Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 978 insertions, 0 deletions

diff --git a/drivers/pcmcia/ti113x.h b/drivers/pcmcia/ti113x.h
new file mode 100644
index 000000000..5cb670e03
--- /dev/null
+++ b/drivers/pcmcia/ti113x.h
@@ -0,0 +1,978 @@
+/*
+ * ti113x.h 1.16 1999/10/25 20:03:34
+ *
+ * The contents of this file are subject to the Mozilla Public License
+ * Version 1.1 (the "License"); you may not use this file except in
+ * compliance with the License. You may obtain a copy of the License
+ * at http://www.mozilla.org/MPL/
+ *
+ * Software distributed under the License is distributed on an "AS IS"
+ * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
+ * the License for the specific language governing rights and
+ * limitations under the License. 
+ *
+ * The initial developer of the original code is David A. Hinds
+ * <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
+ * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
+ *
+ * Alternatively, the contents of this file may be used under the
+ * terms of the GNU General Public License version 2 (the "GPL"), in which
+ * case the provisions of the GPL are applicable instead of the
+ * above.  If you wish to allow the use of your version of this file
+ * only under the terms of the GPL and not to allow others to use
+ * your version of this file under the MPL, indicate your decision by
+ * deleting the provisions above and replace them with the notice and
+ * other provisions required by the GPL.  If you do not delete the
+ * provisions above, a recipient may use your version of this file
+ * under either the MPL or the GPL.
+ */
+
+#ifndef _LINUX_TI113X_H
+#define _LINUX_TI113X_H
+
+
+/* Register definitions for TI 113X PCI-to-CardBus bridges */
+
+/* System Control Register */
+#define TI113X_SYSTEM_CONTROL		0x0080	/* 32 bit */
+#define  TI113X_SCR_SMIROUTE		0x04000000
+#define  TI113X_SCR_SMISTATUS		0x02000000
+#define  TI113X_SCR_SMIENB		0x01000000
+#define  TI113X_SCR_VCCPROT		0x00200000
+#define  TI113X_SCR_REDUCEZV		0x00100000
+#define  TI113X_SCR_CDREQEN		0x00080000
+#define  TI113X_SCR_CDMACHAN		0x00070000
+#define  TI113X_SCR_SOCACTIVE		0x00002000
+#define  TI113X_SCR_PWRSTREAM		0x00000800
+#define  TI113X_SCR_DELAYUP		0x00000400
+#define  TI113X_SCR_DELAYDOWN		0x00000200
+#define  TI113X_SCR_INTERROGATE		0x00000100
+#define  TI113X_SCR_CLKRUN_SEL		0x00000080
+#define  TI113X_SCR_PWRSAVINGS		0x00000040
+#define  TI113X_SCR_SUBSYSRW		0x00000020
+#define  TI113X_SCR_CB_DPAR		0x00000010
+#define  TI113X_SCR_CDMA_EN		0x00000008
+#define  TI113X_SCR_ASYNC_IRQ		0x00000004
+#define  TI113X_SCR_KEEPCLK		0x00000002
+#define  TI113X_SCR_CLKRUN_ENA		0x00000001  
+
+#define  TI122X_SCR_SER_STEP		0xc0000000
+#define  TI122X_SCR_INTRTIE		0x20000000
+#define  TIXX21_SCR_TIEALL		0x10000000
+#define  TI122X_SCR_CBRSVD		0x00400000
+#define  TI122X_SCR_MRBURSTDN		0x00008000
+#define  TI122X_SCR_MRBURSTUP		0x00004000
+#define  TI122X_SCR_RIMUX		0x00000001
+
+/* Multimedia Control Register */
+#define TI1250_MULTIMEDIA_CTL		0x0084	/* 8 bit */
+#define  TI1250_MMC_ZVOUTEN		0x80
+#define  TI1250_MMC_PORTSEL		0x40
+#define  TI1250_MMC_ZVEN1		0x02
+#define  TI1250_MMC_ZVEN0		0x01
+
+#define TI1250_GENERAL_STATUS		0x0085	/* 8 bit */
+#define TI1250_GPIO0_CONTROL		0x0088	/* 8 bit */
+#define TI1250_GPIO1_CONTROL		0x0089	/* 8 bit */
