diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-07 18:49:45 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-07 18:49:45 +0000 |
commit | 2c3c1048746a4622d8c89a29670120dc8fab93c4 (patch) | |
tree | 848558de17fb3008cdf4d861b01ac7781903ce39 /Documentation/driver-api/usb/error-codes.rst | |
parent | Initial commit. (diff) | |
download | linux-upstream.tar.xz linux-upstream.zip |
Adding upstream version 6.1.76.upstream/6.1.76upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/driver-api/usb/error-codes.rst | 210 |
1 files changed, 210 insertions, 0 deletions
diff --git a/Documentation/driver-api/usb/error-codes.rst b/Documentation/driver-api/usb/error-codes.rst new file mode 100644 index 000000000..8f9790c2d --- /dev/null +++ b/Documentation/driver-api/usb/error-codes.rst @@ -0,0 +1,210 @@ +.. _usb-error-codes: + +USB Error codes +~~~~~~~~~~~~~~~ + +:Revised: 2004-Oct-21 + +This is the documentation of (hopefully) all possible error codes (and +their interpretation) that can be returned from usbcore. + +Some of them are returned by the Host Controller Drivers (HCDs), which +device drivers only see through usbcore. As a rule, all the HCDs should +behave the same except for transfer speed dependent behaviors and the +way certain faults are reported. + + +Error codes returned by :c:func:`usb_submit_urb` +================================================ + +Non-USB-specific: + + +=============== =============================================== +0 URB submission went fine + +``-ENOMEM`` no memory for allocation of internal structures +=============== =============================================== + +USB-specific: + +======================= ======================================================= +``-EBUSY`` The URB is already active. + +``-ENODEV`` specified USB-device or bus doesn't exist + +``-ENOENT`` specified interface or endpoint does not exist or + is not enabled + +``-ENXIO`` host controller driver does not support queuing of + this type of urb. (treat as a host controller bug.) + +``-EINVAL`` a) Invalid transfer type specified (or not supported) + b) Invalid or unsupported periodic transfer interval + c) ISO: attempted to change transfer interval + d) ISO: ``number_of_packets`` is < 0 + e) various other cases + +``-EXDEV`` ISO: ``URB_ISO_ASAP`` wasn't specified and all the + frames the URB would be scheduled in have already + expired. + +``-EFBIG`` Host controller driver can't schedule that many ISO + frames. + +``-EPIPE`` The pipe type specified in the URB doesn't match the + endpoint's actual type. + +``-EMSGSIZE`` (a) endpoint maxpacket size is zero; it is not usable + in the current interface altsetting. + (b) ISO packet is larger than the endpoint maxpacket. + (c) requested data transfer length is invalid: negative + or too large for the host controller. + +``-EBADR`` The wLength value in a control URB's setup packet does + not match the URB's transfer_buffer_length. + +``-ENOSPC`` This request would overcommit the usb bandwidth reserved + for periodic transfers (interrupt, isochronous). + +``-ESHUTDOWN`` The device or host controller has been disabled due to + some problem that could not be worked around. + +``-EPERM`` Submission failed because ``urb->reject`` was set. + +``-EHOSTUNREACH`` URB was rejected because the device is suspended. + +``-ENOEXEC`` A control URB doesn't contain a Setup packet. +======================= ======================================================= + +Error codes returned by ``in urb->status`` or in ``iso_frame_desc[n].status`` (for ISO) +======================================================================================= + +USB device drivers may only test urb status values in completion handlers. +This is because otherwise there would be a race between HCDs updating +these values on one CPU, and device drivers testing them on another CPU. + +A transfer's actual_length may be positive even when an error has been +reported. That's because transfers often involve several packets, so that +one or more packets could finish before an error stops further endpoint I/O. + +For isochronous URBs, the urb status value is non-zero only if the URB is +unlinked, the device is removed, the host controller is disabled, or the total +transferred length is less than the requested length and the +``URB_SHORT_NOT_OK`` flag is set. Completion handlers for isochronous URBs +should only see ``urb->status`` set to zero, ``-ENOENT``, ``-ECONNRESET``, +``-ESHUTDOWN``, or ``-EREMOTEIO``. Individual frame descriptor status fields +may report more status codes. + + +=============================== =============================================== +0 Transfer completed successfully + +``-ENOENT`` URB was synchronously unlinked by + :c:func:`usb_unlink_urb` + +``-EINPROGRESS`` URB still pending, no results yet + (That is, if drivers see this it's a bug.) + +``-EPROTO`` [#f1]_, [#f2]_ a) bitstuff error + b) no response packet received within the + prescribed bus turn-around time + c) unknown USB error + +``-EILSEQ`` [#f1]_, [#f2]_ a) CRC mismatch + b) no response packet received within the + prescribed bus turn-around time + c) unknown USB error + + Note that often the controller hardware does + not distinguish among cases a), b), and c), so + a driver cannot tell whether there was a + protocol error, a failure to respond (often + caused by device disconnect), or some other + fault. + +``-ETIME`` [#f2]_ No response packet received within the + prescribed bus turn-around time. This error + may instead be reported as + ``-EPROTO`` or ``-EILSEQ``. + +``-ETIMEDOUT`` Synchronous USB message functions use this code + to indicate timeout expired before the transfer + completed, and no other error was reported + by HC. + +``-EPIPE`` [#f2]_ Endpoint stalled. For non-control endpoints, + reset this status with + :c:func:`usb_clear_halt`. + +``-ECOMM`` During an IN transfer, the host controller + received data from an endpoint faster than it + could be written to system memory + +``-ENOSR`` During an OUT transfer, the host controller + could not retrieve data from system memory fast + enough to keep up with the USB data rate + +``-EOVERFLOW`` [#f1]_ The amount of data returned by the endpoint was + greater than either the max packet size of the + endpoint or the remaining buffer size. + "Babble". + +``-EREMOTEIO`` The data read from the endpoint did not fill + the specified buffer, and ``URB_SHORT_NOT_OK`` + was set in ``urb->transfer_flags``. + +``-ENODEV`` Device was removed. Often preceded by a burst + of other errors, since the hub driver doesn't + detect device removal events immediately. + +``-EXDEV`` ISO transfer only partially completed + (only set in ``iso_frame_desc[n].status``, + not ``urb->status``) + +``-EINVAL`` ISO madness, if this happens: Log off and + go home + +``-ECONNRESET`` URB was asynchronously unlinked by + :c:func:`usb_unlink_urb` + +``-ESHUTDOWN`` The device or host controller has been + disabled due to some problem that could not + be worked around, such as a physical + disconnect. +=============================== =============================================== + + +.. [#f1] + + Error codes like ``-EPROTO``, ``-EILSEQ`` and ``-EOVERFLOW`` normally + indicate hardware problems such as bad devices (including firmware) + or cables. + +.. [#f2] + + This is also one of several codes that different kinds of host + controller use to indicate a transfer has failed because of device + disconnect. In the interval before the hub driver starts disconnect + processing, devices may receive such fault reports for every request. + + + +Error codes returned by usbcore-functions +========================================= + +.. note:: expect also other submit and transfer status codes + +:c:func:`usb_register`: + +======================= =================================== +``-EINVAL`` error during registering new driver +======================= =================================== + +``usb_get_*/usb_set_*()``, +:c:func:`usb_control_msg`, +:c:func:`usb_bulk_msg()`: + +======================= ============================================== +``-ETIMEDOUT`` Timeout expired before the transfer completed. +======================= ============================================== |