Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 384 insertions, 0 deletions

diff --git a/drivers/phy/marvell/phy-mvebu-cp110-utmi.c b/drivers/phy/marvell/phy-mvebu-cp110-utmi.c
new file mode 100644
index 000000000..aa27c7994
--- /dev/null
+++ b/drivers/phy/marvell/phy-mvebu-cp110-utmi.c
@@ -0,0 +1,384 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Marvell
+ *
+ * Authors:
+ *   Konstantin Porotchkin <kostap@marvell.com>
+ *
+ * Marvell CP110 UTMI PHY driver
+ */
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/usb/of.h>
+#include <linux/usb/otg.h>
+
+#define UTMI_PHY_PORTS				2
+
+/* CP110 UTMI register macro definetions */
+#define SYSCON_USB_CFG_REG			0x420
+#define   USB_CFG_DEVICE_EN_MASK		BIT(0)
+#define   USB_CFG_DEVICE_MUX_OFFSET		1
+#define   USB_CFG_DEVICE_MUX_MASK		BIT(1)
+#define   USB_CFG_PLL_MASK			BIT(25)
+
+#define SYSCON_UTMI_CFG_REG(id)			(0x440 + (id) * 4)
+#define   UTMI_PHY_CFG_PU_MASK			BIT(5)
+
+#define UTMI_PLL_CTRL_REG			0x0
+#define   PLL_REFDIV_OFFSET			0
+#define   PLL_REFDIV_MASK			GENMASK(6, 0)
+#define   PLL_REFDIV_VAL			0x5
+#define   PLL_FBDIV_OFFSET			16
+#define   PLL_FBDIV_MASK			GENMASK(24, 16)
+#define   PLL_FBDIV_VAL				0x60
+#define   PLL_SEL_LPFR_MASK			GENMASK(29, 28)
+#define   PLL_RDY				BIT(31)
+#define UTMI_CAL_CTRL_REG			0x8
+#define   IMPCAL_VTH_OFFSET			8
+#define   IMPCAL_VTH_MASK			GENMASK(10, 8)
+#define   IMPCAL_VTH_VAL			0x7
+#define   IMPCAL_DONE				BIT(23)
+#define   PLLCAL_DONE				BIT(31)
+#define UTMI_TX_CH_CTRL_REG			0xC
+#define   DRV_EN_LS_OFFSET			12
+#define   DRV_EN_LS_MASK			GENMASK(15, 12)
+#define   IMP_SEL_LS_OFFSET			16
+#define   IMP_SEL_LS_MASK			GENMASK(19, 16)
+#define   TX_AMP_OFFSET				20
+#define   TX_AMP_MASK				GENMASK(22, 20)
+#define   TX_AMP_VAL				0x4
+#define UTMI_RX_CH_CTRL0_REG			0x14
+#define   SQ_DET_EN				BIT(15)
+#define   SQ_ANA_DTC_SEL			BIT(28)
+#define UTMI_RX_CH_CTRL1_REG			0x18
+#define   SQ_AMP_CAL_OFFSET			0
+#define   SQ_AMP_CAL_MASK			GENMASK(2, 0)
+#define   SQ_AMP_CAL_VAL			1
+#define   SQ_AMP_CAL_EN				BIT(3)
+#define UTMI_CTRL_STATUS0_REG			0x24
+#define   SUSPENDM				BIT(22)
+#define   TEST_SEL				BIT(25)
+#define UTMI_CHGDTC_CTRL_REG			0x38
+#define   VDAT_OFFSET				8
+#define   VDAT_MASK				GENMASK(9, 8)
+#define   VDAT_VAL				1
+#define   VSRC_OFFSET				10
+#define   VSRC_MASK				GENMASK(11, 10)
+#define   VSRC_VAL				1
+
+#define PLL_LOCK_DELAY_US			10000
+#define PLL_LOCK_TIMEOUT_US			1000000
+
+#define PORT_REGS(p)				((p)->priv->regs + (p)->id * 0x1000)
+
+/**
+ * struct mvebu_cp110_utmi - PHY driver data
+ *
+ * @regs: PHY registers
+ * @syscon: Regmap with system controller registers
+ * @dev: device driver handle
+ * @ops: phy ops
+ */
+struct mvebu_cp110_utmi {
+	void __iomem *regs;
+	struct regmap *syscon;
+	struct device *dev;
+	const struct phy_ops *ops;
+};
+
+/**
+ * struct mvebu_cp110_utmi_port - PHY port data
+ *
+ * @priv: PHY driver data
+ * @id: PHY port ID
+ * @dr_mode: PHY connection: USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL
+ */
+struct mvebu_cp110_utmi_port {
+	struct mvebu_cp110_utmi *priv;
+	u32 id;
+	enum usb_dr_mode dr_mode;
+};
+
+static void mvebu_cp110_utmi_port_setup(struct mvebu_cp110_utmi_port *port)
+{
+	u32 reg;
+
+	/*
+	 * Setup PLL.
