Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 606 insertions, 0 deletions

diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
new file mode 100644
index 000000000..704435526
--- /dev/null
+++ b/drivers/usb/musb/davinci.c
@@ -0,0 +1,606 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2005-2006 by Texas Instruments
+ *
+ * This file is part of the Inventra Controller Driver for Linux.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/list.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/usb/usb_phy_generic.h>
+
+#include <mach/cputype.h>
+#include <mach/hardware.h>
+
+#include <asm/mach-types.h>
+
+#include "musb_core.h"
+
+#include "davinci.h"
+#include "cppi_dma.h"
+
+
+#define USB_PHY_CTRL	IO_ADDRESS(USBPHY_CTL_PADDR)
+#define DM355_DEEPSLEEP	IO_ADDRESS(DM355_DEEPSLEEP_PADDR)
+
+struct davinci_glue {
+	struct device		*dev;
+	struct platform_device	*musb;
+	struct clk		*clk;
+	bool			vbus_state;
+	struct gpio_desc	*vbus;
+	struct work_struct	vbus_work;
+};
+
+/* REVISIT (PM) we should be able to keep the PHY in low power mode most
+ * of the time (24 MHZ oscillator and PLL off, etc) by setting POWER.D0
+ * and, when in host mode, autosuspending idle root ports... PHYPLLON
+ * (overriding SUSPENDM?) then likely needs to stay off.
+ */
+
+static inline void phy_on(void)
+{
+	u32	phy_ctrl = __raw_readl(USB_PHY_CTRL);
+
+	/* power everything up; start the on-chip PHY and its PLL */
+	phy_ctrl &= ~(USBPHY_OSCPDWN | USBPHY_OTGPDWN | USBPHY_PHYPDWN);
+	phy_ctrl |= USBPHY_SESNDEN | USBPHY_VBDTCTEN | USBPHY_PHYPLLON;
+	__raw_writel(phy_ctrl, USB_PHY_CTRL);
+
+	/* wait for PLL to lock before proceeding */
+	while ((__raw_readl(USB_PHY_CTRL) & USBPHY_PHYCLKGD) == 0)
+		cpu_relax();
+}
+
+static inline void phy_off(void)
+{
+	u32	phy_ctrl = __raw_readl(USB_PHY_CTRL);
+
+	/* powerdown the on-chip PHY, its PLL, and the OTG block */
+	phy_ctrl &= ~(USBPHY_SESNDEN | USBPHY_VBDTCTEN | USBPHY_PHYPLLON);
+	phy_ctrl |= USBPHY_OSCPDWN | USBPHY_OTGPDWN | USBPHY_PHYPDWN;
+	__raw_writel(phy_ctrl, USB_PHY_CTRL);
+}
+
+static int dma_off = 1;
+
+static void davinci_musb_enable(struct musb *musb)
+{
+	u32	tmp, old, val;
+
+	/* workaround:  setup irqs through both register sets */
+	tmp = (musb->epmask & DAVINCI_USB_TX_ENDPTS_MASK)
+			<< DAVINCI_USB_TXINT_SHIFT;
+	musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp);
+	old = tmp;
+	tmp = (musb->epmask & (0xfffe & DAVINCI_USB_RX_ENDPTS_MASK))
+			<< DAVINCI_USB_RXINT_SHIFT;
+	musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp);
+	tmp |= old;
+
+	val = ~MUSB_INTR_SOF;
+	tmp |= ((val & 0x01ff) << DAVINCI_USB_USBINT_SHIFT);
+	musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp);
+
+	if (is_dma_capable() && !dma_off)
+		printk(KERN_WARNING "%s %s: dma not reactivated\n",
+				__FILE__, __func__);
+	else
+		dma_off = 0;
+
+	/* force a DRVVBUS irq so we can start polling for ID change */
+	musb_writel(musb->ctrl_base, DAVINCI_USB_INT_SET_REG,
+			DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT);
+}
+
+/*
+ * Disable the HDRC and flush interrupts
+ */
+static void davinci_musb_disable(struct musb *musb)
+{
+	/* because we don't set CTRLR.UINT, "important" to:
+	 *  - not read/write INTRUSB/INTRUSBE
+	 *  - (except during initial setup, as workaround)
+	 *  - use INTSETR/INTCLRR instead
+	 */
+	musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_CLR_REG,
+			  DAVINCI_USB_USBINT_MASK
+			| DAVINCI_USB_TXINT_MASK
+			| DAVINCI_USB_RXINT_MASK);
+	musb_writel(musb->ctrl_base, DAVINCI_USB_EOI_REG, 0);
+
+	if (is_dma_capable() && !dma_off)
+		WARNING("dma still active\n");
+}
+
+
+#define	portstate(stmt)		stmt
+
+/*
+ * VBUS SWITCHING IS BOARD-SPECIFIC ... at least for the DM6446 EVM,
+ * which doesn't wire DRVVBUS to the FET that switches it.  Unclear
+ * if that's a problem with the DM6446 chip or just with that board.
