Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

35 files changed, 11398 insertions, 0 deletions

diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
new file mode 100644
index 000000000..c9453389e
--- /dev/null
+++ b/drivers/iio/pressure/Kconfig
@@ -0,0 +1,269 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Pressure drivers
+#
+# When adding new entries keep the list in alphabetical order
+
+menu "Pressure sensors"
+
+config ABP060MG
+	tristate "Honeywell ABP pressure sensor driver"
+	depends on I2C
+	help
+	  Say yes here to build support for the Honeywell ABP pressure
+	  sensors.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called abp060mg.
+
+config BMP280
+	tristate "Bosch Sensortec BMP180/BMP280/BMP380 pressure sensor I2C driver"
+	depends on (I2C || SPI_MASTER)
+	select REGMAP
+	select BMP280_I2C if (I2C)
+	select BMP280_SPI if (SPI_MASTER)
+	help
+	  Say yes here to build support for Bosch Sensortec BMP180, BMP280 and
+	  BMP380 pressure and temperature sensors. Also supports the BME280 with
+	  an additional humidity sensor channel.
+
+	  To compile this driver as a module, choose M here: the core module
+	  will be called bmp280 and you will also get bmp280-i2c for I2C
+	  and/or bmp280-spi for SPI support.
+
+config BMP280_I2C
+	tristate
+	depends on BMP280
+	depends on I2C
+	select REGMAP_I2C
+
+config BMP280_SPI
+	tristate
+	depends on BMP280
+	depends on SPI_MASTER
+	select REGMAP
+
+config IIO_CROS_EC_BARO
+	tristate "ChromeOS EC Barometer Sensor"
+	depends on IIO_CROS_EC_SENSORS_CORE
+	help
+	  Say yes here to build support for the Barometer sensor when
+	  presented by the ChromeOS EC Sensor hub.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called cros_ec_baro.
+
+config DLHL60D
+	tristate "All Sensors DLHL60D and DLHL60G low voltage digital pressure sensors"
+	depends on I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	  Say yes here to build support for the All Sensors DLH series
+	  pressure sensors driver.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called dlhl60d.
+
+config DPS310
+	tristate "Infineon DPS310 pressure and temperature sensor"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Support for the Infineon DPS310 digital barometric pressure sensor.
+	  It can be accessed over I2C bus.
+
+	  This driver can also be built as a module.  If so, the module will be
+	  called dps310.
+
+config HID_SENSOR_PRESS
+	depends on HID_SENSOR_HUB
+	select IIO_BUFFER
+	select HID_SENSOR_IIO_COMMON
+	select HID_SENSOR_IIO_TRIGGER
+	tristate "HID PRESS"
+	help
+	  Say yes here to build support for the HID SENSOR
+	  Pressure driver
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called hid-sensor-press.
+
+config HP03
+	tristate "Hope RF HP03 temperature and pressure sensor driver"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say yes here to build support for Hope RF HP03 pressure and
+	  temperature sensor.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called hp03.
+
+config ICP10100
+	tristate "InvenSense ICP-101xx pressure and temperature sensor"
+	depends on I2C
+	select CRC8
+	help
+	  Say yes here to build support for InvenSense ICP-101xx barometric
+	  pressure and temperature sensor.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called icp10100.
+
+config MPL115
+	tristate
+
+config MPL115_I2C
+	tristate "Freescale MPL115A2 pressure sensor driver"
+	depends on I2C
+	select MPL115
+	help
+	  Say yes here to build support for the Freescale MPL115A2
+	  pressure sensor connected via I2C.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mpl115_i2c.
+
+config MPL115_SPI
+	tristate "Freescale MPL115A1 pressure sensor driver"
+	depends on SPI_MASTER
+	select MPL115
+	help
+	  Say yes here to build support for the Freescale MPL115A1
+	  pressure sensor connected via SPI.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mpl115_spi.
+
+config MPL3115
+	tristate "Freescale MPL3115A2 pressure sensor driver"
+	depends on I2C
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	  Say yes here to build support for the Freescale MPL3115A2
+	  pressure sensor / altimeter.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mpl3115.
+
+config MS5611
+	tristate "Measurement Specialties MS5611 pressure sensor driver"
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	help
+	  Say Y here to build support for the Measurement Specialties
+	  MS5611, MS5607 pressure and temperature sensors.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ms5611_core.
+
+config MS5611_I2C
+	tristate "support I2C bus connection"
+	depends on I2C && MS5611
+	help
+	  Say Y here to build I2C bus support for MS5611.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ms5611_i2c.
+
+config MS5611_SPI
+	tristate "support SPI bus connection"
+	depends on SPI_MASTER && MS5611
+	help
+	  Say Y here to build SPI bus support for MS5611.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called ms5611_spi.
+
+config MS5637
+	tristate "Measurement Specialties MS5637 pressure & temperature sensor"
+	depends on I2C
+	select IIO_MS_SENSORS_I2C
+	help
+	  If you say yes here you get support for the Measurement Specialties
+	  MS5637 pressure and temperature sensor.
+	  This driver is also used for MS8607 temperature, pressure & humidity
+	  sensor
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ms5637.
+
+config IIO_ST_PRESS
+	tristate "STMicroelectronics pressure sensor Driver"
+	depends on (I2C || SPI_MASTER) && SYSFS
+	select IIO_ST_SENSORS_CORE
+	select IIO_TRIGGERED_BUFFER if (IIO_BUFFER)
+	help
+	  Say yes here to build support for STMicroelectronics pressure
+	  sensors: LPS001WP, LPS25H, LPS331AP, LPS22HB, LPS22HH.
+
+	  Also need to enable at least one of I2C and SPI interface drivers
+	  below.
+
+config IIO_ST_PRESS_I2C
+	tristate "STMicroelectronics pressure sensor I2C Interface"
+	depends on I2C && IIO_ST_PRESS
+	default I2C && IIO_ST_PRESS
+	select IIO_ST_SENSORS_I2C
+	help
+	  Build support for STMicroelectronics pressure sensor I2C interface.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called st_pressure_i2c.
+
+config IIO_ST_PRESS_SPI
+	tristate "STMicroelectronics pressure sensor SPI Interface"
+	depends on SPI_MASTER && IIO_ST_PRESS
+	default SPI_MASTER && IIO_ST_PRESS
+	select IIO_ST_SENSORS_SPI
+	help
+	  Build support for STMicroelectronics pressure sensor SPI interface.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called st_pressure_spi.
+
+config T5403
+	tristate "EPCOS T5403 digital barometric pressure sensor driver"
+	depends on I2C
+	help
+	  Say yes here to build support for the EPCOS T5403 pressure sensor
+	  connected via I2C.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called t5403.
+
+config HP206C
+	tristate "HOPERF HP206C precision barometer and altimeter sensor"
+	depends on I2C
+	help
+	  Say yes here to build support for the HOPREF HP206C precision
+	  barometer and altimeter sensor.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called hp206c.
+
+config ZPA2326
+	tristate "Murata ZPA2326 pressure sensor driver"
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+	select REGMAP
+	select ZPA2326_I2C if I2C
+	select ZPA2326_SPI if SPI_MASTER
+	help
+	  Say Y here to build support for the Murata ZPA2326 pressure and
+	  temperature sensor.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called zpa2326.
+
+config ZPA2326_I2C
+	tristate
+	select REGMAP_I2C
+
+config ZPA2326_SPI
+	tristate
+	select REGMAP_SPI
+
+endmenu
diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile
new file mode 100644
index 000000000..083ae87ff
--- /dev/null
+++ b/drivers/iio/pressure/Makefile
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for industrial I/O pressure drivers
+#
+
+# When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_ABP060MG) += abp060mg.o
+obj-$(CONFIG_BMP280) += bmp280.o
+bmp280-objs := bmp280-core.o bmp280-regmap.o
+obj-$(CONFIG_BMP280_I2C) += bmp280-i2c.o
+obj-$(CONFIG_BMP280_SPI) += bmp280-spi.o
+obj-$(CONFIG_DLHL60D) += dlhl60d.o
+obj-$(CONFIG_DPS310) += dps310.o
+obj-$(CONFIG_IIO_CROS_EC_BARO) += cros_ec_baro.o
+obj-$(CONFIG_HID_SENSOR_PRESS)   += hid-sensor-press.o
+obj-$(CONFIG_HP03) += hp03.o
+obj-$(CONFIG_ICP10100) += icp10100.o
+obj-$(CONFIG_MPL115) += mpl115.o
+obj-$(CONFIG_MPL115_I2C) += mpl115_i2c.o
+obj-$(CONFIG_MPL115_SPI) += mpl115_spi.o
+obj-$(CONFIG_MPL3115) += mpl3115.o
+obj-$(CONFIG_MS5611) += ms5611_core.o
+obj-$(CONFIG_MS5611_I2C) += ms5611_i2c.o
+obj-$(CONFIG_MS5611_SPI) += ms5611_spi.o
+obj-$(CONFIG_MS5637) += ms5637.o
+obj-$(CONFIG_IIO_ST_PRESS) += st_pressure.o
+st_pressure-y := st_pressure_core.o
+st_pressure-$(CONFIG_IIO_BUFFER) += st_pressure_buffer.o
+obj-$(CONFIG_T5403) += t5403.o
+obj-$(CONFIG_HP206C) += hp206c.o
+obj-$(CONFIG_ZPA2326) += zpa2326.o
+obj-$(CONFIG_ZPA2326_I2C) += zpa2326_i2c.o
+obj-$(CONFIG_ZPA2326_SPI) += zpa2326_spi.o
+
+obj-$(CONFIG_IIO_ST_PRESS_I2C) += st_pressure_i2c.o
+obj-$(CONFIG_IIO_ST_PRESS_SPI) += st_pressure_spi.o
diff --git a/drivers/iio/pressure/abp060mg.c b/drivers/iio/pressure/abp060mg.c
new file mode 100644
index 000000000..e1c3bdb37
--- /dev/null
+++ b/drivers/iio/pressure/abp060mg.c
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 - Marcin Malagowski <mrc@bourne.st>
+ */
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/iio/iio.h>
+
+#define ABP060MG_ERROR_MASK   0xC000
+#define ABP060MG_RESP_TIME_MS 40
+#define ABP060MG_MIN_COUNTS   1638  /* = 0x0666 (10% of u14) */
+#define ABP060MG_MAX_COUNTS   14745 /* = 0x3999 (90% of u14) */
+#define ABP060MG_NUM_COUNTS   (ABP060MG_MAX_COUNTS - ABP060MG_MIN_COUNTS)
+
+enum abp_variant {
+	/* gage [kPa] */
+	ABP006KG, ABP010KG, ABP016KG, ABP025KG, ABP040KG, ABP060KG, ABP100KG,
+	ABP160KG, ABP250KG, ABP400KG, ABP600KG, ABP001GG,
+	/* differential [kPa] */
+	ABP006KD, ABP010KD, ABP016KD, ABP025KD, ABP040KD, ABP060KD, ABP100KD,
+	ABP160KD, ABP250KD, ABP400KD,
+	/* gage [psi] */
+	ABP001PG, ABP005PG, ABP015PG, ABP030PG, ABP060PG, ABP100PG, ABP150PG,
+	/* differential [psi] */
+	ABP001PD, ABP005PD, ABP015PD, ABP030PD, ABP060PD,
+};
+
+struct abp_config {
+	int min;
+	int max;
+};
+
+static struct abp_config abp_config[] = {
+	/* mbar & kPa variants */
+	[ABP006KG] = { .min =       0, .max =     6000 },
+	[ABP010KG] = { .min =       0, .max =    10000 },
+	[ABP016KG] = { .min =       0, .max =    16000 },
+	[ABP025KG] = { .min =       0, .max =    25000 },
+	[ABP040KG] = { .min =       0, .max =    40000 },
+	[ABP060KG] = { .min =       0, .max =    60000 },
+	[ABP100KG] = { .min =       0, .max =   100000 },
+	[ABP160KG] = { .min =       0, .max =   160000 },
+	[ABP250KG] = { .min =       0, .max =   250000 },
+	[ABP400KG] = { .min =       0, .max =   400000 },
+	[ABP600KG] = { .min =       0, .max =   600000 },
+	[ABP001GG] = { .min =       0, .max =  1000000 },
+	[ABP006KD] = { .min =   -6000, .max =     6000 },
+	[ABP010KD] = { .min =  -10000, .max =    10000 },
+	[ABP016KD] = { .min =  -16000, .max =    16000 },
+	[ABP025KD] = { .min =  -25000, .max =    25000 },
+	[ABP040KD] = { .min =  -40000, .max =    40000 },
+	[ABP060KD] = { .min =  -60000, .max =    60000 },
+	[ABP100KD] = { .min = -100000, .max =   100000 },
+	[ABP160KD] = { .min = -160000, .max =   160000 },
+	[ABP250KD] = { .min = -250000, .max =   250000 },
+	[ABP400KD] = { .min = -400000, .max =   400000 },
+	/* psi variants (1 psi ~ 6895 Pa) */
+	[ABP001PG] = { .min =       0, .max =     6985 },
+	[ABP005PG] = { .min =       0, .max =    34474 },
+	[ABP015PG] = { .min =       0, .max =   103421 },
+	[ABP030PG] = { .min =       0, .max =   206843 },
+	[ABP060PG] = { .min =       0, .max =   413686 },
+	[ABP100PG] = { .min =       0, .max =   689476 },
+	[ABP150PG] = { .min =       0, .max =  1034214 },
+	[ABP001PD] = { .min =   -6895, .max =     6895 },
+	[ABP005PD] = { .min =  -34474, .max =    34474 },
+	[ABP015PD] = { .min = -103421, .max =   103421 },
+	[ABP030PD] = { .min = -206843, .max =   206843 },
+	[ABP060PD] = { .min = -413686, .max =   413686 },
+};
+
+struct abp_state {
+	struct i2c_client *client;
+	struct mutex lock;
+
+	/*
+	 * bus-dependent MEASURE_REQUEST length.
+	 * If no SMBUS_QUICK support, need to send dummy byte
+	 */
+	int mreq_len;
+
+	/* model-dependent values (calculated on probe) */
+	int scale;
+	int offset;
+};
+
+static const struct iio_chan_spec abp060mg_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_OFFSET) | BIT(IIO_CHAN_INFO_SCALE),
+	},
+};
+
+static int abp060mg_get_measurement(struct abp_state *state, int *val)
+{
+	struct i2c_client *client = state->client;
+	__be16 buf[2];
+	u16 pressure;
+	int ret;
+
+	buf[0] = 0;
+	ret = i2c_master_send(client, (u8 *)&buf, state->mreq_len);
+	if (ret < 0)
+		return ret;
+
+	msleep_interruptible(ABP060MG_RESP_TIME_MS);
+
+	ret = i2c_master_recv(client, (u8 *)&buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	pressure = be16_to_cpu(buf[0]);
+	if (pressure & ABP060MG_ERROR_MASK)
+		return -EIO;
+
+	if (pressure < ABP060MG_MIN_COUNTS || pressure > ABP060MG_MAX_COUNTS)
+		return -EIO;
+
+	*val = pressure;
+
+	return IIO_VAL_INT;
+}
+
+static int abp060mg_read_raw(struct iio_dev *indio_dev,
+			struct iio_chan_spec const *chan, int *val,
+			int *val2, long mask)
+{
+	struct abp_state *state = iio_priv(indio_dev);
+	int ret;
+
+	mutex_lock(&state->lock);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = abp060mg_get_measurement(state, val);
+		break;
+	case IIO_CHAN_INFO_OFFSET:
+		*val = state->offset;
+		ret = IIO_VAL_INT;
+		break;
+	case IIO_CHAN_INFO_SCALE:
+		*val = state->scale;
+		*val2 = ABP060MG_NUM_COUNTS * 1000; /* to kPa */
+		ret = IIO_VAL_FRACTIONAL;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	mutex_unlock(&state->lock);
+	return ret;
+}
+
+static const struct iio_info abp060mg_info = {
+	.read_raw = abp060mg_read_raw,
+};
+
+static void abp060mg_init_device(struct iio_dev *indio_dev, unsigned long id)
+{
+	struct abp_state *state = iio_priv(indio_dev);
+	struct abp_config *cfg = &abp_config[id];
+
+	state->scale = cfg->max - cfg->min;
+	state->offset = -ABP060MG_MIN_COUNTS;
+
+	if (cfg->min < 0) /* differential */
+		state->offset -= ABP060MG_NUM_COUNTS >> 1;
+}
+
+static int abp060mg_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct iio_dev *indio_dev;
+	struct abp_state *state;
+	unsigned long cfg_id = id->driver_data;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*state));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	state = iio_priv(indio_dev);
+	i2c_set_clientdata(client, state);
+	state->client = client;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_QUICK))
+		state->mreq_len = 1;
+
+	abp060mg_init_device(indio_dev, cfg_id);
+
+	indio_dev->name = dev_name(&client->dev);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &abp060mg_info;
+
+	indio_dev->channels = abp060mg_channels;
+	indio_dev->num_channels = ARRAY_SIZE(abp060mg_channels);
+
+	mutex_init(&state->lock);
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static const struct i2c_device_id abp060mg_id_table[] = {
+	/* mbar & kPa variants (abp060m [60 mbar] == abp006k [6 kPa]) */
+	/*    gage: */
+	{ "abp060mg", ABP006KG }, { "abp006kg", ABP006KG },
+	{ "abp100mg", ABP010KG }, { "abp010kg", ABP010KG },
+	{ "abp160mg", ABP016KG }, { "abp016kg", ABP016KG },
+	{ "abp250mg", ABP025KG }, { "abp025kg", ABP025KG },
+	{ "abp400mg", ABP040KG }, { "abp040kg", ABP040KG },
+	{ "abp600mg", ABP060KG }, { "abp060kg", ABP060KG },
+	{ "abp001bg", ABP100KG }, { "abp100kg", ABP100KG },
+	{ "abp1_6bg", ABP160KG }, { "abp160kg", ABP160KG },
+	{ "abp2_5bg", ABP250KG }, { "abp250kg", ABP250KG },
+	{ "abp004bg", ABP400KG }, { "abp400kg", ABP400KG },
+	{ "abp006bg", ABP600KG }, { "abp600kg", ABP600KG },
+	{ "abp010bg", ABP001GG }, { "abp001gg", ABP001GG },
+	/*    differential: */
+	{ "abp060md", ABP006KD }, { "abp006kd", ABP006KD },
+	{ "abp100md", ABP010KD }, { "abp010kd", ABP010KD },
+	{ "abp160md", ABP016KD }, { "abp016kd", ABP016KD },
+	{ "abp250md", ABP025KD }, { "abp025kd", ABP025KD },
+	{ "abp400md", ABP040KD }, { "abp040kd", ABP040KD },
+	{ "abp600md", ABP060KD }, { "abp060kd", ABP060KD },
+	{ "abp001bd", ABP100KD }, { "abp100kd", ABP100KD },
+	{ "abp1_6bd", ABP160KD }, { "abp160kd", ABP160KD },
+	{ "abp2_5bd", ABP250KD }, { "abp250kd", ABP250KD },
+	{ "abp004bd", ABP400KD }, { "abp400kd", ABP400KD },
+	/* psi variants */
+	/*    gage: */
+	{ "abp001pg", ABP001PG },
+	{ "abp005pg", ABP005PG },
+	{ "abp015pg", ABP015PG },
+	{ "abp030pg", ABP030PG },
+	{ "abp060pg", ABP060PG },
+	{ "abp100pg", ABP100PG },
+	{ "abp150pg", ABP150PG },
+	/*    differential: */
+	{ "abp001pd", ABP001PD },
+	{ "abp005pd", ABP005PD },
+	{ "abp015pd", ABP015PD },
+	{ "abp030pd", ABP030PD },
+	{ "abp060pd", ABP060PD },
+	{ /* empty */ },
+};
+MODULE_DEVICE_TABLE(i2c, abp060mg_id_table);
+
+static struct i2c_driver abp060mg_driver = {
+	.driver = {
+		.name = "abp060mg",
+	},
+	.probe = abp060mg_probe,
+	.id_table = abp060mg_id_table,
+};
+module_i2c_driver(abp060mg_driver);
+
+MODULE_AUTHOR("Marcin Malagowski <mrc@bourne.st>");
+MODULE_DESCRIPTION("Honeywell ABP pressure sensor driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/pressure/bmp280-core.c b/drivers/iio/pressure/bmp280-core.c
new file mode 100644
index 000000000..4c867157a
--- /dev/null
+++ b/drivers/iio/pressure/bmp280-core.c
@@ -0,0 +1,1841 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2010 Christoph Mair <christoph.mair@gmail.com>
+ * Copyright (c) 2012 Bosch Sensortec GmbH
+ * Copyright (c) 2012 Unixphere AB
+ * Copyright (c) 2014 Intel Corporation
+ * Copyright (c) 2016 Linus Walleij <linus.walleij@linaro.org>
+ *
+ * Driver for Bosch Sensortec BMP180 and BMP280 digital pressure sensor.
+ *
+ * Datasheet:
+ * https://cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
+ * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp280-ds001.pdf
+ * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bme280-ds002.pdf
+ * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp388-ds001.pdf
+ *
+ * Notice:
+ * The link to the bmp180 datasheet points to an outdated version missing these changes:
+ * - Changed document referral from ANP015 to BST-MPS-AN004-00 on page 26
+ * - Updated equation for B3 param on section 3.5 to ((((long)AC1 * 4 + X3) << oss) + 2) / 4
+ * - Updated RoHS directive to 2011/65/EU effective 8 June 2011 on page 26
+ */
+
+#define pr_fmt(fmt) "bmp280: " fmt
+
+#include <linux/bitops.h>
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/delay.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h> /* For irq_get_irq_data() */
+#include <linux/completion.h>
+#include <linux/pm_runtime.h>
+#include <linux/random.h>
+
+#include <asm/unaligned.h>
+
+#include "bmp280.h"
+
+/*
+ * These enums are used for indexing into the array of calibration
+ * coefficients for BMP180.
+ */
+enum { AC1, AC2, AC3, AC4, AC5, AC6, B1, B2, MB, MC, MD };
+
+struct bmp180_calib {
+	s16 AC1;
+	s16 AC2;
+	s16 AC3;
+	u16 AC4;
+	u16 AC5;
+	u16 AC6;
+	s16 B1;
+	s16 B2;
+	s16 MB;
+	s16 MC;
+	s16 MD;
+};
+
+/* See datasheet Section 4.2.2. */
+struct bmp280_calib {
+	u16 T1;
+	s16 T2;
+	s16 T3;
+	u16 P1;
+	s16 P2;
+	s16 P3;
+	s16 P4;
+	s16 P5;
+	s16 P6;
+	s16 P7;
+	s16 P8;
+	s16 P9;
+	u8  H1;
+	s16 H2;
+	u8  H3;
+	s16 H4;
+	s16 H5;
+	s8  H6;
+};
+
+/* See datasheet Section 3.11.1. */
+struct bmp380_calib {
+	u16 T1;
+	u16 T2;
+	s8  T3;
+	s16 P1;
+	s16 P2;
+	s8  P3;
+	s8  P4;
+	u16 P5;
+	u16 P6;
+	s8  P7;
+	s8  P8;
+	s16 P9;
+	s8  P10;
+	s8  P11;
+};
+
+static const char *const bmp280_supply_names[] = {
+	"vddd", "vdda"
+};
+
+#define BMP280_NUM_SUPPLIES ARRAY_SIZE(bmp280_supply_names)
+
+enum bmp380_odr {
+	BMP380_ODR_200HZ,
+	BMP380_ODR_100HZ,
+	BMP380_ODR_50HZ,
+	BMP380_ODR_25HZ,
+	BMP380_ODR_12_5HZ,
+	BMP380_ODR_6_25HZ,
+	BMP380_ODR_3_125HZ,
+	BMP380_ODR_1_5625HZ,
+	BMP380_ODR_0_78HZ,
+	BMP380_ODR_0_39HZ,
+	BMP380_ODR_0_2HZ,
+	BMP380_ODR_0_1HZ,
+	BMP380_ODR_0_05HZ,
+	BMP380_ODR_0_02HZ,
+	BMP380_ODR_0_01HZ,
+	BMP380_ODR_0_006HZ,
+	BMP380_ODR_0_003HZ,
+	BMP380_ODR_0_0015HZ,
+};
+
+struct bmp280_data {
+	struct device *dev;
+	struct mutex lock;
+	struct regmap *regmap;
+	struct completion done;
+	bool use_eoc;
+	const struct bmp280_chip_info *chip_info;
+	union {
+		struct bmp180_calib bmp180;
+		struct bmp280_calib bmp280;
+		struct bmp380_calib bmp380;
+	} calib;
+	struct regulator_bulk_data supplies[BMP280_NUM_SUPPLIES];
+	unsigned int start_up_time; /* in microseconds */
+
+	/* log of base 2 of oversampling rate */
+	u8 oversampling_press;
+	u8 oversampling_temp;
+	u8 oversampling_humid;
+	u8 iir_filter_coeff;
+
+	/*
+	 * BMP380 devices introduce sampling frequency configuration. See
+	 * datasheet sections 3.3.3. and 4.3.19 for more details.
+	 *
+	 * BMx280 devices allowed indirect configuration of sampling frequency
+	 * changing the t_standby duration between measurements, as detailed on
+	 * section 3.6.3 of the datasheet.
+	 */
+	int sampling_freq;
+
+	/*
+	 * Carryover value from temperature conversion, used in pressure
+	 * calculation.
+	 */
+	s32 t_fine;
+
+	/*
+	 * DMA (thus cache coherency maintenance) may require the
+	 * transfer buffers to live in their own cache lines.
+	 */
+	union {
+		/* Sensor data buffer */
+		u8 buf[3];
+		/* Calibration data buffers */
+		__le16 bmp280_cal_buf[BMP280_CONTIGUOUS_CALIB_REGS / 2];
+		__be16 bmp180_cal_buf[BMP180_REG_CALIB_COUNT / 2];
+		u8 bmp380_cal_buf[BMP380_CALIB_REG_COUNT];
+		/* Miscellaneous, endianess-aware data buffers */
+		__le16 le16;
+		__be16 be16;
+	} __aligned(IIO_DMA_MINALIGN);
+};
+
+struct bmp280_chip_info {
+	unsigned int id_reg;
+
+	const struct iio_chan_spec *channels;
+	int num_channels;
+	unsigned int start_up_time;
+
+	const int *oversampling_temp_avail;
+	int num_oversampling_temp_avail;
+	int oversampling_temp_default;
+
+	const int *oversampling_press_avail;
+	int num_oversampling_press_avail;
+	int oversampling_press_default;
+
+	const int *oversampling_humid_avail;
+	int num_oversampling_humid_avail;
+	int oversampling_humid_default;
+
+	const int *iir_filter_coeffs_avail;
+	int num_iir_filter_coeffs_avail;
+	int iir_filter_coeff_default;
+
+	const int (*sampling_freq_avail)[2];
+	int num_sampling_freq_avail;
+	int sampling_freq_default;
+
+	int (*chip_config)(struct bmp280_data *);
+	int (*read_temp)(struct bmp280_data *, int *);
+	int (*read_press)(struct bmp280_data *, int *, int *);
+	int (*read_humid)(struct bmp280_data *, int *, int *);
+	int (*read_calib)(struct bmp280_data *);
+};
+
+/*
+ * These enums are used for indexing into the array of compensation
+ * parameters for BMP280.
+ */
+enum { T1, T2, T3, P1, P2, P3, P4, P5, P6, P7, P8, P9 };
+
+enum {
+	/* Temperature calib indexes */
+	BMP380_T1 = 0,
+	BMP380_T2 = 2,
+	BMP380_T3 = 4,
+	/* Pressure calib indexes */
+	BMP380_P1 = 5,
+	BMP380_P2 = 7,
+	BMP380_P3 = 9,
+	BMP380_P4 = 10,
+	BMP380_P5 = 11,
+	BMP380_P6 = 13,
+	BMP380_P7 = 15,
+	BMP380_P8 = 16,
+	BMP380_P9 = 17,
+	BMP380_P10 = 19,
+	BMP380_P11 = 20,
+};
+
+static const struct iio_chan_spec bmp280_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	},
+	{
+		.type = IIO_HUMIDITYRELATIVE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	},
+};
+
+static const struct iio_chan_spec bmp380_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+					   BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+					   BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+	},
+	{
+		.type = IIO_HUMIDITYRELATIVE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+					   BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+	},
+};
+
+static int bmp280_read_calib(struct bmp280_data *data)
+{
+	struct bmp280_calib *calib = &data->calib.bmp280;
+	int ret;
+
+
+	/* Read temperature and pressure calibration values. */
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_TEMP_START,
+			       data->bmp280_cal_buf, sizeof(data->bmp280_cal_buf));
+	if (ret < 0) {
+		dev_err(data->dev,
+			"failed to read temperature and pressure calibration parameters\n");
+		return ret;
+	}
+
+	/* Toss the temperature and pressure calibration data into the entropy pool */
+	add_device_randomness(data->bmp280_cal_buf, sizeof(data->bmp280_cal_buf));
+
+	/* Parse temperature calibration values. */
+	calib->T1 = le16_to_cpu(data->bmp280_cal_buf[T1]);
+	calib->T2 = le16_to_cpu(data->bmp280_cal_buf[T2]);
+	calib->T3 = le16_to_cpu(data->bmp280_cal_buf[T3]);
+
+	/* Parse pressure calibration values. */
+	calib->P1 = le16_to_cpu(data->bmp280_cal_buf[P1]);
+	calib->P2 = le16_to_cpu(data->bmp280_cal_buf[P2]);
+	calib->P3 = le16_to_cpu(data->bmp280_cal_buf[P3]);
+	calib->P4 = le16_to_cpu(data->bmp280_cal_buf[P4]);
+	calib->P5 = le16_to_cpu(data->bmp280_cal_buf[P5]);
+	calib->P6 = le16_to_cpu(data->bmp280_cal_buf[P6]);
+	calib->P7 = le16_to_cpu(data->bmp280_cal_buf[P7]);
+	calib->P8 = le16_to_cpu(data->bmp280_cal_buf[P8]);
+	calib->P9 = le16_to_cpu(data->bmp280_cal_buf[P9]);
+
+	return 0;
+}
+
+static int bme280_read_calib(struct bmp280_data *data)
+{
+	struct bmp280_calib *calib = &data->calib.bmp280;
+	struct device *dev = data->dev;
+	unsigned int tmp;
+	int ret;
+
+	/* Load shared calibration params with bmp280 first */
+	ret = bmp280_read_calib(data);
+	if  (ret < 0) {
+		dev_err(dev, "failed to read common bmp280 calibration parameters\n");
+		return ret;
+	}
+
+	/*
+	 * Read humidity calibration values.
+	 * Due to some odd register addressing we cannot just
+	 * do a big bulk read. Instead, we have to read each Hx
+	 * value separately and sometimes do some bit shifting...
+	 * Humidity data is only available on BME280.
+	 */
+
+	ret = regmap_read(data->regmap, BMP280_REG_COMP_H1, &tmp);
+	if (ret < 0) {
+		dev_err(dev, "failed to read H1 comp value\n");
+		return ret;
+	}
+	calib->H1 = tmp;
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H2,
+			       &data->le16, sizeof(data->le16));
+	if (ret < 0) {
+		dev_err(dev, "failed to read H2 comp value\n");
+		return ret;
+	}
+	calib->H2 = sign_extend32(le16_to_cpu(data->le16), 15);
+
+	ret = regmap_read(data->regmap, BMP280_REG_COMP_H3, &tmp);
+	if (ret < 0) {
+		dev_err(dev, "failed to read H3 comp value\n");
+		return ret;
+	}
+	calib->H3 = tmp;
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H4,
+			       &data->be16, sizeof(data->be16));
+	if (ret < 0) {
+		dev_err(dev, "failed to read H4 comp value\n");
+		return ret;
+	}
+	calib->H4 = sign_extend32(((be16_to_cpu(data->be16) >> 4) & 0xff0) |
+				  (be16_to_cpu(data->be16) & 0xf), 11);
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H5,
+			       &data->le16, sizeof(data->le16));
+	if (ret < 0) {
+		dev_err(dev, "failed to read H5 comp value\n");
+		return ret;
+	}
+	calib->H5 = sign_extend32(FIELD_GET(BMP280_COMP_H5_MASK, le16_to_cpu(data->le16)), 11);
+
+	ret = regmap_read(data->regmap, BMP280_REG_COMP_H6, &tmp);
+	if (ret < 0) {
+		dev_err(dev, "failed to read H6 comp value\n");
+		return ret;
+	}
+	calib->H6 = sign_extend32(tmp, 7);
+
+	return 0;
+}
+/*
+ * Returns humidity in percent, resolution is 0.01 percent. Output value of
+ * "47445" represents 47445/1024 = 46.333 %RH.
+ *
+ * Taken from BME280 datasheet, Section 4.2.3, "Compensation formula".
+ */
+static u32 bmp280_compensate_humidity(struct bmp280_data *data,
+				      s32 adc_humidity)
+{
+	struct bmp280_calib *calib = &data->calib.bmp280;
+	s32 var;
+
+	var = ((s32)data->t_fine) - (s32)76800;
+	var = ((((adc_humidity << 14) - (calib->H4 << 20) - (calib->H5 * var))
+		+ (s32)16384) >> 15) * (((((((var * calib->H6) >> 10)
+		* (((var * (s32)calib->H3) >> 11) + (s32)32768)) >> 10)
+		+ (s32)2097152) * calib->H2 + 8192) >> 14);
+	var -= ((((var >> 15) * (var >> 15)) >> 7) * (s32)calib->H1) >> 4;
+
+	var = clamp_val(var, 0, 419430400);
+
+	return var >> 12;
+};
+
+/*
+ * Returns temperature in DegC, resolution is 0.01 DegC.  Output value of
+ * "5123" equals 51.23 DegC.  t_fine carries fine temperature as global
+ * value.
+ *
+ * Taken from datasheet, Section 3.11.3, "Compensation formula".
+ */
+static s32 bmp280_compensate_temp(struct bmp280_data *data,
+				  s32 adc_temp)
+{
+	struct bmp280_calib *calib = &data->calib.bmp280;
+	s32 var1, var2;
+
+	var1 = (((adc_temp >> 3) - ((s32)calib->T1 << 1)) *
+		((s32)calib->T2)) >> 11;
+	var2 = (((((adc_temp >> 4) - ((s32)calib->T1)) *
+		  ((adc_temp >> 4) - ((s32)calib->T1))) >> 12) *
+		((s32)calib->T3)) >> 14;
+	data->t_fine = var1 + var2;
+
+	return (data->t_fine * 5 + 128) >> 8;
+}
+
+/*
+ * Returns pressure in Pa as unsigned 32 bit integer in Q24.8 format (24
+ * integer bits and 8 fractional bits).  Output value of "24674867"
+ * represents 24674867/256 = 96386.2 Pa = 963.862 hPa
+ *
+ * Taken from datasheet, Section 3.11.3, "Compensation formula".
+ */
+static u32 bmp280_compensate_press(struct bmp280_data *data,
+				   s32 adc_press)
+{
+	struct bmp280_calib *calib = &data->calib.bmp280;
+	s64 var1, var2, p;
+
+	var1 = ((s64)data->t_fine) - 128000;
+	var2 = var1 * var1 * (s64)calib->P6;
+	var2 += (var1 * (s64)calib->P5) << 17;
+	var2 += ((s64)calib->P4) << 35;
+	var1 = ((var1 * var1 * (s64)calib->P3) >> 8) +
+		((var1 * (s64)calib->P2) << 12);
+	var1 = ((((s64)1) << 47) + var1) * ((s64)calib->P1) >> 33;
+
+	if (var1 == 0)
+		return 0;
+
+	p = ((((s64)1048576 - adc_press) << 31) - var2) * 3125;
+	p = div64_s64(p, var1);
+	var1 = (((s64)calib->P9) * (p >> 13) * (p >> 13)) >> 25;
+	var2 = ((s64)(calib->P8) * p) >> 19;
+	p = ((p + var1 + var2) >> 8) + (((s64)calib->P7) << 4);
+
+	return (u32)p;
+}
+
+static int bmp280_read_temp(struct bmp280_data *data,
+			    int *val)
+{
+	s32 adc_temp, comp_temp;
+	int ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_TEMP_MSB,
+			       data->buf, sizeof(data->buf));
+	if (ret < 0) {
+		dev_err(data->dev, "failed to read temperature\n");
+		return ret;
+	}
+
+	adc_temp = FIELD_GET(BMP280_MEAS_TRIM_MASK, get_unaligned_be24(data->buf));
+	if (adc_temp == BMP280_TEMP_SKIPPED) {
+		/* reading was skipped */
+		dev_err(data->dev, "reading temperature skipped\n");
+		return -EIO;
+	}
+	comp_temp = bmp280_compensate_temp(data, adc_temp);
+
+	/*
+	 * val might be NULL if we're called by the read_press routine,
+	 * who only cares about the carry over t_fine value.
+	 */
+	if (val) {
+		*val = comp_temp * 10;
+		return IIO_VAL_INT;
+	}
+
+	return 0;
+}
+
+static int bmp280_read_press(struct bmp280_data *data,
+			     int *val, int *val2)
+{
+	u32 comp_press;
+	s32 adc_press;
+	int ret;
+
+	/* Read and compensate temperature so we get a reading of t_fine. */
+	ret = bmp280_read_temp(data, NULL);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_PRESS_MSB,
+			       data->buf, sizeof(data->buf));
+	if (ret < 0) {
+		dev_err(data->dev, "failed to read pressure\n");
+		return ret;
+	}
+
+	adc_press = FIELD_GET(BMP280_MEAS_TRIM_MASK, get_unaligned_be24(data->buf));
+	if (adc_press == BMP280_PRESS_SKIPPED) {
+		/* reading was skipped */
+		dev_err(data->dev, "reading pressure skipped\n");
+		return -EIO;
+	}
+	comp_press = bmp280_compensate_press(data, adc_press);
+
+	*val = comp_press;
+	*val2 = 256000;
+
+	return IIO_VAL_FRACTIONAL;
+}
+
+static int bmp280_read_humid(struct bmp280_data *data, int *val, int *val2)
+{
+	u32 comp_humidity;
+	s32 adc_humidity;
+	int ret;
+
+	/* Read and compensate temperature so we get a reading of t_fine. */
+	ret = bmp280_read_temp(data, NULL);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP280_REG_HUMIDITY_MSB,
+			       &data->be16, sizeof(data->be16));
+	if (ret < 0) {
+		dev_err(data->dev, "failed to read humidity\n");
+		return ret;
+	}
+
+	adc_humidity = be16_to_cpu(data->be16);
+	if (adc_humidity == BMP280_HUMIDITY_SKIPPED) {
+		/* reading was skipped */
+		dev_err(data->dev, "reading humidity skipped\n");
+		return -EIO;
+	}
+	comp_humidity = bmp280_compensate_humidity(data, adc_humidity);
+
+	*val = comp_humidity * 1000 / 1024;
+
+	return IIO_VAL_INT;
+}
+
+static int bmp280_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	struct bmp280_data *data = iio_priv(indio_dev);
+	int ret;
+
+	pm_runtime_get_sync(data->dev);
+	mutex_lock(&data->lock);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		switch (chan->type) {
+		case IIO_HUMIDITYRELATIVE:
+			ret = data->chip_info->read_humid(data, val, val2);
+			break;
+		case IIO_PRESSURE:
+			ret = data->chip_info->read_press(data, val, val2);
+			break;
+		case IIO_TEMP:
+			ret = data->chip_info->read_temp(data, val);
+			break;
+		default:
+			ret = -EINVAL;
+			break;
+		}
+		break;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		switch (chan->type) {
+		case IIO_HUMIDITYRELATIVE:
+			*val = 1 << data->oversampling_humid;
+			ret = IIO_VAL_INT;
+			break;
+		case IIO_PRESSURE:
+			*val = 1 << data->oversampling_press;
+			ret = IIO_VAL_INT;
+			break;
+		case IIO_TEMP:
+			*val = 1 << data->oversampling_temp;
+			ret = IIO_VAL_INT;
+			break;
+		default:
+			ret = -EINVAL;
+			break;
+		}
+		break;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		if (!data->chip_info->sampling_freq_avail) {
+			ret = -EINVAL;
+			break;
+		}
+
+		*val = data->chip_info->sampling_freq_avail[data->sampling_freq][0];
+		*val2 = data->chip_info->sampling_freq_avail[data->sampling_freq][1];
+		ret = IIO_VAL_INT_PLUS_MICRO;
+		break;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+		if (!data->chip_info->iir_filter_coeffs_avail) {
+			ret = -EINVAL;
+			break;
+		}
+
+		*val = (1 << data->iir_filter_coeff) - 1;
+		ret = IIO_VAL_INT;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	mutex_unlock(&data->lock);
+	pm_runtime_mark_last_busy(data->dev);
+	pm_runtime_put_autosuspend(data->dev);
+
+	return ret;
+}
+
+static int bmp280_write_oversampling_ratio_humid(struct bmp280_data *data,
+					       int val)
+{
+	const int *avail = data->chip_info->oversampling_humid_avail;
+	const int n = data->chip_info->num_oversampling_humid_avail;
+	int ret, prev;
+	int i;
+
+	for (i = 0; i < n; i++) {
+		if (avail[i] == val) {
+			prev = data->oversampling_humid;
+			data->oversampling_humid = ilog2(val);
+
+			ret = data->chip_info->chip_config(data);
+			if (ret) {
+				data->oversampling_humid = prev;
+				data->chip_info->chip_config(data);
+				return ret;
+			}
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int bmp280_write_oversampling_ratio_temp(struct bmp280_data *data,
+					       int val)
+{
+	const int *avail = data->chip_info->oversampling_temp_avail;
+	const int n = data->chip_info->num_oversampling_temp_avail;
+	int ret, prev;
+	int i;
+
+	for (i = 0; i < n; i++) {
+		if (avail[i] == val) {
+			prev = data->oversampling_temp;
+			data->oversampling_temp = ilog2(val);
+
+			ret = data->chip_info->chip_config(data);
+			if (ret) {
+				data->oversampling_temp = prev;
+				data->chip_info->chip_config(data);
+				return ret;
+			}
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int bmp280_write_oversampling_ratio_press(struct bmp280_data *data,
+					       int val)
+{
+	const int *avail = data->chip_info->oversampling_press_avail;
+	const int n = data->chip_info->num_oversampling_press_avail;
+	int ret, prev;
+	int i;
+
+	for (i = 0; i < n; i++) {
+		if (avail[i] == val) {
+			prev = data->oversampling_press;
+			data->oversampling_press = ilog2(val);
+
+			ret = data->chip_info->chip_config(data);
+			if (ret) {
+				data->oversampling_press = prev;
+				data->chip_info->chip_config(data);
+				return ret;
+			}
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int bmp280_write_sampling_frequency(struct bmp280_data *data,
+					   int val, int val2)
+{
+	const int (*avail)[2] = data->chip_info->sampling_freq_avail;
+	const int n = data->chip_info->num_sampling_freq_avail;
+	int ret, prev;
+	int i;
+
+	for (i = 0; i < n; i++) {
+		if (avail[i][0] == val && avail[i][1] == val2) {
+			prev = data->sampling_freq;
+			data->sampling_freq = i;
+
+			ret = data->chip_info->chip_config(data);
+			if (ret) {
+				data->sampling_freq = prev;
+				data->chip_info->chip_config(data);
+				return ret;
+			}
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int bmp280_write_iir_filter_coeffs(struct bmp280_data *data, int val)
+{
+	const int *avail = data->chip_info->iir_filter_coeffs_avail;
+	const int n = data->chip_info->num_iir_filter_coeffs_avail;
+	int ret, prev;
+	int i;
+
+	for (i = 0; i < n; i++) {
+		if (avail[i] - 1  == val) {
+			prev = data->iir_filter_coeff;
+			data->iir_filter_coeff = i;
+
+			ret = data->chip_info->chip_config(data);
+			if (ret) {
+				data->iir_filter_coeff = prev;
+				data->chip_info->chip_config(data);
+				return ret;
+
+			}
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static int bmp280_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct bmp280_data *data = iio_priv(indio_dev);
+	int ret = 0;
+
+	/*
+	 * Helper functions to update sensor running configuration.
