diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 7025 |
1 files changed, 7025 insertions, 0 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt new file mode 100644 index 000000000..4ad60e127 --- /dev/null +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -0,0 +1,7025 @@ + acpi= [HW,ACPI,X86,ARM64] + Advanced Configuration and Power Interface + Format: { force | on | off | strict | noirq | rsdt | + copy_dsdt } + force -- enable ACPI if default was off + on -- enable ACPI but allow fallback to DT [arm64] + off -- disable ACPI if default was on + noirq -- do not use ACPI for IRQ routing + strict -- Be less tolerant of platforms that are not + strictly ACPI specification compliant. + rsdt -- prefer RSDT over (default) XSDT + copy_dsdt -- copy DSDT to memory + For ARM64, ONLY "acpi=off", "acpi=on" or "acpi=force" + are available + + See also Documentation/power/runtime_pm.rst, pci=noacpi + + acpi_apic_instance= [ACPI, IOAPIC] + Format: <int> + 2: use 2nd APIC table, if available + 1,0: use 1st APIC table + default: 0 + + acpi_backlight= [HW,ACPI] + { vendor | video | native | none } + If set to vendor, prefer vendor-specific driver + (e.g. thinkpad_acpi, sony_acpi, etc.) instead + of the ACPI video.ko driver. + If set to video, use the ACPI video.ko driver. + If set to native, use the device's native backlight mode. + If set to none, disable the ACPI backlight interface. + + acpi_force_32bit_fadt_addr + force FADT to use 32 bit addresses rather than the + 64 bit X_* addresses. Some firmware have broken 64 + bit addresses for force ACPI ignore these and use + the older legacy 32 bit addresses. + + acpica_no_return_repair [HW, ACPI] + Disable AML predefined validation mechanism + This mechanism can repair the evaluation result to make + the return objects more ACPI specification compliant. + This option is useful for developers to identify the + root cause of an AML interpreter issue when the issue + has something to do with the repair mechanism. + + acpi.debug_layer= [HW,ACPI,ACPI_DEBUG] + acpi.debug_level= [HW,ACPI,ACPI_DEBUG] + Format: <int> + CONFIG_ACPI_DEBUG must be enabled to produce any ACPI + debug output. Bits in debug_layer correspond to a + _COMPONENT in an ACPI source file, e.g., + #define _COMPONENT ACPI_EVENTS + Bits in debug_level correspond to a level in + ACPI_DEBUG_PRINT statements, e.g., + ACPI_DEBUG_PRINT((ACPI_DB_INFO, ... + The debug_level mask defaults to "info". See + Documentation/firmware-guide/acpi/debug.rst for more information about + debug layers and levels. + + Enable processor driver info messages: + acpi.debug_layer=0x20000000 + Enable AML "Debug" output, i.e., stores to the Debug + object while interpreting AML: + acpi.debug_layer=0xffffffff acpi.debug_level=0x2 + Enable all messages related to ACPI hardware: + acpi.debug_layer=0x2 acpi.debug_level=0xffffffff + + Some values produce so much output that the system is + unusable. The "log_buf_len" parameter may be useful + if you need to capture more output. + + acpi_enforce_resources= [ACPI] + { strict | lax | no } + Check for resource conflicts between native drivers + and ACPI OperationRegions (SystemIO and SystemMemory + only). IO ports and memory declared in ACPI might be + used by the ACPI subsystem in arbitrary AML code and + can interfere with legacy drivers. + strict (default): access to resources claimed by ACPI + is denied; legacy drivers trying to access reserved + resources will fail to bind to device using them. + lax: access to resources claimed by ACPI is allowed; + legacy drivers trying to access reserved resources + will bind successfully but a warning message is logged. + no: ACPI OperationRegions are not marked as reserved, + no further checks are performed. + + acpi_force_table_verification [HW,ACPI] + Enable table checksum verification during early stage. + By default, this is disabled due to x86 early mapping + size limitation. + + acpi_irq_balance [HW,ACPI] + ACPI will balance active IRQs + default in APIC mode + + acpi_irq_nobalance [HW,ACPI] + ACPI will not move active IRQs (default) + default in PIC mode + + acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA + Format: <irq>,<irq>... + + acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for + use by PCI + Format: <irq>,<irq>... + + acpi_mask_gpe= [HW,ACPI] + Due to the existence of _Lxx/_Exx, some GPEs triggered + by unsupported hardware/firmware features can result in + GPE floodings that cannot be automatically disabled by + the GPE dispatcher. + This facility can be used to prevent such uncontrolled + GPE floodings. + Format: <byte> or <bitmap-list> + + acpi_no_auto_serialize [HW,ACPI] + Disable auto-serialization of AML methods + AML control methods that contain the opcodes to create + named objects will be marked as "Serialized" by the + auto-serialization feature. + This feature is enabled by default. + This option allows to turn off the feature. + + acpi_no_memhotplug [ACPI] Disable memory hotplug. Useful for kdump + kernels. + + acpi_no_static_ssdt [HW,ACPI] + Disable installation of static SSDTs at early boot time + By default, SSDTs contained in the RSDT/XSDT will be + installed automatically and they will appear under + /sys/firmware/acpi/tables. + This option turns off this feature. + Note that specifying this option does not affect + dynamic table installation which will install SSDT + tables to /sys/firmware/acpi/tables/dynamic. + + acpi_no_watchdog [HW,ACPI,WDT] + Ignore the ACPI-based watchdog interface (WDAT) and let + a native driver control the watchdog device instead. + + acpi_rsdp= [ACPI,EFI,KEXEC] + Pass the RSDP address to the kernel, mostly used + on machines running EFI runtime service to boot the + second kernel for kdump. + + acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS + Format: To spoof as Windows 98: ="Microsoft Windows" + + acpi_rev_override [ACPI] Override the _REV object to return 5 (instead + of 2 which is mandated by ACPI 6) as the supported ACPI + specification revision (when using this switch, it may + be necessary to carry out a cold reboot _twice_ in a + row to make it take effect on the platform firmware). + + acpi_osi= [HW,ACPI] Modify list of supported OS interface strings + acpi_osi="string1" # add string1 + acpi_osi="!string2" # remove string2 + acpi_osi=!* # remove all strings + acpi_osi=! # disable all built-in OS vendor + strings + acpi_osi=!! # enable all built-in OS vendor + strings + acpi_osi= # disable all strings + + 'acpi_osi=!' can be used in combination with single or + multiple 'acpi_osi="string1"' to support specific OS + vendor string(s). Note that such command can only + affect the default state of the OS vendor strings, thus + it cannot affect the default state of the feature group + strings and the current state of the OS vendor strings, + specifying it multiple times through kernel command line + is meaningless. This command is useful when one do not + care about the state of the feature group strings which + should be controlled by the OSPM. + Examples: + 1. 'acpi_osi=! acpi_osi="Windows 2000"' is equivalent + to 'acpi_osi="Windows 2000" acpi_osi=!', they all + can make '_OSI("Windows 2000")' TRUE. + + 'acpi_osi=' cannot be used in combination with other + 'acpi_osi=' command lines, the _OSI method will not + exist in the ACPI namespace. NOTE that such command can + only affect the _OSI support state, thus specifying it + multiple times through kernel command line is also + meaningless. + Examples: + 1. 'acpi_osi=' can make 'CondRefOf(_OSI, Local1)' + FALSE. + + 'acpi_osi=!*' can be used in combination with single or + multiple 'acpi_osi="string1"' to support specific + string(s). Note that such command can affect the + current state of both the OS vendor strings and the + feature group strings, thus specifying it multiple times + through kernel command line is meaningful. But it may + still not able to affect the final state of a string if + there are quirks related to this string. This command + is useful when one want to control the state of the + feature group strings to debug BIOS issues related to + the OSPM features. + Examples: + 1. 'acpi_osi="Module Device" acpi_osi=!*' can make + '_OSI("Module Device")' FALSE. + 2. 'acpi_osi=!* acpi_osi="Module Device"' can make + '_OSI("Module Device")' TRUE. + 3. 'acpi_osi=! acpi_osi=!* acpi_osi="Windows 2000"' is + equivalent to + 'acpi_osi=!* acpi_osi=! acpi_osi="Windows 2000"' + and + 'acpi_osi=!* acpi_osi="Windows 2000" acpi_osi=!', + they all will make '_OSI("Windows 2000")' TRUE. + + acpi_pm_good [X86] + Override the pmtimer bug detection: force the kernel + to assume that this machine's pmtimer latches its value + and always returns good values. + + acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode + Format: { level | edge | high | low } + + acpi_skip_timer_override [HW,ACPI] + Recognize and ignore IRQ0/pin2 Interrupt Override. + For broken nForce2 BIOS resulting in XT-PIC timer. + + acpi_sleep= [HW,ACPI] Sleep options + Format: { s3_bios, s3_mode, s3_beep, s4_hwsig, + s4_nohwsig, old_ordering, nonvs, + sci_force_enable, nobl } + See Documentation/power/video.rst for information on + s3_bios and s3_mode. + s3_beep is for debugging; it makes the PC's speaker beep + as soon as the kernel's real-mode entry point is called. + s4_hwsig causes the kernel to check the ACPI hardware + signature during resume from hibernation, and gracefully + refuse to resume if it has changed. This complies with + the ACPI specification but not with reality, since + Windows does not do this and many laptops do change it + on docking. So the default behaviour is to allow resume + and simply warn when the signature changes, unless the + s4_hwsig option is enabled. + s4_nohwsig prevents ACPI hardware signature from being + used (or even warned about) during resume. + old_ordering causes the ACPI 1.0 ordering of the _PTS + control method, with respect to putting devices into + low power states, to be enforced (the ACPI 2.0 ordering + of _PTS is used by default). + nonvs prevents the kernel from saving/restoring the + ACPI NVS memory during suspend/hibernation and resume. + sci_force_enable causes the kernel to set SCI_EN directly + on resume from S1/S3 (which is against the ACPI spec, + but some broken systems don't work without it). + nobl causes the internal blacklist of systems known to + behave incorrectly in some ways with respect to system + suspend and resume to be ignored (use wisely). + + acpi_use_timer_override [HW,ACPI] + Use timer override. For some broken Nvidia NF5 boards + that require a timer override, but don't have HPET + + add_efi_memmap [EFI; X86] Include EFI memory map in + kernel's map of available physical RAM. + + agp= [AGP] + { off | try_unsupported } + off: disable AGP support + try_unsupported: try to drive unsupported chipsets + (may crash computer or cause data corruption) + + ALSA [HW,ALSA] + See Documentation/sound/alsa-configuration.rst + + alignment= [KNL,ARM] + Allow the default userspace alignment fault handler + behaviour to be specified. Bit 0 enables warnings, + bit 1 enables fixups, and bit 2 sends a segfault. + + align_va_addr= [X86-64] + Align virtual addresses by clearing slice [14:12] when + allocating a VMA at process creation time. This option + gives you up to 3% performance improvement on AMD F15h + machines (where it is enabled by default) for a + CPU-intensive style benchmark, and it can vary highly in + a microbenchmark depending on workload and compiler. + + 32: only for 32-bit processes + 64: only for 64-bit processes + on: enable for both 32- and 64-bit processes + off: disable for both 32- and 64-bit processes + + alloc_snapshot [FTRACE] + Allocate the ftrace snapshot buffer on boot up when the + main buffer is allocated. This is handy if debugging + and you need to use tracing_snapshot() on boot up, and + do not want to use tracing_snapshot_alloc() as it needs + to be done where GFP_KERNEL allocations are allowed. + + allow_mismatched_32bit_el0 [ARM64] + Allow execve() of 32-bit applications and setting of the + PER_LINUX32 personality on systems where only a strict + subset of the CPUs support 32-bit EL0. When this + parameter is present, the set of CPUs supporting 32-bit + EL0 is indicated by /sys/devices/system/cpu/aarch32_el0 + and hot-unplug operations may be restricted. + + See Documentation/arm64/asymmetric-32bit.rst for more + information. + + amd_iommu= [HW,X86-64] + Pass parameters to the AMD IOMMU driver in the system. + Possible values are: + fullflush - Deprecated, equivalent to iommu.strict=1 + off - do not initialize any AMD IOMMU found in + the system + force_isolation - Force device isolation for all + devices. The IOMMU driver is not + allowed anymore to lift isolation + requirements as needed. This option + does not override iommu=pt + force_enable - Force enable the IOMMU on platforms known + to be buggy with IOMMU enabled. Use this + option with care. + pgtbl_v1 - Use v1 page table for DMA-API (Default). + pgtbl_v2 - Use v2 page table for DMA-API. + irtcachedis - Disable Interrupt Remapping Table (IRT) caching. + + amd_iommu_dump= [HW,X86-64] + Enable AMD IOMMU driver option to dump the ACPI table + for AMD IOMMU. With this option enabled, AMD IOMMU + driver will print ACPI tables for AMD IOMMU during + IOMMU initialization. + + amd_iommu_intr= [HW,X86-64] + Specifies one of the following AMD IOMMU interrupt + remapping modes: + legacy - Use legacy interrupt remapping mode. + vapic - Use virtual APIC mode, which allows IOMMU + to inject interrupts directly into guest. + This mode requires kvm-amd.avic=1. + (Default when IOMMU HW support is present.) + + amijoy.map= [HW,JOY] Amiga joystick support + Map of devices attached to JOY0DAT and JOY1DAT + Format: <a>,<b> + See also Documentation/input/joydev/joystick.rst + + analog.map= [HW,JOY] Analog joystick and gamepad support + Specifies type or capabilities of an analog joystick + connected to one of 16 gameports + Format: <type1>,<type2>,..<type16> + + apc= [HW,SPARC] + Power management functions (SPARCstation-4/5 + deriv.) + Format: noidle + Disable APC CPU standby support. SPARCstation-Fox does + not play well with APC CPU idle - disable it if you have + APC and your system crashes randomly. + + apic= [APIC,X86] Advanced Programmable Interrupt Controller + Change the output verbosity while booting + Format: { quiet (default) | verbose | debug } + Change the amount of debugging information output + when initialising the APIC and IO-APIC components. + For X86-32, this can also be used to specify an APIC + driver name. + Format: apic=driver_name + Examples: apic=bigsmp + + apic_extnmi= [APIC,X86] External NMI delivery setting + Format: { bsp (default) | all | none } + bsp: External NMI is delivered only to CPU 0 + all: External NMIs are broadcast to all CPUs as a + backup of CPU 0 + none: External NMI is masked for all CPUs. This is + useful so that a dump capture kernel won't be + shot down by NMI + + autoconf= [IPV6] + See Documentation/networking/ipv6.rst. + + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller + Limit apic dumping. The parameter defines the maximal + number of local apics being dumped. Also it is possible + to set it to "all" by meaning -- no limit here. + Format: { 1 (default) | 2 | ... | all }. + The parameter valid if only apic=debug or + apic=verbose is specified. + Example: apic=debug show_lapic=all + + apm= [APM] Advanced Power Management + See header of arch/x86/kernel/apm_32.c. + + arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards + Format: <io>,<irq>,<nodeID> + + arm64.nobti [ARM64] Unconditionally disable Branch Target + Identification support + + arm64.nopauth [ARM64] Unconditionally disable Pointer Authentication + support + + arm64.nomte [ARM64] Unconditionally disable Memory Tagging Extension + support + + arm64.nosve [ARM64] Unconditionally disable Scalable Vector + Extension support + + arm64.nosme [ARM64] Unconditionally disable Scalable Matrix + Extension support + + ataflop= [HW,M68k] + + atarimouse= [HW,MOUSE] Atari Mouse + + atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess, + EzKey and similar keyboards + + atkbd.reset= [HW] Reset keyboard during initialization + + atkbd.set= [HW] Select keyboard code set + Format: <int> (2 = AT (default), 3 = PS/2) + + atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar + keyboards + + atkbd.softraw= [HW] Choose between synthetic and real raw mode + Format: <bool> (0 = real, 1 = synthetic (default)) + + atkbd.softrepeat= [HW] + Use software keyboard repeat + + audit= [KNL] Enable the audit sub-system + Format: { "0" | "1" | "off" | "on" } + 0 | off - kernel audit is disabled and can not be + enabled until the next reboot + unset - kernel audit is initialized but disabled and + will be fully enabled by the userspace auditd. + 1 | on - kernel audit is initialized and partially + enabled, storing at most audit_backlog_limit + messages in RAM until it is fully enabled by the + userspace auditd. + Default: unset + + audit_backlog_limit= [KNL] Set the audit queue size limit. + Format: <int> (must be >=0) + Default: 64 + + bau= [X86_UV] Enable the BAU on SGI UV. The default + behavior is to disable the BAU (i.e. bau=0). + Format: { "0" | "1" } + 0 - Disable the BAU. + 1 - Enable the BAU. + unset - Disable the BAU. + + baycom_epp= [HW,AX25] + Format: <io>,<mode> + + baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem + Format: <io>,<mode> + See header of drivers/net/hamradio/baycom_par.c. + + baycom_ser_fdx= [HW,AX25] + BayCom Serial Port AX.25 Modem (Full Duplex Mode) + Format: <io>,<irq>,<mode>[,<baud>] + See header of drivers/net/hamradio/baycom_ser_fdx.c. + + baycom_ser_hdx= [HW,AX25] + BayCom Serial Port AX.25 Modem (Half Duplex Mode) + Format: <io>,<irq>,<mode> + See header of drivers/net/hamradio/baycom_ser_hdx.c. + + bert_disable [ACPI] + Disable BERT OS support on buggy BIOSes. + + bgrt_disable [ACPI][X86] + Disable BGRT to avoid flickering OEM logo. + + blkdevparts= Manual partition parsing of block device(s) for + embedded devices based on command line input. + See Documentation/block/cmdline-partition.rst + + boot_delay= Milliseconds to delay each printk during boot. + Values larger than 10 seconds (10000) are changed to + no delay (0). + Format: integer + + bootconfig [KNL] + Extended command line options can be added to an initrd + and this will cause the kernel to look for it. + + See Documentation/admin-guide/bootconfig.rst + + bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards) + bttv.radio= Most important insmod options are available as + kernel args too. + bttv.pll= See Documentation/admin-guide/media/bttv.rst + bttv.tuner= + + bulk_remove=off [PPC] This parameter disables the use of the pSeries + firmware feature for flushing multiple hpte entries + at a time. + + c101= [NET] Moxa C101 synchronous serial card + + cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection. + Sometimes CPU hardware bugs make them report the cache + size incorrectly. The kernel will attempt work arounds + to fix known problems, but for some CPUs it is not + possible to determine what the correct size should be. + This option provides an override for these situations. + + carrier_timeout= + [NET] Specifies amount of time (in seconds) that + the kernel should wait for a network carrier. By default + it waits 120 seconds. + + ca_keys= [KEYS] This parameter identifies a specific key(s) on + the system trusted keyring to be used for certificate + trust validation. + format: { id:<keyid> | builtin } + + cca= [MIPS] Override the kernel pages' cache coherency + algorithm. Accepted values range from 0 to 7 + inclusive. See arch/mips/include/asm/pgtable-bits.h + for platform specific values (SB1, Loongson3 and + others). + + ccw_timeout_log [S390] + See Documentation/s390/common_io.rst for details. + + cgroup_disable= [KNL] Disable a particular controller or optional feature + Format: {name of the controller(s) or feature(s) to disable} + The effects of cgroup_disable=foo are: + - foo isn't auto-mounted if you mount all cgroups in + a single hierarchy + - foo isn't visible as an individually mountable + subsystem + - if foo is an optional feature then the feature is + disabled and corresponding cgroup files are not + created + {Currently only "memory" controller deal with this and + cut the overhead, others just disable the usage. So + only cgroup_disable=memory is actually worthy} + Specifying "pressure" disables per-cgroup pressure + stall information accounting feature + + cgroup_no_v1= [KNL] Disable cgroup controllers and named hierarchies in v1 + Format: { { controller | "all" | "named" } + [,{ controller | "all" | "named" }...] } + Like cgroup_disable, but only applies to cgroup v1; + the blacklisted controllers remain available in cgroup2. + "all" blacklists all controllers and "named" disables + named mounts. Specifying both "all" and "named" disables + all v1 hierarchies. + + cgroup.memory= [KNL] Pass options to the cgroup memory controller. + Format: <string> + nosocket -- Disable socket memory