summaryrefslogtreecommitdiffstats
path: root/sound/pci/asihpi/hpi6000.c
diff options
context:
space:
mode:
Diffstat (limited to 'sound/pci/asihpi/hpi6000.c')
-rw-r--r--sound/pci/asihpi/hpi6000.c1801
1 files changed, 1801 insertions, 0 deletions
diff --git a/sound/pci/asihpi/hpi6000.c b/sound/pci/asihpi/hpi6000.c
new file mode 100644
index 000000000..88d902997
--- /dev/null
+++ b/sound/pci/asihpi/hpi6000.c
@@ -0,0 +1,1801 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/******************************************************************************
+
+ AudioScience HPI driver
+ Copyright (C) 1997-2011 AudioScience Inc. <support@audioscience.com>
+
+
+ Hardware Programming Interface (HPI) for AudioScience ASI6200 series adapters.
+ These PCI bus adapters are based on the TI C6711 DSP.
+
+ Exported functions:
+ void HPI_6000(struct hpi_message *phm, struct hpi_response *phr)
+
+ #defines
+ HIDE_PCI_ASSERTS to show the PCI asserts
+ PROFILE_DSP2 get profile data from DSP2 if present (instead of DSP 1)
+
+(C) Copyright AudioScience Inc. 1998-2003
+*******************************************************************************/
+#define SOURCEFILE_NAME "hpi6000.c"
+
+#include "hpi_internal.h"
+#include "hpimsginit.h"
+#include "hpidebug.h"
+#include "hpi6000.h"
+#include "hpidspcd.h"
+#include "hpicmn.h"
+
+#define HPI_HIF_BASE (0x00000200) /* start of C67xx internal RAM */
+#define HPI_HIF_ADDR(member) \
+ (HPI_HIF_BASE + offsetof(struct hpi_hif_6000, member))
+#define HPI_HIF_ERROR_MASK 0x4000
+
+/* HPI6000 specific error codes */
+#define HPI6000_ERROR_BASE 900 /* not actually used anywhere */
+
+/* operational/messaging errors */
+#define HPI6000_ERROR_MSG_RESP_IDLE_TIMEOUT 901
+#define HPI6000_ERROR_RESP_GET_LEN 902
+#define HPI6000_ERROR_MSG_RESP_GET_RESP_ACK 903
+#define HPI6000_ERROR_MSG_GET_ADR 904
+#define HPI6000_ERROR_RESP_GET_ADR 905
+#define HPI6000_ERROR_MSG_RESP_BLOCKWRITE32 906
+#define HPI6000_ERROR_MSG_RESP_BLOCKREAD32 907
+
+#define HPI6000_ERROR_CONTROL_CACHE_PARAMS 909
+
+#define HPI6000_ERROR_SEND_DATA_IDLE_TIMEOUT 911
+#define HPI6000_ERROR_SEND_DATA_ACK 912
+#define HPI6000_ERROR_SEND_DATA_ADR 913
+#define HPI6000_ERROR_SEND_DATA_TIMEOUT 914
+#define HPI6000_ERROR_SEND_DATA_CMD 915
+#define HPI6000_ERROR_SEND_DATA_WRITE 916
+#define HPI6000_ERROR_SEND_DATA_IDLECMD 917
+
+#define HPI6000_ERROR_GET_DATA_IDLE_TIMEOUT 921
+#define HPI6000_ERROR_GET_DATA_ACK 922
+#define HPI6000_ERROR_GET_DATA_CMD 923
+#define HPI6000_ERROR_GET_DATA_READ 924
+#define HPI6000_ERROR_GET_DATA_IDLECMD 925
+
+#define HPI6000_ERROR_CONTROL_CACHE_ADDRLEN 951
+#define HPI6000_ERROR_CONTROL_CACHE_READ 952
+#define HPI6000_ERROR_CONTROL_CACHE_FLUSH 953
+
+#define HPI6000_ERROR_MSG_RESP_GETRESPCMD 961
+#define HPI6000_ERROR_MSG_RESP_IDLECMD 962
+
+/* Initialisation/bootload errors */
+#define HPI6000_ERROR_UNHANDLED_SUBSYS_ID 930
+
+/* can't access PCI2040 */
+#define HPI6000_ERROR_INIT_PCI2040 931
+/* can't access DSP HPI i/f */
+#define HPI6000_ERROR_INIT_DSPHPI 932
+/* can't access internal DSP memory */
+#define HPI6000_ERROR_INIT_DSPINTMEM 933
+/* can't access SDRAM - test#1 */
+#define HPI6000_ERROR_INIT_SDRAM1 934
+/* can't access SDRAM - test#2 */
+#define HPI6000_ERROR_INIT_SDRAM2 935
+
+#define HPI6000_ERROR_INIT_VERIFY 938
+
+#define HPI6000_ERROR_INIT_NOACK 939
+
+#define HPI6000_ERROR_INIT_PLDTEST1 941
+#define HPI6000_ERROR_INIT_PLDTEST2 942
+
+/* local defines */
+
+#define HIDE_PCI_ASSERTS
+#define PROFILE_DSP2
+
+/* for PCI2040 i/f chip */
+/* HPI CSR registers */
+/* word offsets from CSR base */
+/* use when io addresses defined as u32 * */
+
+#define INTERRUPT_EVENT_SET 0
+#define INTERRUPT_EVENT_CLEAR 1
+#define INTERRUPT_MASK_SET 2
+#define INTERRUPT_MASK_CLEAR 3
+#define HPI_ERROR_REPORT 4
+#define HPI_RESET 5
+#define HPI_DATA_WIDTH 6
+
+#define MAX_DSPS 2
+/* HPI registers, spaced 8K bytes = 2K words apart */
+#define DSP_SPACING 0x800
+
+#define CONTROL 0x0000
+#define ADDRESS 0x0200
+#define DATA_AUTOINC 0x0400
+#define DATA 0x0600
+
+#define TIMEOUT 500000
+
+struct dsp_obj {
+ __iomem u32 *prHPI_control;
+ __iomem u32 *prHPI_address;
+ __iomem u32 *prHPI_data;
+ __iomem u32 *prHPI_data_auto_inc;
+ char c_dsp_rev; /*A, B */
+ u32 control_cache_address_on_dsp;
+ u32 control_cache_length_on_dsp;
+ struct hpi_adapter_obj *pa_parent_adapter;
+};
+
+struct hpi_hw_obj {
+ __iomem u32 *dw2040_HPICSR;
+ __iomem u32 *dw2040_HPIDSP;
+
+ u16 num_dsp;
+ struct dsp_obj ado[MAX_DSPS];
+
+ u32 message_buffer_address_on_dsp;
+ u32 response_buffer_address_on_dsp;
+ u32 pCI2040HPI_error_count;
+
+ struct hpi_control_cache_single control_cache[HPI_NMIXER_CONTROLS];
+ struct hpi_control_cache *p_cache;
+};
+
+static u16 hpi6000_dsp_block_write32(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 hpi_address, u32 *source, u32 count);
+static u16 hpi6000_dsp_block_read32(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 hpi_address, u32 *dest, u32 count);
+
+static short hpi6000_adapter_boot_load_dsp(struct hpi_adapter_obj *pao,
+ u32 *pos_error_code);
+static short hpi6000_check_PCI2040_error_flag(struct hpi_adapter_obj *pao,
+ u16 read_or_write);
+#define H6READ 1
+#define H6WRITE 0
+
+static short hpi6000_update_control_cache(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm);
+static short hpi6000_message_response_sequence(struct hpi_adapter_obj *pao,
+ u16 dsp_index, struct hpi_message *phm, struct hpi_response *phr);
+
+static void hw_message(struct hpi_adapter_obj *pao, struct hpi_message *phm,
+ struct hpi_response *phr);
+
+static short hpi6000_wait_dsp_ack(struct hpi_adapter_obj *pao, u16 dsp_index,
+ u32 ack_value);
+
+static short hpi6000_send_host_command(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 host_cmd);
+
+static void hpi6000_send_dsp_interrupt(struct dsp_obj *pdo);
+