+#define TI1250_GPIO2_CONTROL		0x008a	/* 8 bit */
+#define TI1250_GPIO3_CONTROL		0x008b	/* 8 bit */
+#define TI1250_GPIO_MODE_MASK		0xc0
+
+/* IRQMUX/MFUNC Register */
+#define TI122X_MFUNC			0x008c	/* 32 bit */
+#define TI122X_MFUNC0_MASK		0x0000000f
+#define TI122X_MFUNC1_MASK		0x000000f0
+#define TI122X_MFUNC2_MASK		0x00000f00
+#define TI122X_MFUNC3_MASK		0x0000f000
+#define TI122X_MFUNC4_MASK		0x000f0000
+#define TI122X_MFUNC5_MASK		0x00f00000
+#define TI122X_MFUNC6_MASK		0x0f000000
+
+#define TI122X_MFUNC0_INTA		0x00000002
+#define TI125X_MFUNC0_INTB		0x00000001
+#define TI122X_MFUNC1_INTB		0x00000020
+#define TI122X_MFUNC3_IRQSER		0x00001000
+
+
+/* Retry Status Register */
+#define TI113X_RETRY_STATUS		0x0090	/* 8 bit */
+#define  TI113X_RSR_PCIRETRY		0x80
+#define  TI113X_RSR_CBRETRY		0x40
+#define  TI113X_RSR_TEXP_CBB		0x20
+#define  TI113X_RSR_MEXP_CBB		0x10
+#define  TI113X_RSR_TEXP_CBA		0x08
+#define  TI113X_RSR_MEXP_CBA		0x04
+#define  TI113X_RSR_TEXP_PCI		0x02
+#define  TI113X_RSR_MEXP_PCI		0x01
+
+/* Card Control Register */
+#define TI113X_CARD_CONTROL		0x0091	/* 8 bit */
+#define  TI113X_CCR_RIENB		0x80
+#define  TI113X_CCR_ZVENABLE		0x40
+#define  TI113X_CCR_PCI_IRQ_ENA		0x20
+#define  TI113X_CCR_PCI_IREQ		0x10
+#define  TI113X_CCR_PCI_CSC		0x08
+#define  TI113X_CCR_SPKROUTEN		0x02
+#define  TI113X_CCR_IFG			0x01
+
+#define  TI1220_CCR_PORT_SEL		0x20
+#define  TI122X_CCR_AUD2MUX		0x04
+
+/* Device Control Register */
+#define TI113X_DEVICE_CONTROL		0x0092	/* 8 bit */
+#define  TI113X_DCR_5V_FORCE		0x40
+#define  TI113X_DCR_3V_FORCE		0x20
+#define  TI113X_DCR_IMODE_MASK		0x06
+#define  TI113X_DCR_IMODE_ISA		0x02
+#define  TI113X_DCR_IMODE_SERIAL	0x04
+
+#define  TI12XX_DCR_IMODE_PCI_ONLY	0x00
+#define  TI12XX_DCR_IMODE_ALL_SERIAL	0x06
+
+/* Buffer Control Register */
+#define TI113X_BUFFER_CONTROL		0x0093	/* 8 bit */
+#define  TI113X_BCR_CB_READ_DEPTH	0x08
+#define  TI113X_BCR_CB_WRITE_DEPTH	0x04
+#define  TI113X_BCR_PCI_READ_DEPTH	0x02
+#define  TI113X_BCR_PCI_WRITE_DEPTH	0x01
+
+/* Diagnostic Register */
+#define TI1250_DIAGNOSTIC		0x0093	/* 8 bit */
+#define  TI1250_DIAG_TRUE_VALUE		0x80
+#define  TI1250_DIAG_PCI_IREQ		0x40
+#define  TI1250_DIAG_PCI_CSC		0x20
+#define  TI1250_DIAG_ASYNC_CSC		0x01
+
+/* DMA Registers */
+#define TI113X_DMA_0			0x0094	/* 32 bit */
+#define TI113X_DMA_1			0x0098	/* 32 bit */
+
+/* ExCA IO offset registers */
+#define TI113X_IO_OFFSET(map)		(0x36+((map)<<1))
+
+/* EnE test register */
+#define ENE_TEST_C9			0xc9	/* 8bit */
+#define ENE_TEST_C9_TLTENABLE		0x02
+#define ENE_TEST_C9_PFENABLE_F0		0x04
+#define ENE_TEST_C9_PFENABLE_F1		0x08
+#define ENE_TEST_C9_PFENABLE		(ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F1)
+#define ENE_TEST_C9_WPDISALBLE_F0	0x40
+#define ENE_TEST_C9_WPDISALBLE_F1	0x80
+#define ENE_TEST_C9_WPDISALBLE		(ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
+
+/*
+ * Texas Instruments CardBus controller overrides.
+ */
+#define ti_sysctl(socket)	((socket)->private[0])
+#define ti_cardctl(socket)	((socket)->private[1])
+#define ti_devctl(socket)	((socket)->private[2])
+#define ti_diag(socket)		((socket)->private[3])
+#define ti_mfunc(socket)	((socket)->private[4])
+#define ene_test_c9(socket)	((socket)->private[5])
+
+/*
+ * These are the TI specific power management handlers.
