Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 629 insertions, 0 deletions

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
new file mode 100644
index 000000000..617c95522
--- /dev/null
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Libata driver for the HighPoint 371N, 372N, and 302N UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
+ *
+ * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003		Red Hat Inc
+ * Portions Copyright (C) 2005-2010	MontaVista Software, Inc.
+ *
+ *
+ * TODO
+ *	Work out best PLL policy
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"pata_hpt3x2n"
+#define DRV_VERSION	"0.3.19"
+
+enum {
+	PCI66		=	(1 << 1),
+	USE_DPLL	=	(1 << 0)
+};
+
+struct hpt_clock {
+	u8	xfer_speed;
+	u32	timing;
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 4:8    data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 9:12   cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. Active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:20  udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21     CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24  pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27  cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
+ *        register access.
+ * 28     UDMA enable.
+ * 29     DMA  enable.
+ * 30     PIO_MST enable. If set, the chip is in bus master mode during
+ *        PIO xfer.
+ * 31     FIFO enable. Only for PIO.
+ */
+
+/* 66MHz DPLL clocks */
+
+static struct hpt_clock hpt3x2n_clocks[] = {
+	{	XFER_UDMA_7,	0x1c869c62	},
+	{	XFER_UDMA_6,	0x1c869c62	},
+	{	XFER_UDMA_5,	0x1c8a9c62	},
+	{	XFER_UDMA_4,	0x1c8a9c62	},
+	{	XFER_UDMA_3,	0x1c8e9c62	},
+	{	XFER_UDMA_2,	0x1c929c62	},
+	{	XFER_UDMA_1,	0x1c9a9c62	},
+	{	XFER_UDMA_0,	0x1c829c62	},
+
+	{	XFER_MW_DMA_2,	0x2c829c62	},
+	{	XFER_MW_DMA_1,	0x2c829c66	},
+	{	XFER_MW_DMA_0,	0x2c829d2e	},
+
+	{	XFER_PIO_4,	0x0c829c62	},
+	{	XFER_PIO_3,	0x0c829c84	},
+	{	XFER_PIO_2,	0x0c829ca6	},
+	{	XFER_PIO_1,	0x0d029d26	},
+	{	XFER_PIO_0,	0x0d029d5e	},
+};
+
+/**
+ *	hpt3x2n_find_mode	-	reset the hpt3x2n bus
+ *	@ap: ATA port
+ *	@speed: transfer mode
+ *
+ *	Return the 32bit register programming information for this channel
+ *	that matches the speed provided. For the moment the clocks table
+ *	is hard coded but easy to change. This will be needed if we use
+ *	different DPLLs
+ */
+
+static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
+{
+	struct hpt_clock *clocks = hpt3x2n_clocks;
+
+	while (clocks->xfer_speed) {
+		if (clocks->xfer_speed == speed)
+			return clocks->timing;
+		clocks++;
+	}
+	BUG();
+	return 0xffffffffU;	/* silence compiler warning */
+}
+
+/**
+ *	hpt372n_filter	-	mode selection filter
+ *	@adev: ATA device
+ *	@mask: mode mask
+ *
+ *	The Marvell bridge chips used on the HighPoint SATA cards do not seem
+ *	to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
+ */
+static unsigned int hpt372n_filter(struct ata_device *adev, unsigned int mask)
+{
+	if (ata_id_is_sata(adev->id))
+		mask &= ~((0xE << ATA_SHIFT_UDMA) | ATA_MASK_MWDMA);
+
+	return mask;
+}
+
+/**
+ *	hpt3x2n_cable_detect	-	Detect the cable type
+ *	@ap: ATA port to detect on
+ *
+ *	Return the cable type attached to this port
+ */
+
+static int hpt3x2n_cable_detect(struct ata_port *ap)
+{
+	u8 scr2, ata66;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+	pci_read_config_byte(pdev, 0x5B, &scr2);
+	pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+
+	udelay(10); /* debounce */
+
+	/* Cable register now active */
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Restore state */
+	pci_write_config_byte(pdev, 0x5B, scr2);
+
+	if (ata66 & (2 >> ap->port_no))
+		return ATA_CBL_PATA40;
+	else
+		return ATA_CBL_PATA80;
+}
+
+/**
+ *	hpt3x2n_pre_reset	-	reset the hpt3x2n bus
+ *	@link: ATA link to reset
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Perform the initial reset handling for the 3x2n series controllers.