accounting. + nokmem -- Disable kernel memory accounting. + + checkreqprot= [SELINUX] Set initial checkreqprot flag value. + Format: { "0" | "1" } + See security/selinux/Kconfig help text. + 0 -- check protection applied by kernel (includes + any implied execute protection). + 1 -- check protection requested by application. + Default value is set via a kernel config option. + Value can be changed at runtime via + /sys/fs/selinux/checkreqprot. + Setting checkreqprot to 1 is deprecated. + + cio_ignore= [S390] + See Documentation/s390/common_io.rst for details. + + clearcpuid=X[,X...] [X86] + Disable CPUID feature X for the kernel. See + arch/x86/include/asm/cpufeatures.h for the valid bit + numbers X. Note the Linux-specific bits are not necessarily + stable over kernel options, but the vendor-specific + ones should be. + X can also be a string as appearing in the flags: line + in /proc/cpuinfo which does not have the above + instability issue. However, not all features have names + in /proc/cpuinfo. + Note that using this option will taint your kernel. + Also note that user programs calling CPUID directly + or using the feature without checking anything + will still see it. This just prevents it from + being used by the kernel or shown in /proc/cpuinfo. + Also note the kernel might malfunction if you disable + some critical bits. + + clk_ignore_unused + [CLK] + Prevents the clock framework from automatically gating + clocks that have not been explicitly enabled by a Linux + device driver but are enabled in hardware at reset or + by the bootloader/firmware. Note that this does not + force such clocks to be always-on nor does it reserve + those clocks in any way. This parameter is useful for + debug and development, but should not be needed on a + platform with proper driver support. For more + information, see Documentation/driver-api/clk.rst. + + clock= [BUGS=X86-32, HW] gettimeofday clocksource override. + [Deprecated] + Forces specified clocksource (if available) to be used + when calculating gettimeofday(). If specified + clocksource is not available, it defaults to PIT. + Format: { pit | tsc | cyclone | pmtmr } + + clocksource= Override the default clocksource + Format: <string> + Override the default clocksource and use the clocksource + with the name specified. + Some clocksource names to choose from, depending on + the platform: + [all] jiffies (this is the base, fallback clocksource) + [ACPI] acpi_pm + [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2, + pxa_timer,timer3,32k_counter,timer0_1 + [X86-32] pit,hpet,tsc; + scx200_hrt on Geode; cyclone on IBM x440 + [MIPS] MIPS + [PARISC] cr16 + [S390] tod + [SH] SuperH + [SPARC64] tick + [X86-64] hpet,tsc + + clocksource.arm_arch_timer.evtstrm= + [ARM,ARM64] + Format: <bool> + Enable/disable the eventstream feature of the ARM + architected timer so that code using WFE-based polling + loops can be debugged more effectively on production + systems. + + clocksource.max_cswd_read_retries= [KNL] + Number of clocksource_watchdog() retries due to + external delays before the clock will be marked + unstable. Defaults to two retries, that is, + three attempts to read the clock under test. + + clocksource.verify_n_cpus= [KNL] + Limit the number of CPUs checked for clocksources + marked with CLOCK_SOURCE_VERIFY_PERCPU that + are marked unstable due to excessive skew. + A negative value says to check all CPUs, while + zero says not to check any. Values larger than + nr_cpu_ids are silently truncated to nr_cpu_ids. + The actual CPUs are chosen randomly, with + no replacement if the same CPU is chosen twice. + + clocksource-wdtest.holdoff= [KNL] + Set the time in seconds that the clocksource + watchdog test waits before commencing its tests. + Defaults to zero when built as a module and to + 10 seconds when built into the kernel. + + cma=nn[MG]@[start[MG][-end[MG]]] + [KNL,CMA] + Sets the size of kernel global memory area for + contiguous memory allocations and optionally the + placement constraint by the physical address range of + memory allocations. A value of 0 disables CMA + altogether. For more information, see + kernel/dma/contiguous.c + + cma_pernuma=nn[MG] + [ARM64,KNL,CMA] + Sets the size of kernel per-numa memory area for + contiguous memory allocations. A value of 0 disables + per-numa CMA altogether. And If this option is not + specificed, the default value is 0. + With per-numa CMA enabled, DMA users on node nid will + first try to allocate buffer from the pernuma area + which is located in node nid, if the allocation fails, + they will fallback to the global default memory area. + + cmo_free_hint= [PPC] Format: { yes | no } + Specify whether pages are marked as being inactive + when they are freed. This is used in CMO environments + to determine OS memory pressure for page stealing by + a hypervisor. + Default: yes + + coherent_pool=nn[KMG] [ARM,KNL] + Sets the size of memory pool for coherent, atomic dma + allocations, by default set to 256K. + + com20020= [HW,NET] ARCnet - COM20020 chipset + Format: + <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]] + + com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers) + Format: <io>[,<irq>] + + com90xx= [HW,NET] + ARCnet - COM90xx chipset (memory-mapped buffers) + Format: <io>[,<irq>[,<memstart>]] + + condev= [HW,S390] console device + conmode= + + console= [KNL] Output console device and options. + + tty<n> Use the virtual console device <n>. + + ttyS<n>[,options] + ttyUSB0[,options] + Use the specified serial port. The options are of + the form "bbbbpnf", where "bbbb" is the baud rate, + "p" is parity ("n", "o", or "e"), "n" is number of + bits, and "f" is flow control ("r" for RTS or + omit it). Default is "9600n8". + + See Documentation/admin-guide/serial-console.rst for more + information. See + Documentation/networking/netconsole.rst for an + alternative. + + uart[8250],io,<addr>[,options] + uart[8250],mmio,<addr>[,options] + uart[8250],mmio16,<addr>[,options] + uart[8250],mmio32,<addr>[,options] + uart[8250],0x<addr>[,options] + Start an early, polled-mode console on the 8250/16550 + UART at the specified I/O port or MMIO address, + switching to the matching ttyS device later. + MMIO inter-register address stride is either 8-bit + (mmio), 16-bit (mmio16), or 32-bit (mmio32). + If none of [io|mmio|mmio16|mmio32], <addr> is assumed + to be equivalent to 'mmio'. 'options' are specified in + the same format described for ttyS above; if unspecified, + the h/w is not re-initialized. + + hvc<n> Use the hypervisor console device <n>. This is for + both Xen and PowerPC hypervisors. + + { null | "" } + Use to disable console output, i.e., to have kernel + console messages discarded. + This must be the only console= parameter used on the + kernel command line. + + If the device connected to the port is not a TTY but a braille + device, prepend "brl," before the device type, for instance + console=brl,ttyS0 + For now, only VisioBraille is supported. + + console_msg_format= + [KNL] Change console messages format + default + By default we print messages on consoles in + "[time stamp] text\n" format (time stamp may not be + printed, depending on CONFIG_PRINTK_TIME or + `printk_time' param). + syslog + Switch to syslog format: "<%u>[time stamp] text\n" + IOW, each message will have a facility and loglevel + prefix. The format is similar to one used by syslog() + syscall, or to executing "dmesg -S --raw" or to reading + from /proc/kmsg. + + consoleblank= [KNL] The console blank (screen saver) timeout in + seconds. A value of 0 disables the blank timer. + Defaults to 0. + + coredump_filter= + [KNL] Change the default value for + /proc/<pid>/coredump_filter. + See also Documentation/filesystems/proc.rst. + + coresight_cpu_debug.enable + [ARM,ARM64] + Format: <bool> + Enable/disable the CPU sampling based debugging. + 0: default value, disable debugging + 1: enable debugging at boot time + + cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver + Format: + <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>] + + cpu0_hotplug [X86] Turn on CPU0 hotplug feature when + CONFIG_BOOTPARAM_HOTPLUG_CPU0 is off. + Some features depend on CPU0. Known dependencies are: + 1. Resume from suspend/hibernate depends on CPU0. + Suspend/hibernate will fail if CPU0 is offline and you + need to online CPU0 before suspend/hibernate. + 2. PIC interrupts also depend on CPU0. CPU0 can't be + removed if a PIC interrupt is detected. + It's said poweroff/reboot may depend on CPU0 on some + machines although I haven't seen such issues so far + after CPU0 is offline on a few tested machines. + If the dependencies are under your control, you can + turn on cpu0_hotplug. + + cpuidle.off=1 [CPU_IDLE] + disable the cpuidle sub-system + + cpuidle.governor= + [CPU_IDLE] Name of the cpuidle governor to use. + + cpufreq.off=1 [CPU_FREQ] + disable the cpufreq sub-system + + cpufreq.default_governor= + [CPU_FREQ] Name of the default cpufreq governor or + policy to use. This governor must be registered in the + kernel before the cpufreq driver probes. + + cpu_init_udelay=N + [X86] Delay for N microsec between assert and de-assert + of APIC INIT to start processors. This delay occurs + on every CPU online, such as boot, and resume from suspend. + Default: 10000 + + crash_kexec_post_notifiers + Run kdump after running panic-notifiers and dumping + kmsg. This only for the users who doubt kdump always + succeeds in any situation. + Note that this also increases risks of kdump failure, + because some panic notifiers can make the crashed + kernel more unstable. + + crashkernel=size[KMG][@offset[KMG]] + [KNL] Using kexec, Linux can switch to a 'crash kernel' + upon panic. This parameter reserves the physical + memory region [offset, offset + size] for that kernel + image. If '@offset' is omitted, then a suitable offset + is selected automatically. + [KNL, X86-64] Select a region under 4G first, and + fall back to reserve region above 4G when '@offset' + hasn't been specified. + See Documentation/admin-guide/kdump/kdump.rst for further details. + + crashkernel=range1:size1[,range2:size2,...][@offset] + [KNL] Same as above, but depends on the memory + in the running system. The syntax of range is + start-[end] where start and end are both + a memory unit (amount[KMG]). See also + Documentation/admin-guide/kdump/kdump.rst for an example. + + crashkernel=size[KMG],high + [KNL, X86-64, ARM64] range could be above 4G. Allow kernel + to allocate physical memory region from top, so could + be above 4G if system have more than 4G ram installed. + Otherwise memory region will be allocated below 4G, if + available. + It will be ignored if crashkernel=X is specified. + crashkernel=size[KMG],low + [KNL, X86-64] range under 4G. When crashkernel=X,high + is passed, kernel could allocate physical memory region + above 4G, that cause second kernel crash on system + that require some amount of low memory, e.g. swiotlb + requires at least 64M+32K low memory, also enough extra + low memory is needed to make sure DMA buffers for 32-bit + devices won't run out. Kernel would try to allocate + at least 256M below 4G automatically. + This one lets the user specify own low range under 4G + for second kernel instead. + 0: to disable low allocation. + It will be ignored when crashkernel=X,high is not used + or memory reserved is below 4G. + + [KNL, ARM64] range in low memory. + This one lets the user specify a low range in the + DMA zone for the crash dump kernel. + It will be ignored when crashkernel=X,high is not used + or memory reserved is located in the DMA zones. + + cryptomgr.notests + [KNL] Disable crypto self-tests + + cs89x0_dma= [HW,NET] + Format: <dma> + + cs89x0_media= [HW,NET] + Format: { rj45 | aui | bnc } + + csdlock_debug= [KNL] Enable debug add-ons of cross-CPU function call + handling. When switched on, additional debug data is + printed to the console in case a hanging CPU is + detected, and that CPU is pinged again in order to try + to resolve the hang situation. + 0: disable csdlock debugging (default) + 1: enable basic csdlock debugging (minor impact) + ext: enable extended csdlock debugging (more impact, + but more data) + + dasd= [HW,NET] + See header of drivers/s390/block/dasd_devmap.c. + + db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port + (one device per port) + Format: <port#>,<type> + See also Documentation/input/devices/joystick-parport.rst + + debug [KNL] Enable kernel debugging (events log level). + + debug_boot_weak_hash + [KNL] Enable printing [hashed] pointers early in the + boot sequence. If enabled, we use a weak hash instead + of siphash to hash pointers. Use this option if you are + seeing instances of '(___ptrval___)') and need to see a + value (hashed pointer) instead. Cryptographically + insecure, please do not use on production kernels. + + debug_locks_verbose= + [KNL] verbose locking self-tests + Format: <int> + Print debugging info while doing the locking API + self-tests. + Bitmask for the various LOCKTYPE_ tests. Defaults to 0 + (no extra messages), setting it to -1 (all bits set) + will print _a_lot_ more information - normally only + useful to lockdep developers. + + debug_objects [KNL] Enable object debugging + + no_debug_objects + [KNL] Disable object debugging + + debug_guardpage_minorder= + [KNL] When CONFIG_DEBUG_PAGEALLOC is set, this + parameter allows control of the order of pages that will + be intentionally kept free (and hence protected) by the + buddy allocator. Bigger value increase the probability + of catching random memory corruption, but reduce the + amount of memory for normal system use. The maximum + possible value is MAX_ORDER/2. Setting this parameter + to 1 or 2 should be enough to identify most random + memory corruption problems caused by bugs in kernel or + driver code when a CPU writes to (or reads from) a + random memory location. Note that there exists a class + of memory corruptions problems caused by buggy H/W or + F/W or by drivers badly programing DMA (basically when + memory is written at bus level and the CPU MMU is + bypassed) which are not detectable by + CONFIG_DEBUG_PAGEALLOC, hence this option will not help + tracking down these problems. + + debug_pagealloc= + [KNL] When CONFIG_DEBUG_PAGEALLOC is set, this parameter + enables the feature at boot time. By default, it is + disabled and the system will work mostly the same as a + kernel built without CONFIG_DEBUG_PAGEALLOC. + Note: to get most of debug_pagealloc error reports, it's + useful to also enable the page_owner functionality. + on: enable the feature + + debugfs= [KNL] This parameter enables what is exposed to userspace + and debugfs internal clients. + Format: { on, no-mount, off } + on: All functions are enabled. + no-mount: + Filesystem is not registered but kernel clients can + access APIs and a crashkernel can be used to read + its content. There is nothing to mount. + off: Filesystem is not registered and clients + get a -EPERM as result when trying to register files + or directories within debugfs. + This is equivalent of the runtime functionality if + debugfs was not enabled in the kernel at all. + Default value is set in build-time with a kernel configuration. + + debugpat [X86] Enable PAT debugging + + default_hugepagesz= + [HW] The size of the default HugeTLB page. This is + the size represented by the legacy /proc/ hugepages + APIs. In addition, this is the default hugetlb size + used for shmget(), mmap() and mounting hugetlbfs + filesystems. If not specified, defaults to the + architecture's default huge page size. Huge page + sizes are architecture dependent. See also + Documentation/admin-guide/mm/hugetlbpage.rst. + Format: size[KMG] + + deferred_probe_timeout= + [KNL] Debugging option to set a timeout in seconds for + deferred probe to give up waiting on dependencies to + probe. Only specific dependencies (subsystems or + drivers) that have opted in will be ignored. A timeout + of 0 will timeout at the end of initcalls. If the time + out hasn't expired, it'll be restarted by each + successful driver registration. This option will also + dump out devices still on the deferred probe list after + retrying. + + delayacct [KNL] Enable per-task delay accounting + + dell_smm_hwmon.ignore_dmi= + [HW] Continue probing hardware even if DMI data + indicates that the driver is running on unsupported + hardware. + + dell_smm_hwmon.force= + [HW] Activate driver even if SMM BIOS signature does + not match list of supported models and enable otherwise + blacklisted features. + + dell_smm_hwmon.power_status= + [HW] Report power status in /proc/i8k + (disabled by default). + + dell_smm_hwmon.restricted= + [HW] Allow controlling fans only if SYS_ADMIN + capability is set. + + dell_smm_hwmon.fan_mult= + [HW] Factor to multiply fan speed with. + + dell_smm_hwmon.fan_max= + [HW] Maximum configurable fan speed. + + dfltcc= [HW,S390] + Format: { on | off | def_only | inf_only | always } + on: s390 zlib hardware support for compression on + level 1 and decompression (default) + off: No s390 zlib hardware support + def_only: s390 zlib hardware support for deflate + only (compression on level 1) + inf_only: s390 zlib hardware support for inflate + only (decompression) + always: Same as 'on' but ignores the selected compression + level always using hardware support (used for debugging) + + dhash_entries= [KNL] + Set number of hash buckets for dentry cache. + + disable_1tb_segments [PPC] + Disables the use of 1TB hash page table segments. This + causes the kernel to fall back to 256MB segments which + can be useful when debugging issues that require an SLB + miss to occur. + + stress_slb [PPC] + Limits the number of kernel SLB entries, and flushes + them frequently to increase the rate of SLB faults + on kernel addresses. + + disable= [IPV6] + See Documentation/networking/ipv6.rst. + + disable_radix [PPC] + Disable RADIX MMU mode on POWER9 + + radix_hcall_invalidate=on [PPC/PSERIES] + Disable RADIX GTSE feature and use hcall for TLB + invalidate. + + disable_tlbie [PPC] + Disable TLBIE instruction. Currently does not work + with KVM, with HASH MMU, or with coherent accelerators. + + disable_cpu_apicid= [X86,APIC,SMP] + Format: <int> + The number of initial APIC ID for the + corresponding CPU to be disabled at boot, + mostly used for the kdump 2nd kernel to + disable BSP to wake up multiple CPUs without + causing system reset or hang due to sending + INIT from AP to BSP. + + disable_ddw [PPC/PSERIES] + Disable Dynamic DMA Window support. Use this + to workaround buggy firmware. + + disable_ipv6= [IPV6] + See Documentation/networking/ipv6.rst. + + disable_mtrr_cleanup [X86] + The kernel tries to adjust MTRR layout from continuous + to discrete, to make X server driver able to add WB + entry later. This parameter disables that. + + disable_mtrr_trim [X86, Intel and AMD only] + By default the kernel will trim any uncacheable + memory out of your available memory pool based on + MTRR settings. This parameter disables that behavior, + possibly causing your machine to run very slowly. + + disable_timer_pin_1 [X86] + Disable PIN 1 of APIC timer + Can be useful to work around chipset bugs. + + dis_ucode_ldr [X86] Disable the microcode loader. + + dma_debug=off If the kernel is compiled with DMA_API_DEBUG support, + this option disables the debugging code at boot. + + dma_debug_entries=<number> + This option allows to tune the number of preallocated + entries for DMA-API debugging code. One entry is + required per DMA-API allocation. Use this if the + DMA-API debugging code disables itself because the + architectural default is too low. + + dma_debug_driver=<driver_name> + With this option the DMA-API debugging driver + filter feature can be enabled at boot time. Just + pass the driver to filter for as the parameter. + The filter can be disabled or changed to another + driver later using sysfs. + + driver_async_probe= [KNL] + List of driver names to be probed asynchronously. * + matches with all driver names. If * is specified, the + rest of the listed driver names are those that will NOT + match the *. + Format: <driver_name1>,<driver_name2>... + + drm.