#include <linux/fcntl.h> +#include <linux/ptrace.h> +#include <linux/ioport.h> +#include <linux/mm.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/vmalloc.h> +#include <linux/smp.h> +#include <linux/spinlock.h> +#include <linux/kref.h> +#include <linux/firmware.h> +#include <linux/bitops.h> + +#include <linux/io.h> +#include <asm/irq.h> +#include <linux/uaccess.h> + +/*#define ICOM_TRACE enable port trace capabilities */ + +#define ICOM_DRIVER_NAME "icom" +#define NR_PORTS 128 + +static const unsigned int icom_acfg_baud[] = { + 300, + 600, + 900, + 1200, + 1800, + 2400, + 3600, + 4800, + 7200, + 9600, + 14400, + 19200, + 28800, + 38400, + 57600, + 76800, + 115200, + 153600, + 230400, + 307200, + 460800, +}; +#define BAUD_TABLE_LIMIT (ARRAY_SIZE(icom_acfg_baud) - 1) + +struct icom_regs { + u32 control; /* Adapter Control Register */ + u32 interrupt; /* Adapter Interrupt Register */ + u32 int_mask; /* Adapter Interrupt Mask Reg */ + u32 int_pri; /* Adapter Interrupt Priority r */ + u32 int_reg_b; /* Adapter non-masked Interrupt */ + u32 resvd01; + u32 resvd02; + u32 resvd03; + u32 control_2; /* Adapter Control Register 2 */ + u32 interrupt_2; /* Adapter Interrupt Register 2 */ + u32 int_mask_2; /* Adapter Interrupt Mask 2 */ + u32 int_pri_2; /* Adapter Interrupt Prior 2 */ + u32 int_reg_2b; /* Adapter non-masked 2 */ +}; + +struct func_dram { + u32 reserved[108]; /* 0-1B0 reserved by personality code */ + u32 RcvStatusAddr; /* 1B0-1B3 Status Address for Next rcv */ + u8 RcvStnAddr; /* 1B4 Receive Station Addr */ + u8 IdleState; /* 1B5 Idle State */ + u8 IdleMonitor; /* 1B6 Idle Monitor */ + u8 FlagFillIdleTimer; /* 1B7 Flag Fill Idle Timer */ + u32 XmitStatusAddr; /* 1B8-1BB Transmit Status Address */ + u8 StartXmitCmd; /* 1BC Start Xmit Command */ + u8 HDLCConfigReg; /* 1BD Reserved */ + u8 CauseCode; /* 1BE Cause code for fatal error */ + u8 xchar; /* 1BF High priority send */ + u32 reserved3; /* 1C0-1C3 Reserved */ + u8 PrevCmdReg; /* 1C4 Reserved */ + u8 CmdReg; /* 1C5 Command Register */ + u8 async_config2; /* 1C6 Async Config Byte 2 */ + u8 async_config3; /* 1C7 Async Config Byte 3 */ + u8 dce_resvd[20]; /* 1C8-1DB DCE Rsvd */ + u8 dce_resvd21; /* 1DC DCE Rsvd (21st byte */ + u8 misc_flags; /* 1DD misc flags */ +#define V2_HARDWARE 0x40 +#define ICOM_HDW_ACTIVE 0x01 + u8 call_length; /* 1DE Phone #/CFI buff ln */ + u8 call_length2; /* 1DF Upper byte (unused) */ + u32 call_addr; /* 1E0-1E3 Phn #/CFI buff addr */ + u16 timer_value; /* 1E4-1E5 general timer value */ + u8 timer_command; /* 1E6 general timer cmd */ + u8 dce_command; /* 1E7 dce command reg */ + u8 dce_cmd_status; /* 1E8 dce command stat */ + u8 x21_r1_ioff; /* 1E9 dce ready counter */ + u8 x21_r0_ioff; /* 1EA dce not ready ctr */ + u8 x21_ralt_ioff; /* 1EB dce CNR counter */ + u8 x21_r1_ion; /* 1EC dce ready I on ctr */ + u8 rsvd_ier; /* 1ED Rsvd for IER (if ne */ + u8 ier; /* 1EE Interrupt Enable */ + u8 isr; /* 1EF Input Signal Reg */ + u8 osr; /* 1F0 Output Signal Reg */ + u8 reset; /* 1F1 Reset/Reload Reg */ + u8 disable; /* 1F2 Disable Reg */ + u8 sync; /* 1F3 Sync Reg */ + u8 error_stat; /* 1F4 Error Status */ + u8 cable_id; /* 1F5 Cable ID */ + u8 cs_length; /* 1F6 CS Load Length */ + u8 mac_length; /* 1F7 Mac Load Length */ + u32 cs_load_addr; /* 1F8-1FB Call Load PCI Addr */ + u32 mac_load_addr; /* 1FC-1FF Mac Load PCI Addr */ +}; + +/* + * adapter defines and structures + */ +#define ICOM_CONTROL_START_A 0x00000008 +#define ICOM_CONTROL_STOP_A 0x00000004 +#define ICOM_CONTROL_START_B 0x00000002 +#define ICOM_CONTROL_STOP_B 0x00000001 +#define ICOM_CONTROL_START_C 0x00000008 +#define ICOM_CONTROL_STOP_C 0x00000004 +#define ICOM_CONTROL_START_D 0x00000002 +#define ICOM_CONTROL_STOP_D 0x00000001 +#define ICOM_IRAM_OFFSET 0x1000 +#define ICOM_IRAM_SIZE 0x0C00 +#define ICOM_DCE_IRAM_OFFSET 0x0A00 +#define ICOM_CABLE_ID_VALID 0x01 +#define ICOM_CABLE_ID_MASK 0xF0 +#define ICOM_DISABLE 0x80 +#define CMD_XMIT_RCV_ENABLE 0xC0 +#define CMD_XMIT_ENABLE 0x40 +#define CMD_RCV_DISABLE 0x00 +#define CMD_RCV_ENABLE 0x80 +#define CMD_RESTART 0x01 +#define CMD_HOLD_XMIT 0x02 +#define CMD_SND_BREAK 0x04 +#define RS232_CABLE 0x06 +#define V24_CABLE 0x0E +#define V35_CABLE 0x0C +#define V36_CABLE 0x02 +#define NO_CABLE 0x00 +#define START_DOWNLOAD 0x80 +#define ICOM_INT_MASK_PRC_A 0x00003FFF +#define ICOM_INT_MASK_PRC_B 0x3FFF0000 +#define ICOM_INT_MASK_PRC_C 0x00003FFF +#define ICOM_INT_MASK_PRC_D 0x3FFF0000 +#define INT_RCV_COMPLETED 0x1000 +#define INT_XMIT_COMPLETED 0x2000 +#define INT_IDLE_DETECT 0x0800 +#define INT_RCV_DISABLED 0x0400 +#define INT_XMIT_DISABLED 0x0200 +#define INT_RCV_XMIT_SHUTDOWN 0x0100 +#define INT_FATAL_ERROR 0x0080 +#define INT_CABLE_PULL 0x0020 +#define INT_SIGNAL_CHANGE 0x0010 +#define HDLC_PPP_PURE_ASYNC 0x02 +#define HDLC_FF_FILL 0x00 +#define HDLC_HDW_FLOW 0x01 +#define START_XMIT 0x80 +#define ICOM_ACFG_DRIVE1 0x20 +#define ICOM_ACFG_NO_PARITY 0x00 +#define ICOM_ACFG_PARITY_ENAB 0x02 +#define ICOM_ACFG_PARITY_ODD 0x01 +#define ICOM_ACFG_8BPC 0x00 +#define ICOM_ACFG_7BPC 0x04 +#define ICOM_ACFG_6BPC 0x08 +#define ICOM_ACFG_5BPC 0x0C +#define ICOM_ACFG_1STOP_BIT 0x00 +#define ICOM_ACFG_2STOP_BIT 0x10 +#define ICOM_DTR 0x80 +#define ICOM_RTS 0x40 +#define ICOM_RI 0x08 +#define ICOM_DSR 0x80 +#define ICOM_DCD 0x20 +#define ICOM_CTS 0x40 + +#define NUM_XBUFFS 1 +#define NUM_RBUFFS 2 +#define RCV_BUFF_SZ 0x0200 +#define XMIT_BUFF_SZ 0x1000 +struct statusArea { + /**********************************************/ + /* Transmit Status Area */ + /**********************************************/ + struct xmit_status_area{ + __le32 leNext; /* Next entry in Little Endian on Adapter */ + __le32 leNextASD; + __le32 leBuffer; /* Buffer for entry in LE for Adapter */ + __le16 leLengthASD; + __le16 leOffsetASD; + __le16 leLength; /* Length of data in segment */ + __le16 flags; +#define SA_FLAGS_DONE 0x0080 /* Done with Segment */ +#define SA_FLAGS_CONTINUED 0x8000 /* More Segments */ +#define SA_FLAGS_IDLE 0x4000 /* Mark IDLE after frm */ +#define SA_FLAGS_READY_TO_XMIT 0x0800 +#define SA_FLAGS_STAT_MASK 0x007F + } xmit[NUM_XBUFFS]; + + /**********************************************/ + /* Receive Status Area */ + /**********************************************/ + struct { + __le32 leNext; /* Next entry in Little Endian on Adapter */ + __le32 leNextASD; + __le32 leBuffer; /* Buffer for entry in LE for Adapter */ + __le16 WorkingLength; /* size of segment */ + __le16 reserv01; + __le16 leLength; /* Length of data in segment */ + __le16 flags; +#define SA_FL_RCV_DONE 0x0010 /* Data ready */ +#define SA_FLAGS_OVERRUN 0x0040 +#define SA_FLAGS_PARITY_ERROR 0x0080 +#define SA_FLAGS_FRAME_ERROR 0x0001 +#define SA_FLAGS_FRAME_TRUNC 0x0002 +#define SA_FLAGS_BREAK_DET 0x0004 /* set conditionally by device driver, not hardware */ +#define SA_FLAGS_RCV_MASK 0xFFE6 + } rcv[NUM_RBUFFS]; +}; + +struct icom_adapter; + + +#define ICOM_MAJOR 243 +#define ICOM_MINOR_START 0 + +struct icom_port { + struct uart_port uart_port; + unsigned char cable_id; + unsigned char read_status_mask; + unsigned char ignore_status_mask; + void __iomem * int_reg; + struct icom_regs __iomem *global_reg; + struct func_dram __iomem *dram; + int port; + struct statusArea *statStg; + dma_addr_t statStg_pci; + __le32 *xmitRestart; + dma_addr_t xmitRestart_pci; + unsigned char *xmit_buf; + dma_addr_t xmit_buf_pci; + unsigned char *recv_buf; + dma_addr_t recv_buf_pci; + int next_rcv; + int status; +#define ICOM_PORT_ACTIVE 1 /* Port exists. */ +#define ICOM_PORT_OFF 0 /* Port does not exist. */ + struct icom_adapter *adapter; +}; + +struct icom_adapter { + void __iomem * base_addr; + unsigned long base_addr_pci; + struct pci_dev *pci_dev; + struct icom_port port_info[4]; + int index; + int version; +#define ADAPTER_V1 0x0001 +#define ADAPTER_V2 0x0002 + u32 subsystem_id; +#define FOUR_PORT_MODEL 0x0252 +#define V2_TWO_PORTS_RVX 0x021A +#define V2_ONE_PORT_RVX_ONE_PORT_IMBED_MDM 0x0251 + int numb_ports; + struct list_head icom_adapter_entry; + struct kref kref; +}; + +/* prototype */ +extern void iCom_sercons_init(void); + +struct lookup_proc_table { + u32 __iomem *global_control_reg; + unsigned long processor_id; +}; + +struct lookup_int_table { + u32 __iomem *global_int_mask; + unsigned long processor_id; +}; + +static inline struct icom_port *to_icom_port(struct uart_port *port) +{ + return container_of(port, struct icom_port, uart_port); +} + +static const struct pci_device_id icom_pci_table[] = { + { + .vendor = PCI_VENDOR_ID_IBM, + .device = PCI_DEVICE_ID_IBM_ICOM_DEV_ID_1, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = ADAPTER_V1, + }, + { + .vendor = PCI_VENDOR_ID_IBM, + .device = PCI_DEVICE_ID_IBM_ICOM_DEV_ID_2, + .subvendor = PCI_VENDOR_ID_IBM, + .subdevice = PCI_DEVICE_ID_IBM_ICOM_V2_TWO_PORTS_RVX, + .driver_data = ADAPTER_V2, + }, + { + .vendor = PCI_VENDOR_ID_IBM, + .device = PCI_DEVICE_ID_IBM_ICOM_DEV_ID_2, + .subvendor = PCI_VENDOR_ID_IBM, + .subdevice = PCI_DEVICE_ID_IBM_ICOM_V2_ONE_PORT_RVX_ONE_PORT_MDM, + .driver_data = ADAPTER_V2, + }, + { + .vendor = PCI_VENDOR_ID_IBM, + .device = PCI_DEVICE_ID_IBM_ICOM_DEV_ID_2, + .subvendor = PCI_VENDOR_ID_IBM, + .subdevice = PCI_DEVICE_ID_IBM_ICOM_FOUR_PORT_MODEL, + .driver_data = ADAPTER_V2, + }, + { + .vendor = PCI_VENDOR_ID_IBM, + .device = PCI_DEVICE_ID_IBM_ICOM_DEV_ID_2, + .subvendor = PCI_VENDOR_ID_IBM, + .subdevice = PCI_DEVICE_ID_IBM_ICOM_V2_ONE_PORT_RVX_ONE_PORT_MDM_PCIE, + .driver_data = ADAPTER_V2, + }, + {} +}; + +static struct lookup_proc_table start_proc[4] = { + {NULL, ICOM_CONTROL_START_A}, + {NULL, ICOM_CONTROL_START_B}, + {NULL, ICOM_CONTROL_START_C}, + {NULL, ICOM_CONTROL_START_D} +}; + + +static struct lookup_proc_table stop_proc[4] = { + {NULL, ICOM_CONTROL_STOP_A}, + {NULL, ICOM_CONTROL_STOP_B}, + {NULL, ICOM_CONTROL_STOP_C}, + {NULL, ICOM_CONTROL_STOP_D} +}; + +static struct lookup_int_table int_mask_tbl[4] = { + {NULL, ICOM_INT_MASK_PRC_A}, + {NULL, ICOM_INT_MASK_PRC_B}, + {NULL, ICOM_INT_MASK_PRC_C}, + {NULL, ICOM_INT_MASK_PRC_D}, +}; + + +MODULE_DEVICE_TABLE(pci, icom_pci_table); + +static LIST_HEAD(icom_adapter_head); + +/* spinlock for adapter initialization and changing adapter operations */ +static DEFINE_SPINLOCK(icom_lock); + +#ifdef ICOM_TRACE +static inline void trace(struct icom_port *icom_port, char *trace_pt, + unsigned long trace_data) +{ + dev_info(&icom_port->adapter->pci_dev->dev, ":%d:%s - %lx\n", + icom_port->port, trace_pt, trace_data); +} +#else +static inline void trace(struct icom_port *icom_port, char *trace_pt, unsigned long trace_data) {}; +#endif +static void icom_kref_release(struct kref *kref); + +static void free_port_memory(struct icom_port *icom_port) +{ + struct pci_dev *dev = icom_port->adapter->pci_dev; + + trace(icom_port, "RET_PORT_MEM", 0); + if (icom_port->recv_buf) { + dma_free_coherent(&dev->dev, 4096, icom_port->recv_buf, + icom_port->recv_buf_pci); + icom_port->recv_buf = NULL; + } + if (icom_port->xmit_buf) { + dma_free_coherent(&dev->dev, 4096, icom_port->xmit_buf, + icom_port->xmit_buf_pci); + icom_port->xmit_buf = NULL; + } + if (icom_port->statStg) { + dma_free_coherent(&dev->dev, 4096, icom_port->statStg, + icom_port->statStg_pci); + icom_port->statStg = NULL; + } + + if (icom_port->xmitRestart) { + dma_free_coherent(&dev->dev, 4096, icom_port->xmitRestart, + icom_port->xmitRestart_pci); + icom_port->xmitRestart = NULL; + } +} + +static int get_port_memory(struct icom_port *icom_port) +{ + int index; + unsigned long stgAddr; + unsigned long startStgAddr; + unsigned long offset; + struct pci_dev *dev = icom_port->adapter->pci_dev; + + icom_port->xmit_buf = + dma_alloc_coherent(&dev->dev, 4096, &icom_port->xmit_buf_pci, + GFP_KERNEL); + if (!icom_port->xmit_buf) { + dev_err(&dev->dev, "Can not allocate Transmit buffer\n"); + return -ENOMEM; + } + + trace(icom_port, "GET_PORT_MEM", + (unsigned long) icom_port->xmit_buf); + + icom_port->recv_buf = + dma_alloc_coherent(&dev->dev, 4096, &icom_port->recv_buf_pci, + GFP_KERNEL); + if (!icom_port->recv_buf) { + dev_err(&dev->dev, "Can not allocate Receive buffer\n"); + free_port_memory(icom_port); + return -ENOMEM; + } + trace(icom_port, "GET_PORT_MEM", + (unsigned long) icom_port->recv_buf); + + icom_port->statStg = + dma_alloc_coherent(&dev->dev, 4096, &icom_port->statStg_pci, + GFP_KERNEL); + if (!icom_port->statStg) { + dev_err(&dev->dev, "Can not allocate Status buffer\n"); + free_port_memory(icom_port); + return -ENOMEM; + } + trace(icom_port, "GET_PORT_MEM", + (unsigned