From 19fcec84d8d7d21e796c7624e521b60d28ee21ed Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:45:59 +0200 Subject: Adding upstream version 16.2.11+ds. Signed-off-by: Daniel Baumann --- doc/rados/configuration/msgr2.rst | 233 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 233 insertions(+) create mode 100644 doc/rados/configuration/msgr2.rst (limited to 'doc/rados/configuration/msgr2.rst') diff --git a/doc/rados/configuration/msgr2.rst b/doc/rados/configuration/msgr2.rst new file mode 100644 index 000000000..3415b1f5f --- /dev/null +++ b/doc/rados/configuration/msgr2.rst @@ -0,0 +1,233 @@ +.. _msgr2: + +Messenger v2 +============ + +What is it +---------- + +The messenger v2 protocol, or msgr2, is the second major revision on +Ceph's on-wire protocol. It brings with it several key features: + +* A *secure* mode that encrypts all data passing over the network +* Improved encapsulation of authentication payloads, enabling future + integration of new authentication modes like Kerberos +* Improved earlier feature advertisement and negotiation, enabling + future protocol revisions + +Ceph daemons can now bind to multiple ports, allowing both legacy Ceph +clients and new v2-capable clients to connect to the same cluster. + +By default, monitors now bind to the new IANA-assigned port ``3300`` +(ce4h or 0xce4) for the new v2 protocol, while also binding to the +old default port ``6789`` for the legacy v1 protocol. + +.. _address_formats: + +Address formats +--------------- + +Prior to Nautilus, all network addresses were rendered like +``1.2.3.4:567/89012`` where there was an IP address, a port, and a +nonce to uniquely identify a client or daemon on the network. +Starting with Nautilus, we now have three different address types: + +* **v2**: ``v2:1.2.3.4:578/89012`` identifies a daemon binding to a + port speaking the new v2 protocol +* **v1**: ``v1:1.2.3.4:578/89012`` identifies a daemon binding to a + port speaking the legacy v1 protocol. Any address that was + previously shown with any prefix is now shown as a ``v1:`` address. +* **TYPE_ANY** ``any:1.2.3.4:578/89012`` identifies a client that can + speak either version of the protocol. Prior to nautilus, clients would appear as + ``1.2.3.4:0/123456``, where the port of 0 indicates they are clients + and do not accept incoming connections. Starting with Nautilus, + these clients are now internally represented by a **TYPE_ANY** + address, and still shown with no prefix, because they may + connect to daemons using the v2 or v1 protocol, depending on what + protocol(s) the daemons are using. + +Because daemons now bind to multiple ports, they are now described by +a vector of addresses instead of a single address. For example, +dumping the monitor map on a Nautilus cluster now includes lines +like:: + + epoch 1 + fsid 50fcf227-be32-4bcb-8b41-34ca8370bd16 + last_changed 2019-02-25 11:10:46.700821 + created 2019-02-25 11:10:46.700821 + min_mon_release 14 (nautilus) + 0: [v2:10.0.0.10:3300/0,v1:10.0.0.10:6789/0] mon.foo + 1: [v2:10.0.0.11:3300/0,v1:10.0.0.11:6789/0] mon.bar + 2: [v2:10.0.0.12:3300/0,v1:10.0.0.12:6789/0] mon.baz + +The bracketed list or vector of addresses means that the same daemon can be +reached on multiple ports (and protocols). Any client or other daemon +connecting to that daemon will use the v2 protocol (listed first) if +possible; otherwise it will back to the legacy v1 protocol. Legacy +clients will only see the v1 addresses and will continue to connect as +they did before, with the v1 protocol. + +Starting in Nautilus, the ``mon_host`` configuration option and ``-m +`` command line options support the same bracketed address +vector syntax. + + +Bind configuration options +^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Two new configuration options control whether the v1 and/or v2 +protocol is used: + + * ``ms_bind_msgr1`` [default: true] controls whether a daemon binds + to a port speaking the v1 protocol + * ``ms_bind_msgr2`` [default: true] controls whether a daemon binds + to a port speaking the v2 protocol + +Similarly, two options control whether IPv4 and IPv6 addresses are used: + + * ``ms_bind_ipv4`` [default: true] controls whether a daemon binds + to an IPv4 address + * ``ms_bind_ipv6`` [default: false] controls whether a daemon binds + to an IPv6 address + +.. note:: The ability to bind to multiple ports has paved the way for + dual-stack IPv4 and IPv6 support. That said, dual-stack support is + not yet tested as of Nautilus v14.2.0 and likely needs some + additional code changes to work correctly. + +Connection modes +---------------- + +The v2 protocol supports two connection modes: + +* *crc* mode provides: + + - a strong initial authentication when the connection is established + (with cephx, mutual authentication of both parties with protection + from a man-in-the-middle or eavesdropper), and + - a crc32c