+	 * If an error happens applying new settings, will try restore
+	 * previous parameters to ensure the sensor is left in a known
+	 * working configuration.
+	 */
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		pm_runtime_get_sync(data->dev);
+		mutex_lock(&data->lock);
+		switch (chan->type) {
+		case IIO_HUMIDITYRELATIVE:
+			ret = bmp280_write_oversampling_ratio_humid(data, val);
+			break;
+		case IIO_PRESSURE:
+			ret = bmp280_write_oversampling_ratio_press(data, val);
+			break;
+		case IIO_TEMP:
+			ret = bmp280_write_oversampling_ratio_temp(data, val);
+			break;
+		default:
+			ret = -EINVAL;
+			break;
+		}
+		mutex_unlock(&data->lock);
+		pm_runtime_mark_last_busy(data->dev);
+		pm_runtime_put_autosuspend(data->dev);
+		break;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		pm_runtime_get_sync(data->dev);
+		mutex_lock(&data->lock);
+		ret = bmp280_write_sampling_frequency(data, val, val2);
+		mutex_unlock(&data->lock);
+		pm_runtime_mark_last_busy(data->dev);
+		pm_runtime_put_autosuspend(data->dev);
+		break;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+		pm_runtime_get_sync(data->dev);
+		mutex_lock(&data->lock);
+		ret = bmp280_write_iir_filter_coeffs(data, val);
+		mutex_unlock(&data->lock);
+		pm_runtime_mark_last_busy(data->dev);
+		pm_runtime_put_autosuspend(data->dev);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int bmp280_read_avail(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     const int **vals, int *type, int *length,
+			     long mask)
+{
+	struct bmp280_data *data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			*vals = data->chip_info->oversampling_press_avail;
+			*length = data->chip_info->num_oversampling_press_avail;
+			break;
+		case IIO_TEMP:
+			*vals = data->chip_info->oversampling_temp_avail;
+			*length = data->chip_info->num_oversampling_temp_avail;
+			break;
+		default:
+			return -EINVAL;
+		}
+		*type = IIO_VAL_INT;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*vals = (const int *)data->chip_info->sampling_freq_avail;
+		*type = IIO_VAL_INT_PLUS_MICRO;
+		/* Values are stored in a 2D matrix */
+		*length = data->chip_info->num_sampling_freq_avail;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+		*vals = data->chip_info->iir_filter_coeffs_avail;
+		*type = IIO_VAL_INT;
+		*length = data->chip_info->num_iir_filter_coeffs_avail;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info bmp280_info = {
+	.read_raw = &bmp280_read_raw,
+	.read_avail = &bmp280_read_avail,
+	.write_raw = &bmp280_write_raw,
+};
+
+static int bmp280_chip_config(struct bmp280_data *data)
+{
+	u8 osrs = FIELD_PREP(BMP280_OSRS_TEMP_MASK, data->oversampling_temp + 1) |
+		  FIELD_PREP(BMP280_OSRS_PRESS_MASK, data->oversampling_press + 1);
+	int ret;
+
+	ret = regmap_write_bits(data->regmap, BMP280_REG_CTRL_MEAS,
+				 BMP280_OSRS_TEMP_MASK |
+				 BMP280_OSRS_PRESS_MASK |
+				 BMP280_MODE_MASK,
+				 osrs | BMP280_MODE_NORMAL);
+	if (ret < 0) {
+		dev_err(data->dev,
+			"failed to write ctrl_meas register\n");
+		return ret;
+	}
+
+	ret = regmap_update_bits(data->regmap, BMP280_REG_CONFIG,
+				 BMP280_FILTER_MASK,
+				 BMP280_FILTER_4X);
+	if (ret < 0) {
+		dev_err(data->dev,
+			"failed to write config register\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static const int bmp280_oversampling_avail[] = { 1, 2, 4, 8, 16 };
+
+static const struct bmp280_chip_info bmp280_chip_info = {
+	.id_reg = BMP280_REG_ID,
+	.start_up_time = 2000,
+	.channels = bmp280_channels,
+	.num_channels = 2,
+
+	.oversampling_temp_avail = bmp280_oversampling_avail,
+	.num_oversampling_temp_avail = ARRAY_SIZE(bmp280_oversampling_avail),
+	/*
+	 * Oversampling config values on BMx280 have one additional setting
+	 * that other generations of the family don't:
+	 * The value 0 means the measurement is bypassed instead of
+	 * oversampling set to x1.
+	 *
+	 * To account for this difference, and preserve the same common
+	 * config logic, this is handled later on chip_config callback
+	 * incrementing one unit the oversampling setting.
+	 */
+	.oversampling_temp_default = BMP280_OSRS_TEMP_2X - 1,
+
+	.oversampling_press_avail = bmp280_oversampling_avail,
+	.num_oversampling_press_avail = ARRAY_SIZE(bmp280_oversampling_avail),
+	.oversampling_press_default = BMP280_OSRS_PRESS_16X - 1,
+
+	.chip_config = bmp280_chip_config,
+	.read_temp = bmp280_read_temp,
+	.read_press = bmp280_read_press,
+	.read_calib = bmp280_read_calib,
+};
+
+static int bme280_chip_config(struct bmp280_data *data)
+{
+	u8 osrs = FIELD_PREP(BMP280_OSRS_HUMIDITY_MASK, data->oversampling_humid + 1);
+	int ret;
+
+	/*
+	 * Oversampling of humidity must be set before oversampling of
+	 * temperature/pressure is set to become effective.
+	 */
+	ret = regmap_update_bits(data->regmap, BMP280_REG_CTRL_HUMIDITY,
+				  BMP280_OSRS_HUMIDITY_MASK, osrs);
+
+	if (ret < 0)
+		return ret;
+
+	return bmp280_chip_config(data);
+}
+
+static const struct bmp280_chip_info bme280_chip_info = {
+	.id_reg = BMP280_REG_ID,
+	.start_up_time = 2000,
+	.channels = bmp280_channels,
+	.num_channels = 3,
+
+	.oversampling_temp_avail = bmp280_oversampling_avail,
+	.num_oversampling_temp_avail = ARRAY_SIZE(bmp280_oversampling_avail),
+	.oversampling_temp_default = BMP280_OSRS_TEMP_2X - 1,
+
+	.oversampling_press_avail = bmp280_oversampling_avail,
+	.num_oversampling_press_avail = ARRAY_SIZE(bmp280_oversampling_avail),
+	.oversampling_press_default = BMP280_OSRS_PRESS_16X - 1,
+
+	.oversampling_humid_avail = bmp280_oversampling_avail,
+	.num_oversampling_humid_avail = ARRAY_SIZE(bmp280_oversampling_avail),
+	.oversampling_humid_default = BMP280_OSRS_HUMIDITY_16X - 1,
+
+	.chip_config = bme280_chip_config,
+	.read_temp = bmp280_read_temp,
+	.read_press = bmp280_read_press,
+	.read_humid = bmp280_read_humid,
+	.read_calib = bme280_read_calib,
+};
+
+/*
+ * Helper function to send a command to BMP3XX sensors.
+ *
+ * Sensor processes commands written to the CMD register and signals
+ * execution result through "cmd_rdy" and "cmd_error" flags available on
+ * STATUS and ERROR registers.
+ */
+static int bmp380_cmd(struct bmp280_data *data, u8 cmd)
+{
+	unsigned int reg;
+	int ret;
+
+	/* Check if device is ready to process a command */
+	ret = regmap_read(data->regmap, BMP380_REG_STATUS, &reg);
+	if (ret) {
+		dev_err(data->dev, "failed to read error register\n");
+		return ret;
+	}
+	if (!(reg & BMP380_STATUS_CMD_RDY_MASK)) {
+		dev_err(data->dev, "device is not ready to accept commands\n");
+		return -EBUSY;
+	}
+
+	/* Send command to process */
+	ret = regmap_write(data->regmap, BMP380_REG_CMD, cmd);
+	if (ret) {
+		dev_err(data->dev, "failed to send command to device\n");
+		return ret;
+	}
+	/* Wait for 2ms for command to be processed */
+	usleep_range(data->start_up_time, data->start_up_time + 100);
+	/* Check for command processing error */
+	ret = regmap_read(data->regmap, BMP380_REG_ERROR, &reg);
+	if (ret) {
+		dev_err(data->dev, "error reading ERROR reg\n");
+		return ret;
+	}
+	if (reg & BMP380_ERR_CMD_MASK) {
+		dev_err(data->dev, "error processing command 0x%X\n", cmd);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/*
+ * Returns temperature in Celsius dregrees, resolution is 0.01º C. Output value of
+ * "5123" equals 51.2º C. t_fine carries fine temperature as global value.
+ *
+ * Taken from datasheet, Section Appendix 9, "Compensation formula" and repo
+ * https://github.com/BoschSensortec/BMP3-Sensor-API.
+ */
+static s32 bmp380_compensate_temp(struct bmp280_data *data, u32 adc_temp)
+{
+	s64 var1, var2, var3, var4, var5, var6, comp_temp;
+	struct bmp380_calib *calib = &data->calib.bmp380;
+
+	var1 = ((s64) adc_temp) - (((s64) calib->T1) << 8);
+	var2 = var1 * ((s64) calib->T2);
+	var3 = var1 * var1;
+	var4 = var3 * ((s64) calib->T3);
+	var5 = (var2 << 18) + var4;
+	var6 = var5 >> 32;
+	data->t_fine = (s32) var6;
+	comp_temp = (var6 * 25) >> 14;
+
+	comp_temp = clamp_val(comp_temp, BMP380_MIN_TEMP, BMP380_MAX_TEMP);
+	return (s32) comp_temp;
+}
+
+/*
+ * Returns pressure in Pa as an unsigned 32 bit integer in fractional Pascal.
+ * Output value of "9528709" represents 9528709/100 = 95287.09 Pa = 952.8709 hPa.
+ *
+ * Taken from datasheet, Section 9.3. "Pressure compensation" and repository
+ * https://github.com/BoschSensortec/BMP3-Sensor-API.
+ */
+static u32 bmp380_compensate_press(struct bmp280_data *data, u32 adc_press)
+{
+	s64 var1, var2, var3, var4, var5, var6, offset, sensitivity;
+	struct bmp380_calib *calib = &data->calib.bmp380;
+	u32 comp_press;
+
+	var1 = (s64)data->t_fine * (s64)data->t_fine;
+	var2 = var1 >> 6;
+	var3 = (var2 * ((s64) data->t_fine)) >> 8;
+	var4 = ((s64)calib->P8 * var3) >> 5;
+	var5 = ((s64)calib->P7 * var1) << 4;
+	var6 = ((s64)calib->P6 * (s64)data->t_fine) << 22;
+	offset = ((s64)calib->P5 << 47) + var4 + var5 + var6;
+	var2 = ((s64)calib->P4 * var3) >> 5;
+	var4 = ((s64)calib->P3 * var1) << 2;
+	var5 = ((s64)calib->P2 - ((s64)1 << 14)) *
+	       ((s64)data->t_fine << 21);
+	sensitivity = (((s64) calib->P1 - ((s64) 1 << 14)) << 46) +
+			var2 + var4 + var5;
+	var1 = (sensitivity >> 24) * (s64)adc_press;
+	var2 = (s64)calib->P10 * (s64)data->t_fine;
+	var3 = var2 + ((s64)calib->P9 << 16);
+	var4 = (var3 * (s64)adc_press) >> 13;
+
+	/*
+	 * Dividing by 10 followed by multiplying by 10 to avoid
+	 * possible overflow caused by (uncomp_data->pressure * partial_data4).
+	 */
+	var5 = ((s64)adc_press * div_s64(var4, 10)) >> 9;
+	var5 *= 10;
+	var6 = (s64)adc_press * (s64)adc_press;
+	var2 = ((s64)calib->P11 * var6) >> 16;
+	var3 = (var2 * (s64)adc_press) >> 7;
+	var4 = (offset >> 2) + var1 + var5 + var3;
+	comp_press = ((u64)var4 * 25) >> 40;
+
+	comp_press = clamp_val(comp_press, BMP380_MIN_PRES, BMP380_MAX_PRES);
+	return comp_press;
+}
+
+static int bmp380_read_temp(struct bmp280_data *data, int *val)
+{
+	s32 comp_temp;
+	u32 adc_temp;
+	int ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_TEMP_XLSB,
+			       data->buf, sizeof(data->buf));
+	if (ret) {
+		dev_err(data->dev, "failed to read temperature\n");
+		return ret;
+	}
+
+	adc_temp = get_unaligned_le24(data->buf);
+	if (adc_temp == BMP380_TEMP_SKIPPED) {
+		dev_err(data->dev, "reading temperature skipped\n");
+		return -EIO;
+	}
+	comp_temp = bmp380_compensate_temp(data, adc_temp);
+
+	/*
+	 * Val might be NULL if we're called by the read_press routine,
+	 * who only cares about the carry over t_fine value.
+	 */
+	if (val) {
+		/* IIO reports temperatures in milli Celsius */
+		*val = comp_temp * 10;
+		return IIO_VAL_INT;
+	}
+
+	return 0;
+}
+
+static int bmp380_read_press(struct bmp280_data *data, int *val, int *val2)
+{
+	s32 comp_press;
+	u32 adc_press;
+	int ret;
+
+	/* Read and compensate for temperature so we get a reading of t_fine */
+	ret = bmp380_read_temp(data, NULL);
+	if (ret)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_PRESS_XLSB,
+			       data->buf, sizeof(data->buf));
+	if (ret) {
+		dev_err(data->dev, "failed to read pressure\n");
+		return ret;
+	}
+
+	adc_press = get_unaligned_le24(data->buf);
+	if (adc_press == BMP380_PRESS_SKIPPED) {
+		dev_err(data->dev, "reading pressure skipped\n");
+		return -EIO;
+	}
+	comp_press = bmp380_compensate_press(data, adc_press);
+
+	*val = comp_press;
+	/* Compensated pressure is in cPa (centipascals) */
+	*val2 = 100000;
+
+	return IIO_VAL_FRACTIONAL;
+}
+
+static int bmp380_read_calib(struct bmp280_data *data)
+{
+	struct bmp380_calib *calib = &data->calib.bmp380;
+	int ret;
+
+	/* Read temperature and pressure calibration data */
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_CALIB_TEMP_START,
+			       data->bmp380_cal_buf, sizeof(data->bmp380_cal_buf));
+	if (ret) {
+		dev_err(data->dev,
+			"failed to read temperature calibration parameters\n");
+		return ret;
+	}
+
+	/* Toss the temperature calibration data into the entropy pool */
+	add_device_randomness(data->bmp380_cal_buf, sizeof(data->bmp380_cal_buf));
+
+	/* Parse calibration values */
+	calib->T1 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_T1]);
+	calib->T2 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_T2]);
+	calib->T3 = data->bmp380_cal_buf[BMP380_T3];
+	calib->P1 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P1]);
+	calib->P2 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P2]);
+	calib->P3 = data->bmp380_cal_buf[BMP380_P3];
+	calib->P4 = data->bmp380_cal_buf[BMP380_P4];
+	calib->P5 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P5]);
+	calib->P6 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P6]);
+	calib->P7 = data->bmp380_cal_buf[BMP380_P7];
+	calib->P8 = data->bmp380_cal_buf[BMP380_P8];
+	calib->P9 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P9]);
+	calib->P10 = data->bmp380_cal_buf[BMP380_P10];
+	calib->P11 = data->bmp380_cal_buf[BMP380_P11];
+
+	return 0;
+}
+
+static const int bmp380_odr_table[][2] = {
+	[BMP380_ODR_200HZ]	= {200, 0},
+	[BMP380_ODR_100HZ]	= {100, 0},
+	[BMP380_ODR_50HZ]	= {50, 0},
+	[BMP380_ODR_25HZ]	= {25, 0},
+	[BMP380_ODR_12_5HZ]	= {12, 500000},
+	[BMP380_ODR_6_25HZ]	= {6, 250000},
+	[BMP380_ODR_3_125HZ]	= {3, 125000},
+	[BMP380_ODR_1_5625HZ]	= {1, 562500},
+	[BMP380_ODR_0_78HZ]	= {0, 781250},
+	[BMP380_ODR_0_39HZ]	= {0, 390625},
+	[BMP380_ODR_0_2HZ]	= {0, 195313},
+	[BMP380_ODR_0_1HZ]	= {0, 97656},
+	[BMP380_ODR_0_05HZ]	= {0, 48828},
+	[BMP380_ODR_0_02HZ]	= {0, 24414},
+	[BMP380_ODR_0_01HZ]	= {0, 12207},
+	[BMP380_ODR_0_006HZ]	= {0, 6104},
+	[BMP380_ODR_0_003HZ]	= {0, 3052},
+	[BMP380_ODR_0_0015HZ]	= {0, 1526},
+};
+
+static int bmp380_chip_config(struct bmp280_data *data)
+{
+	bool change = false, aux;
+	unsigned int tmp;
+	u8 osrs;
+	int ret;
+
+	/* Configure power control register */
+	ret = regmap_update_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+				 BMP380_CTRL_SENSORS_MASK,
+				 BMP380_CTRL_SENSORS_PRESS_EN |
+				 BMP380_CTRL_SENSORS_TEMP_EN);
+	if (ret) {
+		dev_err(data->dev,
+			"failed to write operation control register\n");
+		return ret;
+	}
+
+	/* Configure oversampling */
+	osrs = FIELD_PREP(BMP380_OSRS_TEMP_MASK, data->oversampling_temp) |
+	       FIELD_PREP(BMP380_OSRS_PRESS_MASK, data->oversampling_press);
+
+	ret = regmap_update_bits_check(data->regmap, BMP380_REG_OSR,
+				       BMP380_OSRS_TEMP_MASK |
+				       BMP380_OSRS_PRESS_MASK,
+				       osrs, &aux);
+	if (ret) {
+		dev_err(data->dev, "failed to write oversampling register\n");
+		return ret;
+	}
+	change = change || aux;
+
+	/* Configure output data rate */
+	ret = regmap_update_bits_check(data->regmap, BMP380_REG_ODR,
+				       BMP380_ODRS_MASK, data->sampling_freq, &aux);
+	if (ret) {
+		dev_err(data->dev, "failed to write ODR selection register\n");
+		return ret;
+	}
+	change = change || aux;
+
+	/* Set filter data */
+	ret = regmap_update_bits_check(data->regmap, BMP380_REG_CONFIG, BMP380_FILTER_MASK,
+				       FIELD_PREP(BMP380_FILTER_MASK, data->iir_filter_coeff),
+				       &aux);
+	if (ret) {
+		dev_err(data->dev, "failed to write config register\n");
+		return ret;
+	}
+	change = change || aux;
+
+	if (change) {
+		/*
+		 * The configurations errors are detected on the fly during a measurement
+		 * cycle. If the sampling frequency is too low, it's faster to reset
+		 * the measurement loop than wait until the next measurement is due.
+		 *
+		 * Resets sensor measurement loop toggling between sleep and normal
+		 * operating modes.
+		 */
+		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+					BMP380_MODE_MASK,
+					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_SLEEP));
+		if (ret) {
+			dev_err(data->dev, "failed to set sleep mode\n");
+			return ret;
+		}
+		usleep_range(2000, 2500);
+		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+					BMP380_MODE_MASK,
+					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_NORMAL));
+		if (ret) {
+			dev_err(data->dev, "failed to set normal mode\n");
+			return ret;
+		}
+		/*
+		 * Waits for measurement before checking configuration error flag.
+		 * Selected longest measure time indicated in section 3.9.1
+		 * in the datasheet.
+		 */
+		msleep(80);
+
+		/* Check config error flag */
+		ret = regmap_read(data->regmap, BMP380_REG_ERROR, &tmp);
+		if (ret) {
+			dev_err(data->dev,
+				"failed to read error register\n");
+			return ret;
+		}
+		if (tmp & BMP380_ERR_CONF_MASK) {
+			dev_warn(data->dev,
+				"sensor flagged configuration as incompatible\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static const int bmp380_oversampling_avail[] = { 1, 2, 4, 8, 16, 32 };
+static const int bmp380_iir_filter_coeffs_avail[] = { 1, 2, 4, 8, 16, 32, 64, 128};
+
+static const struct bmp280_chip_info bmp380_chip_info = {
+	.id_reg = BMP380_REG_ID,
+	.start_up_time = 2000,
+	.channels = bmp380_channels,
+	.num_channels = 2,
+
+	.oversampling_temp_avail = bmp380_oversampling_avail,
+	.num_oversampling_temp_avail = ARRAY_SIZE(bmp380_oversampling_avail),
+	.oversampling_temp_default = ilog2(1),
+
+	.oversampling_press_avail = bmp380_oversampling_avail,
+	.num_oversampling_press_avail = ARRAY_SIZE(bmp380_oversampling_avail),
+	.oversampling_press_default = ilog2(4),
+
+	.sampling_freq_avail = bmp380_odr_table,
+	.num_sampling_freq_avail = ARRAY_SIZE(bmp380_odr_table) * 2,
+	.sampling_freq_default = BMP380_ODR_50HZ,
+
+	.iir_filter_coeffs_avail = bmp380_iir_filter_coeffs_avail,
+	.num_iir_filter_coeffs_avail = ARRAY_SIZE(bmp380_iir_filter_coeffs_avail),
+	.iir_filter_coeff_default = 2,
+
+	.chip_config = bmp380_chip_config,
+	.read_temp = bmp380_read_temp,
+	.read_press = bmp380_read_press,
+	.read_calib = bmp380_read_calib,
+};
+
+static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)
+{
+	const int conversion_time_max[] = { 4500, 7500, 13500, 25500 };
+	unsigned int delay_us;
+	unsigned int ctrl;
+	int ret;
+
+	if (data->use_eoc)
+		reinit_completion(&data->done);
+
+	ret = regmap_write(data->regmap, BMP280_REG_CTRL_MEAS, ctrl_meas);
+	if (ret)
+		return ret;
+
+	if (data->use_eoc) {
+		/*
+		 * If we have a completion interrupt, use it, wait up to
+		 * 100ms. The longest conversion time listed is 76.5 ms for
+		 * advanced resolution mode.
+		 */
+		ret = wait_for_completion_timeout(&data->done,
+						  1 + msecs_to_jiffies(100));
+		if (!ret)
+			dev_err(data->dev, "timeout waiting for completion\n");
+	} else {
+		if (FIELD_GET(BMP180_MEAS_CTRL_MASK, ctrl_meas) == BMP180_MEAS_TEMP)
+			delay_us = 4500;
+		else
+			delay_us =
+				conversion_time_max[data->oversampling_press];
+
+		usleep_range(delay_us, delay_us + 1000);
+	}
+
+	ret = regmap_read(data->regmap, BMP280_REG_CTRL_MEAS, &ctrl);
+	if (ret)
+		return ret;
+
+	/* The value of this bit reset to "0" after conversion is complete */
+	if (ctrl & BMP180_MEAS_SCO)
+		return -EIO;
+
+	return 0;
+}
+
+static int bmp180_read_adc_temp(struct bmp280_data *data, int *val)
+{
+	int ret;
+
+	ret = bmp180_measure(data,
+			     FIELD_PREP(BMP180_MEAS_CTRL_MASK, BMP180_MEAS_TEMP) |
+			     BMP180_MEAS_SCO);
+	if (ret)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP180_REG_OUT_MSB,
+			       &data->be16, sizeof(data->be16));
+	if (ret)
+		return ret;
+
+	*val = be16_to_cpu(data->be16);
+
+	return 0;
+}
+
+static int bmp180_read_calib(struct bmp280_data *data)
+{
+	struct bmp180_calib *calib = &data->calib.bmp180;
+	int ret;
+	int i;
+
+	ret = regmap_bulk_read(data->regmap, BMP180_REG_CALIB_START,
+			       data->bmp180_cal_buf, sizeof(data->bmp180_cal_buf));
+
+	if (ret < 0)
+		return ret;
+
+	/* None of the words has the value 0 or 0xFFFF */
+	for (i = 0; i < ARRAY_SIZE(data->bmp180_cal_buf); i++) {
+		if (data->bmp180_cal_buf[i] == cpu_to_be16(0) ||
+		    data->bmp180_cal_buf[i] == cpu_to_be16(0xffff))
+			return -EIO;
+	}
+
+	/* Toss the calibration data into the entropy pool */
+	add_device_randomness(data->bmp180_cal_buf, sizeof(data->bmp180_cal_buf));
+
+	calib->AC1 = be16_to_cpu(data->bmp180_cal_buf[AC1]);
+	calib->AC2 = be16_to_cpu(data->bmp180_cal_buf[AC2]);
+	calib->AC3 = be16_to_cpu(data->bmp180_cal_buf[AC3]);
+	calib->AC4 = be16_to_cpu(data->bmp180_cal_buf[AC4]);
+	calib->AC5 = be16_to_cpu(data->bmp180_cal_buf[AC5]);
+	calib->AC6 = be16_to_cpu(data->bmp180_cal_buf[AC6]);
+	calib->B1 = be16_to_cpu(data->bmp180_cal_buf[B1]);
+	calib->B2 = be16_to_cpu(data->bmp180_cal_buf[B2]);
+	calib->MB = be16_to_cpu(data->bmp180_cal_buf[MB]);
+	calib->MC = be16_to_cpu(data->bmp180_cal_buf[MC]);
+	calib->MD = be16_to_cpu(data->bmp180_cal_buf[MD]);
+
+	return 0;
+}
+
+/*
+ * Returns temperature in DegC, resolution is 0.1 DegC.
+ * t_fine carries fine temperature as global value.
+ *
+ * Taken from datasheet, Section 3.5, "Calculating pressure and temperature".
+ */
+static s32 bmp180_compensate_temp(struct bmp280_data *data, s32 adc_temp)
+{
+	struct bmp180_calib *calib = &data->calib.bmp180;
+	s32 x1, x2;
+
+	x1 = ((adc_temp - calib->AC6) * calib->AC5) >> 15;
+	x2 = (calib->MC << 11) / (x1 + calib->MD);
+	data->t_fine = x1 + x2;
+
+	return (data->t_fine + 8) >> 4;
+}
+
+static int bmp180_read_temp(struct bmp280_data *data, int *val)
+{
+	s32 adc_temp, comp_temp;
+	int ret;
+
+	ret = bmp180_read_adc_temp(data, &adc_temp);
+	if (ret)
+		return ret;
+
+	comp_temp = bmp180_compensate_temp(data, adc_temp);
+
+	/*
+	 * val might be NULL if we're called by the read_press routine,
+	 * who only cares about the carry over t_fine value.
+	 */
+	if (val) {
+		*val = comp_temp * 100;
+		return IIO_VAL_INT;
+	}
+
+	return 0;
+}
+
+static int bmp180_read_adc_press(struct bmp280_data *data, int *val)
+{
+	u8 oss = data->oversampling_press;
+	int ret;
+
+	ret = bmp180_measure(data,
+			     FIELD_PREP(BMP180_MEAS_CTRL_MASK, BMP180_MEAS_PRESS) |
+			     FIELD_PREP(BMP180_OSRS_PRESS_MASK, oss) |
+			     BMP180_MEAS_SCO);
+	if (ret)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP180_REG_OUT_MSB,
+			       data->buf, sizeof(data->buf));
+	if (ret)
+		return ret;
+
+	*val = get_unaligned_be24(data->buf) >> (8 - oss);
+
+	return 0;
+}
+
+/*
+ * Returns pressure in Pa, resolution is 1 Pa.
+ *
+ * Taken from datasheet, Section 3.5, "Calculating pressure and temperature".
+ */
+static u32 bmp180_compensate_press(struct bmp280_data *data, s32 adc_press)
+{
+	struct bmp180_calib *calib = &data->calib.bmp180;
+	s32 oss = data->oversampling_press;
+	s32 x1, x2, x3, p;
+	s32 b3, b6;
+	u32 b4, b7;
+
+	b6 = data->t_fine - 4000;
+	x1 = (calib->B2 * (b6 * b6 >> 12)) >> 11;
+	x2 = calib->AC2 * b6 >> 11;
+	x3 = x1 + x2;
+	b3 = ((((s32)calib->AC1 * 4 + x3) << oss) + 2) / 4;
+	x1 = calib->AC3 * b6 >> 13;
+	x2 = (calib->B1 * ((b6 * b6) >> 12)) >> 16;
+	x3 = (x1 + x2 + 2) >> 2;
+	b4 = calib->AC4 * (u32)(x3 + 32768) >> 15;
+	b7 = ((u32)adc_press - b3) * (50000 >> oss);
+	if (b7 < 0x80000000)
+		p = (b7 * 2) / b4;
+	else
+		p = (b7 / b4) * 2;
+
+	x1 = (p >> 8) * (p >> 8);
+	x1 = (x1 * 3038) >> 16;
+	x2 = (-7357 * p) >> 16;
+
+	return p + ((x1 + x2 + 3791) >> 4);
+}
+
+static int bmp180_read_press(struct bmp280_data *data,
+			     int *val, int *val2)
+{
+	u32 comp_press;
+	s32 adc_press;
+	int ret;
+
+	/* Read and compensate temperature so we get a reading of t_fine. */
+	ret = bmp180_read_temp(data, NULL);
+	if (ret)
+		return ret;
+
+	ret = bmp180_read_adc_press(data, &adc_press);
+	if (ret)
+		return ret;
+
+	comp_press = bmp180_compensate_press(data, adc_press);
+
+	*val = comp_press;
+	*val2 = 1000;
+
+	return IIO_VAL_FRACTIONAL;
+}
+
+static int bmp180_chip_config(struct bmp280_data *data)
+{
+	return 0;
+}
+
+static const int bmp180_oversampling_temp_avail[] = { 1 };
+static const int bmp180_oversampling_press_avail[] = { 1, 2, 4, 8 };
+
+static const struct bmp280_chip_info bmp180_chip_info = {
+	.id_reg = BMP280_REG_ID,
+	.start_up_time = 2000,
+	.channels = bmp280_channels,
+	.num_channels = 2,
+
+	.oversampling_temp_avail = bmp180_oversampling_temp_avail,
+	.num_oversampling_temp_avail =
+		ARRAY_SIZE(bmp180_oversampling_temp_avail),
+	.oversampling_temp_default = 0,
+
+	.oversampling_press_avail = bmp180_oversampling_press_avail,
+	.num_oversampling_press_avail =
+		ARRAY_SIZE(bmp180_oversampling_press_avail),
+	.oversampling_press_default = BMP180_MEAS_PRESS_8X,
+
+	.chip_config = bmp180_chip_config,
+	.read_temp = bmp180_read_temp,
+	.read_press = bmp180_read_press,
+	.read_calib = bmp180_read_calib,
+};
+
+static irqreturn_t bmp085_eoc_irq(int irq, void *d)
+{
+	struct bmp280_data *data = d;
+
+	complete(&data->done);
+
+	return IRQ_HANDLED;
+}
+
+static int bmp085_fetch_eoc_irq(struct device *dev,
+				const char *name,
+				int irq,
+				struct bmp280_data *data)
+{
+	unsigned long irq_trig;
+	int ret;
+
+	irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+	if (irq_trig != IRQF_TRIGGER_RISING) {
+		dev_err(dev, "non-rising trigger given for EOC interrupt, trying to enforce it\n");
+		irq_trig = IRQF_TRIGGER_RISING;
+	}
+
+	init_completion(&data->done);
+
+	ret = devm_request_threaded_irq(dev,
+			irq,
+			bmp085_eoc_irq,
+			NULL,
+			irq_trig,
+			name,
+			data);
+	if (ret) {
+		/* Bail out without IRQ but keep the driver in place */
+		dev_err(dev, "unable to request DRDY IRQ\n");
+		return 0;
+	}
+
+	data->use_eoc = true;
+	return 0;
+}
+
+static void bmp280_pm_disable(void *data)
+{
+	struct device *dev = data;
+
+	pm_runtime_get_sync(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+	struct regulator_bulk_data *supplies = data;
+
+	regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
+int bmp280_common_probe(struct device *dev,
+			struct regmap *regmap,
+			unsigned int chip,
+			const char *name,
+			int irq)
+{
+	const struct bmp280_chip_info *chip_info;
+	struct iio_dev *indio_dev;
+	struct bmp280_data *data;
+	struct gpio_desc *gpiod;
+	unsigned int chip_id;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	mutex_init(&data->lock);
+	data->dev = dev;
+
+	indio_dev->name = name;
+	indio_dev->info = &bmp280_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	switch (chip) {
+	case BMP180_CHIP_ID:
+		chip_info = &bmp180_chip_info;
+		break;
+	case BMP280_CHIP_ID:
+		chip_info = &bmp280_chip_info;
+		break;
+	case BME280_CHIP_ID:
+		chip_info = &bme280_chip_info;
+		break;
+	case BMP380_CHIP_ID:
+		chip_info = &bmp380_chip_info;
+		break;
+	default:
+		return -EINVAL;
+	}
+	data->chip_info = chip_info;
+
+	/* Apply initial values from chip info structure */
+	indio_dev->channels = chip_info->channels;
+	indio_dev->num_channels = chip_info->num_channels;
+	data->oversampling_press = chip_info->oversampling_press_default;
+	data->oversampling_humid = chip_info->oversampling_humid_default;
+	data->oversampling_temp = chip_info->oversampling_temp_default;
+	data->iir_filter_coeff = chip_info->iir_filter_coeff_default;
+	data->sampling_freq = chip_info->sampling_freq_default;
+	data->start_up_time = chip_info->start_up_time;
+
+	/* Bring up regulators */
+	regulator_bulk_set_supply_names(data->supplies,
+					bmp280_supply_names,
+					BMP280_NUM_SUPPLIES);
+
+	ret = devm_regulator_bulk_get(dev,
+				      BMP280_NUM_SUPPLIES, data->supplies);
+	if (ret) {
+		dev_err(dev, "failed to get regulators\n");
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(BMP280_NUM_SUPPLIES, data->supplies);
+	if (ret) {
+		dev_err(dev, "failed to enable regulators\n");
+		return ret;
+	}
+
+	ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+				       data->supplies);
+	if (ret)
+		return ret;
+
+	/* Wait to make sure we started up properly */
+	usleep_range(data->start_up_time, data->start_up_time + 100);
+
+	/* Bring chip out of reset if there is an assigned GPIO line */
+	gpiod = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	/* Deassert the signal */
+	if (gpiod) {
+		dev_info(dev, "release reset\n");
+		gpiod_set_value(gpiod, 0);
+	}
+
+	data->regmap = regmap;
+
+	ret = regmap_read(regmap, data->chip_info->id_reg, &chip_id);
+	if (ret < 0)
+		return ret;
+	if (chip_id != chip) {
+		dev_err(dev, "bad chip id: expected %x got %x\n",
+			chip, chip_id);
+		return -EINVAL;
+	}
+
+	/* BMP3xx requires soft-reset as part of initialization */
+	if (chip_id == BMP380_CHIP_ID) {
+		ret = bmp380_cmd(data, BMP380_CMD_SOFT_RESET);
+		if (ret < 0)
+			return ret;
+	}
+
+	ret = data->chip_info->chip_config(data);
+	if (ret < 0)
+		return ret;
+
+	dev_set_drvdata(dev, indio_dev);
+
+	/*
+	 * Some chips have calibration parameters "programmed into the devices'
+	 * non-volatile memory during production". Let's read them out at probe
+	 * time once. They will not change.
+	 */
+
+	ret = data->chip_info->read_calib(data);
+	if (ret < 0)
+		return dev_err_probe(data->dev, ret,
+				     "failed to read calibration coefficients\n");
+
+	/*
+	 * Attempt to grab an optional EOC IRQ - only the BMP085 has this
+	 * however as it happens, the BMP085 shares the chip ID of BMP180
+	 * so we look for an IRQ if we have that.
+	 */
+	if (irq > 0 && (chip_id  == BMP180_CHIP_ID)) {
+		ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
+		if (ret)
+			return ret;
+	}
+
+	/* Enable runtime PM */
+	pm_runtime_get_noresume(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Set autosuspend to two orders of magnitude larger than the
+	 * start-up time.