+ *
+ * In either case, the DM355 EVM automates DRVVBUS the normal way,
+ * when J10 is out, and TI documents it as handling OTG.
+ */
+
+/* I2C operations are always synchronous, and require a task context.
+ * With unloaded systems, using the shared workqueue seems to suffice
+ * to satisfy the 100msec A_WAIT_VRISE timeout...
+ */
+static void evm_deferred_drvvbus(struct work_struct *work)
+{
+	struct davinci_glue *glue = container_of(work, struct davinci_glue,
+						 vbus_work);
+
+	gpiod_set_value_cansleep(glue->vbus, glue->vbus_state);
+	glue->vbus_state = !glue->vbus_state;
+}
+
+static void davinci_musb_source_power(struct musb *musb, int is_on,
+				      int immediate)
+{
+	struct davinci_glue *glue = dev_get_drvdata(musb->controller->parent);
+
+	/* This GPIO handling is entirely optional */
+	if (!glue->vbus)
+		return;
+
+	if (is_on)
+		is_on = 1;
+
+	if (glue->vbus_state == is_on)
+		return;
+	/* 0/1 vs "-1 == unknown/init" */
+	glue->vbus_state = !is_on;
+
+	if (machine_is_davinci_evm()) {
+		if (immediate)
+			gpiod_set_value_cansleep(glue->vbus, glue->vbus_state);
+		else
+			schedule_work(&glue->vbus_work);
+	}
+	if (immediate)
+		glue->vbus_state = is_on;
+}
+
+static void davinci_musb_set_vbus(struct musb *musb, int is_on)
+{
+	WARN_ON(is_on && is_peripheral_active(musb));
+	davinci_musb_source_power(musb, is_on, 0);
+}
+
+
+#define	POLL_SECONDS	2
+
+static void otg_timer(struct timer_list *t)
+{
+	struct musb		*musb = from_timer(musb, t, dev_timer);
+	void __iomem		*mregs = musb->mregs;
+	u8			devctl;
+	unsigned long		flags;
+
+	/* We poll because DaVinci's won't expose several OTG-critical
+	* status change events (from the transceiver) otherwise.
+	 */
+	devctl = musb_readb(mregs, MUSB_DEVCTL);
+	dev_dbg(musb->controller, "poll devctl %02x (%s)\n", devctl,
+		usb_otg_state_string(musb->xceiv->otg->state));
+
+	spin_lock_irqsave(&musb->lock, flags);
+	switch (musb->xceiv->otg->state) {
+	case OTG_STATE_A_WAIT_VFALL:
+		/* Wait till VBUS falls below SessionEnd (~0.2V); the 1.3 RTL
+		 * seems to mis-handle session "start" otherwise (or in our
+		 * case "recover"), in routine "VBUS was valid by the time
+		 * VBUSERR got reported during enumeration" cases.
+		 */
+		if (devctl & MUSB_DEVCTL_VBUS) {
+			mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
+			break;
+		}
+		musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
+		musb_writel(musb->ctrl_base, DAVINCI_USB_INT_SET_REG,
+			MUSB_INTR_VBUSERROR << DAVINCI_USB_USBINT_SHIFT);
+		break;
+	case OTG_STATE_B_IDLE:
+		/*
+		 * There's no ID-changed IRQ, so we have no good way to tell
+		 * when to switch to the A-Default state machine (by setting
+		 * the DEVCTL.SESSION flag).
+		 *
+		 * Workaround:  whenever we're in B_IDLE, try setting the
+		 * session flag every few seconds.  If it works, ID was
+		 * grounded and we're now in the A-Default state machine.
+		 *
+		 * NOTE setting the session flag is _supposed_ to trigger
+		 * SRP, but clearly it doesn't.
