Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 99 insertions, 0 deletions

diff --git a/drivers/i2c/busses/i2c-iop3xx.h b/drivers/i2c/busses/i2c-iop3xx.h
new file mode 100644
index 000000000..143548335
--- /dev/null
+++ b/drivers/i2c/busses/i2c-iop3xx.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* ------------------------------------------------------------------------- */
+/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c         */
+/* ------------------------------------------------------------------------- */
+/*   Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
+ *                      <Peter dot Milne at D hyphen TACQ dot com>
+
+ */
+/* ------------------------------------------------------------------------- */
+
+
+#ifndef I2C_IOP3XX_H
+#define I2C_IOP3XX_H 1
+
+/*
+ * iop321 hardware bit definitions
+ */
+#define IOP3XX_ICR_FAST_MODE	0x8000	/* 1=400kBps, 0=100kBps */
+#define IOP3XX_ICR_UNIT_RESET	0x4000	/* 1=RESET */
+#define IOP3XX_ICR_SAD_IE	0x2000	/* 1=Slave Detect Interrupt Enable */
+#define IOP3XX_ICR_ALD_IE	0x1000	/* 1=Arb Loss Detect Interrupt Enable */
+#define IOP3XX_ICR_SSD_IE	0x0800	/* 1=Slave STOP Detect Interrupt Enable */
+#define IOP3XX_ICR_BERR_IE	0x0400	/* 1=Bus Error Interrupt Enable */
+#define IOP3XX_ICR_RXFULL_IE	0x0200	/* 1=Receive Full Interrupt Enable */
+#define IOP3XX_ICR_TXEMPTY_IE	0x0100	/* 1=Transmit Empty Interrupt Enable */
+#define IOP3XX_ICR_GCD		0x0080	/* 1=General Call Disable */
+/*
+ * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
+ * when sending a master mode general call message from the I2C unit"
+ */
+#define IOP3XX_ICR_UE		0x0040	/* 1=Unit Enable */
+/*
+ * "NOTE: To avoid I2C bus integrity problems, 
+ * the user needs to ensure that the GPIO Output Data Register - 
+ * GPOD bits associated with an I2C port are cleared prior to setting 
+ * the enable bit for that I2C serial port. 
+ * The user prepares to enable I2C port 0 and 
+ * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
+ */
+#define IOP3XX_ICR_SCLEN	0x0020	/* 1=SCL enable for master mode */
+#define IOP3XX_ICR_MABORT	0x0010	/* 1=Send a STOP with no data 
+					 * NB TBYTE must be clear */
+#define IOP3XX_ICR_TBYTE	0x0008	/* 1=Send/Receive a byte. i2c clears */
+#define IOP3XX_ICR_NACK		0x0004	/* 1=reply with NACK */
+#define IOP3XX_ICR_MSTOP	0x0002	/* 1=send a STOP after next data byte */
+#define IOP3XX_ICR_MSTART	0x0001	/* 1=initiate a START */
+
+
+#define IOP3XX_ISR_BERRD	0x0400	/* 1=BUS ERROR Detected */
+#define IOP3XX_ISR_SAD		0x0200	/* 1=Slave ADdress Detected */
+#define IOP3XX_ISR_GCAD		0x0100	/* 1=General Call Address Detected */
+#define IOP3XX_ISR_RXFULL	0x0080	/* 1=Receive Full */
+#define IOP3XX_ISR_TXEMPTY	0x0040	/* 1=Transmit Empty */
+#define IOP3XX_ISR_ALD		0x0020	/* 1=Arbitration Loss Detected */
+#define IOP3XX_ISR_SSD		0x0010	/* 1=Slave STOP Detected */
+#define IOP3XX_ISR_BBUSY	0x0008	/* 1=Bus BUSY */
+#define IOP3XX_ISR_UNITBUSY	0x0004	/* 1=Unit Busy */
+#define IOP3XX_ISR_NACK		0x0002	/* 1=Unit Rx or Tx a NACK */
+#define IOP3XX_ISR_RXREAD	0x0001	/* 1=READ 0=WRITE (R/W bit of slave addr */
+
+#define IOP3XX_ISR_CLEARBITS	0x07f0
+
+#define IOP3XX_ISAR_SAMASK	0x007f
+
+#define IOP3XX_IDBR_MASK	0x00ff
+
+#define IOP3XX_IBMR_SCL		0x0002
+#define IOP3XX_IBMR_SDA		0x0001
+
+#define IOP3XX_GPOD_I2C0	0x00c0	/* clear these bits to enable ch0 */
+#define IOP3XX_GPOD_I2C1	0x0030	/* clear these bits to enable ch1 */
+
+#define MYSAR			0	/* default slave address */
+
+#define I2C_ERR			321
+#define I2C_ERR_BERR		(I2C_ERR+0)
+#define I2C_ERR_ALD		(I2C_ERR+1)
+
+
+#define	CR_OFFSET		0
+#define	SR_OFFSET		0x4
+#define	SAR_OFFSET		0x8
+#define	DBR_OFFSET		0xc
+#define	CCR_OFFSET		0x10
+#define	BMR_OFFSET		0x14
+
+#define	IOP3XX_I2C_IO_SIZE	0x18
+
+struct i2c_algo_iop3xx_data {
+	void __iomem *ioaddr;
+	wait_queue_head_t waitq;
+	spinlock_t lock;
+	u32 SR_enabled, SR_received;
+	int id;
+	struct gpio_desc *gpio_scl;
+	struct gpio_desc *gpio_sda;
+};
+
+#endif /* I2C_IOP3XX_H */