+	 */
+	pm_runtime_set_autosuspend_delay(dev, data->start_up_time / 10);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_put(dev);
+
+	ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
+	if (ret)
+		return ret;
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+EXPORT_SYMBOL_NS(bmp280_common_probe, IIO_BMP280);
+
+static int bmp280_runtime_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct bmp280_data *data = iio_priv(indio_dev);
+
+	return regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
+}
+
+static int bmp280_runtime_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct bmp280_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = regulator_bulk_enable(BMP280_NUM_SUPPLIES, data->supplies);
+	if (ret)
+		return ret;
+	usleep_range(data->start_up_time, data->start_up_time + 100);
+	return data->chip_info->chip_config(data);
+}
+
+EXPORT_RUNTIME_DEV_PM_OPS(bmp280_dev_pm_ops, bmp280_runtime_suspend,
+			  bmp280_runtime_resume, NULL);
+
+MODULE_AUTHOR("Vlad Dogaru <vlad.dogaru@intel.com>");
+MODULE_DESCRIPTION("Driver for Bosch Sensortec BMP180/BMP280 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/bmp280-i2c.c b/drivers/iio/pressure/bmp280-i2c.c
new file mode 100644
index 000000000..0c27211f3
--- /dev/null
+++ b/drivers/iio/pressure/bmp280-i2c.c
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+
+#include "bmp280.h"
+
+static int bmp280_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct regmap *regmap;
+	const struct regmap_config *regmap_config;
+
+	switch (id->driver_data) {
+	case BMP180_CHIP_ID:
+		regmap_config = &bmp180_regmap_config;
+		break;
+	case BMP280_CHIP_ID:
+	case BME280_CHIP_ID:
+		regmap_config = &bmp280_regmap_config;
+		break;
+	case BMP380_CHIP_ID:
+		regmap_config = &bmp380_regmap_config;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap = devm_regmap_init_i2c(client, regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&client->dev, "failed to allocate register map\n");
+		return PTR_ERR(regmap);
+	}
+
+	return bmp280_common_probe(&client->dev,
+				   regmap,
+				   id->driver_data,
+				   id->name,
+				   client->irq);
+}
+
+static const struct of_device_id bmp280_of_i2c_match[] = {
+	{ .compatible = "bosch,bmp085", .data = (void *)BMP180_CHIP_ID },
+	{ .compatible = "bosch,bmp180", .data = (void *)BMP180_CHIP_ID },
+	{ .compatible = "bosch,bmp280", .data = (void *)BMP280_CHIP_ID },
+	{ .compatible = "bosch,bme280", .data = (void *)BME280_CHIP_ID },
+	{ .compatible = "bosch,bmp380", .data = (void *)BMP380_CHIP_ID },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match);
+
+static const struct i2c_device_id bmp280_i2c_id[] = {
+	{"bmp085", BMP180_CHIP_ID },
+	{"bmp180", BMP180_CHIP_ID },
+	{"bmp280", BMP280_CHIP_ID },
+	{"bme280", BME280_CHIP_ID },
+	{"bmp380", BMP380_CHIP_ID },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, bmp280_i2c_id);
+
+static struct i2c_driver bmp280_i2c_driver = {
+	.driver = {
+		.name	= "bmp280",
+		.of_match_table = bmp280_of_i2c_match,
+		.pm = pm_ptr(&bmp280_dev_pm_ops),
+	},
+	.probe		= bmp280_i2c_probe,
+	.id_table	= bmp280_i2c_id,
+};
+module_i2c_driver(bmp280_i2c_driver);
+
+MODULE_AUTHOR("Vlad Dogaru <vlad.dogaru@intel.com>");
+MODULE_DESCRIPTION("Driver for Bosch Sensortec BMP180/BMP280 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_BMP280);
diff --git a/drivers/iio/pressure/bmp280-regmap.c b/drivers/iio/pressure/bmp280-regmap.c
new file mode 100644
index 000000000..c98c67970
--- /dev/null
+++ b/drivers/iio/pressure/bmp280-regmap.c
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "bmp280.h"
+
+static bool bmp180_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP280_REG_CTRL_MEAS:
+	case BMP280_REG_RESET:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool bmp180_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP180_REG_OUT_XLSB:
+	case BMP180_REG_OUT_LSB:
+	case BMP180_REG_OUT_MSB:
+	case BMP280_REG_CTRL_MEAS:
+		return true;
+	default:
+		return false;
+	}
+}
+
+const struct regmap_config bmp180_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = BMP180_REG_OUT_XLSB,
+	.cache_type = REGCACHE_RBTREE,
+
+	.writeable_reg = bmp180_is_writeable_reg,
+	.volatile_reg = bmp180_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS(bmp180_regmap_config, IIO_BMP280);
+
+static bool bmp280_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP280_REG_CONFIG:
+	case BMP280_REG_CTRL_HUMIDITY:
+	case BMP280_REG_CTRL_MEAS:
+	case BMP280_REG_RESET:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool bmp280_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP280_REG_HUMIDITY_LSB:
+	case BMP280_REG_HUMIDITY_MSB:
+	case BMP280_REG_TEMP_XLSB:
+	case BMP280_REG_TEMP_LSB:
+	case BMP280_REG_TEMP_MSB:
+	case BMP280_REG_PRESS_XLSB:
+	case BMP280_REG_PRESS_LSB:
+	case BMP280_REG_PRESS_MSB:
+	case BMP280_REG_STATUS:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool bmp380_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP380_REG_CMD:
+	case BMP380_REG_CONFIG:
+	case BMP380_REG_FIFO_CONFIG_1:
+	case BMP380_REG_FIFO_CONFIG_2:
+	case BMP380_REG_FIFO_WATERMARK_LSB:
+	case BMP380_REG_FIFO_WATERMARK_MSB:
+	case BMP380_REG_POWER_CONTROL:
+	case BMP380_REG_INT_CONTROL:
+	case BMP380_REG_IF_CONFIG:
+	case BMP380_REG_ODR:
+	case BMP380_REG_OSR:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool bmp380_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP380_REG_TEMP_XLSB:
+	case BMP380_REG_TEMP_LSB:
+	case BMP380_REG_TEMP_MSB:
+	case BMP380_REG_PRESS_XLSB:
+	case BMP380_REG_PRESS_LSB:
+	case BMP380_REG_PRESS_MSB:
+	case BMP380_REG_SENSOR_TIME_XLSB:
+	case BMP380_REG_SENSOR_TIME_LSB:
+	case BMP380_REG_SENSOR_TIME_MSB:
+	case BMP380_REG_INT_STATUS:
+	case BMP380_REG_FIFO_DATA:
+	case BMP380_REG_STATUS:
+	case BMP380_REG_ERROR:
+	case BMP380_REG_EVENT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+const struct regmap_config bmp280_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = BMP280_REG_HUMIDITY_LSB,
+	.cache_type = REGCACHE_RBTREE,
+
+	.writeable_reg = bmp280_is_writeable_reg,
+	.volatile_reg = bmp280_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS(bmp280_regmap_config, IIO_BMP280);
+
+const struct regmap_config bmp380_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = BMP380_REG_CMD,
+	.cache_type = REGCACHE_RBTREE,
+
+	.writeable_reg = bmp380_is_writeable_reg,
+	.volatile_reg = bmp380_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS(bmp380_regmap_config, IIO_BMP280);
diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
new file mode 100644
index 000000000..011c68e07
--- /dev/null
+++ b/drivers/iio/pressure/bmp280-spi.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * SPI interface for the BMP280 driver
+ *
+ * Inspired by the older BMP085 driver drivers/misc/bmp085-spi.c
+ */
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/err.h>
+#include <linux/regmap.h>
+
+#include "bmp280.h"
+
+static int bmp280_regmap_spi_write(void *context, const void *data,
+                                   size_t count)
+{
+	struct device *dev = context;
+	struct spi_device *spi = to_spi_device(dev);
+	u8 buf[2];
+
+	memcpy(buf, data, 2);
+	/*
+	 * The SPI register address (= full register address without bit 7) and
+	 * the write command (bit7 = RW = '0')
+	 */
+	buf[0] &= ~0x80;
+
+	return spi_write_then_read(spi, buf, 2, NULL, 0);
+}
+
+static int bmp280_regmap_spi_read(void *context, const void *reg,
+                                  size_t reg_size, void *val, size_t val_size)
+{
+	struct device *dev = context;
+	struct spi_device *spi = to_spi_device(dev);
+
+	return spi_write_then_read(spi, reg, reg_size, val, val_size);
+}
+
+static struct regmap_bus bmp280_regmap_bus = {
+	.write = bmp280_regmap_spi_write,
+	.read = bmp280_regmap_spi_read,
+	.reg_format_endian_default = REGMAP_ENDIAN_BIG,
+	.val_format_endian_default = REGMAP_ENDIAN_BIG,
+};
+
+static int bmp280_spi_probe(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+	struct regmap *regmap;
+	const struct regmap_config *regmap_config;
+	int ret;
+
+	spi->bits_per_word = 8;
+	ret = spi_setup(spi);
+	if (ret < 0) {
+		dev_err(&spi->dev, "spi_setup failed!\n");
+		return ret;
+	}
+
+	switch (id->driver_data) {
+	case BMP180_CHIP_ID:
+		regmap_config = &bmp180_regmap_config;
+		break;
+	case BMP280_CHIP_ID:
+	case BME280_CHIP_ID:
+		regmap_config = &bmp280_regmap_config;
+		break;
+	case BMP380_CHIP_ID:
+		regmap_config = &bmp380_regmap_config;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap = devm_regmap_init(&spi->dev,
+				  &bmp280_regmap_bus,
+				  &spi->dev,
+				  regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&spi->dev, "failed to allocate register map\n");
+		return PTR_ERR(regmap);
+	}
+
+	return bmp280_common_probe(&spi->dev,
+				   regmap,
+				   id->driver_data,
+				   id->name,
+				   spi->irq);
+}
+
+static const struct of_device_id bmp280_of_spi_match[] = {
+	{ .compatible = "bosch,bmp085", },
+	{ .compatible = "bosch,bmp180", },
+	{ .compatible = "bosch,bmp181", },
+	{ .compatible = "bosch,bmp280", },
+	{ .compatible = "bosch,bme280", },
+	{ .compatible = "bosch,bmp380", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bmp280_of_spi_match);
+
+static const struct spi_device_id bmp280_spi_id[] = {
+	{ "bmp180", BMP180_CHIP_ID },
+	{ "bmp181", BMP180_CHIP_ID },
+	{ "bmp280", BMP280_CHIP_ID },
+	{ "bme280", BME280_CHIP_ID },
+	{ "bmp380", BMP380_CHIP_ID },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, bmp280_spi_id);
+
+static struct spi_driver bmp280_spi_driver = {
+	.driver = {
+		.name = "bmp280",
+		.of_match_table = bmp280_of_spi_match,
+		.pm = pm_ptr(&bmp280_dev_pm_ops),
+	},
+	.id_table = bmp280_spi_id,
+	.probe = bmp280_spi_probe,
+};
+module_spi_driver(bmp280_spi_driver);
+
+MODULE_DESCRIPTION("BMP280 SPI bus driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_BMP280);
diff --git a/drivers/iio/pressure/bmp280.h b/drivers/iio/pressure/bmp280.h
new file mode 100644
index 000000000..c791325c7
--- /dev/null
+++ b/drivers/iio/pressure/bmp280.h
@@ -0,0 +1,207 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+/* BMP380 specific registers */
+#define BMP380_REG_CMD			0x7E
+#define BMP380_REG_CONFIG		0x1F
+#define BMP380_REG_ODR			0x1D
+#define BMP380_REG_OSR			0x1C
+#define BMP380_REG_POWER_CONTROL	0x1B
+#define BMP380_REG_IF_CONFIG		0x1A
+#define BMP380_REG_INT_CONTROL		0x19
+#define BMP380_REG_INT_STATUS		0x11
+#define BMP380_REG_EVENT		0x10
+#define BMP380_REG_STATUS		0x03
+#define BMP380_REG_ERROR		0x02
+#define BMP380_REG_ID			0x00
+
+#define BMP380_REG_FIFO_CONFIG_1	0x18
+#define BMP380_REG_FIFO_CONFIG_2	0x17
+#define BMP380_REG_FIFO_WATERMARK_MSB	0x16
+#define BMP380_REG_FIFO_WATERMARK_LSB	0x15
+#define BMP380_REG_FIFO_DATA		0x14
+#define BMP380_REG_FIFO_LENGTH_MSB	0x13
+#define BMP380_REG_FIFO_LENGTH_LSB	0x12
+
+#define BMP380_REG_SENSOR_TIME_MSB	0x0E
+#define BMP380_REG_SENSOR_TIME_LSB	0x0D
+#define BMP380_REG_SENSOR_TIME_XLSB	0x0C
+
+#define BMP380_REG_TEMP_MSB		0x09
+#define BMP380_REG_TEMP_LSB		0x08
+#define BMP380_REG_TEMP_XLSB		0x07
+
+#define BMP380_REG_PRESS_MSB		0x06
+#define BMP380_REG_PRESS_LSB		0x05
+#define BMP380_REG_PRESS_XLSB		0x04
+
+#define BMP380_REG_CALIB_TEMP_START	0x31
+#define BMP380_CALIB_REG_COUNT		21
+
+#define BMP380_FILTER_MASK		GENMASK(3, 1)
+#define BMP380_FILTER_OFF		0
+#define BMP380_FILTER_1X		1
+#define BMP380_FILTER_3X		2
+#define BMP380_FILTER_7X		3
+#define BMP380_FILTER_15X		4
+#define BMP380_FILTER_31X		5
+#define BMP380_FILTER_63X		6
+#define BMP380_FILTER_127X		7
+
+#define BMP380_OSRS_TEMP_MASK		GENMASK(5, 3)
+#define BMP380_OSRS_PRESS_MASK		GENMASK(2, 0)
+
+#define BMP380_ODRS_MASK		GENMASK(4, 0)
+
+#define BMP380_CTRL_SENSORS_MASK	GENMASK(1, 0)
+#define BMP380_CTRL_SENSORS_PRESS_EN	BIT(0)
+#define BMP380_CTRL_SENSORS_TEMP_EN	BIT(1)
+#define BMP380_MODE_MASK		GENMASK(5, 4)
+#define BMP380_MODE_SLEEP		0
+#define BMP380_MODE_FORCED		1
+#define BMP380_MODE_NORMAL		3
+
+#define BMP380_MIN_TEMP			-4000
+#define BMP380_MAX_TEMP			8500
+#define BMP380_MIN_PRES			3000000
+#define BMP380_MAX_PRES			12500000
+
+#define BMP380_CMD_NOOP			0x00
+#define BMP380_CMD_EXTMODE_EN_MID	0x34
+#define BMP380_CMD_FIFO_FLUSH		0xB0
+#define BMP380_CMD_SOFT_RESET		0xB6
+
+#define BMP380_STATUS_CMD_RDY_MASK	BIT(4)
+#define BMP380_STATUS_DRDY_PRESS_MASK	BIT(5)
+#define BMP380_STATUS_DRDY_TEMP_MASK	BIT(6)
+
+#define BMP380_ERR_FATAL_MASK		BIT(0)
+#define BMP380_ERR_CMD_MASK		BIT(1)
+#define BMP380_ERR_CONF_MASK		BIT(2)
+
+#define BMP380_TEMP_SKIPPED		0x800000
+#define BMP380_PRESS_SKIPPED		0x800000
+
+/* BMP280 specific registers */
+#define BMP280_REG_HUMIDITY_LSB		0xFE
+#define BMP280_REG_HUMIDITY_MSB		0xFD
+#define BMP280_REG_TEMP_XLSB		0xFC
+#define BMP280_REG_TEMP_LSB		0xFB
+#define BMP280_REG_TEMP_MSB		0xFA
+#define BMP280_REG_PRESS_XLSB		0xF9
+#define BMP280_REG_PRESS_LSB		0xF8
+#define BMP280_REG_PRESS_MSB		0xF7
+
+/* Helper mask to truncate excess 4 bits on pressure and temp readings */
+#define BMP280_MEAS_TRIM_MASK		GENMASK(24, 4)
+
+#define BMP280_REG_CONFIG		0xF5
+#define BMP280_REG_CTRL_MEAS		0xF4
+#define BMP280_REG_STATUS		0xF3
+#define BMP280_REG_CTRL_HUMIDITY	0xF2
+
+/* Due to non linear mapping, and data sizes we can't do a bulk read */
+#define BMP280_REG_COMP_H1		0xA1
+#define BMP280_REG_COMP_H2		0xE1
+#define BMP280_REG_COMP_H3		0xE3
+#define BMP280_REG_COMP_H4		0xE4
+#define BMP280_REG_COMP_H5		0xE5
+#define BMP280_REG_COMP_H6		0xE7
+
+#define BMP280_REG_COMP_TEMP_START	0x88
+#define BMP280_COMP_TEMP_REG_COUNT	6
+
+#define BMP280_REG_COMP_PRESS_START	0x8E
+#define BMP280_COMP_PRESS_REG_COUNT	18
+
+#define BMP280_COMP_H5_MASK		GENMASK(15, 4)
+
+#define BMP280_CONTIGUOUS_CALIB_REGS	(BMP280_COMP_TEMP_REG_COUNT + \
+					 BMP280_COMP_PRESS_REG_COUNT)
+
+#define BMP280_FILTER_MASK		GENMASK(4, 2)
+#define BMP280_FILTER_OFF		0
+#define BMP280_FILTER_2X		1
+#define BMP280_FILTER_4X		2
+#define BMP280_FILTER_8X		3
+#define BMP280_FILTER_16X		4
+
+#define BMP280_OSRS_HUMIDITY_MASK	GENMASK(2, 0)
+#define BMP280_OSRS_HUMIDITY_SKIP	0
+#define BMP280_OSRS_HUMIDITY_1X		1
+#define BMP280_OSRS_HUMIDITY_2X		2
+#define BMP280_OSRS_HUMIDITY_4X		3
+#define BMP280_OSRS_HUMIDITY_8X		4
+#define BMP280_OSRS_HUMIDITY_16X	5
+
+#define BMP280_OSRS_TEMP_MASK		GENMASK(7, 5)
+#define BMP280_OSRS_TEMP_SKIP		0
+#define BMP280_OSRS_TEMP_1X		1
+#define BMP280_OSRS_TEMP_2X		2
+#define BMP280_OSRS_TEMP_4X		3
+#define BMP280_OSRS_TEMP_8X		4
+#define BMP280_OSRS_TEMP_16X		5
+
+#define BMP280_OSRS_PRESS_MASK		GENMASK(4, 2)
+#define BMP280_OSRS_PRESS_SKIP		0
+#define BMP280_OSRS_PRESS_1X		1
+#define BMP280_OSRS_PRESS_2X		2
+#define BMP280_OSRS_PRESS_4X		3
+#define BMP280_OSRS_PRESS_8X		4
+#define BMP280_OSRS_PRESS_16X		5
+
+#define BMP280_MODE_MASK		GENMASK(1, 0)
+#define BMP280_MODE_SLEEP		0
+#define BMP280_MODE_FORCED		1
+#define BMP280_MODE_NORMAL		3
+
+/* BMP180 specific registers */
+#define BMP180_REG_OUT_XLSB		0xF8
+#define BMP180_REG_OUT_LSB		0xF7
+#define BMP180_REG_OUT_MSB		0xF6
+
+#define BMP180_REG_CALIB_START		0xAA
+#define BMP180_REG_CALIB_COUNT		22
+
+#define BMP180_MEAS_CTRL_MASK		GENMASK(4, 0)
+#define BMP180_MEAS_TEMP		0x0E
+#define BMP180_MEAS_PRESS		0x14
+#define BMP180_MEAS_SCO			BIT(5)
+#define BMP180_OSRS_PRESS_MASK		GENMASK(7, 6)
+#define BMP180_MEAS_PRESS_1X		0
+#define BMP180_MEAS_PRESS_2X		1
+#define BMP180_MEAS_PRESS_4X		2
+#define BMP180_MEAS_PRESS_8X		3
+
+/* BMP180 and BMP280 common registers */
+#define BMP280_REG_CTRL_MEAS		0xF4
+#define BMP280_REG_RESET		0xE0
+#define BMP280_REG_ID			0xD0
+
+#define BMP380_CHIP_ID			0x50
+#define BMP180_CHIP_ID			0x55
+#define BMP280_CHIP_ID			0x58
+#define BME280_CHIP_ID			0x60
+#define BMP280_SOFT_RESET_VAL		0xB6
+
+/* BMP280 register skipped special values */
+#define BMP280_TEMP_SKIPPED		0x80000
+#define BMP280_PRESS_SKIPPED		0x80000
+#define BMP280_HUMIDITY_SKIPPED		0x8000
+
+/* Regmap configurations */
+extern const struct regmap_config bmp180_regmap_config;
+extern const struct regmap_config bmp280_regmap_config;
+extern const struct regmap_config bmp380_regmap_config;
+
+/* Probe called from different transports */
+int bmp280_common_probe(struct device *dev,
+			struct regmap *regmap,
+			unsigned int chip,
+			const char *name,
+			int irq);
+
+/* PM ops */
+extern const struct dev_pm_ops bmp280_dev_pm_ops;
diff --git a/drivers/iio/pressure/cros_ec_baro.c b/drivers/iio/pressure/cros_ec_baro.c
new file mode 100644
index 000000000..2649c2f89
--- /dev/null
+++ b/drivers/iio/pressure/cros_ec_baro.c
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * cros_ec_baro - Driver for barometer sensor behind CrosEC.
+ *
+ * Copyright (C) 2017 Google, Inc
+ */
+
+#include <linux/device.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/common/cros_ec_sensors_core.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/kfifo_buf.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_data/cros_ec_commands.h>
+#include <linux/platform_data/cros_ec_proto.h>
+#include <linux/platform_device.h>
+
+/*
+ * One channel for pressure, the other for timestamp.
+ */
+#define CROS_EC_BARO_MAX_CHANNELS (1 + 1)
+
+/* State data for ec_sensors iio driver. */
+struct cros_ec_baro_state {
+	/* Shared by all sensors */
+	struct cros_ec_sensors_core_state core;
+
+	struct iio_chan_spec channels[CROS_EC_BARO_MAX_CHANNELS];
+};
+
+static int cros_ec_baro_read(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     int *val, int *val2, long mask)
+{
+	struct cros_ec_baro_state *st = iio_priv(indio_dev);
+	u16 data = 0;
+	int ret;
+	int idx = chan->scan_index;
+
+	mutex_lock(&st->core.cmd_lock);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = cros_ec_sensors_read_cmd(indio_dev, 1 << idx,
+					     (s16 *)&data);
+		if (ret)
+			break;
+
+		*val = data;
+		ret = IIO_VAL_INT;
+		break;
+	case IIO_CHAN_INFO_SCALE:
+		st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_RANGE;
+		st->core.param.sensor_range.data = EC_MOTION_SENSE_NO_VALUE;
+
+		ret = cros_ec_motion_send_host_cmd(&st->core, 0);
+		if (ret)
+			break;
+
+		*val = st->core.resp->sensor_range.ret;
+
+		/* scale * in_pressure_raw --> kPa */
+		*val2 = 10 << CROS_EC_SENSOR_BITS;
+		ret = IIO_VAL_FRACTIONAL;
+		break;
+	default:
+		ret = cros_ec_sensors_core_read(&st->core, chan, val, val2,
+						mask);
+		break;
+	}
+
+	mutex_unlock(&st->core.cmd_lock);
+
+	return ret;
+}
+
+static int cros_ec_baro_write(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      int val, int val2, long mask)
+{
+	struct cros_ec_baro_state *st = iio_priv(indio_dev);
+	int ret = 0;
+
+	mutex_lock(&st->core.cmd_lock);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_RANGE;
+		st->core.param.sensor_range.data = val;
+
+		/* Always roundup, so caller gets at least what it asks for. */
+		st->core.param.sensor_range.roundup = 1;
+
+		ret = cros_ec_motion_send_host_cmd(&st->core, 0);
+		if (ret == 0) {
+			st->core.range_updated = true;
+			st->core.curr_range = val;
+		}
+		break;
+	default:
+		ret = cros_ec_sensors_core_write(&st->core, chan, val, val2,
+						 mask);
+		break;
+	}
+
+	mutex_unlock(&st->core.cmd_lock);
+
+	return ret;
+}
+
+static const struct iio_info cros_ec_baro_info = {
+	.read_raw = &cros_ec_baro_read,
+	.write_raw = &cros_ec_baro_write,
+	.read_avail = &cros_ec_sensors_core_read_avail,
+};
+
+static int cros_ec_baro_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct cros_ec_dev *ec_dev = dev_get_drvdata(dev->parent);
+	struct iio_dev *indio_dev;
+	struct cros_ec_baro_state *state;
+	struct iio_chan_spec *channel;
+	int ret;
+
+	if (!ec_dev || !ec_dev->ec_dev) {
+		dev_warn(dev, "No CROS EC device found.\n");
+		return -EINVAL;
+	}
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*state));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	ret = cros_ec_sensors_core_init(pdev, indio_dev, true,
+					cros_ec_sensors_capture);
+	if (ret)
+		return ret;
+
+	indio_dev->info = &cros_ec_baro_info;
+	state = iio_priv(indio_dev);
+	channel = state->channels;
+	/* Common part */
+	channel->info_mask_separate = BIT(IIO_CHAN_INFO_RAW);
+	channel->info_mask_shared_by_all =
+		BIT(IIO_CHAN_INFO_SCALE) |
+		BIT(IIO_CHAN_INFO_SAMP_FREQ);
+	channel->info_mask_shared_by_all_available =
+		BIT(IIO_CHAN_INFO_SAMP_FREQ);
+	channel->scan_type.realbits = CROS_EC_SENSOR_BITS;
+	channel->scan_type.storagebits = CROS_EC_SENSOR_BITS;
+	channel->scan_type.shift = 0;
+	channel->scan_index = 0;
+	channel->ext_info = cros_ec_sensors_ext_info;
+	channel->scan_type.sign = 'u';
+
+	/* Sensor specific */
+	switch (state->core.type) {
+	case MOTIONSENSE_TYPE_BARO:
+		channel->type = IIO_PRESSURE;
+		break;
+	default:
+		dev_warn(dev, "Unknown motion sensor\n");
+		return -EINVAL;
+	}
+
+	/* Timestamp */
+	channel++;
+	channel->type = IIO_TIMESTAMP;
+	channel->channel = -1;
+	channel->scan_index = 1;
+	channel->scan_type.sign = 's';
+	channel->scan_type.realbits = 64;
+	channel->scan_type.storagebits = 64;
+
+	indio_dev->channels = state->channels;
+	indio_dev->num_channels = CROS_EC_BARO_MAX_CHANNELS;
+
+	state->core.read_ec_sensors_data = cros_ec_sensors_read_cmd;
+
+	return cros_ec_sensors_core_register(dev, indio_dev,
+					     cros_ec_sensors_push_data);
+}
+
+static const struct platform_device_id cros_ec_baro_ids[] = {
+	{
+		.name = "cros-ec-baro",
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, cros_ec_baro_ids);
+
+static struct platform_driver cros_ec_baro_platform_driver = {
+	.driver = {
+		.name	= "cros-ec-baro",
+		.pm	= &cros_ec_sensors_pm_ops,
+	},
+	.probe		= cros_ec_baro_probe,
+	.id_table	= cros_ec_baro_ids,
+};
+module_platform_driver(cros_ec_baro_platform_driver);
+
+MODULE_DESCRIPTION("ChromeOS EC barometer sensor driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/dlhl60d.c b/drivers/iio/pressure/dlhl60d.c
new file mode 100644
index 000000000..f0b0d198c
--- /dev/null
+++ b/drivers/iio/pressure/dlhl60d.c
@@ -0,0 +1,372 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * All Sensors DLH series low voltage digital pressure sensors
+ *
+ * Copyright (c) 2019 AVL DiTEST GmbH
+ *   Tomislav Denis <tomislav.denis@avl.com>
+ *
+ * Datasheet: https://www.allsensors.com/cad/DS-0355_Rev_B.PDF
+ */
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <asm/unaligned.h>
+
+/* Commands */
+#define DLH_START_SINGLE    0xAA
+
+/* Status bits */
+#define DLH_STATUS_OK       0x40
+
+/* DLH  data format */
+#define DLH_NUM_READ_BYTES  7
+#define DLH_NUM_DATA_BYTES  3
+#define DLH_NUM_PR_BITS     24
+#define DLH_NUM_TEMP_BITS   24
+
+/* DLH  timings */
+#define DLH_SINGLE_DUT_MS   5
+
+enum dhl_ids {
+	dlhl60d,
+	dlhl60g,
+};
+
+struct dlh_info {
+	u8 osdig;           /* digital offset factor */
+	unsigned int fss;   /* full scale span (inch H2O) */
+};
+
+struct dlh_state {
+	struct i2c_client *client;
+	struct dlh_info info;
+	bool use_interrupt;
+	struct completion completion;
+	u8 rx_buf[DLH_NUM_READ_BYTES];
+};
+
+static struct dlh_info dlh_info_tbl[] = {
+	[dlhl60d] = {
+		.osdig = 2,
+		.fss = 120,
+	},
+	[dlhl60g] = {
+		.osdig = 10,
+		.fss = 60,
+	},
+};
+
+
+static int dlh_cmd_start_single(struct dlh_state *st)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte(st->client, DLH_START_SINGLE);
+	if (ret)
+		dev_err(&st->client->dev,
+			"%s: I2C write byte failed\n", __func__);
+
+	return ret;
+}
+
+static int dlh_cmd_read_data(struct dlh_state *st)
+{
+	int ret;
+
+	ret = i2c_master_recv(st->client, st->rx_buf, DLH_NUM_READ_BYTES);
+	if (ret < 0) {
+		dev_err(&st->client->dev,
+			"%s: I2C read block failed\n", __func__);
+		return ret;
+	}
+
+	if (st->rx_buf[0] != DLH_STATUS_OK) {
+		dev_err(&st->client->dev,
+			"%s: invalid status 0x%02x\n", __func__, st->rx_buf[0]);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static int dlh_start_capture_and_read(struct dlh_state *st)
+{
+	int ret;
+
+	if (st->use_interrupt)
+		reinit_completion(&st->completion);
+
+	ret = dlh_cmd_start_single(st);
+	if (ret)
+		return ret;
+
+	if (st->use_interrupt) {
+		ret = wait_for_completion_timeout(&st->completion,
+			msecs_to_jiffies(DLH_SINGLE_DUT_MS));
+		if (!ret) {
+			dev_err(&st->client->dev,
+				"%s: conversion timed out\n", __func__);
+			return -ETIMEDOUT;
+		}
+	} else {
+		mdelay(DLH_SINGLE_DUT_MS);
+	}
+
+	return dlh_cmd_read_data(st);
+}
+
+static int dlh_read_direct(struct dlh_state *st,
+	unsigned int *pressure, unsigned int *temperature)
+{
+	int ret;
+
+	ret = dlh_start_capture_and_read(st);
+	if (ret)
+		return ret;
+
+	*pressure = get_unaligned_be24(&st->rx_buf[1]);
+	*temperature = get_unaligned_be24(&st->rx_buf[4]);
+
+	return 0;
+}
+
+static int dlh_read_raw(struct iio_dev *indio_dev,
+	struct iio_chan_spec const *channel, int *value,
+	int *value2, long mask)
+{
+	struct dlh_state *st = iio_priv(indio_dev);
+	unsigned int pressure, temperature;
+	int ret;
+	s64 tmp;
+	s32 rem;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		ret = dlh_read_direct(st, &pressure, &temperature);
+		iio_device_release_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		switch (channel->type) {
+		case IIO_PRESSURE:
+			*value = pressure;
+			return IIO_VAL_INT;
+
+		case IIO_TEMP:
+			*value = temperature;
+			return IIO_VAL_INT;
+
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SCALE:
+		switch (channel->type) {
+		case IIO_PRESSURE:
+			tmp = div_s64(125LL * st->info.fss * 24909 * 100,
+				1 << DLH_NUM_PR_BITS);
+			tmp = div_s64_rem(tmp, 1000000000LL, &rem);
+			*value = tmp;
+			*value2 = rem;
+			return IIO_VAL_INT_PLUS_NANO;
+
+		case IIO_TEMP:
+			*value = 125 * 1000;
+			*value2 = DLH_NUM_TEMP_BITS;
+			return IIO_VAL_FRACTIONAL_LOG2;
+
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_OFFSET:
+		switch (channel->type) {
+		case IIO_PRESSURE:
+			*value = -125 * st->info.fss * 24909;
+			*value2 = 100 * st->info.osdig * 100000;
+			return IIO_VAL_FRACTIONAL;
+
+		case IIO_TEMP:
+			*value = -40 * 1000;
+			return IIO_VAL_INT;
+
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info dlh_info = {
+	.read_raw = dlh_read_raw,
+};
+
+static const struct iio_chan_spec dlh_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.indexed = 1,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type =
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OFFSET),
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 'u',
+			.realbits = DLH_NUM_PR_BITS,
+			.storagebits = 32,
+			.shift = 8,
+			.endianness = IIO_BE,
+		},
+	}, {
+		.type = IIO_TEMP,
+		.indexed = 1,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type =
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OFFSET),
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 'u',
+			.realbits = DLH_NUM_TEMP_BITS,
+			.storagebits = 32,
+			.shift = 8,
+			.endianness = IIO_BE,
+		},
+	}
+};
+
+static irqreturn_t dlh_trigger_handler(int irq, void *private)
+{
+	struct iio_poll_func *pf = private;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct dlh_state *st = iio_priv(indio_dev);
+	int ret;
+	unsigned int chn, i = 0;
+	__be32 tmp_buf[2];
+
+	ret = dlh_start_capture_and_read(st);
+	if (ret)
+		goto out;
+
+	for_each_set_bit(chn, indio_dev->active_scan_mask,
+		indio_dev->masklength) {
+		memcpy(tmp_buf + i,
+			&st->rx_buf[1] + chn * DLH_NUM_DATA_BYTES,
+			DLH_NUM_DATA_BYTES);
+		i++;
+	}
+
+	iio_push_to_buffers(indio_dev, tmp_buf);
+
+out:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t dlh_interrupt(int irq, void *private)
+{
+	struct iio_dev *indio_dev = private;
+	struct dlh_state *st = iio_priv(indio_dev);
+
+	complete(&st->completion);
+
+	return IRQ_HANDLED;
+};
+
+static int dlh_probe(struct i2c_client *client,
+	const struct i2c_device_id *id)
+{
+	struct dlh_state *st;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter,
+		I2C_FUNC_I2C | I2C_FUNC_SMBUS_WRITE_BYTE)) {
+		dev_err(&client->dev,
+			"adapter doesn't support required i2c functionality\n");
+		return -EOPNOTSUPP;
+	}
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st));
+	if (!indio_dev) {
+		dev_err(&client->dev, "failed to allocate iio device\n");
+		return -ENOMEM;
+	}
+
+	i2c_set_clientdata(client, indio_dev);
+
+	st = iio_priv(indio_dev);
+	st->info = dlh_info_tbl[id->driver_data];
+	st->client = client;
+	st->use_interrupt = false;
+
+	indio_dev->name = id->name;
+	indio_dev->info = &dlh_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels =  dlh_channels;
+	indio_dev->num_channels = ARRAY_SIZE(dlh_channels);
+
+	if (client->irq > 0) {
+		ret = devm_request_threaded_irq(&client->dev, client->irq,
+			dlh_interrupt, NULL,
+			IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+			id->name, indio_dev);
+		if (ret) {
+			dev_err(&client->dev, "failed to allocate threaded irq");
+			return ret;
+		}
+
+		st->use_interrupt = true;
+		init_completion(&st->completion);
+	}
+
+	ret = devm_iio_triggered_buffer_setup(&client->dev, indio_dev,
+		NULL, &dlh_trigger_handler, NULL);
+	if (ret) {
+		dev_err(&client->dev, "failed to setup iio buffer\n");
+		return ret;
+	}
+
+	ret = devm_iio_device_register(&client->dev, indio_dev);
+	if (ret)
+		dev_err(&client->dev, "failed to register iio device\n");
+
+	return ret;
+}
+
+static const struct of_device_id dlh_of_match[] = {
+	{ .compatible = "asc,dlhl60d" },
+	{ .compatible = "asc,dlhl60g" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, dlh_of_match);
+
+static const struct i2c_device_id dlh_id[] = {
+	{ "dlhl60d",    dlhl60d },
+	{ "dlhl60g",    dlhl60g },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, dlh_id);
+
+static struct i2c_driver dlh_driver = {
+	.driver = {
+		.name = "dlhl60d",
+		.of_match_table = dlh_of_match,
+	},
+	.probe = dlh_probe,
+	.id_table = dlh_id,
+};
+module_i2c_driver(dlh_driver);
+
+MODULE_AUTHOR("Tomislav Denis <tomislav.denis@avl.com>");
+MODULE_DESCRIPTION("Driver for All Sensors DLH series pressure sensors");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
new file mode 100644
index 000000000..db1b1e482
--- /dev/null
+++ b/drivers/iio/pressure/dps310.c
@@ -0,0 +1,897 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright IBM Corp 2019
+/*
+ * The DPS310 is a barometric pressure and temperature sensor.
+ * Currently only reading a single temperature is supported by
+ * this driver.
+ *
+ * https://www.infineon.com/dgdl/?fileId=5546d462576f34750157750826c42242
+ *
+ * Temperature calculation:
+ *   c0 * 0.5 + c1 * T_raw / kT °C
+ *
+ * TODO:
+ *  - Optionally support the FIFO
+ */
+
+#include <linux/i2c.h>
+#include <linux/limits.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#define DPS310_DEV_NAME		"dps310"
+
+#define DPS310_PRS_B0		0x00
+#define DPS310_PRS_B1		0x01
+#define DPS310_PRS_B2		0x02
+#define DPS310_TMP_B0		0x03
+#define DPS310_TMP_B1		0x04
+#define DPS310_TMP_B2		0x05
+#define DPS310_PRS_CFG		0x06
+#define  DPS310_PRS_RATE_BITS	GENMASK(6, 4)
+#define  DPS310_PRS_PRC_BITS	GENMASK(3, 0)
+#define DPS310_TMP_CFG		0x07
+#define  DPS310_TMP_RATE_BITS	GENMASK(6, 4)
+#define  DPS310_TMP_PRC_BITS	GENMASK(3, 0)
+#define  DPS310_TMP_EXT		BIT(7)
+#define DPS310_MEAS_CFG		0x08
+#define  DPS310_MEAS_CTRL_BITS	GENMASK(2, 0)
+#define   DPS310_PRS_EN		BIT(0)
+#define   DPS310_TEMP_EN	BIT(1)
+#define   DPS310_BACKGROUND	BIT(2)
+#define  DPS310_PRS_RDY		BIT(4)
+#define  DPS310_TMP_RDY		BIT(5)
+#define  DPS310_SENSOR_RDY	BIT(6)
+#define  DPS310_COEF_RDY	BIT(7)
+#define DPS310_CFG_REG		0x09
+#define  DPS310_INT_HL		BIT(7)
+#define  DPS310_TMP_SHIFT_EN	BIT(3)
+#define  DPS310_PRS_SHIFT_EN	BIT(4)
+#define  DPS310_FIFO_EN		BIT(5)
+#define  DPS310_SPI_EN		BIT(6)
+#define DPS310_RESET		0x0c
+#define  DPS310_RESET_MAGIC	0x09
+#define DPS310_COEF_BASE	0x10
+
+/* Make sure sleep time is <= 30ms for usleep_range */
+#define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)
+/* Silently handle error in rate value here */
+#define DPS310_POLL_TIMEOUT_US(rc)	((rc) <= 0 ? 1000000 : 1000000 / (rc))
+
+#define DPS310_PRS_BASE		DPS310_PRS_B0
+#define DPS310_TMP_BASE		DPS310_TMP_B0
+
+/*
+ * These values (defined in the spec) indicate how to scale the raw register
+ * values for each level of precision available.
+ */
+static const int scale_factors[] = {
+	 524288,
+	1572864,
+	3670016,
+	7864320,
+	 253952,
+	 516096,
+	1040384,
+	2088960,
+};
+
+struct dps310_data {
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct mutex lock;	/* Lock for sequential HW access functions */
+
+	s32 c0, c1;
+	s32 c00, c10, c20, c30, c01, c11, c21;
+	s32 pressure_raw;
+	s32 temp_raw;
+	bool timeout_recovery_failed;
+};
+
+static const struct iio_chan_spec dps310_channels[] = {
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO) |
+			BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+			BIT(IIO_CHAN_INFO_PROCESSED),
+	},
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO) |
+			BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+			BIT(IIO_CHAN_INFO_PROCESSED),
+	},
+};
+
+/* To be called after checking the COEF_RDY bit in MEAS_CFG */
+static int dps310_get_coefs(struct dps310_data *data)
+{
+	int rc;
+	u8 coef[18];
+	u32 c0, c1;
+	u32 c00, c10, c20, c30, c01, c11, c21;
+
+	/* Read all sensor calibration coefficients from the COEF registers. */
+	rc = regmap_bulk_read(data->regmap, DPS310_COEF_BASE, coef,
+			      sizeof(coef));
+	if (rc < 0)
+		return rc;
+
+	/*
+	 * Calculate temperature calibration coefficients c0 and c1. The
+	 * numbers are 12-bit 2's complement numbers.
+	 */
+	c0 = (coef[0] << 4) | (coef[1] >> 4);
+	data->c0 = sign_extend32(c0, 11);
+
+	c1 = ((coef[1] & GENMASK(3, 0)) << 8) | coef[2];
+	data->c1 = sign_extend32(c1, 11);
+
+	/*
+	 * Calculate pressure calibration coefficients. c00 and c10 are 20 bit
+	 * 2's complement numbers, while the rest are 16 bit 2's complement
+	 * numbers.
+	 */
+	c00 = (coef[3] << 12) | (coef[4] << 4) | (coef[5] >> 4);
+	data->c00 = sign_extend32(c00, 19);
+
+	c10 = ((coef[5] & GENMASK(3, 0)) << 16) | (coef[6] << 8) | coef[7];
+	data->c10 = sign_extend32(c10, 19);
+
+	c01 = (coef[8] << 8) | coef[9];
+	data->c01 = sign_extend32(c01, 15);
+
+	c11 = (coef[10] << 8) | coef[11];
+	data->c11 = sign_extend32(c11, 15);
+
+	c20 = (coef[12] << 8) | coef[13];
+	data->c20 = sign_extend32(c20, 15);
+
+	c21 = (coef[14] << 8) | coef[15];
+	data->c21 = sign_extend32(c21, 15);
+
+	c30 = (coef[16] << 8) | coef[17];
+	data->c30 = sign_extend32(c30, 15);
+
+	return 0;
+}
+
+/*
+ * Some versions of the chip will read temperatures in the ~60C range when
+ * it's actually ~20C. This is the manufacturer recommended workaround
+ * to correct the issue. The registers used below are undocumented.
+ */
+static int dps310_temp_workaround(struct dps310_data *data)
+{
+	int rc;
+	int reg;
+
+	rc = regmap_read(data->regmap, 0x32, &reg);
+	if (rc)
+		return rc;
+
+	/*
+	 * If bit 1 is set then the device is okay, and the workaround does not
+	 * need to be applied
+	 */
+	if (reg & BIT(1))
+		return 0;
+
+	rc = regmap_write(data->regmap, 0x0e, 0xA5);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x0f, 0x96);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x62, 0x02);
+	if (rc)
+		return rc;
+
+	rc = regmap_write(data->regmap, 0x0e, 0x00);
+	if (rc)
+		return rc;
+
+	return regmap_write(data->regmap, 0x0f, 0x00);
+}
+
+static int dps310_startup(struct dps310_data *data)
+{
+	int rc;
+	int ready;
+
+	/*
+	 * Set up pressure sensor in single sample, one measurement per second
+	 * mode
+	 */
+	rc = regmap_write(data->regmap, DPS310_PRS_CFG, 0);
+	if (rc)
+		return rc;
+
+	/*
+	 * Set up external (MEMS) temperature sensor in single sample, one
+	 * measurement per second mode
+	 */
+	rc = regmap_write(data->regmap, DPS310_TMP_CFG, DPS310_TMP_EXT);
+	if (rc)
+		return rc;
+
+	/* Temp and pressure shifts are disabled when PRC <= 8 */
+	rc = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+			       DPS310_PRS_SHIFT_EN | DPS310_TMP_SHIFT_EN, 0);
+	if (rc)
+		return rc;
+
+	/* MEAS_CFG doesn't update correctly unless first written with 0 */
+	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
+			       DPS310_MEAS_CTRL_BITS, 0);
+	if (rc)
+		return rc;
+
+	/* Turn on temperature and pressure measurement in the background */
+	rc = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
+			       DPS310_MEAS_CTRL_BITS, DPS310_PRS_EN |
+			       DPS310_TEMP_EN | DPS310_BACKGROUND);
+	if (rc)
+		return rc;
+
+	/*
+	 * Calibration coefficients required for reporting temperature.