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] + Broken monitors, graphic adapters, KVMs and EDIDless + panels may send no or incorrect EDID data sets. + This parameter allows to specify an EDID data sets + in the /lib/firmware directory that are used instead. + Generic built-in EDID data sets are used, if one of + edid/1024x768.bin, edid/1280x1024.bin, + edid/1680x1050.bin, or edid/1920x1080.bin is given + and no file with the same name exists. Details and + instructions how to build your own EDID data are + available in Documentation/admin-guide/edid.rst. An EDID + data set will only be used for a particular connector, + if its name and a colon are prepended to the EDID + name. Each connector may use a unique EDID data + set by separating the files with a comma. An EDID + data set with no connector name will be used for + any connectors not explicitly specified. + + dscc4.setup= [NET] + + dt_cpu_ftrs= [PPC] + Format: {"off" | "known"} + Control how the dt_cpu_ftrs device-tree binding is + used for CPU feature discovery and setup (if it + exists). + off: Do not use it, fall back to legacy cpu table. + known: Do not pass through unknown features to guests + or userspace, only those that the kernel is aware of. + + dump_apple_properties [X86] + Dump name and content of EFI device properties on + x86 Macs. Useful for driver authors to determine + what data is available or for reverse-engineering. + + dyndbg[="val"] [KNL,DYNAMIC_DEBUG] + <module>.dyndbg[="val"] + Enable debug messages at boot time. See + Documentation/admin-guide/dynamic-debug-howto.rst + for details. + + nopku [X86] Disable Memory Protection Keys CPU feature found + in some Intel CPUs. + + <module>.async_probe[=<bool>] [KNL] + If no <bool> value is specified or if the value + specified is not a valid <bool>, enable asynchronous + probe on this module. Otherwise, enable/disable + asynchronous probe on this module as indicated by the + <bool> value. See also: module.async_probe + + early_ioremap_debug [KNL] + Enable debug messages in early_ioremap support. This + is useful for tracking down temporary early mappings + which are not unmapped. + + earlycon= [KNL] Output early console device and options. + + When used with no options, the early console is + determined by stdout-path property in device tree's + chosen node or the ACPI SPCR table if supported by + the platform. + + cdns,<addr>[,options] + Start an early, polled-mode console on a Cadence + (xuartps) serial port at the specified address. Only + supported option is baud rate. If baud rate is not + specified, the serial port must already be setup and + configured. + + uart[8250],io,<addr>[,options] + uart[8250],mmio,<addr>[,options] + uart[8250],mmio32,<addr>[,options] + uart[8250],mmio32be,<addr>[,options] + uart[8250],0x<addr>[,options] + Start an early, polled-mode console on the 8250/16550 + UART at the specified I/O port or MMIO address. + MMIO inter-register address stride is either 8-bit + (mmio) or 32-bit (mmio32 or mmio32be). + If none of [io|mmio|mmio32|mmio32be], <addr> is assumed + to be equivalent to 'mmio'. 'options' are specified + in the same format described for "console=ttyS<n>"; if + unspecified, the h/w is not initialized. + + pl011,<addr> + pl011,mmio32,<addr> + Start an early, polled-mode console on a pl011 serial + port at the specified address. The pl011 serial port + must already be setup and configured. Options are not + yet supported. If 'mmio32' is specified, then only + the driver will use only 32-bit accessors to read/write + the device registers. + + liteuart,<addr> + Start an early console on a litex serial port at the + specified address. The serial port must already be + setup and configured. Options are not yet supported. + + meson,<addr> + Start an early, polled-mode console on a meson serial + port at the specified address. The serial port must + already be setup and configured. Options are not yet + supported. + + msm_serial,<addr> + Start an early, polled-mode console on an msm serial + port at the specified address. The serial port + must already be setup and configured. Options are not + yet supported. + + msm_serial_dm,<addr> + Start an early, polled-mode console on an msm serial + dm port at the specified address. The serial port + must already be setup and configured. Options are not + yet supported. + + owl,<addr> + Start an early, polled-mode console on a serial port + of an Actions Semi SoC, such as S500 or S900, at the + specified address. The serial port must already be + setup and configured. Options are not yet supported. + + rda,<addr> + Start an early, polled-mode console on a serial port + of an RDA Micro SoC, such as RDA8810PL, at the + specified address. The serial port must already be + setup and configured. Options are not yet supported. + + sbi + Use RISC-V SBI (Supervisor Binary Interface) for early + console. + + smh Use ARM semihosting calls for early console. + + s3c2410,<addr> + s3c2412,<addr> + s3c2440,<addr> + s3c6400,<addr> + s5pv210,<addr> + exynos4210,<addr> + Use early console provided by serial driver available + on Samsung SoCs, requires selecting proper type and + a correct base address of the selected UART port. The + serial port must already be setup and configured. + Options are not yet supported. + + lantiq,<addr> + Start an early, polled-mode console on a lantiq serial + (lqasc) port at the specified address. The serial port + must already be setup and configured. Options are not + yet supported. + + lpuart,<addr> + lpuart32,<addr> + Use early console provided by Freescale LP UART driver + found on Freescale Vybrid and QorIQ LS1021A processors. + A valid base address must be provided, and the serial + port must already be setup and configured. + + ec_imx21,<addr> + ec_imx6q,<addr> + Start an early, polled-mode, output-only console on the + Freescale i.MX UART at the specified address. The UART + must already be setup and configured. + + ar3700_uart,<addr> + Start an early, polled-mode console on the + Armada 3700 serial port at the specified + address. The serial port must already be setup + and configured. Options are not yet supported. + + qcom_geni,<addr> + Start an early, polled-mode console on a Qualcomm + Generic Interface (GENI) based serial port at the + specified address. The serial port must already be + setup and configured. Options are not yet supported. + + efifb,[options] + Start an early, unaccelerated console on the EFI + memory mapped framebuffer (if available). On cache + coherent non-x86 systems that use system memory for + the framebuffer, pass the 'ram' option so that it is + mapped with the correct attributes. + + linflex,<addr> + Use early console provided by Freescale LINFlexD UART + serial driver for NXP S32V234 SoCs. A valid base + address must be provided, and the serial port must + already be setup and configured. + + earlyprintk= [X86,SH,ARM,M68k,S390] + earlyprintk=vga + earlyprintk=sclp + earlyprintk=xen + earlyprintk=serial[,ttySn[,baudrate]] + earlyprintk=serial[,0x...[,baudrate]] + earlyprintk=ttySn[,baudrate] + earlyprintk=dbgp[debugController#] + earlyprintk=pciserial[,force],bus:device.function[,baudrate] + earlyprintk=xdbc[xhciController#] + + earlyprintk is useful when the kernel crashes before + the normal console is initialized. It is not enabled by + default because it has some cosmetic problems. + + Append ",keep" to not disable it when the real console + takes over. + + Only one of vga, serial, or usb debug port can + be used at a time. + + Currently only ttyS0 and ttyS1 may be specified by + name. Other I/O ports may be explicitly specified + on some architectures (x86 and arm at least) by + replacing ttySn with an I/O port address, like this: + earlyprintk=serial,0x1008,115200 + You can find the port for a given device in + /proc/tty/driver/serial: + 2: uart:ST16650V2 port:00001008 irq:18 ... + + Interaction with the standard serial driver is not + very good. + + The VGA output is eventually overwritten by + the real console. + + The xen option can only be used in Xen domains. + + The sclp output can only be used on s390. + + The optional "force" to "pciserial" enables use of a + PCI device even when its classcode is not of the + UART class. + + edac_report= [HW,EDAC] Control how to report EDAC event + Format: {"on" | "off" | "force"} + on: enable EDAC to report H/W event. May be overridden + by other higher priority error reporting module. + off: disable H/W event reporting through EDAC. + force: enforce the use of EDAC to report H/W event. + default: on. + + edd= [EDD] + Format: {"off" | "on" | "skip[mbr]"} + + efi= [EFI] + Format: { "debug", "disable_early_pci_dma", + "nochunk", "noruntime", "nosoftreserve", + "novamap", "no_disable_early_pci_dma" } + debug: enable misc debug output. + disable_early_pci_dma: disable the busmaster bit on all + PCI bridges while in the EFI boot stub. + nochunk: disable reading files in "chunks" in the EFI + boot stub, as chunking can cause problems with some + firmware implementations. + noruntime : disable EFI runtime services support + nosoftreserve: The EFI_MEMORY_SP (Specific Purpose) + attribute may cause the kernel to reserve the + memory range for a memory mapping driver to + claim. Specify efi=nosoftreserve to disable this + reservation and treat the memory by its base type + (i.e. EFI_CONVENTIONAL_MEMORY / "System RAM"). + novamap: do not call SetVirtualAddressMap(). + no_disable_early_pci_dma: Leave the busmaster bit set + on all PCI bridges while in the EFI boot stub + + efi_no_storage_paranoia [EFI; X86] + Using this parameter you can use more than 50% of + your efi variable storage. Use this parameter only if + you are really sure that your UEFI does sane gc and + fulfills the spec otherwise your board may brick. + + efi_fake_mem= nn[KMG]@ss[KMG]:aa[,nn[KMG]@ss[KMG]:aa,..] [EFI; X86] + Add arbitrary attribute to specific memory range by + updating original EFI memory map. + Region of memory which aa attribute is added to is + from ss to ss+nn. + + If efi_fake_mem=2G@4G:0x10000,2G@0x10a0000000:0x10000 + is specified, EFI_MEMORY_MORE_RELIABLE(0x10000) + attribute is added to range 0x100000000-0x180000000 and + 0x10a0000000-0x1120000000. + + If efi_fake_mem=8G@9G:0x40000 is specified, the + EFI_MEMORY_SP(0x40000) attribute is added to + range 0x240000000-0x43fffffff. + + Using this parameter you can do debugging of EFI memmap + related features. For example, you can do debugging of + Address Range Mirroring feature even if your box + doesn't support it, or mark specific memory as + "soft reserved". + + efivar_ssdt= [EFI; X86] Name of an EFI variable that contains an SSDT + that is to be dynamically loaded by Linux. If there are + multiple variables with the same name but with different + vendor GUIDs, all of them will be loaded. See + Documentation/admin-guide/acpi/ssdt-overlays.rst for details. + + + eisa_irq_edge= [PARISC,HW] + See header of drivers/parisc/eisa.c. + + ekgdboc= [X86,KGDB] Allow early kernel console debugging + Format: ekgdboc=kbd + + This is designed to be used in conjunction with + the boot argument: earlyprintk=vga + + This parameter works in place of the kgdboc parameter + but can only be used if the backing tty is available + very early in the boot process. For early debugging + via a serial port see kgdboc_earlycon instead. + + elanfreq= [X86-32] + See comment before function elanfreq_setup() in + arch/x86/kernel/cpu/cpufreq/elanfreq.c. + + elfcorehdr=[size[KMG]@]offset[KMG] [IA64,PPC,SH,X86,S390] + Specifies physical address of start of kernel core + image elf header and optionally the size. Generally + kexec loader will pass this option to capture kernel. + See Documentation/admin-guide/kdump/kdump.rst for details. + + enable_mtrr_cleanup [X86] + The kernel tries to adjust MTRR layout from continuous + to discrete, to make X server driver able to add WB + entry later. This parameter enables that. + + enable_timer_pin_1 [X86] + Enable PIN 1 of APIC timer + Can be useful to work around chipset bugs + (in particular on some ATI chipsets). + The kernel tries to set a reasonable default. + + enforcing= [SELINUX] Set initial enforcing status. + Format: {"0" | "1"} + See security/selinux/Kconfig help text. + 0 -- permissive (log only, no denials). + 1 -- enforcing (deny and log). + Default value is 0. + Value can be changed at runtime via + /sys/fs/selinux/enforce. + + erst_disable [ACPI] + Disable Error Record Serialization Table (ERST) + support. + + ether= [HW,NET] Ethernet cards parameters + This option is obsoleted by the "netdev=" option, which + has equivalent usage. See its documentation for details. + + evm= [EVM] + Format: { "fix" } + Permit 'security.evm' to be updated regardless of + current integrity status. + + early_page_ext [KNL] Enforces page_ext initialization to earlier + stages so cover more early boot allocations. + Please note that as side effect some optimizations + might be disabled to achieve that (e.g. parallelized + memory initialization is disabled) so the boot process + might take longer, especially on systems with a lot of + memory. Available with CONFIG_PAGE_EXTENSION=y. + + failslab= + fail_usercopy= + fail_page_alloc= + fail_make_request=[KNL] + General fault injection mechanism. + Format: <interval>,<probability>,<space>,<times> + See also Documentation/fault-injection/. + + fb_tunnels= [NET] + Format: { initns | none } + See Documentation/admin-guide/sysctl/net.rst for + fb_tunnels_only_for_init_ns + + floppy= [HW] + See Documentation/admin-guide/blockdev/floppy.rst. + + force_pal_cache_flush + [IA-64] Avoid check_sal_cache_flush which may hang on + buggy SAL_CACHE_FLUSH implementations. Using this + parameter will force ia64_sal_cache_flush to call + ia64_pal_cache_flush instead of SAL_CACHE_FLUSH. + + forcepae [X86-32] + Forcefully enable Physical Address Extension (PAE). + Many Pentium M systems disable PAE but may have a + functionally usable PAE implementation. + Warning: use of this parameter will taint the kernel + and may cause unknown problems. + + ftrace=[tracer] + [FTRACE] will set and start the specified tracer + as early as possible in order to facilitate early + boot debugging. + + ftrace_boot_snapshot + [FTRACE] On boot up, a snapshot will be taken of the + ftrace ring buffer that can be read at: + /sys/kernel/tracing/snapshot. + This is useful if you need tracing information from kernel + boot up that is likely to be overridden by user space + start up functionality. + + ftrace_dump_on_oops[=orig_cpu] + [FTRACE] will dump the trace buffers on oops. + If no parameter is passed, ftrace will dump + buffers of all CPUs, but if you pass orig_cpu, it will + dump only the buffer of the CPU that triggered the + oops. + + ftrace_filter=[function-list] + [FTRACE] Limit the functions traced by the function + tracer at boot up. function-list is a comma-separated + list of functions. This list can be changed at run + time by the set_ftrace_filter file in the debugfs + tracing directory. + + ftrace_notrace=[function-list] + [FTRACE] Do not trace the functions specified in + function-list. This list can be changed at run time + by the set_ftrace_notrace file in the debugfs + tracing directory. + + ftrace_graph_filter=[function-list] + [FTRACE] Limit the top level callers functions traced + by the function graph tracer at boot up. + function-list is a comma-separated list of functions + that can be changed at run time by the + set_graph_function file in the debugfs tracing directory. + + ftrace_graph_notrace=[function-list] + [FTRACE] Do not trace from the functions specified in + function-list. This list is a comma-separated list of + functions that can be changed at run time by the + set_graph_notrace file in the debugfs tracing directory. + + ftrace_graph_max_depth=<uint> + [FTRACE] Used with the function graph tracer. This is + the max depth it will trace into a function. This value + can be changed at run time by the max_graph_depth file + in the tracefs tracing directory. default: 0 (no limit) + + fw_devlink= [KNL] Create device links between consumer and supplier + devices by scanning the firmware to infer the + consumer/supplier relationships. This feature is + especially useful when drivers are loaded as modules as + it ensures proper ordering of tasks like device probing + (suppliers first, then consumers), supplier boot state + clean up (only after all consumers have probed), + suspend/resume & runtime PM (consumers first, then + suppliers). + Format: { off | permissive | on | rpm } + off -- Don't create device links from firmware info. + permissive -- Create device links from firmware info + but use it only for ordering boot state clean + up (sync_state() calls). + on -- Create device links from firmware info and use it + to enforce probe and suspend/resume ordering. + rpm -- Like "on", but also use to order runtime PM. + + fw_devlink.strict=<bool> + [KNL] Treat all inferred dependencies as mandatory + dependencies. This only applies for fw_devlink=on|rpm. + Format: <bool> + + gamecon.map[2|3]= + [HW,JOY] Multisystem joystick and NES/SNES/PSX pad + support via parallel port (up to 5 devices per port) + Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5> + See also Documentation/input/devices/joystick-parport.rst + + gamma= [HW,DRM] + + gart_fix_e820= [X86-64] disable the fix e820 for K8 GART + Format: off | on + default: on + + gather_data_sampling= + [X86,INTEL] Control the Gather Data Sampling (GDS) + mitigation. + + Gather Data Sampling is a hardware vulnerability which + allows unprivileged speculative access to data which was + previously stored in vector registers. + + This issue is mitigated by default in updated microcode. + The mitigation may have a performance impact but can be + disabled. On systems without the microcode mitigation + disabling AVX serves as a mitigation. + + force: Disable AVX to mitigate systems without + microcode mitigation. No effect if the microcode + mitigation is present. Known to cause crashes in + userspace with buggy AVX enumeration. + + off: Disable GDS mitigation. + + gcov_persist= [GCOV] When non-zero (default), profiling data for + kernel modules is saved and remains accessible via + debugfs, even when the module is unloaded/reloaded. + When zero, profiling data is discarded and associated + debugfs files are removed at module unload time. + + goldfish [X86] Enable the goldfish android emulator platform. + Don't use this when you are not running on the + android emulator + + gpio-mockup.gpio_mockup_ranges + [HW] Sets the ranges of gpiochip of for this device. + Format: <start1>,<end1>,<start2>,<end2>... + gpio-mockup.gpio_mockup_named_lines + [HW] Let the driver know GPIO lines should be named. + + gpt [EFI] Forces disk with valid GPT signature but + invalid Protective MBR to be treated as GPT. If the + primary GPT is corrupted, it enables the backup/alternate + GPT to be used instead. + + grcan.enable0= [HW] Configuration of physical interface 0. Determines + the "Enable 0" bit of the configuration register. + Format: 0 | 1 + Default: 0 + grcan.enable1= [HW] Configuration of physical interface 1. Determines + the "Enable 0" bit of the configuration register. + Format: 0 | 1 + Default: 0 + grcan.select= [HW] Select which physical interface to use. + Format: 0 | 1 + Default: 0 + grcan.txsize= [HW] Sets the size of the tx buffer. + Format: <unsigned int> such that (txsize & ~0x1fffc0) == 0. + Default: 1024 + grcan.rxsize= [HW] Sets the size of the rx buffer. + Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0. + Default: 1024 + + hardened_usercopy= + [KNL] Under CONFIG_HARDENED_USERCOPY, whether + hardening is enabled for this boot. Hardened + usercopy checking is used to protect the kernel + from reading or writing beyond known memory + allocation boundaries as a proactive defense + against bounds-checking flaws in the kernel's + copy_to_user()/copy_from_user() interface. + on Perform hardened usercopy checks (default). + off Disable hardened usercopy checks. + + hardlockup_all_cpu_backtrace= + [KNL] Should the hard-lockup detector generate + backtraces on all cpus. + Format: 0 | 1 + + hashdist= [KNL,NUMA] Large hashes allocated during boot + are distributed across NUMA nodes. Defaults on + for 64-bit NUMA, off otherwise. + Format: 0 | 1 (for off | on) + + hcl= [IA-64] SGI's Hardware Graph compatibility layer + + hd= [EIDE] (E)IDE hard drive subsystem geometry + Format: <cyl>,<head>,<sect> + + hest_disable [ACPI] + Disable Hardware Error Source Table (HEST) support; + corresponding firmware-first mode error processing + logic will be disabled. + + hibernate= [HIBERNATION] + noresume Don't check if there's a hibernation image + present during boot. + nocompress Don't compress/decompress hibernation images. + no Disable hibernation and resume. + protect_image Turn on image protection during restoration + (that will set all pages holding image data + during restoration read-only). + + highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact + size of <nn>. This works even on boxes that have no + highmem otherwise. This also works to reduce highmem + size on bigger boxes. + + highres= [KNL] Enable/disable high resolution timer mode. + Valid parameters: "on", "off" + Default: "on" + + hlt [BUGS=ARM,SH] + + hostname= [KNL] Set the hostname (aka UTS nodename). + Format: <string> + This allows setting the system's hostname during early + startup. This sets the name returned by gethostname. + Using this parameter to set the hostname makes it + possible to ensure the hostname is correctly set before + any userspace processes run, avoiding the possibility + that a process may call gethostname before the hostname + has been explicitly set, resulting in the calling + process getting an incorrect result. The string must + not exceed the maximum allowed hostname length (usually + 64 characters) and will be truncated otherwise. + + hpet= [X86-32,HPET] option to control HPET usage + Format: { enable (default) | disable | force | + verbose } + disable: disable HPET and use PIT instead + force: allow force enabled of undocumented chips (ICH4, + VIA, nVidia) + verbose: show contents of HPET registers during setup + + hpet_mmap= [X86, HPET_MMAP] Allow userspace to mmap HPET + registers. Default set by CONFIG_HPET_MMAP_DEFAULT. + + hugepages= [HW] Number of HugeTLB pages to allocate at boot. + If this follows hugepagesz (below), it specifies + the number of pages of hugepagesz to be allocated. + If this is the first HugeTLB parameter on the command + line, it specifies the number of pages to allocate for + the default huge page size. If using node format, the + number of pages to allocate per-node can be specified. + See also Documentation/admin-guide/mm/hugetlbpage.rst. + Format: <integer> or (node format) + <node>:<integer>[,<node>:<integer>] + + hugepagesz= + [HW] The size of the HugeTLB pages. This is used in + conjunction with hugepages (above) to allocate huge + pages of a specific size at boot. The pair + hugepagesz=X hugepages=Y can be specified once for + each supported huge page size. Huge page sizes are + architecture dependent. See also + Documentation/admin-guide/mm/hugetlbpage.rst. + Format: size[KMG] + + hugetlb_cma= [HW,CMA] The size of a CMA area used for allocation + of gigantic hugepages. Or using node format, the size + of a CMA area per node can be specified. + Format: nn[KMGTPE] or (node format) + <node>:nn[KMGTPE][,<node>:nn[KMGTPE]] + + Reserve a CMA area of given size and allocate gigantic + hugepages using the CMA allocator. If enabled, the + boot-time allocation of gigantic hugepages is skipped. + + hugetlb_free_vmemmap= + [KNL] Reguires CONFIG_HUGETLB_PAGE_OPTIMIZE_VMEMMAP + enabled. + Control if HugeTLB Vmemmap Optimization (HVO) is enabled. + Allows heavy hugetlb users to free up some more + memory (7 * PAGE_SIZE for each 2MB hugetlb page). + Format: { on | off (default) } + + on: enable HVO + off: disable HVO + + Built with CONFIG_HUGETLB_PAGE_OPTIMIZE_VMEMMAP_DEFAULT_ON=y, + the default is on. + + Note that the vmemmap pages may be allocated from the added + memory block itself when memory_hotplug.memmap_on_memory is + enabled, those vmemmap pages cannot be optimized even if this + feature is enabled. Other vmemmap pages not allocated from + the added memory block itself do not be affected. + + hung_task_panic= + [KNL] Should the hung task detector generate panics. + Format: 0 | 1 + + A value of 1 instructs the kernel to panic when a + hung task is detected. The default value is controlled + by the CONFIG_BOOTPARAM_HUNG_TASK_PANIC build-time + option. The value selected by this boot parameter can + be changed later by the kernel.hung_task_panic sysctl. + + hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC) + terminal devices. Valid values: 0..8 + hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs. + If specified, z/VM IUCV HVC accepts connections + from listed z/VM user IDs only. + + hv_nopvspin [X86,HYPER_V] Disables the paravirt spinlock optimizations + which allow the hypervisor to 'idle' the + guest on lock contention. + + keep_bootcon [KNL] + Do not unregister boot console at start. This is only + useful for debugging when something happens in the window + between unregistering the boot console and initializing + the real console. + + i2c_bus= [HW] Override the default board specific I2C bus speed + or register an additional I2C bus that is not + registered from board initialization code. + Format: + <bus_id>,<clkrate> + + i8042.debug [HW] Toggle i8042 debug mode + i8042.unmask_kbd_data + [HW] Enable printing of interrupt data from the KBD port + (disabled by default, and as a pre-condition + requires that i8042.debug=1 be enabled) + i8042.direct [HW] Put keyboard port into non-translated mode + i8042.dumbkbd [HW] Pretend that controller can only read data from + keyboard and cannot control its state + (Don't attempt to blink the leds) + i8042.noaux [HW] Don't check for auxiliary (== mouse) port + i8042.nokbd [HW] Don't check/create keyboard port + i8042.noloop [HW] Disable the AUX Loopback command while probing + for the AUX port + i8042.nomux [HW] Don't check presence of an active multiplexing + controller + i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX + controllers + i8042.notimeout [HW] Ignore timeout condition signalled by controller + i8042.reset [HW] Reset the controller during init, cleanup and + suspend-to-ram transitions, only during s2r + transitions, or never reset + Format: { 1 | Y | y | 0 | N | n } + 1, Y, y: always reset controller + 0, N, n: don't ever reset controller + Default: only on s2r transitions on x86; most other + architectures force reset to be always executed + i8042.unlock [HW] Unlock (ignore) the keylock + i8042.kbdreset [HW] Reset device connected to KBD port + i8042.probe_defer + [HW] Allow deferred probing upon i8042 probe errors + + i810= [HW,DRM] + + i915.invert_brightness= + [DRM] Invert the sense of the variable that is used to + set the brightness of the panel backlight. Normally a + brightness value of 0 indicates backlight switched off, + and the maximum of the brightness value sets the backlight + to maximum brightness. If this parameter is set to 0 + (default) and the machine requires it, or this parameter + is set to 1, a brightness value of 0 sets the backlight + to maximum brightness, and the maximum of the brightness + value switches the backlight off. + -1 -- never invert brightness + 0 -- machine default + 1 -- force brightness inversion + + icn= [HW,ISDN] + Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] + + + idle= [X86] + Format: idle=poll, idle=halt, idle=nomwait + Poll forces a polling idle loop that can slightly + improve the performance of waking up a idle CPU, but + will use a lot of power and make the system run hot. + Not recommended. + idle=halt: Halt is forced to be used for CPU idle. + In such case C2/C3 won't be used again. + idle=nomwait: Disable mwait for CPU C-states + + idxd.sva= [HW] + Format: <bool> + Allow force disabling of Shared Virtual Memory (SVA) + support for the idxd driver. By default it is set to + true (1). + + idxd.tc_override= [HW] + Format: <bool> + Allow override of default traffic class configuration + for the device. By default it is set to false (0). + + ieee754= [MIPS] Select IEEE Std 754 conformance mode + Format: { strict | legacy | 2008 | relaxed } + Default: strict + + Choose which programs will be accepted for execution + based on the IEEE 754 NaN encoding(s) supported by + the FPU and the NaN encoding requested with the value + of an ELF file header flag individually set by each + binary. Hardware implementations are permitted to + support either or both of the legacy and the 2008 NaN + encoding mode. + + Available settings are as follows: + strict accept binaries that request a NaN encoding + supported by the FPU + legacy only accept legacy-NaN binaries, if supported + by the FPU + 2008 only accept 2008-NaN binaries, if supported + by the FPU + relaxed accept any binaries regardless of whether + supported by the FPU + + The FPU emulator is always able to support both NaN + encodings, so if no FPU hardware is present or it has + been disabled with 'nofpu', then the settings of + 'legacy' and '2008' strap the emulator accordingly, + 'relaxed' straps the emulator for both legacy-NaN and + 2008-NaN, whereas 'strict' enables legacy-NaN only on + legacy processors and both NaN encodings on MIPS32 or + MIPS64 CPUs. + + The setting for ABS.fmt/NEG.fmt instruction execution + mode generally follows that for the NaN encoding, + except where unsupported by hardware. + + ignore_loglevel [KNL] + Ignore loglevel setting - this will print /all/ + kernel messages to the console. Useful for debugging. + We also add it as printk module parameter, so users + could change it dynamically, usually by + /sys/module/printk/parameters/ignore_loglevel. + + ignore_rlimit_data + Ignore RLIMIT_DATA setting for data mappings, + print warning at first misuse. Can be changed via + /sys/module/kernel/parameters/ignore_rlimit_data. + + ihash_entries= [KNL] + Set number of hash buckets for inode cache. + + ima_appraise= [IMA] appraise integrity measurements + Format: { "off" | "enforce" | "fix" | "log" } + default: "enforce" + + ima_appraise_tcb [IMA] Deprecated. Use ima_policy= instead. + The builtin appraise policy appraises all files + owned by uid=0. + + ima_canonical_fmt [IMA] + Use the canonical format for the binary runtime + measurements, instead of host native format. + + ima_hash= [IMA] + Format: { md5 | sha1 | rmd160 | sha256 | sha384 + | sha512 | ... } + default: "sha1" + + The list of supported hash algorithms is defined + in crypto/hash_info.h. + + ima_policy= [IMA] + The builtin policies to load during IMA setup. + Format: "tcb | appraise_tcb | secure_boot | + fail_securely | critical_data" + + The "tcb" policy measures all programs exec'd, files + mmap'd for exec, and all files opened with the read + mode bit set by either the effective uid (euid=0) or + uid=0. + + The "appraise_tcb" policy appraises the integrity of + all files owned by root. + + The "secure_boot" policy appraises the integrity + of files (eg. kexec kernel image, kernel modules, + firmware, policy, etc) based on file signatures. + + The "fail_securely" policy forces file signature + verification failure also on privileged mounted + filesystems with the SB_I_UNVERIFIABLE_SIGNATURE + flag. + + The "critical_data" policy measures kernel integrity + critical data. + + ima_tcb [IMA] Deprecated. Use ima_policy= instead. + Load a policy which meets the needs of the Trusted + Computing Base. This means IMA will measure all + programs exec'd, files mmap'd for exec, and all files + opened for read by uid=0. + + ima_template= [IMA] + Select one of defined IMA measurements template formats. + Formats: { "ima" | "ima-ng" | "ima-ngv2" | "ima-sig" | + "ima-sigv2" } + Default: "ima-ng" + + ima_template_fmt= + [IMA] Define a custom template format. + Format: { "field1|...|fieldN" } + + ima.ahash_minsize= [IMA] Minimum file size for asynchronous hash usage + Format: <min_file_size> + Set the minimal file size for using asynchronous hash. + If left unspecified, ahash usage is disabled. + + ahash performance varies for different data sizes on + different crypto accelerators. This option can be used + to achieve the best performance for a particular HW. + + ima.ahash_bufsize= [IMA] Asynchronous hash buffer size + Format: <bufsize> + Set hashing buffer size. Default: 4k. + + ahash performance varies for different chunk sizes on + different crypto accelerators. This option can be used + to achieve best performance for particular HW. + + init= [KNL] + Format: <full_path> + Run specified binary instead of /sbin/init as init + process. + + initcall_debug [KNL] Trace initcalls as they are executed. Useful + for working out where the kernel is dying during + startup. + + initcall_blacklist= [KNL] Do not execute a comma-separated list of + initcall functions. Useful for debugging built-in + modules and initcalls. + + initramfs_async= [KNL] + Format: <bool> + Default: 1 + This parameter controls whether the initramfs + image is unpacked asynchronously, concurrently + with devices being probed and + initialized. This should normally just work, + but as a debugging aid, one can get the + historical behaviour of the initramfs + unpacking being completed before device_ and + late_ initcalls. + + initrd= [BOOT] Specify the location of the initial ramdisk + + initrdmem= [KNL] Specify a physical address and size from which to + load the initrd. If an initrd is compiled in or + specified in the bootparams, it takes priority over this + setting. + Format: ss[KMG],nn[KMG] + Default is 0, 0 + + init_on_alloc= [MM] Fill newly allocated pages and heap objects with + zeroes. + Format: 0 | 1 + Default set by CONFIG_INIT_ON_ALLOC_DEFAULT_ON. + + init_on_free= [MM] Fill freed pages and heap objects with zeroes. + Format: 0 | 1 + Default set by CONFIG_INIT_ON_FREE_DEFAULT_ON. + + init_pkru= [X86] Specify the default memory protection keys rights + register contents for all processes. 0x55555554 by + default (disallow access to all but pkey 0). Can + override in debugfs after boot. + + inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver + Format: <irq> + + int_pln_enable [X86] Enable power limit notification interrupt + + integrity_audit=[IMA] + Format: { "0" | "1" } + 0 -- basic integrity auditing messages. (Default) + 1 -- additional integrity auditing messages. + + intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option + on + Enable intel iommu driver. + off + Disable intel iommu driver. + igfx_off [Default Off] + By default, gfx is mapped as normal device. If a gfx + device has a dedicated DMAR unit, the DMAR unit is + bypassed by not enabling DMAR with this option. In + this case, gfx device will use physical address for + DMA. + strict [Default Off] + Deprecated, equivalent to iommu.strict=1. + sp_off [Default Off] + By default, super page will be supported if Intel IOMMU + has the capability. With this option, super page will + not be supported. + sm_on + Enable the Intel IOMMU scalable mode if the hardware + advertises that it has support for the scalable mode + translation. + sm_off + Disallow use of the Intel IOMMU scalable mode. + tboot_noforce [Default Off] + Do not force the Intel IOMMU enabled under tboot. + By default, tboot will force Intel IOMMU on, which + could harm performance of some high-throughput + devices like 40GBit network cards, even if identity + mapping is enabled. + Note that using this option lowers the security + provided by tboot because it makes the system + vulnerable to DMA attacks. + + intel_idle.max_cstate= [KNL,HW,ACPI,X86] + 0 disables intel_idle and fall back on acpi_idle. + 1 to 9 specify maximum depth of C-state. + + intel_pstate= [X86] + disable + Do not enable intel_pstate as the default + scaling driver for the supported processors + passive + Use intel_pstate as a scaling driver, but configure it + to work with generic cpufreq governors (instead of + enabling its internal governor). This mode cannot be + used along with the hardware-managed P-states (HWP) + feature. + force + Enable intel_pstate on systems that prohibit it by default + in favor of acpi-cpufreq. Forcing the intel_pstate driver + instead of acpi-cpufreq may disable platform features, such + as thermal controls and power capping, that rely on ACPI + P-States information being indicated to OSPM and therefore + should be used with caution. This option does not work with + processors that aren't supported by the intel_pstate driver + or on platforms that use pcc-cpufreq instead of acpi-cpufreq. + no_hwp + Do not enable hardware P state control (HWP) + if available. + hwp_only + Only load intel_pstate on systems which support + hardware P state control (HWP) if available. + support_acpi_ppc + Enforce ACPI _PPC performance limits. If the Fixed ACPI + Description Table, specifies preferred power management + profile as "Enterprise Server" or "Performance Server", + then this feature is turned on by default. + per_cpu_perf_limits + Allow per-logical-CPU P-State performance control limits using + cpufreq sysfs interface + + intremap= [X86-64, Intel-IOMMU] + on enable Interrupt Remapping (default) + off disable Interrupt Remapping + nosid disable Source ID checking + no_x2apic_optout + BIOS x2APIC opt-out request will be ignored + nopost disable Interrupt Posting + + iomem= Disable strict checking of access to MMIO memory + strict regions from userspace. + relaxed + + iommu= [X86] + off + force + noforce + biomerge + panic + nopanic + merge + nomerge + soft + pt [X86] + nopt [X86] + nobypass [PPC/POWERNV] + Disable IOMMU bypass, using IOMMU for PCI devices. + + iommu.forcedac= [ARM64, X86] Control IOVA allocation for PCI devices. + Format: { "0" | "1" } + 0 - Try to allocate a 32-bit DMA address first, before + falling back to the full range if needed. + 1 - Allocate directly from the full usable range, + forcing Dual Address Cycle for PCI cards supporting + greater than 32-bit addressing. + + iommu.strict= [ARM64, X86] Configure TLB invalidation behaviour + Format: { "0" | "1" } + 0 - Lazy mode. + Request that DMA unmap operations use deferred + invalidation of hardware TLBs, for increased + throughput at the cost of reduced device isolation. + Will fall back to strict mode if not supported by + the relevant IOMMU driver. + 1 - Strict mode. + DMA unmap operations invalidate IOMMU hardware TLBs + synchronously. + unset - Use value of CONFIG_IOMMU_DEFAULT_DMA_{LAZY,STRICT}. + Note: on x86, strict mode specified via one of the + legacy driver-specific options takes precedence. + + iommu.passthrough= + [ARM64, X86] Configure DMA to bypass the IOMMU by default. + Format: { "0" | "1" } + 0 - Use IOMMU translation for DMA. + 1 - Bypass the IOMMU for DMA. + unset - Use value of CONFIG_IOMMU_DEFAULT_PASSTHROUGH. + + io7= [HW] IO7 for Marvel-based Alpha systems + See comment before marvel_specify_io7 in + arch/alpha/kernel/core_marvel.c. + + io_delay= [X86] I/O delay method + 0x80 + Standard port 0x80 based delay + 0xed + Alternate port 0xed based delay (needed on some systems) + udelay + Simple two microseconds delay + none + No delay + + ip= [IP_PNP] + See Documentation/admin-guide/nfs/nfsroot.rst. + + ipcmni_extend [KNL] Extend the maximum number of unique System V + IPC identifiers from 32,768 to 16,777,216. + + irqaffinity= [SMP] Set the default irq affinity mask + The argument is a cpu list, as described above. + + irqchip.gicv2_force_probe= + [ARM, ARM64] + Format: <bool> + Force the kernel to look for the second 4kB page + of a GICv2 controller even if the memory range + exposed by the device tree is too small. + + irqchip.gicv3_nolpi= + [ARM, ARM64] + Force the kernel to ignore the availability of + LPIs (and by consequence ITSs). Intended for system + that use the kernel as a bootloader, and thus want + to let secondary kernels in charge of setting up + LPIs. + + irqchip.gicv3_pseudo_nmi= [ARM64] + Enables support for pseudo-NMIs in the kernel. This + requires the kernel to be built with + CONFIG_ARM64_PSEUDO_NMI. + + irqfixup [HW] + When an interrupt is not handled search all handlers + for it. Intended to get systems with badly broken + firmware running. + + irqpoll [HW] + When an interrupt is not handled search all handlers + for it. Also check all handlers each timer + interrupt. Intended to get systems with badly broken + firmware running. + + isapnp= [ISAPNP] + Format: <RDP>,<reset>,<pci_scan>,<verbosity> + + isolcpus= [KNL,SMP,ISOL] Isolate a given set of CPUs from disturbance. + [Deprecated - use cpusets instead] + Format: [flag-list,]<cpu-list> + + Specify one or more CPUs to isolate from disturbances + specified in the flag list (default: domain): + + nohz + Disable the tick when a single task runs. + + A residual 1Hz tick is offloaded to workqueues, which you + need to affine to housekeeping through the global + workqueue's affinity configured via the + /sys/devices/virtual/workqueue/cpumask sysfs file, or + by using the 'domain' flag described below. + + NOTE: by default the global workqueue runs on all CPUs, + so to protect individual CPUs the 'cpumask' file has to + be configured manually after bootup. + + domain + Isolate from the general SMP balancing and scheduling + algorithms. Note that performing domain isolation this way + is irreversible: it's not possible to bring back a CPU to + the domains once isolated through isolcpus. It's strongly + advised to use cpusets instead to disable scheduler load + balancing through the "cpuset.sched_load_balance" file. + It offers a much more flexible interface where CPUs can + move in and out of an isolated set anytime. + + You can move a process onto or off an "isolated" CPU via + the CPU affinity syscalls or cpuset. + <cpu number> begins at 0 and the maximum value is + "number of CPUs in system - 1". + + managed_irq + + Isolate from being targeted by managed interrupts + which have an interrupt mask containing isolated + CPUs. The affinity of managed interrupts is + handled by the kernel and cannot be changed via + the /proc/irq/* interfaces. + + This isolation is best effort and only effective + if the automatically assigned interrupt mask of a + device queue contains isolated and housekeeping + CPUs. If housekeeping CPUs are online then such + interrupts are directed to the housekeeping CPU + so that IO submitted on the housekeeping CPU + cannot disturb the isolated CPU. + + If a queue's affinity mask contains only isolated + CPUs then this parameter has no effect on the + interrupt routing decision, though interrupts are + only delivered when tasks running on those + isolated CPUs submit IO. IO submitted on + housekeeping CPUs has no influence on those + queues. + + The format of <cpu-list> is described above. + + iucv= [HW,NET] + + ivrs_ioapic [HW,X86-64] + Provide an override to the IOAPIC-ID<->DEVICE-ID + mapping provided in the IVRS ACPI table. + By default, PCI segment is 0, and can be omitted. + + For