+ */
+static void ti_save_state(struct yenta_socket *socket)
+{
+	ti_sysctl(socket) = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	ti_mfunc(socket) = config_readl(socket, TI122X_MFUNC);
+	ti_cardctl(socket) = config_readb(socket, TI113X_CARD_CONTROL);
+	ti_devctl(socket) = config_readb(socket, TI113X_DEVICE_CONTROL);
+	ti_diag(socket) = config_readb(socket, TI1250_DIAGNOSTIC);
+
+	if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
+		ene_test_c9(socket) = config_readb(socket, ENE_TEST_C9);
+}
+
+static void ti_restore_state(struct yenta_socket *socket)
+{
+	config_writel(socket, TI113X_SYSTEM_CONTROL, ti_sysctl(socket));
+	config_writel(socket, TI122X_MFUNC, ti_mfunc(socket));
+	config_writeb(socket, TI113X_CARD_CONTROL, ti_cardctl(socket));
+	config_writeb(socket, TI113X_DEVICE_CONTROL, ti_devctl(socket));
+	config_writeb(socket, TI1250_DIAGNOSTIC, ti_diag(socket));
+
+	if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
+		config_writeb(socket, ENE_TEST_C9, ene_test_c9(socket));
+}
+
+/*
+ *	Zoom video control for TI122x/113x chips
+ */
+
+static void ti_zoom_video(struct pcmcia_socket *sock, int onoff)
+{
+	u8 reg;
+	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+
+	/* If we don't have a Zoom Video switch this is harmless,
+	   we just tristate the unused (ZV) lines */
+	reg = config_readb(socket, TI113X_CARD_CONTROL);
+	if (onoff)
+		/* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
+		reg |= TI113X_CCR_ZVENABLE;
+	else
+		reg &= ~TI113X_CCR_ZVENABLE;
+	config_writeb(socket, TI113X_CARD_CONTROL, reg);
+}
+
+/*
+ *	The 145x series can also use this. They have an additional
+ *	ZV autodetect mode we don't use but don't actually need.
+ *	FIXME: manual says its in func0 and func1 but disagrees with
+ *	itself about this - do we need to force func0, if so we need
+ *	to know a lot more about socket pairings in pcmcia_socket than
+ *	we do now.. uggh.
+ */
+ 
+static void ti1250_zoom_video(struct pcmcia_socket *sock, int onoff)
+{	
+	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+	int shift = 0;
+	u8 reg;
+
+	ti_zoom_video(sock, onoff);
+
+	reg = config_readb(socket, TI1250_MULTIMEDIA_CTL);
+	reg |= TI1250_MMC_ZVOUTEN;	/* ZV bus enable */
+
+	if(PCI_FUNC(socket->dev->devfn)==1)
+		shift = 1;
+	
+	if(onoff)
+	{
+		reg &= ~(1<<6); 	/* Clear select bit */
+		reg |= shift<<6;	/* Favour our socket */
+		reg |= 1<<shift;	/* Socket zoom video on */
+	}
+	else
+	{
+		reg &= ~(1<<6); 	/* Clear select bit */
+		reg |= (1^shift)<<6;	/* Favour other socket */
+		reg &= ~(1<<shift);	/* Socket zoon video off */
+	}
+
+	config_writeb(socket, TI1250_MULTIMEDIA_CTL, reg);
+}
+
+static void ti_set_zv(struct yenta_socket *socket)
+{
+	if(socket->dev->vendor == PCI_VENDOR_ID_TI)
+	{
+		switch(socket->dev->device)
+		{
+			/* There may be more .. */
+			case PCI_DEVICE_ID_TI_1220:
+			case PCI_DEVICE_ID_TI_1221:
+			case PCI_DEVICE_ID_TI_1225:
+			case PCI_DEVICE_ID_TI_4510:
+				socket->socket.zoom_video = ti_zoom_video;
+				break;	
+			case PCI_DEVICE_ID_TI_1250:
+			case PCI_DEVICE_ID_TI_1251A:
+			case PCI_DEVICE_ID_TI_1251B:
+			case PCI_DEVICE_ID_TI_1450:
+				socket->socket.zoom_video = ti1250_zoom_video;
+		}
+	}
+}
+
+
+/*
+ * Generic TI init - TI has an extension for the
+ * INTCTL register that sets the PCI CSC interrupt.
+ * Make sure we set it correctly at open and init
+ * time
+ * - override: disable the PCI CSC interrupt. This makes
+ *   it possible to use the CSC interrupt to probe the
+ *   ISA interrupts.
+ * - init: set the interrupt to match our PCI state.
+ *   This makes us correctly get PCI CSC interrupt
+ *   events.
