From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- drivers/memory/emif.c | 1201 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1201 insertions(+) create mode 100644 drivers/memory/emif.c (limited to 'drivers/memory/emif.c') diff --git a/drivers/memory/emif.c b/drivers/memory/emif.c new file mode 100644 index 000000000..f30564320 --- /dev/null +++ b/drivers/memory/emif.c @@ -0,0 +1,1201 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * EMIF driver + * + * Copyright (C) 2012 Texas Instruments, Inc. + * + * Aneesh V + * Santosh Shilimkar + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "emif.h" +#include "jedec_ddr.h" +#include "of_memory.h" + +/** + * struct emif_data - Per device static data for driver's use + * @duplicate: Whether the DDR devices attached to this EMIF + * instance are exactly same as that on EMIF1. In + * this case we can save some memory and processing + * @temperature_level: Maximum temperature of LPDDR2 devices attached + * to this EMIF - read from MR4 register. If there + * are two devices attached to this EMIF, this + * value is the maximum of the two temperature + * levels. + * @node: node in the device list + * @base: base address of memory-mapped IO registers. + * @dev: device pointer. + * @regs_cache: An array of 'struct emif_regs' that stores + * calculated register values for different + * frequencies, to avoid re-calculating them on + * each DVFS transition. + * @curr_regs: The set of register values used in the last + * frequency change (i.e. corresponding to the + * frequency in effect at the moment) + * @plat_data: Pointer to saved platform data. + * @debugfs_root: dentry to the root folder for EMIF in debugfs + * @np_ddr: Pointer to ddr device tree node + */ +struct emif_data { + u8 duplicate; + u8 temperature_level; + u8 lpmode; + struct list_head node; + unsigned long irq_state; + void __iomem *base; + struct device *dev; + struct emif_regs *regs_cache[EMIF_MAX_NUM_FREQUENCIES]; + struct emif_regs *curr_regs; + struct emif_platform_data *plat_data; + struct dentry *debugfs_root; + struct device_node *np_ddr; +}; + +static struct emif_data *emif1; +static DEFINE_SPINLOCK(emif_lock); +static unsigned long irq_state; +static LIST_HEAD(device_list); + +#ifdef CONFIG_DEBUG_FS +static void do_emif_regdump_show(struct seq_file *s, struct emif_data *emif, + struct emif_regs *regs) +{ + u32 type = emif->plat_data->device_info->type; + u32 ip_rev = emif->plat_data->ip_rev; + + seq_printf(s, "EMIF register cache dump for %dMHz\n", + regs->freq/1000000); + + seq_printf(s, "ref_ctrl_shdw\t: 0x%08x\n", regs->ref_ctrl_shdw); + seq_printf(s, "sdram_tim1_shdw\t: 0x%08x\n", regs->sdram_tim1_shdw); + seq_printf(s, "sdram_tim2_shdw\t: 0x%08x\n", regs->sdram_tim2_shdw); + seq_printf(s, "sdram_tim3_shdw\t: 0x%08x\n", regs->sdram_tim3_shdw); + + if (ip_rev == EMIF_4D) { + seq_printf(s, "read_idle_ctrl_shdw_normal\t: 0x%08x\n", + regs->read_idle_ctrl_shdw_normal); + seq_printf(s, "read_idle_ctrl_shdw_volt_ramp\t: 0x%08x\n", + regs->read_idle_ctrl_shdw_volt_ramp); + } else if (ip_rev == EMIF_4D5) { + seq_printf(s, "dll_calib_ctrl_shdw_normal\t: 0x%08x\n", + regs->dll_calib_ctrl_shdw_normal); + seq_printf(s, "dll_calib_ctrl_shdw_volt_ramp\t: 0x%08x\n", + regs->dll_calib_ctrl_shdw_volt_ramp); + } + + if (type == DDR_TYPE_LPDDR2_S2 || type == DDR_TYPE_LPDDR2_S4) { + seq_printf(s, "ref_ctrl_shdw_derated\t: 0x%08x\n", + regs->ref_ctrl_shdw_derated); + seq_printf(s, "sdram_tim1_shdw_derated\t: 0x%08x\n", + regs->sdram_tim1_shdw_derated); + seq_printf(s, "sdram_tim3_shdw_derated\t: 0x%08x\n", + regs->sdram_tim3_shdw_derated); + } +} + +static int emif_regdump_show(struct seq_file *s, void *unused) +{ + struct emif_data *emif = s->private; + struct emif_regs **regs_cache; + int i; + + if (emif->duplicate) + regs_cache = emif1->regs_cache; + else + regs_cache = emif->regs_cache; + + for (i = 0; i < EMIF_MAX_NUM_FREQUENCIES && regs_cache[i]; i++) { + do_emif_regdump_show(s, emif, regs_cache[i]); + seq_putc(s, '\n'); + } + + return 0; +} + +DEFINE_SHOW_ATTRIBUTE(emif_regdump); + +static int emif_mr4_show(struct seq_file *s, void *unused) +{ + struct emif_data *emif = s->private; + + seq_printf(s, "MR4=%d\n", emif->temperature_level); + return 0; +} + +DEFINE_SHOW_ATTRIBUTE(emif_mr4); + +static int __init_or_module emif_debugfs_init(struct emif_data *emif) +{ + emif->debugfs_root = debugfs_create_dir(dev_name(emif->dev), NULL); + debugfs_create_file("regcache_dump", S_IRUGO, emif->debugfs_root, emif, + &emif_regdump_fops); + debugfs_create_file("mr4", S_IRUGO, emif->debugfs_root, emif, + &emif_mr4_fops); + return 