+static short hpi6000_send_data(struct hpi_adapter_obj *pao, u16 dsp_index,
+ struct hpi_message *phm, struct hpi_response *phr);
+
+static short hpi6000_get_data(struct hpi_adapter_obj *pao, u16 dsp_index,
+ struct hpi_message *phm, struct hpi_response *phr);
+
+static void hpi_write_word(struct dsp_obj *pdo, u32 address, u32 data);
+
+static u32 hpi_read_word(struct dsp_obj *pdo, u32 address);
+
+static void hpi_write_block(struct dsp_obj *pdo, u32 address, u32 *pdata,
+ u32 length);
+
+static void hpi_read_block(struct dsp_obj *pdo, u32 address, u32 *pdata,
+ u32 length);
+
+static void subsys_create_adapter(struct hpi_message *phm,
+ struct hpi_response *phr);
+
+static void adapter_delete(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr);
+
+static void adapter_get_asserts(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr);
+
+static short create_adapter_obj(struct hpi_adapter_obj *pao,
+ u32 *pos_error_code);
+
+static void delete_adapter_obj(struct hpi_adapter_obj *pao);
+
+/* local globals */
+
+static u16 gw_pci_read_asserts; /* used to count PCI2040 errors */
+static u16 gw_pci_write_asserts; /* used to count PCI2040 errors */
+
+static void subsys_message(struct hpi_message *phm, struct hpi_response *phr)
+{
+ switch (phm->function) {
+ case HPI_SUBSYS_CREATE_ADAPTER:
+ subsys_create_adapter(phm, phr);
+ break;
+ default:
+ phr->error = HPI_ERROR_INVALID_FUNC;
+ break;
+ }
+}
+
+static void control_message(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+
+ switch (phm->function) {
+ case HPI_CONTROL_GET_STATE:
+ if (pao->has_control_cache) {
+ u16 err;
+ err = hpi6000_update_control_cache(pao, phm);
+
+ if (err) {
+ if (err >= HPI_ERROR_BACKEND_BASE) {
+ phr->error =
+ HPI_ERROR_CONTROL_CACHING;
+ phr->specific_error = err;
+ } else {
+ phr->error = err;
+ }
+ break;
+ }
+
+ if (hpi_check_control_cache(phw->p_cache, phm, phr))
+ break;
+ }
+ hw_message(pao, phm, phr);
+ break;
+ case HPI_CONTROL_SET_STATE:
+ hw_message(pao, phm, phr);
+ hpi_cmn_control_cache_sync_to_msg(phw->p_cache, phm, phr);
+ break;
+
+ case HPI_CONTROL_GET_INFO:
+ default:
+ hw_message(pao, phm, phr);
+ break;
+ }
+}
+
+static void adapter_message(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ switch (phm->function) {
+ case HPI_ADAPTER_GET_ASSERT:
+ adapter_get_asserts(pao, phm, phr);
+ break;
+
+ case HPI_ADAPTER_DELETE:
+ adapter_delete(pao, phm, phr);
+ break;
+
+ default:
+ hw_message(pao, phm, phr);
+ break;
+ }
+}
+
+static void outstream_message(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ switch (phm->function) {
+ case HPI_OSTREAM_HOSTBUFFER_ALLOC:
+ case HPI_OSTREAM_HOSTBUFFER_FREE:
+ /* Don't let these messages go to the HW function because
+ * they're called without locking the spinlock.
+ * For the HPI6000 adapters the HW would return
+ * HPI_ERROR_INVALID_FUNC anyway.
+ */
+ phr->error = HPI_ERROR_INVALID_FUNC;
+ break;
+ default:
+ hw_message(pao, phm, phr);
+ return;
+ }
+}
+
+static void instream_message(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+
+ switch (phm->function) {
+ case HPI_ISTREAM_HOSTBUFFER_ALLOC:
+ case HPI_ISTREAM_HOSTBUFFER_FREE:
+ /* Don't let these messages go to the HW function because
+ * they're called without locking the spinlock.
+ * For the HPI6000 adapters the HW would return
+ * HPI_ERROR_INVALID_FUNC anyway.
+ */
+ phr->error = HPI_ERROR_INVALID_FUNC;
+ break;
+ default:
+ hw_message(pao, phm, phr);
+ return;
+ }
+}
+
+/************************************************************************/
+/** HPI_6000()
+ * Entry point from HPIMAN
+ * All calls to the HPI start here
+ */
+void HPI_6000(struct hpi_message *phm, struct hpi_response *phr)
+{
+ struct hpi_adapter_obj *pao = NULL;
+
+ if (phm->object != HPI_OBJ_SUBSYSTEM) {
+ pao = hpi_find_adapter(phm->adapter_index);
+ if (!pao) {
+ hpi_init_response(phr, phm->object, phm->function,
+ HPI_ERROR_BAD_ADAPTER_NUMBER);
+ HPI_DEBUG_LOG(DEBUG, "invalid adapter index: %d \n",
+ phm->adapter_index);
+ return;
+ }
+
+ /* Don't even try to communicate with crashed DSP */
+ if (pao->dsp_crashed >= 10) {
+ hpi_init_response(phr, phm->object, phm->function,
+ HPI_ERROR_DSP_HARDWARE);
+ HPI_DEBUG_LOG(DEBUG, "adapter %d dsp crashed\n",
+ phm->adapter_index);
+ return;
+ }
+ }
+ /* Init default response including the size field */
+ if (phm->function != HPI_SUBSYS_CREATE_ADAPTER)
+ hpi_init_response(phr, phm->object, phm->function,
+ HPI_ERROR_PROCESSING_MESSAGE);
+
+ switch (phm->type) {
+ case HPI_TYPE_REQUEST:
+ switch (phm->object) {
+ case HPI_OBJ_SUBSYSTEM:
+ subsys_message(phm, phr);
+ break;
+
+ case HPI_OBJ_ADAPTER:
+ phr->size =
+ sizeof(struct hpi_response_header) +
+ sizeof(struct hpi_adapter_res);
+ adapter_message(pao, phm, phr);
+ break;
+
+ case HPI_OBJ_CONTROL:
+ control_message(pao, phm, phr);
+ break;
+
+ case HPI_OBJ_OSTREAM:
+ outstream_message(pao, phm, phr);
+ break;
+
+ case HPI_OBJ_ISTREAM:
+ instream_message(pao, phm, phr);
+ break;
+
+ default:
+ hw_message(pao, phm, phr);
+ break;
+ }
+ break;
+
+ default:
+ phr->error = HPI_ERROR_INVALID_TYPE;
+ break;
+ }
+}
+
+/************************************************************************/
+/* SUBSYSTEM */
+
+/* create an adapter object and initialise it based on resource information
+ * passed in the message
+ * NOTE - you cannot use this function AND the FindAdapters function at the
+ * same time, the application must use only one of them to get the adapters
+ */
+static void subsys_create_adapter(struct hpi_message *phm,
+ struct hpi_response *phr)
+{
+ /* create temp adapter obj, because we don't know what index yet */
+ struct hpi_adapter_obj ao;
+ struct hpi_adapter_obj *pao;
+ u32 os_error_code;
+ u16 err = 0;
+ u32 dsp_index = 0;
+
+ HPI_DEBUG_LOG(VERBOSE, "subsys_create_adapter\n");
+
+ memset(&ao, 0, sizeof(ao));
+
+ ao.priv = kzalloc(sizeof(struct hpi_hw_obj), GFP_KERNEL);