+ */
+static int ti_init(struct yenta_socket *socket)
+{
+	u8 new, reg = exca_readb(socket, I365_INTCTL);
+
+	new = reg & ~I365_INTR_ENA;
+	if (socket->dev->irq)
+		new |= I365_INTR_ENA;
+	if (new != reg)
+		exca_writeb(socket, I365_INTCTL, new);
+	return 0;
+}
+
+static int ti_override(struct yenta_socket *socket)
+{
+	u8 new, reg = exca_readb(socket, I365_INTCTL);
+
+	new = reg & ~I365_INTR_ENA;
+	if (new != reg)
+		exca_writeb(socket, I365_INTCTL, new);
+
+	ti_set_zv(socket);
+
+	return 0;
+}
+
+static void ti113x_use_isa_irq(struct yenta_socket *socket)
+{
+	int isa_irq = -1;
+	u8 intctl;
+	u32 isa_irq_mask = 0;
+
+	if (!isa_probe)
+		return;
+
+	/* get a free isa int */
+	isa_irq_mask = yenta_probe_irq(socket, isa_interrupts);
+	if (!isa_irq_mask)
+		return; /* no useable isa irq found */
+
+	/* choose highest available */
+	for (; isa_irq_mask; isa_irq++)
+		isa_irq_mask >>= 1;
+	socket->cb_irq = isa_irq;
+
+	exca_writeb(socket, I365_CSCINT, (isa_irq << 4));
+
+	intctl = exca_readb(socket, I365_INTCTL);
+	intctl &= ~(I365_INTR_ENA | I365_IRQ_MASK);     /* CSC Enable */
+	exca_writeb(socket, I365_INTCTL, intctl);
+
+	dev_info(&socket->dev->dev,
+		"Yenta TI113x: using isa irq %d for CardBus\n", isa_irq);
+}
+
+
+static int ti113x_override(struct yenta_socket *socket)
+{
+	u8 cardctl;
+
+	cardctl = config_readb(socket, TI113X_CARD_CONTROL);
+	cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
+	if (socket->dev->irq)
+		cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
+	else
+		ti113x_use_isa_irq(socket);
+
+	config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
+
+	return ti_override(socket);
+}
+
+
+/* irqrouting for func0, probes PCI interrupt and ISA interrupts */
+static void ti12xx_irqroute_func0(struct yenta_socket *socket)
+{
+	u32 mfunc, mfunc_old, devctl;
+	u8 gpio3, gpio3_old;
+	int pci_irq_status;
+
+	mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
+	devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
+	dev_info(&socket->dev->dev, "TI: mfunc 0x%08x, devctl 0x%02x\n",
+		 mfunc, devctl);
+
+	/* make sure PCI interrupts are enabled before probing */
+	ti_init(socket);
+
+	/* test PCI interrupts first. only try fixing if return value is 0! */
+	pci_irq_status = yenta_probe_cb_irq(socket);
+	if (pci_irq_status)
+		goto out;
+
+	/*
+	 * We're here which means PCI interrupts are _not_ delivered. try to
+	 * find the right setting (all serial or parallel)
+	 */
+	dev_info(&socket->dev->dev,
+		 "TI: probing PCI interrupt failed, trying to fix\n");
+
+	/* for serial PCI make sure MFUNC3 is set to IRQSER */
+	if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
+		switch (socket->dev->device) {
+		case PCI_DEVICE_ID_TI_1250:
+		case PCI_DEVICE_ID_TI_1251A:
+		case PCI_DEVICE_ID_TI_1251B:
+		case PCI_DEVICE_ID_TI_1450:
+		case PCI_DEVICE_ID_TI_1451A:
+		case PCI_DEVICE_ID_TI_4450:
+		case PCI_DEVICE_ID_TI_4451:
+			/* these chips have no IRQSER setting in MFUNC3  */
+			break;
+
+		default:
+			mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
+
+			/* write down if changed, probe */
+			if (mfunc != mfunc_old) {
+				config_writel(socket, TI122X_MFUNC, mfunc);
+
+				pci_irq_status = yenta_probe_cb_irq(socket);
+				if (pci_irq_status == 1) {
+					dev_info(&socket->dev->dev,