example, to map IOAPIC-ID decimal 10 to + PCI segment 0x1 and PCI device 00:14.0, + write the parameter as: + ivrs_ioapic=10@0001:00:14.0 + + Deprecated formats: + * To map IOAPIC-ID decimal 10 to PCI device 00:14.0 + write the parameter as: + ivrs_ioapic[10]=00:14.0 + * To map IOAPIC-ID decimal 10 to PCI segment 0x1 and + PCI device 00:14.0 write the parameter as: + ivrs_ioapic[10]=0001:00:14.0 + + ivrs_hpet [HW,X86-64] + Provide an override to the HPET-ID<->DEVICE-ID + mapping provided in the IVRS ACPI table. + By default, PCI segment is 0, and can be omitted. + + For example, to map HPET-ID decimal 10 to + PCI segment 0x1 and PCI device 00:14.0, + write the parameter as: + ivrs_hpet=10@0001:00:14.0 + + Deprecated formats: + * To map HPET-ID decimal 0 to PCI device 00:14.0 + write the parameter as: + ivrs_hpet[0]=00:14.0 + * To map HPET-ID decimal 10 to PCI segment 0x1 and + PCI device 00:14.0 write the parameter as: + ivrs_ioapic[10]=0001:00:14.0 + + ivrs_acpihid [HW,X86-64] + Provide an override to the ACPI-HID:UID<->DEVICE-ID + mapping provided in the IVRS ACPI table. + By default, PCI segment is 0, and can be omitted. + + For example, to map UART-HID:UID AMD0020:0 to + PCI segment 0x1 and PCI device ID 00:14.5, + write the parameter as: + ivrs_acpihid=AMD0020:0@0001:00:14.5 + + Deprecated formats: + * To map UART-HID:UID AMD0020:0 to PCI segment is 0, + PCI device ID 00:14.5, write the parameter as: + ivrs_acpihid[00:14.5]=AMD0020:0 + * To map UART-HID:UID AMD0020:0 to PCI segment 0x1 and + PCI device ID 00:14.5, write the parameter as: + ivrs_acpihid[0001:00:14.5]=AMD0020:0 + + js= [HW,JOY] Analog joystick + See Documentation/input/joydev/joystick.rst. + + nokaslr [KNL] + When CONFIG_RANDOMIZE_BASE is set, this disables + kernel and module base offset ASLR (Address Space + Layout Randomization). + + kasan_multi_shot + [KNL] Enforce KASAN (Kernel Address Sanitizer) to print + report on every invalid memory access. Without this + parameter KASAN will print report only for the first + invalid access. + + keepinitrd [HW,ARM] + + kernelcore= [KNL,X86,IA-64,PPC] + Format: nn[KMGTPE] | nn% | "mirror" + This parameter specifies the amount of memory usable by + the kernel for non-movable allocations. The requested + amount is spread evenly throughout all nodes in the + system as ZONE_NORMAL. The remaining memory is used for + movable memory in its own zone, ZONE_MOVABLE. In the + event, a node is too small to have both ZONE_NORMAL and + ZONE_MOVABLE, kernelcore memory will take priority and + other nodes will have a larger ZONE_MOVABLE. + + ZONE_MOVABLE is used for the allocation of pages that + may be reclaimed or moved by the page migration + subsystem. Note that allocations like PTEs-from-HighMem + still use the HighMem zone if it exists, and the Normal + zone if it does not. + + It is possible to specify the exact amount of memory in + the form of "nn[KMGTPE]", a percentage of total system + memory in the form of "nn%", or "mirror". If "mirror" + option is specified, mirrored (reliable) memory is used + for non-movable allocations and remaining memory is used + for Movable pages. "nn[KMGTPE]", "nn%", and "mirror" + are exclusive, so you cannot specify multiple forms. + + kgdbdbgp= [KGDB,HW] kgdb over EHCI usb debug port. + Format: <Controller#>[,poll interval] + The controller # is the number of the ehci usb debug + port as it is probed via PCI. The poll interval is + optional and is the number seconds in between + each poll cycle to the debug port in case you need + the functionality for interrupting the kernel with + gdb or control-c on the dbgp connection. When + not using this parameter you use sysrq-g to break into + the kernel debugger. + + kgdboc= [KGDB,HW] kgdb over consoles. + Requires a tty driver that supports console polling, + or a supported polling keyboard driver (non-usb). + Serial only format: <serial_device>[,baud] + keyboard only format: kbd + keyboard and serial format: kbd,<serial_device>[,baud] + Optional Kernel mode setting: + kms, kbd format: kms,kbd + kms, kbd and serial format: kms,kbd,<ser_dev>[,baud] + + kgdboc_earlycon= [KGDB,HW] + If the boot console provides the ability to read + characters and can work in polling mode, you can use + this parameter to tell kgdb to use it as a backend + until the normal console is registered. Intended to + be used together with the kgdboc parameter which + specifies the normal console to transition to. + + The name of the early console should be specified + as the value of this parameter. Note that the name of + the early console might be different than the tty + name passed to kgdboc. It's OK to leave the value + blank and the first boot console that implements + read() will be picked. + + kgdbwait [KGDB] Stop kernel execution and enter the + kernel debugger at the earliest opportunity. + + kmac= [MIPS] Korina ethernet MAC address. + Configure the RouterBoard 532 series on-chip + Ethernet adapter MAC address. + + kmemleak= [KNL] Boot-time kmemleak enable/disable + Valid arguments: on, off + Default: on + Built with CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF=y, + the default is off. + + kprobe_event=[probe-list] + [FTRACE] Add kprobe events and enable at boot time. + The probe-list is a semicolon delimited list of probe + definitions. Each definition is same as kprobe_events + interface, but the parameters are comma delimited. + For example, to add a kprobe event on vfs_read with + arg1 and arg2, add to the command line; + + kprobe_event=p,vfs_read,$arg1,$arg2 + + See also Documentation/trace/kprobetrace.rst "Kernel + Boot Parameter" section. + + kpti= [ARM64] Control page table isolation of user + and kernel address spaces. + Default: enabled on cores which need mitigation. + 0: force disabled + 1: force enabled + + kunit.enable= [KUNIT] Enable executing KUnit tests. Requires + CONFIG_KUNIT to be set to be fully enabled. The + default value can be overridden via + KUNIT_DEFAULT_ENABLED. + Default is 1 (enabled) + + kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs. + Default is 0 (don't ignore, but inject #GP) + + kvm.eager_page_split= + [KVM,X86] Controls whether or not KVM will try to + proactively split all huge pages during dirty logging. + Eager page splitting reduces interruptions to vCPU + execution by eliminating the write-protection faults + and MMU lock contention that would otherwise be + required to split huge pages lazily. + + VM workloads that rarely perform writes or that write + only to a small region of VM memory may benefit from + disabling eager page splitting to allow huge pages to + still be used for reads. + + The behavior of eager page splitting depends on whether + KVM_DIRTY_LOG_INITIALLY_SET is enabled or disabled. If + disabled, all huge pages in a memslot will be eagerly + split when dirty logging is enabled on that memslot. If + enabled, eager page splitting will be performed during + the KVM_CLEAR_DIRTY ioctl, and only for the pages being + cleared. + + Eager page splitting is only supported when kvm.tdp_mmu=Y. + + Default is Y (on). + + kvm.enable_vmware_backdoor=[KVM] Support VMware backdoor PV interface. + Default is false (don't support). + + kvm.nx_huge_pages= + [KVM] Controls the software workaround for the + X86_BUG_ITLB_MULTIHIT bug. + force : Always deploy workaround. + off : Never deploy workaround. + auto : Deploy workaround based on the presence of + X86_BUG_ITLB_MULTIHIT. + + Default is 'auto'. + + If the software workaround is enabled for the host, + guests do need not to enable it for nested guests. + + kvm.nx_huge_pages_recovery_ratio= + [KVM] Controls how many 4KiB pages are periodically zapped + back to huge pages. 0 disables the recovery, otherwise if + the value is N KVM will zap 1/Nth of the 4KiB pages every + period (see below). The default is 60. + + kvm.nx_huge_pages_recovery_period_ms= + [KVM] Controls the time period at which KVM zaps 4KiB pages + back to huge pages. If the value is a non-zero N, KVM will + zap a portion (see ratio above) of the pages every N msecs. + If the value is 0 (the default), KVM will pick a period based + on the ratio, such that a page is zapped after 1 hour on average. + + kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM. + Default is 1 (enabled) + + kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU) + for all guests. + Default is 1 (enabled) if in 64-bit or 32-bit PAE mode. + + kvm-arm.mode= + [KVM,ARM] Select one of KVM/arm64's modes of operation. + + none: Forcefully disable KVM. + + nvhe: Standard nVHE-based mode, without support for + protected guests. + + protected: nVHE-based mode with support for guests whose + state is kept private from the host. + + Defaults to VHE/nVHE based on hardware support. Setting + mode to "protected" will disable kexec and hibernation + for the host. + + kvm-arm.vgic_v3_group0_trap= + [KVM,ARM] Trap guest accesses to GICv3 group-0 + system registers + + kvm-arm.vgic_v3_group1_trap= + [KVM,ARM] Trap guest accesses to GICv3 group-1 + system registers + + kvm-arm.vgic_v3_common_trap= + [KVM,ARM] Trap guest accesses to GICv3 common + system registers + + kvm-arm.vgic_v4_enable= + [KVM,ARM] Allow use of GICv4 for direct injection of + LPIs. + + kvm_cma_resv_ratio=n [PPC] + Reserves given percentage from system memory area for + contiguous memory allocation for KVM hash pagetable + allocation. + By default it reserves 5% of total system memory. + Format: <integer> + Default: 5 + + kvm-intel.ept= [KVM,Intel] Disable extended page tables + (virtualized MMU) support on capable Intel chips. + Default is 1 (enabled) + + kvm-intel.emulate_invalid_guest_state= + [KVM,Intel] Disable emulation of invalid guest state. + Ignored if kvm-intel.enable_unrestricted_guest=1, as + guest state is never invalid for unrestricted guests. + This param doesn't apply to nested guests (L2), as KVM + never emulates invalid L2 guest state. + Default is 1 (enabled) + + kvm-intel.flexpriority= + [KVM,Intel] Disable FlexPriority feature (TPR shadow). + Default is 1 (enabled) + + kvm-intel.nested= + [KVM,Intel] Enable VMX nesting (nVMX). + Default is 0 (disabled) + + kvm-intel.unrestricted_guest= + [KVM,Intel] Disable unrestricted guest feature + (virtualized real and unpaged mode) on capable + Intel chips. Default is 1 (enabled) + + kvm-intel.vmentry_l1d_flush=[KVM,Intel] Mitigation for L1 Terminal Fault + CVE-2018-3620. + + Valid arguments: never, cond, always + + always: L1D cache flush on every VMENTER. + cond: Flush L1D on VMENTER only when the code between + VMEXIT and VMENTER can leak host memory. + never: Disables the mitigation + + Default is cond (do L1 cache flush in specific instances) + + kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification + feature (tagged TLBs) on capable Intel chips. + Default is 1 (enabled) + + l1d_flush= [X86,INTEL] + Control mitigation for L1D based snooping vulnerability. + + Certain CPUs are vulnerable to an exploit against CPU + internal buffers which can forward information to a + disclosure gadget under certain conditions. + + In vulnerable processors, the speculatively + forwarded data can be used in a cache side channel + attack, to access data to which the attacker does + not have direct access. + + This parameter controls the mitigation. The + options are: + + on - enable the interface for the mitigation + + l1tf= [X86] Control mitigation of the L1TF vulnerability on + affected CPUs + + The kernel PTE inversion protection is unconditionally + enabled and cannot be disabled. + + full + Provides all available mitigations for the + L1TF vulnerability. Disables SMT and + enables all mitigations in the + hypervisors, i.e. unconditional L1D flush. + + SMT control and L1D flush control via the + sysfs interface is still possible after + boot. Hypervisors will issue a warning + when the first VM is started in a + potentially insecure configuration, + i.e. SMT enabled or L1D flush disabled. + + full,force + Same as 'full', but disables SMT and L1D + flush runtime control. Implies the + 'nosmt=force' command line option. + (i.e. sysfs control of SMT is disabled.) + + flush + Leaves SMT enabled and enables the default + hypervisor mitigation, i.e. conditional + L1D flush. + + SMT control and L1D flush control via the + sysfs interface is still possible after + boot. Hypervisors will issue a warning + when the first VM is started in a + potentially insecure configuration, + i.e. SMT enabled or L1D flush disabled. + + flush,nosmt + + Disables SMT and enables the default + hypervisor mitigation. + + SMT control and L1D flush control via the + sysfs interface is still possible after + boot. Hypervisors will issue a warning + when the first VM is started in a + potentially insecure configuration, + i.e. SMT enabled or L1D flush disabled. + + flush,nowarn + Same as 'flush', but hypervisors will not + warn when a VM is started in a potentially + insecure configuration. + + off + Disables hypervisor mitigations and doesn't + emit any warnings. + It also drops the swap size and available + RAM limit restriction on both hypervisor and + bare metal. + + Default is 'flush'. + + For details see: Documentation/admin-guide/hw-vuln/l1tf.rst + + l2cr= [PPC] + + l3cr= [PPC] + + lapic [X86-32,APIC] Enable the local APIC even if BIOS + disabled it. + + lapic= [X86,APIC] Do not use TSC deadline + value for LAPIC timer one-shot implementation. Default + back to the programmable timer unit in the LAPIC. + Format: notscdeadline + + lapic_timer_c2_ok [X86,APIC] trust the local apic timer + in C2 power state. + + libata.dma= [LIBATA] DMA control + libata.dma=0 Disable all PATA and SATA DMA + libata.dma=1 PATA and SATA Disk DMA only + libata.dma=2 ATAPI (CDROM) DMA only + libata.dma=4 Compact Flash DMA only + Combinations also work, so libata.dma=3 enables DMA + for disks and CDROMs, but not CFs. + + libata.ignore_hpa= [LIBATA] Ignore HPA limit + libata.ignore_hpa=0 keep BIOS limits (default) + libata.ignore_hpa=1 ignore limits, using full disk + + libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume + when set. + Format: <int> + + libata.force= [LIBATA] Force configurations. The format is a comma- + separated list of "[ID:]VAL" where ID is PORT[.DEVICE]. + PORT and DEVICE are decimal numbers matching port, link + or device. Basically, it matches the ATA ID string + printed on console by libata. If the whole ID part is + omitted, the last PORT and DEVICE values are used. If + ID hasn't been specified yet, the configuration applies + to all ports, links and devices. + + If only DEVICE is omitted, the parameter applies to + the port and all links and devices behind it. DEVICE + number of 0 either selects the first device or the + first fan-out link behind PMP device. It does not + select the host link. DEVICE number of 15 selects the + host link and device attached to it. + + The VAL specifies the configuration to force. As long + as there is no ambiguity, shortcut notation is allowed. + For example, both 1.5 and 1.5G would work for 1.5Gbps. + The following configurations can be forced. + + * Cable type: 40c, 80c, short40c, unk, ign or sata. + Any ID with matching PORT is used. + + * SATA link speed limit: 1.5Gbps or 3.0Gbps. + + * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7]. + udma[/][16,25,33,44,66,100,133] notation is also + allowed. + + * nohrst, nosrst, norst: suppress hard, soft and both + resets. + + * rstonce: only attempt one reset during hot-unplug + link recovery. + + * [no]dbdelay: Enable or disable the extra 200ms delay + before debouncing a link PHY and device presence + detection. + + * [no]ncq: Turn on or off NCQ. + + * [no]ncqtrim: Enable or disable queued DSM TRIM. + + * [no]ncqati: Enable or disable NCQ trim on ATI chipset. + + * [no]trim: Enable or disable (unqueued) TRIM. + + * trim_zero: Indicate that TRIM command zeroes data. + + * max_trim_128m: Set 128M maximum trim size limit. + + * [no]dma: Turn on or off DMA transfers. + + * atapi_dmadir: Enable ATAPI DMADIR bridge support. + + * atapi_mod16_dma: Enable the use of ATAPI DMA for + commands that are not a multiple of 16 bytes. + + * [no]dmalog: Enable or disable the use of the + READ LOG DMA EXT command to access logs. + + * [no]iddevlog: Enable or disable access to the + identify device data log. + + * [no]logdir: Enable or disable access to the general + purpose log directory. + + * max_sec_128: Set transfer size limit to 128 sectors. + + * max_sec_1024: Set or clear transfer size limit to + 1024 sectors. + + * max_sec_lba48: Set or clear transfer size limit to + 65535 sectors. + + * [no]lpm: Enable or disable link power management. + + * [no]setxfer: Indicate if transfer speed mode setting + should be skipped. + + * dump_id: Dump IDENTIFY data. + + * disable: Disable this device. + + If there are multiple matching configurations changing + the same attribute, the last one is used. + + load_ramdisk= [RAM] [Deprecated] + + lockd.nlm_grace_period=P [NFS] Assign grace period. + Format: <integer> + + lockd.nlm_tcpport=N [NFS] Assign TCP port. + Format: <integer> + + lockd.nlm_timeout=T [NFS] Assign timeout value. + Format: <integer> + + lockd.nlm_udpport=M [NFS] Assign UDP port. + Format: <integer> + + lockdown= [SECURITY] + { integrity | confidentiality } + Enable the kernel lockdown feature. If set to + integrity, kernel features that allow userland to + modify the running kernel are disabled. If set to + confidentiality, kernel features that allow userland + to extract confidential information from the kernel + are also disabled. + + locktorture.nreaders_stress= [KNL] + Set the number of locking read-acquisition kthreads. + Defaults to being automatically set based on the + number of online CPUs. + + locktorture.nwriters_stress= [KNL] + Set the number of locking write-acquisition kthreads. + + locktorture.onoff_holdoff= [KNL] + Set time (s) after boot for CPU-hotplug testing. + + locktorture.onoff_interval= [KNL] + Set time (s) between CPU-hotplug operations, or + zero to disable CPU-hotplug testing. + + locktorture.shuffle_interval= [KNL] + Set task-shuffle interval (jiffies). Shuffling + tasks allows some CPUs to go into dyntick-idle + mode during the locktorture test. + + locktorture.shutdown_secs= [KNL] + Set time (s) after boot system shutdown. This + is useful for hands-off automated testing. + + locktorture.stat_interval= [KNL] + Time (s) between statistics printk()s. + + locktorture.stutter= [KNL] + Time (s) to stutter testing, for example, + specifying five seconds causes the test to run for + five seconds, wait for five seconds, and so on. + This tests the locking primitive's ability to + transition abruptly to and from idle. + + locktorture.torture_type= [KNL] + Specify the locking implementation to test. + + locktorture.verbose= [KNL] + Enable additional printk() statements. + + logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver + Format: <irq> + + loglevel= All Kernel Messages with a loglevel smaller than the + console loglevel will be printed to the console. It can + also be changed with klogd or other programs. The + loglevels are defined as follows: + + 0 (KERN_EMERG) system is unusable + 1 (KERN_ALERT) action must be taken immediately + 2 (KERN_CRIT) critical conditions + 3 (KERN_ERR) error conditions + 4 (KERN_WARNING) warning conditions + 5 (KERN_NOTICE) normal but significant condition + 6 (KERN_INFO) informational + 7 (KERN_DEBUG) debug-level messages + + log_buf_len=n[KMG] Sets the size of the printk ring buffer, + in bytes. n must be a power of two and greater + than the minimal size. The minimal size is defined + by LOG_BUF_SHIFT kernel config parameter. There is + also CONFIG_LOG_CPU_MAX_BUF_SHIFT config parameter + that allows to increase the default size depending on + the number of CPUs. See init/Kconfig for more details. + + logo.nologo [FB] Disables display of the built-in Linux logo. + This may be used to provide more screen space for + kernel log messages and is useful when debugging + kernel boot problems. + + lp=0 [LP] Specify parallel ports to use, e.g, + lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses + lp=reset first parallel port). 'lp=0' disables the + lp=auto printer driver. 'lp=reset' (which can be + specified in addition to the ports) causes + attached printers to be reset. Using + lp=port1,port2,... specifies the parallel ports + to associate lp devices with, starting with + lp0. A port specification may be 'none' to skip + that lp device, or a parport name such as + 'parport0'. Specifying 'lp=auto' instead of a + port specification list means that device IDs + from each port should be examined, to see if + an IEEE 1284-compliant printer is attached; if + so, the driver will manage that printer. + See also header of drivers/char/lp.c. + + lpj=n [KNL] + Sets loops_per_jiffy to given constant, thus avoiding + time-consuming boot-time autodetection (up to 250 ms per + CPU). 