+ if (!ao.priv) {
+ HPI_DEBUG_LOG(ERROR, "can't get mem for adapter object\n");
+ phr->error = HPI_ERROR_MEMORY_ALLOC;
+ return;
+ }
+
+ /* create the adapter object based on the resource information */
+ ao.pci = *phm->u.s.resource.r.pci;
+
+ err = create_adapter_obj(&ao, &os_error_code);
+ if (err) {
+ delete_adapter_obj(&ao);
+ if (err >= HPI_ERROR_BACKEND_BASE) {
+ phr->error = HPI_ERROR_DSP_BOOTLOAD;
+ phr->specific_error = err;
+ } else {
+ phr->error = err;
+ }
+
+ phr->u.s.data = os_error_code;
+ return;
+ }
+ /* need to update paParentAdapter */
+ pao = hpi_find_adapter(ao.index);
+ if (!pao) {
+ /* We just added this adapter, why can't we find it!? */
+ HPI_DEBUG_LOG(ERROR, "lost adapter after boot\n");
+ phr->error = HPI_ERROR_BAD_ADAPTER;
+ return;
+ }
+
+ for (dsp_index = 0; dsp_index < MAX_DSPS; dsp_index++) {
+ struct hpi_hw_obj *phw = pao->priv;
+ phw->ado[dsp_index].pa_parent_adapter = pao;
+ }
+
+ phr->u.s.adapter_type = ao.type;
+ phr->u.s.adapter_index = ao.index;
+ phr->error = 0;
+}
+
+static void adapter_delete(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ delete_adapter_obj(pao);
+ hpi_delete_adapter(pao);
+ phr->error = 0;
+}
+
+/* this routine is called from SubSysFindAdapter and SubSysCreateAdapter */
+static short create_adapter_obj(struct hpi_adapter_obj *pao,
+ u32 *pos_error_code)
+{
+ short boot_error = 0;
+ u32 dsp_index = 0;
+ u32 control_cache_size = 0;
+ u32 control_cache_count = 0;
+ struct hpi_hw_obj *phw = pao->priv;
+
+ /* The PCI2040 has the following address map */
+ /* BAR0 - 4K = HPI control and status registers on PCI2040 (HPI CSR) */
+ /* BAR1 - 32K = HPI registers on DSP */
+ phw->dw2040_HPICSR = pao->pci.ap_mem_base[0];
+ phw->dw2040_HPIDSP = pao->pci.ap_mem_base[1];
+ HPI_DEBUG_LOG(VERBOSE, "csr %p, dsp %p\n", phw->dw2040_HPICSR,
+ phw->dw2040_HPIDSP);
+
+ /* set addresses for the possible DSP HPI interfaces */
+ for (dsp_index = 0; dsp_index < MAX_DSPS; dsp_index++) {
+ phw->ado[dsp_index].prHPI_control =
+ phw->dw2040_HPIDSP + (CONTROL +
+ DSP_SPACING * dsp_index);
+
+ phw->ado[dsp_index].prHPI_address =
+ phw->dw2040_HPIDSP + (ADDRESS +
+ DSP_SPACING * dsp_index);
+ phw->ado[dsp_index].prHPI_data =
+ phw->dw2040_HPIDSP + (DATA + DSP_SPACING * dsp_index);
+
+ phw->ado[dsp_index].prHPI_data_auto_inc =
+ phw->dw2040_HPIDSP + (DATA_AUTOINC +
+ DSP_SPACING * dsp_index);
+
+ HPI_DEBUG_LOG(VERBOSE, "ctl %p, adr %p, dat %p, dat++ %p\n",
+ phw->ado[dsp_index].prHPI_control,
+ phw->ado[dsp_index].prHPI_address,
+ phw->ado[dsp_index].prHPI_data,
+ phw->ado[dsp_index].prHPI_data_auto_inc);
+
+ phw->ado[dsp_index].pa_parent_adapter = pao;
+ }
+
+ phw->pCI2040HPI_error_count = 0;
+ pao->has_control_cache = 0;
+
+ /* Set the default number of DSPs on this card */
+ /* This is (conditionally) adjusted after bootloading */
+ /* of the first DSP in the bootload section. */
+ phw->num_dsp = 1;
+
+ boot_error = hpi6000_adapter_boot_load_dsp(pao, pos_error_code);
+ if (boot_error)
+ return boot_error;
+
+ HPI_DEBUG_LOG(INFO, "bootload DSP OK\n");
+
+ phw->message_buffer_address_on_dsp = 0L;
+ phw->response_buffer_address_on_dsp = 0L;
+
+ /* get info about the adapter by asking the adapter */
+ /* send a HPI_ADAPTER_GET_INFO message */
+ {
+ struct hpi_message hm;
+ struct hpi_response hr0; /* response from DSP 0 */
+ struct hpi_response hr1; /* response from DSP 1 */
+ u16 error = 0;
+
+ HPI_DEBUG_LOG(VERBOSE, "send ADAPTER_GET_INFO\n");
+ memset(&hm, 0, sizeof(hm));
+ hm.type = HPI_TYPE_REQUEST;
+ hm.size = sizeof(struct hpi_message);
+ hm.object = HPI_OBJ_ADAPTER;
+ hm.function = HPI_ADAPTER_GET_INFO;
+ hm.adapter_index = 0;
+ memset(&hr0, 0, sizeof(hr0));
+ memset(&hr1, 0, sizeof(hr1));
+ hr0.size = sizeof(hr0);
+ hr1.size = sizeof(hr1);
+
+ error = hpi6000_message_response_sequence(pao, 0, &hm, &hr0);
+ if (hr0.error) {
+ HPI_DEBUG_LOG(DEBUG, "message error %d\n", hr0.error);
+ return hr0.error;
+ }
+ if (phw->num_dsp == 2) {
+ error = hpi6000_message_response_sequence(pao, 1, &hm,
+ &hr1);
+ if (error)
+ return error;
+ }
+ pao->type = hr0.u.ax.info.adapter_type;
+ pao->index = hr0.u.ax.info.adapter_index;
+ }
+
+ memset(&phw->control_cache[0], 0,
+ sizeof(struct hpi_control_cache_single) *
+ HPI_NMIXER_CONTROLS);
+ /* Read the control cache length to figure out if it is turned on */
+ control_cache_size =
+ hpi_read_word(&phw->ado[0],
+ HPI_HIF_ADDR(control_cache_size_in_bytes));
+ if (control_cache_size) {
+ control_cache_count =
+ hpi_read_word(&phw->ado[0],
+ HPI_HIF_ADDR(control_cache_count));
+
+ phw->p_cache =
+ hpi_alloc_control_cache(control_cache_count,
+ control_cache_size, (unsigned char *)
+ &phw->control_cache[0]
+ );
+ if (phw->p_cache)
+ pao->has_control_cache = 1;
+ }
+
+ HPI_DEBUG_LOG(DEBUG, "get adapter info ASI%04X index %d\n", pao->type,
+ pao->index);
+
+ if (phw->p_cache)
+ phw->p_cache->adap_idx = pao->index;
+
+ return hpi_add_adapter(pao);
+}
+
+static void delete_adapter_obj(struct hpi_adapter_obj *pao)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+
+ if (pao->has_control_cache)
+ hpi_free_control_cache(phw->p_cache);
+
+ /* reset DSPs on adapter */
+ iowrite32(0x0003000F, phw->dw2040_HPICSR + HPI_RESET);
+
+ kfree(phw);
+}
+
+/************************************************************************/
+/* ADAPTER */
+
+static void adapter_get_asserts(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+#ifndef HIDE_PCI_ASSERTS
+ /* if we have PCI2040 asserts then collect them */
+ if ((gw_pci_read_asserts > 0) || (gw_pci_write_asserts > 0)) {
+ phr->u.ax.assert.p1 =
+ gw_pci_read_asserts * 100 + gw_pci_write_asserts;
+ phr->u.ax.assert.p2 = 0;
+ phr->u.ax.assert.count = 1; /* assert count */
+ phr->u.ax.assert.dsp_index = -1; /* "dsp index" */
+ strcpy(phr->u.ax.assert.sz_message, "PCI2040 error");
+ phr->u.ax.assert.dsp_msg_addr = 0;
+ gw_pci_read_asserts = 0;
