Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 226 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml b/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
new file mode 100644
index 000000000..7356084a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
@@ -0,0 +1,226 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/cirrus,cs42l42.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic CS42L42 audio CODEC
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description:
+  The CS42L42 is a low-power audio codec designed for portable applications.
+  It provides a high-dynamic range, stereo DAC for audio playback and a mono
+  high-dynamic-range ADC for audio capture. There is an integrated headset
+  detection block.
+
+properties:
+  compatible:
+    enum:
+      - cirrus,cs42l42
+      - cirrus,cs42l83
+
+  reg:
+    description:
+      The I2C address of the CS42L42.
+    maxItems: 1
+
+  VP-supply:
+    description:
+      VP power supply.
+
+  VCP-supply:
+    description:
+      Charge pump power supply.
+
+  VD_FILT-supply:
+    description:
+      FILT+ power supply.
+
+  VL-supply:
+    description:
+      Logic power supply.
+
+  VA-supply:
+    description:
+      Analog power supply.
+
+  reset-gpios:
+    description:
+      This pin will be asserted and then deasserted to reset the
+      CS42L42 before communication starts.
+    maxItems: 1
+
+  interrupts:
+    description:
+      Interrupt for CS42L42 IRQ line.
+    maxItems: 1
+
+  cirrus,ts-inv:
+    description: |
+      Sets the behaviour of the jack plug detect switch.
+
+      0 - (Default) Shorted to tip when unplugged, open when plugged.
+      This is "inverted tip sense (ITS)" in the datasheet.
+
+      1 - Open when unplugged, shorted to tip when plugged.
+      This is "normal tip sense (TS)" in the datasheet.
+
+      The CS42L42_TS_INV_* defines are available for this.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 1
+
+  cirrus,ts-dbnc-rise:
+    description: |
+      Debounce the rising edge of TIP_SENSE_PLUG. With no
+      debounce, the tip sense pin might be noisy on a plug event.
+
+      0 - 0ms
+      1 - 125ms
+      2 - 250ms
+      3 - 500ms
+      4 - 750ms
+      5 - 1s (Default)
+      6 - 1.25s
+      7 - 1.5s
+
+      The CS42L42_TS_DBNCE_* defines are available for this.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 7
+
+  cirrus,ts-dbnc-fall:
+    description: |
+      Debounce the falling edge of TIP_SENSE_UNPLUG. With no
+      debounce, the tip sense pin might be noisy on an unplug event.
+
+      0 - 0ms
+      1 - 125ms
+      2 - 250ms
+      3 - 500ms
+      4 - 750ms
+      5 - 1s (Default)
+      6 - 1.25s
+      7 - 1.5s
+
+      The CS42L42_TS_DBNCE_* defines are available for this.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 7
+
+  cirrus,btn-det-init-dbnce:
+    description: |
+      This sets how long to wait after enabling button detection
+      interrupts before servicing button interrupts, to allow the
+      HS bias time to settle. Value is in milliseconds.
+      There may be erroneous button interrupts if this debounce time
+      is too short.
+
+      0ms - 200ms,
+      Default = 100ms
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 200
+
+  cirrus,btn-det-event-dbnce:
+    description: |
+      This sets how long to wait after receiving a button press
+      interrupt before processing it. Allows time for the button
+      press to make a clean connection with the bias resistors.
+      Value is in milliseconds.
+
+      0ms - 20ms,
+      Default = 10ms
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 20
+
+  cirrus,bias-lvls:
+    description: |
+      For a level-detect headset button scheme, each button will bias
+      the mic pin to a certain voltage. To determine which button was
+      pressed, the voltage is compared to sequential, decreasing
+      voltages, until the compared voltage < bias voltage.
+      For different hardware setups, a designer might want to tweak this.
+      This is an array of descending values for the comparator voltage,
+      given as percent of the HSBIAS voltage.
+
+      Array of 4 values, each 0-63
+      < x1 x2 x3 x4 >
+      Default = < 15 8 4 1 >
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 4
+    maxItems: 4
+    items:
+      minimum: 0
+      maximum: 63
+
+  cirrus,hs-bias-ramp-rate:
+    description: |
+      If present this sets the rate that the HS bias should rise and fall.
+      The actual rise and fall times depend on external hardware (the
+      datasheet gives several rise and fall time examples).
+
+      0 - Fast rise time; slow, load-dependent fall time
+      1 - Fast
+      2 - Slow (default)
+      3 - Slowest
+
+      The CS42L42_HSBIAS_RAMP_* defines are available for this.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 3
+
+  cirrus,hs-bias-sense-disable:
+    description: |
+      If present the HSBIAS sense is disabled. Configures HSBIAS output
+      current sense through the external 2.21-k resistor. HSBIAS_SENSE
+      is a hardware feature to reduce the potential pop noise when the
+      headset plug is removed slowly. But on some platforms ESD voltage
+      will affect it causing plug detection to fail, especially with CTIA
+      headset type. For different hardware setups, a designer might want
+      to tweak default behavior.
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - VP-supply
+  - VCP-supply
+  - VD_FILT-supply
+  - VL-supply
+  - VA-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/sound/cs42l42.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      cs42l42: cs42l42@48 {
+          compatible = "cirrus,cs42l42";
+          reg = <0x48>;
+          VA-supply = <&dummy_vreg>;
+          VP-supply = <&dummy_vreg>;
+          VCP-supply = <&dummy_vreg>;
+          VD_FILT-supply = <&dummy_vreg>;
+          VL-supply = <&dummy_vreg>;
+
+          reset-gpios = <&axi_gpio_0 1 0>;
+          interrupt-parent = <&gpio0>;
+          interrupts = <55 8>;
+
+          cirrus,ts-inv = <CS42L42_TS_INV_DIS>;
+          cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>;
+          cirrus,ts-dbnc-fall = <CS42L42_TS_DBNCE_0>;
+          cirrus,btn-det-init-dbnce = <100>;
+          cirrus,btn-det-event-dbnce = <10>;
+          cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>;
+          cirrus,hs-bias-ramp-rate = <CS42L42_HSBIAS_RAMP_SLOW>;
+      };
+    };