0; +} + +static void __exit emif_debugfs_exit(struct emif_data *emif) +{ + debugfs_remove_recursive(emif->debugfs_root); + emif->debugfs_root = NULL; +} +#else +static inline int __init_or_module emif_debugfs_init(struct emif_data *emif) +{ + return 0; +} + +static inline void __exit emif_debugfs_exit(struct emif_data *emif) +{ +} +#endif + +/* + * Get bus width used by EMIF. Note that this may be different from the + * bus width of the DDR devices used. For instance two 16-bit DDR devices + * may be connected to a given CS of EMIF. In this case bus width as far + * as EMIF is concerned is 32, where as the DDR bus width is 16 bits. + */ +static u32 get_emif_bus_width(struct emif_data *emif) +{ + u32 width; + void __iomem *base = emif->base; + + width = (readl(base + EMIF_SDRAM_CONFIG) & NARROW_MODE_MASK) + >> NARROW_MODE_SHIFT; + width = width == 0 ? 32 : 16; + + return width; +} + +static void set_lpmode(struct emif_data *emif, u8 lpmode) +{ + u32 temp; + void __iomem *base = emif->base; + + /* + * Workaround for errata i743 - LPDDR2 Power-Down State is Not + * Efficient + * + * i743 DESCRIPTION: + * The EMIF supports power-down state for low power. The EMIF + * automatically puts the SDRAM into power-down after the memory is + * not accessed for a defined number of cycles and the + * EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set to 0x4. + * As the EMIF supports automatic output impedance calibration, a ZQ + * calibration long command is issued every time it exits active + * power-down and precharge power-down modes. The EMIF waits and + * blocks any other command during this calibration. + * The EMIF does not allow selective disabling of ZQ calibration upon + * exit of power-down mode. Due to very short periods of power-down + * cycles, ZQ calibration overhead creates bandwidth issues and + * increases overall system power consumption. On the other hand, + * issuing ZQ calibration long commands when exiting self-refresh is + * still required. + * + * WORKAROUND + * Because there is no power consumption benefit of the power-down due + * to the calibration and there is a performance risk, the guideline + * is to not allow power-down state and, therefore, to not have set + * the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field to 0x4. + */ + if ((emif->plat_data->ip_rev == EMIF_4D) && + (lpmode == EMIF_LP_MODE_PWR_DN)) { + WARN_ONCE(1, + "REG_LP_MODE = LP_MODE_PWR_DN(4) is prohibited by erratum i743 switch to LP_MODE_SELF_REFRESH(2)\n"); + /* rollback LP_MODE to Self-refresh mode */ + lpmode = EMIF_LP_MODE_SELF_REFRESH; + } + + temp = readl(base + EMIF_POWER_MANAGEMENT_CONTROL); + temp &= ~LP_MODE_MASK; + temp |= (lpmode << LP_MODE_SHIFT); + writel(temp, base + EMIF_POWER_MANAGEMENT_CONTROL); +} + +static void do_freq_update(void) +{ + struct emif_data *emif; + + /* + * Workaround for errata i728: Disable LPMODE during FREQ_UPDATE + * + * i728 DESCRIPTION: + * The EMIF automatically puts the SDRAM into self-refresh mode + * after the EMIF has not performed accesses during + * EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM number of DDR clock cycles + * and the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set + * to 0x2. If during a small window the following three events + * occur: + * - The SR_TIMING counter expires + * - And frequency change is requested + * - And OCP access is requested + * Then it causes instable clock on the DDR interface. + * + * WORKAROUND + * To avoid the occurrence of the three events, the workaround + * is to disable the self-refresh when requesting a frequency + * change. Before requesting a frequency change the software must + * program EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x0. When the + * frequency change has been done, the software can reprogram + * EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2 + */ + list_for_each_entry(emif, &device_list, node) { + if (emif->lpmode == EMIF_LP_MODE_SELF_REFRESH) + set_lpmode(emif, EMIF_LP_MODE_DISABLE); + } + + /* + * TODO: Do FREQ_UPDATE here when an API + * is available for this as part of the new + * clock framework + */ + + list_for_each_entry(emif, &device_list, node) { + if (emif->lpmode == EMIF_LP_MODE_SELF_REFRESH) + set_lpmode(emif, EMIF_LP_MODE_SELF_REFRESH); + } +} + +/* Find addressing table entry based on the device's type and density */ +static const struct lpddr2_addressing *get_addressing_table( + const struct ddr_device_info *device_info) +{ + u32 index, type, density; + + type = device_info->type; + density = device_info->density; + + switch (type) { + case DDR_TYPE_LPDDR2_S4: + index = density - 1; + break; + case DDR_TYPE_LPDDR2_S2: + switch (density) { + case DDR_DENSITY_1Gb: + case DDR_DENSITY_2Gb: + index = density + 3; + break; + default: + index = density - 1; + } + break; + default: + return NULL; + } + + return &lpddr2_jedec_addressing_table[index]; +} + +static u32 get_zq_config_reg(const struct lpddr2_addressing *addressing, + bool cs1_used, bool cal_resistors_per_cs) +{ + u32 zq = 0, val = 0; + + val = EMIF_ZQCS_INTERVAL_US * 1000 / addressing->tREFI_ns; + zq |= val << ZQ_REFINTERVAL_SHIFT; + + val = DIV_ROUND_UP(T_ZQCL_DEFAULT_NS, T_ZQCS_DEFAULT_NS) - 1; + zq |= val << ZQ_ZQCL_MULT_SHIFT; + + val = DIV_ROUND_UP(T_ZQINIT_DEFAULT_NS, T_ZQCL_DEFAULT_NS) - 1; + zq |= val << ZQ_ZQINIT_MULT_SHIFT; + + zq |= ZQ_SFEXITEN_ENABLE << ZQ_SFEXITEN_SHIFT; + + if (cal_resistors_per_cs) + zq |= ZQ_DUALCALEN_ENABLE << ZQ_DUALCALEN_SHIFT; + else + zq |= ZQ_DUALCALEN_DISABLE << ZQ_DUALCALEN_SHIFT; + + zq |= ZQ_CS0EN_MASK; /* CS0 is used for sure */ + + val = cs1_used ? 1 : 0; + zq |= val << ZQ_CS1EN_SHIFT; + + return zq; +} + +static u32 get_temp_alert_config(const struct lpddr2_addressing *addressing, + const struct emif_custom_configs *custom_configs, bool cs1_used, + u32 sdram_io_width, u32 emif_bus_width) +{ + u32 alert = 0, interval, devcnt; + + if (custom_configs && (custom_configs->mask & + EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL)) + interval = custom_configs->temp_alert_poll_interval_ms; + else + interval = TEMP_ALERT_POLL_INTERVAL_DEFAULT_MS; + + interval *= 1000000; /* Convert to ns */ + interval /= addressing->tREFI_ns; /* Convert to refresh cycles */ + alert |= (interval << TA_REFINTERVAL_SHIFT); + + /* + * sdram_io_width is in 'log2(x) - 1' form. Convert emif_bus_width + * also to this form and subtract to get TA_DEVCNT, which is + * in log2(x) form. + */ + emif_bus_width = __fls(emif_bus_width) - 1; + devcnt = emif_bus_width - sdram_io_width; + alert |= devcnt << TA_DEVCNT_SHIFT; + + /* DEVWDT is in 'log2(x) - 3' form */ + alert |= (sdram_io_width - 2) << TA_DEVWDT_SHIFT; + + alert |= 1 << TA_SFEXITEN_SHIFT; + alert |= 1 << TA_CS0EN_SHIFT; + alert |= (cs1_used ? 1 : 0) << TA_CS1EN_SHIFT; + + return alert; +} + +static u32 get_pwr_mgmt_ctrl(u32 freq, struct emif_data *emif, u32 ip_rev) +{ + u32 pwr_mgmt_ctrl = 0, timeout; + u32 lpmode = EMIF_LP_MODE_SELF_REFRESH; + u32 timeout_perf = EMIF_LP_MODE_TIMEOUT_PERFORMANCE; + u32 timeout_pwr = EMIF_LP_MODE_TIMEOUT_POWER; + u32 freq_threshold = EMIF_LP_MODE_FREQ_THRESHOLD; + u32 mask; + u8 shift; + + struct emif_custom_configs *cust_cfgs = emif->plat_data->custom_configs; + + if (cust_cfgs && (cust_cfgs->mask & EMIF_CUSTOM_CONFIG_LPMODE)) { + lpmode = cust_cfgs->lpmode; + timeout_perf = cust_cfgs->lpmode_timeout_performance; + timeout_pwr = cust_cfgs->lpmode_timeout_power; + freq_threshold = cust_cfgs->lpmode_freq_threshold; + } + + /* Timeout based on DDR frequency */ + timeout = freq >= freq_threshold ? timeout_perf : timeout_pwr; + + /* + * The value to be set in register is "log2(timeout) - 3" + * if timeout < 16 load 0 in register + * if timeout is not a power of 2, round to next highest power of 2 + */ + if (timeout < 16) { + timeout = 0; + } else { + if (timeout & (timeout - 1)) + timeout <<= 1; + timeout = __fls(timeout) - 3; + } + + switch (lpmode) { + case EMIF_LP_MODE_CLOCK_STOP: + shift = CS_TIM_SHIFT; + mask = CS_TIM_MASK; + break; + case EMIF_LP_MODE_SELF_REFRESH: + /* Workaround for errata i735 */ + if (timeout < 6) + timeout = 6; + + shift = SR_TIM_SHIFT; + mask = SR_TIM_MASK; + break; + case EMIF_LP_MODE_PWR_DN: + shift = PD_TIM_SHIFT; + mask = PD_TIM_MASK; + break; + case EMIF_LP_MODE_DISABLE: + default: + mask = 0; + shift = 0; + break; + } + /* Round to maximum in case of overflow, BUT warn! */ + if (lpmode != EMIF_LP_MODE_DISABLE && timeout > mask >> shift) { + pr_err("TIMEOUT Overflow - lpmode=%d perf=%d pwr=%d freq=%d\n", + lpmode, + timeout_perf, + timeout_pwr, + freq_threshold); + WARN(1, "timeout=0x%02x greater than 0x%02x. Using max\n", + timeout, mask >> shift); + timeout = mask >> shift; + } + + /* Setup required timing */ + pwr_mgmt_ctrl = (timeout << shift) & mask; + /* setup a default mask for rest of the modes */ + pwr_mgmt_ctrl |= (SR_TIM_MASK | CS_TIM_MASK | PD_TIM_MASK) & + ~mask; + + /* No CS_TIM in EMIF_4D5 */ + if (ip_rev == EMIF_4D5) + pwr_mgmt_ctrl &= ~CS_TIM_MASK; + + pwr_mgmt_ctrl |= lpmode << LP_MODE_SHIFT; + + return pwr_mgmt_ctrl; +} + +/* + * Get the temperature level of the EMIF instance: + * Reads the MR4 register of attached SDRAM parts to find out the temperature + * level. If there are two parts attached(one on each CS), then the temperature + * level for the EMIF instance is the higher of the two temperatures. + */ +static void get_temperature_level(struct emif_data *emif) +{ + u32 temp, temperature_level; + void __iomem *base; + + base = emif->base; + + /* Read mode register 4 */ + writel(DDR_MR4, base + EMIF_LPDDR2_MODE_REG_CONFIG); + temperature_level = readl(base + EMIF_LPDDR2_MODE_REG_DATA); + temperature_level = (temperature_level & MR4_SDRAM_REF_RATE_MASK) >> + MR4_SDRAM_REF_RATE_SHIFT; + + if (emif->plat_data->device_info->cs1_used) { + writel(DDR_MR4 | CS_MASK, base + EMIF_LPDDR2_MODE_REG_CONFIG); + temp = readl(base + EMIF_LPDDR2_MODE_REG_DATA); + temp = (temp & MR4_SDRAM_REF_RATE_MASK) + >> MR4_SDRAM_REF_RATE_SHIFT; + temperature_level = max(temp, temperature_level); + } + + /* treat everything less than nominal(3) in MR4 as nominal */ + if (unlikely(temperature_level < SDRAM_TEMP_NOMINAL)) + temperature_level = SDRAM_TEMP_NOMINAL; + + /* if we get reserved value in MR4 persist with the existing value */ + if (likely(temperature_level != SDRAM_TEMP_RESERVED_4)) + emif->temperature_level = temperature_level; +} + +/* + * setup_temperature_sensitive_regs() - set the timings for temperature + * sensitive registers. This happens once at initialisation time based + * on the temperature at boot time and subsequently based on the temperature + * alert interrupt. Temperature alert can happen when the temperature + * increases or drops. So this function can have the effect of either + * derating the timings or going back to nominal values. + */ +static void setup_temperature_sensitive_regs(struct emif_data *emif, + struct emif_regs *regs) +{ + u32 tim1, tim3, ref_ctrl, type; + void __iomem *base = emif->base; + u32 temperature; + + type = emif->plat_data->device_info->type; + + tim1 = regs->sdram_tim1_shdw; + tim3 = regs->sdram_tim3_shdw; + ref_ctrl = regs->ref_ctrl_shdw; + + /* No de-rating for non-lpddr2 devices */ + if (type != DDR_TYPE_LPDDR2_S2 && type != DDR_TYPE_LPDDR2_S4) + goto out; + + temperature = emif->temperature_level; + if (temperature == SDRAM_TEMP_HIGH_DERATE_REFRESH) { + ref_ctrl = regs->ref_ctrl_shdw_derated; + } else if (temperature == SDRAM_TEMP_HIGH_DERATE_REFRESH_AND_TIMINGS) { + tim1 = regs->sdram_tim1_shdw_derated; + tim3 = regs->sdram_tim3_shdw_derated; + ref_ctrl = regs->ref_ctrl_shdw_derated; + } + +out: + writel(tim1, base + EMIF_SDRAM_TIMING_1_SHDW); + writel(tim3, base + EMIF_SDRAM_TIMING_3_SHDW); + writel(ref_ctrl, base + EMIF_SDRAM_REFRESH_CTRL_SHDW); +} + +static irqreturn_t handle_temp_alert(void __iomem *base, struct emif_data *emif) +{ + u32 old_temp_level; + irqreturn_t ret = IRQ_HANDLED; + struct emif_custom_configs *custom_configs; + + spin_lock_irqsave(&emif_lock, irq_state); + old_temp_level = emif->temperature_level; + get_temperature_level(emif); + + if (unlikely(emif->temperature_level == old_temp_level)) { + goto out; + } else if (!emif->curr_regs) { + dev_err(emif->dev, "temperature alert before registers are calculated, not de-rating timings\n"); + goto out; + } + + custom_configs = emif->plat_data->custom_configs; + + /* + * IF we detect higher than "nominal rating" from DDR sensor + * on an unsupported DDR part, shutdown system + */ + if (custom_configs && !(custom_configs->mask & + EMIF_CUSTOM_CONFIG_EXTENDED_TEMP_PART)) { + if (emif->temperature_level >= SDRAM_TEMP_HIGH_DERATE_REFRESH) { + dev_err(emif->dev, + "%s:NOT Extended temperature capable memory. Converting MR4=0x%02x as shutdown event\n", + __func__, emif->temperature_level); + /* + * Temperature far too high - do kernel_power_off() + * from thread context + */ + emif->temperature_level = SDRAM_TEMP_VERY_HIGH_SHUTDOWN; + ret = IRQ_WAKE_THREAD; + goto out; + } + } + + if (emif->temperature_level < old_temp_level || + emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN) { + /* + * Temperature coming down - defer handling to thread OR + * Temperature far too high - do kernel_power_off() from + * thread context + */ + ret = IRQ_WAKE_THREAD; + } else { + /* Temperature is going up - handle immediately */ + setup_temperature_sensitive_regs(emif, emif->curr_regs); + do_freq_update(); + } + +out: + spin_unlock_irqrestore(&emif_lock, irq_state); + return ret; +} + +static irqreturn_t emif_interrupt_handler(int irq, void *dev_id) +{ + u32 interrupts; + struct emif_data *emif = dev_id; + void __iomem *base = emif->base; + struct device *dev = emif->dev; + irqreturn_t ret = IRQ_HANDLED; + + /* Save the status and clear it */ + interrupts = readl(base + EMIF_SYSTEM_OCP_INTERRUPT_STATUS); + writel(interrupts, base + EMIF_SYSTEM_OCP_INTERRUPT_STATUS); + + /* + * Handle temperature alert + * Temperature alert should be same for all ports + * So, it's enough to process it only for one of the ports + */ + if (interrupts & TA_SYS_MASK) + ret = handle_temp_alert(base, emif); + + if (interrupts & ERR_SYS_MASK) + dev_err(dev, "Access error from SYS port - %x\n", interrupts); + + if (emif->plat_data->hw_caps & EMIF_HW_CAPS_LL_INTERFACE) { + /* Save the status and clear it */ + interrupts = readl(base + EMIF_LL_OCP_INTERRUPT_STATUS); + writel(interrupts, base + EMIF_LL_OCP_INTERRUPT_STATUS); + + if (interrupts & ERR_LL_MASK) + dev_err(dev, "Access error from LL port - %x\n", + interrupts); + } + + return ret; +} + +static irqreturn_t emif_threaded_isr(int irq, void *dev_id) +{ + struct emif_data *emif = dev_id; + + if (emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN) { + dev_emerg(emif->dev, "SDRAM temperature exceeds operating limit.. Needs shut down!!!\n"); + + /* If we have Power OFF ability, use it, else try restarting */ + if (kernel_can_power_off()) { + kernel_power_off(); + } else { + WARN(1, "FIXME: NO pm_power_off!!! trying restart\n"); + kernel_restart("SDRAM Over-temp Emergency restart"); + } + return IRQ_HANDLED; + } + + spin_lock_irqsave(&emif_lock, irq_state); + + if (emif->curr_regs) { + setup_temperature_sensitive_regs(emif, emif->curr_regs); + do_freq_update(); + } else { + dev_err(emif->dev, "temperature alert before registers are calculated, not de-rating timings\n"); + } + + spin_unlock_irqrestore(&emif_lock, irq_state); + + return IRQ_HANDLED; +} + +static void clear_all_interrupts(struct emif_data *emif) +{ + void __iomem *base = emif->base; + + writel(readl(base + EMIF_SYSTEM_OCP_INTERRUPT_STATUS), + base + EMIF_SYSTEM_OCP_INTERRUPT_STATUS); + if (emif->plat_data->hw_caps & EMIF_HW_CAPS_LL_INTERFACE) + writel(readl(base + EMIF_LL_OCP_INTERRUPT_STATUS), + base + EMIF_LL_OCP_INTERRUPT_STATUS); +} + +static void disable_and_clear_all_interrupts(struct emif_data *emif) +{ + void __iomem *base = emif->base; + + /* Disable all interrupts */ + writel(readl(base + EMIF_SYSTEM_OCP_INTERRUPT_ENABLE_SET), + base + EMIF_SYSTEM_OCP_INTERRUPT_ENABLE_CLEAR); + if (emif->plat_data->hw_caps & EMIF_HW_CAPS_LL_INTERFACE) + writel(readl(base + EMIF_LL_OCP_INTERRUPT_ENABLE_SET), + base + EMIF_LL_OCP_INTERRUPT_ENABLE_CLEAR); + + /* Clear all interrupts */ + clear_all_interrupts(emif); +} + +static int __init_or_module setup_interrupts(struct emif_data *emif, u32 irq) +{ + u32 interrupts, type; + void __iomem *base = emif->base; + + type = emif->plat_data->device_info->type; + + clear_all_interrupts(emif); + + /* Enable interrupts for SYS interface */ + interrupts = EN_ERR_SYS_MASK; + if (type == DDR_TYPE_LPDDR2_S2 || type == DDR_TYPE_LPDDR2_S4) + interrupts |= EN_TA_SYS_MASK; + writel(interrupts, base + EMIF_SYSTEM_OCP_INTERRUPT_ENABLE_SET); + + /* Enable interrupts for LL interface */ + if (emif->plat_data->hw_caps & EMIF_HW_CAPS_LL_INTERFACE) { + /* TA need not be enabled for LL */ + interrupts = EN_ERR_LL_MASK; + writel(interrupts, base + EMIF_LL_OCP_INTERRUPT_ENABLE_SET); + } + + /* setup IRQ handlers */ + return devm_request_threaded_irq(emif->dev, irq, + emif_interrupt_handler, + emif_threaded_isr, + 0, dev_name(emif->dev), + emif); + +} + +static void __init_or_module emif_onetime_settings(struct emif_data *emif) +{ + u32 pwr_mgmt_ctrl, zq, temp_alert_cfg; + void __iomem *base = emif->base; + const struct lpddr2_addressing *addressing; + const struct ddr_device_info *device_info; + + device_info = emif->plat_data->device_info; + addressing = get_addressing_table(device_info); + + /* + * Init power management settings + * We don't know the frequency yet. Use a high frequency + * value for a conservative timeout setting + */ + pwr_mgmt_ctrl = get_pwr_mgmt_ctrl(1000000000, emif, + emif->plat_data->ip_rev); + emif->lpmode = (pwr_mgmt_ctrl & LP_MODE_MASK) >> LP_MODE_SHIFT; + writel(pwr_mgmt_ctrl, base + EMIF_POWER_MANAGEMENT_CONTROL); + + /* Init ZQ calibration settings */ + zq = get_zq_config_reg(addressing, device_info->cs1_used, + device_info->cal_resistors_per_cs); + writel(zq, base + EMIF_SDRAM_OUTPUT_IMPEDANCE_CALIBRATION_CONFIG); + + /* Check temperature level temperature level*/ + get_temperature_level(emif); + if (emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN) + dev_emerg(emif->dev, "SDRAM temperature exceeds operating limit.. Needs shut down!!!