+ gw_pci_write_asserts = 0;
+ phr->error = 0;
+ } else
+#endif
+ hw_message(pao, phm, phr); /*get DSP asserts */
+
+ return;
+}
+
+/************************************************************************/
+/* LOW-LEVEL */
+
+static short hpi6000_adapter_boot_load_dsp(struct hpi_adapter_obj *pao,
+ u32 *pos_error_code)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ short error;
+ u32 timeout;
+ u32 read = 0;
+ u32 i = 0;
+ u32 data = 0;
+ u32 j = 0;
+ u32 test_addr = 0x80000000;
+ u32 test_data = 0x00000001;
+ u32 dw2040_reset = 0;
+ u32 dsp_index = 0;
+ u32 endian = 0;
+ u32 adapter_info = 0;
+ u32 delay = 0;
+
+ struct dsp_code dsp_code;
+ u16 boot_load_family = 0;
+
+ /* NOTE don't use wAdapterType in this routine. It is not setup yet */
+
+ switch (pao->pci.pci_dev->subsystem_device) {
+ case 0x5100:
+ case 0x5110: /* ASI5100 revB or higher with C6711D */
+ case 0x5200: /* ASI5200 PCIe version of ASI5100 */
+ case 0x6100:
+ case 0x6200:
+ boot_load_family = HPI_ADAPTER_FAMILY_ASI(0x6200);
+ break;
+ default:
+ return HPI6000_ERROR_UNHANDLED_SUBSYS_ID;
+ }
+
+ /* reset all DSPs, indicate two DSPs are present
+ * set RST3-=1 to disconnect HAD8 to set DSP in little endian mode
+ */
+ endian = 0;
+ dw2040_reset = 0x0003000F;
+ iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET);
+
+ /* read back register to make sure PCI2040 chip is functioning
+ * note that bits 4..15 are read-only and so should always return zero,
+ * even though we wrote 1 to them
+ */
+ hpios_delay_micro_seconds(1000);
+ delay = ioread32(phw->dw2040_HPICSR + HPI_RESET);
+
+ if (delay != dw2040_reset) {
+ HPI_DEBUG_LOG(ERROR, "INIT_PCI2040 %x %x\n", dw2040_reset,
+ delay);
+ return HPI6000_ERROR_INIT_PCI2040;
+ }
+
+ /* Indicate that DSP#0,1 is a C6X */
+ iowrite32(0x00000003, phw->dw2040_HPICSR + HPI_DATA_WIDTH);
+ /* set Bit30 and 29 - which will prevent Target aborts from being
+ * issued upon HPI or GP error
+ */
+ iowrite32(0x60000000, phw->dw2040_HPICSR + INTERRUPT_MASK_SET);
+
+ /* isolate DSP HAD8 line from PCI2040 so that
+ * Little endian can be set by pullup
+ */
+ dw2040_reset = dw2040_reset & (~(endian << 3));
+ iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET);
+
+ phw->ado[0].c_dsp_rev = 'B'; /* revB */
+ phw->ado[1].c_dsp_rev = 'B'; /* revB */
+
+ /*Take both DSPs out of reset, setting HAD8 to the correct Endian */
+ dw2040_reset = dw2040_reset & (~0x00000001); /* start DSP 0 */
+ iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET);
+ dw2040_reset = dw2040_reset & (~0x00000002); /* start DSP 1 */
+ iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET);
+
+ /* set HAD8 back to PCI2040, now that DSP set to little endian mode */
+ dw2040_reset = dw2040_reset & (~0x00000008);
+ iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET);
+ /*delay to allow DSP to get going */
+ hpios_delay_micro_seconds(100);
+
+ /* loop through all DSPs, downloading DSP code */
+ for (dsp_index = 0; dsp_index < phw->num_dsp; dsp_index++) {
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+
+ /* configure DSP so that we download code into the SRAM */
+ /* set control reg for little endian, HWOB=1 */
+ iowrite32(0x00010001, pdo->prHPI_control);
+
+ /* test access to the HPI address register (HPIA) */
+ test_data = 0x00000001;
+ for (j = 0; j < 32; j++) {
+ iowrite32(test_data, pdo->prHPI_address);
+ data = ioread32(pdo->prHPI_address);
+ if (data != test_data) {
+ HPI_DEBUG_LOG(ERROR, "INIT_DSPHPI %x %x %x\n",
+ test_data, data, dsp_index);
+ return HPI6000_ERROR_INIT_DSPHPI;
+ }
+ test_data = test_data << 1;
+ }
+
+/* if C6713 the setup PLL to generate 225MHz from 25MHz.
+* Since the PLLDIV1 read is sometimes wrong, even on a C6713,
+* we're going to do this unconditionally
+*/
+/* PLLDIV1 should have a value of 8000 after reset */
+/*
+ if (HpiReadWord(pdo,0x01B7C118) == 0x8000)
+*/
+ {
+ /* C6713 datasheet says we cannot program PLL from HPI,
+ * and indeed if we try to set the PLL multiply from the
+ * HPI, the PLL does not seem to lock,
+ * so we enable the PLL and use the default of x 7
+ */
+ /* bypass PLL */
+ hpi_write_word(pdo, 0x01B7C100, 0x0000);
+ hpios_delay_micro_seconds(100);
+
+ /* ** use default of PLL x7 ** */
+ /* EMIF = 225/3=75MHz */
+ hpi_write_word(pdo, 0x01B7C120, 0x8002);
+ hpios_delay_micro_seconds(100);
+
+ /* peri = 225/2 */
+ hpi_write_word(pdo, 0x01B7C11C, 0x8001);
+ hpios_delay_micro_seconds(100);
+
+ /* cpu = 225/1 */
+ hpi_write_word(pdo, 0x01B7C118, 0x8000);
+
+ /* ~2ms delay */
+ hpios_delay_micro_seconds(2000);
+
+ /* PLL not bypassed */
+ hpi_write_word(pdo, 0x01B7C100, 0x0001);
+ /* ~2ms delay */
+ hpios_delay_micro_seconds(2000);
+ }
+
+ /* test r/w to internal DSP memory
+ * C6711 has L2 cache mapped to 0x0 when reset
+ *
+ * revB - because of bug 3.0.1 last HPI read
+ * (before HPI address issued) must be non-autoinc
+ */
+ /* test each bit in the 32bit word */
+ for (i = 0; i < 100; i++) {
+ test_addr = 0x00000000;
+ test_data = 0x00000001;
+ for (j = 0; j < 32; j++) {
+ hpi_write_word(pdo, test_addr + i, test_data);
+ data = hpi_read_word(pdo, test_addr + i);
+ if (data != test_data) {
+ HPI_DEBUG_LOG(ERROR,
+ "DSP mem %x %x %x %x\n",
+ test_addr + i, test_data,
+ data, dsp_index);
+
+ return HPI6000_ERROR_INIT_DSPINTMEM;
+ }
+ test_data = test_data << 1;
+ }
+ }
+
+ /* memory map of ASI6200
+ 00000000-0000FFFF 16Kx32 internal program
+ 01800000-019FFFFF Internal peripheral
+ 80000000-807FFFFF CE0 2Mx32 SDRAM running @ 100MHz
+ 90000000-9000FFFF CE1 Async peripherals:
+
+ EMIF config
+ ------------
+ Global EMIF control
+ 0 -
+ 1 -
+ 2 -
+ 3 CLK2EN = 1 CLKOUT2 enabled
+ 4 CLK1EN = 0 CLKOUT1 disabled
+ 5 EKEN = 1 <--!! C6713 specific, enables ECLKOUT
+ 6 -
+ 7 NOHOLD = 1 external HOLD disabled
+ 8 HOLDA = 0 HOLDA output is low
+ 9 HOLD = 0 HOLD input is low
+ 10 ARDY = 1 ARDY input is high