+		 */
+		musb_writeb(mregs, MUSB_DEVCTL,
+				devctl | MUSB_DEVCTL_SESSION);
+		devctl = musb_readb(mregs, MUSB_DEVCTL);
+		if (devctl & MUSB_DEVCTL_BDEVICE)
+			mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
+		else
+			musb->xceiv->otg->state = OTG_STATE_A_IDLE;
+		break;
+	default:
+		break;
+	}
+	spin_unlock_irqrestore(&musb->lock, flags);
+}
+
+static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
+{
+	unsigned long	flags;
+	irqreturn_t	retval = IRQ_NONE;
+	struct musb	*musb = __hci;
+	struct usb_otg	*otg = musb->xceiv->otg;
+	void __iomem	*tibase = musb->ctrl_base;
+	struct cppi	*cppi;
+	u32		tmp;
+
+	spin_lock_irqsave(&musb->lock, flags);
+
+	/* NOTE: DaVinci shadows the Mentor IRQs.  Don't manage them through
+	 * the Mentor registers (except for setup), use the TI ones and EOI.
+	 *
+	 * Docs describe irq "vector" registers associated with the CPPI and
+	 * USB EOI registers.  These hold a bitmask corresponding to the
+	 * current IRQ, not an irq handler address.  Would using those bits
+	 * resolve some of the races observed in this dispatch code??
+	 */
+
+	/* CPPI interrupts share the same IRQ line, but have their own
+	 * mask, state, "vector", and EOI registers.
+	 */
+	cppi = container_of(musb->dma_controller, struct cppi, controller);
+	if (is_cppi_enabled(musb) && musb->dma_controller && !cppi->irq)
+		retval = cppi_interrupt(irq, __hci);
+
+	/* ack and handle non-CPPI interrupts */
+	tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
+	musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
+	dev_dbg(musb->controller, "IRQ %08x\n", tmp);
+
+	musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
+			>> DAVINCI_USB_RXINT_SHIFT;
+	musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
+			>> DAVINCI_USB_TXINT_SHIFT;
+	musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
+			>> DAVINCI_USB_USBINT_SHIFT;
+
+	/* DRVVBUS irqs are the only proxy we have (a very poor one!) for
+	 * DaVinci's missing ID change IRQ.  We need an ID change IRQ to
+	 * switch appropriately between halves of the OTG state machine.
+	 * Managing DEVCTL.SESSION per Mentor docs requires we know its
+	 * value, but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
+	 * Also, DRVVBUS pulses for SRP (but not at 5V) ...
+	 */
+	if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) {
+		int	drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
+		void __iomem *mregs = musb->mregs;
+		u8	devctl = musb_readb(mregs, MUSB_DEVCTL);
+		int	err = musb->int_usb & MUSB_INTR_VBUSERROR;
+
+		err = musb->int_usb & MUSB_INTR_VBUSERROR;
+		if (err) {
+			/* The Mentor core doesn't debounce VBUS as needed
+			 * to cope with device connect current spikes. This
+			 * means it's not uncommon for bus-powered devices
+			 * to get VBUS errors during enumeration.
+			 *
+			 * This is a workaround, but newer RTL from Mentor
+			 * seems to allow a better one: "re"starting sessions
+			 * without waiting (on EVM, a **long** time) for VBUS
+			 * to stop registering in devctl.
+			 */
+			musb->int_usb &= ~MUSB_INTR_VBUSERROR;
+			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
+			mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
+			WARNING("VBUS error workaround (delay coming)\n");
+		} else if (drvvbus) {
+			MUSB_HST_MODE(musb);
+			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
+			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
+			del_timer(&musb->dev_timer);
+		} else {
+			musb->is_active = 0;
+			MUSB_DEV_MODE(musb);
+			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
+			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
+		}
+
+		/* NOTE:  this must complete poweron within 100 msec
+		 * (OTG_TIME_A_WAIT_VRISE) but we don't check for that.