\n"); + + /* Init temperature polling */ + temp_alert_cfg = get_temp_alert_config(addressing, + emif->plat_data->custom_configs, device_info->cs1_used, + device_info->io_width, get_emif_bus_width(emif)); + writel(temp_alert_cfg, base + EMIF_TEMPERATURE_ALERT_CONFIG); + + /* + * Program external PHY control registers that are not frequency + * dependent + */ + if (emif->plat_data->phy_type != EMIF_PHY_TYPE_INTELLIPHY) + return; + writel(EMIF_EXT_PHY_CTRL_1_VAL, base + EMIF_EXT_PHY_CTRL_1_SHDW); + writel(EMIF_EXT_PHY_CTRL_5_VAL, base + EMIF_EXT_PHY_CTRL_5_SHDW); + writel(EMIF_EXT_PHY_CTRL_6_VAL, base + EMIF_EXT_PHY_CTRL_6_SHDW); + writel(EMIF_EXT_PHY_CTRL_7_VAL, base + EMIF_EXT_PHY_CTRL_7_SHDW); + writel(EMIF_EXT_PHY_CTRL_8_VAL, base + EMIF_EXT_PHY_CTRL_8_SHDW); + writel(EMIF_EXT_PHY_CTRL_9_VAL, base + EMIF_EXT_PHY_CTRL_9_SHDW); + writel(EMIF_EXT_PHY_CTRL_10_VAL, base + EMIF_EXT_PHY_CTRL_10_SHDW); + writel(EMIF_EXT_PHY_CTRL_11_VAL, base + EMIF_EXT_PHY_CTRL_11_SHDW); + writel(EMIF_EXT_PHY_CTRL_12_VAL, base + EMIF_EXT_PHY_CTRL_12_SHDW); + writel(EMIF_EXT_PHY_CTRL_13_VAL, base + EMIF_EXT_PHY_CTRL_13_SHDW); + writel(EMIF_EXT_PHY_CTRL_14_VAL, base + EMIF_EXT_PHY_CTRL_14_SHDW); + writel(EMIF_EXT_PHY_CTRL_15_VAL, base + EMIF_EXT_PHY_CTRL_15_SHDW); + writel(EMIF_EXT_PHY_CTRL_16_VAL, base + EMIF_EXT_PHY_CTRL_16_SHDW); + writel(EMIF_EXT_PHY_CTRL_17_VAL, base + EMIF_EXT_PHY_CTRL_17_SHDW); + writel(EMIF_EXT_PHY_CTRL_18_VAL, base + EMIF_EXT_PHY_CTRL_18_SHDW); + writel(EMIF_EXT_PHY_CTRL_19_VAL, base + EMIF_EXT_PHY_CTRL_19_SHDW); + writel(EMIF_EXT_PHY_CTRL_20_VAL, base + EMIF_EXT_PHY_CTRL_20_SHDW); + writel(EMIF_EXT_PHY_CTRL_21_VAL, base + EMIF_EXT_PHY_CTRL_21_SHDW); + writel(EMIF_EXT_PHY_CTRL_22_VAL, base + EMIF_EXT_PHY_CTRL_22_SHDW); + writel(EMIF_EXT_PHY_CTRL_23_VAL, base + EMIF_EXT_PHY_CTRL_23_SHDW); + writel(EMIF_EXT_PHY_CTRL_24_VAL, base + EMIF_EXT_PHY_CTRL_24_SHDW); +} + +static void get_default_timings(struct emif_data *emif) +{ + struct emif_platform_data *pd = emif->plat_data; + + pd->timings = lpddr2_jedec_timings; + pd->timings_arr_size = ARRAY_SIZE(lpddr2_jedec_timings); + + dev_warn(emif->dev, "%s: using default timings\n", __func__); +} + +static int is_dev_data_valid(u32 type, u32 density, u32 io_width, u32 phy_type, + u32 ip_rev, struct device *dev) +{ + int valid; + + valid = (type == DDR_TYPE_LPDDR2_S4 || + type == DDR_TYPE_LPDDR2_S2) + && (density >= DDR_DENSITY_64Mb + && density <= DDR_DENSITY_8Gb) + && (io_width >= DDR_IO_WIDTH_8 + && io_width <= DDR_IO_WIDTH_32); + + /* Combinations of EMIF and PHY revisions that we support today */ + switch (ip_rev) { + case EMIF_4D: + valid = valid && (phy_type == EMIF_PHY_TYPE_ATTILAPHY); + break; + case EMIF_4D5: + valid = valid && (phy_type == EMIF_PHY_TYPE_INTELLIPHY); + break; + default: + valid = 0; + } + + if (!valid) + dev_err(dev, "%s: invalid DDR details\n", __func__); + return valid; +} + +static int is_custom_config_valid(struct emif_custom_configs *cust_cfgs, + struct device *dev) +{ + int valid = 1; + + if ((cust_cfgs->mask & EMIF_CUSTOM_CONFIG_LPMODE) && + (cust_cfgs->lpmode != EMIF_LP_MODE_DISABLE)) + valid = cust_cfgs->lpmode_freq_threshold && + cust_cfgs->lpmode_timeout_performance && + cust_cfgs->lpmode_timeout_power; + + if (cust_cfgs->mask & EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL) + valid = valid && cust_cfgs->temp_alert_poll_interval_ms; + + if (!valid) + dev_warn(dev, "%s: invalid custom configs\n", __func__); + + return valid; +} + +#if defined(CONFIG_OF) +static void __init_or_module of_get_custom_configs(struct device_node *np_emif, + struct emif_data *emif) +{ + struct emif_custom_configs *cust_cfgs = NULL; + int len; + const __be32 *lpmode, *poll_intvl; + + lpmode = of_get_property(np_emif, "low-power-mode", &len); + poll_intvl = of_get_property(np_emif, "temp-alert-poll-interval", &len); + + if (lpmode || poll_intvl) + cust_cfgs = devm_kzalloc(emif->dev, sizeof(*cust_cfgs), + GFP_KERNEL); + + if (!cust_cfgs) + return; + + if (lpmode) { + cust_cfgs->mask |= EMIF_CUSTOM_CONFIG_LPMODE; + cust_cfgs->lpmode = be32_to_cpup(lpmode); + of_property_read_u32(np_emif, + "low-power-mode-timeout-performance", + &cust_cfgs->lpmode_timeout_performance); + of_property_read_u32(np_emif, + "low-power-mode-timeout-power", + &cust_cfgs->lpmode_timeout_power); + of_property_read_u32(np_emif, + "low-power-mode-freq-threshold", + &cust_cfgs->lpmode_freq_threshold); + } + + if (poll_intvl) { + cust_cfgs->mask |= + EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL; + cust_cfgs->temp_alert_poll_interval_ms = + be32_to_cpup(poll_intvl); + } + + if (of_find_property(np_emif, "extended-temp-part", &len)) + cust_cfgs->mask |= EMIF_CUSTOM_CONFIG_EXTENDED_TEMP_PART; + + if (!is_custom_config_valid(cust_cfgs, emif->dev)) { + devm_kfree(emif->dev, cust_cfgs); + return; + } + + emif->plat_data->custom_configs = cust_cfgs; +} + +static void __init_or_module of_get_ddr_info(struct device_node *np_emif, + struct device_node *np_ddr, + struct ddr_device_info *dev_info) +{ + u32 density = 0, io_width = 0; + int len; + + if (of_find_property(np_emif, "cs1-used", &len)) + dev_info->cs1_used = true; + + if (of_find_property(np_emif, "cal-resistor-per-cs", &len)) + dev_info->cal_resistors_per_cs = true; + + if (of_device_is_compatible(np_ddr, "jedec,lpddr2-s4")) + dev_info->type = DDR_TYPE_LPDDR2_S4; + else if (of_device_is_compatible(np_ddr, "jedec,lpddr2-s2")) + dev_info->type = DDR_TYPE_LPDDR2_S2; + + of_property_read_u32(np_ddr, "density", &density); + of_property_read_u32(np_ddr, "io-width", &io_width); + + /* Convert from density in Mb to the density encoding in jedc_ddr.h */ + if (density & (density - 1)) + dev_info->density = 0; + else + dev_info->density = __fls(density) - 5; + + /* Convert from io_width in bits to io_width encoding in jedc_ddr.h */ + if (io_width & (io_width - 1)) + dev_info->io_width = 0; + else + dev_info->io_width = __fls(io_width) - 1; +} + +static struct emif_data * __init_or_module of_get_memory_device_details( + struct device_node *np_emif, struct device *dev) +{ + struct emif_data *emif = NULL; + struct ddr_device_info *dev_info = NULL; + struct emif_platform_data *pd = NULL; + struct device_node *np_ddr; + int len; + + np_ddr = of_parse_phandle(np_emif, "device-handle", 0); + if (!np_ddr) + goto error; + emif = devm_kzalloc(dev, sizeof(struct emif_data), GFP_KERNEL); + pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL); + dev_info = devm_kzalloc(dev, sizeof(*dev_info), GFP_KERNEL); + + if (!emif || !pd || !dev_info) { + dev_err(dev, "%s: Out of memory!!\n", + __func__); + goto error; + } + + emif->plat_data = pd; + pd->device_info = dev_info; + emif->dev = dev; + emif->np_ddr = np_ddr; + emif->temperature_level = SDRAM_TEMP_NOMINAL; + + if (of_device_is_compatible(np_emif, "ti,emif-4d")) + emif->plat_data->ip_rev = EMIF_4D; + else if (of_device_is_compatible(np_emif, "ti,emif-4d5")) + emif->plat_data->ip_rev = EMIF_4D5; + + of_property_read_u32(np_emif, "phy-type", &pd->phy_type); + + if (of_find_property(np_emif, "hw-caps-ll-interface", &len)) + pd->hw_caps |= EMIF_HW_CAPS_LL_INTERFACE; + + of_get_ddr_info(np_emif, np_ddr, dev_info); + if (!is_dev_data_valid(pd->device_info->type, pd->device_info->density, + pd->device_info->io_width, pd->phy_type, pd->ip_rev, + emif->dev)) { + dev_err(dev, "%s: invalid device data!!\n", __func__); + goto error; + } + /* + * For EMIF instances other than EMIF1 see if the devices connected + * are exactly same as on EMIF1(which is typically the case). If so, + * mark it as a duplicate of EMIF1. This will save some memory and + * computation. + */ + if (emif1 && emif1->np_ddr == np_ddr) { + emif->duplicate = true; + goto out; + } else if (emif1) { + dev_warn(emif->dev, "%s: Non-symmetric DDR geometry\n", + __func__); + } + + of_get_custom_configs(np_emif, emif); + emif->plat_data->timings = of_get_ddr_timings(np_ddr, emif->dev, + emif->plat_data->device_info->type, + &emif->plat_data->timings_arr_size); + + emif->plat_data->min_tck = of_get_min_tck(np_ddr, emif->dev); + goto out; + +error: + return NULL; +out: + return emif; +} + +#else + +static struct emif_data * __init_or_module of_get_memory_device_details( + struct device_node *np_emif, struct device *dev) +{ + return NULL; +} +#endif + +static struct emif_data *__init_or_module get_device_details( + struct platform_device *pdev) +{ + u32 size; + struct emif_data *emif = NULL; + struct ddr_device_info *dev_info; + struct emif_custom_configs *cust_cfgs; + struct emif_platform_data *pd; + struct device *dev; + void *temp; + + pd = pdev->dev.platform_data; + dev = &pdev->dev; + + if (!