+ 11 BUSREQ = 0 BUSREQ output is low
+ 12,13 Reserved = 1
+ */
+ hpi_write_word(pdo, 0x01800000, 0x34A8);
+
+ /* EMIF CE0 setup - 2Mx32 Sync DRAM
+ 31..28 Wr setup
+ 27..22 Wr strobe
+ 21..20 Wr hold
+ 19..16 Rd setup
+ 15..14 -
+ 13..8 Rd strobe
+ 7..4 MTYPE 0011 Sync DRAM 32bits
+ 3 Wr hold MSB
+ 2..0 Rd hold
+ */
+ hpi_write_word(pdo, 0x01800008, 0x00000030);
+
+ /* EMIF SDRAM Extension
+ 31-21 0
+ 20 WR2RD = 0
+ 19-18 WR2DEAC = 1
+ 17 WR2WR = 0
+ 16-15 R2WDQM = 2
+ 14-12 RD2WR = 4
+ 11-10 RD2DEAC = 1
+ 9 RD2RD = 1
+ 8-7 THZP = 10b
+ 6-5 TWR = 2-1 = 01b (tWR = 10ns)
+ 4 TRRD = 0b = 2 ECLK (tRRD = 14ns)
+ 3-1 TRAS = 5-1 = 100b (Tras=42ns = 5 ECLK)
+ 1 CAS latency = 3 ECLK
+ (for Micron 2M32-7 operating at 100Mhz)
+ */
+
+ /* need to use this else DSP code crashes */
+ hpi_write_word(pdo, 0x01800020, 0x001BDF29);
+
+ /* EMIF SDRAM control - set up for a 2Mx32 SDRAM (512x32x4 bank)
+ 31 - -
+ 30 SDBSZ 1 4 bank
+ 29..28 SDRSZ 00 11 row address pins
+ 27..26 SDCSZ 01 8 column address pins
+ 25 RFEN 1 refersh enabled
+ 24 INIT 1 init SDRAM
+ 23..20 TRCD 0001
+ 19..16 TRP 0001
+ 15..12 TRC 0110
+ 11..0 - -
+ */
+ /* need to use this else DSP code crashes */
+ hpi_write_word(pdo, 0x01800018, 0x47117000);
+
+ /* EMIF SDRAM Refresh Timing */
+ hpi_write_word(pdo, 0x0180001C, 0x00000410);
+
+ /*MIF CE1 setup - Async peripherals
+ @100MHz bus speed, each cycle is 10ns,
+ 31..28 Wr setup = 1
+ 27..22 Wr strobe = 3 30ns
+ 21..20 Wr hold = 1
+ 19..16 Rd setup =1
+ 15..14 Ta = 2
+ 13..8 Rd strobe = 3 30ns
+ 7..4 MTYPE 0010 Async 32bits
+ 3 Wr hold MSB =0
+ 2..0 Rd hold = 1
+ */
+ {
+ u32 cE1 =
+ (1L << 28) | (3L << 22) | (1L << 20) | (1L <<
+ 16) | (2L << 14) | (3L << 8) | (2L << 4) | 1L;
+ hpi_write_word(pdo, 0x01800004, cE1);
+ }
+
+ /* delay a little to allow SDRAM and DSP to "get going" */
+ hpios_delay_micro_seconds(1000);
+
+ /* test access to SDRAM */
+ {
+ test_addr = 0x80000000;
+ test_data = 0x00000001;
+ /* test each bit in the 32bit word */
+ for (j = 0; j < 32; j++) {
+ hpi_write_word(pdo, test_addr, test_data);
+ data = hpi_read_word(pdo, test_addr);
+ if (data != test_data) {
+ HPI_DEBUG_LOG(ERROR,
+ "DSP dram %x %x %x %x\n",
+ test_addr, test_data, data,
+ dsp_index);
+
+ return HPI6000_ERROR_INIT_SDRAM1;
+ }
+ test_data = test_data << 1;
+ }
+ /* test every Nth address in the DRAM */
+#define DRAM_SIZE_WORDS 0x200000 /*2_mx32 */
+#define DRAM_INC 1024
+ test_addr = 0x80000000;
+ test_data = 0x0;
+ for (i = 0; i < DRAM_SIZE_WORDS; i = i + DRAM_INC) {
+ hpi_write_word(pdo, test_addr + i, test_data);
+ test_data++;
+ }
+ test_addr = 0x80000000;
+ test_data = 0x0;
+ for (i = 0; i < DRAM_SIZE_WORDS; i = i + DRAM_INC) {
+ data = hpi_read_word(pdo, test_addr + i);
+ if (data != test_data) {
+ HPI_DEBUG_LOG(ERROR,
+ "DSP dram %x %x %x %x\n",
+ test_addr + i, test_data,
+ data, dsp_index);
+ return HPI6000_ERROR_INIT_SDRAM2;
+ }
+ test_data++;
+ }
+
+ }
+
+ /* write the DSP code down into the DSPs memory */
+ error = hpi_dsp_code_open(boot_load_family, pao->pci.pci_dev,
+ &dsp_code, pos_error_code);
+
+ if (error)
+ return error;
+
+ while (1) {
+ u32 length;
+ u32 address;
+ u32 type;
+ u32 *pcode;
+
+ error = hpi_dsp_code_read_word(&dsp_code, &length);
+ if (error)
+ break;
+ if (length == 0xFFFFFFFF)
+ break; /* end of code */
+
+ error = hpi_dsp_code_read_word(&dsp_code, &address);
+ if (error)
+ break;
+ error = hpi_dsp_code_read_word(&dsp_code, &type);
+ if (error)
+ break;
+ error = hpi_dsp_code_read_block(length, &dsp_code,
+ &pcode);
+ if (error)
+ break;
+ error = hpi6000_dsp_block_write32(pao, (u16)dsp_index,
+ address, pcode, length);
+ if (error)
+ break;
+ }
+
+ if (error) {
+ hpi_dsp_code_close(&dsp_code);
+ return error;
+ }
+ /* verify that code was written correctly */
+ /* this time through, assume no errors in DSP code file/array */
+ hpi_dsp_code_rewind(&dsp_code);
+ while (1) {
+ u32 length;
+ u32 address;
+ u32 type;
+ u32 *pcode;
+
+ hpi_dsp_code_read_word(&dsp_code, &length);
+ if (length == 0xFFFFFFFF)
+ break; /* end of code */
+
+ hpi_dsp_code_read_word(&dsp_code, &address);
+ hpi_dsp_code_read_word(&dsp_code, &type);
+ hpi_dsp_code_read_block(length, &dsp_code, &pcode);
+
+ for (i = 0; i < length; i++) {
+ data = hpi_read_word(pdo, address);
+ if (data != *pcode) {
+ error = HPI6000_ERROR_INIT_VERIFY;
+ HPI_DEBUG_LOG(ERROR,
+ "DSP verify %x %x %x %x\n",
+ address, *pcode, data,
+ dsp_index);
+ break;
+ }
+ pcode++;
+ address += 4;
+ }
+ if (error)
+ break;
+ }
+ hpi_dsp_code_close(&dsp_code);
+ if (error)
+ return error;
+
+ /* zero out the hostmailbox */
+ {
+ u32 address = HPI_HIF_ADDR(host_cmd);
+ for (i = 0; i < 4; i++) {
+ hpi_write_word(pdo, address, 0);
+ address += 4;
+ }
+ }
+ /* write the DSP number into the hostmailbox */
+ /* structure before starting the DSP */
+ hpi_write_word(pdo, HPI_HIF_ADDR(dsp_number), dsp_index);
+
+ /* write the DSP adapter Info into the */
+ /* hostmailbox before starting the DSP */
+ if (dsp_index > 0)
+ hpi_write_word(pdo, HPI_HIF_ADDR(adapter_info),
+ adapter_info);
+
+ /* step 3. Start code by sending interrupt */
+ iowrite32(0x00030003, pdo->prHPI_control);
+ hpios_delay_micro_seconds(10000);
+
+ /* wait for a non-zero value in hostcmd -
+ * indicating initialization is complete
+ *
+ * Init could take a while if DSP checks SDRAM memory
+ * Was 200000. Increased to 2000000 for ASI8801 so we
+ * don't get 938 errors.
+ */
+ timeout = 2000000;
+ while (timeout) {
+ do {
+ read = hpi_read_word(pdo,
+ HPI_HIF_ADDR(host_cmd));
+ } while (--timeout
+ && hpi6000_check_PCI2040_error_flag(pao,
+ H6READ));
+
+ if (read)
+ break;
+ /* The following is a workaround for bug #94:
+ * Bluescreen on install and subsequent boots on a
+ * DELL PowerEdge 600SC PC with 1.8GHz P4 and
+ * ServerWorks chipset. Without this delay the system
+ * locks up with a bluescreen (NOT GPF or pagefault).