0 enables autodetection (default). To determine + the correct value for your kernel, boot with normal + autodetection and see what value is printed. Note that + on SMP systems the preset will be applied to all CPUs, + which is likely to cause problems if your CPUs need + significantly divergent settings. An incorrect value + will cause delays in the kernel to be wrong, leading to + unpredictable I/O errors and other breakage. Although + unlikely, in the extreme case this might damage your + hardware. + + ltpc= [NET] + Format: <io>,<irq>,<dma> + + lsm.debug [SECURITY] Enable LSM initialization debugging output. + + lsm=lsm1,...,lsmN + [SECURITY] Choose order of LSM initialization. This + overrides CONFIG_LSM, and the "security=" parameter. + + machvec= [IA-64] Force the use of a particular machine-vector + (machvec) in a generic kernel. + Example: machvec=hpzx1 + + machtype= [Loongson] Share the same kernel image file between + different yeeloong laptops. + Example: machtype=lemote-yeeloong-2f-7inch + + max_addr=nn[KMG] [KNL,BOOT,IA-64] All physical memory greater + than or equal to this physical address is ignored. + + maxcpus= [SMP] Maximum number of processors that an SMP kernel + will bring up during bootup. maxcpus=n : n >= 0 limits + the kernel to bring up 'n' processors. Surely after + bootup you can bring up the other plugged cpu by executing + "echo 1 > /sys/devices/system/cpu/cpuX/online". So maxcpus + only takes effect during system bootup. + While n=0 is a special case, it is equivalent to "nosmp", + which also disables the IO APIC. + + max_loop= [LOOP] The number of loop block devices that get + (loop.max_loop) unconditionally pre-created at init time. The default + number is configured by BLK_DEV_LOOP_MIN_COUNT. Instead + of statically allocating a predefined number, loop + devices can be requested on-demand with the + /dev/loop-control interface. + + mce [X86-32] Machine Check Exception + + mce=option [X86-64] See Documentation/x86/x86_64/boot-options.rst + + md= [HW] RAID subsystems devices and level + See Documentation/admin-guide/md.rst. + + mdacon= [MDA] + Format: <first>,<last> + Specifies range of consoles to be captured by the MDA. + + mds= [X86,INTEL] + Control mitigation for the Micro-architectural Data + Sampling (MDS) vulnerability. + + Certain CPUs are vulnerable to an exploit against CPU + internal buffers which can forward information to a + disclosure gadget under certain conditions. + + In vulnerable processors, the speculatively + forwarded data can be used in a cache side channel + attack, to access data to which the attacker does + not have direct access. + + This parameter controls the MDS mitigation. The + options are: + + full - Enable MDS mitigation on vulnerable CPUs + full,nosmt - Enable MDS mitigation and disable + SMT on vulnerable CPUs + off - Unconditionally disable MDS mitigation + + On TAA-affected machines, mds=off can be prevented by + an active TAA mitigation as both vulnerabilities are + mitigated with the same mechanism so in order to disable + this mitigation, you need to specify tsx_async_abort=off + too. + + Not specifying this option is equivalent to + mds=full. + + For details see: Documentation/admin-guide/hw-vuln/mds.rst + + mem=nn[KMG] [HEXAGON] Set the memory size. + Must be specified, otherwise memory size will be 0. + + mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory + Amount of memory to be used in cases as follows: + + 1 for test; + 2 when the kernel is not able to see the whole system memory; + 3 memory that lies after 'mem=' boundary is excluded from + the hypervisor, then assigned to KVM guests. + 4 to limit the memory available for kdump kernel. + + [ARC,MICROBLAZE] - the limit applies only to low memory, + high memory is not affected. + + [ARM64] - only limits memory covered by the linear + mapping. The NOMAP regions are not affected. + + [X86] Work as limiting max address. Use together + with memmap= to avoid physical address space collisions. + Without memmap= PCI devices could be placed at addresses + belonging to unused RAM. + + Note that this only takes effects during boot time since + in above case 3, memory may need be hot added after boot + if system memory of hypervisor is not sufficient. + + mem=nn[KMG]@ss[KMG] + [ARM,MIPS] - override the memory layout reported by + firmware. + Define a memory region of size nn[KMG] starting at + ss[KMG]. + Multiple different regions can be specified with + multiple mem= parameters on the command line. + + mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel + memory. + + memblock=debug [KNL] Enable memblock debug messages. + + memchunk=nn[KMG] + [KNL,SH] Allow user to override the default size for + per-device physically contiguous DMA buffers. + + memhp_default_state=online/offline + [KNL] Set the initial state for the memory hotplug + onlining policy. If not specified, the default value is + set according to the + CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE kernel config + option. + See Documentation/admin-guide/mm/memory-hotplug.rst. + + memmap=exactmap [KNL,X86] Enable setting of an exact + E820 memory map, as specified by the user. + Such memmap=exactmap lines can be constructed based on + BIOS output or other requirements. See the memmap=nn@ss + option description. + + memmap=nn[KMG]@ss[KMG] + [KNL, X86, MIPS, XTENSA] Force usage of a specific region of memory. + Region of memory to be used is from ss to ss+nn. + If @ss[KMG] is omitted, it is equivalent to mem=nn[KMG], + which limits max address to nn[KMG]. + Multiple different regions can be specified, + comma delimited. + Example: + memmap=100M@2G,100M#3G,1G!1024G + + memmap=nn[KMG]#ss[KMG] + [KNL,ACPI] Mark specific memory as ACPI data. + Region of memory to be marked is from ss to ss+nn. + + memmap=nn[KMG]$ss[KMG] + [KNL,ACPI] Mark specific memory as reserved. + Region of memory to be reserved is from ss to ss+nn. + Example: Exclude memory from 0x18690000-0x1869ffff + memmap=64K$0x18690000 + or + memmap=0x10000$0x18690000 + Some bootloaders may need an escape character before '$', + like Grub2, otherwise '$' and the following number + will be eaten. + + memmap=nn[KMG]!ss[KMG] + [KNL,X86] Mark specific memory as protected. + Region of memory to be used, from ss to ss+nn. + The memory region may be marked as e820 type 12 (0xc) + and is NVDIMM or ADR memory. + + memmap=<size>%<offset>-<oldtype>+<newtype> + [KNL,ACPI] Convert memory within the specified region + from <oldtype> to <newtype>. If "-<oldtype>" is left + out, the whole region will be marked as <newtype>, + even if previously unavailable. If "+<newtype>" is left + out, matching memory will be removed. Types are + specified as e820 types, e.g., 1 = RAM, 2 = reserved, + 3 = ACPI, 12 = PRAM. + + memory_corruption_check=0/1 [X86] + Some BIOSes seem to corrupt the first 64k of + memory when doing things like suspend/resume. + Setting this option will scan the memory + looking for corruption. Enabling this will + both detect corruption and prevent the kernel + from using the memory being corrupted. + However, its intended as a diagnostic tool; if + repeatable BIOS-originated corruption always + affects the same memory, you can use memmap= + to prevent the kernel from using that memory. + + memory_corruption_check_size=size [X86] + By default it checks for corruption in the low + 64k, making this memory unavailable for normal + use. Use this parameter to scan for + corruption in more or less memory. + + memory_corruption_check_period=seconds [X86] + By default it checks for corruption every 60 + seconds. Use this parameter to check at some + other rate. 0 disables periodic checking. + + memory_hotplug.memmap_on_memory + [KNL,X86,ARM] Boolean flag to enable this feature. + Format: {on | off (default)} + When enabled, runtime hotplugged memory will + allocate its internal metadata (struct pages, + those vmemmap pages cannot be optimized even + if hugetlb_free_vmemmap is enabled) from the + hotadded memory which will allow to hotadd a + lot of memory without requiring additional + memory to do so. + This feature is disabled by default because it + has some implication on large (e.g. GB) + allocations in some configurations (e.g. small + memory blocks). + The state of the flag can be read in + /sys/module/memory_hotplug/parameters/memmap_on_memory. + Note that even when enabled, there are a few cases where + the feature is not effective. + + memtest= [KNL,X86,ARM,M68K,PPC,RISCV] Enable memtest + Format: <integer> + default : 0 <disable> + Specifies the number of memtest passes to be + performed. Each pass selects another test + pattern from a given set of patterns. Memtest + fills the memory with this pattern, validates + memory contents and reserves bad memory + regions that are detected. + + mem_encrypt= [X86-64] AMD Secure Memory Encryption (SME) control + Valid arguments: on, off + Default (depends on kernel configuration option): + on (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=y) + off (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=n) + mem_encrypt=on: Activate SME + mem_encrypt=off: Do not activate SME + + Refer to Documentation/virt/kvm/x86/amd-memory-encryption.rst + for details on when memory encryption can be activated. + + mem_sleep_default= [SUSPEND] Default system suspend mode: + s2idle - Suspend-To-Idle + shallow - Power-On Suspend or equivalent (if supported) + deep - Suspend-To-RAM or equivalent (if supported) + See Documentation/admin-guide/pm/sleep-states.rst. + + meye.*= [HW] Set MotionEye Camera parameters + See Documentation/admin-guide/media/meye.rst. + + mfgpt_irq= [IA-32] Specify the IRQ to use for the + Multi-Function General Purpose Timers on AMD Geode + platforms. + + mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when + the BIOS has incorrectly applied a workaround. TinyBIOS + version 0.98 is known to be affected, 0.99 fixes the + problem by letting the user disable the workaround. + + mga= [HW,DRM] + + min_addr=nn[KMG] [KNL,BOOT,IA-64] All physical memory below this + physical address is ignored. + + mini2440= [ARM,HW,KNL] + Format:[0..2][b][c][t] + Default: "0tb" + MINI2440 configuration specification: + 0 - The attached screen is the 3.5" TFT + 1 - The attached screen is the 7" TFT + 2 - The VGA Shield is attached (1024x768) + Leaving out the screen size parameter will not load + the TFT driver, and the framebuffer will be left + unconfigured. + b - Enable backlight. The TFT backlight pin will be + linked to the kernel VESA blanking code and a GPIO + LED. This parameter is not necessary when using the + VGA shield. + c - Enable the s3c camera interface. + t - Reserved for enabling touchscreen support. The + touchscreen support is not enabled in the mainstream + kernel as of 2.6.30, a preliminary port can be found + in the "bleeding edge" mini2440 support kernel at + https://repo.or.cz/w/linux-2.6/mini2440.git + + mitigations= + [X86,PPC,S390,ARM64] Control optional mitigations for + CPU vulnerabilities. This is a set of curated, + arch-independent options, each of which is an + aggregation of existing arch-specific options. + + off + Disable all optional CPU mitigations. This + improves system performance, but it may also + expose users to several CPU vulnerabilities. + Equivalent to: if nokaslr then kpti=0 [ARM64] + gather_data_sampling=off [X86] + kvm.nx_huge_pages=off [X86] + l1tf=off [X86] + mds=off [X86] + mmio_stale_data=off [X86] + no_entry_flush [PPC] + no_uaccess_flush [PPC] + nobp=0 [S390] + nopti [X86,PPC] + nospectre_bhb [ARM64] + nospectre_v1 [X86,PPC] + nospectre_v2 [X86,PPC,S390,ARM64] + retbleed=off [X86] + spec_store_bypass_disable=off [X86,PPC] + spectre_v2_user=off [X86] + srbds=off [X86,INTEL] + ssbd=force-off [ARM64] + tsx_async_abort=off [X86] + + Exceptions: + This does not have any effect on + kvm.nx_huge_pages when + kvm.nx_huge_pages=force. + + auto (default) + Mitigate all CPU vulnerabilities, but leave SMT + enabled, even if it's vulnerable. This is for + users who don't want to be surprised by SMT + getting disabled across kernel upgrades, or who + have other ways of avoiding SMT-based attacks. + Equivalent to: (default behavior) + + auto,nosmt + Mitigate all CPU vulnerabilities, disabling SMT + if needed. This is for users who always want to + be fully mitigated, even if it means losing SMT. + Equivalent to: l1tf=flush,nosmt [X86] + mds=full,nosmt [X86] + tsx_async_abort=full,nosmt [X86] + mmio_stale_data=full,nosmt [X86] + retbleed=auto,nosmt [X86] + + mminit_loglevel= + [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this + parameter allows control of the logging verbosity for + the additional memory initialisation checks. A value + of 0 disables mminit logging and a level of 4 will + log everything. Information is printed at KERN_DEBUG + so loglevel=8 may also need to be specified. + + mmio_stale_data= + [X86,INTEL] Control mitigation for the Processor + MMIO Stale Data vulnerabilities. + + Processor MMIO Stale Data is a class of + vulnerabilities that may expose data after an MMIO + operation. Exposed data could originate or end in + the same CPU buffers as affected by MDS and TAA. + Therefore, similar to MDS and TAA, the mitigation + is to clear the affected CPU buffers. + + This parameter controls the mitigation. The + options are: + + full - Enable mitigation on vulnerable CPUs + + full,nosmt - Enable mitigation and disable SMT on + vulnerable CPUs. + + off - Unconditionally disable mitigation + + On MDS or TAA affected machines, + mmio_stale_data=off can be prevented by an active + MDS or TAA mitigation as these vulnerabilities are + mitigated with the same mechanism so in order to + disable this mitigation, you need to specify + mds=off and tsx_async_abort=off too. + + Not specifying this option is equivalent to + mmio_stale_data=full. + + For details see: + Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst + + module.async_probe=<bool> + [KNL] When set to true, modules will use async probing + by default. To enable/disable async probing for a + specific module, use the module specific control that + is documented under <module>.async_probe. When both + module.async_probe and <module>.async_probe are + specified, <module>.async_probe takes precedence for + the specific module. + + module.sig_enforce + [KNL] When CONFIG_MODULE_SIG is set, this means that + modules without (valid) signatures will fail to load. + Note that if CONFIG_MODULE_SIG_FORCE is set, that + is always true, so this option does nothing. + + module_blacklist= [KNL] Do not load a comma-separated list of + modules. Useful for debugging problem modules. + + mousedev.tap_time= + [MOUSE] Maximum time between finger touching and + leaving touchpad surface for touch to be considered + a tap and be reported as a left button click (for + touchpads working in absolute mode only). + Format: <msecs> + mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices + reporting absolute coordinates, such as tablets + mousedev.yres= [MOUSE] Vertical screen resolution, used for devices + reporting absolute coordinates, such as tablets + + movablecore= [KNL,X86,IA-64,PPC] + Format: nn[KMGTPE] | nn% + This parameter is the complement to kernelcore=, it + specifies the amount of memory used for migratable + allocations. If both kernelcore and movablecore is + specified, then kernelcore will be at *least* the + specified value but may be more. If movablecore on its + own is specified, the administrator must be careful + that the amount of memory usable for all allocations + is not too small. + + movable_node [KNL] Boot-time switch to make hotplugable memory + NUMA nodes to be movable. This means that the memory + of such nodes will be usable only for movable + allocations which rules out almost all kernel + allocations. Use with caution! + + MTD_Partition= [MTD] + Format: <name>,<region-number>,<size>,<offset> + + MTD_Region= [MTD] Format: + <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>] + + mtdparts= [MTD] + See drivers/mtd/parsers/cmdlinepart.c + + mtdset= [ARM] + ARM/S3C2412 JIVE boot control + + See arch/arm/mach-s3c/mach-jive.c + + mtouchusb.raw_coordinates= + [HW] Make the MicroTouch USB driver use raw coordinates + ('y', default) or cooked coordinates ('n') + + mtrr_chunk_size=nn[KMG] [X86] + used for mtrr cleanup. It is largest continuous chunk + that could hold holes aka. UC entries. + + mtrr_gran_size=nn[KMG] [X86] + Used for mtrr cleanup. It is granularity of mtrr block. + Default is 1. + Large value could prevent small alignment from + using up MTRRs. + + mtrr_spare_reg_nr=n [X86] + Format: <integer> + Range: 0,7 : spare reg number + Default : 1 + Used for mtrr cleanup. It is spare mtrr entries number. + Set to 2 or more if your graphical card needs more. + + multitce=off [PPC] This parameter disables the use of the pSeries + firmware feature for updating multiple TCE entries + at a time. + + n2= [NET] SDL Inc. RISCom/N2 synchronous serial card + + netdev= [NET] Network devices parameters + Format: <irq>,<io>,<mem_start>,<mem_end>,<name> + Note that mem_start is often overloaded to mean + something different and driver-specific. + This usage is only documented in each driver source + file if at all. + + netpoll.carrier_timeout= + [NET] Specifies amount of time (in seconds) that + netpoll should wait for a carrier. By default netpoll + waits 4 seconds. + + nf_conntrack.acct= + [NETFILTER] Enable connection tracking flow accounting + 0 to disable accounting + 1 to enable accounting + Default value is 0. + + nfsaddrs= [NFS] Deprecated. Use ip= instead. + See Documentation/admin-guide/nfs/nfsroot.rst. + + nfsroot= [NFS] nfs root filesystem for disk-less boxes. + See Documentation/admin-guide/nfs/nfsroot.rst. + + nfsrootdebug [NFS] enable nfsroot debugging messages. + See Documentation/admin-guide/nfs/nfsroot.rst. + + nfs.callback_nr_threads= + [NFSv4] set the total number of threads that the + NFS client will assign to service NFSv4 callback + requests. + + nfs.callback_tcpport= + [NFS] set the TCP port on which the NFSv4 callback + channel should listen. + + nfs.cache_getent= + [NFS] sets the pathname to the program which is used + to update the NFS client cache entries. + + nfs.cache_getent_timeout= + [NFS] sets the timeout after which an attempt to + update a cache entry is deemed to have failed. + + nfs.idmap_cache_timeout= + [NFS] set the maximum lifetime for idmapper cache + entries. + + nfs.enable_ino64= + [NFS] enable 64-bit inode numbers. + If zero, the NFS client will fake up a 32-bit inode + number for the readdir() and stat() syscalls instead + of returning the full 64-bit number. + The default is to return 64-bit inode numbers. + + nfs.max_session_cb_slots= + [NFSv4.1] Sets the maximum number of session + slots the client will assign to the callback + channel. This determines the maximum number of + callbacks the client will process in parallel for + a particular server. + + nfs.max_session_slots= + [NFSv4.1] Sets the maximum number of session slots + the client will attempt to negotiate with the server. + This limits the number of simultaneous RPC requests + that the client can send to the NFSv4.1 server. + Note that there is little point in setting this + value higher than the max_tcp_slot_table_limit. + + nfs.nfs4_disable_idmapping= + [NFSv4] When set to the default of '1', this option + ensures that both the RPC level authentication + scheme and the NFS level operations agree to use + numeric uids/gids if the mount is using the + 'sec=sys' security flavour. In effect it is + disabling idmapping, which can make migration from + legacy NFSv2/v3 systems to NFSv4 easier. + Servers that do not support this mode of operation + will be autodetected by the client, and it will fall + back to using the idmapper. + To turn off this behaviour, set the value to '0'. + nfs.nfs4_unique_id= + [NFS4] Specify an additional fixed unique ident- + ification string that NFSv4 clients can insert into + their nfs_client_id4 string. This is typically a + UUID that is generated at system install time. + + nfs.send_implementation_id = + [NFSv4.1] Send client implementation identification + information in exchange_id requests. + If zero, no implementation identification information + will be sent. + The default is to send the implementation identification + information. + + nfs.recover_lost_locks = + [NFSv4] Attempt to recover locks that were lost due + to a lease timeout on the server. Please note that + doing this risks data corruption, since there are + no guarantees that the file will remain unchanged + after the locks are lost. + If you want to enable the kernel legacy behaviour of + attempting to recover these locks, then set this + parameter to '1'. + The default parameter value of '0' causes the kernel + not to attempt recovery of lost locks. + + nfs4.layoutstats_timer = + [NFSv4.2] Change the rate at which the kernel sends + layoutstats to the pNFS metadata server. + + Setting this to value to 0 causes the kernel to use + whatever value is the default set by the layout + driver. A non-zero value sets the minimum interval + in seconds between layoutstats transmissions. + + nfsd.inter_copy_offload_enable = + [NFSv4.2] When set to 1, the server will support + server-to-server copies for which this server is + the destination of the copy. + + nfsd.nfsd4_ssc_umount_timeout = + [NFSv4.2] When used as the destination of a + server-to-server copy, knfsd temporarily mounts + the source server. It caches the mount in case + it will be needed again, and discards it if not + used for the number of milliseconds specified by + this parameter. + + nfsd.nfs4_disable_idmapping= + [NFSv4] When set to the default of '1', the NFSv4 + server will return only numeric uids and gids to + clients using auth_sys, and will accept numeric uids + and gids from such clients. This is intended to ease + migration from NFSv2/v3. + + + nmi_backtrace.backtrace_idle [KNL] + Dump stacks even of idle CPUs in response to an + NMI stack-backtrace request. + + nmi_debug= [KNL,SH] Specify one or more actions to take + when a NMI is triggered. + Format: [state][,regs][,debounce][,die] + + nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels + Format: [panic,][nopanic,][num] + Valid num: 0 or 1 + 0 - turn hardlockup detector in nmi_watchdog off + 1 - turn hardlockup detector in nmi_watchdog on + When panic is specified, panic when an NMI watchdog + timeout occurs (or 'nopanic' to not panic on an NMI + watchdog, if CONFIG_BOOTPARAM_HARDLOCKUP_PANIC is set) + To disable both hard and soft lockup detectors, + please see 'nowatchdog'. + This is useful when you use a panic=... timeout and + need the box quickly up again. + + These settings can be accessed at runtime via + the nmi_watchdog and hardlockup_panic sysctls. + + no387 [BUGS=X86-32] Tells the kernel to use the 387 maths + emulation library even if a 387 maths coprocessor + is present. + + no5lvl [X86-64] Disable 5-level paging mode. Forces + kernel to use 4-level paging instead. + + nofsgsbase [X86] Disables FSGSBASE instructions. + + no_console_suspend + [HW] Never suspend the console + Disable suspending of consoles during suspend and + hibernate operations. Once disabled, debugging + messages can reach various consoles while the rest + of the system is being put to sleep (ie, while + debugging driver suspend/resume hooks). This may + not work reliably with all consoles, but is known + to work with serial and VGA consoles. + To facilitate more flexible debugging, we also add + console_suspend, a printk module parameter to control + it. Users could use console_suspend (usually + /sys/module/printk/parameters/console_suspend) to + turn on/off it dynamically. + + novmcoredd [KNL,KDUMP] + Disable device dump. Device dump allows drivers to + append dump data to vmcore so you can collect driver + specified debug info. Drivers can append the data + without any limit and this data is stored in memory, + so this may cause significant memory stress. Disabling + device dump can help save memory but the driver debug + data will be no longer available. This parameter + is only available when CONFIG_PROC_VMCORE_DEVICE_DUMP + is set. + + noaliencache [MM, NUMA, SLAB] Disables the allocation of alien + caches in the slab allocator. Saves per-node memory, + but will impact performance. + + noalign [KNL,ARM] + + noaltinstr [S390] Disables alternative instructions patching + (CPU alternatives feature). + + noapic [SMP,APIC] Tells the kernel to not make use of any + IOAPICs that may be present in the system. + + noautogroup Disable scheduler automatic task group creation. + + nocache [ARM] + + nodsp [SH] Disable hardware DSP at boot time. + + noefi Disable EFI runtime services support. + + no_entry_flush [PPC] Don't flush the L1-D cache when entering the kernel. + + noexec [IA-64] + + nosmap [PPC] + Disable SMAP (Supervisor Mode Access Prevention) + even if it is supported by processor. + + nosmep [PPC64s] + Disable SMEP (Supervisor Mode Execution Prevention) + even if it is supported by processor. + + noexec32 [X86-64] + This affects only 32-bit executables. + noexec32=on: enable non-executable mappings (default) + read doesn't imply executable mappings + noexec32=off: disable non-executable mappings + read implies executable mappings + + nofpu [MIPS,SH] Disable hardware FPU at boot time. + + nofxsr [BUGS=X86-32] Disables x86 floating point extended + register save and restore. The kernel will only save + legacy floating-point registers on task switch. + + nohugeiomap [KNL,X86,PPC,ARM64] Disable kernel huge I/O mappings. + + nohugevmalloc [KNL,X86,PPC,ARM64] Disable kernel huge vmalloc mappings. + + nosmt [KNL,S390] Disable symmetric multithreading (SMT). + Equivalent to smt=1. + + [KNL,X86] Disable symmetric multithreading (SMT). + nosmt=force: Force disable SMT, cannot be undone + via the sysfs control file. + + nospectre_v1 [X86,PPC] Disable mitigations for Spectre Variant 1 + (bounds check bypass). With this option data leaks are + possible in the system. + + nospectre_v2 [X86,PPC_E500,ARM64] Disable all mitigations for + the Spectre variant 2 (indirect branch prediction) + vulnerability. System may allow data leaks with this + option. + + nospectre_bhb [ARM64] Disable all mitigations for Spectre-BHB (branch + history injection) vulnerability. System may allow data leaks + with this option. + + nospec_store_bypass_disable + [HW] Disable all mitigations for the Speculative Store Bypass vulnerability + + no_uaccess_flush + [PPC] Don't flush the L1-D cache after accessing user data. + + noxsave [BUGS=X86] Disables x86 extended register state save + and restore using xsave. The kernel will fallback to + enabling legacy floating-point and sse state. + + noxsaveopt [X86] Disables xsaveopt used in saving x86 extended + register states. The kernel will fall back to use + xsave to save the states. By using this parameter, + performance of saving the states is degraded because + xsave doesn't support modified optimization while + xsaveopt supports it on xsaveopt enabled systems. + + noxsaves [X86] Disables xsaves and xrstors used in saving and + restoring x86 extended register state in compacted + form of xsave area. The kernel will fall back to use + xsaveopt and xrstor to save and restore the states + in standard form of xsave area. By using this + parameter, xsave area per process might occupy more + memory on xsaves enabled systems. + + nohlt [ARM,ARM64,MICROBLAZE,SH] Forces the kernel to busy wait + in do_idle() and not use the arch_cpu_idle() + implementation; requires CONFIG_GENERIC_IDLE_POLL_SETUP + to be effective. This is useful on platforms where the + sleep(SH) or wfi(ARM,ARM64) instructions do not work + correctly or when doing power measurements to evalute + the impact of the sleep instructions. This is also + useful when using JTAG debugger. + + no_file_caps Tells the kernel not to honor file capabilities. The + only way then for a file to be executed with privilege + is to be setuid root or executed by root. + + nohalt [IA-64] Tells the kernel not to use the power saving + function PAL_HALT_LIGHT when idle. This increases + power-consumption. On the positive side, it reduces + interrupt wake-up latency, which may improve performance + in certain environments such as networked servers or + real-time systems. + + no_hash_pointers + Force pointers printed to the console or buffers to be + unhashed. By default, when a pointer is printed via %p + format string, that pointer is "hashed", i.e. obscured + by hashing the pointer value. This is a security feature + that hides actual kernel addresses from unprivileged + users, but it also makes debugging the kernel more + difficult since unequal pointers can no longer be + compared. However, if this command-line option is + specified, then all normal pointers will have their true + value printed. This option should only be specified when + debugging the kernel. Please do not use on production + kernels. + + nohibernate [HIBERNATION] Disable hibernation and resume. + + nohz= [KNL] Boottime enable/disable dynamic ticks + Valid arguments: on, off + Default: on + + nohz_full= [KNL,BOOT,SMP,ISOL] + The argument is a cpu list, as described above. + In kernels built with CONFIG_NO_HZ_FULL=y, set + the specified list of CPUs whose tick will be stopped + whenever possible. The boot CPU will be forced outside + the range to maintain the timekeeping. Any CPUs + in this list will have their RCU callbacks offloaded, + just as if they had also been called out in the + rcu_nocbs= boot parameter. + + Note that this argument takes precedence over + the CONFIG_RCU_NOCB_CPU_DEFAULT_ALL option. + + noiotrap [SH] Disables trapped I/O port accesses. + + noirqdebug [X86-32] Disables the code which attempts to detect and + disable unhandled interrupt sources. + + no_timer_check [X86,APIC] Disables the code which tests for + broken timer IRQ sources. + + noisapnp [ISAPNP] Disables ISA PnP code. + + noinitrd [RAM] Tells the kernel not to load any configured + initial RAM disk. + + nointremap [X86-64, Intel-IOMMU] Do not enable interrupt + remapping. + [Deprecated - use intremap=off] + + nointroute [IA-64] + + noinvpcid [X86] Disable the INVPCID cpu feature. + + nojitter [IA-64] Disables jitter checking for ITC timers. + + no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver + + no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page + fault handling. + + no-vmw-sched-clock + [X86,PV_OPS] Disable paravirtualized VMware scheduler + clock and use the default one. + + no-steal-acc [X86,PV_OPS,ARM64,PPC/PSERIES] Disable paravirtualized + steal time accounting. steal time is computed, but + won't influence scheduler behaviour + + nolapic [X86-32,APIC] Do not enable or use the local APIC. + + nolapic_timer [X86-32,APIC] Do not use the local APIC timer. + + nomca [IA-64] Disable machine check abort handling + + nomce [X86-32] Disable Machine Check Exception + + nomfgpt [X86-32] Disable Multi-Function General Purpose + Timer usage (for AMD Geode machines). + + nonmi_ipi [X86] Disable using NMI IPIs during panic/reboot to + shutdown the other cpus. Instead use the REBOOT_VECTOR + irq. + + nomodeset Disable kernel modesetting. DRM drivers will not perform + display-mode changes or accelerated rendering. Only the + system framebuffer will be available for use if this was + set-up by the firmware or boot loader. + + Useful as fallback, or for testing and debugging. + + nomodule Disable module load + + nopat [X86] Disable PAT (page attribute table extension of + pagetables) support. + + nopcid [X86-64] Disable the PCID cpu feature. + + norandmaps Don't use address space randomization. Equivalent to + echo 0 > /proc/sys/kernel/randomize_va_space + + noreplace-smp [X86-32,SMP] Don't replace SMP instructions + with UP alternatives + + noresume [SWSUSP] Disables resume and restores original swap + space. + + no-scroll [VGA] Disables scrollback. + This is required for the Braillex ib80-piezo Braille + reader made by F.H. Papenmeier (Germany). + + nosbagart [IA-64] + + nosgx [X86-64,SGX] Disables Intel SGX kernel support. + + nosmp [SMP] Tells an SMP kernel to act as a UP kernel, + and disable the IO APIC. legacy for "maxcpus=0". + + nosoftlockup [KNL] Disable the soft-lockup detector. + + nosync [HW,M68K] Disables sync negotiation for all devices. + + nowatchdog [KNL] Disable both lockup detectors, i.e. + soft-lockup and NMI watchdog (hard-lockup). + + nowb [ARM] + + nox2apic [X86-64,APIC] Do not enable x2APIC mode. + + NOTE: this parameter will be ignored on systems with the + LEGACY_XAPIC_DISABLED bit set in the + IA32_XAPIC_DISABLE_STATUS MSR. + + nps_mtm_hs_ctr= [KNL,ARC] + This parameter sets the maximum duration, in + cycles, each HW thread of the CTOP can run + without interruptions, before HW switches it. + The actual maximum duration is 16 times this + parameter's value. + Format: integer between 1 and 255 + Default: 255 + + nptcg= [IA-64] Override max number of concurrent global TLB + purges which is reported from either PAL_VM_SUMMARY or + SAL PALO. + + nr_cpus= [SMP] Maximum number of processors that an SMP kernel + could support. nr_cpus=n : n >= 1 limits the kernel to + support 'n' processors. It could be larger than the + number of already plugged CPU during bootup, later in + runtime you can physically add extra cpu until it reaches + n. So during boot up some boot time memory for per-cpu + variables need be pre-allocated for later physical cpu + hot plugging. + + nr_uarts= [SERIAL] maximum number of UARTs to be registered. + + numa=off [KNL, ARM64, PPC, RISCV, SPARC, X86] Disable NUMA, Only + set up a single NUMA node spanning all memory. + + numa_balancing= [KNL,ARM64,PPC,RISCV,S390,X86] Enable or disable automatic + NUMA balancing. + Allowed values are enable and disable + + numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. + 'node', 'default' can be specified + This can be set from sysctl after boot. + See Documentation/admin-guide/sysctl/vm.rst for details. + + ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. + See Documentation/core-api/debugging-via-ohci1394.rst for more + info. + + olpc_ec_timeout= [OLPC] ms delay when issuing EC commands + Rather than timing out after 20 ms if an EC + command is not properly ACKed, override the length + of the timeout. We have interrupts disabled while + waiting for the ACK, so if this is set too high + interrupts *may* be lost! + + omap_mux= [OMAP] Override bootloader pin multiplexing. + Format: <mux_mode0.mode_name=value>... + For example, to override I2C bus2: + omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100 + + onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration + + Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock] + + boundary - index of last SLC block on Flex-OneNAND. + The remaining blocks are configured as MLC blocks. + lock - Configure if Flex-OneNAND boundary should be locked. + Once locked, the boundary cannot be changed. + 1 indicates lock status, 0 indicates unlock status. + + oops=panic Always panic on oopses. Default is to just kill the + process, but there is a small probability of + deadlocking the machine. + This will also cause panics on machine check exceptions. + Useful together with panic=30 to trigger a reboot. + + page_alloc.shuffle= + [KNL] Boolean flag to control whether the page allocator + should randomize its free lists. The randomization may + be automatically enabled if the kernel detects it is + running on a platform with a direct-mapped memory-side + cache, and this parameter can be used to + override/disable that behavior. The state of the flag + can be read from sysfs at: + /sys/module/page_alloc/parameters/shuffle. + + page_owner= [KNL] Boot-time page_owner enabling option. + Storage of the information about who allocated + each page is disabled in default. With this switch, + we can turn it on. + on: enable the feature + + page_poison= [KNL] Boot-time parameter changing the state of + poisoning on the buddy allocator, available with + CONFIG_PAGE_POISONING=y. + off: turn off poisoning (default) + on: turn on poisoning + + page_reporting.page_reporting_order= + [KNL] Minimal page reporting order + Format: <integer> + Adjust the minimal page reporting order. The page + reporting is disabled when it exceeds (MAX_ORDER-1). + + panic= [KNL] Kernel behaviour on panic: delay <timeout> + timeout > 0: seconds before rebooting + timeout = 0: wait forever + timeout < 0: reboot immediately + Format: <timeout> + + panic_print= Bitmask for printing system info when panic happens. + User can chose combination of the following bits: + bit 0: print all tasks info + bit 1: print system memory info + bit 2: print timer info + bit 3: print locks info if CONFIG_LOCKDEP is on + bit 4: print ftrace buffer + bit 5: print all printk messages in buffer + bit 6: print all CPUs backtrace (if available in the arch) + *Be aware* that this option may print a _lot_ of lines, + so there are risks of losing older messages in the log. + Use this option carefully, maybe worth to setup a + bigger log buffer with "log_buf_len" along with this. + + panic_on_taint= Bitmask for conditionally calling panic() in add_taint() + Format: <hex>[,nousertaint] + Hexadecimal bitmask representing the set of TAINT flags + that will cause the kernel to panic when add_taint() is + called with any of the flags in this set. + The optional switch "nousertaint" can be utilized to + prevent userspace forced crashes by writing to sysctl + /proc/sys/kernel/tainted any flagset matching with the + bitmask set on panic_on_taint. + See Documentation/admin-guide/tainted-kernels.rst for + extra details on the taint flags that users can pick + to compose the bitmask to assign to panic_on_taint. + + panic_on_warn panic() instead of WARN(). Useful to cause kdump + on a WARN(). + + parkbd.port= [HW] Parallel port number the keyboard adapter is + connected to, default is 0. + Format: <parport#> + parkbd.mode= [HW] Parallel port keyboard adapter mode of operation, + 0 for XT, 1 for AT (default is AT). + Format: <mode> + + parport= [HW,PPT] Specify parallel ports. 0 disables. + Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] } + Use 'auto' to force the driver to use any + IRQ/DMA settings detected (the default is to + ignore detected IRQ/DMA settings because of + possible conflicts). You can specify the base + address, IRQ, and DMA settings; IRQ and DMA + should be numbers, or 'auto' (for using detected + settings on that particular port), or 'nofifo' + (to avoid using a FIFO even if it is detected). + Parallel ports are assigned in the order they + are specified on the command line, starting + with parport0. + + parport_init_mode= [HW,PPT] + Configure VIA parallel port to operate in + a specific mode. This is necessary on Pegasos + computer where firmware has no options for setting + up parallel port mode and sets it to spp. + Currently this function knows 686a and 8231 chips. + Format: [spp|ps2|epp|ecp|ecpepp] + + pata_legacy.all= [HW,LIBATA] + Format: <int> + Set to non-zero to probe primary and secondary ISA + port ranges on PCI systems where no PCI PATA device + has been found at either range. Disabled by default. + + pata_legacy.autospeed= [HW,LIBATA] + Format: <int> + Set to non-zero if a chip is present that snoops speed + changes. Disabled by default. + + pata_legacy.ht6560a= [HW,LIBATA] + Format: <int> + Set to 1, 2, or 3 for HT 6560A on the primary channel, + the secondary channel, or both channels respectively. + Disabled by default. + + pata_legacy.ht6560b= [HW,LIBATA] + Format: <int> + Set to 1, 2, or 3 for HT 6560B on the primary channel, + the secondary channel, or both channels respectively. + Disabled by default. + + pata_legacy.iordy_mask= [HW,LIBATA] + Format: <int> + IORDY enable mask. Set individual bits to allow IORDY + for the respective channel. Bit 0 is for the first + legacy channel handled by this driver, bit 1 is for + the second channel, and so on. The sequence will often + correspond to the primary legacy channel, the secondary + legacy channel, and so on, but the handling of a PCI + bus and the use of other driver options may interfere + with the sequence. By default IORDY is allowed across + all channels. + + pata_legacy.opti82c46x= [HW,LIBATA] + Format: <int> + Set to 1, 2, or 3 for Opti 82c611A on the primary + channel, the secondary channel, or both channels + respectively. Disabled by default. + + pata_legacy.opti82c611a= [HW,LIBATA] + Format: <int> + Set to 1, 2, or 3 for Opti 82c465MV on the primary + channel, the secondary channel, or both channels + respectively. Disabled by default. + + pata_legacy.pio_mask= [HW,LIBATA] + Format: <int> + PIO mode mask for autospeed devices. Set individual + bits to allow the use of the respective PIO modes. + Bit 0 is for mode 0, bit 1 is for mode 1, and so on. + All modes allowed by default. + + pata_legacy.probe_all= [HW,LIBATA] + Format: <int> + Set to non-zero to probe tertiary and further ISA + port ranges on PCI systems. Disabled by default. + + pata_legacy.probe_mask= [HW,LIBATA] + Format: <int> + Probe mask for legacy ISA PATA ports. Depending on + platform configuration and the use of other driver + options up to 6 legacy ports are supported: 0x1f0, + 0x170, 0x1e8, 0x168, 0x1e0, 0x160, however probing + of individual ports can be disabled by setting the + corresponding bits in the mask to 1. Bit 0 is for + the first port in the list above (0x1f0), and so on. + By default all supported ports are probed. + + pata_legacy.qdi= [HW,LIBATA] + Format: <int> + Set to non-zero to probe QDI controllers. By default + set to 1 if CONFIG_PATA_QDI_MODULE, 0 otherwise. + + pata_legacy.winbond= [HW,LIBATA] + Format: <int> + Set to non-zero to probe Winbond controllers. Use + the standard I/O port (0x130) if 1, otherwise the + value given is the I/O port to use (typically 0x1b0). + By default set to 1 if CONFIG_PATA_WINBOND_VLB_MODULE, + 0 otherwise. + + pata_platform.pio_mask= [HW,LIBATA] + Format: <int> + Supported PIO mode mask. Set individual bits to allow + the use of the respective PIO modes. Bit 0 is for + mode 0, bit 1 is for mode 1, and so on. Mode 0 only + allowed by default. + + pause_on_oops= + Halt all CPUs after the first oops has been printed for + the specified number of seconds. This is to be used if + your oopses keep scrolling off the screen. + + pcbit= [HW,ISDN] + + pcd. [PARIDE] + See header of drivers/block/paride/pcd.c. + See also Documentation/admin-guide/blockdev/paride.rst. + + pci=option[,option...] [PCI] various PCI subsystem options. + + Some options herein operate on a specific device + or a set of devices (<pci_dev>). These are + specified in one of the following formats: + + [<domain>:]<bus>:<dev>.