Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 173 insertions, 0 deletions

diff --git a/drivers/gpu/drm/tilcdc/tilcdc_drv.h b/drivers/gpu/drm/tilcdc/tilcdc_drv.h
new file mode 100644
index 000000000..b818448c8
--- /dev/null
+++ b/drivers/gpu/drm/tilcdc/tilcdc_drv.h
@@ -0,0 +1,173 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2012 Texas Instruments
+ * Author: Rob Clark <robdclark@gmail.com>
+ */
+
+#ifndef __TILCDC_DRV_H__
+#define __TILCDC_DRV_H__
+
+#include <linux/cpufreq.h>
+#include <linux/irqreturn.h>
+
+#include <drm/drm_print.h>
+
+struct clk;
+struct workqueue_struct;
+
+struct drm_connector;
+struct drm_connector_helper_funcs;
+struct drm_crtc;
+struct drm_device;
+struct drm_display_mode;
+struct drm_encoder;
+struct drm_framebuffer;
+struct drm_minor;
+struct drm_pending_vblank_event;
+struct drm_plane;
+
+/* Defaulting to pixel clock defined on AM335x */
+#define TILCDC_DEFAULT_MAX_PIXELCLOCK  126000
+/* Maximum display width for LCDC V1 */
+#define TILCDC_DEFAULT_MAX_WIDTH_V1  1024
+/* ... and for LCDC V2 found on AM335x: */
+#define TILCDC_DEFAULT_MAX_WIDTH_V2  2048
+/*
+ * This may need some tweaking, but want to allow at least 1280x1024@60
+ * with optimized DDR & EMIF settings tweaked 1920x1080@24 appears to
+ * be supportable
+ */
+#define TILCDC_DEFAULT_MAX_BANDWIDTH  (1280*1024*60)
+
+
+struct tilcdc_drm_private {
+	void __iomem *mmio;
+
+	struct clk *clk;         /* functional clock */
+	int rev;                 /* IP revision */
+
+	unsigned int irq;
+
+	/* don't attempt resolutions w/ higher W * H * Hz: */
+	uint32_t max_bandwidth;
+	/*
+	 * Pixel Clock will be restricted to some value as
+	 * defined in the device datasheet measured in KHz
+	 */
+	uint32_t max_pixelclock;
+	/*
+	 * Max allowable width is limited on a per device basis
+	 * measured in pixels
+	 */
+	uint32_t max_width;
+
+	/* Supported pixel formats */
+	const uint32_t *pixelformats;
+	uint32_t num_pixelformats;
+
+#ifdef CONFIG_CPU_FREQ
+	struct notifier_block freq_transition;
+#endif
+
+	struct workqueue_struct *wq;
+
+	struct drm_crtc *crtc;
+
+	unsigned int num_encoders;
+	struct drm_encoder *encoders[8];
+
+	unsigned int num_connectors;
+	struct drm_connector *connectors[8];
+
+	struct drm_encoder *external_encoder;
+	struct drm_connector *external_connector;
+
+	bool is_registered;
+	bool is_componentized;
+	bool irq_enabled;
+};
+
+/* Sub-module for display.  Since we don't know at compile time what panels
+ * or display adapter(s) might be present (for ex, off chip dvi/tfp410,
+ * hdmi encoder, various lcd panels), the connector/encoder(s) are split into
+ * separate drivers.  If they are probed and found to be present, they
+ * register themselves with tilcdc_register_module().
+ */
+struct tilcdc_module;
+
+struct tilcdc_module_ops {
+	/* create appropriate encoders/connectors: */
+	int (*modeset_init)(struct tilcdc_module *mod, struct drm_device *dev);
+#ifdef CONFIG_DEBUG_FS
+	/* create debugfs nodes (can be NULL): */
+	int (*debugfs_init)(struct tilcdc_module *mod, struct drm_minor *minor);
+#endif
+};
+
+struct tilcdc_module {
+	const char *name;
+	struct list_head list;
+	const struct tilcdc_module_ops *funcs;
+};
+
+void tilcdc_module_init(struct tilcdc_module *mod, const char *name,
+		const struct tilcdc_module_ops *funcs);
+void tilcdc_module_cleanup(struct tilcdc_module *mod);
+
+/* Panel config that needs to be set in the crtc, but is not coming from
+ * the mode timings.  The display module is expected to call
+ * tilcdc_crtc_set_panel_info() to set this during modeset.
+ */
+struct tilcdc_panel_info {
+
+	/* AC Bias Pin Frequency */
+	uint32_t ac_bias;
+
+	/* AC Bias Pin Transitions per Interrupt */
+	uint32_t ac_bias_intrpt;
+
+	/* DMA burst size */
+	uint32_t dma_burst_sz;
+
+	/* Bits per pixel */
+	uint32_t bpp;
+
+	/* FIFO DMA Request Delay */
+	uint32_t fdd;
+
+	/* TFT Alternative Signal Mapping (Only for active) */
+	bool tft_alt_mode;
+
+	/* Invert pixel clock */
+	bool invert_pxl_clk;
+
+	/* Horizontal and Vertical Sync Edge: 0=rising 1=falling */
+	uint32_t sync_edge;
+
+	/* Horizontal and Vertical Sync: Control: 0=ignore */
+	uint32_t sync_ctrl;
+
+	/* Raster Data Order Select: 1=Most-to-least 0=Least-to-most */
+	uint32_t raster_order;
+
+	/* DMA FIFO threshold */
+	uint32_t fifo_th;
+};
+
+#define DBG(fmt, ...) DRM_DEBUG(fmt"\n", ##__VA_ARGS__)
+
+int tilcdc_crtc_create(struct drm_device *dev);
+irqreturn_t tilcdc_crtc_irq(struct drm_crtc *crtc);
+void tilcdc_crtc_update_clk(struct drm_crtc *crtc);
+void tilcdc_crtc_set_panel_info(struct drm_crtc *crtc,
+		const struct tilcdc_panel_info *info);
+void tilcdc_crtc_set_simulate_vesa_sync(struct drm_crtc *crtc,
+					bool simulate_vesa_sync);
+void tilcdc_crtc_shutdown(struct drm_crtc *crtc);
+int tilcdc_crtc_update_fb(struct drm_crtc *crtc,
+		struct drm_framebuffer *fb,
+		struct drm_pending_vblank_event *event);
+
+int tilcdc_plane_init(struct drm_device *dev, struct drm_plane *plane);
+
+#endif /* __TILCDC_DRV_H__ */