+ */
+ else
+ hpios_delay_micro_seconds(10000);
+ }
+ if (timeout == 0)
+ return HPI6000_ERROR_INIT_NOACK;
+
+ /* read the DSP adapter Info from the */
+ /* hostmailbox structure after starting the DSP */
+ if (dsp_index == 0) {
+ /*u32 dwTestData=0; */
+ u32 mask = 0;
+
+ adapter_info =
+ hpi_read_word(pdo,
+ HPI_HIF_ADDR(adapter_info));
+ if (HPI_ADAPTER_FAMILY_ASI
+ (HPI_HIF_ADAPTER_INFO_EXTRACT_ADAPTER
+ (adapter_info)) ==
+ HPI_ADAPTER_FAMILY_ASI(0x6200))
+ /* all 6200 cards have this many DSPs */
+ phw->num_dsp = 2;
+
+ /* test that the PLD is programmed */
+ /* and we can read/write 24bits */
+#define PLD_BASE_ADDRESS 0x90000000L /*for ASI6100/6200/8800 */
+
+ switch (boot_load_family) {
+ case HPI_ADAPTER_FAMILY_ASI(0x6200):
+ /* ASI6100/6200 has 24bit path to FPGA */
+ mask = 0xFFFFFF00L;
+ /* ASI5100 uses AX6 code, */
+ /* but has no PLD r/w register to test */
+ if (HPI_ADAPTER_FAMILY_ASI(pao->pci.pci_dev->
+ subsystem_device) ==
+ HPI_ADAPTER_FAMILY_ASI(0x5100))
+ mask = 0x00000000L;
+ /* ASI5200 uses AX6 code, */
+ /* but has no PLD r/w register to test */
+ if (HPI_ADAPTER_FAMILY_ASI(pao->pci.pci_dev->
+ subsystem_device) ==
+ HPI_ADAPTER_FAMILY_ASI(0x5200))
+ mask = 0x00000000L;
+ break;
+ case HPI_ADAPTER_FAMILY_ASI(0x8800):
+ /* ASI8800 has 16bit path to FPGA */
+ mask = 0xFFFF0000L;
+ break;
+ }
+ test_data = 0xAAAAAA00L & mask;
+ /* write to 24 bit Debug register (D31-D8) */
+ hpi_write_word(pdo, PLD_BASE_ADDRESS + 4L, test_data);
+ read = hpi_read_word(pdo,
+ PLD_BASE_ADDRESS + 4L) & mask;
+ if (read != test_data) {
+ HPI_DEBUG_LOG(ERROR, "PLD %x %x\n", test_data,
+ read);
+ return HPI6000_ERROR_INIT_PLDTEST1;
+ }
+ test_data = 0x55555500L & mask;
+ hpi_write_word(pdo, PLD_BASE_ADDRESS + 4L, test_data);
+ read = hpi_read_word(pdo,
+ PLD_BASE_ADDRESS + 4L) & mask;
+ if (read != test_data) {
+ HPI_DEBUG_LOG(ERROR, "PLD %x %x\n", test_data,
+ read);
+ return HPI6000_ERROR_INIT_PLDTEST2;
+ }
+ }
+ } /* for numDSP */
+ return 0;
+}
+
+#define PCI_TIMEOUT 100
+
+static int hpi_set_address(struct dsp_obj *pdo, u32 address)
+{
+ u32 timeout = PCI_TIMEOUT;
+
+ do {
+ iowrite32(address, pdo->prHPI_address);
+ } while (hpi6000_check_PCI2040_error_flag(pdo->pa_parent_adapter,
+ H6WRITE)
+ && --timeout);
+
+ if (timeout)
+ return 0;
+
+ return 1;
+}
+
+/* write one word to the HPI port */
+static void hpi_write_word(struct dsp_obj *pdo, u32 address, u32 data)
+{
+ if (hpi_set_address(pdo, address))
+ return;
+ iowrite32(data, pdo->prHPI_data);
+}
+
+/* read one word from the HPI port */
+static u32 hpi_read_word(struct dsp_obj *pdo, u32 address)
+{
+ u32 data = 0;
+
+ if (hpi_set_address(pdo, address))
+ return 0; /*? No way to return error */
+
+ /* take care of errata in revB DSP (2.0.1) */
+ data = ioread32(pdo->prHPI_data);
+ return data;
+}
+
+/* write a block of 32bit words to the DSP HPI port using auto-inc mode */
+static void hpi_write_block(struct dsp_obj *pdo, u32 address, u32 *pdata,
+ u32 length)
+{
+ u16 length16 = length - 1;
+
+ if (length == 0)
+ return;
+
+ if (hpi_set_address(pdo, address))
+ return;
+
+ iowrite32_rep(pdo->prHPI_data_auto_inc, pdata, length16);
+
+ /* take care of errata in revB DSP (2.0.1) */
+ /* must end with non auto-inc */
+ iowrite32(*(pdata + length - 1), pdo->prHPI_data);
+}
+
+/** read a block of 32bit words from the DSP HPI port using auto-inc mode
+ */
+static void hpi_read_block(struct dsp_obj *pdo, u32 address, u32 *pdata,
+ u32 length)
+{
+ u16 length16 = length - 1;
+
+ if (length == 0)
+ return;
+
+ if (hpi_set_address(pdo, address))
+ return;
+
+ ioread32_rep(pdo->prHPI_data_auto_inc, pdata, length16);
+
+ /* take care of errata in revB DSP (2.0.1) */
+ /* must end with non auto-inc */
+ *(pdata + length - 1) = ioread32(pdo->prHPI_data);
+}
+
+static u16 hpi6000_dsp_block_write32(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 hpi_address, u32 *source, u32 count)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 time_out = PCI_TIMEOUT;
+ int c6711_burst_size = 128;
+ u32 local_hpi_address = hpi_address;
+ int local_count = count;
+ int xfer_size;
+ u32 *pdata = source;
+
+ while (local_count) {
+ if (local_count > c6711_burst_size)
+ xfer_size = c6711_burst_size;
+ else
+ xfer_size = local_count;
+
+ time_out = PCI_TIMEOUT;
+ do {
+ hpi_write_block(pdo, local_hpi_address, pdata,
+ xfer_size);
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE)
+ && --time_out);
+
+ if (!time_out)
+ break;
+ pdata += xfer_size;
+ local_hpi_address += sizeof(u32) * xfer_size;
+ local_count -= xfer_size;
+ }
+
+ if (time_out)
+ return 0;
+ else
+ return 1;
+}
+
+static u16 hpi6000_dsp_block_read32(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 hpi_address, u32 *dest, u32 count)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 time_out = PCI_TIMEOUT;
+ int c6711_burst_size = 16;
+ u32 local_hpi_address = hpi_address;
+ int local_count = count;
+ int xfer_size;
+ u32 *pdata = dest;
+ u32 loop_count = 0;
+
+ while (local_count) {
+ if (local_count > c6711_burst_size)
+ xfer_size = c6711_burst_size;
+ else
+ xfer_size = local_count;
+
+ time_out = PCI_TIMEOUT;
+ do {
+ hpi_read_block(pdo, local_hpi_address, pdata,
+ xfer_size);
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)
+ && --time_out);
+ if (!time_out)
+ break;
+
+ pdata += xfer_size;
+ local_hpi_address += sizeof(u32) * xfer_size;
+ local_count -= xfer_size;
+ loop_count++;
+ }
+
+ if (time_out)
+ return 0;
+ else
+ return 1;
+}
+
+static short hpi6000_message_response_sequence(struct hpi_adapter_obj *pao,
+ u16 dsp_index, struct hpi_message *phm, struct hpi_response *phr)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 timeout;
+ u16 ack;
+ u32 address;
+ u32 length;
+ u32 *p_data;
+ u16 error = 0;
+
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE);
+ if (ack & HPI_HIF_ERROR_MASK) {
+ pao->dsp_crashed++;
+ return HPI6000_ERROR_MSG_RESP_IDLE_TIMEOUT;
+ }
+ pao->dsp_crashed = 0;
+
+ /* get the message address and size */
+ if (phw->message_buffer_address_on_dsp == 0) {
+ timeout = TIMEOUT;
+ do {
+ address =
+ hpi_read_word(pdo,
+ HPI_HIF_ADDR(message_buffer_address));
+ phw->message_buffer_address_on_dsp = address;
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)
