.. highlight:: console ``kxdpgun`` – DNS benchmarking tool =================================== Synopsis -------- :program:`kxdpgun` [*options*] **-i** *filename* *targetIP* Description ----------- Powerful generator of DNS traffic, sending and receiving packets through XDP. Queries are generated according to a textual file which is read sequentially in a loop until a configured duration elapses. The order of queries is not guaranteed. Responses are received (unless disabled) and counted, but not checked against queries. The number of parallel threads is autodetected according to the number of queues configured for the network interface. Options ....... **-t**, **--duration** *seconds* Duration of traffic generation, specified as a decimal number in seconds (default is 5.0). **-T**, **--tcp**\[\ **=**\ *debug_mode*\] Send queries over TCP. See the list of optional debug modes below. **-U**, **--quic**\[\ **=**\ *debug_mode*\] Send queries over QUIC. See the list of optional debug modes below. **-Q**, **--qps** *queries* Number of queries-per-second (approximately) to be sent (default is 1000). The program is not optimized for low speeds at which it may lose communication packets. The recommended minimum speed is 2 packets per thread (Rx/Tx queue). **-b**, **--batch** *size* Send more queries in a batch. Improves QPS but may affect the counterpart's packet loss (default is 10 for UDP and 1 for TCP/QUIC). **-r**, **--drop** Drop incoming responses. Improves QPS, but disables response statistics. **-p**, **--port** *number* Remote destination port (default is 53 for UDP/TCP, 853 for QUIC). **-F**, **--affinity** *cpu_spec* CPU affinity for all threads specified in the format [][s], where is the CPU ID for the first thread and is the CPU ID increment for next thread (default is 0s1). **-i**, **--infile** *filename* Path to a file with query templates. **-I**, **--interface** *interface* Network interface for outgoing communication. This can be useful in situations when the interfaces are in a bond for example. **-l**, **--local** *localIP*\ [**/**\ *prefix*] Override the auto-detected source IP address. If an address range is specified instead, various IPs from the range will be used for different queries uniformly (address range not supported in the QUIC mode). *targetIP* The IPv4 or IPv6 address of remote destination. **-L**, **--mac-local** Override auto-detected local MAC address. **-R**, **--mac-remote** Override auto-detected remote MAC address. **-v**, **--vlan** *id* Add VLAN 802.1Q header with the given id. VLAN offloading should be disabled. **-h**, **--help** Print the program help. **-V**, **--version** Print the program version. Queries file format ................... Each line describes a query in the form: *query_name* *query_type* [*flags*] Where *query_name* is a domain name to be queried, *query_type* is a record type name, and *flags* is a single character: **E** Send query with EDNS. **D** Request DNSSEC (EDNS + DO flag). TCP/QUIC debug modes .................... **0** Perform full handshake for all connections (QUIC only). **1** Just send SYN (Initial) and receive SYN-ACK (Handshake). **2** Perform TCP/QUIC handshake and don't send anything, allow close initiated by counterpart. **3** Perform TCP/QUIC handshake and don't react further. **5** Send incomplete query (N-1 bytes) and don't react further. **7** Send query and don't ACK the response or anything further. **8** Don't close the connection and ignore close by counterpart (TCP only). **9** Operate normally except for not ACKing the final FIN+ACK (TCP only). Signals ....... Sending USR1 signal to a running process triggers current statistics dump to the standard output. Notes ----- Linux kernel 4.18+ is required. The utility has to be executed under root or with these capabilities: CAP_NET_RAW, CAP_NET_ADMIN, CAP_SYS_ADMIN, CAP_IPC_LOCK, and CAP_SYS_RESOURCE (Linux < 5.11). The utility allocates source UDP/TCP ports from the range 2000-65535. Exit values ----------- Exit status of 0 means successful operation. Any other exit status indicates an error. Examples -------- Manually created queries file:: abc6.example.com. AAAA nxdomain.example.com. A notzone. A a.example.com. NS E ab.example.com. A D abcd.example.com. DS D Queries file generated from a zone file (Knot DNS format):: cat ZONE_FILE | awk "{print \$1,\$3}" | grep -E "(NS|DS|A|AAAA|PTR|MX|SOA)$" | sort -u -R > queries.txt Basic usage:: # kxdpgun -i ~/queries.txt 2001:DB8::1 *Using UDP with increased batch size*:: # kxdpgun -t 20 -Q 1000000 -i ~/queries.txt -b 20 -p 8853 192.0.2.1 *Using TCP*:: # kxdpgun -t 20 -Q 100000 -i ~/queries.txt -T -p 8853 192.0.2.1 See Also -------- :manpage:`kdig(1)`.