+	 * They are available 40ms after the device has started
+	 */
+	rc = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
+				      ready & DPS310_COEF_RDY, 10000, 40000);
+	if (rc)
+		return rc;
+
+	rc = dps310_get_coefs(data);
+	if (rc)
+		return rc;
+
+	return dps310_temp_workaround(data);
+}
+
+static int dps310_get_pres_precision(struct dps310_data *data)
+{
+	int rc;
+	int val;
+
+	rc = regmap_read(data->regmap, DPS310_PRS_CFG, &val);
+	if (rc < 0)
+		return rc;
+
+	return BIT(val & GENMASK(2, 0));
+}
+
+static int dps310_get_temp_precision(struct dps310_data *data)
+{
+	int rc;
+	int val;
+
+	rc = regmap_read(data->regmap, DPS310_TMP_CFG, &val);
+	if (rc < 0)
+		return rc;
+
+	/*
+	 * Scale factor is bottom 4 bits of the register, but 1111 is
+	 * reserved so just grab bottom three
+	 */
+	return BIT(val & GENMASK(2, 0));
+}
+
+/* Called with lock held */
+static int dps310_set_pres_precision(struct dps310_data *data, int val)
+{
+	int rc;
+	u8 shift_en;
+
+	if (val < 0 || val > 128)
+		return -EINVAL;
+
+	shift_en = val >= 16 ? DPS310_PRS_SHIFT_EN : 0;
+	rc = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+			       DPS310_PRS_SHIFT_EN, shift_en);
+	if (rc)
+		return rc;
+
+	return regmap_update_bits(data->regmap, DPS310_PRS_CFG,
+				  DPS310_PRS_PRC_BITS, ilog2(val));
+}
+
+/* Called with lock held */
+static int dps310_set_temp_precision(struct dps310_data *data, int val)
+{
+	int rc;
+	u8 shift_en;
+
+	if (val < 0 || val > 128)
+		return -EINVAL;
+
+	shift_en = val >= 16 ? DPS310_TMP_SHIFT_EN : 0;
+	rc = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+			       DPS310_TMP_SHIFT_EN, shift_en);
+	if (rc)
+		return rc;
+
+	return regmap_update_bits(data->regmap, DPS310_TMP_CFG,
+				  DPS310_TMP_PRC_BITS, ilog2(val));
+}
+
+/* Called with lock held */
+static int dps310_set_pres_samp_freq(struct dps310_data *data, int freq)
+{
+	u8 val;
+
+	if (freq < 0 || freq > 128)
+		return -EINVAL;
+
+	val = ilog2(freq) << 4;
+
+	return regmap_update_bits(data->regmap, DPS310_PRS_CFG,
+				  DPS310_PRS_RATE_BITS, val);
+}
+
+/* Called with lock held */
+static int dps310_set_temp_samp_freq(struct dps310_data *data, int freq)
+{
+	u8 val;
+
+	if (freq < 0 || freq > 128)
+		return -EINVAL;
+
+	val = ilog2(freq) << 4;
+
+	return regmap_update_bits(data->regmap, DPS310_TMP_CFG,
+				  DPS310_TMP_RATE_BITS, val);
+}
+
+static int dps310_get_pres_samp_freq(struct dps310_data *data)
+{
+	int rc;
+	int val;
+
+	rc = regmap_read(data->regmap, DPS310_PRS_CFG, &val);
+	if (rc < 0)
+		return rc;
+
+	return BIT((val & DPS310_PRS_RATE_BITS) >> 4);
+}
+
+static int dps310_get_temp_samp_freq(struct dps310_data *data)
+{
+	int rc;
+	int val;
+
+	rc = regmap_read(data->regmap, DPS310_TMP_CFG, &val);
+	if (rc < 0)
+		return rc;
+
+	return BIT((val & DPS310_TMP_RATE_BITS) >> 4);
+}
+
+static int dps310_get_pres_k(struct dps310_data *data)
+{
+	int rc = dps310_get_pres_precision(data);
+
+	if (rc < 0)
+		return rc;
+
+	return scale_factors[ilog2(rc)];
+}
+
+static int dps310_get_temp_k(struct dps310_data *data)
+{
+	int rc = dps310_get_temp_precision(data);
+
+	if (rc < 0)
+		return rc;
+
+	return scale_factors[ilog2(rc)];
+}
+
+static int dps310_reset_wait(struct dps310_data *data)
+{
+	int rc;
+
+	rc = regmap_write(data->regmap, DPS310_RESET, DPS310_RESET_MAGIC);
+	if (rc)
+		return rc;
+
+	/* Wait for device chip access: 15ms in specification */
+	usleep_range(15000, 55000);
+	return 0;
+}
+
+static int dps310_reset_reinit(struct dps310_data *data)
+{
+	int rc;
+
+	rc = dps310_reset_wait(data);
+	if (rc)
+		return rc;
+
+	return dps310_startup(data);
+}
+
+static int dps310_ready_status(struct dps310_data *data, int ready_bit, int timeout)
+{
+	int sleep = DPS310_POLL_SLEEP_US(timeout);
+	int ready;
+
+	return regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready, ready & ready_bit,
+					sleep, timeout);
+}
+
+static int dps310_ready(struct dps310_data *data, int ready_bit, int timeout)
+{
+	int rc;
+
+	rc = dps310_ready_status(data, ready_bit, timeout);
+	if (rc) {
+		if (rc == -ETIMEDOUT && !data->timeout_recovery_failed) {
+			/* Reset and reinitialize the chip. */
+			if (dps310_reset_reinit(data)) {
+				data->timeout_recovery_failed = true;
+			} else {
+				/* Try again to get sensor ready status. */
+				if (dps310_ready_status(data, ready_bit, timeout))
+					data->timeout_recovery_failed = true;
+				else
+					return 0;
+			}
+		}
+
+		return rc;
+	}
+
+	data->timeout_recovery_failed = false;
+	return 0;
+}
+
+static int dps310_read_pres_raw(struct dps310_data *data)
+{
+	int rc;
+	int rate;
+	int timeout;
+	s32 raw;
+	u8 val[3];
+
+	if (mutex_lock_interruptible(&data->lock))
+		return -EINTR;
+
+	rate = dps310_get_pres_samp_freq(data);
+	timeout = DPS310_POLL_TIMEOUT_US(rate);
+
+	/* Poll for sensor readiness; base the timeout upon the sample rate. */
+	rc = dps310_ready(data, DPS310_PRS_RDY, timeout);
+	if (rc)
+		goto done;
+
+	rc = regmap_bulk_read(data->regmap, DPS310_PRS_BASE, val, sizeof(val));
+	if (rc < 0)
+		goto done;
+
+	raw = (val[0] << 16) | (val[1] << 8) | val[2];
+	data->pressure_raw = sign_extend32(raw, 23);
+
+done:
+	mutex_unlock(&data->lock);
+	return rc;
+}
+
+/* Called with lock held */
+static int dps310_read_temp_ready(struct dps310_data *data)
+{
+	int rc;
+	u8 val[3];
+	s32 raw;
+
+	rc = regmap_bulk_read(data->regmap, DPS310_TMP_BASE, val, sizeof(val));
+	if (rc < 0)
+		return rc;
+
+	raw = (val[0] << 16) | (val[1] << 8) | val[2];
+	data->temp_raw = sign_extend32(raw, 23);
+
+	return 0;
+}
+
+static int dps310_read_temp_raw(struct dps310_data *data)
+{
+	int rc;
+	int rate;
+	int timeout;
+
+	if (mutex_lock_interruptible(&data->lock))
+		return -EINTR;
+
+	rate = dps310_get_temp_samp_freq(data);
+	timeout = DPS310_POLL_TIMEOUT_US(rate);
+
+	/* Poll for sensor readiness; base the timeout upon the sample rate. */
+	rc = dps310_ready(data, DPS310_TMP_RDY, timeout);
+	if (rc)
+		goto done;
+
+	rc = dps310_read_temp_ready(data);
+
+done:
+	mutex_unlock(&data->lock);
+	return rc;
+}
+
+static bool dps310_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case DPS310_PRS_CFG:
+	case DPS310_TMP_CFG:
+	case DPS310_MEAS_CFG:
+	case DPS310_CFG_REG:
+	case DPS310_RESET:
+	/* No documentation available on the registers below */
+	case 0x0e:
+	case 0x0f:
+	case 0x62:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool dps310_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case DPS310_PRS_B0:
+	case DPS310_PRS_B1:
+	case DPS310_PRS_B2:
+	case DPS310_TMP_B0:
+	case DPS310_TMP_B1:
+	case DPS310_TMP_B2:
+	case DPS310_MEAS_CFG:
+	case 0x32:	/* No documentation available on this register */
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int dps310_write_raw(struct iio_dev *iio,
+			    struct iio_chan_spec const *chan, int val,
+			    int val2, long mask)
+{
+	int rc;
+	struct dps310_data *data = iio_priv(iio);
+
+	if (mutex_lock_interruptible(&data->lock))
+		return -EINTR;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			rc = dps310_set_pres_samp_freq(data, val);
+			break;
+
+		case IIO_TEMP:
+			rc = dps310_set_temp_samp_freq(data, val);
+			break;
+
+		default:
+			rc = -EINVAL;
+			break;
+		}
+		break;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			rc = dps310_set_pres_precision(data, val);
+			break;
+
+		case IIO_TEMP:
+			rc = dps310_set_temp_precision(data, val);
+			break;
+
+		default:
+			rc = -EINVAL;
+			break;
+		}
+		break;
+
+	default:
+		rc = -EINVAL;
+		break;
+	}
+
+	mutex_unlock(&data->lock);
+	return rc;
+}
+
+static int dps310_calculate_pressure(struct dps310_data *data)
+{
+	int i;
+	int rc;
+	int t_ready;
+	int kpi = dps310_get_pres_k(data);
+	int kti = dps310_get_temp_k(data);
+	s64 rem = 0ULL;
+	s64 pressure = 0ULL;
+	s64 p;
+	s64 t;
+	s64 denoms[7];
+	s64 nums[7];
+	s64 rems[7];
+	s64 kp;
+	s64 kt;
+
+	if (kpi < 0)
+		return kpi;
+
+	if (kti < 0)
+		return kti;
+
+	kp = (s64)kpi;
+	kt = (s64)kti;
+
+	/* Refresh temp if it's ready, otherwise just use the latest value */
+	if (mutex_trylock(&data->lock)) {
+		rc = regmap_read(data->regmap, DPS310_MEAS_CFG, &t_ready);
+		if (rc >= 0 && t_ready & DPS310_TMP_RDY)
+			dps310_read_temp_ready(data);
+
+		mutex_unlock(&data->lock);
+	}
+
+	p = (s64)data->pressure_raw;
+	t = (s64)data->temp_raw;
+
+	/* Section 4.9.1 of the DPS310 spec; algebra'd to avoid underflow */
+	nums[0] = (s64)data->c00;
+	denoms[0] = 1LL;
+	nums[1] = p * (s64)data->c10;
+	denoms[1] = kp;
+	nums[2] = p * p * (s64)data->c20;
+	denoms[2] = kp * kp;
+	nums[3] = p * p * p * (s64)data->c30;
+	denoms[3] = kp * kp * kp;
+	nums[4] = t * (s64)data->c01;
+	denoms[4] = kt;
+	nums[5] = t * p * (s64)data->c11;
+	denoms[5] = kp * kt;
+	nums[6] = t * p * p * (s64)data->c21;
+	denoms[6] = kp * kp * kt;
+
+	/* Kernel lacks a div64_s64_rem function; denoms are all positive */
+	for (i = 0; i < 7; ++i) {
+		u64 irem;
+
+		if (nums[i] < 0LL) {
+			pressure -= div64_u64_rem(-nums[i], denoms[i], &irem);
+			rems[i] = -irem;
+		} else {
+			pressure += div64_u64_rem(nums[i], denoms[i], &irem);
+			rems[i] = (s64)irem;
+		}
+	}
+
+	/* Increase precision and calculate the remainder sum */
+	for (i = 0; i < 7; ++i)
+		rem += div64_s64((s64)rems[i] * 1000000000LL, denoms[i]);
+
+	pressure += div_s64(rem, 1000000000LL);
+	if (pressure < 0LL)
+		return -ERANGE;
+
+	return (int)min_t(s64, pressure, INT_MAX);
+}
+
+static int dps310_read_pressure(struct dps310_data *data, int *val, int *val2,
+				long mask)
+{
+	int rc;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		rc = dps310_get_pres_samp_freq(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_PROCESSED:
+		rc = dps310_read_pres_raw(data);
+		if (rc)
+			return rc;
+
+		rc = dps310_calculate_pressure(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		*val2 = 1000; /* Convert Pa to KPa per IIO ABI */
+		return IIO_VAL_FRACTIONAL;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		rc = dps310_get_pres_precision(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static int dps310_calculate_temp(struct dps310_data *data)
+{
+	s64 c0;
+	s64 t;
+	int kt = dps310_get_temp_k(data);
+
+	if (kt < 0)
+		return kt;
+
+	/* Obtain inverse-scaled offset */
+	c0 = div_s64((s64)kt * (s64)data->c0, 2);
+
+	/* Add the offset to the unscaled temperature */
+	t = c0 + ((s64)data->temp_raw * (s64)data->c1);
+
+	/* Convert to milliCelsius and scale the temperature */
+	return (int)div_s64(t * 1000LL, kt);
+}
+
+static int dps310_read_temp(struct dps310_data *data, int *val, int *val2,
+			    long mask)
+{
+	int rc;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		rc = dps310_get_temp_samp_freq(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_PROCESSED:
+		rc = dps310_read_temp_raw(data);
+		if (rc)
+			return rc;
+
+		rc = dps310_calculate_temp(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		rc = dps310_get_temp_precision(data);
+		if (rc < 0)
+			return rc;
+
+		*val = rc;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static int dps310_read_raw(struct iio_dev *iio,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	struct dps310_data *data = iio_priv(iio);
+
+	switch (chan->type) {
+	case IIO_PRESSURE:
+		return dps310_read_pressure(data, val, val2, mask);
+
+	case IIO_TEMP:
+		return dps310_read_temp(data, val, val2, mask);
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static void dps310_reset(void *action_data)
+{
+	struct dps310_data *data = action_data;
+
+	dps310_reset_wait(data);
+}
+
+static const struct regmap_config dps310_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.writeable_reg = dps310_is_writeable_reg,
+	.volatile_reg = dps310_is_volatile_reg,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 0x62, /* No documentation available on this register */
+};
+
+static const struct iio_info dps310_info = {
+	.read_raw = dps310_read_raw,
+	.write_raw = dps310_write_raw,
+};
+
+static int dps310_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct dps310_data *data;
+	struct iio_dev *iio;
+	int rc;
+
+	iio = devm_iio_device_alloc(&client->dev,  sizeof(*data));
+	if (!iio)
+		return -ENOMEM;
+
+	data = iio_priv(iio);
+	data->client = client;
+	mutex_init(&data->lock);
+
+	iio->name = id->name;
+	iio->channels = dps310_channels;
+	iio->num_channels = ARRAY_SIZE(dps310_channels);
+	iio->info = &dps310_info;
+	iio->modes = INDIO_DIRECT_MODE;
+
+	data->regmap = devm_regmap_init_i2c(client, &dps310_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);
+
+	/* Register to run the device reset when the device is removed */
+	rc = devm_add_action_or_reset(&client->dev, dps310_reset, data);
+	if (rc)
+		return rc;
+
+	rc = dps310_startup(data);
+	if (rc)
+		return rc;
+
+	rc = devm_iio_device_register(&client->dev, iio);
+	if (rc)
+		return rc;
+
+	i2c_set_clientdata(client, iio);
+
+	return 0;
+}
+
+static const struct i2c_device_id dps310_id[] = {
+	{ DPS310_DEV_NAME, 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, dps310_id);
+
+static const struct acpi_device_id dps310_acpi_match[] = {
+	{ "IFX3100" },
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, dps310_acpi_match);
+
+static struct i2c_driver dps310_driver = {
+	.driver = {
+		.name = DPS310_DEV_NAME,
+		.acpi_match_table = dps310_acpi_match,
+	},
+	.probe = dps310_probe,
+	.id_table = dps310_id,
+};
+module_i2c_driver(dps310_driver);
+
+MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
+MODULE_DESCRIPTION("Infineon DPS310 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/hid-sensor-press.c b/drivers/iio/pressure/hid-sensor-press.c
new file mode 100644
index 000000000..a9215eb32
--- /dev/null
+++ b/drivers/iio/pressure/hid-sensor-press.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * HID Sensors Driver
+ * Copyright (c) 2014, Intel Corporation.
+ */
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/slab.h>
+#include <linux/hid-sensor-hub.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include "../common/hid-sensors/hid-sensor-trigger.h"
+
+enum {
+	CHANNEL_SCAN_INDEX_PRESSURE,
+	CHANNEL_SCAN_INDEX_TIMESTAMP,
+};
+
+struct press_state {
+	struct hid_sensor_hub_callbacks callbacks;
+	struct hid_sensor_common common_attributes;
+	struct hid_sensor_hub_attribute_info press_attr;
+	struct {
+		u32 press_data;
+		u64 timestamp __aligned(8);
+	} scan;
+	int scale_pre_decml;
+	int scale_post_decml;
+	int scale_precision;
+	int value_offset;
+	s64 timestamp;
+};
+
+static const u32 press_sensitivity_addresses[] = {
+	HID_USAGE_SENSOR_DATA_ATMOSPHERIC_PRESSURE,
+	HID_USAGE_SENSOR_ATMOSPHERIC_PRESSURE
+};
+
+/* Channel definitions */
+static const struct iio_chan_spec press_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) |
+		BIT(IIO_CHAN_INFO_SCALE) |
+		BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+		BIT(IIO_CHAN_INFO_HYSTERESIS),
+		.scan_index = CHANNEL_SCAN_INDEX_PRESSURE,
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(CHANNEL_SCAN_INDEX_TIMESTAMP)
+
+};
+
+/* Adjust channel real bits based on report descriptor */
+static void press_adjust_channel_bit_mask(struct iio_chan_spec *channels,
+					int channel, int size)
+{
+	channels[channel].scan_type.sign = 's';
+	/* Real storage bits will change based on the report desc. */
+	channels[channel].scan_type.realbits = size * 8;
+	/* Maximum size of a sample to capture is u32 */
+	channels[channel].scan_type.storagebits = sizeof(u32) * 8;
+}
+
+/* Channel read_raw handler */
+static int press_read_raw(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      int *val, int *val2,
+			      long mask)
+{
+	struct press_state *press_state = iio_priv(indio_dev);
+	int report_id = -1;
+	u32 address;
+	int ret_type;
+	s32 min;
+
+	*val = 0;
+	*val2 = 0;
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		switch (chan->scan_index) {
+		case  CHANNEL_SCAN_INDEX_PRESSURE:
+			report_id = press_state->press_attr.report_id;
+			min = press_state->press_attr.logical_minimum;
+			address = HID_USAGE_SENSOR_ATMOSPHERIC_PRESSURE;
+			break;
+		default:
+			report_id = -1;
+			break;
+		}
+		if (report_id >= 0) {
+			hid_sensor_power_state(&press_state->common_attributes,
+						true);
+			*val = sensor_hub_input_attr_get_raw_value(
+				press_state->common_attributes.hsdev,
+				HID_USAGE_SENSOR_PRESSURE, address,
+				report_id,
+				SENSOR_HUB_SYNC,
+				min < 0);
+			hid_sensor_power_state(&press_state->common_attributes,
+						false);
+		} else {
+			*val = 0;
+			return -EINVAL;
+		}
+		ret_type = IIO_VAL_INT;
+		break;
+	case IIO_CHAN_INFO_SCALE:
+		*val = press_state->scale_pre_decml;
+		*val2 = press_state->scale_post_decml;
+		ret_type = press_state->scale_precision;
+		break;
+	case IIO_CHAN_INFO_OFFSET:
+		*val = press_state->value_offset;
+		ret_type = IIO_VAL_INT;
+		break;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		ret_type = hid_sensor_read_samp_freq_value(
+				&press_state->common_attributes, val, val2);
+		break;
+	case IIO_CHAN_INFO_HYSTERESIS:
+		ret_type = hid_sensor_read_raw_hyst_value(
+				&press_state->common_attributes, val, val2);
+		break;
+	default:
+		ret_type = -EINVAL;
+		break;
+	}
+
+	return ret_type;
+}
+
+/* Channel write_raw handler */
+static int press_write_raw(struct iio_dev *indio_dev,
+			       struct iio_chan_spec const *chan,
+			       int val,
+			       int val2,
+			       long mask)
+{
+	struct press_state *press_state = iio_priv(indio_dev);
+	int ret = 0;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		ret = hid_sensor_write_samp_freq_value(
+				&press_state->common_attributes, val, val2);
+		break;
+	case IIO_CHAN_INFO_HYSTERESIS:
+		ret = hid_sensor_write_raw_hyst_value(
+				&press_state->common_attributes, val, val2);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct iio_info press_info = {
+	.read_raw = &press_read_raw,
+	.write_raw = &press_write_raw,
+};
+
+/* Callback handler to send event after all samples are received and captured */
+static int press_proc_event(struct hid_sensor_hub_device *hsdev,
+				unsigned usage_id,
+				void *priv)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(priv);
+	struct press_state *press_state = iio_priv(indio_dev);
+
+	dev_dbg(&indio_dev->dev, "press_proc_event\n");
+	if (atomic_read(&press_state->common_attributes.data_ready)) {
+		if (!press_state->timestamp)
+			press_state->timestamp = iio_get_time_ns(indio_dev);
+
+		iio_push_to_buffers_with_timestamp(
+			indio_dev, &press_state->scan, press_state->timestamp);
+	}
+
+	return 0;
+}
+
+/* Capture samples in local storage */
+static int press_capture_sample(struct hid_sensor_hub_device *hsdev,
+				unsigned usage_id,
+				size_t raw_len, char *raw_data,
+				void *priv)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(priv);
+	struct press_state *press_state = iio_priv(indio_dev);
+	int ret = -EINVAL;
+
+	switch (usage_id) {
+	case HID_USAGE_SENSOR_ATMOSPHERIC_PRESSURE:
+		press_state->scan.press_data = *(u32 *)raw_data;
+		ret = 0;
+		break;
+	case HID_USAGE_SENSOR_TIME_TIMESTAMP:
+		press_state->timestamp = hid_sensor_convert_timestamp(
+			&press_state->common_attributes, *(s64 *)raw_data);
+		break;
+	default:
+		break;
+	}
+
+	return ret;
+}
+
+/* Parse report which is specific to an usage id*/
+static int press_parse_report(struct platform_device *pdev,
+				struct hid_sensor_hub_device *hsdev,
+				struct iio_chan_spec *channels,
+				unsigned usage_id,
+				struct press_state *st)
+{
+	int ret;
+
+	ret = sensor_hub_input_get_attribute_info(hsdev, HID_INPUT_REPORT,
+			usage_id,
+			HID_USAGE_SENSOR_ATMOSPHERIC_PRESSURE,
+			&st->press_attr);
+	if (ret < 0)
+		return ret;
+	press_adjust_channel_bit_mask(channels, CHANNEL_SCAN_INDEX_PRESSURE,
+					st->press_attr.size);
+
+	dev_dbg(&pdev->dev, "press %x:%x\n", st->press_attr.index,
+			st->press_attr.report_id);
+
+	st->scale_precision = hid_sensor_format_scale(
+				HID_USAGE_SENSOR_PRESSURE,
+				&st->press_attr,
+				&st->scale_pre_decml, &st->scale_post_decml);
+
+	return ret;
+}
+
+/* Function to initialize the processing for usage id */
+static int hid_press_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	static const char *name = "press";
+	struct iio_dev *indio_dev;
+	struct press_state *press_state;
+	struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data;
+
+	indio_dev = devm_iio_device_alloc(&pdev->dev,
+				sizeof(struct press_state));
+	if (!indio_dev)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, indio_dev);
+
+	press_state = iio_priv(indio_dev);
+	press_state->common_attributes.hsdev = hsdev;
+	press_state->common_attributes.pdev = pdev;
+
+	ret = hid_sensor_parse_common_attributes(hsdev,
+					HID_USAGE_SENSOR_PRESSURE,
+					&press_state->common_attributes,
+					press_sensitivity_addresses,
+					ARRAY_SIZE(press_sensitivity_addresses));
+	if (ret) {
+		dev_err(&pdev->dev, "failed to setup common attributes\n");
+		return ret;
+	}
+
+	indio_dev->channels = devm_kmemdup(&pdev->dev, press_channels,
+					   sizeof(press_channels), GFP_KERNEL);
+	if (!indio_dev->channels) {
+		dev_err(&pdev->dev, "failed to duplicate channels\n");
+		return -ENOMEM;
+	}
+
+	ret = press_parse_report(pdev, hsdev,
+				 (struct iio_chan_spec *)indio_dev->channels,
+				 HID_USAGE_SENSOR_PRESSURE, press_state);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to setup attributes\n");
+		return ret;
+	}
+
+	indio_dev->num_channels =
+				ARRAY_SIZE(press_channels);
+	indio_dev->info = &press_info;
+	indio_dev->name = name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	atomic_set(&press_state->common_attributes.data_ready, 0);
+
+	ret = hid_sensor_setup_trigger(indio_dev, name,
+				&press_state->common_attributes);
+	if (ret) {
+		dev_err(&pdev->dev, "trigger setup failed\n");
+		return ret;
+	}
+
+	ret = iio_device_register(indio_dev);
+	if (ret) {
+		dev_err(&pdev->dev, "device register failed\n");
+		goto error_remove_trigger;
+	}
+
+	press_state->callbacks.send_event = press_proc_event;
+	press_state->callbacks.capture_sample = press_capture_sample;
+	press_state->callbacks.pdev = pdev;
+	ret = sensor_hub_register_callback(hsdev, HID_USAGE_SENSOR_PRESSURE,
+					&press_state->callbacks);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "callback reg failed\n");
+		goto error_iio_unreg;
+	}
+
+	return ret;
+
+error_iio_unreg:
+	iio_device_unregister(indio_dev);
+error_remove_trigger:
+	hid_sensor_remove_trigger(indio_dev, &press_state->common_attributes);
+	return ret;
+}
+
+/* Function to deinitialize the processing for usage id */
+static int hid_press_remove(struct platform_device *pdev)
+{
+	struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data;
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct press_state *press_state = iio_priv(indio_dev);
+
+	sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_PRESSURE);
+	iio_device_unregister(indio_dev);
+	hid_sensor_remove_trigger(indio_dev, &press_state->common_attributes);
+
+	return 0;
+}
+
+static const struct platform_device_id hid_press_ids[] = {
+	{
+		/* Format: HID-SENSOR-usage_id_in_hex_lowercase */
+		.name = "HID-SENSOR-200031",
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, hid_press_ids);
+
+static struct platform_driver hid_press_platform_driver = {
+	.id_table = hid_press_ids,
+	.driver = {
+		.name	= KBUILD_MODNAME,
+		.pm	= &hid_sensor_pm_ops,
+	},
+	.probe		= hid_press_probe,
+	.remove		= hid_press_remove,
+};
+module_platform_driver(hid_press_platform_driver);
+
+MODULE_DESCRIPTION("HID Sensor Pressure");
+MODULE_AUTHOR("Archana Patni <archana.patni@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_HID);
diff --git a/drivers/iio/pressure/hp03.c b/drivers/iio/pressure/hp03.c
new file mode 100644
index 000000000..9538118c9
--- /dev/null
+++ b/drivers/iio/pressure/hp03.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2016 Marek Vasut <marex@denx.de>
+ *
+ * Driver for Hope RF HP03 digital temperature and pressure sensor.
+ */
+
+#define pr_fmt(fmt) "hp03: " fmt
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+/*
+ * The HP03 sensor occupies two fixed I2C addresses:
+ *  0x50 ... read-only EEPROM with calibration data
+ *  0x77 ... read-write ADC for pressure and temperature
+ */
+#define HP03_EEPROM_ADDR		0x50
+#define HP03_ADC_ADDR			0x77
+
+#define HP03_EEPROM_CX_OFFSET		0x10
+#define HP03_EEPROM_AB_OFFSET		0x1e
+#define HP03_EEPROM_CD_OFFSET		0x20
+
+#define HP03_ADC_WRITE_REG		0xff
+#define HP03_ADC_READ_REG		0xfd
+#define HP03_ADC_READ_PRESSURE		0xf0	/* D1 in datasheet */
+#define HP03_ADC_READ_TEMP		0xe8	/* D2 in datasheet */
+
+struct hp03_priv {
+	struct i2c_client	*client;
+	struct mutex		lock;
+	struct gpio_desc	*xclr_gpio;
+
+	struct i2c_client	*eeprom_client;
+	struct regmap		*eeprom_regmap;
+
+	s32			pressure;	/* kPa */
+	s32			temp;		/* Deg. C */
+};
+
+static const struct iio_chan_spec hp03_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+	},
+};
+
+static bool hp03_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	return false;
+}
+
+static bool hp03_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	return false;
+}
+
+static const struct regmap_config hp03_regmap_config = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+
+	.max_register	= HP03_EEPROM_CD_OFFSET + 1,
+	.cache_type	= REGCACHE_RBTREE,
+
+	.writeable_reg	= hp03_is_writeable_reg,
+	.volatile_reg	= hp03_is_volatile_reg,
+};
+
+static int hp03_get_temp_pressure(struct hp03_priv *priv, const u8 reg)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte_data(priv->client, HP03_ADC_WRITE_REG, reg);
+	if (ret < 0)
+		return ret;
+
+	msleep(50);	/* Wait for conversion to finish */
+
+	return i2c_smbus_read_word_data(priv->client, HP03_ADC_READ_REG);
+}
+
+static int hp03_update_temp_pressure(struct hp03_priv *priv)
+{
+	struct device *dev = &priv->client->dev;
+	u8 coefs[18];
+	u16 cx_val[7];
+	int ab_val, d1_val, d2_val, diff_val, dut, off, sens, x;
+	int i, ret;
+
+	/* Sample coefficients from EEPROM */
+	ret = regmap_bulk_read(priv->eeprom_regmap, HP03_EEPROM_CX_OFFSET,
+			       coefs, sizeof(coefs));
+	if (ret < 0) {
+		dev_err(dev, "Failed to read EEPROM (reg=%02x)\n",
+			HP03_EEPROM_CX_OFFSET);
+		return ret;
+	}
+
+	/* Sample Temperature and Pressure */
+	gpiod_set_value_cansleep(priv->xclr_gpio, 1);
+
+	ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_PRESSURE);
+	if (ret < 0) {
+		dev_err(dev, "Failed to read pressure\n");
+		goto err_adc;
+	}
+	d1_val = ret;
+
+	ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_TEMP);
+	if (ret < 0) {
+		dev_err(dev, "Failed to read temperature\n");
+		goto err_adc;
+	}
+	d2_val = ret;
+
+	gpiod_set_value_cansleep(priv->xclr_gpio, 0);
+
+	/* The Cx coefficients and Temp/Pressure values are MSB first. */
+	for (i = 0; i < 7; i++)
+		cx_val[i] = (coefs[2 * i] << 8) | (coefs[(2 * i) + 1] << 0);
+	d1_val = ((d1_val >> 8) & 0xff) | ((d1_val & 0xff) << 8);
+	d2_val = ((d2_val >> 8) & 0xff) | ((d2_val & 0xff) << 8);
+
+	/* Coefficient voodoo from the HP03 datasheet. */
+	if (d2_val >= cx_val[4])
+		ab_val = coefs[14];	/* A-value */
+	else
+		ab_val = coefs[15];	/* B-value */
+
+	diff_val = d2_val - cx_val[4];
+	dut = (ab_val * (diff_val >> 7) * (diff_val >> 7)) >> coefs[16];
+	dut = diff_val - dut;
+
+	off = (cx_val[1] + (((cx_val[3] - 1024) * dut) >> 14)) * 4;
+	sens = cx_val[0] + ((cx_val[2] * dut) >> 10);
+	x = ((sens * (d1_val - 7168)) >> 14) - off;
+
+	priv->pressure = ((x * 100) >> 5) + (cx_val[6] * 10);
+	priv->temp = 250 + ((dut * cx_val[5]) >> 16) - (dut >> coefs[17]);
+
+	return 0;
+
+err_adc:
+	gpiod_set_value_cansleep(priv->xclr_gpio, 0);
+	return ret;
+}
+
+static int hp03_read_raw(struct iio_dev *indio_dev,
+			 struct iio_chan_spec const *chan,
+			 int *val, int *val2, long mask)
+{
+	struct hp03_priv *priv = iio_priv(indio_dev);
+	int ret;
+
+	mutex_lock(&priv->lock);
+	ret = hp03_update_temp_pressure(priv);
+	mutex_unlock(&priv->lock);
+
+	if (ret)
+		return ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			*val = priv->pressure;
+			return IIO_VAL_INT;
+		case IIO_TEMP:
+			*val = priv->temp;
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+		break;
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			*val = 0;
+			*val2 = 1000;
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+			*val = 10;
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info hp03_info = {
+	.read_raw	= &hp03_read_raw,
+};
+
+static int hp03_probe(struct i2c_client *client,
+		      const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct iio_dev *indio_dev;
+	struct hp03_priv *priv;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	priv = iio_priv(indio_dev);
+	priv->client = client;
+	mutex_init(&priv->lock);
+
+	indio_dev->name = id->name;
+	indio_dev->channels = hp03_channels;
+	indio_dev->num_channels = ARRAY_SIZE(hp03_channels);
+	indio_dev->info = &hp03_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	priv->xclr_gpio = devm_gpiod_get_index(dev, "xclr", 0, GPIOD_OUT_HIGH);
+	if (IS_ERR(priv->xclr_gpio)) {
+		dev_err(dev, "Failed to claim XCLR GPIO\n");
+		ret = PTR_ERR(priv->xclr_gpio);
+		return ret;
+	}
+
+	/*
+	 * Allocate another device for the on-sensor EEPROM,
+	 * which has it's dedicated I2C address and contains
+	 * the calibration constants for the sensor.
+	 */
+	priv->eeprom_client = devm_i2c_new_dummy_device(dev, client->adapter,
+							HP03_EEPROM_ADDR);
+	if (IS_ERR(priv->eeprom_client)) {
+		dev_err(dev, "New EEPROM I2C device failed\n");
+		return PTR_ERR(priv->eeprom_client);
+	}
+
+	priv->eeprom_regmap = devm_regmap_init_i2c(priv->eeprom_client,
+						   &hp03_regmap_config);
+	if (IS_ERR(priv->eeprom_regmap)) {
+		dev_err(dev, "Failed to allocate EEPROM regmap\n");
+		return PTR_ERR(priv->eeprom_regmap);
+	}
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret) {
+		dev_err(dev, "Failed to register IIO device\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id hp03_id[] = {
+	{ "hp03", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, hp03_id);
+
+static const struct of_device_id hp03_of_match[] = {
+	{ .compatible = "hoperf,hp03" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hp03_of_match);
+
+static struct i2c_driver hp03_driver = {
+	.driver = {
+		.name	= "hp03",
+		.of_match_table = hp03_of_match,
+	},
+	.probe		= hp03_probe,
+	.id_table	= hp03_id,
+};
+module_i2c_driver(hp03_driver);
+
+MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
+MODULE_DESCRIPTION("Driver for Hope RF HP03 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/hp206c.c b/drivers/iio/pressure/hp206c.c
new file mode 100644
index 000000000..986b7a597
--- /dev/null
+++ b/drivers/iio/pressure/hp206c.c
@@ -0,0 +1,424 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * hp206c.c - HOPERF HP206C precision barometer and altimeter sensor
+ *
+ * Copyright (c) 2016, Intel Corporation.
+ *
+ * (7-bit I2C slave address 0x76)
+ *
+ * Datasheet:
+ *  http://www.hoperf.com/upload/sensor/HP206C_DataSheet_EN_V2.0.pdf
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/delay.h>
+#include <linux/util_macros.h>
+#include <linux/acpi.h>
+
+#include <asm/unaligned.h>
+
+/* I2C commands: */
+#define HP206C_CMD_SOFT_RST	0x06
+
+#define HP206C_CMD_ADC_CVT	0x40
+
+#define HP206C_CMD_ADC_CVT_OSR_4096	0x00
+#define HP206C_CMD_ADC_CVT_OSR_2048	0x04
+#define HP206C_CMD_ADC_CVT_OSR_1024	0x08
+#define HP206C_CMD_ADC_CVT_OSR_512	0x0c
+#define HP206C_CMD_ADC_CVT_OSR_256	0x10
+#define HP206C_CMD_ADC_CVT_OSR_128	0x14
+
+#define HP206C_CMD_ADC_CVT_CHNL_PT	0x00
+#define HP206C_CMD_ADC_CVT_CHNL_T	0x02
+
+#define HP206C_CMD_READ_P	0x30
+#define HP206C_CMD_READ_T	0x32
+
+#define HP206C_CMD_READ_REG	0x80
+#define HP206C_CMD_WRITE_REG	0xc0
+
+#define HP206C_REG_INT_EN	0x0b
+#define HP206C_REG_INT_CFG	0x0c
+
+#define HP206C_REG_INT_SRC	0x0d
+#define HP206C_FLAG_DEV_RDY	0x40
+
+#define HP206C_REG_PARA		0x0f
+#define HP206C_FLAG_CMPS_EN	0x80
+
+/* Maximum spin for DEV_RDY */
+#define HP206C_MAX_DEV_RDY_WAIT_COUNT 20
+#define HP206C_DEV_RDY_WAIT_US    20000
+
+struct hp206c_data {
+	struct mutex mutex;
+	struct i2c_client *client;
+	int temp_osr_index;
+	int pres_osr_index;
+};
+
+struct hp206c_osr_setting {
+	u8 osr_mask;
+	unsigned int temp_conv_time_us;
+	unsigned int pres_conv_time_us;
+};
+
+/* Data from Table 5 in datasheet. */
+static const struct hp206c_osr_setting hp206c_osr_settings[] = {
+	{ HP206C_CMD_ADC_CVT_OSR_4096,	65600,	131100	},
+	{ HP206C_CMD_ADC_CVT_OSR_2048,	32800,	65600	},
+	{ HP206C_CMD_ADC_CVT_OSR_1024,	16400,	32800	},
+	{ HP206C_CMD_ADC_CVT_OSR_512,	8200,	16400	},
+	{ HP206C_CMD_ADC_CVT_OSR_256,	4100,	8200	},
+	{ HP206C_CMD_ADC_CVT_OSR_128,	2100,	4100	},
+};
+static const int hp206c_osr_rates[] = { 4096, 2048, 1024, 512, 256, 128 };
+static const char hp206c_osr_rates_str[] = "4096 2048 1024 512 256 128";
+
+static inline int hp206c_read_reg(struct i2c_client *client, u8 reg)
+{
+	return i2c_smbus_read_byte_data(client, HP206C_CMD_READ_REG | reg);
+}
+
+static inline int hp206c_write_reg(struct i2c_client *client, u8 reg, u8 val)
+{
+	return i2c_smbus_write_byte_data(client,
+			HP206C_CMD_WRITE_REG | reg, val);
+}
+
+static int hp206c_read_20bit(struct i2c_client *client, u8 cmd)
+{
+	int ret;
+	u8 values[3];
+
+	ret = i2c_smbus_read_i2c_block_data(client, cmd, sizeof(values), values);
+	if (ret < 0)
+		return ret;
+	if (ret != sizeof(values))
+		return -EIO;
+	return get_unaligned_be24(&values[0]) & GENMASK(19, 0);
+}
+
+/* Spin for max 160ms until DEV_RDY is 1, or return error. */
+static int hp206c_wait_dev_rdy(struct iio_dev *indio_dev)
+{
+	int ret;
+	int count = 0;
+	struct hp206c_data *data = iio_priv(indio_dev);
+	struct i2c_client *client = data->client;
+
+	while (++count <= HP206C_MAX_DEV_RDY_WAIT_COUNT) {
+		ret = hp206c_read_reg(client, HP206C_REG_INT_SRC);
+		if (ret < 0) {
+			dev_err(&indio_dev->dev, "Failed READ_REG INT_SRC: %d\n", ret);
+			return ret;
+		}
+		if (ret & HP206C_FLAG_DEV_RDY)
+			return 0;
+		usleep_range(HP206C_DEV_RDY_WAIT_US, HP206C_DEV_RDY_WAIT_US * 3 / 2);
+	}
+	return -ETIMEDOUT;
+}
+
+static int hp206c_set_compensation(struct i2c_client *client, bool enabled)
+{
+	int val;
+
+	val = hp206c_read_reg(client, HP206C_REG_PARA);
+	if (val < 0)
+		return val;
+	if (enabled)
+		val |= HP206C_FLAG_CMPS_EN;
+	else
+		val &= ~HP206C_FLAG_CMPS_EN;
+
+	return hp206c_write_reg(client, HP206C_REG_PARA, val);
+}
+
+/* Do a soft reset */
+static int hp206c_soft_reset(struct iio_dev *indio_dev)
+{
+	int ret;
+	struct hp206c_data *data = iio_priv(indio_dev);
+	struct i2c_client *client = data->client;
+
+	ret = i2c_smbus_write_byte(client, HP206C_CMD_SOFT_RST);
+	if (ret) {
+		dev_err(&client->dev, "Failed to reset device: %d\n", ret);
+		return ret;
+	}
+
+	usleep_range(400, 600);
+
+	ret = hp206c_wait_dev_rdy(indio_dev);
+	if (ret) {
+		dev_err(&client->dev, "Device not ready after soft reset: %d\n", ret);
+		return ret;
+	}
+
+	ret = hp206c_set_compensation(client, true);
+	if (ret)
+		dev_err(&client->dev, "Failed to enable compensation: %d\n", ret);
+	return ret;
+}
+
+static int hp206c_conv_and_read(struct iio_dev *indio_dev,
+				u8 conv_cmd, u8 read_cmd,
+				unsigned int sleep_us)
+{
+	int ret;
+	struct hp206c_data *data = iio_priv(indio_dev);
+	struct i2c_client *client = data->client;
+
+	ret = hp206c_wait_dev_rdy(indio_dev);
+	if (ret < 0) {
+		dev_err(&indio_dev->dev, "Device not ready: %d\n", ret);
+		return ret;
+	}
+
+	ret = i2c_smbus_write_byte(client, conv_cmd);
+	if (ret < 0) {
+		dev_err(&indio_dev->dev, "Failed convert: %d\n", ret);
+		return ret;
+	}
+
+	usleep_range(sleep_us, sleep_us * 3 / 2);
+
+	ret = hp206c_wait_dev_rdy(indio_dev);
+	if (ret < 0) {
+		dev_err(&indio_dev->dev, "Device not ready: %d\n", ret);
+		return ret;
+	}
+
+	ret = hp206c_read_20bit(client, read_cmd);
+	if (ret < 0)
+		dev_err(&indio_dev->dev, "Failed read: %d\n", ret);
+
+	return ret;
+}
+
+static int hp206c_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan, int *val,
+			   int *val2, long mask)
+{
+	int ret;
+	struct hp206c_data *data = iio_priv(indio_dev);
+	const struct hp206c_osr_setting *osr_setting;
+	u8 conv_cmd;
+
+	mutex_lock(&data->mutex);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		switch (chan->type) {
+		case IIO_TEMP:
+			*val = hp206c_osr_rates[data->temp_osr_index];
+			ret = IIO_VAL_INT;
+			break;
+
+		case IIO_PRESSURE:
+			*val = hp206c_osr_rates[data->pres_osr_index];
+			ret = IIO_VAL_INT;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+		break;
+
+	case IIO_CHAN_INFO_RAW:
+		switch (chan->type) {
+		case IIO_TEMP:
+			osr_setting = &hp206c_osr_settings[data->temp_osr_index];
+			conv_cmd = HP206C_CMD_ADC_CVT |
+					osr_setting->osr_mask |
+					HP206C_CMD_ADC_CVT_CHNL_T;
+			ret = hp206c_conv_and_read(indio_dev,
+					conv_cmd,
+					HP206C_CMD_READ_T,
+					osr_setting->temp_conv_time_us);
+			if (ret >= 0) {
+				/* 20 significant bits are provided.
+				 * Extend sign over the rest.
+				 */
+				*val = sign_extend32(ret, 19);
+				ret = IIO_VAL_INT;
+			}
+			break;
+
+		case IIO_PRESSURE:
+			osr_setting = &hp206c_osr_settings[data->pres_osr_index];
+			conv_cmd = HP206C_CMD_ADC_CVT |
+					osr_setting->osr_mask |
+					HP206C_CMD_ADC_CVT_CHNL_PT;
+			ret = hp206c_conv_and_read(indio_dev,
+					conv_cmd,
+					HP206C_CMD_READ_P,
+					osr_setting->pres_conv_time_us);
+			if (ret >= 0) {
+				*val = ret;
+				ret = IIO_VAL_INT;
+			}
+			break;
+		default:
+			ret = -EINVAL;
+		}
+		break;
+
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_TEMP:
+			*val = 0;
+			*val2 = 10000;
+			ret = IIO_VAL_INT_PLUS_MICRO;
+			break;
+
+		case IIO_PRESSURE:
+			*val = 0;
+			*val2 = 1000;
+			ret = IIO_VAL_INT_PLUS_MICRO;
+			break;
+		default:
+			ret = -EINVAL;
+		}
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&data->mutex);
+	return ret;
+}
+
+static int hp206c_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	int ret = 0;
+	struct hp206c_data *data = iio_priv(indio_dev);
+
+	if (mask != IIO_CHAN_INFO_OVERSAMPLING_RATIO)
+		return -EINVAL;
+	mutex_lock(&data->mutex);
+	switch (chan->type) {
+	case IIO_TEMP:
+		data->temp_osr_index = find_closest_descending(val,
+			hp206c_osr_rates, ARRAY_SIZE(hp206c_osr_rates));
+		break;
+	case IIO_PRESSURE:
+		data->pres_osr_index = find_closest_descending(val,
+			hp206c_osr_rates, ARRAY_SIZE(hp206c_osr_rates));
+		break;
+	default:
+		ret = -EINVAL;
+	}
+	mutex_unlock(&data->mutex);
+	return ret;
+}
+
+static const struct iio_chan_spec hp206c_channels[] = {
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	},
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE) |
+				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	}
+};
+
+static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(hp206c_osr_rates_str);
+
+static struct attribute *hp206c_attributes[] = {
+	&iio_const_attr_sampling_frequency_available.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group hp206c_attribute_group = {
+	.attrs = hp206c_attributes,
+};
+
+static const struct iio_info hp206c_info = {
+	.attrs = &hp206c_attribute_group,
+	.read_raw = hp206c_read_raw,
+	.write_raw = hp206c_write_raw,
+};
+
+static int hp206c_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct iio_dev *indio_dev;
+	struct hp206c_data *data;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE |
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+		dev_err(&client->dev, "Adapter does not support "
+				"all required i2c functionality\n");
+		return -ENODEV;
+	}
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	data->client = client;
+	mutex_init(&data->mutex);
+
+	indio_dev->info = &hp206c_info;
+	indio_dev->name = id->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = hp206c_channels;
+	indio_dev->num_channels = ARRAY_SIZE(hp206c_channels);
+
+	i2c_set_clientdata(client, indio_dev);
+
+	/* Do a soft reset on probe */
+	ret = hp206c_soft_reset(indio_dev);
+	if (ret) {
+		dev_err(&client->dev, "Failed to reset on startup: %d\n", ret);
+		return -ENODEV;
+	}
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static const struct i2c_device_id hp206c_id[] = {
+	{"hp206c"},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, hp206c_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id hp206c_acpi_match[] = {
+	{"HOP206C", 0},
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, hp206c_acpi_match);
+#endif
+
+static struct i2c_driver hp206c_driver = {
+	.probe = hp206c_probe,
+	.id_table = hp206c_id,
+	.driver = {
+		.name = "hp206c",
+		.acpi_match_table = ACPI_PTR(hp206c_acpi_match),
+	},
+};
+
+module_i2c_driver(hp206c_driver);
+
+MODULE_DESCRIPTION("HOPERF HP206C precision barometer and altimeter sensor");
+MODULE_AUTHOR("Leonard Crestez <leonard.crestez@intel.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/icp10100.c b/drivers/iio/pressure/icp10100.c
new file mode 100644
index 000000000..b62f28585
--- /dev/null
+++ b/drivers/iio/pressure/icp10100.c
@@ -0,0 +1,659 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 InvenSense, Inc.