+	 * The reference clock is the frequency of quartz resonator
+	 * connected to pins REFCLK_XIN and REFCLK_XOUT of the SoC.
+	 * Register init values are matching the 40MHz default clock.
+	 * The crystal used for all platform boards is now 25MHz.
+	 * See the functional specification for details.
+	 */
+	reg = readl(PORT_REGS(port) + UTMI_PLL_CTRL_REG);
+	reg &= ~(PLL_REFDIV_MASK | PLL_FBDIV_MASK | PLL_SEL_LPFR_MASK);
+	reg |= (PLL_REFDIV_VAL << PLL_REFDIV_OFFSET) |
+	       (PLL_FBDIV_VAL << PLL_FBDIV_OFFSET);
+	writel(reg, PORT_REGS(port) + UTMI_PLL_CTRL_REG);
+
+	/* Impedance Calibration Threshold Setting */
+	reg = readl(PORT_REGS(port) + UTMI_CAL_CTRL_REG);
+	reg &= ~IMPCAL_VTH_MASK;
+	reg |= IMPCAL_VTH_VAL << IMPCAL_VTH_OFFSET;
+	writel(reg, PORT_REGS(port) + UTMI_CAL_CTRL_REG);
+
+	/* Set LS TX driver strength coarse control */
+	reg = readl(PORT_REGS(port) + UTMI_TX_CH_CTRL_REG);
+	reg &= ~TX_AMP_MASK;
+	reg |= TX_AMP_VAL << TX_AMP_OFFSET;
+	writel(reg, PORT_REGS(port) + UTMI_TX_CH_CTRL_REG);
+
+	/* Disable SQ and enable analog squelch detect */
+	reg = readl(PORT_REGS(port) + UTMI_RX_CH_CTRL0_REG);
+	reg &= ~SQ_DET_EN;
+	reg |= SQ_ANA_DTC_SEL;
+	writel(reg, PORT_REGS(port) + UTMI_RX_CH_CTRL0_REG);
+
+	/*
+	 * Set External squelch calibration number and
+	 * enable the External squelch calibration
+	 */
+	reg = readl(PORT_REGS(port) + UTMI_RX_CH_CTRL1_REG);
+	reg &= ~SQ_AMP_CAL_MASK;
+	reg |= (SQ_AMP_CAL_VAL << SQ_AMP_CAL_OFFSET) | SQ_AMP_CAL_EN;
+	writel(reg, PORT_REGS(port) + UTMI_RX_CH_CTRL1_REG);
+
+	/*
+	 * Set Control VDAT Reference Voltage - 0.325V and
+	 * Control VSRC Reference Voltage - 0.6V
+	 */
+	reg = readl(PORT_REGS(port) + UTMI_CHGDTC_CTRL_REG);
+	reg &= ~(VDAT_MASK | VSRC_MASK);
+	reg |= (VDAT_VAL << VDAT_OFFSET) | (VSRC_VAL << VSRC_OFFSET);
+	writel(reg, PORT_REGS(port) + UTMI_CHGDTC_CTRL_REG);
+}
+
+static int mvebu_cp110_utmi_phy_power_off(struct phy *phy)
+{
+	struct mvebu_cp110_utmi_port *port = phy_get_drvdata(phy);
+	struct mvebu_cp110_utmi *utmi = port->priv;
+	int i;
+
+	/* Power down UTMI PHY port */
+	regmap_clear_bits(utmi->syscon, SYSCON_UTMI_CFG_REG(port->id),
+			  UTMI_PHY_CFG_PU_MASK);
+
+	for (i = 0; i < UTMI_PHY_PORTS; i++) {
+		int test = regmap_test_bits(utmi->syscon,
+					    SYSCON_UTMI_CFG_REG(i),
+					    UTMI_PHY_CFG_PU_MASK);
+		/* skip PLL shutdown if there are active UTMI PHY ports */
+		if (test != 0)
+			return 0;
+	}
+
+	/* PLL Power down if all UTMI PHYs are down */
+	regmap_clear_bits(utmi->syscon, SYSCON_USB_CFG_REG, USB_CFG_PLL_MASK);
+
+	return 0;
+}
+
+static int mvebu_cp110_utmi_phy_power_on(struct phy *phy)
+{
+	struct mvebu_cp110_utmi_port *port = phy_get_drvdata(phy);