long) icom_port->statStg); + + icom_port->xmitRestart = + dma_alloc_coherent(&dev->dev, 4096, &icom_port->xmitRestart_pci, + GFP_KERNEL); + if (!icom_port->xmitRestart) { + dev_err(&dev->dev, + "Can not allocate xmit Restart buffer\n"); + free_port_memory(icom_port); + return -ENOMEM; + } + + /* FODs: Frame Out Descriptor Queue, this is a FIFO queue that + indicates that frames are to be transmitted + */ + + stgAddr = (unsigned long) icom_port->statStg; + for (index = 0; index < NUM_XBUFFS; index++) { + trace(icom_port, "FOD_ADDR", stgAddr); + stgAddr = stgAddr + sizeof(icom_port->statStg->xmit[0]); + if (index < (NUM_XBUFFS - 1)) { + memset(&icom_port->statStg->xmit[index], 0, sizeof(struct xmit_status_area)); + icom_port->statStg->xmit[index].leLengthASD = + cpu_to_le16(XMIT_BUFF_SZ); + trace(icom_port, "FOD_ADDR", stgAddr); + trace(icom_port, "FOD_XBUFF", + (unsigned long) icom_port->xmit_buf); + icom_port->statStg->xmit[index].leBuffer = + cpu_to_le32(icom_port->xmit_buf_pci); + } else if (index == (NUM_XBUFFS - 1)) { + memset(&icom_port->statStg->xmit[index], 0, sizeof(struct xmit_status_area)); + icom_port->statStg->xmit[index].leLengthASD = + cpu_to_le16(XMIT_BUFF_SZ); + trace(icom_port, "FOD_XBUFF", + (unsigned long) icom_port->xmit_buf); + icom_port->statStg->xmit[index].leBuffer = + cpu_to_le32(icom_port->xmit_buf_pci); + } else { + memset(&icom_port->statStg->xmit[index], 0, sizeof(struct xmit_status_area)); + } + } + /* FIDs */ + startStgAddr = stgAddr; + + /* fill in every entry, even if no buffer */ + for (index = 0; index < NUM_RBUFFS; index++) { + trace(icom_port, "FID_ADDR", stgAddr); + stgAddr = stgAddr + sizeof(icom_port->statStg->rcv[0]); + icom_port->statStg->rcv[index].leLength = 0; + icom_port->statStg->rcv[index].WorkingLength = + cpu_to_le16(RCV_BUFF_SZ); + if (index < (NUM_RBUFFS - 1) ) { + offset = stgAddr - (unsigned long) icom_port->statStg; + icom_port->statStg->rcv[index].leNext = + cpu_to_le32(icom_port-> statStg_pci + offset); + trace(icom_port, "FID_RBUFF", + (unsigned long) icom_port->recv_buf); + icom_port->statStg->rcv[index].leBuffer = + cpu_to_le32(icom_port->recv_buf_pci); + } else if (index == (NUM_RBUFFS -1) ) { + offset = startStgAddr - (unsigned long) icom_port->statStg; + icom_port->statStg->rcv[index].leNext = + cpu_to_le32(icom_port-> statStg_pci + offset); + trace(icom_port, "FID_RBUFF", + (unsigned long) icom_port->recv_buf + 2048); + icom_port->statStg->rcv[index].leBuffer = + cpu_to_le32(icom_port->recv_buf_pci + 2048); + } else { + icom_port->statStg->rcv[index].leNext = 0; + icom_port->statStg->rcv[index].leBuffer = 0; + } + } + + return 0; +} + +static void stop_processor(struct icom_port *icom_port) +{ + unsigned long temp; + unsigned long flags; + int port; + + spin_lock_irqsave(&icom_lock, flags); + + port = icom_port->port; + if (port >= ARRAY_SIZE(stop_proc)) { + dev_err(&icom_port->adapter->pci_dev->dev, + "Invalid port assignment\n"); + goto unlock; + } + + if (port == 0 || port == 1) + stop_proc[port].global_control_reg = &icom_port->global_reg->control; + else + stop_proc[port].global_control_reg = &icom_port->global_reg->control_2; + + temp = readl(stop_proc[port].global_control_reg); + temp = (temp & ~start_proc[port].processor_id) | stop_proc[port].processor_id; + writel(temp, stop_proc[port].global_control_reg); + + /* write flush */ + readl(stop_proc[port].global_control_reg); + +unlock: + spin_unlock_irqrestore(&icom_lock, flags); +} + +static void start_processor(struct icom_port *icom_port) +{ + unsigned long temp; + unsigned long flags; + int port; + + spin_lock_irqsave(&icom_lock, flags); + + port = icom_port->port; + if (port >= ARRAY_SIZE(start_proc)) { + dev_err(&icom_port->adapter->pci_dev->dev, + "Invalid port assignment\n"); + goto unlock; + } + + if (port == 0 || port == 1) + start_proc[port].global_control_reg = &icom_port->global_reg->control; + else + start_proc[port].global_control_reg = &icom_port->global_reg->control_2; + + temp = readl(start_proc[port].global_control_reg); + temp = (temp & ~stop_proc[port].processor_id) | start_proc[port].processor_id; + writel(temp, start_proc[port].global_control_reg); + + /* write flush */ + readl(start_proc[port].global_control_reg); + +unlock: + spin_unlock_irqrestore(&icom_lock, flags); +} + +static void load_code(struct icom_port *icom_port) +{ + const struct firmware *fw; + char __iomem *iram_ptr; + int index; + int status = 0; + void __iomem *dram_ptr = icom_port->dram; + dma_addr_t temp_pci; + unsigned char *new_page = NULL; + unsigned char cable_id = NO_CABLE; + struct pci_dev *dev = icom_port->adapter->pci_dev; + + /* Clear out any pending interrupts */ + writew(0x3FFF, icom_port->int_reg); + + trace(icom_port, "CLEAR_INTERRUPTS", 0); + + /* Stop processor */ + stop_processor(icom_port); + + /* Zero out DRAM */ + memset_io(dram_ptr, 0, 512); + + /* Load Call Setup into Adapter */ + if (request_firmware(&fw, "icom_call_setup.bin", &dev->dev) < 0) { + dev_err(&dev->dev,"Unable to load icom_call_setup.bin firmware image\n"); + status = -1; + goto load_code_exit; + } + + if (fw->size > ICOM_DCE_IRAM_OFFSET) { + dev_err(&dev->dev, "Invalid firmware image for icom_call_setup.bin found.\n"); + release_firmware(fw); + status = -1; + goto load_code_exit; + } + + iram_ptr = (char __iomem *)icom_port->dram + ICOM_IRAM_OFFSET; + for (index = 0; index < fw->size; index++) + writeb(fw->data[index], &iram_ptr[index]); + + release_firmware(fw); + + /* Load Resident DCE portion of Adapter */ + if (request_firmware(&fw, "icom_res_dce.bin", &dev->dev) < 0) { + dev_err(&dev->dev,"Unable to load icom_res_dce.bin firmware image\n"); + status = -1; + goto load_code_exit; + } + + if (fw->size > ICOM_IRAM_SIZE) { + dev_err(&dev->dev, "Invalid firmware image for icom_res_dce.bin found.