diff options
Diffstat (limited to '')
| -rw-r--r-- | include/basegfx/polygon/b2dlinegeometry.hxx | 147 |
1 files changed, 147 insertions, 0 deletions
diff --git a/include/basegfx/polygon/b2dlinegeometry.hxx b/include/basegfx/polygon/b2dlinegeometry.hxx new file mode 100644 index 000000000..e12dd7498 --- /dev/null +++ b/include/basegfx/polygon/b2dlinegeometry.hxx @@ -0,0 +1,147 @@ +/* -*- Mode: C++; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*- */ +/* + * This file is part of the LibreOffice project. + * + * This Source Code Form is subject to the terms of the Mozilla Public + * License, v. 2.0. If a copy of the MPL was not distributed with this + * file, You can obtain one at http://mozilla.org/MPL/2.0/. + * + * This file incorporates work covered by the following license notice: + * + * Licensed to the Apache Software Foundation (ASF) under one or more + * contributor license agreements. See the NOTICE file distributed + * with this work for additional information regarding copyright + * ownership. The ASF licenses this file to you under the Apache + * License, Version 2.0 (the "License"); you may not use this file + * except in compliance with the License. You may obtain a copy of + * the License at http://www.apache.org/licenses/LICENSE-2.0 . + */ + +#pragma once + +#include <basegfx/numeric/ftools.hxx> +#include <basegfx/polygon/b2dpolypolygon.hxx> +#include <basegfx/polygon/b2dpolygon.hxx> +#include <com/sun/star/drawing/LineCap.hpp> +#include <basegfx/basegfxdllapi.h> +#include <basegfx/polygon/b2dpolygontriangulator.hxx> + +namespace basegfx::utils +{ + /** Create line start/end geometry element, mostly arrows and things like that. + + @param rCandidate + The polygon which needs to get that line ends and needs to have two points + at least. + + @param rArrow + The line start/end geometry. It is assumed that the tip is pointing + upwards. Result will be rotated and scaled to fit. + + @param bStart + describes if creation is for start or end of candidate. + + @param fWidth + defines the size of the element, it's describing the target width in X + of the arrow. + + @param fDockingPosition needs to be in [0.0 ..1.0] range, where 0.0 means + that the tip of the arrow will be aligned with the polygon start, 1.0 means + the bottom. The default of 0.5 describes a centered arrow. + + @param pConsumedLength + Using this parameter it is possible to get back how much from the candidate + geometry is overlapped by the created element (consumed). + + @param fCandidateLength + This should contain the length of rCandidate to allow work without + again calculating the length (which may be expensive with beziers). If 0.0 is + given, the length is calculated on demand. + + @param fShift + When it is necessary to count with the thickness of the line, it + makes sense to move the start position slightly - so define the shift. + + @return + The Line start and end polygon, correctly rotated and scaled + */ + BASEGFX_DLLPUBLIC B2DPolyPolygon createAreaGeometryForLineStartEnd( + const B2DPolygon& rCandidate, + const B2DPolyPolygon& rArrow, + bool bStart, + double fWidth, + double fCandidateLength, // 0.0 -> calculate self + double fDockingPosition, // 0->top, 1->bottom + double* pConsumedLength = nullptr, + double fShift = 0.0); + + /** create filled polygon geometry for lines with a line width + + This method will create bezier based, fillable polygons which + will resample the curve if it was extended for the given half + line width. It will remove extrema positions from contained + bezier segments and get as close as possible and defined by + the given parameters to the ideal result. + + It will check edges for trivial bezier to avoid unnecessary + bezier polygons. Care is taken to produce the in-between + polygon points (the ones original on the source polygon) since + it has showed that without those, the raster converters leave + non-filled gaps. + + @param rCandidate + The source polygon defining the hairline polygon path + + @param fHalfLineWidth + The width of the line to one side + + @param eJoin + The LineJoin if the edges meeting in a point do not have a C1 + or C2 continuity + + @param eCap + The kind of cap, which is added to the line. + + @param fMaxAllowedAngle + Allows to hand over the maximum allowed angle between an edge and + it's control vectors. The smaller, the more subdivisions will be + needed to create the filled geometry. Allowed range is cropped to + [M_PI_2 .. 0.01 * M_PI_2]. + + @param fMaxPartOfEdge + Allows to influence from with relative length of a control vector + compared to its edge a split is forced. The smaller, the more + subdivisions will be needed to create the filled geometry. Allowed + range is cropped to [1.0 .. 0.01] + + @param fMiterMinimumAngle + The minimum wanted angle between two edges when edge rounding + is using miter. When an edge is smaller than this (tighter) + the usual fallback to bevel is used. Allowed range is cropped + to [M_PI .. 0.01 * M_PI]. + + Commit 51b5b93092d6231615de470c62494c24e54828a1 needs + revert, we need the triangulation for X11 fat line drawing + + @param pTriangles + If given, the method will additionally add the created geometry as + B2DTriangle's + + @return + The tools::PolyPolygon containing the geometry of the extended line by + it's line width. Contains bezier segments and edge roundings as + needed and defined. + */ + BASEGFX_DLLPUBLIC B2DPolyPolygon createAreaGeometry( + const B2DPolygon& rCandidate, + double fHalfLineWidth, + B2DLineJoin eJoin, + css::drawing::LineCap eCap, + double fMaxAllowedAngle = basegfx::deg2rad(12.5), + double fMaxPartOfEdge = 0.4, + double fMiterMinimumAngle = basegfx::deg2rad(15.0), + basegfx::triangulator::B2DTriangleVector* pTriangles = nullptr); + +} // end of namespace basegfx::utils + +/* vim:set shiftwidth=4 softtabstop=4 expandtab: */ |