+						 "TI: all-serial interrupts ok\n");
+					mfunc_old = mfunc;
+					goto out;
+				}
+
+				/* not working, back to old value */
+				mfunc = mfunc_old;
+				config_writel(socket, TI122X_MFUNC, mfunc);
+
+				if (pci_irq_status == -1)
+					goto out;
+			}
+		}
+
+		/* serial PCI interrupts not working fall back to parallel */
+		dev_info(&socket->dev->dev,
+			 "TI: falling back to parallel PCI interrupts\n");
+		devctl &= ~TI113X_DCR_IMODE_MASK;
+		devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
+		config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
+	}
+
+	/* parallel PCI interrupts: route INTA */
+	switch (socket->dev->device) {
+	case PCI_DEVICE_ID_TI_1250:
+	case PCI_DEVICE_ID_TI_1251A:
+	case PCI_DEVICE_ID_TI_1251B:
+	case PCI_DEVICE_ID_TI_1450:
+		/* make sure GPIO3 is set to INTA */
+		gpio3 = gpio3_old = config_readb(socket, TI1250_GPIO3_CONTROL);
+		gpio3 &= ~TI1250_GPIO_MODE_MASK;
+		if (gpio3 != gpio3_old)
+			config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
+		break;
+
+	default:
+		gpio3 = gpio3_old = 0;
+
+		mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI122X_MFUNC0_INTA;
+		if (mfunc != mfunc_old)
+			config_writel(socket, TI122X_MFUNC, mfunc);
+	}
+
+	/* time to probe again */
+	pci_irq_status = yenta_probe_cb_irq(socket);
+	if (pci_irq_status == 1) {
+		mfunc_old = mfunc;
+		dev_info(&socket->dev->dev, "TI: parallel PCI interrupts ok\n");
+	} else {
+		/* not working, back to old value */
+		mfunc = mfunc_old;
+		config_writel(socket, TI122X_MFUNC, mfunc);
+		if (gpio3 != gpio3_old)
+			config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3_old);
+	}
+
+out:
+	if (pci_irq_status < 1) {
+		socket->cb_irq = 0;
+		dev_info(&socket->dev->dev,
+			 "Yenta TI: no PCI interrupts. Fish. Please report.\n");
+	}
+}
+
+
+/* changes the irq of func1 to match that of func0 */
+static int ti12xx_align_irqs(struct yenta_socket *socket, int *old_irq)
+{
+	struct pci_dev *func0;
+
+	/* find func0 device */
+	func0 = pci_get_slot(socket->dev->bus, socket->dev->devfn & ~0x07);
+	if (!func0)
+		return 0;
+
+	if (old_irq)
+		*old_irq = socket->cb_irq;
+	socket->cb_irq = socket->dev->irq = func0->irq;
+
+	pci_dev_put(func0);
+
+	return 1;
+}
+
+/*
+ * ties INTA and INTB together. also changes the devices irq to that of
+ * the function 0 device. call from func1 only.
+ * returns 1 if INTRTIE changed, 0 otherwise.
+ */
+static int ti12xx_tie_interrupts(struct yenta_socket *socket, int *old_irq)
+{
+	u32 sysctl;
+	int ret;
+
+	sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	if (sysctl & TI122X_SCR_INTRTIE)
+		return 0;
+
+	/* align */
+	ret = ti12xx_align_irqs(socket, old_irq);
+	if (!ret)
+		return 0;
+
+	/* tie */
+	sysctl |= TI122X_SCR_INTRTIE;
+	config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
+
+	return 1;
+}
+
+/* undo what ti12xx_tie_interrupts() did */
+static void ti12xx_untie_interrupts(struct yenta_socket *socket, int old_irq)
+{
+	u32 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	sysctl &= ~TI122X_SCR_INTRTIE;
+	config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
+
+	socket->cb_irq = socket->dev->irq = old_irq;
+}
+
+/* 
+ * irqrouting for func1, plays with INTB routing
+ * only touches MFUNC for INTB routing. all other bits are taken
+ * care of in func0 already.