\n"); + release_firmware(fw); + status = -1; + goto load_code_exit; + } + + iram_ptr = (char __iomem *) icom_port->dram + ICOM_IRAM_OFFSET; + for (index = ICOM_DCE_IRAM_OFFSET; index < fw->size; index++) + writeb(fw->data[index], &iram_ptr[index]); + + release_firmware(fw); + + /* Set Hardware level */ + if (icom_port->adapter->version == ADAPTER_V2) + writeb(V2_HARDWARE, &(icom_port->dram->misc_flags)); + + /* Start the processor in Adapter */ + start_processor(icom_port); + + writeb((HDLC_PPP_PURE_ASYNC | HDLC_FF_FILL), + &(icom_port->dram->HDLCConfigReg)); + writeb(0x04, &(icom_port->dram->FlagFillIdleTimer)); /* 0.5 seconds */ + writeb(0x00, &(icom_port->dram->CmdReg)); + writeb(0x10, &(icom_port->dram->async_config3)); + writeb((ICOM_ACFG_DRIVE1 | ICOM_ACFG_NO_PARITY | ICOM_ACFG_8BPC | + ICOM_ACFG_1STOP_BIT), &(icom_port->dram->async_config2)); + + /*Set up data in icom DRAM to indicate where personality + *code is located and its length. + */ + new_page = dma_alloc_coherent(&dev->dev, 4096, &temp_pci, GFP_KERNEL); + + if (!new_page) { + dev_err(&dev->dev, "Can not allocate DMA buffer\n"); + status = -1; + goto load_code_exit; + } + + if (request_firmware(&fw, "icom_asc.bin", &dev->dev) < 0) { + dev_err(&dev->dev,"Unable to load icom_asc.bin firmware image\n"); + status = -1; + goto load_code_exit; + } + + if (fw->size > ICOM_DCE_IRAM_OFFSET) { + dev_err(&dev->dev, "Invalid firmware image for icom_asc.bin found.\n"); + release_firmware(fw); + status = -1; + goto load_code_exit; + } + + for (index = 0; index < fw->size; index++) + new_page[index] = fw->data[index]; + + writeb((char) ((fw->size + 16)/16), &icom_port->dram->mac_length); + writel(temp_pci, &icom_port->dram->mac_load_addr); + + release_firmware(fw); + + /*Setting the syncReg to 0x80 causes adapter to start downloading + the personality code into adapter instruction RAM. + Once code is loaded, it will begin executing and, based on + information provided above, will start DMAing data from + shared memory to adapter DRAM. + */ + /* the wait loop below verifies this write operation has been done + and processed + */ + writeb(START_DOWNLOAD, &icom_port->dram->sync); + + /* Wait max 1 Sec for data download and processor to start */ + for (index = 0; index < 10; index++) { + msleep(100); + if (readb(&icom_port->dram->misc_flags) & ICOM_HDW_ACTIVE) + break; + } + + if (index == 10) + status = -1; + + /* + * check Cable ID + */ + cable_id = readb(&icom_port->dram->cable_id); + + if (cable_id & ICOM_CABLE_ID_VALID) { + /* Get cable ID into the lower 4 bits (standard form) */ + cable_id = (cable_id & ICOM_CABLE_ID_MASK) >> 4; + icom_port->cable_id = cable_id; + } else { + dev_err(&dev->dev,"Invalid or no cable attached\n"); + icom_port->cable_id = NO_CABLE; + } + + load_code_exit: + + if (status != 0) { + /* Clear out any pending interrupts */ + writew(0x3FFF, icom_port->int_reg); + + /* Turn off port */ + writeb(ICOM_DISABLE, &(icom_port->dram->disable)); + + /* Stop processor */ + stop_processor(icom_port); + + dev_err(&icom_port->adapter->pci_dev->dev,"Port not operational\n"); + } + + if (new_page != NULL) + dma_free_coherent(&dev->dev, 4096, new_page, temp_pci); +} + +static int startup(struct icom_port *icom_port) +{ + unsigned long temp; + unsigned char cable_id, raw_cable_id; + unsigned long flags; + int port; + + trace(icom_port, "STARTUP", 0); + + if (!icom_port->dram) { + /* should NEVER be NULL */ + dev_err(&icom_port->adapter->pci_dev->dev, + "Unusable Port, port configuration missing\n"); + return -ENODEV; + } + + /* + * check Cable ID + */ + raw_cable_id = readb(&icom_port->dram->cable_id); + trace(icom_port, "CABLE_ID", raw_cable_id); + + /* Get cable ID into the lower 4 bits (standard form) */ + cable_id = (raw_cable_id & ICOM_CABLE_ID_MASK) >> 4; + + /* Check for valid Cable ID */ + if (!(raw_cable_id & ICOM_CABLE_ID_VALID) || + (cable_id != icom_port->cable_id)) { + + /* reload adapter code, pick up any potential changes in cable id */ + load_code(icom_port); + + /* still no sign of cable, error out */ + raw_cable_id = readb(&icom_port->dram->cable_id); + cable_id = (raw_cable_id & ICOM_CABLE_ID_MASK) >> 4; + if (!(raw_cable_id & ICOM_CABLE_ID_VALID) || + (icom_port->cable_id == NO_CABLE)) + return -EIO; + } + + /* + * Finally, clear and enable interrupts + */ + spin_lock_irqsave(&icom_lock, flags); + port = icom_port->port; + if (port >= ARRAY_SIZE(int_mask_tbl)) { + dev_err(&icom_port->adapter->pci_dev->dev, + "Invalid port assignment\n"); + goto unlock; + } + + if (port == 0 || port == 1) + int_mask_tbl[port].global_int_mask = &icom_port->global_reg->int_mask; + else + int_mask_tbl[port].global_int_mask = &icom_port->global_reg->int_mask_2; + + if (port == 0 || port == 2) + writew(0x00FF, icom_port->int_reg); + else + writew(0x3F00, icom_port->int_reg); + + temp = readl(int_mask_tbl[port].global_int_mask); + writel(temp & ~int_mask_tbl[port].processor_id, int_mask_tbl[port].global_int_mask); + + /* write flush */ + readl(int_mask_tbl[port].global_int_mask); + +unlock: + spin_unlock_irqrestore(&icom_lock, flags); + return 0; +} + +static void shutdown(struct icom_port *icom_port) +{ + unsigned long temp; + unsigned char cmdReg; + unsigned long flags; + int port; + + spin_lock_irqsave(&icom_lock, flags); + trace(icom_port, "SHUTDOWN", 0); + + /* + * disable all interrupts + */ + port = icom_port->port; + if (port >= ARRAY_SIZE(int_mask_tbl)) { + dev_err(&icom_port->adapter->pci_dev->dev, + "Invalid port assignment\n"); + goto unlock; + } + if (port == 0 || port == 1) + int_mask_tbl[port].global_int_mask = &icom_port->global_reg->int_mask; + else + int_mask_tbl[port].global_int_mask = &icom_port->global_reg->int_mask_2; + + temp = readl(int_mask_tbl[port].global_int_mask); + writel(temp | int_mask_tbl[port].processor_id, int_mask_tbl[port].global_int_mask); + + /* write flush */ + readl(int_mask_tbl[port].global_int_mask); + +unlock: + spin_unlock_irqrestore(&icom_lock, flags); + + /* + * disable break condition + */ + cmdReg = readb(&icom_port->dram->CmdReg); + if (cmdReg & CMD_SND_BREAK) { + writeb(cmdReg & ~CMD_SND_BREAK, &icom_port->dram->CmdReg); + } +} + +static int icom_write(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned long data_count; + unsigned char cmdReg; + unsigned long offset; + int temp_tail = port->state->xmit.tail; + + trace(icom_port, "WRITE", 0); + + if (le16_to_cpu(icom_port->statStg->xmit[0].flags) & + SA_FLAGS_READY_TO_XMIT) { + trace(icom_port, "WRITE_FULL", 0); + return 0; + } + + data_count = 0; + while ((port->state->xmit.head != temp_tail) && + (data_count <= XMIT_BUFF_SZ)) { + + icom_port->xmit_buf[data_count++] = + port->state->xmit.buf[temp_tail]; + + temp_tail++; + temp_tail &= (UART_XMIT_SIZE - 1); + } + + if (data_count) { + icom_port->statStg->xmit[0].flags = + cpu_to_le16(SA_FLAGS_READY_TO_XMIT); + icom_port->statStg->xmit[0].leLength = + cpu_to_le16(data_count); + offset = + (unsigned long) &icom_port->statStg->xmit[0] - + (unsigned long) icom_port->statStg; + *icom_port->xmitRestart = + cpu_to_le32(icom_port->statStg_pci + offset); + cmdReg = readb(&icom_port->dram->CmdReg); + writeb(cmdReg | CMD_XMIT_RCV_ENABLE, + &icom_port->dram->CmdReg); + writeb(START_XMIT, &icom_port->dram->StartXmitCmd); + trace(icom_port, "WRITE_START", data_count); + /* write flush */ + readb(&icom_port->dram->StartXmitCmd); + } + + return data_count; +} + +static inline void check_modem_status(struct icom_port *icom_port) +{ + static char old_status = 0; + char delta_status; + unsigned char status; + + spin_lock(&icom_port->uart_port.lock); + + /*modem input register */ + status = readb(&icom_port->dram->isr); + trace(icom_port, "CHECK_MODEM", status); + delta_status = status ^ old_status; + if (delta_status) { + if (delta_status & ICOM_RI) + icom_port->uart_port.icount.rng++; + if (delta_status & ICOM_DSR) + icom_port->uart_port.icount.dsr++; + if (delta_status & ICOM_DCD) + uart_handle_dcd_change(&icom_port->uart_port, + delta_status & ICOM_DCD); + if (delta_status & ICOM_CTS) + uart_handle_cts_change(&icom_port->uart_port, + delta_status & ICOM_CTS); + + wake_up_interruptible(&icom_port->uart_port.state-> + port.delta_msr_wait); + old_status = status; + } + spin_unlock(&icom_port->uart_port.lock); +} + +static void xmit_interrupt(u16 port_int_reg, struct icom_port *icom_port) +{ + u16 count, i; + + if (port_int_reg & (INT_XMIT_COMPLETED)) { + trace(icom_port, "XMIT_COMPLETE", 0); + + /* clear buffer in use bit */ + icom_port->statStg->xmit[0].flags &= + cpu_to_le16(~SA_FLAGS_READY_TO_XMIT); + + count = le16_to_cpu(icom_port->statStg->xmit[0].leLength); + icom_port->uart_port.icount.tx += count; + + for (i=0; i<count && + !uart_circ_empty(&icom_port->uart_port.state->xmit); i++) { + + icom_port->uart_port.state->xmit.tail++; + icom_port->uart_port.state->xmit.tail &= + (UART_XMIT_SIZE - 1); + } + + if (!icom_write(&icom_port->uart_port)) + /* activate write queue */ + uart_write_wakeup(&icom_port->uart_port); + } else + trace(icom_port, "XMIT_DISABLED", 0); +} + +static void recv_interrupt(u16 port_int_reg, struct icom_port *icom_port) +{ + short int count, rcv_buff; + struct tty_port *port = &icom_port->uart_port.state->port; + u16 status; + struct uart_icount *icount; + unsigned long offset; + unsigned char flag; + + trace(icom_port, "RCV_COMPLETE", 0); + rcv_buff = icom_port->next_rcv; + + status = le16_to_cpu(icom_port->statStg->rcv[rcv_buff].flags); + while (status & SA_FL_RCV_DONE) { + int first = -1; + + trace(icom_port, "FID_STATUS", status); + count = le16_to_cpu(icom_port->statStg->rcv[rcv_buff].leLength); + + trace(icom_port, "RCV_COUNT", count); + + trace(icom_port, "REAL_COUNT", count); + + offset = le32_to_cpu(icom_port->statStg->rcv[rcv_buff].leBuffer) - + icom_port->recv_buf_pci; + + /* Block copy all but the last byte as this may have status */ + if (count > 0) { + first = icom_port->recv_buf[offset]; + tty_insert_flip_string(port, icom_port->recv_buf + offset, count - 1); + } + + icount = &icom_port->uart_port.icount; + icount->rx += count; + + /* Break detect logic */ + if ((status & SA_FLAGS_FRAME_ERROR) + && first == 0) { + status &= ~SA_FLAGS_FRAME_ERROR; + status |= SA_FLAGS_BREAK_DET; + trace(icom_port, "BREAK_DET", 0); + } + + flag = TTY_NORMAL; + + if (status & + (SA_FLAGS_BREAK_DET | SA_FLAGS_PARITY_ERROR | + SA_FLAGS_FRAME_ERROR | SA_FLAGS_OVERRUN)) { + + if (status & SA_FLAGS_BREAK_DET) + icount->brk++; + if (status & SA_FLAGS_PARITY_ERROR) + icount->parity++; + if (status & SA_FLAGS_FRAME_ERROR) + icount->frame++; + if (status & SA_FLAGS_OVERRUN) + icount->overrun++; + + /* + * Now check to see if character should be + * ignored, and mask off conditions which + * should be ignored. + */ + if (status & icom_port->ignore_status_mask) { + trace(icom_port, "IGNORE_CHAR", 0); + goto ignore_char; + } + + status &= icom_port->read_status_mask; + + if (status & SA_FLAGS_BREAK_DET) { + flag = TTY_BREAK; + } else if (status & SA_FLAGS_PARITY_ERROR) { + trace(icom_port, "PARITY_ERROR", 0); + flag = TTY_PARITY; + } else if (status & SA_FLAGS_FRAME_ERROR) + flag = TTY_FRAME; + + } + + tty_insert_flip_char(port, *(icom_port->recv_buf + offset + count - 1), flag); + + if (status & SA_FLAGS_OVERRUN) + /* + * Overrun is special, since it's + * reported immediately, and doesn't + * affect the current character + */ + tty_insert_flip_char(port, 0, TTY_OVERRUN); +ignore_char: + icom_port->statStg->rcv[rcv_buff].flags = 0; + icom_port->statStg->rcv[rcv_buff].leLength = 0; + icom_port->statStg->rcv[rcv_buff].WorkingLength = + cpu_to_le16(RCV_BUFF_SZ); + + rcv_buff++; + if (rcv_buff == NUM_RBUFFS) + rcv_buff = 0; + + status = le16_to_cpu(icom_port->statStg->rcv[rcv_buff].flags); + } + icom_port->next_rcv = rcv_buff; + + tty_flip_buffer_push(port); +} + +static void process_interrupt(u16 port_int_reg, + struct icom_port *icom_port) +{ + + spin_lock(&icom_port->uart_port.lock); + trace(icom_port, "INTERRUPT", port_int_reg); + + if (port_int_reg & (INT_XMIT_COMPLETED | INT_XMIT_DISABLED)) + xmit_interrupt(port_int_reg, icom_port); + + if (port_int_reg & INT_RCV_COMPLETED) + recv_interrupt(port_int_reg, icom_port); + + spin_unlock(&icom_port->uart_port.lock); +} + +static irqreturn_t icom_interrupt(int irq, void *dev_id) +{ + void __iomem * int_reg; + u32 adapter_interrupts; + u16 port_int_reg; + struct icom_adapter *icom_adapter; + struct icom_port *icom_port; + + /* find icom_port for this interrupt */ + icom_adapter = (struct icom_adapter *) dev_id; + + if (icom_adapter->version == ADAPTER_V2) { + int_reg = icom_adapter->base_addr + 0x8024; + + adapter_interrupts = readl(int_reg); + + if (adapter_interrupts & 0x00003FFF) { + /* port 2 interrupt, NOTE: for all ADAPTER_V2, port 2 will be active */ + icom_port = &icom_adapter->port_info[2]; + port_int_reg = (u16) adapter_interrupts; + process_interrupt(port_int_reg, icom_port); + check_modem_status(icom_port); + } + if (adapter_interrupts & 