+		 */
+		davinci_musb_source_power(musb, drvvbus, 0);
+		dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
+				drvvbus ? "on" : "off",
+				usb_otg_state_string(musb->xceiv->otg->state),
+				err ? " ERROR" : "",
+				devctl);
+		retval = IRQ_HANDLED;
+	}
+
+	if (musb->int_tx || musb->int_rx || musb->int_usb)
+		retval |= musb_interrupt(musb);
+
+	/* irq stays asserted until EOI is written */
+	musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
+
+	/* poll for ID change */
+	if (musb->xceiv->otg->state == OTG_STATE_B_IDLE)
+		mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
+
+	spin_unlock_irqrestore(&musb->lock, flags);
+
+	return retval;
+}
+
+static int davinci_musb_set_mode(struct musb *musb, u8 mode)
+{
+	/* EVM can't do this (right?) */
+	return -EIO;
+}
+
+static int davinci_musb_init(struct musb *musb)
+{
+	void __iomem	*tibase = musb->ctrl_base;
+	u32		revision;
+	int 		ret = -ENODEV;
+
+	musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
+	if (IS_ERR_OR_NULL(musb->xceiv)) {
+		ret = -EPROBE_DEFER;
+		goto unregister;
+	}
+
+	musb->mregs += DAVINCI_BASE_OFFSET;
+
+	/* returns zero if e.g. not clocked */
+	revision = musb_readl(tibase, DAVINCI_USB_VERSION_REG);
+	if (revision == 0)
+		goto fail;
+
+	timer_setup(&musb->dev_timer, otg_timer, 0);
+
+	davinci_musb_source_power(musb, 0, 1);
+
+	/* dm355 EVM swaps D+/D- for signal integrity, and
+	 * is clocked from the main 24 MHz crystal.
+	 */
+	if (machine_is_davinci_dm355_evm()) {
+		u32	phy_ctrl = __raw_readl(USB_PHY_CTRL);
+
+		phy_ctrl &= ~(3 << 9);
+		phy_ctrl |= USBPHY_DATAPOL;
+		__raw_writel(phy_ctrl, USB_PHY_CTRL);
+	}
+
+	/* On dm355, the default-A state machine needs DRVVBUS control.
+	 * If we won't be a host, there's no need to turn it on.
+	 */
+	if (cpu_is_davinci_dm355()) {
+		u32	deepsleep = __raw_readl(DM355_DEEPSLEEP);
+
+		deepsleep &= ~DRVVBUS_FORCE;
+		__raw_writel(deepsleep, DM355_DEEPSLEEP);
+	}
+
+	/* reset the controller */
+	musb_writel(tibase, DAVINCI_USB_CTRL_REG, 0x1);
+
+	/* start the on-chip PHY and its PLL */
+	phy_on();
+
+	msleep(5);
+
+	/* NOTE:  irqs are in mixed mode, not bypass to pure-musb */
+	pr_debug("DaVinci OTG revision %08x phy %03x control %02x\n",
+		revision, __raw_readl(USB_PHY_CTRL),
+		musb_readb(tibase, DAVINCI_USB_CTRL_REG));
+
+	musb->isr = davinci_musb_interrupt;
+	return 0;
+
+fail:
+	usb_put_phy(musb->xceiv);
+unregister:
+	usb_phy_generic_unregister();
+	return ret;
+}
+
+static int davinci_musb_exit(struct musb *musb)
+{
+	int	maxdelay = 30;
+	u8	devctl, warn = 0;
+
+	del_timer_sync(&musb->dev_timer);
+
+	/* force VBUS off */
+	if (cpu_is_davinci_dm355()) {
+		u32	deepsleep = __raw_readl(DM355_DEEPSLEEP);
+
+		deepsleep &= ~DRVVBUS_FORCE;
+		deepsleep |= DRVVBUS_OVERRIDE;
+		__raw_writel(deepsleep, DM355_DEEPSLEEP);
+	}
+
+	davinci_musb_source_power(musb, 0 /*off*/, 1);
+
+	/*
+	 * delay, to avoid problems with module reload.
+	 * if there's no peripheral connected, this can take a
+	 * long time to fall, especially on EVM with huge C133.