+ */
+static void ti12xx_irqroute_func1(struct yenta_socket *socket)
+{
+	u32 mfunc, mfunc_old, devctl, sysctl;
+	int pci_irq_status;
+
+	mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
+	devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
+	dev_info(&socket->dev->dev, "TI: mfunc 0x%08x, devctl 0x%02x\n",
+		 mfunc, devctl);
+
+	/* if IRQs are configured as tied, align irq of func1 with func0 */
+	sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	if (sysctl & TI122X_SCR_INTRTIE)
+		ti12xx_align_irqs(socket, NULL);
+
+	/* make sure PCI interrupts are enabled before probing */
+	ti_init(socket);
+
+	/* test PCI interrupts first. only try fixing if return value is 0! */
+	pci_irq_status = yenta_probe_cb_irq(socket);
+	if (pci_irq_status)
+		goto out;
+
+	/*
+	 * We're here which means PCI interrupts are _not_ delivered. try to
+	 * find the right setting
+	 */
+	dev_info(&socket->dev->dev,
+		 "TI: probing PCI interrupt failed, trying to fix\n");
+
+	/* if all serial: set INTRTIE, probe again */
+	if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
+		int old_irq;
+
+		if (ti12xx_tie_interrupts(socket, &old_irq)) {
+			pci_irq_status = yenta_probe_cb_irq(socket);
+			if (pci_irq_status == 1) {
+				dev_info(&socket->dev->dev,
+					 "TI: all-serial interrupts, tied ok\n");
+				goto out;
+			}
+
+			ti12xx_untie_interrupts(socket, old_irq);
+		}
+	}
+	/* parallel PCI: route INTB, probe again */
+	else {
+		int old_irq;
+
+		switch (socket->dev->device) {
+		case PCI_DEVICE_ID_TI_1250:
+			/* the 1250 has one pin for IRQSER/INTB depending on devctl */
+			break;
+
+		case PCI_DEVICE_ID_TI_1251A:
+		case PCI_DEVICE_ID_TI_1251B:
+		case PCI_DEVICE_ID_TI_1450:
+			/*
+			 *  those have a pin for IRQSER/INTB plus INTB in MFUNC0
+			 *  we alread probed the shared pin, now go for MFUNC0
+			 */
+			mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI125X_MFUNC0_INTB;
+			break;
+
+		default:
+			mfunc = (mfunc & ~TI122X_MFUNC1_MASK) | TI122X_MFUNC1_INTB;
+			break;
+		}
+
+		/* write, probe */
+		if (mfunc != mfunc_old) {
+			config_writel(socket, TI122X_MFUNC, mfunc);
+
+			pci_irq_status = yenta_probe_cb_irq(socket);
+			if (pci_irq_status == 1) {
+				dev_info(&socket->dev->dev,
+					 "TI: parallel PCI interrupts ok\n");
+				goto out;
+			}
+
+			mfunc = mfunc_old;
+			config_writel(socket, TI122X_MFUNC, mfunc);
+
+			if (pci_irq_status == -1)
+				goto out;
+		}
+
+		/* still nothing: set INTRTIE */
+		if (ti12xx_tie_interrupts(socket, &old_irq)) {
+			pci_irq_status = yenta_probe_cb_irq(socket);
+			if (pci_irq_status == 1) {
+				dev_info(&socket->dev->dev,
+					 "TI: parallel PCI interrupts, tied ok\n");
+				goto out;
+			}
+
+			ti12xx_untie_interrupts(socket, old_irq);
+		}
+	}
+
+out:
+	if (pci_irq_status < 1) {
+		socket->cb_irq = 0;
+		dev_info(&socket->dev->dev,
+			 "TI: no PCI interrupts. Fish. Please report.\n");
+	}
+}
+
+
+/* Returns true value if the second slot of a two-slot controller is empty */
+static int ti12xx_2nd_slot_empty(struct yenta_socket *socket)
+{
+	struct pci_dev *func;
+	struct yenta_socket *slot2;
+	int devfn;
+	unsigned int state;
+	int ret = 1;
+	u32 sysctl;
+
+	/* catch the two-slot controllers */
+	switch (socket->dev->device) {
+	case PCI_DEVICE_ID_TI_1220:
+	case PCI_DEVICE_ID_TI_1221:
+	case PCI_DEVICE_ID_TI_1225:
+	case PCI_DEVICE_ID_TI_1251A:
+	case PCI_DEVICE_ID_TI_1251B:
+	case PCI_DEVICE_ID_TI_1420:
+	case PCI_DEVICE_ID_TI_1450:
+	case PCI_DEVICE_ID_TI_1451A:
+	case PCI_DEVICE_ID_TI_1520:
+	case PCI_DEVICE_ID_TI_1620:
+	case PCI_DEVICE_ID_TI_4520:
+	case PCI_DEVICE_ID_TI_4450:
+	case PCI_DEVICE_ID_TI_4451:
+		/*
+		 * there are way more, but they need to be added in yenta_socket.c
+		 * and pci_ids.h first anyway.
+		 */
+		break;
+
+	case PCI_DEVICE_ID_TI_XX12:
+	case PCI_DEVICE_ID_TI_X515:
+	case PCI_DEVICE_ID_TI_X420:
+	case PCI_DEVICE_ID_TI_X620:
+	case PCI_DEVICE_ID_TI_XX21_XX11:
+	case PCI_DEVICE_ID_TI_7410:
+	case PCI_DEVICE_ID_TI_7610:
+		/*
+		 * those are either single or dual slot CB with additional functions
+		 * like 1394, smartcard reader, etc. check the TIEALL flag for them
+		 * the TIEALL flag binds the IRQ of all functions together.
+		 * we catch the single slot variants later.
