Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 497 insertions, 0 deletions

diff --git a/arch/powerpc/boot/dts/turris1x.dts b/arch/powerpc/boot/dts/turris1x.dts
new file mode 100644
index 000000000..9377055d5
--- /dev/null
+++ b/arch/powerpc/boot/dts/turris1x.dts
@@ -0,0 +1,497 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Turris 1.x Device Tree Source
+ *
+ * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/)
+ *
+ * Pinout, Schematics and Altium hardware design files are open source
+ * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+/include/ "fsl/p2020si-pre.dtsi"
+
+/ {
+	model = "Turris 1.x";
+	compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		spi0 = &spi0;
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	soc: soc@ffe00000 {
+		ranges = <0x0 0x0 0xffe00000 0x00100000>;
+
+		i2c@3000 {
+			/* PCA9557PW GPIO controller for boot config */
+			gpio-controller@18 {
+				compatible = "nxp,pca9557";
+				label = "bootcfg";
+				reg = <0x18>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				polarity = <0x00>;
+			};
+
+			/* STM32F030R8T6 MCU for power control */
+			power-control@2a {
+				/*
+				 * Turris Power Control firmware runs on STM32F0 MCU.
+				 * This firmware is open source and available at:
+				 * https://gitlab.nic.cz/turris/hw/turris_power_control
+				 */
+				reg = <0x2a>;
+			};
+
+			/* DDR3 SPD/EEPROM PSWP instruction */
+			eeprom@32 {
+				reg = <0x32>;
+			};
+
+			/* SA56004ED temperature control */
+			temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */
+					     <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* Local temperature sensor (SA56004ED internal) */
+				channel@0 {
+					reg = <0>;
+					label = "board";
+				};
+
+				/* Remote temperature sensor (D+/D- connected to P2020 CPU Temperature Diode) */
+				channel@1 {
+					reg = <1>;
+					label = "cpu";
+				};
+			};
+
+			/* DDR3 SPD/EEPROM */
+			eeprom@52 {
+				compatible = "atmel,spd";
+				reg = <0x52>;
+			};
+
+			/* MCP79402-I/ST Protected EEPROM */
+			eeprom@57 {
+				reg = <0x57>;
+			};
+
+			/* ATSHA204-TH-DA-T crypto module */
+			crypto@64 {
+				compatible = "atmel,atsha204";
+				reg = <0x64>;
+			};
+
+			/* IDT6V49205BNLGI clock generator */
+			clock-generator@69 {
+				compatible = "idt,6v49205b";
+				reg = <0x69>;
+			};
+
+			/* MCP79402-I/ST RTC */
+			rtc@6f {
+				compatible = "microchip,mcp7940x";
+				reg = <0x6f>;
+				interrupt-parent = <&gpio>;
+				interrupts = <14 0>; /* GPIO14 - MFP pin */
+			};
+		};
+
+		/* SPI on connector P1 */
+		spi0: spi@7000 {
+		};
+
+		gpio: gpio-controller@fc00 {
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		/* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */
+		usb@22000 {
+			phy_type = "ulpi";
+			dr_mode = "host";
+		};
+
+		enet0: ethernet@24000 {
+			/* Connected to port 6 of QCA8337N-AL3C switch */
+			phy-connection-type = "rgmii-id";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		mdio@24520 {
+			/* KSZ9031RNXCA ethernet phy for WAN port */
+			phy: ethernet-phy@7 {
+				interrupts = <3 1 0 0>;
+				reg = <0x7>;
+			};
+
+			/* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */
+			switch@10 {
+				compatible = "qca,qca8337";
+				interrupts = <2 1 0 0>;
+				reg = <0x10>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						label = "cpu";
+						ethernet = <&enet1>;
+						phy-mode = "rgmii-id";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan5";
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan4";
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan3";
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan2";
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan1";
+					};
+
+					port@6 {
+						reg = <6>;
+						label = "cpu";
+						ethernet = <&enet0>;
+						phy-mode = "rgmii-id";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+		};
+
+		ptp_clock@24e00 {
+			fsl,tclk-period = <5>;
+			fsl,tmr-prsc = <200>;
+			fsl,tmr-add = <0xcccccccd>;
+			fsl,tmr-fiper1 = <0x3b9ac9fb>;
+			fsl,tmr-fiper2 = <0x0001869b>;
+			fsl,max-adj = <249999999>;
+		};
+
+		enet1: ethernet@25000 {
+			/* Connected to port 0 of QCA8337N-AL3C switch */
+			phy-connection-type = "rgmii-id";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		mdio@25520 {
+			status = "disabled";
+		};
+
+		enet2: ethernet@26000 {
+			/* Connected to KSZ9031RNXCA ethernet phy (WAN port) */
+			label = "wan";
+			phy-handle = <&phy>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		mdio@26520 {
+			status = "disabled";
+		};
+
+		sdhc@2e000 {
+			bus-width = <4>;
+			cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	lbc: localbus@ffe05000 {
+		reg = <0 0xffe05000 0 0x1000>;
+
+		ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */
+			 <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */
+			 <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */
+
+		/* S29GL128P90TFIR10 NOR */
+		nor@0,0 {
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x01000000>;
+			bank-width = <2>;
+			device-width = <1>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					/* 128 kB for Device Tree Blob */
+					reg = <0x00000000 0x00020000>;
+					label = "dtb";
+				};
+
+				partition@20000 {
+					/* 1.7 MB for Linux Kernel Image */