+ *	Reset the hardware and state machine,
+ */
+
+static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	static const struct pci_bits hpt3x2n_enable_bits[] = {
+		{ 0x50, 1, 0x04, 0x04 },
+		{ 0x54, 1, 0x04, 0x04 }
+	};
+	u8 mcr2;
+
+	if (!pci_test_config_bits(pdev, &hpt3x2n_enable_bits[ap->port_no]))
+		return -ENOENT;
+
+	/* Reset the state machine */
+	pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+	udelay(100);
+
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, 0x51 + 4 * ap->port_no, &mcr2);
+	mcr2 &= ~0x07;
+	pci_write_config_byte(pdev, 0x51 + 4 * ap->port_no, mcr2);
+
+	return ata_sff_prereset(link, deadline);
+}
+
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+			     u8 mode)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int addr = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	u32 reg, timing, mask;
+
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt3x2n_find_mode(ap, mode);
+
+	pci_read_config_dword(pdev, addr, &reg);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr, reg);
+}
+
+/**
+ *	hpt3x2n_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt3x2n_set_mode(ap, adev, adev->pio_mode);
+}
+
+/**
+ *	hpt3x2n_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes.
+ */
+
+static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt3x2n_set_mode(ap, adev, adev->dma_mode);
+}
+
+/**
+ *	hpt3x2n_bmdma_stop		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Clean up after the HPT3x2n and later DMA engine
+ */
+
+static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int mscreg = 0x50 + 4 * ap->port_no;
+	u8 bwsr_stat, msc_stat;
+
+	pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+	pci_read_config_byte(pdev, mscreg, &msc_stat);
+	if (bwsr_stat & (1 << ap->port_no))
+		pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+	ata_bmdma_stop(qc);
+}
+
+/**
+ *	hpt3x2n_set_clock	-	clock control
+ *	@ap: ATA port
+ *	@source: 0x21 or 0x23 for PLL or PCI sourced clock
+ *
+ *	Switch the ATA bus clock between the PLL and PCI clock sources
+ *	while correctly isolating the bus and resetting internal logic
+ *
+ *	We must use the DPLL for
+ *	-	writing
+ *	-	second channel UDMA7 (SATA ports) or higher
+ *	-	66MHz PCI
+ *
+ *	or we will underclock the device and get reduced performance.
+ */
+
+static void hpt3x2n_set_clock(struct ata_port *ap, int source)
+{
+	void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8;
+
+	/* Tristate the bus */
+	iowrite8(0x80, bmdma+0x73);
+	iowrite8(0x80, bmdma+0x77);
+
+	/* Switch clock and reset channels */
+	iowrite8(source, bmdma+0x7B);
+	iowrite8(0xC0, bmdma+0x79);
+
+	/* Reset state machines, avoid enabling the disabled channels */
+	iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70);
+	iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74);
+
+	/* Complete reset */
+	iowrite8(0x00, bmdma+0x79);
+
+	/* Reconnect channels to bus */
+	iowrite8(0x00, bmdma+0x73);
+	iowrite8(0x00, bmdma+0x77);
+}
+
+static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
+{
+	long flags = (long)ap->host->private_data;
+
+	/* See if we should use the DPLL */
+	if (writing)
+		return USE_DPLL;	/* Needed for write */
+	if (flags & PCI66)
+		return USE_DPLL;	/* Needed at 66Mhz */
+	return 0;
+}
+
+static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct ata_port *alt = ap->host->ports[ap->port_no ^ 1];
+	int rc, flags = (long)ap->host->private_data;
+	int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
+
+	/* First apply the usual rules */
+	rc = ata_std_qc_defer(qc);
+	if (rc != 0)
+		return rc;
+
+	if ((flags & USE_DPLL) != dpll && alt->qc_active)
+		return ATA_DEFER_PORT;
+	return 0;
+}
+
+static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	int flags = (long)ap->host->private_data;
+	int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
+
+	if ((flags & USE_DPLL) != dpll) {
+		flags &= ~USE_DPLL;
+		flags |= dpll;
+		ap->host->private_data = (void *)(long)flags;
+
+		hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23);
+	}
+	return ata_bmdma_qc_issue(qc);
+}
+
+static struct scsi_host_template hpt3x2n_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+/*
+ *	Configuration for HPT302N/371N.
