From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../amlogic,meson-gpio-intc.txt | 38 ++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt (limited to 'Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt') diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt new file mode 100644 index 000000000..bde63f8f0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -0,0 +1,38 @@ +Amlogic meson GPIO interrupt controller + +Meson SoCs contains an interrupt controller which is able to watch the SoC +pads and generate an interrupt on edge or level. The controller is essentially +a 256 pads to 8 GIC interrupt multiplexer, with a filter block to select edge +or level and polarity. It does not expose all 256 mux inputs because the +documentation shows that the upper part is not mapped to any pad. The actual +number of interrupt exposed depends on the SoC. + +Required properties: + +- compatible : must have "amlogic,meson8-gpio-intc" and either + "amlogic,meson8-gpio-intc" for meson8 SoCs (S802) or + "amlogic,meson8b-gpio-intc" for meson8b SoCs (S805) or + "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or + "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) + "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) + "amlogic,meson-g12a-gpio-intc" for G12A SoCs (S905D2, S905X2, S905Y2) + "amlogic,meson-sm1-gpio-intc" for SM1 SoCs (S905D3, S905X3, S905Y3) + "amlogic,meson-a1-gpio-intc" for A1 SoCs (A113L) + "amlogic,meson-s4-gpio-intc" for S4 SoCs (S802X2, S905Y4, S805X2G, S905W2) +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 2. +- meson,channel-interrupts: Array with the 8 upstream hwirq numbers. These + are the hwirqs used on the parent interrupt controller. + +Example: + +gpio_interrupt: interrupt-controller@9880 { + compatible = "amlogic,meson-gxbb-gpio-intc", + "amlogic,meson-gpio-intc"; + reg = <0x0 0x9880 0x0 0x10>; + interrupt-controller; + #interrupt-cells = <2>; + meson,channel-interrupts = <64 65 66 67 68 69 70 71>; +}; -- cgit v1.2.3