+	 */
+	do {
+		devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
+		if (!(devctl & MUSB_DEVCTL_VBUS))
+			break;
+		if ((devctl & MUSB_DEVCTL_VBUS) != warn) {
+			warn = devctl & MUSB_DEVCTL_VBUS;
+			dev_dbg(musb->controller, "VBUS %d\n",
+				warn >> MUSB_DEVCTL_VBUS_SHIFT);
+		}
+		msleep(1000);
+		maxdelay--;
+	} while (maxdelay > 0);
+
+	/* in OTG mode, another host might be connected */
+	if (devctl & MUSB_DEVCTL_VBUS)
+		dev_dbg(musb->controller, "VBUS off timeout (devctl %02x)\n", devctl);
+
+	phy_off();
+
+	usb_put_phy(musb->xceiv);
+
+	return 0;
+}
+
+static const struct musb_platform_ops davinci_ops = {
+	.quirks		= MUSB_DMA_CPPI,
+	.init		= davinci_musb_init,
+	.exit		= davinci_musb_exit,
+
+#ifdef CONFIG_USB_TI_CPPI_DMA
+	.dma_init	= cppi_dma_controller_create,
+	.dma_exit	= cppi_dma_controller_destroy,
+#endif
+	.enable		= davinci_musb_enable,
+	.disable	= davinci_musb_disable,
+
+	.set_mode	= davinci_musb_set_mode,
+
+	.set_vbus	= davinci_musb_set_vbus,
+};
+
+static const struct platform_device_info davinci_dev_info = {
+	.name		= "musb-hdrc",
+	.id		= PLATFORM_DEVID_AUTO,
+	.dma_mask	= DMA_BIT_MASK(32),
+};
+
+static int davinci_probe(struct platform_device *pdev)
+{
+	struct resource			musb_resources[3];
+	struct musb_hdrc_platform_data	*pdata = dev_get_platdata(&pdev->dev);
+	struct platform_device		*musb;
+	struct davinci_glue		*glue;
+	struct platform_device_info	pinfo;
+	struct clk			*clk;
+
+	int				ret = -ENOMEM;
+
+	glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
+	if (!glue)
+		goto err0;
+
+	clk = devm_clk_get(&pdev->dev, "usb");
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed to get clock\n");
+		ret = PTR_ERR(clk);
+		goto err0;
+	}
+
+	ret = clk_enable(clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable clock\n");
+		goto err0;
+	}
+
+	glue->dev			= &pdev->dev;
+	glue->clk			= clk;
+
+	pdata->platform_ops		= &davinci_ops;
+
+	glue->vbus = devm_gpiod_get_optional(&pdev->dev, NULL, GPIOD_OUT_LOW);
+	if (IS_ERR(glue->vbus)) {
+		ret = PTR_ERR(glue->vbus);
+		goto err0;
+	} else {
+		glue->vbus_state = -1;
+		INIT_WORK(&glue->vbus_work, evm_deferred_drvvbus);
+	}
+
+	usb_phy_generic_register();
+	platform_set_drvdata(pdev, glue);
+
+	memset(musb_resources, 0x00, sizeof(*musb_resources) *
+			ARRAY_SIZE(musb_resources));
+
+	musb_resources[0].name = pdev->resource[0].name;
+	musb_resources[0].start = pdev->resource[0].start;
+	musb_resources[0].end = pdev->resource[0].end;
+	musb_resources[0].flags = pdev->resource[0].flags;
+
+	musb_resources[1].name = pdev->resource[1].name;
+	musb_resources[1].start = pdev->resource[1].start;
+	musb_resources[1].end = pdev->resource[1].end;
+	musb_resources[1].flags = pdev->resource[1].flags;
+
+	/*
+	 * For DM6467 3 resources are passed. A placeholder for the 3rd
+	 * resource is always there, so it's safe to always copy it...
+	 */
+	musb_resources[2].name = pdev->resource[2].name;
+	musb_resources[2].start = pdev->resource[2].start;
+	musb_resources[2].end = pdev->resource[2].end;
+	musb_resources[2].flags = pdev->resource[2].flags;
+
+	pinfo = davinci_dev_info;
+	pinfo.parent = &pdev->dev;
+	pinfo.res = musb_resources;
+	pinfo.num_res = ARRAY_SIZE(musb_resources);
+	pinfo.data = pdata;
+	pinfo.size_data = sizeof(*pdata);
+
+	glue->musb = musb = platform_device_register_full(&pinfo);
+	if (IS_ERR(musb)) {
+		ret = PTR_ERR(musb);
+		dev_err(&pdev->dev, "failed to register musb device: %d\n", ret);
+		goto err1;
+	}
+
+	return 0;
+
+err1:
+	clk_disable(clk);
+
+err0:
+	return ret;
+}
+
+static int davinci_remove(struct platform_device *pdev)
+{
+	struct davinci_glue		*glue = platform_get_drvdata(pdev);
+
+	platform_device_unregister(glue->musb);
+	usb_phy_generic_unregister();
+	clk_disable(glue->clk);
+
+	return 0;
+}
+
+static struct platform_driver davinci_driver = {
+	.probe		= davinci_probe,
+	.remove		= davinci_remove,
+	.driver		= {
+		.name	= "musb-davinci",
+	},
+};
+
+MODULE_DESCRIPTION("DaVinci MUSB Glue Layer");
+MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
+MODULE_LICENSE("GPL v2");
+module_platform_driver(davinci_driver);