+		 */
+		sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+		if (sysctl & TIXX21_SCR_TIEALL)
+			return 0;
+
+		break;
+
+	/* single-slot controllers have the 2nd slot empty always :) */
+	default:
+		return 1;
+	}
+
+	/* get other slot */
+	devfn = socket->dev->devfn & ~0x07;
+	func = pci_get_slot(socket->dev->bus,
+	                    (socket->dev->devfn & 0x07) ? devfn : devfn | 0x01);
+	if (!func)
+		return 1;
+
+	/*
+	 * check that the device id of both slots match. this is needed for the
+	 * XX21 and the XX11 controller that share the same device id for single
+	 * and dual slot controllers. return '2nd slot empty'. we already checked
+	 * if the interrupt is tied to another function.
+	 */
+	if (socket->dev->device != func->device)
+		goto out;
+
+	slot2 = pci_get_drvdata(func);
+	if (!slot2)
+		goto out;
+
+	/* check state */
+	yenta_get_status(&slot2->socket, &state);
+	if (state & SS_DETECT) {
+		ret = 0;
+		goto out;
+	}
+
+out:
+	pci_dev_put(func);
+	return ret;
+}
+
+/*
+ * TI specifiy parts for the power hook.
+ *
+ * some TI's with some CB's produces interrupt storm on power on. it has been
+ * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
+ * disable any CB interrupts during this time.
+ */
+static int ti12xx_power_hook(struct pcmcia_socket *sock, int operation)
+{
+	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+	u32 mfunc, devctl, sysctl;
+	u8 gpio3;
+
+	/* only POWER_PRE and POWER_POST are interesting */
+	if ((operation != HOOK_POWER_PRE) && (operation != HOOK_POWER_POST))
+		return 0;
+
+	devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
+	sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	mfunc = config_readl(socket, TI122X_MFUNC);
+
+	/*
+	 * all serial/tied: only disable when modparm set. always doing it
+	 * would mean a regression for working setups 'cos it disables the
+	 * interrupts for both both slots on 2-slot controllers
+	 * (and users of single slot controllers where it's save have to
+	 * live with setting the modparm, most don't have to anyway)
+	 */
+	if (((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) &&
+	    (pwr_irqs_off || ti12xx_2nd_slot_empty(socket))) {
+		switch (socket->dev->device) {
+		case PCI_DEVICE_ID_TI_1250:
+		case PCI_DEVICE_ID_TI_1251A:
+		case PCI_DEVICE_ID_TI_1251B:
+		case PCI_DEVICE_ID_TI_1450:
+		case PCI_DEVICE_ID_TI_1451A:
+		case PCI_DEVICE_ID_TI_4450:
+		case PCI_DEVICE_ID_TI_4451:
+			/* these chips have no IRQSER setting in MFUNC3  */
+			break;
+
+		default:
+			if (operation == HOOK_POWER_PRE)
+				mfunc = (mfunc & ~TI122X_MFUNC3_MASK);
+			else
+				mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
+		}
+
+		return 0;
+	}
+
+	/* do the job differently for func0/1 */
+	if ((PCI_FUNC(socket->dev->devfn) == 0) ||
+	    ((sysctl & TI122X_SCR_INTRTIE) &&
+	     (pwr_irqs_off || ti12xx_2nd_slot_empty(socket)))) {
+		/* some bridges are different */
+		switch (socket->dev->device) {
+		case PCI_DEVICE_ID_TI_1250:
+		case PCI_DEVICE_ID_TI_1251A:
+		case PCI_DEVICE_ID_TI_1251B:
+		case PCI_DEVICE_ID_TI_1450:
+			/* those oldies use gpio3 for INTA */
+			gpio3 = config_readb(socket, TI1250_GPIO3_CONTROL);
+			if (operation == HOOK_POWER_PRE)
+				gpio3 = (gpio3 & ~TI1250_GPIO_MODE_MASK) | 0x40;
+			else
+				gpio3 &= ~TI1250_GPIO_MODE_MASK;
+			config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
+			break;
+
+		default:
+			/* all new bridges are the same */
+			if (operation == HOOK_POWER_PRE)
+				mfunc &= ~TI122X_MFUNC0_MASK;
+			else
+				mfunc |= TI122X_MFUNC0_INTA;
+			config_writel(socket, TI122X_MFUNC, mfunc);
+		}
+	} else {
+		switch (socket->dev->device) {
+		case PCI_DEVICE_ID_TI_1251A:
+		case PCI_DEVICE_ID_TI_1251B:
+		case PCI_DEVICE_ID_TI_1450:
+			/* those have INTA elsewhere and INTB in MFUNC0 */
+			if (operation == HOOK_POWER_PRE)
+				mfunc &= ~TI122X_MFUNC0_MASK;
+			else
+				mfunc |= TI125X_MFUNC0_INTB;
+			config_writel(socket, TI122X_MFUNC, mfunc);
+
+			break;
+
+		default:
+			/* all new bridges are the same */
+			if (operation == HOOK_POWER_PRE)
+				mfunc &= ~TI122X_MFUNC1_MASK;
+			else
+				mfunc |= TI122X_MFUNC1_INTB;
+			config_writel(socket, TI122X_MFUNC, mfunc);
+		}
+	}
+
+	return 0;
+}
+
+static int ti12xx_override(struct yenta_socket *socket)
+{
+	u32 val, val_orig;
+
+	/* make sure that memory burst is active */
+	val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
+	if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
+		dev_info(&socket->dev->dev, "Disabling CLKRUN feature\n");
+		val |= TI113X_SCR_KEEPCLK;
+	}
+	if (!(val & TI122X_SCR_MRBURSTUP)) {
+		dev_info(&socket->dev->dev,
+			 "Enabling burst memory read transactions\n");
+		val |= TI122X_SCR_MRBURSTUP;
+	}
+	if (val_orig != val)
+		config_writel(socket, TI113X_SYSTEM_CONTROL, val);
+
+	/*
+	 * Yenta expects controllers to use CSCINT to route
+	 * CSC interrupts to PCI rather than INTVAL.