+ *
+ * Driver for InvenSense ICP-1010xx barometric pressure and temperature sensor.
+ *
+ * Datasheet:
+ * http://www.invensense.com/wp-content/uploads/2018/01/DS-000186-ICP-101xx-v1.2.pdf
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/i2c.h>
+#include <linux/pm_runtime.h>
+#include <linux/crc8.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/regulator/consumer.h>
+#include <linux/iio/iio.h>
+
+#define ICP10100_ID_REG_GET(_reg)	((_reg) & 0x003F)
+#define ICP10100_ID_REG			0x08
+#define ICP10100_RESPONSE_WORD_LENGTH	3
+#define ICP10100_CRC8_WORD_LENGTH	2
+#define ICP10100_CRC8_POLYNOMIAL	0x31
+#define ICP10100_CRC8_INIT		0xFF
+
+enum icp10100_mode {
+	ICP10100_MODE_LP,	/* Low power mode: 1x sampling */
+	ICP10100_MODE_N,	/* Normal mode: 2x sampling */
+	ICP10100_MODE_LN,	/* Low noise mode: 4x sampling */
+	ICP10100_MODE_ULN,	/* Ultra low noise mode: 8x sampling */
+	ICP10100_MODE_NB,
+};
+
+struct icp10100_state {
+	struct mutex lock;
+	struct i2c_client *client;
+	struct regulator *vdd;
+	enum icp10100_mode mode;
+	int16_t cal[4];
+};
+
+struct icp10100_command {
+	__be16 cmd;
+	unsigned long wait_us;
+	unsigned long wait_max_us;
+	size_t response_word_nb;
+};
+
+static const struct icp10100_command icp10100_cmd_soft_reset = {
+	.cmd = cpu_to_be16(0x805D),
+	.wait_us = 170,
+	.wait_max_us = 200,
+	.response_word_nb = 0,
+};
+
+static const struct icp10100_command icp10100_cmd_read_id = {
+	.cmd = cpu_to_be16(0xEFC8),
+	.wait_us = 0,
+	.response_word_nb = 1,
+};
+
+static const struct icp10100_command icp10100_cmd_read_otp = {
+	.cmd = cpu_to_be16(0xC7F7),
+	.wait_us = 0,
+	.response_word_nb = 1,
+};
+
+static const struct icp10100_command icp10100_cmd_measure[] = {
+	[ICP10100_MODE_LP] = {
+		.cmd = cpu_to_be16(0x401A),
+		.wait_us = 1800,
+		.wait_max_us = 2000,
+		.response_word_nb = 3,
+	},
+	[ICP10100_MODE_N] = {
+		.cmd = cpu_to_be16(0x48A3),
+		.wait_us = 6300,
+		.wait_max_us = 6500,
+		.response_word_nb = 3,
+	},
+	[ICP10100_MODE_LN] = {
+		.cmd = cpu_to_be16(0x5059),
+		.wait_us = 23800,
+		.wait_max_us = 24000,
+		.response_word_nb = 3,
+	},
+	[ICP10100_MODE_ULN] = {
+		.cmd = cpu_to_be16(0x58E0),
+		.wait_us = 94500,
+		.wait_max_us = 94700,
+		.response_word_nb = 3,
+	},
+};
+
+static const uint8_t icp10100_switch_mode_otp[] =
+	{0xC5, 0x95, 0x00, 0x66, 0x9c};
+
+DECLARE_CRC8_TABLE(icp10100_crc8_table);
+
+static inline int icp10100_i2c_xfer(struct i2c_adapter *adap,
+				    struct i2c_msg *msgs, int num)
+{
+	int ret;
+
+	ret = i2c_transfer(adap, msgs, num);
+	if (ret < 0)
+		return ret;
+
+	if (ret != num)
+		return -EIO;
+
+	return 0;
+}
+
+static int icp10100_send_cmd(struct icp10100_state *st,
+			     const struct icp10100_command *cmd,
+			     __be16 *buf, size_t buf_len)
+{
+	size_t size = cmd->response_word_nb * ICP10100_RESPONSE_WORD_LENGTH;
+	uint8_t data[16];
+	uint8_t *ptr;
+	uint8_t *buf_ptr = (uint8_t *)buf;
+	struct i2c_msg msgs[2] = {
+		{
+			.addr = st->client->addr,
+			.flags = 0,
+			.len = 2,
+			.buf = (uint8_t *)&cmd->cmd,
+		}, {
+			.addr = st->client->addr,
+			.flags = I2C_M_RD,
+			.len = size,
+			.buf = data,
+		},
+	};
+	uint8_t crc;
+	unsigned int i;
+	int ret;
+
+	if (size > sizeof(data))
+		return -EINVAL;
+
+	if (cmd->response_word_nb > 0 &&
+			(buf == NULL || buf_len < (cmd->response_word_nb * 2)))
+		return -EINVAL;
+
+	dev_dbg(&st->client->dev, "sending cmd %#x\n", be16_to_cpu(cmd->cmd));
+
+	if (cmd->response_word_nb > 0 && cmd->wait_us == 0) {
+		/* direct command-response without waiting */
+		ret = icp10100_i2c_xfer(st->client->adapter, msgs,
+					ARRAY_SIZE(msgs));
+		if (ret)
+			return ret;
+	} else {
+		/* transfer command write */
+		ret = icp10100_i2c_xfer(st->client->adapter, &msgs[0], 1);
+		if (ret)
+			return ret;
+		if (cmd->wait_us > 0)
+			usleep_range(cmd->wait_us, cmd->wait_max_us);
+		/* transfer response read if needed */
+		if (cmd->response_word_nb > 0) {
+			ret = icp10100_i2c_xfer(st->client->adapter, &msgs[1], 1);
+			if (ret)
+				return ret;
+		} else {
+			return 0;
+		}
+	}
+
+	/* process read words with crc checking */
+	for (i = 0; i < cmd->response_word_nb; ++i) {
+		ptr = &data[i * ICP10100_RESPONSE_WORD_LENGTH];
+		crc = crc8(icp10100_crc8_table, ptr, ICP10100_CRC8_WORD_LENGTH,
+			   ICP10100_CRC8_INIT);
+		if (crc != ptr[ICP10100_CRC8_WORD_LENGTH]) {
+			dev_err(&st->client->dev, "crc error recv=%#x calc=%#x\n",
+				ptr[ICP10100_CRC8_WORD_LENGTH], crc);
+			return -EIO;
+		}
+		*buf_ptr++ = ptr[0];
+		*buf_ptr++ = ptr[1];
+	}
+
+	return 0;
+}
+
+static int icp10100_read_cal_otp(struct icp10100_state *st)
+{
+	__be16 val;
+	int i;
+	int ret;
+
+	/* switch into OTP read mode */
+	ret = i2c_master_send(st->client, icp10100_switch_mode_otp,
+			      ARRAY_SIZE(icp10100_switch_mode_otp));
+	if (ret < 0)
+		return ret;
+	if (ret != ARRAY_SIZE(icp10100_switch_mode_otp))
+		return -EIO;
+
+	/* read 4 calibration values */
+	for (i = 0; i < 4; ++i) {
+		ret = icp10100_send_cmd(st, &icp10100_cmd_read_otp,
+					&val, sizeof(val));
+		if (ret)
+			return ret;
+		st->cal[i] = be16_to_cpu(val);
+		dev_dbg(&st->client->dev, "cal[%d] = %d\n", i, st->cal[i]);
+	}
+
+	return 0;
+}
+
+static int icp10100_init_chip(struct icp10100_state *st)
+{
+	__be16 val;
+	uint16_t id;
+	int ret;
+
+	/* read and check id */
+	ret = icp10100_send_cmd(st, &icp10100_cmd_read_id, &val, sizeof(val));
+	if (ret)
+		return ret;
+	id = ICP10100_ID_REG_GET(be16_to_cpu(val));
+	if (id != ICP10100_ID_REG) {
+		dev_err(&st->client->dev, "invalid id %#x\n", id);
+		return -ENODEV;
+	}
+
+	/* read calibration data from OTP */
+	ret = icp10100_read_cal_otp(st);
+	if (ret)
+		return ret;
+
+	/* reset chip */
+	return icp10100_send_cmd(st, &icp10100_cmd_soft_reset, NULL, 0);
+}
+
+static int icp10100_get_measures(struct icp10100_state *st,
+				uint32_t *pressure, uint16_t *temperature)
+{
+	const struct icp10100_command *cmd;
+	__be16 measures[3];
+	int ret;
+
+	ret = pm_runtime_resume_and_get(&st->client->dev);
+	if (ret < 0)
+		return ret;
+
+	mutex_lock(&st->lock);
+	cmd = &icp10100_cmd_measure[st->mode];
+	ret = icp10100_send_cmd(st, cmd, measures, sizeof(measures));
+	mutex_unlock(&st->lock);
+	if (ret)
+		goto error_measure;
+
+	*pressure = (be16_to_cpu(measures[0]) << 8) |
+			(be16_to_cpu(measures[1]) >> 8);
+	*temperature = be16_to_cpu(measures[2]);
+
+	pm_runtime_mark_last_busy(&st->client->dev);
+error_measure:
+	pm_runtime_put_autosuspend(&st->client->dev);
+	return ret;
+}
+
+static uint32_t icp10100_get_pressure(struct icp10100_state *st,
+				      uint32_t raw_pressure, uint16_t raw_temp)
+{
+	static int32_t p_calib[] = {45000, 80000, 105000};
+	static int32_t lut_lower = 3670016;
+	static int32_t lut_upper = 12058624;
+	static int32_t inv_quadr_factor = 16777216;
+	static int32_t offset_factor = 2048;
+	int64_t val1, val2;
+	int32_t p_lut[3];
+	int32_t t, t_square;
+	int64_t a, b, c;
+	uint32_t pressure_mPa;
+
+	dev_dbg(&st->client->dev, "raw: pressure = %u, temp = %u\n",
+		raw_pressure, raw_temp);
+
+	/* compute p_lut values */
+	t = (int32_t)raw_temp - 32768;
+	t_square = t * t;
+	val1 = (int64_t)st->cal[0] * (int64_t)t_square;
+	p_lut[0] = lut_lower + (int32_t)div_s64(val1, inv_quadr_factor);
+	val1 = (int64_t)st->cal[1] * (int64_t)t_square;
+	p_lut[1] = offset_factor * st->cal[3] +
+			(int32_t)div_s64(val1, inv_quadr_factor);
+	val1 = (int64_t)st->cal[2] * (int64_t)t_square;
+	p_lut[2] = lut_upper + (int32_t)div_s64(val1, inv_quadr_factor);
+	dev_dbg(&st->client->dev, "p_lut = [%d, %d, %d]\n",
+		p_lut[0], p_lut[1], p_lut[2]);
+
+	/* compute a, b, c factors */
+	val1 = (int64_t)p_lut[0] * (int64_t)p_lut[1] *
+			(int64_t)(p_calib[0] - p_calib[1]) +
+		(int64_t)p_lut[1] * (int64_t)p_lut[2] *
+			(int64_t)(p_calib[1] - p_calib[2]) +
+		(int64_t)p_lut[2] * (int64_t)p_lut[0] *
+			(int64_t)(p_calib[2] - p_calib[0]);
+	val2 = (int64_t)p_lut[2] * (int64_t)(p_calib[0] - p_calib[1]) +
+		(int64_t)p_lut[0] * (int64_t)(p_calib[1] - p_calib[2]) +
+		(int64_t)p_lut[1] * (int64_t)(p_calib[2] - p_calib[0]);
+	c = div64_s64(val1, val2);
+	dev_dbg(&st->client->dev, "val1 = %lld, val2 = %lld, c = %lld\n",
+		val1, val2, c);
+	val1 = (int64_t)p_calib[0] * (int64_t)p_lut[0] -
+		(int64_t)p_calib[1] * (int64_t)p_lut[1] -
+		(int64_t)(p_calib[1] - p_calib[0]) * c;
+	val2 = (int64_t)p_lut[0] - (int64_t)p_lut[1];
+	a = div64_s64(val1, val2);
+	dev_dbg(&st->client->dev, "val1 = %lld, val2 = %lld, a = %lld\n",
+		val1, val2, a);
+	b = ((int64_t)p_calib[0] - a) * ((int64_t)p_lut[0] + c);
+	dev_dbg(&st->client->dev, "b = %lld\n", b);
+
+	/*
+	 * pressure_Pa = a + (b / (c + raw_pressure))
+	 * pressure_mPa = 1000 * pressure_Pa
+	 */
+	pressure_mPa = 1000LL * a + div64_s64(1000LL * b, c + raw_pressure);
+
+	return pressure_mPa;
+}
+
+static int icp10100_read_raw_measures(struct iio_dev *indio_dev,
+				      struct iio_chan_spec const *chan,
+				      int *val, int *val2)
+{
+	struct icp10100_state *st = iio_priv(indio_dev);
+	uint32_t raw_pressure;
+	uint16_t raw_temp;
+	uint32_t pressure_mPa;
+	int ret;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = icp10100_get_measures(st, &raw_pressure, &raw_temp);
+	if (ret)
+		goto error_release;
+
+	switch (chan->type) {
+	case IIO_PRESSURE:
+		pressure_mPa = icp10100_get_pressure(st, raw_pressure,
+						     raw_temp);
+		/* mPa to kPa */
+		*val = pressure_mPa / 1000000;
+		*val2 = pressure_mPa % 1000000;
+		ret = IIO_VAL_INT_PLUS_MICRO;
+		break;
+	case IIO_TEMP:
+		*val = raw_temp;
+		ret = IIO_VAL_INT;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+error_release:
+	iio_device_release_direct_mode(indio_dev);
+	return ret;
+}
+
+static int icp10100_read_raw(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     int *val, int *val2, long mask)
+{
+	struct icp10100_state *st = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+	case IIO_CHAN_INFO_PROCESSED:
+		return icp10100_read_raw_measures(indio_dev, chan, val, val2);
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_TEMP:
+			/* 1000 * 175°C / 65536 in m°C */
+			*val = 2;
+			*val2 = 670288;
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+		break;
+	case IIO_CHAN_INFO_OFFSET:
+		switch (chan->type) {
+		case IIO_TEMP:
+			/* 1000 * -45°C in m°C */
+			*val = -45000;
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+		break;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		mutex_lock(&st->lock);
+		*val = 1 << st->mode;
+		mutex_unlock(&st->lock);
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int icp10100_read_avail(struct iio_dev *indio_dev,
+			       struct iio_chan_spec const *chan,
+			       const int **vals, int *type, int *length,
+			       long mask)
+{
+	static int oversamplings[] = {1, 2, 4, 8};
+
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*vals = oversamplings;
+		*type = IIO_VAL_INT;
+		*length = ARRAY_SIZE(oversamplings);
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int icp10100_write_raw(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      int val, int val2, long mask)
+{
+	struct icp10100_state *st = iio_priv(indio_dev);
+	unsigned int mode;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		/* oversampling is always positive and a power of 2 */
+		if (val <= 0 || !is_power_of_2(val))
+			return -EINVAL;
+		mode = ilog2(val);
+		if (mode >= ICP10100_MODE_NB)
+			return -EINVAL;
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+		mutex_lock(&st->lock);
+		st->mode = mode;
+		mutex_unlock(&st->lock);
+		iio_device_release_direct_mode(indio_dev);
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int icp10100_write_raw_get_fmt(struct iio_dev *indio_dev,
+				      struct iio_chan_spec const *chan,
+				      long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info icp10100_info = {
+	.read_raw = icp10100_read_raw,
+	.read_avail = icp10100_read_avail,
+	.write_raw = icp10100_write_raw,
+	.write_raw_get_fmt = icp10100_write_raw_get_fmt,
+};
+
+static const struct iio_chan_spec icp10100_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+		.info_mask_shared_by_all =
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.info_mask_shared_by_all_available =
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	}, {
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OFFSET),
+		.info_mask_shared_by_all =
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.info_mask_shared_by_all_available =
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+	},
+};
+
+static int icp10100_enable_regulator(struct icp10100_state *st)
+{
+	int ret;
+
+	ret = regulator_enable(st->vdd);
+	if (ret)
+		return ret;
+	msleep(100);
+
+	return 0;
+}
+
+static void icp10100_disable_regulator_action(void *data)
+{
+	struct icp10100_state *st = data;
+	int ret;
+
+	ret = regulator_disable(st->vdd);
+	if (ret)
+		dev_err(&st->client->dev, "error %d disabling vdd\n", ret);
+}
+
+static void icp10100_pm_disable(void *data)
+{
+	struct device *dev = data;
+
+	pm_runtime_disable(dev);
+}
+
+static int icp10100_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct iio_dev *indio_dev;
+	struct icp10100_state *st;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "plain i2c transactions not supported\n");
+		return -ENODEV;
+	}
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, indio_dev);
+	indio_dev->name = client->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = icp10100_channels;
+	indio_dev->num_channels = ARRAY_SIZE(icp10100_channels);
+	indio_dev->info = &icp10100_info;
+
+	st = iio_priv(indio_dev);
+	mutex_init(&st->lock);
+	st->client = client;
+	st->mode = ICP10100_MODE_N;
+
+	st->vdd = devm_regulator_get(&client->dev, "vdd");
+	if (IS_ERR(st->vdd))
+		return PTR_ERR(st->vdd);
+
+	ret = icp10100_enable_regulator(st);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(&client->dev,
+				       icp10100_disable_regulator_action, st);
+	if (ret)
+		return ret;
+
+	/* has to be done before the first i2c communication */
+	crc8_populate_msb(icp10100_crc8_table, ICP10100_CRC8_POLYNOMIAL);
+
+	ret = icp10100_init_chip(st);
+	if (ret) {
+		dev_err(&client->dev, "init chip error %d\n", ret);
+		return ret;
+	}
+
+	/* enable runtime pm with autosuspend delay of 2s */
+	pm_runtime_get_noresume(&client->dev);
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_set_autosuspend_delay(&client->dev, 2000);
+	pm_runtime_use_autosuspend(&client->dev);
+	pm_runtime_put(&client->dev);
+	ret = devm_add_action_or_reset(&client->dev, icp10100_pm_disable,
+				       &client->dev);
+	if (ret)
+		return ret;
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static int icp10100_suspend(struct device *dev)
+{
+	struct icp10100_state *st = iio_priv(dev_get_drvdata(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+	ret = regulator_disable(st->vdd);
+	mutex_unlock(&st->lock);
+
+	return ret;
+}
+
+static int icp10100_resume(struct device *dev)
+{
+	struct icp10100_state *st = iio_priv(dev_get_drvdata(dev));
+	int ret;
+
+	mutex_lock(&st->lock);
+
+	ret = icp10100_enable_regulator(st);
+	if (ret)
+		goto out_unlock;
+
+	/* reset chip */
+	ret = icp10100_send_cmd(st, &icp10100_cmd_soft_reset, NULL, 0);
+
+out_unlock:
+	mutex_unlock(&st->lock);
+	return ret;
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(icp10100_pm, icp10100_suspend, icp10100_resume,
+				 NULL);
+
+static const struct of_device_id icp10100_of_match[] = {
+	{
+		.compatible = "invensense,icp10100",
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, icp10100_of_match);
+
+static const struct i2c_device_id icp10100_id[] = {
+	{ "icp10100", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, icp10100_id);
+
+static struct i2c_driver icp10100_driver = {
+	.driver = {
+		.name = "icp10100",
+		.pm = pm_ptr(&icp10100_pm),
+		.of_match_table = icp10100_of_match,
+	},
+	.probe = icp10100_probe,
+	.id_table = icp10100_id,
+};
+module_i2c_driver(icp10100_driver);
+
+MODULE_AUTHOR("InvenSense, Inc.");
+MODULE_DESCRIPTION("InvenSense icp10100 driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/pressure/mpl115.c b/drivers/iio/pressure/mpl115.c
new file mode 100644
index 000000000..5bf5b9abe
--- /dev/null
+++ b/drivers/iio/pressure/mpl115.c
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * mpl115.c - Support for Freescale MPL115A pressure/temperature sensor
+ *
+ * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net>
+ *
+ * TODO: shutdown pin
+ */
+
+#include <linux/module.h>
+#include <linux/iio/iio.h>
+#include <linux/delay.h>
+
+#include "mpl115.h"
+
+#define MPL115_PADC 0x00 /* pressure ADC output value, MSB first, 10 bit */
+#define MPL115_TADC 0x02 /* temperature ADC output value, MSB first, 10 bit */
+#define MPL115_A0 0x04 /* 12 bit integer, 3 bit fraction */
+#define MPL115_B1 0x06 /* 2 bit integer, 13 bit fraction */
+#define MPL115_B2 0x08 /* 1 bit integer, 14 bit fraction */
+#define MPL115_C12 0x0a /* 0 bit integer, 13 bit fraction */
+#define MPL115_CONVERT 0x12 /* convert temperature and pressure */
+
+struct mpl115_data {
+	struct device *dev;
+	struct mutex lock;
+	s16 a0;
+	s16 b1, b2;
+	s16 c12;
+	const struct mpl115_ops *ops;
+};
+
+static int mpl115_request(struct mpl115_data *data)
+{
+	int ret = data->ops->write(data->dev, MPL115_CONVERT, 0);
+
+	if (ret < 0)
+		return ret;
+
+	usleep_range(3000, 4000);
+
+	return 0;
+}
+
+static int mpl115_comp_pressure(struct mpl115_data *data, int *val, int *val2)
+{
+	int ret;
+	u16 padc, tadc;
+	int a1, y1, pcomp;
+	unsigned kpa;
+
+	mutex_lock(&data->lock);
+	ret = mpl115_request(data);
+	if (ret < 0)
+		goto done;
+
+	ret = data->ops->read(data->dev, MPL115_PADC);
+	if (ret < 0)
+		goto done;
+	padc = ret >> 6;
+
+	ret = data->ops->read(data->dev, MPL115_TADC);
+	if (ret < 0)
+		goto done;
+	tadc = ret >> 6;
+
+	/* see Freescale AN3785 */
+	a1 = data->b1 + ((data->c12 * tadc) >> 11);
+	y1 = (data->a0 << 10) + a1 * padc;
+
+	/* compensated pressure with 4 fractional bits */
+	pcomp = (y1 + ((data->b2 * (int) tadc) >> 1)) >> 9;
+
+	kpa = pcomp * (115 - 50) / 1023 + (50 << 4);
+	*val = kpa >> 4;
+	*val2 = (kpa & 15) * (1000000 >> 4);
+done:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int mpl115_read_temp(struct mpl115_data *data)
+{
+	int ret;
+
+	mutex_lock(&data->lock);
+	ret = mpl115_request(data);
+	if (ret < 0)
+		goto done;
+	ret = data->ops->read(data->dev, MPL115_TADC);
+done:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int mpl115_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct mpl115_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = mpl115_comp_pressure(data, val, val2);
+		if (ret < 0)
+			return ret;
+		return IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_RAW:
+		/* temperature -5.35 C / LSB, 472 LSB is 25 C */
+		ret = mpl115_read_temp(data);
+		if (ret < 0)
+			return ret;
+		*val = ret >> 6;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_OFFSET:
+		*val = -605;
+		*val2 = 750000;
+		return IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_SCALE:
+		*val = -186;
+		*val2 = 915888;
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+	return -EINVAL;
+}
+
+static const struct iio_chan_spec mpl115_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type =
+			BIT(IIO_CHAN_INFO_OFFSET) | BIT(IIO_CHAN_INFO_SCALE),
+	},
+};
+
+static const struct iio_info mpl115_info = {
+	.read_raw = &mpl115_read_raw,
+};
+
+int mpl115_probe(struct device *dev, const char *name,
+			const struct mpl115_ops *ops)
+{
+	struct mpl115_data *data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	data->dev = dev;
+	data->ops = ops;
+	mutex_init(&data->lock);
+
+	indio_dev->info = &mpl115_info;
+	indio_dev->name = name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = mpl115_channels;
+	indio_dev->num_channels = ARRAY_SIZE(mpl115_channels);
+
+	ret = data->ops->init(data->dev);
+	if (ret)
+		return ret;
+
+	ret = data->ops->read(data->dev, MPL115_A0);
+	if (ret < 0)
+		return ret;
+	data->a0 = ret;
+	ret = data->ops->read(data->dev, MPL115_B1);
+	if (ret < 0)
+		return ret;
+	data->b1 = ret;
+	ret = data->ops->read(data->dev, MPL115_B2);
+	if (ret < 0)
+		return ret;
+	data->b2 = ret;
+	ret = data->ops->read(data->dev, MPL115_C12);
+	if (ret < 0)
+		return ret;
+	data->c12 = ret;
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+EXPORT_SYMBOL_NS_GPL(mpl115_probe, IIO_MPL115);
+
+MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
+MODULE_DESCRIPTION("Freescale MPL115 pressure/temperature driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/pressure/mpl115.h b/drivers/iio/pressure/mpl115.h
new file mode 100644
index 000000000..57d55eb8e
--- /dev/null
+++ b/drivers/iio/pressure/mpl115.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Freescale MPL115A pressure/temperature sensor
+ *
+ * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net>
+ * Copyright (c) 2016 Akinobu Mita <akinobu.mita@gmail.com>
+ */
+
+#ifndef _MPL115_H_
+#define _MPL115_H_
+
+struct mpl115_ops {
+	int (*init)(struct device *);
+	int (*read)(struct device *, u8);
+	int (*write)(struct device *, u8, u8);
+};
+
+int mpl115_probe(struct device *dev, const char *name,
+			const struct mpl115_ops *ops);
+
+#endif
diff --git a/drivers/iio/pressure/mpl115_i2c.c b/drivers/iio/pressure/mpl115_i2c.c
new file mode 100644
index 000000000..099ab1c68
--- /dev/null
+++ b/drivers/iio/pressure/mpl115_i2c.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Freescale MPL115A2 pressure/temperature sensor
+ *
+ * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net>
+ *
+ * (7-bit I2C slave address 0x60)
+ *
+ * Datasheet: http://www.nxp.com/files/sensors/doc/data_sheet/MPL115A2.pdf
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+
+#include "mpl115.h"
+
+static int mpl115_i2c_init(struct device *dev)
+{
+	return 0;
+}
+
+static int mpl115_i2c_read(struct device *dev, u8 address)
+{
+	return i2c_smbus_read_word_swapped(to_i2c_client(dev), address);
+}
+
+static int mpl115_i2c_write(struct device *dev, u8 address, u8 value)
+{
+	return i2c_smbus_write_byte_data(to_i2c_client(dev), address, value);
+}
+
+static const struct mpl115_ops mpl115_i2c_ops = {
+	.init = mpl115_i2c_init,
+	.read = mpl115_i2c_read,
+	.write = mpl115_i2c_write,
+};
+
+static int mpl115_i2c_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
+		return -EOPNOTSUPP;
+
+	return mpl115_probe(&client->dev, id->name, &mpl115_i2c_ops);
+}
+
+static const struct i2c_device_id mpl115_i2c_id[] = {
+	{ "mpl115", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, mpl115_i2c_id);
+
+static struct i2c_driver mpl115_i2c_driver = {
+	.driver = {
+		.name	= "mpl115",
+	},
+	.probe = mpl115_i2c_probe,
+	.id_table = mpl115_i2c_id,
+};
+module_i2c_driver(mpl115_i2c_driver);
+
+MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
+MODULE_DESCRIPTION("Freescale MPL115A2 pressure/temperature driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_MPL115);
diff --git a/drivers/iio/pressure/mpl115_spi.c b/drivers/iio/pressure/mpl115_spi.c
new file mode 100644
index 000000000..7feec87e2
--- /dev/null
+++ b/drivers/iio/pressure/mpl115_spi.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Freescale MPL115A1 pressure/temperature sensor
+ *
+ * Copyright (c) 2016 Akinobu Mita <akinobu.mita@gmail.com>
+ *
+ * Datasheet: http://www.nxp.com/files/sensors/doc/data_sheet/MPL115A1.pdf
+ */
+
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+
+#include "mpl115.h"
+
+#define MPL115_SPI_WRITE(address)	((address) << 1)
+#define MPL115_SPI_READ(address)	(0x80 | (address) << 1)
+
+struct mpl115_spi_buf {
+	u8 tx[4];
+	u8 rx[4];
+};
+
+static int mpl115_spi_init(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct mpl115_spi_buf *buf;
+
+	buf = devm_kzalloc(dev, sizeof(*buf), GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	spi_set_drvdata(spi, buf);
+
+	return 0;
+}
+
+static int mpl115_spi_read(struct device *dev, u8 address)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct mpl115_spi_buf *buf = spi_get_drvdata(spi);
+	struct spi_transfer xfer = {
+		.tx_buf = buf->tx,
+		.rx_buf = buf->rx,
+		.len = 4,
+	};
+	int ret;
+
+	buf->tx[0] = MPL115_SPI_READ(address);
+	buf->tx[2] = MPL115_SPI_READ(address + 1);
+
+	ret = spi_sync_transfer(spi, &xfer, 1);
+	if (ret)
+		return ret;
+
+	return (buf->rx[1] << 8) | buf->rx[3];
+}
+
+static int mpl115_spi_write(struct device *dev, u8 address, u8 value)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct mpl115_spi_buf *buf = spi_get_drvdata(spi);
+	struct spi_transfer xfer = {
+		.tx_buf = buf->tx,
+		.len = 2,
+	};
+
+	buf->tx[0] = MPL115_SPI_WRITE(address);
+	buf->tx[1] = value;
+
+	return spi_sync_transfer(spi, &xfer, 1);
+}
+
+static const struct mpl115_ops mpl115_spi_ops = {
+	.init = mpl115_spi_init,
+	.read = mpl115_spi_read,
+	.write = mpl115_spi_write,
+};
+
+static int mpl115_spi_probe(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	return mpl115_probe(&spi->dev, id->name, &mpl115_spi_ops);
+}
+
+static const struct spi_device_id mpl115_spi_ids[] = {
+	{ "mpl115", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(spi, mpl115_spi_ids);
+
+static struct spi_driver mpl115_spi_driver = {
+	.driver = {
+		.name   = "mpl115",
+	},
+	.probe = mpl115_spi_probe,
+	.id_table = mpl115_spi_ids,
+};
+module_spi_driver(mpl115_spi_driver);
+
+MODULE_AUTHOR("Akinobu Mita <akinobu.mita@gmail.com>");
+MODULE_DESCRIPTION("Freescale MPL115A1 pressure/temperature driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_MPL115);
diff --git a/drivers/iio/pressure/mpl3115.c b/drivers/iio/pressure/mpl3115.c
new file mode 100644
index 000000000..2f22aba61
--- /dev/null
+++ b/drivers/iio/pressure/mpl3115.c
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * mpl3115.c - Support for Freescale MPL3115A2 pressure/temperature sensor
+ *
+ * Copyright (c) 2013 Peter Meerwald <pmeerw@pmeerw.net>
+ *
+ * (7-bit I2C slave address 0x60)
+ *
+ * TODO: FIFO buffer, altimeter mode, oversampling, continuous mode,
+ * interrupts, user offset correction, raw mode
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/delay.h>
+
+#define MPL3115_STATUS 0x00
+#define MPL3115_OUT_PRESS 0x01 /* MSB first, 20 bit */
+#define MPL3115_OUT_TEMP 0x04 /* MSB first, 12 bit */
+#define MPL3115_WHO_AM_I 0x0c
+#define MPL3115_CTRL_REG1 0x26
+
+#define MPL3115_DEVICE_ID 0xc4
+
+#define MPL3115_STATUS_PRESS_RDY BIT(2)
+#define MPL3115_STATUS_TEMP_RDY BIT(1)
+
+#define MPL3115_CTRL_RESET BIT(2) /* software reset */
+#define MPL3115_CTRL_OST BIT(1) /* initiate measurement */
+#define MPL3115_CTRL_ACTIVE BIT(0) /* continuous measurement */
+#define MPL3115_CTRL_OS_258MS (BIT(5) | BIT(4)) /* 64x oversampling */
+
+struct mpl3115_data {
+	struct i2c_client *client;
+	struct mutex lock;
+	u8 ctrl_reg1;
+};
+
+static int mpl3115_request(struct mpl3115_data *data)
+{
+	int ret, tries = 15;
+
+	/* trigger measurement */
+	ret = i2c_smbus_write_byte_data(data->client, MPL3115_CTRL_REG1,
+		data->ctrl_reg1 | MPL3115_CTRL_OST);
+	if (ret < 0)
+		return ret;
+
+	while (tries-- > 0) {
+		ret = i2c_smbus_read_byte_data(data->client, MPL3115_CTRL_REG1);
+		if (ret < 0)
+			return ret;
+		/* wait for data ready, i.e. OST cleared */
+		if (!(ret & MPL3115_CTRL_OST))
+			break;
+		msleep(20);
+	}
+
+	if (tries < 0) {
+		dev_err(&data->client->dev, "data not ready\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int mpl3115_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct mpl3115_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		switch (chan->type) {
+		case IIO_PRESSURE: { /* in 0.25 pascal / LSB */
+			__be32 tmp = 0;
+
+			mutex_lock(&data->lock);
+			ret = mpl3115_request(data);
+			if (ret < 0) {
+				mutex_unlock(&data->lock);
+				break;
+			}
+			ret = i2c_smbus_read_i2c_block_data(data->client,
+				MPL3115_OUT_PRESS, 3, (u8 *) &tmp);
+			mutex_unlock(&data->lock);
+			if (ret < 0)
+				break;
+			*val = be32_to_cpu(tmp) >> chan->scan_type.shift;
+			ret = IIO_VAL_INT;
+			break;
+		}
+		case IIO_TEMP: { /* in 0.0625 celsius / LSB */
+			__be16 tmp;
+
+			mutex_lock(&data->lock);
+			ret = mpl3115_request(data);
+			if (ret < 0) {
+				mutex_unlock(&data->lock);
+				break;
+			}
+			ret = i2c_smbus_read_i2c_block_data(data->client,
+				MPL3115_OUT_TEMP, 2, (u8 *) &tmp);
+			mutex_unlock(&data->lock);
+			if (ret < 0)
+				break;
+			*val = sign_extend32(be16_to_cpu(tmp) >> chan->scan_type.shift,
+					     chan->scan_type.realbits - 1);
+			ret = IIO_VAL_INT;
+			break;
+		}
+		default:
+			ret = -EINVAL;
+			break;
+		}
+
+		iio_device_release_direct_mode(indio_dev);
+		return ret;
+
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			*val = 0;
+			*val2 = 250; /* want kilopascal */
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+			*val = 0;
+			*val2 = 62500;
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+	}
+	return -EINVAL;
+}
+
+static irqreturn_t mpl3115_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct mpl3115_data *data = iio_priv(indio_dev);
+	/*
+	 * 32-bit channel + 16-bit channel + padding + ts
+	 * Note that it is possible for only one of the first 2
+	 * channels to be enabled. If that happens, the first element
+	 * of the buffer may be either 16 or 32-bits.  As such we cannot
+	 * use a simple structure definition to express this data layout.
+	 */
+	u8 buffer[16] __aligned(8);
+	int ret, pos = 0;
+
+	mutex_lock(&data->lock);
+	ret = mpl3115_request(data);
+	if (ret < 0) {
+		mutex_unlock(&data->lock);
+		goto done;
+	}
+
+	memset(buffer, 0, sizeof(buffer));
+	if (test_bit(0, indio_dev->active_scan_mask)) {
+		ret = i2c_smbus_read_i2c_block_data(data->client,
+			MPL3115_OUT_PRESS, 3, &buffer[pos]);
+		if (ret < 0) {
+			mutex_unlock(&data->lock);
+			goto done;
+		}
+		pos += 4;
+	}
+
+	if (test_bit(1, indio_dev->active_scan_mask)) {
+		ret = i2c_smbus_read_i2c_block_data(data->client,
+			MPL3115_OUT_TEMP, 2, &buffer[pos]);
+		if (ret < 0) {
+			mutex_unlock(&data->lock);
+			goto done;
+		}
+	}
+	mutex_unlock(&data->lock);
+
+	iio_push_to_buffers_with_timestamp(indio_dev, buffer,
+		iio_get_time_ns(indio_dev));
+
+done:
+	iio_trigger_notify_done(indio_dev->trig);
+	return IRQ_HANDLED;
+}
+
+static const struct iio_chan_spec mpl3115_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 'u',
+			.realbits = 20,
+			.storagebits = 32,
+			.shift = 12,
+			.endianness = IIO_BE,
+		}
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 12,
+			.storagebits = 16,
+			.shift = 4,
+			.endianness = IIO_BE,
+		}
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(2),
+};
+
+static const struct iio_info mpl3115_info = {
+	.read_raw = &mpl3115_read_raw,
+};
+
+static int mpl3115_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct mpl3115_data *data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	ret = i2c_smbus_read_byte_data(client, MPL3115_WHO_AM_I);
+	if (ret < 0)
+		return ret;
+	if (ret != MPL3115_DEVICE_ID)
+		return -ENODEV;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	data->client = client;
+	mutex_init(&data->lock);
+
+	i2c_set_clientdata(client, indio_dev);
+	indio_dev->info = &mpl3115_info;
+	indio_dev->name = id->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = mpl3115_channels;
+	indio_dev->num_channels = ARRAY_SIZE(mpl3115_channels);
+
+	/* software reset, I2C transfer is aborted (fails) */
+	i2c_smbus_write_byte_data(client, MPL3115_CTRL_REG1,
+		MPL3115_CTRL_RESET);
+	msleep(50);
+
+	data->ctrl_reg1 = MPL3115_CTRL_OS_258MS;
+	ret = i2c_smbus_write_byte_data(client, MPL3115_CTRL_REG1,
+		data->ctrl_reg1);
+	if (ret < 0)
+		return ret;
+
+	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+		mpl3115_trigger_handler, NULL);
+	if (ret < 0)
+		return ret;
+
+	ret = iio_device_register(indio_dev);
+	if (ret < 0)
+		goto buffer_cleanup;
+	return 0;
+
+buffer_cleanup:
+	iio_triggered_buffer_cleanup(indio_dev);
+	return ret;
+}
+
+static int mpl3115_standby(struct mpl3115_data *data)
+{
+	return i2c_smbus_write_byte_data(data->client, MPL3115_CTRL_REG1,
+		data->ctrl_reg1 & ~MPL3115_CTRL_ACTIVE);
+}
+
+static void mpl3115_remove(struct i2c_client *client)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+
+	iio_device_unregister(indio_dev);
+	iio_triggered_buffer_cleanup(indio_dev);
+	mpl3115_standby(iio_priv(indio_dev));
+}
+
+static int mpl3115_suspend(struct device *dev)
+{
+	return mpl3115_standby(iio_priv(i2c_get_clientdata(
+		to_i2c_client(dev))));
+}
+
+static int mpl3115_resume(struct device *dev)
+{
+	struct mpl3115_data *data = iio_priv(i2c_get_clientdata(
+		to_i2c_client(dev)));
+
+	return i2c_smbus_write_byte_data(data->client, MPL3115_CTRL_REG1,
+		data->ctrl_reg1);
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(mpl3115_pm_ops, mpl3115_suspend,
+				mpl3115_resume);
+
+static const struct i2c_device_id mpl3115_id[] = {
+	{ "mpl3115", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, mpl3115_id);
+
+static const struct of_device_id mpl3115_of_match[] = {
+	{ .compatible = "fsl,mpl3115" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mpl3115_of_match);
+
+static struct i2c_driver mpl3115_driver = {
+	.driver = {
+		.name	= "mpl3115",
+		.of_match_table = mpl3115_of_match,
+		.pm	= pm_sleep_ptr(&mpl3115_pm_ops),
+	},
+	.probe = mpl3115_probe,
+	.remove = mpl3115_remove,
+	.id_table = mpl3115_id,
+};
+module_i2c_driver(mpl3115_driver);
+
+MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
+MODULE_DESCRIPTION("Freescale MPL3115 pressure/temperature driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/pressure/ms5611.h b/drivers/iio/pressure/ms5611.h
new file mode 100644
index 000000000..550b75b71
--- /dev/null
+++ b/drivers/iio/pressure/ms5611.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * MS5611 pressure and temperature sensor driver
+ *
+ * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
+ *
+ */
+
+#ifndef _MS5611_H
+#define _MS5611_H
+
+#include <linux/device.h>
+#include <linux/iio/iio.h>
+#include <linux/mutex.h>
+
+struct regulator;
+
+#define MS5611_RESET			0x1e
+#define MS5611_READ_ADC			0x00
+#define MS5611_READ_PROM_WORD		0xA0
+#define MS5611_PROM_WORDS_NB		8
+
+enum {
+	MS5611,
+	MS5607,
+};
+
+/*
+ * OverSampling Rate descriptor.
+ * Warning: cmd MUST be kept aligned on a word boundary (see
+ * m5611_spi_read_adc_temp_and_pressure in ms5611_spi.c).