+ */
+
+static struct ata_port_operations hpt3xxn_port_ops = {
+	.inherits	= &ata_bmdma_port_ops,
+
+	.bmdma_stop	= hpt3x2n_bmdma_stop,
+
+	.qc_defer	= hpt3x2n_qc_defer,
+	.qc_issue	= hpt3x2n_qc_issue,
+
+	.cable_detect	= hpt3x2n_cable_detect,
+	.set_piomode	= hpt3x2n_set_piomode,
+	.set_dmamode	= hpt3x2n_set_dmamode,
+	.prereset	= hpt3x2n_pre_reset,
+};
+
+/*
+ *	Configuration for HPT372N. Same as 302N/371N but we have a mode filter.
+ */
+
+static struct ata_port_operations hpt372n_port_ops = {
+	.inherits	= &hpt3xxn_port_ops,
+	.mode_filter	= &hpt372n_filter,
+};
+
+/**
+ *	hpt3xn_calibrate_dpll		-	Calibrate the DPLL loop
+ *	@dev: PCI device
+ *
+ *	Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
+ *	succeeds
+ */
+
+static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
+{
+	u8 reg5b;
+	u32 reg5c;
+	int tries;
+
+	for (tries = 0; tries < 0x5000; tries++) {
+		udelay(50);
+		pci_read_config_byte(dev, 0x5b, &reg5b);
+		if (reg5b & 0x80) {
+			/* See if it stays set */
+			for (tries = 0; tries < 0x1000; tries++) {
+				pci_read_config_byte(dev, 0x5b, &reg5b);
+				/* Failed ? */
+				if ((reg5b & 0x80) == 0)
+					return 0;
+			}
+			/* Turn off tuning, we have the DPLL set */
+			pci_read_config_dword(dev, 0x5c, &reg5c);
+			pci_write_config_dword(dev, 0x5c, reg5c & ~0x100);
+			return 1;
+		}
+	}
+	/* Never went stable */
+	return 0;
+}
+
+static int hpt3x2n_pci_clock(struct pci_dev *pdev, unsigned int base)
+{
+	unsigned int freq;
+	u32 fcnt;
+
+	/*
+	 * Some devices do not let this value be accessed via PCI space
+	 * according to the old driver.
+	 */
+	fcnt = inl(pci_resource_start(pdev, 4) + 0x90);
+	if ((fcnt >> 12) != 0xABCDE) {
+		u32 total = 0;
+		int i;
+		u16 sr;
+
+		dev_warn(&pdev->dev, "BIOS clock data not set\n");
+
+		/* This is the process the HPT371 BIOS is reported to use */
+		for (i = 0; i < 128; i++) {
+			pci_read_config_word(pdev, 0x78, &sr);
+			total += sr & 0x1FF;
+			udelay(15);
+		}
+		fcnt = total / 128;
+	}
+	fcnt &= 0x1FF;
+
+	freq = (fcnt * base) / 192;	/* in MHz */
+
+	/* Clamp to bands */
+	if (freq < 40)
+		return 33;
+	if (freq < 45)
+		return 40;
+	if (freq < 55)
+		return 50;
+	return 66;
+}
+
+/**
+ *	hpt3x2n_init_one		-	Initialise an HPT37X/302
+ *	@dev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Initialise an HPT3x2n device. There are some interesting complications
+ *	here. Firstly the chip may report 366 and be one of several variants.
+ *	Secondly all the timings depend on the clock for the chip which we must
+ *	detect and look up
+ *
+ *	This is the known chip mappings. It may be missing a couple of later
+ *	releases.