integrity check to protect against bit flips due to flaky + hardware or cosmic rays + + *crc* mode does *not* provide: + + - secrecy (an eavesdropper on the network can see all + post-authentication traffic as it goes by) or + - protection from a malicious man-in-the-middle (who can deliberate + modify traffic as it goes by, as long as they are careful to + adjust the crc32c values to match) + +* *secure* mode provides: + + - a strong initial authentication when the connection is established + (with cephx, mutual authentication of both parties with protection + from a man-in-the-middle or eavesdropper), and + - full encryption of all post-authentication traffic, including a + cryptographic integrity check. + + In Nautilus, secure mode uses the `AES-GCM + `_ stream cipher, + which is generally very fast on modern processors (e.g., faster than + a SHA-256 cryptographic hash). + +Connection mode configuration options +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +For most connections, there are options that control which modes are used: + +* ``ms_cluster_mode`` is the connection mode (or permitted modes) used + for intra-cluster communication between Ceph daemons. If multiple + modes are listed, the modes listed first are preferred. +* ``ms_service_mode`` is a list of permitted modes for clients to use + when connecting to the cluster. +* ``ms_client_mode`` is a list of connection modes, in order of + preference, for clients to use (or allow) when talking to a Ceph + cluster. + +There are a parallel set of options that apply specifically to +monitors, allowing administrators to set different (usually more +secure) requirements on communication with the monitors. + +* ``ms_mon_cluster_mode`` is the connection mode (or permitted modes) + to use between monitors. +* ``ms_mon_service_mode`` is a list of permitted modes for clients or + other Ceph daemons to use when connecting to monitors. +* ``ms_mon_client_mode`` is a list of connection modes, in order of + preference, for clients or non-monitor daemons to use when + connecting to monitors. + + +Transitioning from v1-only to v2-plus-v1 +---------------------------------------- + +By default, ``ms_bind_msgr2`` is true starting with Nautilus 14.2.z. +However, until the monitors start using v2, only limited services will +start advertising v2 addresses. + +For most users, the monitors are binding to the default legacy port ``6789`` +for the v1 protocol. When this is the case, enabling v2 is as simple as: + +.. prompt:: bash $ + + ceph mon enable-msgr2 + +If the monitors are bound to non-standard ports, you will need to +specify an additional port for v2 explicitly. For example, if your +monitor ``mon.a`` binds to ``1.2.3.4:1111``, and you want to add v2 on +port ``1112``: + +.. prompt:: bash $ + + ceph mon set-addrs a [v2:1.2.3.4:1112,v1:1.2.3.4:1111] + +Once the monitors bind to v2, each daemon will start advertising a v2 +address when it is next restarted. + + +.. _msgr2_ceph_conf: + +Updating ceph.conf and mon_host +------------------------------- + +Prior to Nautilus, a CLI user or daemon will normally discover the +monitors via the ``mon_host`` option in ``/etc/ceph/ceph.conf``. The +syntax for this option has expanded starting with Nautilus to allow +support the new bracketed list format. For example, an old line +like:: + + mon_host = 10.0.0.1:6789,10.0.0.2:6789,10.0.0.3:6789 + +Can be changed to:: + + mon_host = [v2:10.0.0.1:3300/0,v1:10.0.0.1:6789/0],[v2:10.0.0.2:3300/0,v1:10.0.0.2:6789/0],[v2:10.0.0.3:3300/0,v1:10.0.0.3:6789/0] + +However, when default ports are used (``3300`` and ``6789``), they can +be omitted:: + + mon_host = 10.0.0.1,10.0.0.2,10.0.0.3 + +Once v2 has been enabled on the monitors, ``ceph.conf`` may need to be +updated to either specify no ports (this is usually simplest), or +explicitly specify both the v2 and v1 addresses. Note, however, that +the new bracketed syntax is only understood by Nautilus and later, so +do not make that change on hosts that have not yet had their ceph +packages upgraded. + +When you are updating ``ceph.conf``, note the new ``ceph config +generate-minimal-conf`` command (which generates a barebones config +file with just enough information to reach the monitors) and the +``ceph config assimilate-conf`` (which moves config file options into +the monitors' configuration database) may be helpful. For example,:: + + # ceph config assimilate-conf < /etc/ceph/ceph.conf + # ceph config generate-minimal-config > /etc/ceph/ceph.conf.new + # cat /etc/ceph/ceph.conf.new + # minimal ceph.conf for 0e5a806b-0ce5-4bc6-b949-aa6f68f5c2a3 + [global] + fsid = 0e5a806b-0ce5-4bc6-b949-aa6f68f5c2a3 + mon_host = [v2:10.0.0.1:3300/0,v1:10.0.0.1:6789/0] + # mv /etc/ceph/ceph.conf.new /etc/ceph/ceph.conf + +Protocol +-------- + +For a detailed description of the v2 wire protocol, see :ref:`msgr2-protocol`. -- cgit v1.2.3