+ */
+struct ms5611_osr {
+	unsigned long conv_usec;
+	u8 cmd;
+	unsigned short rate;
+};
+
+struct ms5611_state {
+	void *client;
+	struct mutex lock;
+
+	const struct ms5611_osr *pressure_osr;
+	const struct ms5611_osr *temp_osr;
+
+	u16 prom[MS5611_PROM_WORDS_NB];
+
+	int (*reset)(struct ms5611_state *st);
+	int (*read_prom_word)(struct ms5611_state *st, int index, u16 *word);
+	int (*read_adc_temp_and_pressure)(struct ms5611_state *st,
+					  s32 *temp, s32 *pressure);
+
+	int (*compensate_temp_and_pressure)(struct ms5611_state *st, s32 *temp,
+					  s32 *pressure);
+	struct regulator *vdd;
+};
+
+int ms5611_probe(struct iio_dev *indio_dev, struct device *dev,
+		 const char *name, int type);
+void ms5611_remove(struct iio_dev *indio_dev);
+
+#endif /* _MS5611_H */
diff --git a/drivers/iio/pressure/ms5611_core.c b/drivers/iio/pressure/ms5611_core.c
new file mode 100644
index 000000000..44cfdbedc
--- /dev/null
+++ b/drivers/iio/pressure/ms5611_core.c
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MS5611 pressure and temperature sensor driver
+ *
+ * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
+ *
+ * Data sheet:
+ *  http://www.meas-spec.com/downloads/MS5611-01BA03.pdf
+ *  http://www.meas-spec.com/downloads/MS5607-02BA03.pdf
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/iio/iio.h>
+#include <linux/delay.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/iio/sysfs.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include "ms5611.h"
+
+#define MS5611_INIT_OSR(_cmd, _conv_usec, _rate) \
+	{ .cmd = _cmd, .conv_usec = _conv_usec, .rate = _rate }
+
+static const struct ms5611_osr ms5611_avail_pressure_osr[] = {
+	MS5611_INIT_OSR(0x40, 600,  256),
+	MS5611_INIT_OSR(0x42, 1170, 512),
+	MS5611_INIT_OSR(0x44, 2280, 1024),
+	MS5611_INIT_OSR(0x46, 4540, 2048),
+	MS5611_INIT_OSR(0x48, 9040, 4096)
+};
+
+static const struct ms5611_osr ms5611_avail_temp_osr[] = {
+	MS5611_INIT_OSR(0x50, 600,  256),
+	MS5611_INIT_OSR(0x52, 1170, 512),
+	MS5611_INIT_OSR(0x54, 2280, 1024),
+	MS5611_INIT_OSR(0x56, 4540, 2048),
+	MS5611_INIT_OSR(0x58, 9040, 4096)
+};
+
+static const char ms5611_show_osr[] = "256 512 1024 2048 4096";
+
+static IIO_CONST_ATTR(oversampling_ratio_available, ms5611_show_osr);
+
+static struct attribute *ms5611_attributes[] = {
+	&iio_const_attr_oversampling_ratio_available.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ms5611_attribute_group = {
+	.attrs = ms5611_attributes,
+};
+
+static bool ms5611_prom_is_valid(u16 *prom, size_t len)
+{
+	int i, j;
+	uint16_t crc = 0, crc_orig = prom[7] & 0x000F;
+
+	prom[7] &= 0xFF00;
+
+	for (i = 0; i < len * 2; i++) {
+		if (i % 2 == 1)
+			crc ^= prom[i >> 1] & 0x00FF;
+		else
+			crc ^= prom[i >> 1] >> 8;
+
+		for (j = 0; j < 8; j++) {
+			if (crc & 0x8000)
+				crc = (crc << 1) ^ 0x3000;
+			else
+				crc <<= 1;
+		}
+	}
+
+	crc = (crc >> 12) & 0x000F;
+
+	return crc == crc_orig;
+}
+
+static int ms5611_read_prom(struct iio_dev *indio_dev)
+{
+	int ret, i;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	for (i = 0; i < MS5611_PROM_WORDS_NB; i++) {
+		ret = st->read_prom_word(st, i, &st->prom[i]);
+		if (ret < 0) {
+			dev_err(&indio_dev->dev,
+				"failed to read prom at %d\n", i);
+			return ret;
+		}
+	}
+
+	if (!ms5611_prom_is_valid(st->prom, MS5611_PROM_WORDS_NB)) {
+		dev_err(&indio_dev->dev, "PROM integrity check failed\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int ms5611_read_temp_and_pressure(struct iio_dev *indio_dev,
+					 s32 *temp, s32 *pressure)
+{
+	int ret;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	ret = st->read_adc_temp_and_pressure(st, temp, pressure);
+	if (ret < 0) {
+		dev_err(&indio_dev->dev,
+			"failed to read temperature and pressure\n");
+		return ret;
+	}
+
+	return st->compensate_temp_and_pressure(st, temp, pressure);
+}
+
+static int ms5611_temp_and_pressure_compensate(struct ms5611_state *st,
+					       s32 *temp, s32 *pressure)
+{
+	s32 t = *temp, p = *pressure;
+	s64 off, sens, dt;
+
+	dt = t - (st->prom[5] << 8);
+	off = ((s64)st->prom[2] << 16) + ((st->prom[4] * dt) >> 7);
+	sens = ((s64)st->prom[1] << 15) + ((st->prom[3] * dt) >> 8);
+
+	t = 2000 + ((st->prom[6] * dt) >> 23);
+	if (t < 2000) {
+		s64 off2, sens2, t2;
+
+		t2 = (dt * dt) >> 31;
+		off2 = (5 * (t - 2000) * (t - 2000)) >> 1;
+		sens2 = off2 >> 1;
+
+		if (t < -1500) {
+			s64 tmp = (t + 1500) * (t + 1500);
+
+			off2 += 7 * tmp;
+			sens2 += (11 * tmp) >> 1;
+		}
+
+		t -= t2;
+		off -= off2;
+		sens -= sens2;
+	}
+
+	*temp = t;
+	*pressure = (((p * sens) >> 21) - off) >> 15;
+
+	return 0;
+}
+
+static int ms5607_temp_and_pressure_compensate(struct ms5611_state *st,
+					       s32 *temp, s32 *pressure)
+{
+	s32 t = *temp, p = *pressure;
+	s64 off, sens, dt;
+
+	dt = t - (st->prom[5] << 8);
+	off = ((s64)st->prom[2] << 17) + ((st->prom[4] * dt) >> 6);
+	sens = ((s64)st->prom[1] << 16) + ((st->prom[3] * dt) >> 7);
+
+	t = 2000 + ((st->prom[6] * dt) >> 23);
+	if (t < 2000) {
+		s64 off2, sens2, t2, tmp;
+
+		t2 = (dt * dt) >> 31;
+		tmp = (t - 2000) * (t - 2000);
+		off2 = (61 * tmp) >> 4;
+		sens2 = tmp << 1;
+
+		if (t < -1500) {
+			tmp = (t + 1500) * (t + 1500);
+			off2 += 15 * tmp;
+			sens2 += 8 * tmp;
+		}
+
+		t -= t2;
+		off -= off2;
+		sens -= sens2;
+	}
+
+	*temp = t;
+	*pressure = (((p * sens) >> 21) - off) >> 15;
+
+	return 0;
+}
+
+static int ms5611_reset(struct iio_dev *indio_dev)
+{
+	int ret;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	ret = st->reset(st);
+	if (ret < 0) {
+		dev_err(&indio_dev->dev, "failed to reset device\n");
+		return ret;
+	}
+
+	usleep_range(3000, 4000);
+
+	return 0;
+}
+
+static irqreturn_t ms5611_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct ms5611_state *st = iio_priv(indio_dev);
+	/* Ensure buffer elements are naturally aligned */
+	struct {
+		s32 channels[2];
+		s64 ts __aligned(8);
+	} scan;
+	int ret;
+
+	mutex_lock(&st->lock);
+	ret = ms5611_read_temp_and_pressure(indio_dev, &scan.channels[1],
+					    &scan.channels[0]);
+	mutex_unlock(&st->lock);
+	if (ret < 0)
+		goto err;
+
+	iio_push_to_buffers_with_timestamp(indio_dev, &scan,
+					   iio_get_time_ns(indio_dev));
+
+err:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+static int ms5611_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	int ret;
+	s32 temp, pressure;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		mutex_lock(&st->lock);
+		ret = ms5611_read_temp_and_pressure(indio_dev,
+						    &temp, &pressure);
+		mutex_unlock(&st->lock);
+		if (ret < 0)
+			return ret;
+
+		switch (chan->type) {
+		case IIO_TEMP:
+			*val = temp * 10;
+			return IIO_VAL_INT;
+		case IIO_PRESSURE:
+			*val = pressure / 1000;
+			*val2 = (pressure % 1000) * 1000;
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_TEMP:
+			*val = 10;
+			return IIO_VAL_INT;
+		case IIO_PRESSURE:
+			*val = 0;
+			*val2 = 1000;
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		if (chan->type != IIO_TEMP && chan->type != IIO_PRESSURE)
+			break;
+		mutex_lock(&st->lock);
+		if (chan->type == IIO_TEMP)
+			*val = (int)st->temp_osr->rate;
+		else
+			*val = (int)st->pressure_osr->rate;
+		mutex_unlock(&st->lock);
+		return IIO_VAL_INT;
+	}
+
+	return -EINVAL;
+}
+
+static const struct ms5611_osr *ms5611_find_osr(int rate,
+						const struct ms5611_osr *osr,
+						size_t count)
+{
+	unsigned int r;
+
+	for (r = 0; r < count; r++)
+		if ((unsigned short)rate == osr[r].rate)
+			break;
+	if (r >= count)
+		return NULL;
+	return &osr[r];
+}
+
+static int ms5611_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct ms5611_state *st = iio_priv(indio_dev);
+	const struct ms5611_osr *osr = NULL;
+	int ret;
+
+	if (mask != IIO_CHAN_INFO_OVERSAMPLING_RATIO)
+		return -EINVAL;
+
+	if (chan->type == IIO_TEMP)
+		osr = ms5611_find_osr(val, ms5611_avail_temp_osr,
+				      ARRAY_SIZE(ms5611_avail_temp_osr));
+	else if (chan->type == IIO_PRESSURE)
+		osr = ms5611_find_osr(val, ms5611_avail_pressure_osr,
+				      ARRAY_SIZE(ms5611_avail_pressure_osr));
+	if (!osr)
+		return -EINVAL;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	mutex_lock(&st->lock);
+
+	if (chan->type == IIO_TEMP)
+		st->temp_osr = osr;
+	else
+		st->pressure_osr = osr;
+
+	mutex_unlock(&st->lock);
+	iio_device_release_direct_mode(indio_dev);
+
+	return 0;
+}
+
+static const unsigned long ms5611_scan_masks[] = {0x3, 0};
+
+static const struct iio_chan_spec ms5611_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 32,
+			.storagebits = 32,
+			.endianness = IIO_CPU,
+		},
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 32,
+			.storagebits = 32,
+			.endianness = IIO_CPU,
+		},
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(2),
+};
+
+static const struct iio_info ms5611_info = {
+	.read_raw = &ms5611_read_raw,
+	.write_raw = &ms5611_write_raw,
+	.attrs = &ms5611_attribute_group,
+};
+
+static int ms5611_init(struct iio_dev *indio_dev)
+{
+	int ret;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	/* Enable attached regulator if any. */
+	st->vdd = devm_regulator_get(indio_dev->dev.parent, "vdd");
+	if (IS_ERR(st->vdd))
+		return PTR_ERR(st->vdd);
+
+	ret = regulator_enable(st->vdd);
+	if (ret) {
+		dev_err(indio_dev->dev.parent,
+			"failed to enable Vdd supply: %d\n", ret);
+		return ret;
+	}
+
+	ret = ms5611_reset(indio_dev);
+	if (ret < 0)
+		goto err_regulator_disable;
+
+	ret = ms5611_read_prom(indio_dev);
+	if (ret < 0)
+		goto err_regulator_disable;
+
+	return 0;
+
+err_regulator_disable:
+	regulator_disable(st->vdd);
+	return ret;
+}
+
+static void ms5611_fini(const struct iio_dev *indio_dev)
+{
+	const struct ms5611_state *st = iio_priv(indio_dev);
+
+	regulator_disable(st->vdd);
+}
+
+int ms5611_probe(struct iio_dev *indio_dev, struct device *dev,
+		 const char *name, int type)
+{
+	int ret;
+	struct ms5611_state *st = iio_priv(indio_dev);
+
+	mutex_init(&st->lock);
+
+	switch (type) {
+	case MS5611:
+		st->compensate_temp_and_pressure =
+			ms5611_temp_and_pressure_compensate;
+		break;
+	case MS5607:
+		st->compensate_temp_and_pressure =
+			ms5607_temp_and_pressure_compensate;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	st->temp_osr =
+		&ms5611_avail_temp_osr[ARRAY_SIZE(ms5611_avail_temp_osr) - 1];
+	st->pressure_osr =
+		&ms5611_avail_pressure_osr[ARRAY_SIZE(ms5611_avail_pressure_osr)
+					   - 1];
+	indio_dev->name = name;
+	indio_dev->info = &ms5611_info;
+	indio_dev->channels = ms5611_channels;
+	indio_dev->num_channels = ARRAY_SIZE(ms5611_channels);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->available_scan_masks = ms5611_scan_masks;
+
+	ret = ms5611_init(indio_dev);
+	if (ret < 0)
+		return ret;
+
+	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+					 ms5611_trigger_handler, NULL);
+	if (ret < 0) {
+		dev_err(dev, "iio triggered buffer setup failed\n");
+		goto err_fini;
+	}
+
+	ret = iio_device_register(indio_dev);
+	if (ret < 0) {
+		dev_err(dev, "unable to register iio device\n");
+		goto err_buffer_cleanup;
+	}
+
+	return 0;
+
+err_buffer_cleanup:
+	iio_triggered_buffer_cleanup(indio_dev);
+err_fini:
+	ms5611_fini(indio_dev);
+	return ret;
+}
+EXPORT_SYMBOL_NS(ms5611_probe, IIO_MS5611);
+
+void ms5611_remove(struct iio_dev *indio_dev)
+{
+	iio_device_unregister(indio_dev);
+	iio_triggered_buffer_cleanup(indio_dev);
+	ms5611_fini(indio_dev);
+}
+EXPORT_SYMBOL_NS(ms5611_remove, IIO_MS5611);
+
+MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
+MODULE_DESCRIPTION("MS5611 core driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/ms5611_i2c.c b/drivers/iio/pressure/ms5611_i2c.c
new file mode 100644
index 000000000..b681a4183
--- /dev/null
+++ b/drivers/iio/pressure/ms5611_i2c.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MS5611 pressure and temperature sensor driver (I2C bus)
+ *
+ * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
+ *
+ * 7-bit I2C slave addresses:
+ *
+ * 0x77 (CSB pin low)
+ * 0x76 (CSB pin high)
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+
+#include <asm/unaligned.h>
+
+#include "ms5611.h"
+
+static int ms5611_i2c_reset(struct ms5611_state *st)
+{
+	return i2c_smbus_write_byte(st->client, MS5611_RESET);
+}
+
+static int ms5611_i2c_read_prom_word(struct ms5611_state *st, int index,
+				     u16 *word)
+{
+	int ret;
+
+	ret = i2c_smbus_read_word_swapped(st->client,
+			MS5611_READ_PROM_WORD + (index << 1));
+	if (ret < 0)
+		return ret;
+
+	*word = ret;
+
+	return 0;
+}
+
+static int ms5611_i2c_read_adc(struct ms5611_state *st, s32 *val)
+{
+	int ret;
+	u8 buf[3];
+
+	ret = i2c_smbus_read_i2c_block_data(st->client, MS5611_READ_ADC,
+					    3, buf);
+	if (ret < 0)
+		return ret;
+
+	*val = get_unaligned_be24(&buf[0]);
+
+	return 0;
+}
+
+static int ms5611_i2c_read_adc_temp_and_pressure(struct ms5611_state *st,
+						 s32 *temp, s32 *pressure)
+{
+	int ret;
+	const struct ms5611_osr *osr = st->temp_osr;
+
+	ret = i2c_smbus_write_byte(st->client, osr->cmd);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
+	ret = ms5611_i2c_read_adc(st, temp);
+	if (ret < 0)
+		return ret;
+
+	osr = st->pressure_osr;
+	ret = i2c_smbus_write_byte(st->client, osr->cmd);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
+	return ms5611_i2c_read_adc(st, pressure);
+}
+
+static int ms5611_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct ms5611_state *st;
+	struct iio_dev *indio_dev;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_WRITE_BYTE |
+				     I2C_FUNC_SMBUS_READ_WORD_DATA |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK))
+		return -EOPNOTSUPP;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	st = iio_priv(indio_dev);
+	i2c_set_clientdata(client, indio_dev);
+	st->reset = ms5611_i2c_reset;
+	st->read_prom_word = ms5611_i2c_read_prom_word;
+	st->read_adc_temp_and_pressure = ms5611_i2c_read_adc_temp_and_pressure;
+	st->client = client;
+
+	return ms5611_probe(indio_dev, &client->dev, id->name, id->driver_data);
+}
+
+static void ms5611_i2c_remove(struct i2c_client *client)
+{
+	ms5611_remove(i2c_get_clientdata(client));
+}
+
+static const struct of_device_id ms5611_i2c_matches[] = {
+	{ .compatible = "meas,ms5611" },
+	{ .compatible = "meas,ms5607" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ms5611_i2c_matches);
+
+static const struct i2c_device_id ms5611_id[] = {
+	{ "ms5611", MS5611 },
+	{ "ms5607", MS5607 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ms5611_id);
+
+static struct i2c_driver ms5611_driver = {
+	.driver = {
+		.name = "ms5611",
+		.of_match_table = ms5611_i2c_matches,
+	},
+	.id_table = ms5611_id,
+	.probe = ms5611_i2c_probe,
+	.remove = ms5611_i2c_remove,
+};
+module_i2c_driver(ms5611_driver);
+
+MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
+MODULE_DESCRIPTION("MS5611 i2c driver");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_MS5611);
diff --git a/drivers/iio/pressure/ms5611_spi.c b/drivers/iio/pressure/ms5611_spi.c
new file mode 100644
index 000000000..a0a7205c9
--- /dev/null
+++ b/drivers/iio/pressure/ms5611_spi.c
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MS5611 pressure and temperature sensor driver (SPI bus)
+ *
+ * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/mod_devicetable.h>
+
+#include <asm/unaligned.h>
+
+#include "ms5611.h"
+
+static int ms5611_spi_reset(struct ms5611_state *st)
+{
+	u8 cmd = MS5611_RESET;
+
+	return spi_write_then_read(st->client, &cmd, 1, NULL, 0);
+}
+
+static int ms5611_spi_read_prom_word(struct ms5611_state *st, int index,
+				     u16 *word)
+{
+	int ret;
+
+	ret = spi_w8r16be(st->client, MS5611_READ_PROM_WORD + (index << 1));
+	if (ret < 0)
+		return ret;
+
+	*word = ret;
+
+	return 0;
+}
+
+static int ms5611_spi_read_adc(struct ms5611_state *st, s32 *val)
+{
+	int ret;
+	u8 buf[3] = { MS5611_READ_ADC };
+
+	ret = spi_write_then_read(st->client, buf, 1, buf, 3);
+	if (ret < 0)
+		return ret;
+
+	*val = get_unaligned_be24(&buf[0]);
+
+	return 0;
+}
+
+static int ms5611_spi_read_adc_temp_and_pressure(struct ms5611_state *st,
+						 s32 *temp, s32 *pressure)
+{
+	int ret;
+	const struct ms5611_osr *osr = st->temp_osr;
+
+	/*
+	 * Warning: &osr->cmd MUST be aligned on a word boundary since used as
+	 * 2nd argument (void*) of spi_write_then_read.
+	 */
+	ret = spi_write_then_read(st->client, &osr->cmd, 1, NULL, 0);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
+	ret = ms5611_spi_read_adc(st, temp);
+	if (ret < 0)
+		return ret;
+
+	osr = st->pressure_osr;
+	ret = spi_write_then_read(st->client, &osr->cmd, 1, NULL, 0);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(osr->conv_usec, osr->conv_usec + (osr->conv_usec / 10UL));
+	return ms5611_spi_read_adc(st, pressure);
+}
+
+static int ms5611_spi_probe(struct spi_device *spi)
+{
+	int ret;
+	struct ms5611_state *st;
+	struct iio_dev *indio_dev;
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	spi_set_drvdata(spi, indio_dev);
+
+	spi->mode = SPI_MODE_0;
+	spi->max_speed_hz = min(spi->max_speed_hz, 20000000U);
+	spi->bits_per_word = 8;
+	ret = spi_setup(spi);
+	if (ret < 0)
+		return ret;
+
+	st = iio_priv(indio_dev);
+	st->reset = ms5611_spi_reset;
+	st->read_prom_word = ms5611_spi_read_prom_word;
+	st->read_adc_temp_and_pressure = ms5611_spi_read_adc_temp_and_pressure;
+	st->client = spi;
+
+	return ms5611_probe(indio_dev, &spi->dev, spi_get_device_id(spi)->name,
+			    spi_get_device_id(spi)->driver_data);
+}
+
+static void ms5611_spi_remove(struct spi_device *spi)
+{
+	ms5611_remove(spi_get_drvdata(spi));
+}
+
+static const struct of_device_id ms5611_spi_matches[] = {
+	{ .compatible = "meas,ms5611" },
+	{ .compatible = "meas,ms5607" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ms5611_spi_matches);
+
+static const struct spi_device_id ms5611_id[] = {
+	{ "ms5611", MS5611 },
+	{ "ms5607", MS5607 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ms5611_id);
+
+static struct spi_driver ms5611_driver = {
+	.driver = {
+		.name = "ms5611",
+		.of_match_table = ms5611_spi_matches
+	},
+	.id_table = ms5611_id,
+	.probe = ms5611_spi_probe,
+	.remove = ms5611_spi_remove,
+};
+module_spi_driver(ms5611_driver);
+
+MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
+MODULE_DESCRIPTION("MS5611 spi driver");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_MS5611);
diff --git a/drivers/iio/pressure/ms5637.c b/drivers/iio/pressure/ms5637.c
new file mode 100644
index 000000000..70c700191
--- /dev/null
+++ b/drivers/iio/pressure/ms5637.c
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ms5637.c - Support for Measurement-Specialties MS5637, MS5805
+ *            MS5837 and MS8607 pressure & temperature sensor
+ *
+ * Copyright (c) 2015 Measurement-Specialties
+ *
+ * (7-bit I2C slave address 0x76)
+ *
+ * Datasheet:
+ *  http://www.meas-spec.com/downloads/MS5637-02BA03.pdf
+ * Datasheet:
+ *  http://www.meas-spec.com/downloads/MS5805-02BA01.pdf
+ * Datasheet:
+ *  http://www.meas-spec.com/downloads/MS5837-30BA.pdf
+ * Datasheet:
+ *  http://www.meas-spec.com/downloads/MS8607-02BA01.pdf
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/stat.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/mutex.h>
+
+#include "../common/ms_sensors/ms_sensors_i2c.h"
+
+struct ms_tp_data {
+	const char *name;
+	const struct ms_tp_hw_data *hw;
+};
+
+static const int ms5637_samp_freq[6] = { 960, 480, 240, 120, 60, 30 };
+
+static ssize_t ms5637_show_samp_freq(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+	struct ms_tp_dev *dev_data = iio_priv(indio_dev);
+	int i, len = 0;
+
+	for (i = 0; i <= dev_data->hw->max_res_index; i++)
+		len += sysfs_emit_at(buf, len, "%u ", ms5637_samp_freq[i]);
+	sysfs_emit_at(buf, len - 1, "\n");
+
+	return len;
+}
+
+static int ms5637_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *channel, int *val,
+			   int *val2, long mask)
+{
+	int ret;
+	int temperature;
+	unsigned int pressure;
+	struct ms_tp_dev *dev_data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = ms_sensors_read_temp_and_pressure(dev_data,
+							&temperature,
+							&pressure);
+		if (ret)
+			return ret;
+
+		switch (channel->type) {
+		case IIO_TEMP:	/* in milli °C */
+			*val = temperature;
+
+			return IIO_VAL_INT;
+		case IIO_PRESSURE:	/* in kPa */
+			*val = pressure / 1000;
+			*val2 = (pressure % 1000) * 1000;
+
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = ms5637_samp_freq[dev_data->res_index];
+
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int ms5637_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct ms_tp_dev *dev_data = iio_priv(indio_dev);
+	int i;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		i = ARRAY_SIZE(ms5637_samp_freq);
+		while (i-- > 0)
+			if (val == ms5637_samp_freq[i])
+				break;
+		if (i < 0)
+			return -EINVAL;
+		dev_data->res_index = i;
+
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_chan_spec ms5637_channels[] = {
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	}
+};
+
+static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(ms5637_show_samp_freq);
+
+static struct attribute *ms5637_attributes[] = {
+	&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ms5637_attribute_group = {
+	.attrs = ms5637_attributes,
+};
+
+static const struct iio_info ms5637_info = {
+	.read_raw = ms5637_read_raw,
+	.write_raw = ms5637_write_raw,
+	.attrs = &ms5637_attribute_group,
+};
+
+static int ms5637_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	const struct ms_tp_data *data;
+	struct ms_tp_dev *dev_data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_READ_WORD_DATA |
+				     I2C_FUNC_SMBUS_WRITE_BYTE |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+		dev_err(&client->dev,
+			"Adapter does not support some i2c transaction\n");
+		return -EOPNOTSUPP;
+	}
+
+	if (id)
+		data = (const struct ms_tp_data *)id->driver_data;
+	else
+		data = device_get_match_data(&client->dev);
+	if (!data)
+		return -EINVAL;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	dev_data = iio_priv(indio_dev);
+	dev_data->client = client;
+	dev_data->res_index = data->hw->max_res_index;
+	dev_data->hw = data->hw;
+	mutex_init(&dev_data->lock);
+
+	indio_dev->info = &ms5637_info;
+	indio_dev->name = data->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = ms5637_channels;
+	indio_dev->num_channels = ARRAY_SIZE(ms5637_channels);
+
+	i2c_set_clientdata(client, indio_dev);
+
+	ret = ms_sensors_reset(client, 0x1E, 3000);
+	if (ret)
+		return ret;
+
+	ret = ms_sensors_tp_read_prom(dev_data);
+	if (ret)
+		return ret;
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static const struct ms_tp_hw_data ms5637_hw_data  = {
+	.prom_len = 7,
+	.max_res_index = 5
+};
+
+static const struct ms_tp_hw_data ms5803_hw_data  = {
+	.prom_len = 8,
+	.max_res_index = 4
+};
+
+static const struct ms_tp_data ms5637_data = { .name = "ms5637", .hw = &ms5637_hw_data };
+
+static const struct ms_tp_data ms5803_data = { .name = "ms5803", .hw = &ms5803_hw_data };
+
+static const struct ms_tp_data ms5805_data = { .name = "ms5805", .hw = &ms5637_hw_data };
+
+static const struct ms_tp_data ms5837_data = { .name = "ms5837", .hw = &ms5637_hw_data };
+
+static const struct ms_tp_data ms8607_data = {
+	.name = "ms8607-temppressure",
+	.hw = &ms5637_hw_data,
+};
+
+static const struct i2c_device_id ms5637_id[] = {
+	{"ms5637", (kernel_ulong_t)&ms5637_data },
+	{"ms5805", (kernel_ulong_t)&ms5805_data },
+	{"ms5837", (kernel_ulong_t)&ms5837_data },
+	{"ms8607-temppressure", (kernel_ulong_t)&ms8607_data },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ms5637_id);
+
+static const struct of_device_id ms5637_of_match[] = {
+	{ .compatible = "meas,ms5637", .data = &ms5637_data },
+	{ .compatible = "meas,ms5803", .data = &ms5803_data },
+	{ .compatible = "meas,ms5805", .data = &ms5805_data },
+	{ .compatible = "meas,ms5837", .data = &ms5837_data },
+	{ .compatible = "meas,ms8607-temppressure", .data = &ms8607_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ms5637_of_match);
+
+static struct i2c_driver ms5637_driver = {
+	.probe = ms5637_probe,
+	.id_table = ms5637_id,
+	.driver = {
+		   .name = "ms5637",
+		   .of_match_table = ms5637_of_match,
+		   },
+};
+
+module_i2c_driver(ms5637_driver);
+
+MODULE_DESCRIPTION("Measurement-Specialties ms5637 temperature & pressure driver");
+MODULE_AUTHOR("William Markezana <william.markezana@meas-spec.com>");
+MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@maplehightech.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_MEAS_SPEC_SENSORS);
diff --git a/drivers/iio/pressure/st_pressure.h b/drivers/iio/pressure/st_pressure.h
new file mode 100644
index 000000000..6e11bea78
--- /dev/null
+++ b/drivers/iio/pressure/st_pressure.h
@@ -0,0 +1,58 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * STMicroelectronics pressures driver
+ *
+ * Copyright 2013 STMicroelectronics Inc.
+ *
+ * Denis Ciocca <denis.ciocca@st.com>
+ * v. 1.0.0
+ */
+
+#ifndef ST_PRESS_H
+#define ST_PRESS_H
+
+#include <linux/types.h>
+#include <linux/iio/common/st_sensors.h>
+
+enum st_press_type {
+	LPS001WP,
+	LPS25H,
+	LPS331AP,
+	LPS22HB,
+	LPS33HW,
+	LPS35HW,
+	LPS22HH,
+	LPS22DF,
+	ST_PRESS_MAX,
+};
+
+#define LPS001WP_PRESS_DEV_NAME		"lps001wp"
+#define LPS25H_PRESS_DEV_NAME		"lps25h"
+#define LPS331AP_PRESS_DEV_NAME		"lps331ap"
+#define LPS22HB_PRESS_DEV_NAME		"lps22hb"
+#define LPS33HW_PRESS_DEV_NAME		"lps33hw"
+#define LPS35HW_PRESS_DEV_NAME		"lps35hw"
+#define LPS22HH_PRESS_DEV_NAME		"lps22hh"
+#define LPS22DF_PRESS_DEV_NAME		"lps22df"
+
+/**
+ * struct st_sensors_platform_data - default press platform data
+ * @drdy_int_pin: default press DRDY is available on INT1 pin.
+ */
+static __maybe_unused const struct st_sensors_platform_data default_press_pdata = {
+	.drdy_int_pin = 1,
+};
+
+#ifdef CONFIG_IIO_BUFFER
+int st_press_allocate_ring(struct iio_dev *indio_dev);
+int st_press_trig_set_state(struct iio_trigger *trig, bool state);
+#define ST_PRESS_TRIGGER_SET_STATE (&st_press_trig_set_state)
+#else /* CONFIG_IIO_BUFFER */
+static inline int st_press_allocate_ring(struct iio_dev *indio_dev)
+{
+	return 0;
+}
+#define ST_PRESS_TRIGGER_SET_STATE NULL
+#endif /* CONFIG_IIO_BUFFER */
+
+#endif /* ST_PRESS_H */
diff --git a/drivers/iio/pressure/st_pressure_buffer.c b/drivers/iio/pressure/st_pressure_buffer.c
new file mode 100644
index 000000000..0dbf357c2
--- /dev/null
+++ b/drivers/iio/pressure/st_pressure_buffer.c
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics pressures driver
+ *
+ * Copyright 2013 STMicroelectronics Inc.
+ *
+ * Denis Ciocca <denis.ciocca@st.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/triggered_buffer.h>
+
+#include <linux/iio/common/st_sensors.h>
+#include "st_pressure.h"
+
+int st_press_trig_set_state(struct iio_trigger *trig, bool state)
+{
+	struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
+
+	return st_sensors_set_dataready_irq(indio_dev, state);
+}
+
+static int st_press_buffer_postenable(struct iio_dev *indio_dev)
+{
+	return st_sensors_set_enable(indio_dev, true);
+}
+
+static int st_press_buffer_predisable(struct iio_dev *indio_dev)
+{
+	return st_sensors_set_enable(indio_dev, false);
+}
+
+static const struct iio_buffer_setup_ops st_press_buffer_setup_ops = {
+	.postenable = &st_press_buffer_postenable,
+	.predisable = &st_press_buffer_predisable,
+};
+
+int st_press_allocate_ring(struct iio_dev *indio_dev)
+{
+	return devm_iio_triggered_buffer_setup(indio_dev->dev.parent, indio_dev,
+		NULL, &st_sensors_trigger_handler, &st_press_buffer_setup_ops);
+}
diff --git a/drivers/iio/pressure/st_pressure_core.c b/drivers/iio/pressure/st_pressure_core.c
new file mode 100644
index 000000000..80176e308
--- /dev/null
+++ b/drivers/iio/pressure/st_pressure_core.c
@@ -0,0 +1,798 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics pressures driver
+ *
+ * Copyright 2013 STMicroelectronics Inc.
+ *
+ * Denis Ciocca <denis.ciocca@st.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
+#include <asm/unaligned.h>
+
+#include <linux/iio/common/st_sensors.h>
+#include "st_pressure.h"
+
+/*
+ * About determining pressure scaling factors
+ * ------------------------------------------
+ *
+ * Datasheets specify typical pressure sensitivity so that pressure is computed
+ * according to the following equation :
+ *     pressure[mBar] = raw / sensitivity
+ * where :
+ *     raw          the 24 bits long raw sampled pressure
+ *     sensitivity  a scaling factor specified by the datasheet in LSB/mBar
+ *
+ * IIO ABI expects pressure to be expressed as kPascal, hence pressure should be
+ * computed according to :
+ *     pressure[kPascal] = pressure[mBar] / 10
+ *                       = raw / (sensitivity * 10)                          (1)
+ *
+ * Finally, st_press_read_raw() returns pressure scaling factor as an
+ * IIO_VAL_INT_PLUS_NANO with a zero integral part and "gain" as decimal part.
+ * Therefore, from (1), "gain" becomes :
+ *     gain = 10^9 / (sensitivity * 10)
+ *          = 10^8 / sensitivity
+ *
+ * About determining temperature scaling factors and offsets
+ * ---------------------------------------------------------
+ *
+ * Datasheets specify typical temperature sensitivity and offset so that
+ * temperature is computed according to the following equation :
+ *     temp[Celsius] = offset[Celsius] + (raw / sensitivity)
+ * where :
+ *     raw          the 16 bits long raw sampled temperature
+ *     offset       a constant specified by the datasheet in degree Celsius
+ *                  (sometimes zero)
+ *     sensitivity  a scaling factor specified by the datasheet in LSB/Celsius
+ *
+ * IIO ABI expects temperature to be expressed as milli degree Celsius such as
+ * user space should compute temperature according to :
+ *     temp[mCelsius] = temp[Celsius] * 10^3
+ *                    = (offset[Celsius] + (raw / sensitivity)) * 10^3
+ *                    = ((offset[Celsius] * sensitivity) + raw) *
+ *                      (10^3 / sensitivity)                                 (2)
+ *
+ * IIO ABI expects user space to apply offset and scaling factors to raw samples
+ * according to :
+ *     temp[mCelsius] = (OFFSET + raw) * SCALE
+ * where :
+ *     OFFSET an arbitrary constant exposed by device
+ *     SCALE  an arbitrary scaling factor exposed by device
+ *
+ * Matching OFFSET and SCALE with members of (2) gives :
+ *     OFFSET = offset[Celsius] * sensitivity                                (3)
+ *     SCALE  = 10^3 / sensitivity                                           (4)
+ *
+ * st_press_read_raw() returns temperature scaling factor as an
+ * IIO_VAL_FRACTIONAL with a 10^3 numerator and "gain2" as denominator.
+ * Therefore, from (3), "gain2" becomes :
+ *     gain2 = sensitivity
+ *
+ * When declared within channel, i.e. for a non zero specified offset,
+ * st_press_read_raw() will return the latter as an IIO_VAL_FRACTIONAL such as :
+ *     numerator = OFFSET * 10^3
+ *     denominator = 10^3
+ * giving from (4):
+ *     numerator = offset[Celsius] * 10^3 * sensitivity
+ *               = offset[mCelsius] * gain2
+ */
+
+#define MCELSIUS_PER_CELSIUS			1000
+
+/* Default pressure sensitivity */
+#define ST_PRESS_LSB_PER_MBAR			4096UL
+#define ST_PRESS_KPASCAL_NANO_SCALE		(100000000UL / \
+						 ST_PRESS_LSB_PER_MBAR)
+
+/* Default temperature sensitivity */
+#define ST_PRESS_LSB_PER_CELSIUS		480UL
+#define ST_PRESS_MILLI_CELSIUS_OFFSET		42500UL
+
+/* FULLSCALE */
+#define ST_PRESS_FS_AVL_1100MB			1100
+#define ST_PRESS_FS_AVL_1260MB			1260
+
+#define ST_PRESS_1_OUT_XL_ADDR			0x28
+#define ST_TEMP_1_OUT_L_ADDR			0x2b
+
+/* LPS001WP pressure resolution */
+#define ST_PRESS_LPS001WP_LSB_PER_MBAR		16UL
+/* LPS001WP temperature resolution */
+#define ST_PRESS_LPS001WP_LSB_PER_CELSIUS	64UL
+/* LPS001WP pressure gain */
+#define ST_PRESS_LPS001WP_FS_AVL_PRESS_GAIN \
+	(100000000UL / ST_PRESS_LPS001WP_LSB_PER_MBAR)
+/* LPS001WP pressure and temp L addresses */
+#define ST_PRESS_LPS001WP_OUT_L_ADDR		0x28
+#define ST_TEMP_LPS001WP_OUT_L_ADDR		0x2a
+
+/* LPS25H pressure and temp L addresses */
+#define ST_PRESS_LPS25H_OUT_XL_ADDR		0x28
+#define ST_TEMP_LPS25H_OUT_L_ADDR		0x2b
+
+/* LPS22HB temperature sensitivity */
+#define ST_PRESS_LPS22HB_LSB_PER_CELSIUS	100UL
+
+static const struct iio_chan_spec st_press_1_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.address = ST_PRESS_1_OUT_XL_ADDR,
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 24,
+			.storagebits = 32,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	{
+		.type = IIO_TEMP,
+		.address = ST_TEMP_1_OUT_L_ADDR,
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 16,
+			.storagebits = 16,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OFFSET),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(2)
+};
+
+static const struct iio_chan_spec st_press_lps001wp_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.address = ST_PRESS_LPS001WP_OUT_L_ADDR,
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 16,
+			.storagebits = 16,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE),
+	},
+	{
+		.type = IIO_TEMP,
+		.address = ST_TEMP_LPS001WP_OUT_L_ADDR,
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 16,
+			.storagebits = 16,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE),
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(2)
+};
+
+static const struct iio_chan_spec st_press_lps22hb_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.address = ST_PRESS_1_OUT_XL_ADDR,
+		.scan_index = 0,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 24,
+			.storagebits = 32,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	{
+		.type = IIO_TEMP,
+		.address = ST_TEMP_1_OUT_L_ADDR,
+		.scan_index = 1,
+		.scan_type = {
+			.sign = 's',
+			.realbits = 16,
+			.storagebits = 16,
+			.endianness = IIO_LE,
+		},
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	IIO_CHAN_SOFT_TIMESTAMP(2)
+};
+
+static const struct st_sensor_settings st_press_sensors_settings[] = {
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS331AP SENSOR
+		 * See LPS331AP datasheet:
+		 * http://www2.st.com/resource/en/datasheet/lps331ap.pdf
+		 */
+		.wai = 0xbb,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS331AP_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_1_channels,
+		.num_ch = ARRAY_SIZE(st_press_1_channels),
+		.odr = {
+			.addr = 0x20,
+			.mask = 0x70,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 7, .value = 0x05 },
+				{ .hz = 13, .value = 0x06 },
+				{ .hz = 25, .value = 0x07 },
+			},
+		},
+		.pw = {
+			.addr = 0x20,
+			.mask = 0x80,
+			.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.addr = 0x23,
+			.mask = 0x30,
+			.fs_avl = {
+				/*
+				 * Pressure and temperature sensitivity values
+				 * as defined in table 3 of LPS331AP datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1260MB,
+					.gain = ST_PRESS_KPASCAL_NANO_SCALE,
+					.gain2 = ST_PRESS_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x20,
+			.mask = 0x04,
+		},
+		.drdy_irq = {
+			.int1 = {
+				.addr = 0x22,
+				.mask = 0x04,
+				.addr_od = 0x22,
+				.mask_od = 0x40,
+			},
+			.int2 = {
+				.addr = 0x22,
+				.mask = 0x20,
+				.addr_od = 0x22,
+				.mask_od = 0x40,
+			},
+			.addr_ihl = 0x22,
+			.mask_ihl = 0x80,
+			.stat_drdy = {
+				.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+				.mask = 0x03,
+			},
+		},
+		.sim = {
+			.addr = 0x20,
+			.value = BIT(0),
+		},
+		.multi_read_bit = true,
+		.bootime = 2,
+	},
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS001WP SENSOR
+		 */
+		.wai = 0xba,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS001WP_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_lps001wp_channels,
+		.num_ch = ARRAY_SIZE(st_press_lps001wp_channels),
+		.odr = {
+			.addr = 0x20,
+			.mask = 0x30,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 7, .value = 0x02 },
+				{ .hz = 13, .value = 0x03 },
+			},
+		},
+		.pw = {
+			.addr = 0x20,
+			.mask = 0x40,
+			.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.fs_avl = {
+				/*
+				 * Pressure and temperature resolution values
+				 * as defined in table 3 of LPS001WP datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1100MB,
+					.gain = ST_PRESS_LPS001WP_FS_AVL_PRESS_GAIN,
+					.gain2 = ST_PRESS_LPS001WP_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x20,
+			.mask = 0x04,
+		},
+		.sim = {
+			.addr = 0x20,
+			.value = BIT(0),
+		},
+		.multi_read_bit = true,
+		.bootime = 2,
+	},
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS25H SENSOR
+		 * See LPS25H datasheet:
+		 * http://www2.st.com/resource/en/datasheet/lps25h.pdf
+		 */
+		.wai = 0xbd,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS25H_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_1_channels,
+		.num_ch = ARRAY_SIZE(st_press_1_channels),
+		.odr = {
+			.addr = 0x20,
+			.mask = 0x70,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 7, .value = 0x02 },
+				{ .hz = 13, .value = 0x03 },
+				{ .hz = 25, .value = 0x04 },
+			},
+		},
+		.pw = {
+			.addr = 0x20,
+			.mask = 0x80,
+			.value_on = ST_SENSORS_DEFAULT_POWER_ON_VALUE,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.fs_avl = {
+				/*
+				 * Pressure and temperature sensitivity values
+				 * as defined in table 3 of LPS25H datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1260MB,
+					.gain = ST_PRESS_KPASCAL_NANO_SCALE,
+					.gain2 = ST_PRESS_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x20,
+			.mask = 0x04,
+		},
+		.drdy_irq = {
+			.int1 = {
+				.addr = 0x23,
+				.mask = 0x01,
+				.addr_od = 0x22,
+				.mask_od = 0x40,
+			},
+			.addr_ihl = 0x22,
+			.mask_ihl = 0x80,
+			.stat_drdy = {
+				.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+				.mask = 0x03,
+			},
+		},
+		.sim = {
+			.addr = 0x20,
+			.value = BIT(0),
+		},
+		.multi_read_bit = true,
+		.bootime = 2,
+	},
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS22HB SENSOR
+		 * See LPS22HB datasheet:
+		 * http://www2.st.com/resource/en/datasheet/lps22hb.pdf
+		 */
+		.wai = 0xb1,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS22HB_PRESS_DEV_NAME,
+			[1] = LPS33HW_PRESS_DEV_NAME,
+			[2] = LPS35HW_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_lps22hb_channels,
+		.num_ch = ARRAY_SIZE(st_press_lps22hb_channels),
+		.odr = {
+			.addr = 0x10,
+			.mask = 0x70,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 10, .value = 0x02 },
+				{ .hz = 25, .value = 0x03 },
+				{ .hz = 50, .value = 0x04 },
+				{ .hz = 75, .value = 0x05 },
+			},
+		},
+		.pw = {
+			.addr = 0x10,
+			.mask = 0x70,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.fs_avl = {
+				/*
+				 * Pressure and temperature sensitivity values
+				 * as defined in table 3 of LPS22HB datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1260MB,
+					.gain = ST_PRESS_KPASCAL_NANO_SCALE,
+					.gain2 = ST_PRESS_LPS22HB_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x10,
+			.mask = 0x02,
+		},
+		.drdy_irq = {
+			.int1 = {
+				.addr = 0x12,
+				.mask = 0x04,
+				.addr_od = 0x12,
+				.mask_od = 0x40,
+			},
+			.addr_ihl = 0x12,
+			.mask_ihl = 0x80,
+			.stat_drdy = {
+				.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+				.mask = 0x03,
+			},
+		},
+		.sim = {
+			.addr = 0x10,
+			.value = BIT(0),
+		},
+		.multi_read_bit = false,
+		.bootime = 2,
+	},
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS22HH SENSOR
+		 * See LPS22HH datasheet:
+		 * http://www2.st.com/resource/en/datasheet/lps22hh.pdf
+		 */
+		.wai = 0xb3,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS22HH_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_lps22hb_channels,
+		.num_ch = ARRAY_SIZE(st_press_lps22hb_channels),
+		.odr = {
+			.addr = 0x10,
+			.mask = 0x70,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 10, .value = 0x02 },
+				{ .hz = 25, .value = 0x03 },
+				{ .hz = 50, .value = 0x04 },
+				{ .hz = 75, .value = 0x05 },
+				{ .hz = 100, .value = 0x06 },
+				{ .hz = 200, .value = 0x07 },
+			},
+		},
+		.pw = {
+			.addr = 0x10,
+			.mask = 0x70,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.fs_avl = {
+				/*
+				 * Pressure and temperature sensitivity values
+				 * as defined in table 3 of LPS22HH datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1260MB,
+					.gain = ST_PRESS_KPASCAL_NANO_SCALE,
+					.gain2 = ST_PRESS_LPS22HB_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x10,
+			.mask = BIT(1),
+		},
+		.drdy_irq = {
+			.int1 = {
+				.addr = 0x12,
+				.mask = BIT(2),
+				.addr_od = 0x11,
+				.mask_od = BIT(5),
+			},
+			.addr_ihl = 0x11,
+			.mask_ihl = BIT(6),
+			.stat_drdy = {
+				.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+				.mask = 0x03,
+			},
+		},
+		.sim = {
+			.addr = 0x10,
+			.value = BIT(0),
+		},
+		.multi_read_bit = false,
+		.bootime = 2,
+	},
+	{
+		/*
+		 * CUSTOM VALUES FOR LPS22DF SENSOR
+		 * See LPS22DF datasheet:
+		 * http://www.st.com/resource/en/datasheet/lps22df.pdf
+		 */
+		.wai = 0xb4,
+		.wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS,
+		.sensors_supported = {
+			[0] = LPS22DF_PRESS_DEV_NAME,
+		},
+		.ch = (struct iio_chan_spec *)st_press_lps22hb_channels,
+		.num_ch = ARRAY_SIZE(st_press_lps22hb_channels),
+		.odr = {
+			.addr = 0x10,
+			.mask = 0x78,
+			.odr_avl = {
+				{ .hz = 1, .value = 0x01 },
+				{ .hz = 4, .value = 0x02 },
+				{ .hz = 10, .value = 0x03 },
+				{ .hz = 25, .value = 0x04 },
+				{ .hz = 50, .value = 0x05 },
+				{ .hz = 75, .value = 0x06 },
+				{ .hz = 100, .value = 0x07 },
+				{ .hz = 200, .value = 0x08 },
+			},
+		},
+		.pw = {
+			.addr = 0x10,
+			.mask = 0x78,
+			.value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE,
+		},
+		.fs = {
+			.fs_avl = {
+				/*
+				 * Pressure and temperature sensitivity values
+				 * as defined in table 2 of LPS22DF datasheet.