+	 */
+	val = config_readb(socket, TI1250_DIAGNOSTIC);
+	dev_info(&socket->dev->dev, "Using %s to route CSC interrupts to PCI\n",
+		 (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
+	dev_info(&socket->dev->dev, "Routing CardBus interrupts to %s\n",
+		 (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
+
+	/* do irqrouting, depending on function */
+	if (PCI_FUNC(socket->dev->devfn) == 0)
+		ti12xx_irqroute_func0(socket);
+	else
+		ti12xx_irqroute_func1(socket);
+
+	/* install power hook */
+	socket->socket.power_hook = ti12xx_power_hook;
+
+	return ti_override(socket);
+}
+
+
+static int ti1250_override(struct yenta_socket *socket)
+{
+	u8 old, diag;
+
+	old = config_readb(socket, TI1250_DIAGNOSTIC);
+	diag = old & ~(TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ);
+	if (socket->cb_irq)
+		diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
+
+	if (diag != old) {
+		dev_info(&socket->dev->dev,
+			 "adjusting diagnostic: %02x -> %02x\n",
+			 old, diag);
+		config_writeb(socket, TI1250_DIAGNOSTIC, diag);
+	}
+
+	return ti12xx_override(socket);
+}
+
+
+/**
+ * EnE specific part. EnE bridges are register compatible with TI bridges but
+ * have their own test registers and more important their own little problems.
+ * Some fixup code to make everybody happy (TM).
+ */
+
+#ifdef CONFIG_YENTA_ENE_TUNE
+/*
+ * set/clear various test bits:
+ * Defaults to clear the bit.
+ * - mask (u8) defines what bits to change
+ * - bits (u8) is the values to change them to
+ * -> it's
+ * 	current = (current & ~mask) | bits
+ */
+/* pci ids of devices that wants to have the bit set */
+#define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) {		\
+		.vendor		= _vend,			\
+		.device		= _dev,				\
+		.subvendor	= _subvend,			\
+		.subdevice	= _subdev,			\
+		.driver_data	= ((mask) << 8 | (bits)),	\
+	}
+static struct pci_device_id ene_tune_tbl[] = {
+	/* Echo Audio products based on motorola DSP56301 and DSP56361 */
+	DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
+		ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+	DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
+		ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+
+	{}
+};
+
+static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
+{
+	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+	struct pci_dev *dev;
+	struct pci_device_id *id = NULL;
+	u8 test_c9, old_c9, mask, bits;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
+		if (id)
+			break;
+	}
+
+	test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
+	if (id) {
+		mask = (id->driver_data >> 8) & 0xFF;
+		bits = id->driver_data & 0xFF;
+
+		test_c9 = (test_c9 & ~mask) | bits;
+	}
+	else
+		/* default to clear TLTEnable bit, old behaviour */
+		test_c9 &= ~ENE_TEST_C9_TLTENABLE;
+
+	dev_info(&socket->dev->dev,
+		 "EnE: changing testregister 0xC9, %02x -> %02x\n",
+		 old_c9, test_c9);
+	config_writeb(socket, ENE_TEST_C9, test_c9);
+}
+
+static int ene_override(struct yenta_socket *socket)
+{
+	/* install tune_bridge() function */
+	socket->socket.tune_bridge = ene_tune_bridge;
+
+	return ti1250_override(socket);
+}
+#else
+#  define ene_override ti1250_override
+#endif /* !CONFIG_YENTA_ENE_TUNE */
+
+#endif /* _LINUX_TI113X_H */
+