+ && --timeout);
+ if (!timeout)
+ return HPI6000_ERROR_MSG_GET_ADR;
+ } else
+ address = phw->message_buffer_address_on_dsp;
+
+ length = phm->size;
+
+ /* send the message */
+ p_data = (u32 *)phm;
+ if (hpi6000_dsp_block_write32(pao, dsp_index, address, p_data,
+ (u16)length / 4))
+ return HPI6000_ERROR_MSG_RESP_BLOCKWRITE32;
+
+ if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_GET_RESP))
+ return HPI6000_ERROR_MSG_RESP_GETRESPCMD;
+ hpi6000_send_dsp_interrupt(pdo);
+
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_GET_RESP);
+ if (ack & HPI_HIF_ERROR_MASK)
+ return HPI6000_ERROR_MSG_RESP_GET_RESP_ACK;
+
+ /* get the response address */
+ if (phw->response_buffer_address_on_dsp == 0) {
+ timeout = TIMEOUT;
+ do {
+ address =
+ hpi_read_word(pdo,
+ HPI_HIF_ADDR(response_buffer_address));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)
+ && --timeout);
+ phw->response_buffer_address_on_dsp = address;
+
+ if (!timeout)
+ return HPI6000_ERROR_RESP_GET_ADR;
+ } else
+ address = phw->response_buffer_address_on_dsp;
+
+ /* read the length of the response back from the DSP */
+ timeout = TIMEOUT;
+ do {
+ length = hpi_read_word(pdo, HPI_HIF_ADDR(length));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) && --timeout);
+ if (!timeout)
+ return HPI6000_ERROR_RESP_GET_LEN;
+
+ if (length > phr->size)
+ return HPI_ERROR_RESPONSE_BUFFER_TOO_SMALL;
+
+ /* get the response */
+ p_data = (u32 *)phr;
+ if (hpi6000_dsp_block_read32(pao, dsp_index, address, p_data,
+ (u16)length / 4))
+ return HPI6000_ERROR_MSG_RESP_BLOCKREAD32;
+
+ /* set i/f back to idle */
+ if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE))
+ return HPI6000_ERROR_MSG_RESP_IDLECMD;
+ hpi6000_send_dsp_interrupt(pdo);
+
+ error = hpi_validate_response(phm, phr);
+ return error;
+}
+
+/* have to set up the below defines to match stuff in the MAP file */
+
+#define MSG_ADDRESS (HPI_HIF_BASE+0x18)
+#define MSG_LENGTH 11
+#define RESP_ADDRESS (HPI_HIF_BASE+0x44)
+#define RESP_LENGTH 16
+#define QUEUE_START (HPI_HIF_BASE+0x88)
+#define QUEUE_SIZE 0x8000
+
+static short hpi6000_send_data_check_adr(u32 address, u32 length_in_dwords)
+{
+/*#define CHECKING // comment this line in to enable checking */
+#ifdef CHECKING
+ if (address < (u32)MSG_ADDRESS)
+ return 0;
+ if (address > (u32)(QUEUE_START + QUEUE_SIZE))
+ return 0;
+ if ((address + (length_in_dwords << 2)) >
+ (u32)(QUEUE_START + QUEUE_SIZE))
+ return 0;
+#else
+ (void)address;
+ (void)length_in_dwords;
+ return 1;
+#endif
+}
+
+static short hpi6000_send_data(struct hpi_adapter_obj *pao, u16 dsp_index,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 data_sent = 0;
+ u16 ack;
+ u32 length, address;
+ u32 *p_data = (u32 *)phm->u.d.u.data.pb_data;
+ u16 time_out = 8;
+
+ (void)phr;
+
+ /* round dwDataSize down to nearest 4 bytes */
+ while ((data_sent < (phm->u.d.u.data.data_size & ~3L))
+ && --time_out) {
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE);
+ if (ack & HPI_HIF_ERROR_MASK)
+ return HPI6000_ERROR_SEND_DATA_IDLE_TIMEOUT;
+
+ if (hpi6000_send_host_command(pao, dsp_index,
+ HPI_HIF_SEND_DATA))
+ return HPI6000_ERROR_SEND_DATA_CMD;
+
+ hpi6000_send_dsp_interrupt(pdo);
+
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_SEND_DATA);
+
+ if (ack & HPI_HIF_ERROR_MASK)
+ return HPI6000_ERROR_SEND_DATA_ACK;
+
+ do {
+ /* get the address and size */
+ address = hpi_read_word(pdo, HPI_HIF_ADDR(address));
+ /* DSP returns number of DWORDS */
+ length = hpi_read_word(pdo, HPI_HIF_ADDR(length));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ));
+
+ if (!hpi6000_send_data_check_adr(address, length))
+ return HPI6000_ERROR_SEND_DATA_ADR;
+
+ /* send the data. break data into 512 DWORD blocks (2K bytes)
+ * and send using block write. 2Kbytes is the max as this is the
+ * memory window given to the HPI data register by the PCI2040
+ */
+
+ {
+ u32 len = length;
+ u32 blk_len = 512;
+ while (len) {
+ if (len < blk_len)
+ blk_len = len;
+ if (hpi6000_dsp_block_write32(pao, dsp_index,
+ address, p_data, blk_len))
+ return HPI6000_ERROR_SEND_DATA_WRITE;
+ address += blk_len * 4;
+ p_data += blk_len;
+ len -= blk_len;
+ }
+ }
+
+ if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE))
+ return HPI6000_ERROR_SEND_DATA_IDLECMD;
+
+ hpi6000_send_dsp_interrupt(pdo);
+
+ data_sent += length * 4;
+ }
+ if (!time_out)
+ return HPI6000_ERROR_SEND_DATA_TIMEOUT;
+ return 0;
+}
+
+static short hpi6000_get_data(struct hpi_adapter_obj *pao, u16 dsp_index,
+ struct hpi_message *phm, struct hpi_response *phr)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 data_got = 0;
+ u16 ack;
+ u32 length, address;
+ u32 *p_data = (u32 *)phm->u.d.u.data.pb_data;
+
+ (void)phr; /* this parameter not used! */
+
+ /* round dwDataSize down to nearest 4 bytes */
+ while (data_got < (phm->u.d.u.data.data_size & ~3L)) {
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE);
+ if (ack & HPI_HIF_ERROR_MASK)
+ return HPI6000_ERROR_GET_DATA_IDLE_TIMEOUT;
+
+ if (hpi6000_send_host_command(pao, dsp_index,
+ HPI_HIF_GET_DATA))
+ return HPI6000_ERROR_GET_DATA_CMD;
+ hpi6000_send_dsp_interrupt(pdo);
+
+ ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_GET_DATA);
+
+ if (ack & HPI_HIF_ERROR_MASK)
+ return HPI6000_ERROR_GET_DATA_ACK;
+
+ /* get the address and size */
+ do {
+ address = hpi_read_word(pdo, HPI_HIF_ADDR(address));
+ length = hpi_read_word(pdo, HPI_HIF_ADDR(length));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ));
+
+ /* read the data */
+ {
+ u32 len = length;
+ u32 blk_len = 512;
+ while (len) {
+ if (len < blk_len)
+ blk_len = len;
+ if (hpi6000_dsp_block_read32(pao, dsp_index,
+ address, p_data, blk_len))
+ return HPI6000_ERROR_GET_DATA_READ;
+ address += blk_len * 4;
+ p_data += blk_len;
+ len -= blk_len;
+ }
+ }
+
+ if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE))
+ return HPI6000_ERROR_GET_DATA_IDLECMD;
+ hpi6000_send_dsp_interrupt(pdo);
+
+ data_got += length * 4;
+ }
+ return 0;
+}
+
+static void hpi6000_send_dsp_interrupt(struct dsp_obj *pdo)
+{
+ iowrite32(0x00030003, pdo->prHPI_control); /* DSPINT */
+}
+
+static short hpi6000_send_host_command(struct hpi_adapter_obj *pao,