+	struct mvebu_cp110_utmi *utmi = port->priv;
+	struct device *dev = &phy->dev;
+	int ret;
+	u32 reg;
+
+	/* It is necessary to power off UTMI before configuration */
+	ret = mvebu_cp110_utmi_phy_power_off(phy);
+	if (ret) {
+		dev_err(dev, "UTMI power OFF before power ON failed\n");
+		return ret;
+	}
+
+	/*
+	 * If UTMI port is connected to USB Device controller,
+	 * configure the USB MUX prior to UTMI PHY initialization.
+	 * The single USB device controller can be connected
+	 * to UTMI0 or to UTMI1 PHY port, but not to both.
+	 */
+	if (port->dr_mode == USB_DR_MODE_PERIPHERAL) {
+		regmap_update_bits(utmi->syscon, SYSCON_USB_CFG_REG,
+				   USB_CFG_DEVICE_EN_MASK | USB_CFG_DEVICE_MUX_MASK,
+				   USB_CFG_DEVICE_EN_MASK |
+				   (port->id << USB_CFG_DEVICE_MUX_OFFSET));
+	}
+
+	/* Set Test suspendm mode and enable Test UTMI select */
+	reg = readl(PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
+	reg |= SUSPENDM | TEST_SEL;
+	writel(reg, PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
+
+	/* Wait for UTMI power down */
+	mdelay(1);
+
+	/* PHY port setup first */
+	mvebu_cp110_utmi_port_setup(port);
+
+	/* Power UP UTMI PHY */
+	regmap_set_bits(utmi->syscon, SYSCON_UTMI_CFG_REG(port->id),
+			UTMI_PHY_CFG_PU_MASK);
+
+	/* Disable Test UTMI select */
+	reg = readl(PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
+	reg &= ~TEST_SEL;
+	writel(reg, PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
+
+	/* Wait for impedance calibration */
+	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_CAL_CTRL_REG, reg,
+				 reg & IMPCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end UTMI impedance calibration\n");
+		return ret;
+	}
+
+	/* Wait for PLL calibration */
+	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_CAL_CTRL_REG, reg,
+				 reg & PLLCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end UTMI PLL calibration\n");
+		return ret;
+	}
+
+	/* Wait for PLL ready */
+	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_PLL_CTRL_REG, reg,
+				 reg & PLL_RDY,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "PLL is not ready\n");
+		return ret;
+	}
+
+	/* PLL Power up */
+	regmap_set_bits(utmi->syscon, SYSCON_USB_CFG_REG, USB_CFG_PLL_MASK);
+
+	return 0;
+}
+
+static const struct phy_ops mvebu_cp110_utmi_phy_ops = {
+	.power_on = mvebu_cp110_utmi_phy_power_on,
+	.power_off = mvebu_cp110_utmi_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static const struct of_device_id mvebu_cp110_utmi_of_match[] = {
+	{ .compatible = "marvell,cp110-utmi-phy" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, mvebu_cp110_utmi_of_match);
+