0x3FFF0000) { + /* port 3 interrupt */ + icom_port = &icom_adapter->port_info[3]; + if (icom_port->status == ICOM_PORT_ACTIVE) { + port_int_reg = + (u16) (adapter_interrupts >> 16); + process_interrupt(port_int_reg, icom_port); + check_modem_status(icom_port); + } + } + + /* Clear out any pending interrupts */ + writel(adapter_interrupts, int_reg); + + int_reg = icom_adapter->base_addr + 0x8004; + } else { + int_reg = icom_adapter->base_addr + 0x4004; + } + + adapter_interrupts = readl(int_reg); + + if (adapter_interrupts & 0x00003FFF) { + /* port 0 interrupt, NOTE: for all adapters, port 0 will be active */ + icom_port = &icom_adapter->port_info[0]; + port_int_reg = (u16) adapter_interrupts; + process_interrupt(port_int_reg, icom_port); + check_modem_status(icom_port); + } + if (adapter_interrupts & 0x3FFF0000) { + /* port 1 interrupt */ + icom_port = &icom_adapter->port_info[1]; + if (icom_port->status == ICOM_PORT_ACTIVE) { + port_int_reg = (u16) (adapter_interrupts >> 16); + process_interrupt(port_int_reg, icom_port); + check_modem_status(icom_port); + } + } + + /* Clear out any pending interrupts */ + writel(adapter_interrupts, int_reg); + + /* flush the write */ + adapter_interrupts = readl(int_reg); + + return IRQ_HANDLED; +} + +/* + * ------------------------------------------------------------------ + * Begin serial-core API + * ------------------------------------------------------------------ + */ +static unsigned int icom_tx_empty(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + int ret; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + if (le16_to_cpu(icom_port->statStg->xmit[0].flags) & + SA_FLAGS_READY_TO_XMIT) + ret = TIOCSER_TEMT; + else + ret = 0; + + spin_unlock_irqrestore(&port->lock, flags); + return ret; +} + +static void icom_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char local_osr; + + trace(icom_port, "SET_MODEM", 0); + local_osr = readb(&icom_port->dram->osr); + + if (mctrl & TIOCM_RTS) { + trace(icom_port, "RAISE_RTS", 0); + local_osr |= ICOM_RTS; + } else { + trace(icom_port, "LOWER_RTS", 0); + local_osr &= ~ICOM_RTS; + } + + if (mctrl & TIOCM_DTR) { + trace(icom_port, "RAISE_DTR", 0); + local_osr |= ICOM_DTR; + } else { + trace(icom_port, "LOWER_DTR", 0); + local_osr &= ~ICOM_DTR; + } + + writeb(local_osr, &icom_port->dram->osr); +} + +static unsigned int icom_get_mctrl(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char status; + unsigned int result; + + trace(icom_port, "GET_MODEM", 0); + + status = readb(&icom_port->dram->isr); + + result = ((status & ICOM_DCD) ? TIOCM_CAR : 0) + | ((status & ICOM_RI) ? TIOCM_RNG : 0) + | ((status & ICOM_DSR) ? TIOCM_DSR : 0) + | ((status & ICOM_CTS) ? TIOCM_CTS : 0); + return result; +} + +static void icom_stop_tx(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char cmdReg; + + trace(icom_port, "STOP", 0); + cmdReg = readb(&icom_port->dram->CmdReg); + writeb(cmdReg | CMD_HOLD_XMIT, &icom_port->dram->CmdReg); +} + +static void icom_start_tx(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char cmdReg; + + trace(icom_port, "START", 0); + cmdReg = readb(&icom_port->dram->CmdReg); + if ((cmdReg & CMD_HOLD_XMIT) == CMD_HOLD_XMIT) + writeb(cmdReg & ~CMD_HOLD_XMIT, + &icom_port->dram->CmdReg); + + icom_write(port); +} + +static void icom_send_xchar(struct uart_port *port, char ch) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char xdata; + int index; + unsigned long flags; + + trace(icom_port, "SEND_XCHAR", ch); + + /* wait .1 sec to send char */ + for (index = 0; index < 10; index++) { + spin_lock_irqsave(&port->lock, flags); + xdata = readb(&icom_port->dram->xchar); + if (xdata == 0x00) { + trace(icom_port, "QUICK_WRITE", 0); + writeb(ch, &icom_port->dram->xchar); + + /* flush write operation */ + xdata = readb(&icom_port->dram->xchar); + spin_unlock_irqrestore(&port->lock, flags); + break; + } + spin_unlock_irqrestore(&port->lock, flags); + msleep(10); + } +} + +static void icom_stop_rx(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char cmdReg; + + cmdReg = readb(&icom_port->dram->CmdReg); + writeb(cmdReg & ~CMD_RCV_ENABLE, &icom_port->dram->CmdReg); +} + +static void icom_break(struct uart_port *port, int break_state) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char cmdReg; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + trace(icom_port, "BREAK", 0); + cmdReg = readb(&icom_port->dram->CmdReg); + if (break_state == -1) { + writeb(cmdReg | CMD_SND_BREAK, &icom_port->dram->CmdReg); + } else { + writeb(cmdReg & ~CMD_SND_BREAK, &icom_port->dram->CmdReg); + } + spin_unlock_irqrestore(&port->lock, flags); +} + +static int icom_open(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + int retval; + + kref_get(&icom_port->adapter->kref); + retval = startup(icom_port); + + if (retval) { + kref_put(&icom_port->adapter->kref, icom_kref_release); + trace(icom_port, "STARTUP_ERROR", 0); + return retval; + } + + return 0; +} + +static void icom_close(struct uart_port *port) +{ + struct icom_port *icom_port = to_icom_port(port); + unsigned char cmdReg; + + trace(icom_port, "CLOSE", 0); + + /* stop receiver */ + cmdReg = readb(&icom_port->dram->CmdReg); + writeb(cmdReg & ~CMD_RCV_ENABLE, &icom_port->dram->CmdReg); + + shutdown(icom_port); + + kref_put(&icom_port->adapter->kref, icom_kref_release); +} + +static void icom_set_termios(struct uart_port *port, struct ktermios *termios, + const struct ktermios *old_termios) +{ + struct icom_port *icom_port = to_icom_port(port); + int baud; + unsigned cflag, iflag; + char new_config2; + char new_config3 = 0; + char tmp_byte; + int index; + int rcv_buff, xmit_buff; + unsigned long offset; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + trace(icom_port, "CHANGE_SPEED", 0); + + cflag = termios->c_cflag; + iflag = termios->c_iflag; + + new_config2 = ICOM_ACFG_DRIVE1; + + /* byte size and parity */ + switch (cflag & CSIZE) { + case CS5: /* 5 bits/char */ + new_config2 |= ICOM_ACFG_5BPC; + break; + case CS6: /* 6 bits/char */ + new_config2 |= ICOM_ACFG_6BPC; + break; + case CS7: /* 7 bits/char */ + new_config2 |= ICOM_ACFG_7BPC; + break; + case CS8: /* 8 bits/char */ + new_config2 |= ICOM_ACFG_8BPC; + break; + default: + break; + } + if (cflag & CSTOPB) { + /* 2 stop bits */ + new_config2 |= ICOM_ACFG_2STOP_BIT; + } + if (cflag & PARENB) { + /* parity bit enabled */ + new_config2 |= ICOM_ACFG_PARITY_ENAB; + trace(icom_port, "PARENB", 0); + } + if (cflag & PARODD) { + /* odd parity */ + new_config2 |= ICOM_ACFG_PARITY_ODD; + trace(icom_port, "PARODD", 0); + } + + /* Determine divisor based on baud rate */ + baud = uart_get_baud_rate(port, termios, old_termios, + icom_acfg_baud[0], + icom_acfg_baud[BAUD_TABLE_LIMIT]); + if (!baud) + baud = 9600; /* B0 transition handled in rs_set_termios */ + + for (index = 0; index < BAUD_TABLE_LIMIT; index++) { + if (icom_acfg_baud[index] == baud) { + new_config3 = index; + break; + } + } + + uart_update_timeout(port, cflag, baud); + + /* CTS flow control flag and modem status interrupts */ + tmp_byte = readb(&(icom_port->dram->HDLCConfigReg)); + if (cflag & CRTSCTS) + tmp_byte |= HDLC_HDW_FLOW; + else + tmp_byte &= ~HDLC_HDW_FLOW; + writeb(tmp_byte, &(icom_port->dram->HDLCConfigReg)); + + /* + * Set up parity check flag + */ + icom_port->read_status_mask = SA_FLAGS_OVERRUN | SA_FL_RCV_DONE; + if (iflag & INPCK) + icom_port->read_status_mask |= + SA_FLAGS_FRAME_ERROR | SA_FLAGS_PARITY_ERROR; + + if ((iflag & BRKINT) || (iflag & PARMRK)) + icom_port->read_status_mask |= SA_FLAGS_BREAK_DET; + + /* + * Characters to ignore + */ + icom_port->ignore_status_mask = 0; + if (iflag & IGNPAR) + icom_port->ignore_status_mask |= + SA_FLAGS_PARITY_ERROR | SA_FLAGS_FRAME_ERROR; + if (iflag & IGNBRK) { + icom_port->ignore_status_mask |= SA_FLAGS_BREAK_DET; + /* + * If we're ignore parity and break indicators, ignore + * overruns too. (For real raw support). + */ + if (iflag & IGNPAR) + icom_port->ignore_status_mask |= SA_FLAGS_OVERRUN; + } + + /* + * !!! ignore all characters if CREAD is not set + */ + if ((cflag & CREAD) == 0) + icom_port->ignore_status_mask |= SA_FL_RCV_DONE; + + /* Turn off Receiver to prepare for reset */ + writeb(CMD_RCV_DISABLE, &icom_port->dram->CmdReg); + + for (index = 0; index < 10; index++) { + if (readb(&icom_port->dram->PrevCmdReg) == 0x00) { + break; + } + } + + /* clear all current buffers of data */ + for (rcv_buff = 0; rcv_buff < NUM_RBUFFS; rcv_buff++) { + icom_port->statStg->rcv[rcv_buff].flags = 0; + icom_port->statStg->rcv[rcv_buff].leLength = 0; + icom_port->statStg->rcv[rcv_buff].WorkingLength = + cpu_to_le16(RCV_BUFF_SZ); + } + + for (xmit_buff = 0; xmit_buff < NUM_XBUFFS; xmit_buff++) { + icom_port->statStg->xmit[xmit_buff].flags = 0; + } + + /* activate changes and start xmit and receiver here */ + /* Enable the receiver */ + writeb(new_config3, &(icom_port->dram->async_config3)); + writeb(new_config2, &(icom_port->dram->async_config2)); + tmp_byte = readb(&(icom_port->dram->HDLCConfigReg)); + tmp_byte |= HDLC_PPP_PURE_ASYNC | HDLC_FF_FILL; + writeb(tmp_byte, &(icom_port->dram->HDLCConfigReg)); + writeb(0x04, &(icom_port->dram->FlagFillIdleTimer)); /* 0.5 seconds */ + writeb(0xFF, &(icom_port->dram->ier)); /* enable modem signal interrupts */ + + /* reset processor */ + writeb(CMD_RESTART, &icom_port->dram->CmdReg); + + for (index = 0; index < 10; index++) { + if (readb(&icom_port->dram->CmdReg) == 0x00) { + break; + } + } + + /* Enable Transmitter and Receiver */ + offset = + (unsigned long) &icom_port->statStg->rcv[0] - + (unsigned long) icom_port->statStg; + writel(icom_port->statStg_pci + offset, + &icom_port->dram->RcvStatusAddr); + icom_port->next_rcv = 0; + *icom_port->xmitRestart = 0; + writel(icom_port->xmitRestart_pci, + &icom_port->dram->XmitStatusAddr); + trace(icom_port, "XR_ENAB", 0); + writeb(CMD_XMIT_RCV_ENABLE, &icom_port->dram->CmdReg); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *icom_type(struct uart_port *port) +{ + return "icom"; +} + +static void icom_config_port(struct uart_port *port, int flags) +{ + port->type = PORT_ICOM; +} + +static const struct uart_ops icom_ops = { + .tx_empty = icom_tx_empty, + .set_mctrl = icom_set_mctrl, + .get_mctrl = icom_get_mctrl, + .stop_tx = icom_stop_tx, + .start_tx = icom_start_tx, + .send_xchar = icom_send_xchar, + .stop_rx = icom_stop_rx, + .break_ctl = icom_break, + .startup = icom_open, + .shutdown = icom_close, + .set_termios = icom_set_termios, + .type = icom_type, + .config_port = icom_config_port, +}; + +#define ICOM_CONSOLE NULL + +static struct uart_driver icom_uart_driver = { + .owner = THIS_MODULE, + .driver_name = ICOM_DRIVER_NAME, + .dev_name = "ttyA", + .major = ICOM_MAJOR, + .minor = ICOM_MINOR_START, + .nr = NR_PORTS, + .cons = ICOM_CONSOLE, +}; + +static int icom_init_ports(struct icom_adapter *icom_adapter) +{ + u32 subsystem_id = icom_adapter->subsystem_id; + int i; + struct icom_port *icom_port; + + if (icom_adapter->version == ADAPTER_V1) { + icom_adapter->numb_ports = 2; + + for (i = 0; i < 2; i++) { + icom_port = &icom_adapter->port_info[i]; + icom_port->port = i; + icom_port->status = ICOM_PORT_ACTIVE; + } + } else { + if (subsystem_id == PCI_DEVICE_ID_IBM_ICOM_FOUR_PORT_MODEL) { + icom_adapter->numb_ports = 4; + + for (i = 0; i < 4; i++) { + icom_port = &icom_adapter->port_info[i]; + + icom_port->port = i; + icom_port->status = ICOM_PORT_ACTIVE; + } + } else { + icom_adapter->numb_ports = 4; + + icom_adapter->port_info[0].port = 0; + icom_adapter->port_info[0].status = ICOM_PORT_ACTIVE; + icom_adapter->port_info[1].status = ICOM_PORT_OFF; + icom_adapter->port_info[2].port = 2; + icom_adapter->port_info[2].status = ICOM_PORT_ACTIVE; + icom_adapter->port_info[3].status = ICOM_PORT_OFF; + } + } + + return 0; +} + +static void icom_port_active(struct icom_port *icom_port, struct icom_adapter *icom_adapter, int port_num) +{ + if (icom_adapter->version == ADAPTER_V1) { + icom_port->global_reg = icom_adapter->base_addr + 0x4000; + icom_port->int_reg = icom_adapter->base_addr + + 0x4004 + 2 - 2 * port_num; + } else { + icom_port->global_reg = icom_adapter->base_addr + 0x8000; + if (icom_port->port < 2) + icom_port->int_reg = icom_adapter->base_addr + + 0x8004 + 2 - 2 * icom_port->port; + else + icom_port->int_reg = icom_adapter->base_addr + + 0x8024 + 2 - 2 * (icom_port->port - 2); + } +} +static int icom_load_ports(struct icom_adapter *icom_adapter) +{ + struct icom_port *icom_port; + int port_num; + + for (port_num = 0; port_num < icom_adapter->numb_ports; port_num++) { + + icom_port = &icom_adapter->port_info[port_num]; + + if (icom_port->status == ICOM_PORT_ACTIVE) { + icom_port_active(icom_port, icom_adapter, port_num); + icom_port->dram = icom_adapter->base_addr + + 0x2000 * icom_port->port; + + icom_port->adapter = icom_adapter; + + /* get port memory */ + if (get_port_memory(icom_port) != 0) { + dev_err(&icom_port->adapter->pci_dev->dev, + "Memory allocation for port FAILED\n"); + } + } + } + return 0; +} + +static int icom_alloc_adapter(struct icom_adapter + **icom_adapter_ref) +{ + int adapter_count = 0; + struct icom_adapter *icom_adapter; + struct icom_adapter *cur_adapter_entry; + + icom_adapter = kzalloc(sizeof(struct icom_adapter), GFP_KERNEL); + + if (!icom_adapter) { + return -ENOMEM; + } + + list_for_each_entry(cur_adapter_entry, &icom_adapter_head, + icom_adapter_entry) { + if (cur_adapter_entry->index != adapter_count) { + break; + } + adapter_count++; + } + + icom_adapter->index = adapter_count; + list_add_tail(&icom_adapter->icom_adapter_entry, + &cur_adapter_entry->icom_adapter_entry); + + *icom_adapter_ref = icom_adapter; + return 0; +} + +static void icom_free_adapter(struct icom_adapter *icom_adapter) +{ + list_del(&icom_adapter->icom_adapter_entry); + kfree(icom_adapter); +} + +static void icom_kref_release(struct kref *kref) +{ + struct icom_adapter *icom_adapter = container_of(kref, + struct icom_adapter, kref); + struct icom_port *icom_port; + int index; + + for (index = 0; index < icom_adapter->numb_ports; index++) { + icom_port = &icom_adapter->port_info[index]; + + if (icom_port->status == ICOM_PORT_ACTIVE) { + dev_info(&icom_adapter->pci_dev->dev, + "Device removed\n"); + + uart_remove_one_port(&icom_uart_driver, + &icom_port->uart_port); + + /* be sure that DTR and RTS are dropped */ + writeb(0x00, &icom_port->dram->osr); + + /* Wait 0.1 Sec for simple Init to complete */ + msleep(100); + + /* Stop proccessor */ + stop_processor(icom_port); + + free_port_memory(icom_port); + } + } + + free_irq(icom_adapter->pci_dev->irq, (void *) icom_adapter); + iounmap(icom_adapter->base_addr); + pci_release_regions(icom_adapter->pci_dev); + icom_free_adapter(icom_adapter); +} + +static int icom_probe(struct pci_dev *dev, + const struct pci_device_id *ent) +{ + int index; + unsigned int command_reg; + int retval; + struct icom_adapter *icom_adapter; + struct icom_port *icom_port; + + retval = pci_enable_device(dev); + if (retval) { + dev_err(&dev->dev, "Device enable FAILED\n"); + return retval; + } + + retval = pci_request_regions(dev, "icom"); + if (retval) { + dev_err(&dev->dev, "pci_request_regions FAILED\n"); + pci_disable_device(dev); + return retval; + } + + pci_set_master(dev); + + retval = pci_read_config_dword(dev, PCI_COMMAND, &command_reg); + if (retval) { + dev_err(&dev->dev, "PCI Config read FAILED\n"); + goto probe_exit0; + } + + pci_write_config_dword(dev, PCI_COMMAND, + command_reg | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER + | PCI_COMMAND_PARITY | PCI_COMMAND_SERR); + + if (ent->driver_data == ADAPTER_V1) { + pci_write_config_dword(dev, 0x44, 0x8300830A); + } else { + pci_write_config_dword(dev, 0x44, 0x42004200); + pci_write_config_dword(dev, 0x48, 0x42004200); + } + + + retval = icom_alloc_adapter(&icom_adapter); + if (retval) { + dev_err(&dev->dev, "icom_alloc_adapter FAILED\n"); + retval = -EIO; + goto probe_exit0; + } + + icom_adapter->base_addr_pci = pci_resource_start(dev, 0); + icom_adapter->pci_dev = dev; + icom_adapter->version = ent->driver_data; + icom_adapter->subsystem_id = ent->subdevice; + + + retval = icom_init_ports(icom_adapter); + if (retval) { + dev_err(&dev->dev, "Port configuration failed\n"); + goto probe_exit1; + } + + icom_adapter->base_addr = pci_ioremap_bar(dev, 0); + + if (!icom_adapter->base_addr) { + retval = -ENOMEM; + goto probe_exit1; + } + + /* save off irq and request irq line */ + retval = request_irq(dev->irq, icom_interrupt, IRQF_SHARED, ICOM_DRIVER_NAME, (void *)icom_adapter); + if (retval) { + goto probe_exit2; + } + + retval = icom_load_ports(icom_adapter); + + for (index = 0; index < icom_adapter->numb_ports; index++) { + icom_port = &icom_adapter->port_info[index]; + + if (icom_port->status == ICOM_PORT_ACTIVE) { + icom_port->uart_port.irq = icom_port->adapter->pci_dev->irq; + icom_port->uart_port.type = PORT_ICOM; + icom_port->uart_port.iotype = UPIO_MEM; + icom_port->uart_port.membase = + (unsigned char __iomem *)icom_adapter->base_addr_pci; + icom_port->uart_port.fifosize = 16; + icom_port->uart_port.ops = &icom_ops; + icom_port->uart_port.line = + icom_port->port + icom_adapter->index * 4; + if (uart_add_one_port (&icom_uart_driver, &icom_port->uart_port)) { + icom_port->status = ICOM_PORT_OFF; + dev_err(&dev->dev, "Device add failed\n"); + } else + dev_info(&dev->dev, "Device added\n"); + } + } + + kref_init(&icom_adapter->kref); + return 0; + +probe_exit2: + iounmap(icom_adapter->base_addr); +probe_exit1: + icom_free_adapter(icom_adapter); + +probe_exit0: + pci_release_regions(dev); + pci_disable_device(dev); + + return retval; +} + +static void icom_remove(struct pci_dev *dev) +{ + struct icom_adapter *icom_adapter; + + list_for_each_entry(icom_adapter, &icom_adapter_head, + icom_adapter_entry) { + if (icom_adapter->pci_dev == dev) { + kref_put(&icom_adapter->kref, icom_kref_release); + return; + } + } + + dev_err(&dev->dev, "Unable to find device to remove\n"); +} + +static struct pci_driver icom_pci_driver = { + .name = ICOM_DRIVER_NAME, + .id_table = icom_pci_table, + .probe = icom_probe, + .remove = icom_remove, +}; + +static int __init icom_init(void) +{ + int ret; + + ret = uart_register_driver(&icom_uart_driver); + if (ret) + return ret; + + ret = pci_register_driver(&icom_pci_driver); + + if (ret < 0) + uart_unregister_driver(&icom_uart_driver); + + return ret; +} + +static void __exit icom_exit(void) +{ + pci_unregister_driver(&icom_pci_driver); + uart_unregister_driver(&icom_uart_driver); +} + +module_init(icom_init); +module_exit(icom_exit); + +MODULE_AUTHOR("Michael Anderson <mjanders@us.ibm.com>"); +MODULE_DESCRIPTION("IBM iSeries Serial IOA driver"); +MODULE_LICENSE("GPL"); +MODULE_FIRMWARE("icom_call_setup.bin"); +MODULE_FIRMWARE("icom_res_dce.bin"); +MODULE_FIRMWARE("icom_asc.bin"); |