+ u16 dsp_index, u32 host_cmd)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 timeout = TIMEOUT;
+
+ /* set command */
+ do {
+ hpi_write_word(pdo, HPI_HIF_ADDR(host_cmd), host_cmd);
+ /* flush the FIFO */
+ hpi_set_address(pdo, HPI_HIF_ADDR(host_cmd));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE) && --timeout);
+
+ /* reset the interrupt bit */
+ iowrite32(0x00040004, pdo->prHPI_control);
+
+ if (timeout)
+ return 0;
+ else
+ return 1;
+}
+
+/* if the PCI2040 has recorded an HPI timeout, reset the error and return 1 */
+static short hpi6000_check_PCI2040_error_flag(struct hpi_adapter_obj *pao,
+ u16 read_or_write)
+{
+ u32 hPI_error;
+
+ struct hpi_hw_obj *phw = pao->priv;
+
+ /* read the error bits from the PCI2040 */
+ hPI_error = ioread32(phw->dw2040_HPICSR + HPI_ERROR_REPORT);
+ if (hPI_error) {
+ /* reset the error flag */
+ iowrite32(0L, phw->dw2040_HPICSR + HPI_ERROR_REPORT);
+ phw->pCI2040HPI_error_count++;
+ if (read_or_write == 1)
+ gw_pci_read_asserts++; /************* inc global */
+ else
+ gw_pci_write_asserts++;
+ return 1;
+ } else
+ return 0;
+}
+
+static short hpi6000_wait_dsp_ack(struct hpi_adapter_obj *pao, u16 dsp_index,
+ u32 ack_value)
+{
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 ack = 0L;
+ u32 timeout;
+ u32 hPIC = 0L;
+
+ /* wait for host interrupt to signal ack is ready */
+ timeout = TIMEOUT;
+ while (--timeout) {
+ hPIC = ioread32(pdo->prHPI_control);
+ if (hPIC & 0x04) /* 0x04 = HINT from DSP */
+ break;
+ }
+ if (timeout == 0)
+ return HPI_HIF_ERROR_MASK;
+
+ /* wait for dwAckValue */
+ timeout = TIMEOUT;
+ while (--timeout) {
+ /* read the ack mailbox */
+ ack = hpi_read_word(pdo, HPI_HIF_ADDR(dsp_ack));
+ if (ack == ack_value)
+ break;
+ if ((ack & HPI_HIF_ERROR_MASK)
+ && !hpi6000_check_PCI2040_error_flag(pao, H6READ))
+ break;
+ /*for (i=0;i<1000;i++) */
+ /* dwPause=i+1; */
+ }
+ if (ack & HPI_HIF_ERROR_MASK)
+ /* indicates bad read from DSP -
+ typically 0xffffff is read for some reason */
+ ack = HPI_HIF_ERROR_MASK;
+
+ if (timeout == 0)
+ ack = HPI_HIF_ERROR_MASK;
+ return (short)ack;
+}
+
+static short hpi6000_update_control_cache(struct hpi_adapter_obj *pao,
+ struct hpi_message *phm)
+{
+ const u16 dsp_index = 0;
+ struct hpi_hw_obj *phw = pao->priv;
+ struct dsp_obj *pdo = &phw->ado[dsp_index];
+ u32 timeout;
+ u32 cache_dirty_flag;
+ u16 err;
+
+ hpios_dsplock_lock(pao);
+
+ timeout = TIMEOUT;
+ do {
+ cache_dirty_flag =
+ hpi_read_word((struct dsp_obj *)pdo,
+ HPI_HIF_ADDR(control_cache_is_dirty));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) && --timeout);
+ if (!timeout) {
+ err = HPI6000_ERROR_CONTROL_CACHE_PARAMS;
+ goto unlock;
+ }
+
+ if (cache_dirty_flag) {
+ /* read the cached controls */
+ u32 address;
+ u32 length;
+
+ timeout = TIMEOUT;
+ if (pdo->control_cache_address_on_dsp == 0) {
+ do {
+ address =
+ hpi_read_word((struct dsp_obj *)pdo,
+ HPI_HIF_ADDR(control_cache_address));
+
+ length = hpi_read_word((struct dsp_obj *)pdo,
+ HPI_HIF_ADDR
+ (control_cache_size_in_bytes));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)
+ && --timeout);
+ if (!timeout) {
+ err = HPI6000_ERROR_CONTROL_CACHE_ADDRLEN;
+ goto unlock;
+ }
+ pdo->control_cache_address_on_dsp = address;
+ pdo->control_cache_length_on_dsp = length;
+ } else {
+ address = pdo->control_cache_address_on_dsp;
+ length = pdo->control_cache_length_on_dsp;
+ }
+
+ if (hpi6000_dsp_block_read32(pao, dsp_index, address,
+ (u32 *)&phw->control_cache[0],
+ length / sizeof(u32))) {
+ err = HPI6000_ERROR_CONTROL_CACHE_READ;
+ goto unlock;
+ }
+ do {
+ hpi_write_word((struct dsp_obj *)pdo,
+ HPI_HIF_ADDR(control_cache_is_dirty), 0);
+ /* flush the FIFO */
+ hpi_set_address(pdo, HPI_HIF_ADDR(host_cmd));
+ } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE)
+ && --timeout);
+ if (!timeout) {
+ err = HPI6000_ERROR_CONTROL_CACHE_FLUSH;
+ goto unlock;
+ }
+
+ }
+ err = 0;
+
+unlock:
+ hpios_dsplock_unlock(pao);
+ return err;
+}
+
+/** Get dsp index for multi DSP adapters only */
+static u16 get_dsp_index(struct hpi_adapter_obj *pao, struct hpi_message *phm)
+{
+ u16 ret = 0;
+ switch (phm->object) {
+ case HPI_OBJ_ISTREAM:
+ if (phm->obj_index < 2)
+ ret = 1;
+ break;
+ case HPI_OBJ_PROFILE:
+ ret = phm->obj_index;
+ break;
+ default:
+ break;
+ }
+ return ret;
+}
+
+/** Complete transaction with DSP
+
+Send message, get response, send or get stream data if any.
+*/
+static void hw_message(struct hpi_adapter_obj *pao, struct hpi_message *phm,
+ struct hpi_response *phr)
+{
+ u16 error = 0;
+ u16 dsp_index = 0;
+ struct hpi_hw_obj *phw = pao->priv;
+ u16 num_dsp = phw->num_dsp;
+
+ if (num_dsp < 2)
+ dsp_index = 0;
+ else {
+ dsp_index = get_dsp_index(pao, phm);
+
+ /* is this checked on the DSP anyway? */
+ if ((phm->function == HPI_ISTREAM_GROUP_ADD)
+ || (phm->function == HPI_OSTREAM_GROUP_ADD)) {
+ struct hpi_message hm;
+ u16 add_index;
+ hm.obj_index = phm->u.d.u.stream.stream_index;
+ hm.object = phm->u.d.u.stream.object_type;
+ add_index = get_dsp_index(pao, &hm);
+ if (add_index != dsp_index) {
+ phr->error = HPI_ERROR_NO_INTERDSP_GROUPS;
+ return;
+ }
+ }
+ }
+
+ hpios_dsplock_lock(pao);
+ error = hpi6000_message_response_sequence(pao, dsp_index, phm, phr);
+
+ if (error) /* something failed in the HPI/DSP interface */
+ goto err;
+
+ if (phr->error) /* something failed in the DSP */
+ goto out;
+
+ switch (phm->function) {
+ case HPI_OSTREAM_WRITE:
+ case HPI_ISTREAM_ANC_WRITE:
+ error = hpi6000_send_data(pao, dsp_index, phm, phr);
+ break;
+ case HPI_ISTREAM_READ:
+ case HPI_OSTREAM_ANC_READ:
+ error = hpi6000_get_data(pao, dsp_index, phm, phr);
+ break;
+ case HPI_ADAPTER_GET_ASSERT:
+ phr->u.ax.assert.dsp_index = 0; /* dsp 0 default */
+ if (num_dsp == 2) {
+ if (!phr->u.ax.assert.count) {
+ /* no assert from dsp 0, check dsp 1 */
+ error = hpi6000_message_response_sequence(pao,
+ 1, phm, phr);
+ phr->u.ax.assert.dsp_index = 1;
+ }
+ }
+ }
+
+err:
+ if (error) {
+ if (error >= HPI_ERROR_BACKEND_BASE) {
+ phr->error = HPI_ERROR_DSP_COMMUNICATION;
+ phr->specific_error = error;
+ } else {
+ phr->error = error;
+ }
+
+ /* just the header of the response is valid */
+ phr->size = sizeof(struct hpi_response_header);
+ }
+out:
+ hpios_dsplock_unlock(pao);
+ return;
+}