+					reg = <0x00020000 0x001a0000>;
+					label = "kernel";
+				};
+
+				partition@1c0000 {
+					/* 1.5 MB for Rescue JFFS2 Root File System */
+					reg = <0x001c0000 0x00180000>;
+					label = "rescue";
+				};
+
+				partition@340000 {
+					/* 11 MB for TAR.XZ Archive with Factory content of NAND Root File System */
+					reg = <0x00340000 0x00b00000>;
+					label = "factory";
+				};
+
+				partition@e40000 {
+					/* 768 kB for Certificates JFFS2 File System */
+					reg = <0x00e40000 0x000c0000>;
+					label = "certificates";
+				};
+
+				/* free unused space 0x00f00000-0x00f20000 */
+
+				partition@f20000 {
+					/* 128 kB for U-Boot Environment Variables */
+					reg = <0x00f20000 0x00020000>;
+					label = "u-boot-env";
+				};
+
+				partition@f40000 {
+					/* 768 kB for U-Boot Bootloader Image */
+					reg = <0x00f40000 0x000c0000>;
+					label = "u-boot";
+				};
+			};
+		};
+
+		/* MT29F2G08ABAEAWP:E NAND */
+		nand@1,0 {
+			compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand";
+			reg = <0x1 0x0 0x00040000>;
+			nand-ecc-mode = "soft";
+			nand-ecc-algo = "bch";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					/* 256 MB for UBI with one volume: UBIFS Root File System */
+					reg = <0x00000000 0x10000000>;
+					label = "rootfs";
+				};
+			};
+		};
+
+		/* LCMXO1200C-3FTN256C FPGA */
+		cpld@3,0 {
+			/*
+			 * Turris CPLD firmware which runs on this Lattice FPGA,
+			 * is extended version of P1021RDB-PC CPLD v4.1 firmware.
+			 * It is backward compatible with its original version
+			 * and the only extension is support for Turris LEDs.
+			 * Turris CPLD firmware is open source and available at:
+			 * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
+			 */
+			compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus", "syscon";
+			reg = <0x3 0x0 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x3 0x0 0x00020000>;
+
+			/* MAX6370KA+T watchdog */
+			watchdog@2 {
+				/*
+				 * CPLD firmware maps SET0, SET1 and SET2
+				 * input logic of MAX6370KA+T chip to CPLD
+				 * memory space at byte offset 0x2. WDI
+				 * input logic is outside of the CPLD and
+				 * connected via external GPIO.
+				 */
+				compatible = "maxim,max6370";
+				reg = <0x02 0x01>;
+				gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+			};
+
+			reboot@d {
+				compatible = "syscon-reboot";
+				reg = <0x0d 0x01>;
+				offset = <0x0d>;
+				mask = <0x01>;
+				value = <0x01>;
+			};
+
+			led-controller@13 {
+				/*
+				 * LEDs are controlled by CPLD firmware.
+				 * All five LAN LEDs share common RGB settings
+				 * and so it is not possible to set different
+				 * colors on different LAN ports.
+				 */
+				compatible = "cznic,turris1x-leds";
+				reg = <0x13 0x1d>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				multi-led@0 {
+					reg = <0x0>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WAN;
+				};
+
+				multi-led@1 {
+					reg = <0x1>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <5>;
+				};
+
+				multi-led@2 {
+					reg = <0x2>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <4>;
+				};
+
+				multi-led@3 {
+					reg = <0x3>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <3>;
+				};
+
+				multi-led@4 {
+					reg = <0x4>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <2>;
+				};
+
+				multi-led@5 {
+					reg = <0x5>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <1>;
+				};
+
+				multi-led@6 {
+					reg = <0x6>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WLAN;
+				};
+
+				multi-led@7 {
+					reg = <0x7>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_POWER;
+				};
+			};
+		};
+	};
+
+	pci2: pcie@ffe08000 {
+		/*
+		 * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller.
+		 * This xHCI controller is available only on Turris 1.1 boards.
+		 * Turris 1.0 boards have nothing connected to this PCIe bus,
+		 * so system would see only PCIe Root Port of this PCIe Root
+		 * Complex. TUSB7340RKM xHCI controller has four SuperSpeed
+		 * channels. Channel 0 is connected to the front USB 3.0 port,
+		 * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe
+		 * slot 1 (CN5), channels 2 and 3 to connector P600.
+		 *
+		 * P2020 PCIe Root Port does not use PCIe MEM and xHCI controller
+		 * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required.
+		 * So allocate 128kB of PCIe MEM for this PCIe bus.
+		 */
+		reg = <0 0xffe08000 0 0x1000>;
+		ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00020000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+
+	pci1: pcie@ffe09000 {
+		/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
+		reg = <0 0xffe09000 0 0x1000>;
+		ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+
+	pci0: pcie@ffe0a000 {
+		/*
+		 * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card.
+		 * Turris 1.1 boards have in this mPCIe slot additional USB 2.0
+		 * pins via channel 1 of TUSB7340RKM xHCI controller and also
+		 * additional SIM card slot, both for USB-based WWAN cards.
+		 */
+		reg = <0 0xffe0a000 0 0x1000>;
+		ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */
+			 <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */
+
+		pcie@0 {
+			ranges;
+		};
+	};
+};
+
+/include/ "fsl/p2020si-post.dtsi"