+				 */
+				[0] = {
+					.num = ST_PRESS_FS_AVL_1260MB,
+					.gain = ST_PRESS_KPASCAL_NANO_SCALE,
+					.gain2 = ST_PRESS_LPS22HB_LSB_PER_CELSIUS,
+				},
+			},
+		},
+		.bdu = {
+			.addr = 0x11,
+			.mask = BIT(3),
+		},
+		.drdy_irq = {
+			.int1 = {
+				.addr = 0x13,
+				.mask = BIT(5),
+				.addr_od = 0x12,
+				.mask_od = BIT(1),
+			},
+			.addr_ihl = 0x12,
+			.mask_ihl = BIT(3),
+			.stat_drdy = {
+				.addr = ST_SENSORS_DEFAULT_STAT_ADDR,
+				.mask = 0x03,
+			},
+		},
+		.sim = {
+			.addr = 0x0E,
+			.value = BIT(5),
+		},
+		.multi_read_bit = false,
+		.bootime = 2,
+	},
+};
+
+static int st_press_write_raw(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *ch,
+			      int val,
+			      int val2,
+			      long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		if (val2)
+			return -EINVAL;
+
+		return st_sensors_set_odr(indio_dev, val);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int st_press_read_raw(struct iio_dev *indio_dev,
+			struct iio_chan_spec const *ch, int *val,
+							int *val2, long mask)
+{
+	int err;
+	struct st_sensor_data *press_data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		err = st_sensors_read_info_raw(indio_dev, ch, val);
+		if (err < 0)
+			goto read_error;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		switch (ch->type) {
+		case IIO_PRESSURE:
+			*val = 0;
+			*val2 = press_data->current_fullscale->gain;
+			return IIO_VAL_INT_PLUS_NANO;
+		case IIO_TEMP:
+			*val = MCELSIUS_PER_CELSIUS;
+			*val2 = press_data->current_fullscale->gain2;
+			return IIO_VAL_FRACTIONAL;
+		default:
+			err = -EINVAL;
+			goto read_error;
+		}
+
+	case IIO_CHAN_INFO_OFFSET:
+		switch (ch->type) {
+		case IIO_TEMP:
+			*val = ST_PRESS_MILLI_CELSIUS_OFFSET *
+			       press_data->current_fullscale->gain2;
+			*val2 = MCELSIUS_PER_CELSIUS;
+			break;
+		default:
+			err = -EINVAL;
+			goto read_error;
+		}
+
+		return IIO_VAL_FRACTIONAL;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = press_data->odr;
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+
+read_error:
+	return err;
+}
+
+static ST_SENSORS_DEV_ATTR_SAMP_FREQ_AVAIL();
+
+static struct attribute *st_press_attributes[] = {
+	&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group st_press_attribute_group = {
+	.attrs = st_press_attributes,
+};
+
+static const struct iio_info press_info = {
+	.attrs = &st_press_attribute_group,
+	.read_raw = &st_press_read_raw,
+	.write_raw = &st_press_write_raw,
+	.debugfs_reg_access = &st_sensors_debugfs_reg_access,
+};
+
+#ifdef CONFIG_IIO_TRIGGER
+static const struct iio_trigger_ops st_press_trigger_ops = {
+	.set_trigger_state = ST_PRESS_TRIGGER_SET_STATE,
+	.validate_device = st_sensors_validate_device,
+};
+#define ST_PRESS_TRIGGER_OPS (&st_press_trigger_ops)
+#else
+#define ST_PRESS_TRIGGER_OPS NULL
+#endif
+
+/*
+ * st_press_get_settings() - get sensor settings from device name
+ * @name: device name buffer reference.
+ *
+ * Return: valid reference on success, NULL otherwise.
+ */
+const struct st_sensor_settings *st_press_get_settings(const char *name)
+{
+	int index = st_sensors_get_settings_index(name,
+					st_press_sensors_settings,
+					ARRAY_SIZE(st_press_sensors_settings));
+	if (index < 0)
+		return NULL;
+
+	return &st_press_sensors_settings[index];
+}
+EXPORT_SYMBOL_NS(st_press_get_settings, IIO_ST_SENSORS);
+
+int st_press_common_probe(struct iio_dev *indio_dev)
+{
+	struct st_sensor_data *press_data = iio_priv(indio_dev);
+	struct device *parent = indio_dev->dev.parent;
+	struct st_sensors_platform_data *pdata = dev_get_platdata(parent);
+	int err;
+
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &press_info;
+
+	err = st_sensors_verify_id(indio_dev);
+	if (err < 0)
+		return err;
+
+	/*
+	 * Skip timestamping channel while declaring available channels to
+	 * common st_sensor layer. Look at st_sensors_get_buffer_element() to
+	 * see how timestamps are explicitly pushed as last samples block
+	 * element.
+	 */
+	press_data->num_data_channels = press_data->sensor_settings->num_ch - 1;
+	indio_dev->channels = press_data->sensor_settings->ch;
+	indio_dev->num_channels = press_data->sensor_settings->num_ch;
+
+	press_data->current_fullscale = &press_data->sensor_settings->fs.fs_avl[0];
+
+	press_data->odr = press_data->sensor_settings->odr.odr_avl[0].hz;
+
+	/* Some devices don't support a data ready pin. */
+	if (!pdata && (press_data->sensor_settings->drdy_irq.int1.addr ||
+		       press_data->sensor_settings->drdy_irq.int2.addr))
+		pdata =	(struct st_sensors_platform_data *)&default_press_pdata;
+
+	err = st_sensors_init_sensor(indio_dev, pdata);
+	if (err < 0)
+		return err;
+
+	err = st_press_allocate_ring(indio_dev);
+	if (err < 0)
+		return err;
+
+	if (press_data->irq > 0) {
+		err = st_sensors_allocate_trigger(indio_dev,
+						  ST_PRESS_TRIGGER_OPS);
+		if (err < 0)
+			return err;
+	}
+
+	return devm_iio_device_register(parent, indio_dev);
+}
+EXPORT_SYMBOL_NS(st_press_common_probe, IIO_ST_SENSORS);
+
+MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics pressures driver");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ST_SENSORS);
diff --git a/drivers/iio/pressure/st_pressure_i2c.c b/drivers/iio/pressure/st_pressure_i2c.c
new file mode 100644
index 000000000..58fede861
--- /dev/null
+++ b/drivers/iio/pressure/st_pressure_i2c.c
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics pressures driver
+ *
+ * Copyright 2013 STMicroelectronics Inc.
+ *
+ * Denis Ciocca <denis.ciocca@st.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+
+#include <linux/iio/common/st_sensors.h>
+#include <linux/iio/common/st_sensors_i2c.h>
+#include "st_pressure.h"
+
+static const struct of_device_id st_press_of_match[] = {
+	{
+		.compatible = "st,lps001wp-press",
+		.data = LPS001WP_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps25h-press",
+		.data = LPS25H_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps331ap-press",
+		.data = LPS331AP_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22hb-press",
+		.data = LPS22HB_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps33hw",
+		.data = LPS33HW_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps35hw",
+		.data = LPS35HW_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22hh",
+		.data = LPS22HH_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22df",
+		.data = LPS22DF_PRESS_DEV_NAME,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, st_press_of_match);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id st_press_acpi_match[] = {
+	{"SNO9210", LPS22HB},
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, st_press_acpi_match);
+#endif
+
+static const struct i2c_device_id st_press_id_table[] = {
+	{ LPS001WP_PRESS_DEV_NAME, LPS001WP },
+	{ LPS25H_PRESS_DEV_NAME,  LPS25H },
+	{ LPS331AP_PRESS_DEV_NAME, LPS331AP },
+	{ LPS22HB_PRESS_DEV_NAME, LPS22HB },
+	{ LPS33HW_PRESS_DEV_NAME, LPS33HW },
+	{ LPS35HW_PRESS_DEV_NAME, LPS35HW },
+	{ LPS22HH_PRESS_DEV_NAME, LPS22HH },
+	{ LPS22DF_PRESS_DEV_NAME, LPS22DF },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, st_press_id_table);
+
+static int st_press_i2c_probe(struct i2c_client *client,
+			      const struct i2c_device_id *id)
+{
+	const struct st_sensor_settings *settings;
+	struct st_sensor_data *press_data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	st_sensors_dev_name_probe(&client->dev, client->name, sizeof(client->name));
+
+	settings = st_press_get_settings(client->name);
+	if (!settings) {
+		dev_err(&client->dev, "device name %s not recognized.\n",
+			client->name);
+		return -ENODEV;
+	}
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*press_data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	press_data = iio_priv(indio_dev);
+	press_data->sensor_settings = (struct st_sensor_settings *)settings;
+
+	ret = st_sensors_i2c_configure(indio_dev, client);
+	if (ret < 0)
+		return ret;
+
+	ret = st_sensors_power_enable(indio_dev);
+	if (ret)
+		return ret;
+
+	return st_press_common_probe(indio_dev);
+}
+
+static struct i2c_driver st_press_driver = {
+	.driver = {
+		.name = "st-press-i2c",
+		.of_match_table = st_press_of_match,
+		.acpi_match_table = ACPI_PTR(st_press_acpi_match),
+	},
+	.probe = st_press_i2c_probe,
+	.id_table = st_press_id_table,
+};
+module_i2c_driver(st_press_driver);
+
+MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics pressures i2c driver");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ST_SENSORS);
diff --git a/drivers/iio/pressure/st_pressure_spi.c b/drivers/iio/pressure/st_pressure_spi.c
new file mode 100644
index 000000000..25cca5ad7
--- /dev/null
+++ b/drivers/iio/pressure/st_pressure_spi.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics pressures driver
+ *
+ * Copyright 2013 STMicroelectronics Inc.
+ *
+ * Denis Ciocca <denis.ciocca@st.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/spi/spi.h>
+#include <linux/iio/iio.h>
+
+#include <linux/iio/common/st_sensors.h>
+#include <linux/iio/common/st_sensors_spi.h>
+#include "st_pressure.h"
+
+/*
+ * For new single-chip sensors use <device_name> as compatible string.
+ * For old single-chip devices keep <device_name>-press to maintain
+ * compatibility
+ */
+static const struct of_device_id st_press_of_match[] = {
+	{
+		.compatible = "st,lps001wp-press",
+		.data = LPS001WP_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps25h-press",
+		.data = LPS25H_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps331ap-press",
+		.data = LPS331AP_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22hb-press",
+		.data = LPS22HB_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps33hw",
+		.data = LPS33HW_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps35hw",
+		.data = LPS35HW_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22hh",
+		.data = LPS22HH_PRESS_DEV_NAME,
+	},
+	{
+		.compatible = "st,lps22df",
+		.data = LPS22DF_PRESS_DEV_NAME,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, st_press_of_match);
+
+static int st_press_spi_probe(struct spi_device *spi)
+{
+	const struct st_sensor_settings *settings;
+	struct st_sensor_data *press_data;
+	struct iio_dev *indio_dev;
+	int err;
+
+	st_sensors_dev_name_probe(&spi->dev, spi->modalias, sizeof(spi->modalias));
+
+	settings = st_press_get_settings(spi->modalias);
+	if (!settings) {
+		dev_err(&spi->dev, "device name %s not recognized.\n",
+			spi->modalias);
+		return -ENODEV;
+	}
+
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*press_data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	press_data = iio_priv(indio_dev);
+	press_data->sensor_settings = (struct st_sensor_settings *)settings;
+
+	err = st_sensors_spi_configure(indio_dev, spi);
+	if (err < 0)
+		return err;
+
+	err = st_sensors_power_enable(indio_dev);
+	if (err)
+		return err;
+
+	return st_press_common_probe(indio_dev);
+}
+
+static const struct spi_device_id st_press_id_table[] = {
+	{ LPS001WP_PRESS_DEV_NAME },
+	{ LPS25H_PRESS_DEV_NAME },
+	{ LPS331AP_PRESS_DEV_NAME },
+	{ LPS22HB_PRESS_DEV_NAME },
+	{ LPS33HW_PRESS_DEV_NAME },
+	{ LPS35HW_PRESS_DEV_NAME },
+	{ LPS22HH_PRESS_DEV_NAME },
+	{ LPS22DF_PRESS_DEV_NAME },
+	{ "lps001wp-press" },
+	{ "lps25h-press", },
+	{ "lps331ap-press" },
+	{ "lps22hb-press" },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, st_press_id_table);
+
+static struct spi_driver st_press_driver = {
+	.driver = {
+		.name = "st-press-spi",
+		.of_match_table = st_press_of_match,
+	},
+	.probe = st_press_spi_probe,
+	.id_table = st_press_id_table,
+};
+module_spi_driver(st_press_driver);
+
+MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics pressures spi driver");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ST_SENSORS);
diff --git a/drivers/iio/pressure/t5403.c b/drivers/iio/pressure/t5403.c
new file mode 100644
index 000000000..685fcf653
--- /dev/null
+++ b/drivers/iio/pressure/t5403.c
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * t5403.c - Support for EPCOS T5403 pressure/temperature sensor
+ *
+ * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net>
+ *
+ * (7-bit I2C slave address 0x77)
+ *
+ * TODO: end-of-conversion irq
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/delay.h>
+
+#define T5403_DATA 0xf5 /* data, LSB first, 16 bit */
+#define T5403_CALIB_DATA 0x8e /* 10 calibration coeff., LSB first, 16 bit */
+#define T5403_SLAVE_ADDR 0x88 /* I2C slave address, 0x77 */
+#define T5403_COMMAND 0xf1
+
+/* command bits */
+#define T5403_MODE_SHIFT 3 /* conversion time: 2, 8, 16, 66 ms */
+#define T5403_PT BIT(1) /* 0 .. pressure, 1 .. temperature measurement */
+#define T5403_SCO BIT(0) /* start conversion */
+
+#define T5403_MODE_LOW 0
+#define T5403_MODE_STANDARD 1
+#define T5403_MODE_HIGH 2
+#define T5403_MODE_ULTRA_HIGH 3
+
+#define T5403_I2C_MASK (~BIT(7))
+#define T5403_I2C_ADDR 0x77
+
+static const int t5403_pressure_conv_ms[] = {2, 8, 16, 66};
+
+struct t5403_data {
+	struct i2c_client *client;
+	struct mutex lock;
+	int mode;
+	__le16 c[10];
+};
+
+#define T5403_C_U16(i) le16_to_cpu(data->c[(i) - 1])
+#define T5403_C(i) sign_extend32(T5403_C_U16(i), 15)
+
+static int t5403_read(struct t5403_data *data, bool pressure)
+{
+	int wait_time = 3;  /* wakeup time in ms */
+
+	int ret = i2c_smbus_write_byte_data(data->client, T5403_COMMAND,
+		(pressure ? (data->mode << T5403_MODE_SHIFT) : T5403_PT) |
+		T5403_SCO);
+	if (ret < 0)
+		return ret;
+
+	wait_time += pressure ? t5403_pressure_conv_ms[data->mode] : 2;
+
+	msleep(wait_time);
+
+	return i2c_smbus_read_word_data(data->client, T5403_DATA);
+}
+
+static int t5403_comp_pressure(struct t5403_data *data, int *val, int *val2)
+{
+	int ret;
+	s16 t_r;
+	u16 p_r;
+	s32 S, O, X;
+
+	mutex_lock(&data->lock);
+
+	ret = t5403_read(data, false);
+	if (ret < 0)
+		goto done;
+	t_r = ret;
+
+	ret = t5403_read(data, true);
+	if (ret < 0)
+		goto done;
+	p_r = ret;
+
+	/* see EPCOS application note */
+	S = T5403_C_U16(3) + (s32) T5403_C_U16(4) * t_r / 0x20000 +
+		T5403_C(5) * t_r / 0x8000 * t_r / 0x80000 +
+		T5403_C(9) * t_r / 0x8000 * t_r / 0x8000 * t_r / 0x10000;
+
+	O = T5403_C(6) * 0x4000 + T5403_C(7) * t_r / 8 +
+		T5403_C(8) * t_r / 0x8000 * t_r / 16 +
+		T5403_C(9) * t_r / 0x8000 * t_r / 0x10000 * t_r;
+
+	X = (S * p_r + O) / 0x4000;
+
+	X += ((X - 75000) * (X - 75000) / 0x10000 - 9537) *
+	    T5403_C(10) / 0x10000;
+
+	*val = X / 1000;
+	*val2 = (X % 1000) * 1000;
+
+done:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int t5403_comp_temp(struct t5403_data *data, int *val)
+{
+	int ret;
+	s16 t_r;
+
+	mutex_lock(&data->lock);
+	ret = t5403_read(data, false);
+	if (ret < 0)
+		goto done;
+	t_r = ret;
+
+	/* see EPCOS application note */
+	*val = ((s32) T5403_C_U16(1) * t_r / 0x100 +
+		(s32) T5403_C_U16(2) * 0x40) * 1000 / 0x10000;
+
+done:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int t5403_read_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan,
+			  int *val, int *val2, long mask)
+{
+	struct t5403_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			ret = t5403_comp_pressure(data, val, val2);
+			if (ret < 0)
+				return ret;
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+			ret = t5403_comp_temp(data, val);
+			if (ret < 0)
+				return ret;
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+	    }
+	case IIO_CHAN_INFO_INT_TIME:
+		*val = 0;
+		*val2 = t5403_pressure_conv_ms[data->mode] * 1000;
+		return IIO_VAL_INT_PLUS_MICRO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int t5403_write_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int val, int val2, long mask)
+{
+	struct t5403_data *data = iio_priv(indio_dev);
+	int i;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_INT_TIME:
+		if (val != 0)
+			return -EINVAL;
+		for (i = 0; i < ARRAY_SIZE(t5403_pressure_conv_ms); i++)
+			if (val2 == t5403_pressure_conv_ms[i] * 1000) {
+				mutex_lock(&data->lock);
+				data->mode = i;
+				mutex_unlock(&data->lock);
+				return 0;
+			}
+		return -EINVAL;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_chan_spec t5403_channels[] = {
+	{
+		.type = IIO_PRESSURE,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
+		    BIT(IIO_CHAN_INFO_INT_TIME),
+	},
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+	},
+};
+
+static IIO_CONST_ATTR_INT_TIME_AVAIL("0.002 0.008 0.016 0.066");
+
+static struct attribute *t5403_attributes[] = {
+	&iio_const_attr_integration_time_available.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group t5403_attribute_group = {
+	.attrs = t5403_attributes,
+};
+
+static const struct iio_info t5403_info = {
+	.read_raw = &t5403_read_raw,
+	.write_raw = &t5403_write_raw,
+	.attrs = &t5403_attribute_group,
+};
+
+static int t5403_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct t5403_data *data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA |
+	    I2C_FUNC_SMBUS_I2C_BLOCK))
+		return -EOPNOTSUPP;
+
+	ret = i2c_smbus_read_byte_data(client, T5403_SLAVE_ADDR);
+	if (ret < 0)
+		return ret;
+	if ((ret & T5403_I2C_MASK) != T5403_I2C_ADDR)
+		return -ENODEV;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	data->client = client;
+	mutex_init(&data->lock);
+
+	i2c_set_clientdata(client, indio_dev);
+	indio_dev->info = &t5403_info;
+	indio_dev->name = id->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = t5403_channels;
+	indio_dev->num_channels = ARRAY_SIZE(t5403_channels);
+
+	data->mode = T5403_MODE_STANDARD;
+
+	ret = i2c_smbus_read_i2c_block_data(data->client, T5403_CALIB_DATA,
+	    sizeof(data->c), (u8 *) data->c);
+	if (ret < 0)
+		return ret;
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static const struct i2c_device_id t5403_id[] = {
+	{ "t5403", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, t5403_id);
+
+static struct i2c_driver t5403_driver = {
+	.driver = {
+		.name	= "t5403",
+	},
+	.probe = t5403_probe,
+	.id_table = t5403_id,
+};
+module_i2c_driver(t5403_driver);
+
+MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
+MODULE_DESCRIPTION("EPCOS T5403 pressure/temperature sensor driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/pressure/zpa2326.c b/drivers/iio/pressure/zpa2326.c
new file mode 100644
index 000000000..67119a9b9
--- /dev/null
+++ b/drivers/iio/pressure/zpa2326.c
@@ -0,0 +1,1716 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Murata ZPA2326 pressure and temperature sensor IIO driver
+ *
+ * Copyright (c) 2016 Parrot S.A.
+ *
+ * Author: Gregor Boirie <gregor.boirie@parrot.com>
+ */
+
+/**
+ * DOC: ZPA2326 theory of operations
+ *
+ * This driver supports %INDIO_DIRECT_MODE and %INDIO_BUFFER_TRIGGERED IIO
+ * modes.
+ * A internal hardware trigger is also implemented to dispatch registered IIO
+ * trigger consumers upon "sample ready" interrupts.
+ *
+ * ZPA2326 hardware supports 2 sampling mode: one shot and continuous.
+ *
+ * A complete one shot sampling cycle gets device out of low power mode,
+ * performs pressure and temperature measurements, then automatically switches
+ * back to low power mode. It is meant for on demand sampling with optimal power
+ * saving at the cost of lower sampling rate and higher software overhead.
+ * This is a natural candidate for IIO read_raw hook implementation
+ * (%INDIO_DIRECT_MODE). It is also used for triggered buffering support to
+ * ensure explicit synchronization with external trigger events
+ * (%INDIO_BUFFER_TRIGGERED).
+ *
+ * The continuous mode works according to a periodic hardware measurement
+ * process continuously pushing samples into an internal hardware FIFO (for
+ * pressure samples only). Measurement cycle completion may be signaled by a
+ * "sample ready" interrupt.
+ * Typical software sequence of operations :
+ * - get device out of low power mode,
+ * - setup hardware sampling period,
+ * - at end of period, upon data ready interrupt: pop pressure samples out of
+ *   hardware FIFO and fetch temperature sample
+ * - when no longer needed, stop sampling process by putting device into
+ *   low power mode.
+ * This mode is used to implement %INDIO_BUFFER_TRIGGERED mode if device tree
+ * declares a valid interrupt line. In this case, the internal hardware trigger
+ * drives acquisition.
+ *
+ * Note that hardware sampling frequency is taken into account only when
+ * internal hardware trigger is attached as the highest sampling rate seems to
+ * be the most energy efficient.
+ *
+ * TODO:
+ *   preset pressure threshold crossing / IIO events ;
+ *   differential pressure sampling ;
+ *   hardware samples averaging.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/consumer.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <asm/unaligned.h>
+#include "zpa2326.h"
+
+/* 200 ms should be enough for the longest conversion time in one-shot mode. */
+#define ZPA2326_CONVERSION_JIFFIES (HZ / 5)
+
+/* There should be a 1 ms delay (Tpup) after getting out of reset. */
+#define ZPA2326_TPUP_USEC_MIN      (1000)
+#define ZPA2326_TPUP_USEC_MAX      (2000)
+
+/**
+ * struct zpa2326_frequency - Hardware sampling frequency descriptor
+ * @hz : Frequency in Hertz.
+ * @odr: Output Data Rate word as expected by %ZPA2326_CTRL_REG3_REG.
+ */
+struct zpa2326_frequency {
+	int hz;
+	u16 odr;
+};
+
+/*
+ * Keep these in strict ascending order: last array entry is expected to
+ * correspond to the highest sampling frequency.
+ */
+static const struct zpa2326_frequency zpa2326_sampling_frequencies[] = {
+	{ .hz = 1,  .odr = 1 << ZPA2326_CTRL_REG3_ODR_SHIFT },
+	{ .hz = 5,  .odr = 5 << ZPA2326_CTRL_REG3_ODR_SHIFT },
+	{ .hz = 11, .odr = 6 << ZPA2326_CTRL_REG3_ODR_SHIFT },
+	{ .hz = 23, .odr = 7 << ZPA2326_CTRL_REG3_ODR_SHIFT },
+};
+
+/* Return the highest hardware sampling frequency available. */
+static const struct zpa2326_frequency *zpa2326_highest_frequency(void)
+{
+	return &zpa2326_sampling_frequencies[
+		ARRAY_SIZE(zpa2326_sampling_frequencies) - 1];
+}
+
+/**
+ * struct zpa2326_private - Per-device internal private state
+ * @timestamp:  Buffered samples ready datum.
+ * @regmap:     Underlying I2C / SPI bus adapter used to abstract slave register
+ *              accesses.
+ * @result:     Allows sampling logic to get completion status of operations
+ *              that interrupt handlers perform asynchronously.
+ * @data_ready: Interrupt handler uses this to wake user context up at sampling
+ *              operation completion.
+ * @trigger:    Optional hardware / interrupt driven trigger used to notify
+ *              external devices a new sample is ready.
+ * @waken:      Flag indicating whether or not device has just been powered on.
+ * @irq:        Optional interrupt line: negative or zero if not declared into
+ *              DT, in which case sampling logic keeps polling status register
+ *              to detect completion.
+ * @frequency:  Current hardware sampling frequency.
+ * @vref:       Power / voltage reference.
+ * @vdd:        Power supply.
+ */
+struct zpa2326_private {
+	s64                             timestamp;
+	struct regmap                  *regmap;
+	int                             result;
+	struct completion               data_ready;
+	struct iio_trigger             *trigger;
+	bool                            waken;
+	int                             irq;
+	const struct zpa2326_frequency *frequency;
+	struct regulator               *vref;
+	struct regulator               *vdd;
+};
+
+#define zpa2326_err(idev, fmt, ...)					\
+	dev_err(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
+
+#define zpa2326_warn(idev, fmt, ...)					\
+	dev_warn(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
+
+#define zpa2326_dbg(idev, fmt, ...)					\
+	dev_dbg(idev->dev.parent, fmt "\n", ##__VA_ARGS__)
+
+bool zpa2326_isreg_writeable(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case ZPA2326_REF_P_XL_REG:
+	case ZPA2326_REF_P_L_REG:
+	case ZPA2326_REF_P_H_REG:
+	case ZPA2326_RES_CONF_REG:
+	case ZPA2326_CTRL_REG0_REG:
+	case ZPA2326_CTRL_REG1_REG:
+	case ZPA2326_CTRL_REG2_REG:
+	case ZPA2326_CTRL_REG3_REG:
+	case ZPA2326_THS_P_LOW_REG:
+	case ZPA2326_THS_P_HIGH_REG:
+		return true;
+
+	default:
+		return false;
+	}
+}
+EXPORT_SYMBOL_NS_GPL(zpa2326_isreg_writeable, IIO_ZPA2326);
+
+bool zpa2326_isreg_readable(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case ZPA2326_REF_P_XL_REG:
+	case ZPA2326_REF_P_L_REG:
+	case ZPA2326_REF_P_H_REG:
+	case ZPA2326_DEVICE_ID_REG:
+	case ZPA2326_RES_CONF_REG:
+	case ZPA2326_CTRL_REG0_REG:
+	case ZPA2326_CTRL_REG1_REG:
+	case ZPA2326_CTRL_REG2_REG:
+	case ZPA2326_CTRL_REG3_REG:
+	case ZPA2326_INT_SOURCE_REG:
+	case ZPA2326_THS_P_LOW_REG:
+	case ZPA2326_THS_P_HIGH_REG:
+	case ZPA2326_STATUS_REG:
+	case ZPA2326_PRESS_OUT_XL_REG:
+	case ZPA2326_PRESS_OUT_L_REG:
+	case ZPA2326_PRESS_OUT_H_REG:
+	case ZPA2326_TEMP_OUT_L_REG:
+	case ZPA2326_TEMP_OUT_H_REG:
+		return true;
+
+	default:
+		return false;
+	}
+}
+EXPORT_SYMBOL_NS_GPL(zpa2326_isreg_readable, IIO_ZPA2326);
+
+bool zpa2326_isreg_precious(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case ZPA2326_INT_SOURCE_REG:
+	case ZPA2326_PRESS_OUT_H_REG:
+		return true;
+
+	default:
+		return false;
+	}
+}
+EXPORT_SYMBOL_NS_GPL(zpa2326_isreg_precious, IIO_ZPA2326);
+
+/**
+ * zpa2326_enable_device() - Enable device, i.e. get out of low power mode.
+ * @indio_dev: The IIO device associated with the hardware to enable.
+ *
+ * Required to access complete register space and to perform any sampling
+ * or control operations.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_enable_device(const struct iio_dev *indio_dev)
+{
+	int err;
+
+	err = regmap_write(((struct zpa2326_private *)
+			    iio_priv(indio_dev))->regmap,
+			    ZPA2326_CTRL_REG0_REG, ZPA2326_CTRL_REG0_ENABLE);
+	if (err) {
+		zpa2326_err(indio_dev, "failed to enable device (%d)", err);
+		return err;
+	}
+
+	zpa2326_dbg(indio_dev, "enabled");
+
+	return 0;
+}
+
+/**
+ * zpa2326_sleep() - Disable device, i.e. switch to low power mode.
+ * @indio_dev: The IIO device associated with the hardware to disable.
+ *
+ * Only %ZPA2326_DEVICE_ID_REG and %ZPA2326_CTRL_REG0_REG registers may be
+ * accessed once device is in the disabled state.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_sleep(const struct iio_dev *indio_dev)
+{
+	int err;
+
+	err = regmap_write(((struct zpa2326_private *)
+			    iio_priv(indio_dev))->regmap,
+			    ZPA2326_CTRL_REG0_REG, 0);
+	if (err) {
+		zpa2326_err(indio_dev, "failed to sleep (%d)", err);
+		return err;
+	}
+
+	zpa2326_dbg(indio_dev, "sleeping");
+
+	return 0;
+}
+
+/**
+ * zpa2326_reset_device() - Reset device to default hardware state.
+ * @indio_dev: The IIO device associated with the hardware to reset.
+ *
+ * Disable sampling and empty hardware FIFO.
+ * Device must be enabled before reset, i.e. not in low power mode.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_reset_device(const struct iio_dev *indio_dev)
+{
+	int err;
+
+	err = regmap_write(((struct zpa2326_private *)
+			    iio_priv(indio_dev))->regmap,
+			    ZPA2326_CTRL_REG2_REG, ZPA2326_CTRL_REG2_SWRESET);
+	if (err) {
+		zpa2326_err(indio_dev, "failed to reset device (%d)", err);
+		return err;
+	}
+
+	usleep_range(ZPA2326_TPUP_USEC_MIN, ZPA2326_TPUP_USEC_MAX);
+
+	zpa2326_dbg(indio_dev, "reset");
+
+	return 0;
+}
+
+/**
+ * zpa2326_start_oneshot() - Start a single sampling cycle, i.e. in one shot
+ *                           mode.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Device must have been previously enabled and configured for one shot mode.
+ * Device will be switched back to low power mode at end of cycle.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_start_oneshot(const struct iio_dev *indio_dev)
+{
+	int err;
+
+	err = regmap_write(((struct zpa2326_private *)
+			    iio_priv(indio_dev))->regmap,
+			    ZPA2326_CTRL_REG0_REG,
+			    ZPA2326_CTRL_REG0_ENABLE |
+			    ZPA2326_CTRL_REG0_ONE_SHOT);
+	if (err) {
+		zpa2326_err(indio_dev, "failed to start one shot cycle (%d)",
+			    err);
+		return err;
+	}
+
+	zpa2326_dbg(indio_dev, "one shot cycle started");
+
+	return 0;
+}
+
+/**
+ * zpa2326_power_on() - Power on device to allow subsequent configuration.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @private:   Internal private state related to @indio_dev.
+ *
+ * Sampling will be disabled, preventing strange things from happening in our
+ * back. Hardware FIFO content will be cleared.
+ * When successful, device will be left in the enabled state to allow further
+ * configuration.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_power_on(const struct iio_dev         *indio_dev,
+			    const struct zpa2326_private *private)
+{
+	int err;
+
+	err = regulator_enable(private->vref);
+	if (err)
+		return err;
+
+	err = regulator_enable(private->vdd);
+	if (err)
+		goto vref;
+
+	zpa2326_dbg(indio_dev, "powered on");
+
+	err = zpa2326_enable_device(indio_dev);
+	if (err)
+		goto vdd;
+
+	err = zpa2326_reset_device(indio_dev);
+	if (err)
+		goto sleep;
+
+	return 0;
+
+sleep:
+	zpa2326_sleep(indio_dev);
+vdd:
+	regulator_disable(private->vdd);
+vref:
+	regulator_disable(private->vref);
+
+	zpa2326_dbg(indio_dev, "powered off");
+
+	return err;
+}
+
+/**
+ * zpa2326_power_off() - Power off device, i.e. disable attached power
+ *                       regulators.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @private:   Internal private state related to @indio_dev.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static void zpa2326_power_off(const struct iio_dev         *indio_dev,
+			      const struct zpa2326_private *private)
+{
+	regulator_disable(private->vdd);
+	regulator_disable(private->vref);
+
+	zpa2326_dbg(indio_dev, "powered off");
+}
+
+/**
+ * zpa2326_config_oneshot() - Setup device for one shot / on demand mode.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @irq:       Optional interrupt line the hardware uses to notify new data
+ *             samples are ready. Negative or zero values indicate no interrupts
+ *             are available, meaning polling is required.
+ *
+ * Output Data Rate is configured for the highest possible rate so that
+ * conversion time and power consumption are reduced to a minimum.
+ * Note that hardware internal averaging machinery (not implemented in this
+ * driver) is not applicable in this mode.
+ *
+ * Device must have been previously enabled before calling
+ * zpa2326_config_oneshot().
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_config_oneshot(const struct iio_dev *indio_dev,
+				  int                   irq)
+{
+	struct regmap                  *regs = ((struct zpa2326_private *)
+						iio_priv(indio_dev))->regmap;
+	const struct zpa2326_frequency *freq = zpa2326_highest_frequency();
+	int                             err;
+
+	/* Setup highest available Output Data Rate for one shot mode. */
+	err = regmap_write(regs, ZPA2326_CTRL_REG3_REG, freq->odr);
+	if (err)
+		return err;
+
+	if (irq > 0) {
+		/* Request interrupt when new sample is available. */
+		err = regmap_write(regs, ZPA2326_CTRL_REG1_REG,
+				   (u8)~ZPA2326_CTRL_REG1_MASK_DATA_READY);
+
+		if (err) {
+			dev_err(indio_dev->dev.parent,
+				"failed to setup one shot mode (%d)", err);
+			return err;
+		}
+	}
+
+	zpa2326_dbg(indio_dev, "one shot mode setup @%dHz", freq->hz);
+
+	return 0;
+}
+
+/**
+ * zpa2326_clear_fifo() - Clear remaining entries in hardware FIFO.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @min_count: Number of samples present within hardware FIFO.
+ *
+ * @min_count argument is a hint corresponding to the known minimum number of
+ * samples currently living in the FIFO. This allows to reduce the number of bus
+ * accesses by skipping status register read operation as long as we know for
+ * sure there are still entries left.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_clear_fifo(const struct iio_dev *indio_dev,
+			      unsigned int          min_count)
+{
+	struct regmap *regs = ((struct zpa2326_private *)
+			       iio_priv(indio_dev))->regmap;
+	int            err;
+	unsigned int   val;
+
+	if (!min_count) {
+		/*
+		 * No hint: read status register to determine whether FIFO is
+		 * empty or not.
+		 */
+		err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
+
+		if (err < 0)
+			goto err;
+
+		if (val & ZPA2326_STATUS_FIFO_E)
+			/* Fifo is empty: nothing to trash. */
+			return 0;
+	}
+
+	/* Clear FIFO. */
+	do {
+		/*
+		 * A single fetch from pressure MSB register is enough to pop
+		 * values out of FIFO.
+		 */
+		err = regmap_read(regs, ZPA2326_PRESS_OUT_H_REG, &val);
+		if (err < 0)
+			goto err;
+
+		if (min_count) {
+			/*
+			 * We know for sure there are at least min_count entries
+			 * left in FIFO. Skip status register read.
+			 */
+			min_count--;
+			continue;
+		}
+
+		err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
+		if (err < 0)
+			goto err;
+
+	} while (!(val & ZPA2326_STATUS_FIFO_E));
+
+	zpa2326_dbg(indio_dev, "FIFO cleared");
+
+	return 0;
+
+err:
+	zpa2326_err(indio_dev, "failed to clear FIFO (%d)", err);
+
+	return err;
+}
+
+/**
+ * zpa2326_dequeue_pressure() - Retrieve the most recent pressure sample from
+ *                              hardware FIFO.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @pressure:  Sampled pressure output.
+ *
+ * Note that ZPA2326 hardware FIFO stores pressure samples only.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_dequeue_pressure(const struct iio_dev *indio_dev,
+				    u32                  *pressure)
+{
+	struct regmap *regs = ((struct zpa2326_private *)
+			       iio_priv(indio_dev))->regmap;
+	unsigned int   val;
+	int            err;
+	int            cleared = -1;
+
+	err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
+	if (err < 0)
+		return err;
+
+	*pressure = 0;
+
+	if (val & ZPA2326_STATUS_P_OR) {
+		/*
+		 * Fifo overrun : first sample dequeued from FIFO is the
+		 * newest.
+		 */
+		zpa2326_warn(indio_dev, "FIFO overflow");
+
+		err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure,
+				       3);
+		if (err)
+			return err;
+
+#define ZPA2326_FIFO_DEPTH (16U)
+		/* Hardware FIFO may hold no more than 16 pressure samples. */
+		return zpa2326_clear_fifo(indio_dev, ZPA2326_FIFO_DEPTH - 1);
+	}
+
+	/*
+	 * Fifo has not overflown : retrieve newest sample. We need to pop
+	 * values out until FIFO is empty : last fetched pressure is the newest.
+	 * In nominal cases, we should find a single queued sample only.
+	 */
+	do {
+		err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure,
+				       3);
+		if (err)
+			return err;
+
+		err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
+		if (err < 0)
+			return err;
+
+		cleared++;
+	} while (!(val & ZPA2326_STATUS_FIFO_E));
+
+	if (cleared)
+		/*
+		 * Samples were pushed by hardware during previous rounds but we
+		 * didn't consume them fast enough: inform user.
+		 */
+		zpa2326_dbg(indio_dev, "cleared %d FIFO entries", cleared);
+
+	return 0;
+}
+
+/**
+ * zpa2326_fill_sample_buffer() - Enqueue new channel samples to IIO buffer.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @private:   Internal private state related to @indio_dev.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_fill_sample_buffer(struct iio_dev               *indio_dev,
+				      const struct zpa2326_private *private)
+{
+	struct {
+		u32 pressure;
+		u16 temperature;
+		u64 timestamp;
+	}   sample;
+	int err;
+
+	if (test_bit(0, indio_dev->active_scan_mask)) {
+		/* Get current pressure from hardware FIFO. */
+		err = zpa2326_dequeue_pressure(indio_dev, &sample.pressure);
+		if (err) {
+			zpa2326_warn(indio_dev, "failed to fetch pressure (%d)",
+				     err);
+			return err;
+		}
+	}
+
+	if (test_bit(1, indio_dev->active_scan_mask)) {
+		/* Get current temperature. */
+		err = regmap_bulk_read(private->regmap, ZPA2326_TEMP_OUT_L_REG,
+				       &sample.temperature, 2);
+		if (err) {
+			zpa2326_warn(indio_dev,
+				     "failed to fetch temperature (%d)", err);
+			return err;
+		}
+	}
+
+	/*
+	 * Now push samples using timestamp stored either :
+	 *   - by hardware interrupt handler if interrupt is available: see
+	 *     zpa2326_handle_irq(),
+	 *   - or oneshot completion polling machinery : see
+	 *     zpa2326_trigger_handler().
+	 */
+	zpa2326_dbg(indio_dev, "filling raw samples buffer");
+
+	iio_push_to_buffers_with_timestamp(indio_dev, &sample,
+					   private->timestamp);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int zpa2326_runtime_suspend(struct device *parent)
+{
+	const struct iio_dev *indio_dev = dev_get_drvdata(parent);
+
+	if (pm_runtime_autosuspend_expiration(parent))
+		/* Userspace changed autosuspend delay. */
+		return -EAGAIN;
+
+	zpa2326_power_off(indio_dev, iio_priv(indio_dev));
+
+	return 0;
+}
+
+static int zpa2326_runtime_resume(struct device *parent)
+{
+	const struct iio_dev *indio_dev = dev_get_drvdata(parent);
+
+	return zpa2326_power_on(indio_dev, iio_priv(indio_dev));
+}
+
+const struct dev_pm_ops zpa2326_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(zpa2326_runtime_suspend, zpa2326_runtime_resume,
+			   NULL)
+};
+EXPORT_SYMBOL_NS_GPL(zpa2326_pm_ops, IIO_ZPA2326);
+
+/**
+ * zpa2326_resume() - Request the PM layer to power supply the device.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Return:
+ *  < 0 - a negative error code meaning failure ;
+ *    0 - success, device has just been powered up ;
+ *    1 - success, device was already powered.