(pd && pd->device_info && is_dev_data_valid(pd->device_info->type, + pd->device_info->density, pd->device_info->io_width, + pd->phy_type, pd->ip_rev, dev))) { + dev_err(dev, "%s: invalid device data\n", __func__); + goto error; + } + + emif = devm_kzalloc(dev, sizeof(*emif), GFP_KERNEL); + temp = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL); + dev_info = devm_kzalloc(dev, sizeof(*dev_info), GFP_KERNEL); + + if (!emif || !temp || !dev_info) + goto error; + + memcpy(temp, pd, sizeof(*pd)); + pd = temp; + memcpy(dev_info, pd->device_info, sizeof(*dev_info)); + + pd->device_info = dev_info; + emif->plat_data = pd; + emif->dev = dev; + emif->temperature_level = SDRAM_TEMP_NOMINAL; + + /* + * For EMIF instances other than EMIF1 see if the devices connected + * are exactly same as on EMIF1(which is typically the case). If so, + * mark it as a duplicate of EMIF1 and skip copying timings data. + * This will save some memory and some computation later. + */ + emif->duplicate = emif1 && (memcmp(dev_info, + emif1->plat_data->device_info, + sizeof(struct ddr_device_info)) == 0); + + if (emif->duplicate) { + pd->timings = NULL; + pd->min_tck = NULL; + goto out; + } else if (emif1) { + dev_warn(emif->dev, "%s: Non-symmetric DDR geometry\n", + __func__); + } + + /* + * Copy custom configs - ignore allocation error, if any, as + * custom_configs is not very critical + */ + cust_cfgs = pd->custom_configs; + if (cust_cfgs && is_custom_config_valid(cust_cfgs, dev)) { + temp = devm_kzalloc(dev, sizeof(*cust_cfgs), GFP_KERNEL); + if (temp) + memcpy(temp, cust_cfgs, sizeof(*cust_cfgs)); + pd->custom_configs = temp; + } + + /* + * Copy timings and min-tck values from platform data. If it is not + * available or if memory allocation fails, use JEDEC defaults + */ + size = sizeof(struct lpddr2_timings) * pd->timings_arr_size; + if (pd->timings) { + temp = devm_kzalloc(dev, size, GFP_KERNEL); + if (temp) { + memcpy(temp, pd->timings, size); + pd->timings = temp; + } else { + get_default_timings(emif); + } + } else { + get_default_timings(emif); + } + + if (pd->min_tck) { + temp = devm_kzalloc(dev, sizeof(*pd->min_tck), GFP_KERNEL); + if (temp) { + memcpy(temp, pd->min_tck, sizeof(*pd->min_tck)); + pd->min_tck = temp; + } else { + pd->min_tck = &lpddr2_jedec_min_tck; + } + } else { + pd->min_tck = &lpddr2_jedec_min_tck; + } + +out: + return emif; + +error: + return NULL; +} + +static int __init_or_module emif_probe(struct platform_device *pdev) +{ + struct emif_data *emif; + int irq, ret; + + if (pdev->dev.of_node) + emif = of_get_memory_device_details(pdev->dev.of_node, &pdev->dev); + else + emif = get_device_details(pdev); + + if (!emif) { + pr_err("%s: error getting device data\n", __func__); + goto error; + } + + list_add(&emif->node, &device_list); + + /* Save pointers to each other in emif and device structures */ + emif->dev = &pdev->dev; + platform_set_drvdata(pdev, emif); + + emif->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(emif->base)) + goto error; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + goto error; + + emif_onetime_settings(emif); + emif_debugfs_init(emif); + disable_and_clear_all_interrupts(emif); + ret = setup_interrupts(emif, irq); + if (ret) + goto error; + + /* One-time actions taken on probing the first device */ + if (!emif1) { + emif1 = emif; + + /* + * TODO: register notifiers for frequency and voltage + * change here once the respective frameworks are + * available + */ + } + + dev_info(&pdev->dev, "%s: device configured with addr = %p and IRQ%d\n", + __func__, emif->base, irq); + + return 0; +error: + return -ENODEV; +} + +static int __exit emif_remove(struct platform_device *pdev) +{ + struct emif_data *emif = platform_get_drvdata(pdev); + + emif_debugfs_exit(emif); + + return 0; +} + +static void emif_shutdown(struct platform_device *pdev) +{ + struct emif_data *emif = platform_get_drvdata(pdev); + + disable_and_clear_all_interrupts(emif); +} + +#if defined(CONFIG_OF) +static const struct of_device_id emif_of_match[] = { + { .compatible = "ti,emif-4d" }, + { .compatible = "ti,emif-4d5" }, + {}, +}; +MODULE_DEVICE_TABLE(of, emif_of_match); +#endif + +static struct platform_driver emif_driver = { + .remove = __exit_p(emif_remove), + .shutdown = emif_shutdown, + .driver = { + .name = "emif", + .of_match_table = of_match_ptr(emif_of_match), + }, +}; + +module_platform_driver_probe(emif_driver, emif_probe); + +MODULE_DESCRIPTION("TI EMIF SDRAM Controller Driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:emif"); +MODULE_AUTHOR("Texas Instruments Inc"); -- cgit v1.2.3