+ *
+ *	Chip version		PCI		Rev	Notes
+ *	HPT372			4 (HPT366)	5	Other driver
+ *	HPT372N			4 (HPT366)	6	UDMA133
+ *	HPT372			5 (HPT372)	1	Other driver
+ *	HPT372N			5 (HPT372)	2	UDMA133
+ *	HPT302			6 (HPT302)	*	Other driver
+ *	HPT302N			6 (HPT302)	> 1	UDMA133
+ *	HPT371			7 (HPT371)	*	Other driver
+ *	HPT371N			7 (HPT371)	> 1	UDMA133
+ *	HPT374			8 (HPT374)	*	Other driver
+ *	HPT372N			9 (HPT372N)	*	UDMA133
+ *
+ *	(1) UDMA133 support depends on the bus clock
+ */
+
+static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	/* HPT372N - UDMA133 */
+	static const struct ata_port_info info_hpt372n = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA6,
+		.port_ops = &hpt372n_port_ops
+	};
+	/* HPT302N and HPT371N - UDMA133 */
+	static const struct ata_port_info info_hpt3xxn = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA6,
+		.port_ops = &hpt3xxn_port_ops
+	};
+	const struct ata_port_info *ppi[] = { &info_hpt3xxn, NULL };
+	u8 rev = dev->revision;
+	u8 irqmask;
+	unsigned int pci_mhz;
+	unsigned int f_low, f_high;
+	int adjust;
+	unsigned long iobase = pci_resource_start(dev, 4);
+	void *hpriv = (void *)USE_DPLL;
+	int rc;
+
+	rc = pcim_enable_device(dev);
+	if (rc)
+		return rc;
+
+	switch (dev->device) {
+	case PCI_DEVICE_ID_TTI_HPT366:
+		/* 372N if rev >= 6 */
+		if (rev < 6)
+			return -ENODEV;
+		goto hpt372n;
+	case PCI_DEVICE_ID_TTI_HPT371:
+		/* 371N if rev >= 2 */
+		if (rev < 2)
+			return -ENODEV;
+		break;
+	case PCI_DEVICE_ID_TTI_HPT372:
+		/* 372N if rev >= 2 */
+		if (rev < 2)
+			return -ENODEV;
+		goto hpt372n;
+	case PCI_DEVICE_ID_TTI_HPT302:
+		/* 302N if rev >= 2 */
+		if (rev < 2)
+			return -ENODEV;
+		break;
+	case PCI_DEVICE_ID_TTI_HPT372N:
+hpt372n:
+		ppi[0] = &info_hpt372n;
+		break;
+	default:
+		dev_err(&dev->dev,"PCI table is bogus, please report (%d)\n",
+			dev->device);
+		return -ENODEV;
+	}
+
+	/* Ok so this is a chip we support */
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	pci_read_config_byte(dev, 0x5A, &irqmask);
+	irqmask &= ~0x10;
+	pci_write_config_byte(dev, 0x5a, irqmask);
+
+	/*
+	 * HPT371 chips physically have only one channel, the secondary one,
+	 * but the primary channel registers do exist!  Go figure...
+	 * So,  we manually disable the non-existing channel here
+	 * (if the BIOS hasn't done this already).
+	 */
+	if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
+		u8 mcr1;
+		pci_read_config_byte(dev, 0x50, &mcr1);
+		mcr1 &= ~0x04;
+		pci_write_config_byte(dev, 0x50, mcr1);
+	}
+
+	/*
+	 * Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
+	 * 50 for UDMA100. Right now we always use 66
+	 */
+
+	pci_mhz = hpt3x2n_pci_clock(dev, 77);
+
+	f_low = (pci_mhz * 48) / 66;	/* PCI Mhz for 66Mhz DPLL */
+	f_high = f_low + 2;		/* Tolerance */
+
+	pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
+	/* PLL clock */
+	pci_write_config_byte(dev, 0x5B, 0x21);
+
+	/* Unlike the 37x we don't try jiggling the frequency */
+	for (adjust = 0; adjust < 8; adjust++) {
+		if (hpt3xn_calibrate_dpll(dev))
+			break;
+		pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+	}
+	if (adjust == 8) {
+		dev_err(&dev->dev, "DPLL did not stabilize!\n");
+		return -ENODEV;
+	}
+
+	dev_info(&dev->dev, "bus clock %dMHz, using 66MHz DPLL\n", pci_mhz);
+
+	/*
+	 * Set our private data up. We only need a few flags
+	 * so we use it directly.
+	 */
+	if (pci_mhz > 60)
+		hpriv = (void *)(PCI66 | USE_DPLL);
+
+	/*
+	 * On  HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+	 * the MISC. register to stretch the UltraDMA Tss timing.
+	 * NOTE: This register is only writeable via I/O space.
+	 */
+	if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+		outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
+
+	/* Now kick off ATA set up */
+	return ata_pci_bmdma_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
+}
+
+static const struct pci_device_id hpt3x2n[] = {
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
+
+	{ },
+};
+
+static struct pci_driver hpt3x2n_pci_driver = {
+	.name		= DRV_NAME,
+	.id_table	= hpt3x2n,
+	.probe		= hpt3x2n_init_one,
+	.remove		= ata_pci_remove_one
+};
+
+module_pci_driver(hpt3x2n_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3xxN");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x2n);
+MODULE_VERSION(DRV_VERSION);