+ */
+static int zpa2326_resume(const struct iio_dev *indio_dev)
+{
+	int err;
+
+	err = pm_runtime_get_sync(indio_dev->dev.parent);
+	if (err < 0) {
+		pm_runtime_put(indio_dev->dev.parent);
+		return err;
+	}
+
+	if (err > 0) {
+		/*
+		 * Device was already power supplied: get it out of low power
+		 * mode and inform caller.
+		 */
+		zpa2326_enable_device(indio_dev);
+		return 1;
+	}
+
+	/* Inform caller device has just been brought back to life. */
+	return 0;
+}
+
+/**
+ * zpa2326_suspend() - Schedule a power down using autosuspend feature of PM
+ *                     layer.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Device is switched to low power mode at first to save power even when
+ * attached regulator is a "dummy" one.
+ */
+static void zpa2326_suspend(struct iio_dev *indio_dev)
+{
+	struct device *parent = indio_dev->dev.parent;
+
+	zpa2326_sleep(indio_dev);
+
+	pm_runtime_mark_last_busy(parent);
+	pm_runtime_put_autosuspend(parent);
+}
+
+static void zpa2326_init_runtime(struct device *parent)
+{
+	pm_runtime_get_noresume(parent);
+	pm_runtime_set_active(parent);
+	pm_runtime_enable(parent);
+	pm_runtime_set_autosuspend_delay(parent, 1000);
+	pm_runtime_use_autosuspend(parent);
+	pm_runtime_mark_last_busy(parent);
+	pm_runtime_put_autosuspend(parent);
+}
+
+static void zpa2326_fini_runtime(struct device *parent)
+{
+	pm_runtime_disable(parent);
+	pm_runtime_set_suspended(parent);
+}
+#else /* !CONFIG_PM */
+static int zpa2326_resume(const struct iio_dev *indio_dev)
+{
+	zpa2326_enable_device(indio_dev);
+
+	return 0;
+}
+
+static void zpa2326_suspend(struct iio_dev *indio_dev)
+{
+	zpa2326_sleep(indio_dev);
+}
+
+#define zpa2326_init_runtime(_parent)
+#define zpa2326_fini_runtime(_parent)
+#endif /* !CONFIG_PM */
+
+/**
+ * zpa2326_handle_irq() - Process hardware interrupts.
+ * @irq:  Interrupt line the hardware uses to notify new data has arrived.
+ * @data: The IIO device associated with the sampling hardware.
+ *
+ * Timestamp buffered samples as soon as possible then schedule threaded bottom
+ * half.
+ *
+ * Return: Always successful.
+ */
+static irqreturn_t zpa2326_handle_irq(int irq, void *data)
+{
+	struct iio_dev *indio_dev = data;
+
+	if (iio_buffer_enabled(indio_dev)) {
+		/* Timestamping needed for buffered sampling only. */
+		((struct zpa2326_private *)
+		 iio_priv(indio_dev))->timestamp = iio_get_time_ns(indio_dev);
+	}
+
+	return IRQ_WAKE_THREAD;
+}
+
+/**
+ * zpa2326_handle_threaded_irq() - Interrupt bottom-half handler.
+ * @irq:  Interrupt line the hardware uses to notify new data has arrived.
+ * @data: The IIO device associated with the sampling hardware.
+ *
+ * Mainly ensures interrupt is caused by a real "new sample available"
+ * condition. This relies upon the ability to perform blocking / sleeping bus
+ * accesses to slave's registers. This is why zpa2326_handle_threaded_irq() is
+ * called from within a thread, i.e. not called from hard interrupt context.
+ *
+ * When device is using its own internal hardware trigger in continuous sampling
+ * mode, data are available into hardware FIFO once interrupt has occurred. All
+ * we have to do is to dispatch the trigger, which in turn will fetch data and
+ * fill IIO buffer.
+ *
+ * When not using its own internal hardware trigger, the device has been
+ * configured in one-shot mode either by an external trigger or the IIO read_raw
+ * hook. This means one of the latter is currently waiting for sampling
+ * completion, in which case we must simply wake it up.
+ *
+ * See zpa2326_trigger_handler().
+ *
+ * Return:
+ *   %IRQ_NONE - no consistent interrupt happened ;
+ *   %IRQ_HANDLED - there was new samples available.
+ */
+static irqreturn_t zpa2326_handle_threaded_irq(int irq, void *data)
+{
+	struct iio_dev         *indio_dev = data;
+	struct zpa2326_private *priv = iio_priv(indio_dev);
+	unsigned int            val;
+	bool                    cont;
+	irqreturn_t             ret = IRQ_NONE;
+
+	/*
+	 * Are we using our own internal trigger in triggered buffer mode, i.e.,
+	 * currently working in continuous sampling mode ?
+	 */
+	cont = (iio_buffer_enabled(indio_dev) &&
+		iio_trigger_using_own(indio_dev));
+
+	/*
+	 * Device works according to a level interrupt scheme: reading interrupt
+	 * status de-asserts interrupt line.
+	 */
+	priv->result = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val);
+	if (priv->result < 0) {
+		if (cont)
+			return IRQ_NONE;
+
+		goto complete;
+	}
+
+	/* Data ready is the only interrupt source we requested. */
+	if (!(val & ZPA2326_INT_SOURCE_DATA_READY)) {
+		/*
+		 * Interrupt happened but no new sample available: likely caused
+		 * by spurious interrupts, in which case, returning IRQ_NONE
+		 * allows to benefit from the generic spurious interrupts
+		 * handling.
+		 */
+		zpa2326_warn(indio_dev, "unexpected interrupt status %02x",
+			     val);
+
+		if (cont)
+			return IRQ_NONE;
+
+		priv->result = -ENODATA;
+		goto complete;
+	}
+
+	/* New sample available: dispatch internal trigger consumers. */
+	iio_trigger_poll_chained(priv->trigger);
+
+	if (cont)
+		/*
+		 * Internal hardware trigger has been scheduled above : it will
+		 * fetch data on its own.
+		 */
+		return IRQ_HANDLED;
+
+	ret = IRQ_HANDLED;
+
+complete:
+	/*
+	 * Wake up direct or externaly triggered buffer mode waiters: see
+	 * zpa2326_sample_oneshot() and zpa2326_trigger_handler().
+	 */
+	complete(&priv->data_ready);
+
+	return ret;
+}
+
+/**
+ * zpa2326_wait_oneshot_completion() - Wait for oneshot data ready interrupt.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @private:   Internal private state related to @indio_dev.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_wait_oneshot_completion(const struct iio_dev   *indio_dev,
+					   struct zpa2326_private *private)
+{
+	unsigned int val;
+	long     timeout;
+
+	zpa2326_dbg(indio_dev, "waiting for one shot completion interrupt");
+
+	timeout = wait_for_completion_interruptible_timeout(
+		&private->data_ready, ZPA2326_CONVERSION_JIFFIES);
+	if (timeout > 0)
+		/*
+		 * Interrupt handler completed before timeout: return operation
+		 * status.
+		 */
+		return private->result;
+
+	/* Clear all interrupts just to be sure. */
+	regmap_read(private->regmap, ZPA2326_INT_SOURCE_REG, &val);
+
+	if (!timeout) {
+		/* Timed out. */
+		zpa2326_warn(indio_dev, "no one shot interrupt occurred (%ld)",
+			     timeout);
+		return -ETIME;
+	}
+
+	zpa2326_warn(indio_dev, "wait for one shot interrupt cancelled");
+	return -ERESTARTSYS;
+}
+
+static int zpa2326_init_managed_irq(struct device          *parent,
+				    struct iio_dev         *indio_dev,
+				    struct zpa2326_private *private,
+				    int                     irq)
+{
+	int err;
+
+	private->irq = irq;
+
+	if (irq <= 0) {
+		/*
+		 * Platform declared no interrupt line: device will be polled
+		 * for data availability.
+		 */
+		dev_info(parent, "no interrupt found, running in polling mode");
+		return 0;
+	}
+
+	init_completion(&private->data_ready);
+
+	/* Request handler to be scheduled into threaded interrupt context. */
+	err = devm_request_threaded_irq(parent, irq, zpa2326_handle_irq,
+					zpa2326_handle_threaded_irq,
+					IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+					dev_name(parent), indio_dev);
+	if (err) {
+		dev_err(parent, "failed to request interrupt %d (%d)", irq,
+			err);
+		return err;
+	}
+
+	dev_info(parent, "using interrupt %d", irq);
+
+	return 0;
+}
+
+/**
+ * zpa2326_poll_oneshot_completion() - Actively poll for one shot data ready.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Loop over registers content to detect end of sampling cycle. Used when DT
+ * declared no valid interrupt lines.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_poll_oneshot_completion(const struct iio_dev *indio_dev)
+{
+	unsigned long  tmout = jiffies + ZPA2326_CONVERSION_JIFFIES;
+	struct regmap *regs = ((struct zpa2326_private *)
+			       iio_priv(indio_dev))->regmap;
+	unsigned int   val;
+	int            err;
+
+	zpa2326_dbg(indio_dev, "polling for one shot completion");
+
+	/*
+	 * At least, 100 ms is needed for the device to complete its one-shot
+	 * cycle.
+	 */
+	if (msleep_interruptible(100))
+		return -ERESTARTSYS;
+
+	/* Poll for conversion completion in hardware. */
+	while (true) {
+		err = regmap_read(regs, ZPA2326_CTRL_REG0_REG, &val);
+		if (err < 0)
+			goto err;
+
+		if (!(val & ZPA2326_CTRL_REG0_ONE_SHOT))
+			/* One-shot bit self clears at conversion end. */
+			break;
+
+		if (time_after(jiffies, tmout)) {
+			/* Prevent from waiting forever : let's time out. */
+			err = -ETIME;
+			goto err;
+		}
+
+		usleep_range(10000, 20000);
+	}
+
+	/*
+	 * In oneshot mode, pressure sample availability guarantees that
+	 * temperature conversion has also completed : just check pressure
+	 * status bit to keep things simple.
+	 */
+	err = regmap_read(regs, ZPA2326_STATUS_REG, &val);
+	if (err < 0)
+		goto err;
+
+	if (!(val & ZPA2326_STATUS_P_DA)) {
+		/* No sample available. */
+		err = -ENODATA;
+		goto err;
+	}
+
+	return 0;
+
+err:
+	zpa2326_warn(indio_dev, "failed to poll one shot completion (%d)", err);
+
+	return err;
+}
+
+/**
+ * zpa2326_fetch_raw_sample() - Retrieve a raw sample and convert it to CPU
+ *                              endianness.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @type:      Type of measurement / channel to fetch from.
+ * @value:     Sample output.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_fetch_raw_sample(const struct iio_dev *indio_dev,
+				    enum iio_chan_type    type,
+				    int                  *value)
+{
+	struct regmap *regs = ((struct zpa2326_private *)
+			       iio_priv(indio_dev))->regmap;
+	int            err;
+	u8             v[3];
+
+	switch (type) {
+	case IIO_PRESSURE:
+		zpa2326_dbg(indio_dev, "fetching raw pressure sample");
+
+		err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, v, sizeof(v));
+		if (err) {
+			zpa2326_warn(indio_dev, "failed to fetch pressure (%d)",
+				     err);
+			return err;
+		}
+
+		*value = get_unaligned_le24(&v[0]);
+
+		return IIO_VAL_INT;
+
+	case IIO_TEMP:
+		zpa2326_dbg(indio_dev, "fetching raw temperature sample");
+
+		err = regmap_bulk_read(regs, ZPA2326_TEMP_OUT_L_REG, value, 2);
+		if (err) {
+			zpa2326_warn(indio_dev,
+				     "failed to fetch temperature (%d)", err);
+			return err;
+		}
+
+		/* Temperature is a 16 bits wide little-endian signed int. */
+		*value = (int)le16_to_cpup((__le16 *)value);
+
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+/**
+ * zpa2326_sample_oneshot() - Perform a complete one shot sampling cycle.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @type:      Type of measurement / channel to fetch from.
+ * @value:     Sample output.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_sample_oneshot(struct iio_dev     *indio_dev,
+				  enum iio_chan_type  type,
+				  int                *value)
+{
+	int                     ret;
+	struct zpa2326_private *priv;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = zpa2326_resume(indio_dev);
+	if (ret < 0)
+		goto release;
+
+	priv = iio_priv(indio_dev);
+
+	if (ret > 0) {
+		/*
+		 * We were already power supplied. Just clear hardware FIFO to
+		 * get rid of samples acquired during previous rounds (if any).
+		 * Sampling operation always generates both temperature and
+		 * pressure samples. The latter are always enqueued into
+		 * hardware FIFO. This may lead to situations were pressure
+		 * samples still sit into FIFO when previous cycle(s) fetched
+		 * temperature data only.
+		 * Hence, we need to clear hardware FIFO content to prevent from
+		 * getting outdated values at the end of current cycle.
+		 */
+		if (type == IIO_PRESSURE) {
+			ret = zpa2326_clear_fifo(indio_dev, 0);
+			if (ret)
+				goto suspend;
+		}
+	} else {
+		/*
+		 * We have just been power supplied, i.e. device is in default
+		 * "out of reset" state, meaning we need to reconfigure it
+		 * entirely.
+		 */
+		ret = zpa2326_config_oneshot(indio_dev, priv->irq);
+		if (ret)
+			goto suspend;
+	}
+
+	/* Start a sampling cycle in oneshot mode. */
+	ret = zpa2326_start_oneshot(indio_dev);
+	if (ret)
+		goto suspend;
+
+	/* Wait for sampling cycle to complete. */
+	if (priv->irq > 0)
+		ret = zpa2326_wait_oneshot_completion(indio_dev, priv);
+	else
+		ret = zpa2326_poll_oneshot_completion(indio_dev);
+
+	if (ret)
+		goto suspend;
+
+	/* Retrieve raw sample value and convert it to CPU endianness. */
+	ret = zpa2326_fetch_raw_sample(indio_dev, type, value);
+
+suspend:
+	zpa2326_suspend(indio_dev);
+release:
+	iio_device_release_direct_mode(indio_dev);
+
+	return ret;
+}
+
+/**
+ * zpa2326_trigger_handler() - Perform an IIO buffered sampling round in one
+ *                             shot mode.
+ * @irq:  The software interrupt assigned to @data
+ * @data: The IIO poll function dispatched by external trigger our device is
+ *        attached to.
+ *
+ * Bottom-half handler called by the IIO trigger to which our device is
+ * currently attached. Allows us to synchronize this device buffered sampling
+ * either with external events (such as timer expiration, external device sample
+ * ready, etc...) or with its own interrupt (internal hardware trigger).
+ *
+ * When using an external trigger, basically run the same sequence of operations
+ * as for zpa2326_sample_oneshot() with the following hereafter. Hardware FIFO
+ * is not cleared since already done at buffering enable time and samples
+ * dequeueing always retrieves the most recent value.
+ *
+ * Otherwise, when internal hardware trigger has dispatched us, just fetch data
+ * from hardware FIFO.
+ *
+ * Fetched data will pushed unprocessed to IIO buffer since samples conversion
+ * is delegated to userspace in buffered mode (endianness, etc...).
+ *
+ * Return:
+ *   %IRQ_NONE - no consistent interrupt happened ;
+ *   %IRQ_HANDLED - there was new samples available.
+ */
+static irqreturn_t zpa2326_trigger_handler(int irq, void *data)
+{
+	struct iio_dev         *indio_dev = ((struct iio_poll_func *)
+					     data)->indio_dev;
+	struct zpa2326_private *priv = iio_priv(indio_dev);
+	bool                    cont;
+
+	/*
+	 * We have been dispatched, meaning we are in triggered buffer mode.
+	 * Using our own internal trigger implies we are currently in continuous
+	 * hardware sampling mode.
+	 */
+	cont = iio_trigger_using_own(indio_dev);
+
+	if (!cont) {
+		/* On demand sampling : start a one shot cycle. */
+		if (zpa2326_start_oneshot(indio_dev))
+			goto out;
+
+		/* Wait for sampling cycle to complete. */
+		if (priv->irq <= 0) {
+			/* No interrupt available: poll for completion. */
+			if (zpa2326_poll_oneshot_completion(indio_dev))
+				goto out;
+
+			/* Only timestamp sample once it is ready. */
+			priv->timestamp = iio_get_time_ns(indio_dev);
+		} else {
+			/* Interrupt handlers will timestamp for us. */
+			if (zpa2326_wait_oneshot_completion(indio_dev, priv))
+				goto out;
+		}
+	}
+
+	/* Enqueue to IIO buffer / userspace. */
+	zpa2326_fill_sample_buffer(indio_dev, priv);
+
+out:
+	if (!cont)
+		/* Don't switch to low power if sampling continuously. */
+		zpa2326_sleep(indio_dev);
+
+	/* Inform attached trigger we are done. */
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * zpa2326_preenable_buffer() - Prepare device for configuring triggered
+ *                              sampling
+ * modes.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Basically power up device.
+ * Called with IIO device's lock held.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_preenable_buffer(struct iio_dev *indio_dev)
+{
+	int ret = zpa2326_resume(indio_dev);
+
+	if (ret < 0)
+		return ret;
+
+	/* Tell zpa2326_postenable_buffer() if we have just been powered on. */
+	((struct zpa2326_private *)
+	 iio_priv(indio_dev))->waken = iio_priv(indio_dev);
+
+	return 0;
+}
+
+/**
+ * zpa2326_postenable_buffer() - Configure device for triggered sampling.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ *
+ * Basically setup one-shot mode if plugging external trigger.
+ * Otherwise, let internal trigger configure continuous sampling :
+ * see zpa2326_set_trigger_state().
+ *
+ * If an error is returned, IIO layer will call our postdisable hook for us,
+ * i.e. no need to explicitly power device off here.
+ * Called with IIO device's lock held.
+ *
+ * Called with IIO device's lock held.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_postenable_buffer(struct iio_dev *indio_dev)
+{
+	const struct zpa2326_private *priv = iio_priv(indio_dev);
+	int                           err;
+
+	if (!priv->waken) {
+		/*
+		 * We were already power supplied. Just clear hardware FIFO to
+		 * get rid of samples acquired during previous rounds (if any).
+		 */
+		err = zpa2326_clear_fifo(indio_dev, 0);
+		if (err) {
+			zpa2326_err(indio_dev,
+				    "failed to enable buffering (%d)", err);
+			return err;
+		}
+	}
+
+	if (!iio_trigger_using_own(indio_dev) && priv->waken) {
+		/*
+		 * We are using an external trigger and we have just been
+		 * powered up: reconfigure one-shot mode.
+		 */
+		err = zpa2326_config_oneshot(indio_dev, priv->irq);
+		if (err) {
+			zpa2326_err(indio_dev,
+				    "failed to enable buffering (%d)", err);
+			return err;
+		}
+	}
+
+	return 0;
+}
+
+static int zpa2326_postdisable_buffer(struct iio_dev *indio_dev)
+{
+	zpa2326_suspend(indio_dev);
+
+	return 0;
+}
+
+static const struct iio_buffer_setup_ops zpa2326_buffer_setup_ops = {
+	.preenable   = zpa2326_preenable_buffer,
+	.postenable  = zpa2326_postenable_buffer,
+	.postdisable = zpa2326_postdisable_buffer
+};
+
+/**
+ * zpa2326_set_trigger_state() - Start / stop continuous sampling.
+ * @trig:  The trigger being attached to IIO device associated with the sampling
+ *         hardware.
+ * @state: Tell whether to start (true) or stop (false)
+ *
+ * Basically enable / disable hardware continuous sampling mode.
+ *
+ * Called with IIO device's lock held at postenable() or predisable() time.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_set_trigger_state(struct iio_trigger *trig, bool state)
+{
+	const struct iio_dev         *indio_dev = dev_get_drvdata(
+							trig->dev.parent);
+	const struct zpa2326_private *priv = iio_priv(indio_dev);
+	int                           err;
+
+	if (!state) {
+		/*
+		 * Switch trigger off : in case of failure, interrupt is left
+		 * disabled in order to prevent handler from accessing released
+		 * resources.
+		 */
+		unsigned int val;
+
+		/*
+		 * As device is working in continuous mode, handlers may be
+		 * accessing resources we are currently freeing...
+		 * Prevent this by disabling interrupt handlers and ensure
+		 * the device will generate no more interrupts unless explicitly
+		 * required to, i.e. by restoring back to default one shot mode.
+		 */
+		disable_irq(priv->irq);
+
+		/*
+		 * Disable continuous sampling mode to restore settings for
+		 * one shot / direct sampling operations.
+		 */
+		err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG,
+				   zpa2326_highest_frequency()->odr);
+		if (err)
+			return err;
+
+		/*
+		 * Now that device won't generate interrupts on its own,
+		 * acknowledge any currently active interrupts (may happen on
+		 * rare occasions while stopping continuous mode).
+		 */
+		err = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val);
+		if (err < 0)
+			return err;
+
+		/*
+		 * Re-enable interrupts only if we can guarantee the device will
+		 * generate no more interrupts to prevent handlers from
+		 * accessing released resources.
+		 */
+		enable_irq(priv->irq);
+
+		zpa2326_dbg(indio_dev, "continuous mode stopped");
+	} else {
+		/*
+		 * Switch trigger on : start continuous sampling at required
+		 * frequency.
+		 */
+
+		if (priv->waken) {
+			/* Enable interrupt if getting out of reset. */
+			err = regmap_write(priv->regmap, ZPA2326_CTRL_REG1_REG,
+					   (u8)
+					   ~ZPA2326_CTRL_REG1_MASK_DATA_READY);
+			if (err)
+				return err;
+		}
+
+		/* Enable continuous sampling at specified frequency. */
+		err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG,
+				   ZPA2326_CTRL_REG3_ENABLE_MEAS |
+				   priv->frequency->odr);
+		if (err)
+			return err;
+
+		zpa2326_dbg(indio_dev, "continuous mode setup @%dHz",
+			    priv->frequency->hz);
+	}
+
+	return 0;
+}
+
+static const struct iio_trigger_ops zpa2326_trigger_ops = {
+	.set_trigger_state = zpa2326_set_trigger_state,
+};
+
+/**
+ * zpa2326_init_managed_trigger() - Create interrupt driven / hardware trigger
+ *                          allowing to notify external devices a new sample is
+ *                          ready.
+ * @parent:    Hardware sampling device @indio_dev is a child of.
+ * @indio_dev: The IIO device associated with the sampling hardware.
+ * @private:   Internal private state related to @indio_dev.
+ * @irq:       Optional interrupt line the hardware uses to notify new data
+ *             samples are ready. Negative or zero values indicate no interrupts
+ *             are available, meaning polling is required.
+ *
+ * Only relevant when DT declares a valid interrupt line.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+static int zpa2326_init_managed_trigger(struct device          *parent,
+					struct iio_dev         *indio_dev,
+					struct zpa2326_private *private,
+					int                     irq)
+{
+	struct iio_trigger *trigger;
+	int                 ret;
+
+	if (irq <= 0)
+		return 0;
+
+	trigger = devm_iio_trigger_alloc(parent, "%s-dev%d",
+					 indio_dev->name,
+					 iio_device_id(indio_dev));
+	if (!trigger)
+		return -ENOMEM;
+
+	/* Basic setup. */
+	trigger->ops = &zpa2326_trigger_ops;
+
+	private->trigger = trigger;
+
+	/* Register to triggers space. */
+	ret = devm_iio_trigger_register(parent, trigger);
+	if (ret)
+		dev_err(parent, "failed to register hardware trigger (%d)",
+			ret);
+
+	return ret;
+}
+
+static int zpa2326_get_frequency(const struct iio_dev *indio_dev)
+{
+	return ((struct zpa2326_private *)iio_priv(indio_dev))->frequency->hz;
+}
+
+static int zpa2326_set_frequency(struct iio_dev *indio_dev, int hz)
+{
+	struct zpa2326_private *priv = iio_priv(indio_dev);
+	int                     freq;
+	int                     err;
+
+	/* Check if requested frequency is supported. */
+	for (freq = 0; freq < ARRAY_SIZE(zpa2326_sampling_frequencies); freq++)
+		if (zpa2326_sampling_frequencies[freq].hz == hz)
+			break;
+	if (freq == ARRAY_SIZE(zpa2326_sampling_frequencies))
+		return -EINVAL;
+
+	/* Don't allow changing frequency if buffered sampling is ongoing. */
+	err = iio_device_claim_direct_mode(indio_dev);
+	if (err)
+		return err;
+
+	priv->frequency = &zpa2326_sampling_frequencies[freq];
+
+	iio_device_release_direct_mode(indio_dev);
+
+	return 0;
+}
+
+/* Expose supported hardware sampling frequencies (Hz) through sysfs. */
+static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("1 5 11 23");
+
+static struct attribute *zpa2326_attributes[] = {
+	&iio_const_attr_sampling_frequency_available.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group zpa2326_attribute_group = {
+	.attrs = zpa2326_attributes,
+};
+
+static int zpa2326_read_raw(struct iio_dev             *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int                        *val,
+			    int                        *val2,
+			    long                        mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		return zpa2326_sample_oneshot(indio_dev, chan->type, val);
+
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_PRESSURE:
+			/*
+			 * Pressure resolution is 1/64 Pascal. Scale to kPascal
+			 * as required by IIO ABI.
+			 */
+			*val = 1;
+			*val2 = 64000;
+			return IIO_VAL_FRACTIONAL;
+
+		case IIO_TEMP:
+			/*
+			 * Temperature follows the equation:
+			 *     Temp[degC] = Tempcode * 0.00649 - 176.83
+			 * where:
+			 *     Tempcode is composed the raw sampled 16 bits.
+			 *
+			 * Hence, to produce a temperature in milli-degrees
+			 * Celsius according to IIO ABI, we need to apply the
+			 * following equation to raw samples:
+			 *     Temp[milli degC] = (Tempcode + Offset) * Scale
+			 * where:
+			 *     Offset = -176.83 / 0.00649
+			 *     Scale = 0.00649 * 1000
+			 */
+			*val = 6;
+			*val2 = 490000;
+			return IIO_VAL_INT_PLUS_MICRO;
+
+		default:
+			return -EINVAL;
+		}
+
+	case IIO_CHAN_INFO_OFFSET:
+		switch (chan->type) {
+		case IIO_TEMP:
+			*val = -17683000;
+			*val2 = 649;
+			return IIO_VAL_FRACTIONAL;
+
+		default:
+			return -EINVAL;
+		}
+
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = zpa2326_get_frequency(indio_dev);
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static int zpa2326_write_raw(struct iio_dev             *indio_dev,
+			     const struct iio_chan_spec *chan,
+			     int                         val,
+			     int                         val2,
+			     long                        mask)
+{
+	if ((mask != IIO_CHAN_INFO_SAMP_FREQ) || val2)
+		return -EINVAL;
+
+	return zpa2326_set_frequency(indio_dev, val);
+}
+
+static const struct iio_chan_spec zpa2326_channels[] = {
+	[0] = {
+		.type                    = IIO_PRESSURE,
+		.scan_index              = 0,
+		.scan_type               = {
+			.sign                   = 'u',
+			.realbits               = 24,
+			.storagebits            = 32,
+			.endianness             = IIO_LE,
+		},
+		.info_mask_separate      = BIT(IIO_CHAN_INFO_RAW) |
+					   BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	[1] = {
+		.type                    = IIO_TEMP,
+		.scan_index              = 1,
+		.scan_type               = {
+			.sign                   = 's',
+			.realbits               = 16,
+			.storagebits            = 16,
+			.endianness             = IIO_LE,
+		},
+		.info_mask_separate      = BIT(IIO_CHAN_INFO_RAW) |
+					   BIT(IIO_CHAN_INFO_SCALE) |
+					   BIT(IIO_CHAN_INFO_OFFSET),
+		.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	},
+	[2] = IIO_CHAN_SOFT_TIMESTAMP(2),
+};
+
+static const struct iio_info zpa2326_info = {
+	.attrs         = &zpa2326_attribute_group,
+	.read_raw      = zpa2326_read_raw,
+	.write_raw     = zpa2326_write_raw,
+};
+
+static struct iio_dev *zpa2326_create_managed_iiodev(struct device *device,
+						     const char    *name,
+						     struct regmap *regmap)
+{
+	struct iio_dev *indio_dev;
+
+	/* Allocate space to hold IIO device internal state. */
+	indio_dev = devm_iio_device_alloc(device,
+					  sizeof(struct zpa2326_private));
+	if (!indio_dev)
+		return NULL;
+
+	/* Setup for userspace synchronous on demand sampling. */
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = zpa2326_channels;
+	indio_dev->num_channels = ARRAY_SIZE(zpa2326_channels);
+	indio_dev->name = name;
+	indio_dev->info = &zpa2326_info;
+
+	return indio_dev;
+}
+
+int zpa2326_probe(struct device *parent,
+		  const char    *name,
+		  int            irq,
+		  unsigned int   hwid,
+		  struct regmap *regmap)
+{
+	struct iio_dev         *indio_dev;
+	struct zpa2326_private *priv;
+	int                     err;
+	unsigned int            id;
+
+	indio_dev = zpa2326_create_managed_iiodev(parent, name, regmap);
+	if (!indio_dev)
+		return -ENOMEM;
+
+	priv = iio_priv(indio_dev);
+
+	priv->vref = devm_regulator_get(parent, "vref");
+	if (IS_ERR(priv->vref))
+		return PTR_ERR(priv->vref);
+
+	priv->vdd = devm_regulator_get(parent, "vdd");
+	if (IS_ERR(priv->vdd))
+		return PTR_ERR(priv->vdd);
+
+	/* Set default hardware sampling frequency to highest rate supported. */
+	priv->frequency = zpa2326_highest_frequency();
+
+	/*
+	 * Plug device's underlying bus abstraction : this MUST be set before
+	 * registering interrupt handlers since an interrupt might happen if
+	 * power up sequence is not properly applied.
+	 */
+	priv->regmap = regmap;
+
+	err = devm_iio_triggered_buffer_setup(parent, indio_dev, NULL,
+					      zpa2326_trigger_handler,
+					      &zpa2326_buffer_setup_ops);
+	if (err)
+		return err;
+
+	err = zpa2326_init_managed_trigger(parent, indio_dev, priv, irq);
+	if (err)
+		return err;
+
+	err = zpa2326_init_managed_irq(parent, indio_dev, priv, irq);
+	if (err)
+		return err;
+
+	/* Power up to check device ID and perform initial hardware setup. */
+	err = zpa2326_power_on(indio_dev, priv);
+	if (err)
+		return err;
+
+	/* Read id register to check we are talking to the right slave. */
+	err = regmap_read(regmap, ZPA2326_DEVICE_ID_REG, &id);
+	if (err)
+		goto sleep;
+
+	if (id != hwid) {
+		dev_err(parent, "found device with unexpected id %02x", id);
+		err = -ENODEV;
+		goto sleep;
+	}
+
+	err = zpa2326_config_oneshot(indio_dev, irq);
+	if (err)
+		goto sleep;
+
+	/* Setup done : go sleeping. Device will be awaken upon user request. */
+	err = zpa2326_sleep(indio_dev);
+	if (err)
+		goto poweroff;
+
+	dev_set_drvdata(parent, indio_dev);
+
+	zpa2326_init_runtime(parent);
+
+	err = iio_device_register(indio_dev);
+	if (err) {
+		zpa2326_fini_runtime(parent);
+		goto poweroff;
+	}
+
+	return 0;
+
+sleep:
+	/* Put to sleep just in case power regulators are "dummy" ones. */
+	zpa2326_sleep(indio_dev);
+poweroff:
+	zpa2326_power_off(indio_dev, priv);
+
+	return err;
+}
+EXPORT_SYMBOL_NS_GPL(zpa2326_probe, IIO_ZPA2326);
+
+void zpa2326_remove(const struct device *parent)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(parent);
+
+	iio_device_unregister(indio_dev);
+	zpa2326_fini_runtime(indio_dev->dev.parent);
+	zpa2326_sleep(indio_dev);
+	zpa2326_power_off(indio_dev, iio_priv(indio_dev));
+}
+EXPORT_SYMBOL_NS_GPL(zpa2326_remove, IIO_ZPA2326);
+
+MODULE_AUTHOR("Gregor Boirie <gregor.boirie@parrot.com>");
+MODULE_DESCRIPTION("Core driver for Murata ZPA2326 pressure sensor");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/pressure/zpa2326.h b/drivers/iio/pressure/zpa2326.h
new file mode 100644
index 000000000..45bd79009
--- /dev/null
+++ b/drivers/iio/pressure/zpa2326.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Murata ZPA2326 pressure and temperature sensor IIO driver
+ *
+ * Copyright (c) 2016 Parrot S.A.
+ *
+ * Author: Gregor Boirie <gregor.boirie@parrot.com>
+ */
+
+#ifndef _ZPA2326_H
+#define _ZPA2326_H
+
+/* Register map. */
+#define ZPA2326_REF_P_XL_REG              (0x8)
+#define ZPA2326_REF_P_L_REG               (0x9)
+#define ZPA2326_REF_P_H_REG               (0xa)
+#define ZPA2326_DEVICE_ID_REG             (0xf)
+#define ZPA2326_DEVICE_ID                 (0xb9)
+#define ZPA2326_RES_CONF_REG              (0x10)
+#define ZPA2326_CTRL_REG0_REG             (0x20)
+#define ZPA2326_CTRL_REG0_ONE_SHOT        BIT(0)
+#define ZPA2326_CTRL_REG0_ENABLE          BIT(1)
+#define ZPA2326_CTRL_REG1_REG             (0x21)
+#define ZPA2326_CTRL_REG1_MASK_DATA_READY BIT(2)
+#define ZPA2326_CTRL_REG2_REG             (0x22)
+#define ZPA2326_CTRL_REG2_SWRESET         BIT(2)
+#define ZPA2326_CTRL_REG3_REG             (0x23)
+#define ZPA2326_CTRL_REG3_ODR_SHIFT       (4)
+#define ZPA2326_CTRL_REG3_ENABLE_MEAS     BIT(7)
+#define ZPA2326_INT_SOURCE_REG            (0x24)
+#define ZPA2326_INT_SOURCE_DATA_READY     BIT(2)
+#define ZPA2326_THS_P_LOW_REG             (0x25)
+#define ZPA2326_THS_P_HIGH_REG            (0x26)
+#define ZPA2326_STATUS_REG                (0x27)
+#define ZPA2326_STATUS_P_DA               BIT(1)
+#define ZPA2326_STATUS_FIFO_E             BIT(2)
+#define ZPA2326_STATUS_P_OR               BIT(5)
+#define ZPA2326_PRESS_OUT_XL_REG          (0x28)
+#define ZPA2326_PRESS_OUT_L_REG           (0x29)
+#define ZPA2326_PRESS_OUT_H_REG           (0x2a)
+#define ZPA2326_TEMP_OUT_L_REG            (0x2b)
+#define ZPA2326_TEMP_OUT_H_REG            (0x2c)
+
+struct device;
+struct regmap;
+
+bool zpa2326_isreg_writeable(struct device *dev, unsigned int reg);
+bool zpa2326_isreg_readable(struct device *dev, unsigned int reg);
+bool zpa2326_isreg_precious(struct device *dev, unsigned int reg);
+
+/**
+ * zpa2326_probe() - Instantiate and register core ZPA2326 IIO device
+ * @parent: Hardware sampling device the created IIO device will be a child of.
+ * @name:   Arbitrary name to identify the device.
+ * @irq:    Interrupt line, negative if none.
+ * @hwid:   Expected device hardware id.
+ * @regmap: Registers map used to abstract underlying bus accesses.
+ *
+ * Return: Zero when successful, a negative error code otherwise.
+ */
+int zpa2326_probe(struct device        *parent,
+		  const char           *name,
+		  int                   irq,
+		  unsigned int          hwid,
+		  struct regmap        *regmap);
+
+/**
+ * zpa2326_remove() - Unregister and destroy core ZPA2326 IIO device.
+ * @parent: Hardware sampling device the IIO device to remove is a child of.
+ */
+void zpa2326_remove(const struct device *parent);
+
+#ifdef CONFIG_PM
+#include <linux/pm.h>
+extern const struct dev_pm_ops zpa2326_pm_ops;
+#define ZPA2326_PM_OPS (&zpa2326_pm_ops)
+#else
+#define ZPA2326_PM_OPS (NULL)
+#endif
+
+#endif
diff --git a/drivers/iio/pressure/zpa2326_i2c.c b/drivers/iio/pressure/zpa2326_i2c.c
new file mode 100644
index 000000000..f26dd8cbb
--- /dev/null
+++ b/drivers/iio/pressure/zpa2326_i2c.c
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Murata ZPA2326 I2C pressure and temperature sensor driver
+ *
+ * Copyright (c) 2016 Parrot S.A.
+ *
+ * Author: Gregor Boirie <gregor.boirie@parrot.com>
+ */
+
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include "zpa2326.h"
+
+/*
+ * read_flag_mask:
+ *   - address bit 7 must be set to request a register read operation
+ */
+static const struct regmap_config zpa2326_regmap_i2c_config = {
+	.reg_bits       = 8,
+	.val_bits       = 8,
+	.writeable_reg  = zpa2326_isreg_writeable,
+	.readable_reg   = zpa2326_isreg_readable,
+	.precious_reg   = zpa2326_isreg_precious,
+	.max_register   = ZPA2326_TEMP_OUT_H_REG,
+	.read_flag_mask = BIT(7),
+	.cache_type     = REGCACHE_NONE,
+};
+
+static unsigned int zpa2326_i2c_hwid(const struct i2c_client *client)
+{
+#define ZPA2326_SA0(_addr)          (_addr & BIT(0))
+#define ZPA2326_DEVICE_ID_SA0_SHIFT (1)
+
+	/* Identification register bit 1 mirrors device address bit 0. */
+	return (ZPA2326_DEVICE_ID |
+		(ZPA2326_SA0(client->addr) << ZPA2326_DEVICE_ID_SA0_SHIFT));
+}
+
+static int zpa2326_probe_i2c(struct i2c_client          *client,
+			     const struct i2c_device_id *i2c_id)
+{
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_i2c(client, &zpa2326_regmap_i2c_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&client->dev, "failed to init registers map");
+		return PTR_ERR(regmap);
+	}
+
+	return zpa2326_probe(&client->dev, i2c_id->name, client->irq,
+			     zpa2326_i2c_hwid(client), regmap);
+}
+
+static void zpa2326_remove_i2c(struct i2c_client *client)
+{
+	zpa2326_remove(&client->dev);
+}
+
+static const struct i2c_device_id zpa2326_i2c_ids[] = {
+	{ "zpa2326", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, zpa2326_i2c_ids);
+
+static const struct of_device_id zpa2326_i2c_matches[] = {
+	{ .compatible = "murata,zpa2326" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, zpa2326_i2c_matches);
+
+static struct i2c_driver zpa2326_i2c_driver = {
+	.driver = {
+		.name           = "zpa2326-i2c",
+		.of_match_table = zpa2326_i2c_matches,
+		.pm             = ZPA2326_PM_OPS,
+	},
+	.probe    = zpa2326_probe_i2c,
+	.remove   = zpa2326_remove_i2c,
+	.id_table = zpa2326_i2c_ids,
+};
+module_i2c_driver(zpa2326_i2c_driver);
+
+MODULE_AUTHOR("Gregor Boirie <gregor.boirie@parrot.com>");
+MODULE_DESCRIPTION("I2C driver for Murata ZPA2326 pressure sensor");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ZPA2326);
diff --git a/drivers/iio/pressure/zpa2326_spi.c b/drivers/iio/pressure/zpa2326_spi.c
new file mode 100644
index 000000000..9c1bcb82d
--- /dev/null
+++ b/drivers/iio/pressure/zpa2326_spi.c
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Murata ZPA2326 SPI pressure and temperature sensor driver
+ *
+ * Copyright (c) 2016 Parrot S.A.
+ *
+ * Author: Gregor Boirie <gregor.boirie@parrot.com>
+ */
+
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/mod_devicetable.h>
+#include "zpa2326.h"
+
+/*
+ * read_flag_mask:
+ *   - address bit 7 must be set to request a register read operation
+ *   - address bit 6 must be set to request register address auto increment
+ */
+static const struct regmap_config zpa2326_regmap_spi_config = {
+	.reg_bits       = 8,
+	.val_bits       = 8,
+	.writeable_reg  = zpa2326_isreg_writeable,
+	.readable_reg   = zpa2326_isreg_readable,
+	.precious_reg   = zpa2326_isreg_precious,
+	.max_register   = ZPA2326_TEMP_OUT_H_REG,
+	.read_flag_mask = BIT(7) | BIT(6),
+	.cache_type     = REGCACHE_NONE,
+};
+
+static int zpa2326_probe_spi(struct spi_device *spi)
+{
+	struct regmap *regmap;
+	int            err;
+
+	regmap = devm_regmap_init_spi(spi, &zpa2326_regmap_spi_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&spi->dev, "failed to init registers map");
+		return PTR_ERR(regmap);
+	}
+
+	/*
+	 * Enforce SPI slave settings to prevent from DT misconfiguration.
+	 *
+	 * Clock is idle high. Sampling happens on trailing edge, i.e., rising
+	 * edge. Maximum bus frequency is 1 MHz. Registers are 8 bits wide.
+	 */
+	spi->mode = SPI_MODE_3;
+	spi->max_speed_hz = min(spi->max_speed_hz, 1000000U);
+	spi->bits_per_word = 8;
+	err = spi_setup(spi);
+	if (err < 0)
+		return err;
+
+	return zpa2326_probe(&spi->dev, spi_get_device_id(spi)->name,
+			     spi->irq, ZPA2326_DEVICE_ID, regmap);
+}
+
+static void zpa2326_remove_spi(struct spi_device *spi)
+{
+	zpa2326_remove(&spi->dev);
+}
+
+static const struct spi_device_id zpa2326_spi_ids[] = {
+	{ "zpa2326", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, zpa2326_spi_ids);
+
+static const struct of_device_id zpa2326_spi_matches[] = {
+	{ .compatible = "murata,zpa2326" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, zpa2326_spi_matches);
+
+static struct spi_driver zpa2326_spi_driver = {
+	.driver = {
+		.name           = "zpa2326-spi",
+		.of_match_table = zpa2326_spi_matches,
+		.pm             = ZPA2326_PM_OPS,
+	},
+	.probe    = zpa2326_probe_spi,
+	.remove   = zpa2326_remove_spi,
+	.id_table = zpa2326_spi_ids,
+};
+module_spi_driver(zpa2326_spi_driver);
+
+MODULE_AUTHOR("Gregor Boirie <gregor.boirie@parrot.com>");
+MODULE_DESCRIPTION("SPI driver for Murata ZPA2326 pressure sensor");
+MODULE_LICENSE("GPL v2");
+MODULE_IMPORT_NS(IIO_ZPA2326);