+static int mvebu_cp110_utmi_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mvebu_cp110_utmi *utmi;
+	struct phy_provider *provider;
+	struct device_node *child;
+	u32 usb_devices = 0;
+
+	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
+	if (!utmi)
+		return -ENOMEM;
+
+	utmi->dev = dev;
+
+	/* Get system controller region */
+	utmi->syscon = syscon_regmap_lookup_by_phandle(dev->of_node,
+						       "marvell,system-controller");
+	if (IS_ERR(utmi->syscon)) {
+		dev_err(dev, "Missing UTMI system controller\n");
+		return PTR_ERR(utmi->syscon);
+	}
+
+	/* Get UTMI memory region */
+	utmi->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(utmi->regs))
+		return PTR_ERR(utmi->regs);
+
+	for_each_available_child_of_node(dev->of_node, child) {
+		struct mvebu_cp110_utmi_port *port;
+		struct phy *phy;
+		int ret;
+		u32 port_id;
+
+		ret = of_property_read_u32(child, "reg", &port_id);
+		if ((ret < 0) || (port_id >= UTMI_PHY_PORTS)) {
+			dev_err(dev,
+				"invalid 'reg' property on child %pOF\n",
+				child);
+			continue;
+		}
+
+		port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+		if (!port) {
+			of_node_put(child);
+			return -ENOMEM;
+		}
+
+		port->dr_mode = of_usb_get_dr_mode_by_phy(child, -1);
+		if ((port->dr_mode != USB_DR_MODE_HOST) &&
+		    (port->dr_mode != USB_DR_MODE_PERIPHERAL)) {
+			dev_err(&pdev->dev,
+				"Missing dual role setting of the port%d, will use HOST mode\n",
+				port_id);
+			port->dr_mode = USB_DR_MODE_HOST;
+		}
+
+		if (port->dr_mode == USB_DR_MODE_PERIPHERAL) {
+			usb_devices++;
+			if (usb_devices > 1) {
+				dev_err(dev,
+					"Single USB device allowed! Port%d will use HOST mode\n",
+					port_id);
+				port->dr_mode = USB_DR_MODE_HOST;
+			}
+		}
+
+		/* Retrieve PHY capabilities */
+		utmi->ops = &mvebu_cp110_utmi_phy_ops;
+
+		/* Instantiate the PHY */
+		phy = devm_phy_create(dev, child, utmi->ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "Failed to create the UTMI PHY\n");
+			of_node_put(child);
+			return PTR_ERR(phy);
+		}
+
+		port->priv = utmi;
+		port->id = port_id;
+		phy_set_drvdata(phy, port);
+
+		/* Ensure the PHY is powered off */
+		mvebu_cp110_utmi_phy_power_off(phy);
+	}
+
+	dev_set_drvdata(dev, utmi);
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static struct platform_driver mvebu_cp110_utmi_driver = {
+	.probe	= mvebu_cp110_utmi_phy_probe,
+	.driver	= {
+		.name		= "mvebu-cp110-utmi-phy",
+		.of_match_table	= mvebu_cp110_utmi_of_match,
+	 },
+};
+module_platform_driver(mvebu_cp110_utmi_driver);
+
+MODULE_AUTHOR("Konstatin Porotchkin <kostap@marvell.com>");
+MODULE_DESCRIPTION("Marvell Armada CP110 UTMI PHY driver");
+MODULE_LICENSE("GPL v2");