<func>[/<dev>.<func>]* + pci:<vendor>:<device>[:<subvendor>:<subdevice>] + + Note: the first format specifies a PCI + bus/device/function address which may change + if new hardware is inserted, if motherboard + firmware changes, or due to changes caused + by other kernel parameters. If the + domain is left unspecified, it is + taken to be zero. Optionally, a path + to a device through multiple device/function + addresses can be specified after the base + address (this is more robust against + renumbering issues). The second format + selects devices using IDs from the + configuration space which may match multiple + devices in the system. + + earlydump dump PCI config space before the kernel + changes anything + off [X86] don't probe for the PCI bus + bios [X86-32] force use of PCI BIOS, don't access + the hardware directly. Use this if your machine + has a non-standard PCI host bridge. + nobios [X86-32] disallow use of PCI BIOS, only direct + hardware access methods are allowed. Use this + if you experience crashes upon bootup and you + suspect they are caused by the BIOS. + conf1 [X86] Force use of PCI Configuration Access + Mechanism 1 (config address in IO port 0xCF8, + data in IO port 0xCFC, both 32-bit). + conf2 [X86] Force use of PCI Configuration Access + Mechanism 2 (IO port 0xCF8 is an 8-bit port for + the function, IO port 0xCFA, also 8-bit, sets + bus number. The config space is then accessed + through ports 0xC000-0xCFFF). + See http://wiki.osdev.org/PCI for more info + on the configuration access mechanisms. + noaer [PCIE] If the PCIEAER kernel config parameter is + enabled, this kernel boot option can be used to + disable the use of PCIE advanced error reporting. + nodomains [PCI] Disable support for multiple PCI + root domains (aka PCI segments, in ACPI-speak). + nommconf [X86] Disable use of MMCONFIG for PCI + Configuration + check_enable_amd_mmconf [X86] check for and enable + properly configured MMIO access to PCI + config space on AMD family 10h CPU + nomsi [MSI] If the PCI_MSI kernel config parameter is + enabled, this kernel boot option can be used to + disable the use of MSI interrupts system-wide. + noioapicquirk [APIC] Disable all boot interrupt quirks. + Safety option to keep boot IRQs enabled. This + should never be necessary. + ioapicreroute [APIC] Enable rerouting of boot IRQs to the + primary IO-APIC for bridges that cannot disable + boot IRQs. This fixes a source of spurious IRQs + when the system masks IRQs. + noioapicreroute [APIC] Disable workaround that uses the + boot IRQ equivalent of an IRQ that connects to + a chipset where boot IRQs cannot be disabled. + The opposite of ioapicreroute. + biosirq [X86-32] Use PCI BIOS calls to get the interrupt + routing table. These calls are known to be buggy + on several machines and they hang the machine + when used, but on other computers it's the only + way to get the interrupt routing table. Try + this option if the kernel is unable to allocate + IRQs or discover secondary PCI buses on your + motherboard. + rom [X86] Assign address space to expansion ROMs. + Use with caution as certain devices share + address decoders between ROMs and other + resources. + norom [X86] Do not assign address space to + expansion ROMs that do not already have + BIOS assigned address ranges. + nobar [X86] Do not assign address space to the + BARs that weren't assigned by the BIOS. + irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be + assigned automatically to PCI devices. You can + make the kernel exclude IRQs of your ISA cards + this way. + pirqaddr=0xAAAAA [X86] Specify the physical address + of the PIRQ table (normally generated + by the BIOS) if it is outside the + F0000h-100000h range. + lastbus=N [X86] Scan all buses thru bus #N. Can be + useful if the kernel is unable to find your + secondary buses and you want to tell it + explicitly which ones they are. + assign-busses [X86] Always assign all PCI bus + numbers ourselves, overriding + whatever the firmware may have done. + usepirqmask [X86] Honor the possible IRQ mask stored + in the BIOS $PIR table. This is needed on + some systems with broken BIOSes, notably + some HP Pavilion N5400 and Omnibook XE3 + notebooks. This will have no effect if ACPI + IRQ routing is enabled. + noacpi [X86] Do not use ACPI for IRQ routing + or for PCI scanning. + use_crs [X86] Use PCI host bridge window information + from ACPI. On BIOSes from 2008 or later, this + is enabled by default. If you need to use this, + please report a bug. + nocrs [X86] Ignore PCI host bridge windows from ACPI. + If you need to use this, please report a bug. + use_e820 [X86] Use E820 reservations to exclude parts of + PCI host bridge windows. This is a workaround + for BIOS defects in host bridge _CRS methods. + If you need to use this, please report a bug to + <linux-pci@vger.kernel.org>. + no_e820 [X86] Ignore E820 reservations for PCI host + bridge windows. This is the default on modern + hardware. If you need to use this, please report + a bug to <linux-pci@vger.kernel.org>. + routeirq Do IRQ routing for all PCI devices. + This is normally done in pci_enable_device(), + so this option is a temporary workaround + for broken drivers that don't call it. + skip_isa_align [X86] do not align io start addr, so can + handle more pci cards + noearly [X86] Don't do any early type 1 scanning. + This might help on some broken boards which + machine check when some devices' config space + is read. But various workarounds are disabled + and some IOMMU drivers will not work. + bfsort Sort PCI devices into breadth-first order. + This sorting is done to get a device + order compatible with older (<= 2.4) kernels. + nobfsort Don't sort PCI devices into breadth-first order. + pcie_bus_tune_off Disable PCIe MPS (Max Payload Size) + tuning and use the BIOS-configured MPS defaults. + pcie_bus_safe Set every device's MPS to the largest value + supported by all devices below the root complex. + pcie_bus_perf Set device MPS to the largest allowable MPS + based on its parent bus. Also set MRRS (Max + Read Request Size) to the largest supported + value (no larger than the MPS that the device + or bus can support) for best performance. + pcie_bus_peer2peer Set every device's MPS to 128B, which + every device is guaranteed to support. This + configuration allows peer-to-peer DMA between + any pair of devices, possibly at the cost of + reduced performance. This also guarantees + that hot-added devices will work. + cbiosize=nn[KMG] The fixed amount of bus space which is + reserved for the CardBus bridge's IO window. + The default value is 256 bytes. + cbmemsize=nn[KMG] The fixed amount of bus space which is + reserved for the CardBus bridge's memory + window. The default value is 64 megabytes. + resource_alignment= + Format: + [<order of align>@]<pci_dev>[; ...] + Specifies alignment and device to reassign + aligned memory resources. How to + specify the device is described above. + If <order of align> is not specified, + PAGE_SIZE is used as alignment. + A PCI-PCI bridge can be specified if resource + windows need to be expanded. + To specify the alignment for several + instances of a device, the PCI vendor, + device, subvendor, and subdevice may be + specified, e.g., 12@pci:8086:9c22:103c:198f + for 4096-byte alignment. + ecrc= Enable/disable PCIe ECRC (transaction layer + end-to-end CRC checking). + bios: Use BIOS/firmware settings. This is the + the default. + off: Turn ECRC off + on: Turn ECRC on. + hpiosize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's IO window. + Default size is 256 bytes. + hpmmiosize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's MMIO window. + Default size is 2 megabytes. + hpmmioprefsize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's MMIO_PREF window. + Default size is 2 megabytes. + hpmemsize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's MMIO and + MMIO_PREF window. + Default size is 2 megabytes. + hpbussize=nn The minimum amount of additional bus numbers + reserved for buses below a hotplug bridge. + Default is 1. + realloc= Enable/disable reallocating PCI bridge resources + if allocations done by BIOS are too small to + accommodate resources required by all child + devices. + off: Turn realloc off + on: Turn realloc on + realloc same as realloc=on + noari do not use PCIe ARI. + noats [PCIE, Intel-IOMMU, AMD-IOMMU] + do not use PCIe ATS (and IOMMU device IOTLB). + pcie_scan_all Scan all possible PCIe devices. Otherwise we + only look for one device below a PCIe downstream + port. + big_root_window Try to add a big 64bit memory window to the PCIe + root complex on AMD CPUs. Some GFX hardware + can resize a BAR to allow access to all VRAM. + Adding the window is slightly risky (it may + conflict with unreported devices), so this + taints the kernel. + disable_acs_redir=<pci_dev>[; ...] + Specify one or more PCI devices (in the format + specified above) separated by semicolons. + Each device specified will have the PCI ACS + redirect capabilities forced off which will + allow P2P traffic between devices through + bridges without forcing it upstream. Note: + this removes isolation between devices and + may put more devices in an IOMMU group. + force_floating [S390] Force usage of floating interrupts. + nomio [S390] Do not use MIO instructions. + norid [S390] ignore the RID field and force use of + one PCI domain per PCI function + + pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power + Management. + off Disable ASPM. + force Enable ASPM even on devices that claim not to support it. + WARNING: Forcing ASPM on may cause system lockups. + + pcie_ports= [PCIE] PCIe port services handling: + native Use native PCIe services (PME, AER, DPC, PCIe hotplug) + even if the platform doesn't give the OS permission to + use them. This may cause conflicts if the platform + also tries to use these services. + dpc-native Use native PCIe service for DPC only. May + cause conflicts if firmware uses AER or DPC. + compat Disable native PCIe services (PME, AER, DPC, PCIe + hotplug). + + pcie_port_pm= [PCIE] PCIe port power management handling: + off Disable power management of all PCIe ports + force Forcibly enable power management of all PCIe ports + + pcie_pme= [PCIE,PM] Native PCIe PME signaling options: + nomsi Do not use MSI for native PCIe PME signaling (this makes + all PCIe root ports use INTx for all services). + + pcmv= [HW,PCMCIA] BadgePAD 4 + + pd_ignore_unused + [PM] + Keep all power-domains already enabled by bootloader on, + even if no driver has claimed them. This is useful + for debug and development, but should not be + needed on a platform with proper driver support. + + pd. [PARIDE] + See Documentation/admin-guide/blockdev/paride.rst. + + pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at + boot time. + Format: { 0 | 1 } + See arch/parisc/kernel/pdc_chassis.c + + percpu_alloc= Select which percpu first chunk allocator to use. + Currently supported values are "embed" and "page". + Archs may support subset or none of the selections. + See comments in mm/percpu.c for details on each + allocator. This parameter is primarily for debugging + and performance comparison. + + pf. [PARIDE] + See Documentation/admin-guide/blockdev/paride.rst. + + pg. [PARIDE] + See Documentation/admin-guide/blockdev/paride.rst. + + pirq= [SMP,APIC] Manual mp-table setup + See Documentation/x86/i386/IO-APIC.rst. + + plip= [PPT,NET] Parallel port network link + Format: { parport<nr> | timid | 0 } + See also Documentation/admin-guide/parport.rst. + + pmtmr= [X86] Manual setup of pmtmr I/O Port. + Override pmtimer IOPort with a hex value. + e.g. pmtmr=0x508 + + pmu_override= [PPC] Override the PMU. + This option takes over the PMU facility, so it is no + longer usable by perf. Setting this option starts the + PMU counters by setting MMCR0 to 0 (the FC bit is + cleared). If a number is given, then MMCR1 is set to + that number, otherwise (e.g., 'pmu_override=on'), MMCR1 + remains 0. + + pm_debug_messages [SUSPEND,KNL] + Enable suspend/resume debug messages during boot up. + + pnp.debug=1 [PNP] + Enable PNP debug messages (depends on the + CONFIG_PNP_DEBUG_MESSAGES option). Change at run-time + via /sys/module/pnp/parameters/debug. We always show + current resource usage; turning this on also shows + possible settings and some assignment information. + + pnpacpi= [ACPI] + { off } + + pnpbios= [ISAPNP] + { on | off | curr | res | no-curr | no-res } + + pnp_reserve_irq= + [ISAPNP] Exclude IRQs for the autoconfiguration + + pnp_reserve_dma= + [ISAPNP] Exclude DMAs for the autoconfiguration + + pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration + Ranges are in pairs (I/O port base and size). + + pnp_reserve_mem= + [ISAPNP] Exclude memory regions for the + autoconfiguration. + Ranges are in pairs (memory base and size). + + ports= [IP_VS_FTP] IPVS ftp helper module + Default is 21. + Up to 8 (IP_VS_APP_MAX_PORTS) ports + may be specified. + Format: <port>,<port>.... + + powersave=off [PPC] This option disables power saving features. + It specifically disables cpuidle and sets the + platform machine description specific power_save + function to NULL. On Idle the CPU just reduces + execution priority. + + ppc_strict_facility_enable + [PPC] This option catches any kernel floating point, + Altivec, VSX and SPE outside of regions specifically + allowed (eg kernel_enable_fpu()/kernel_disable_fpu()). + There is some performance impact when enabling this. + + ppc_tm= [PPC] + Format: {"off"} + Disable Hardware Transactional Memory + + preempt= [KNL] + Select preemption mode if you have CONFIG_PREEMPT_DYNAMIC + none - Limited to cond_resched() calls + voluntary - Limited to cond_resched() and might_sleep() calls + full - Any section that isn't explicitly preempt disabled + can be preempted anytime. + + print-fatal-signals= + [KNL] debug: print fatal signals + + If enabled, warn about various signal handling + related application anomalies: too many signals, + too many POSIX.1 timers, fatal signals causing a + coredump - etc. + + If you hit the warning due to signal overflow, + you might want to try "ulimit -i unlimited". + + default: off. + + printk.always_kmsg_dump= + Trigger kmsg_dump for cases other than kernel oops or + panics + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + default: disabled + + printk.console_no_auto_verbose= + Disable console loglevel raise on oops, panic + or lockdep-detected issues (only if lock debug is on). + With an exception to setups with low baudrate on + serial console, keeping this 0 is a good choice + in order to provide more debug information. + Format: <bool> + default: 0 (auto_verbose is enabled) + + printk.devkmsg={on,off,ratelimit} + Control writing to /dev/kmsg. + on - unlimited logging to /dev/kmsg from userspace + off - logging to /dev/kmsg disabled + ratelimit - ratelimit the logging + Default: ratelimit + + printk.time= Show timing data prefixed to each printk message line + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + + processor.max_cstate= [HW,ACPI] + Limit processor to maximum C-state + max_cstate=9 overrides any DMI blacklist limit. + + processor.nocst [HW,ACPI] + Ignore the _CST method to determine C-states, + instead using the legacy FADT method + + profile= [KNL] Enable kernel profiling via /proc/profile + Format: [<profiletype>,]<number> + Param: <profiletype>: "schedule", "sleep", or "kvm" + [defaults to kernel profiling] + Param: "schedule" - profile schedule points. + Param: "sleep" - profile D-state sleeping (millisecs). + Requires CONFIG_SCHEDSTATS + Param: "kvm" - profile VM exits. + Param: <number> - step/bucket size as a power of 2 for + statistical time based profiling. + + prompt_ramdisk= [RAM] [Deprecated] + + prot_virt= [S390] enable hosting protected virtual machines + isolated from the hypervisor (if hardware supports + that). + Format: <bool> + + psi= [KNL] Enable or disable pressure stall information + tracking. + Format: <bool> + + psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to + probe for; one of (bare|imps|exps|lifebook|any). + psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports + per second. + psmouse.resetafter= [HW,MOUSE] + Try to reset the device after so many bad packets + (0 = never). + psmouse.resolution= + [HW,MOUSE] Set desired mouse resolution, in dpi. + psmouse.smartscroll= + [HW,MOUSE] Controls Logitech smartscroll autorepeat. + 0 = disabled, 1 = enabled (default). + + pstore.backend= Specify the name of the pstore backend to use + + pt. [PARIDE] + See Documentation/admin-guide/blockdev/paride.rst. + + pti= [X86-64] Control Page Table Isolation of user and + kernel address spaces. Disabling this feature + removes hardening, but improves performance of + system calls and interrupts. + + on - unconditionally enable + off - unconditionally disable + auto - kernel detects whether your CPU model is + vulnerable to issues that PTI mitigates + + Not specifying this option is equivalent to pti=auto. + + nopti [X86-64] + Equivalent to pti=off + + pty.legacy_count= + [KNL] Number of legacy pty's. Overwrites compiled-in + default number. + + quiet [KNL] Disable most log messages + + r128= [HW,DRM] + + raid= [HW,RAID] + See Documentation/admin-guide/md.rst. + + ramdisk_size= [RAM] Sizes of RAM disks in kilobytes + See Documentation/admin-guide/blockdev/ramdisk.rst. + + ramdisk_start= [RAM] RAM disk image start address + + random.trust_cpu={on,off} + [KNL] Enable or disable trusting the use of the + CPU's random number generator (if available) to + fully seed the kernel's CRNG. Default is controlled + by CONFIG_RANDOM_TRUST_CPU. + + random.trust_bootloader={on,off} + [KNL] Enable or disable trusting the use of a + seed passed by the bootloader (if available) to + fully seed the kernel's CRNG. Default is controlled + by CONFIG_RANDOM_TRUST_BOOTLOADER. + + randomize_kstack_offset= + [KNL] Enable or disable kernel stack offset + randomization, which provides roughly 5 bits of + entropy, frustrating memory corruption attacks + that depend on stack address determinism or + cross-syscall address exposures. This is only + available on architectures that have defined + CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET. + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + Default is CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT. + + ras=option[,option,...] [KNL] RAS-specific options + + cec_disable [X86] + Disable the Correctable Errors Collector, + see CONFIG_RAS_CEC help text. + + rcu_nocbs[=cpu-list] + [KNL] The optional argument is a cpu list, + as described above. + + In kernels built with CONFIG_RCU_NOCB_CPU=y, + enable the no-callback CPU mode, which prevents + such CPUs' callbacks from being invoked in + softirq context. Invocation of such CPUs' RCU + callbacks will instead be offloaded to "rcuox/N" + kthreads created for that purpose, where "x" is + "p" for RCU-preempt, "s" for RCU-sched, and "g" + for the kthreads that mediate grace periods; and + "N" is the CPU number. This reduces OS jitter on + the offloaded CPUs, which can be useful for HPC + and real-time workloads. It can also improve + energy efficiency for asymmetric multiprocessors. + + If a cpulist is passed as an argument, the specified + list of CPUs is set to no-callback mode from boot. + + Otherwise, if the '=' sign and the cpulist + arguments are omitted, no CPU will be set to + no-callback mode from boot but the mode may be + toggled at runtime via cpusets. + + Note that this argument takes precedence over + the CONFIG_RCU_NOCB_CPU_DEFAULT_ALL option. + + rcu_nocb_poll [KNL] + Rather than requiring that offloaded CPUs + (specified by rcu_nocbs= above) explicitly + awaken the corresponding "rcuoN" kthreads, + make these kthreads poll for callbacks. + This improves the real-time response for the + offloaded CPUs by relieving them of the need to + wake up the corresponding kthread, but degrades + energy efficiency by requiring that the kthreads + periodically wake up to do the polling. + + rcutree.blimit= [KNL] + Set maximum number of finished RCU callbacks to + process in one batch. + + rcutree.dump_tree= [KNL] + Dump the structure of the rcu_node combining tree + out at early boot. This is used for diagnostic + purposes, to verify correct tree setup. + + rcutree.gp_cleanup_delay= [KNL] + Set the number of jiffies to delay each step of + RCU grace-period cleanup. + + rcutree.gp_init_delay= [KNL] + Set the number of jiffies to delay each step of + RCU grace-period initialization. + + rcutree.gp_preinit_delay= [KNL] + Set the number of jiffies to delay each step of + RCU grace-period pre-initialization, that is, + the propagation of recent CPU-hotplug changes up + the rcu_node combining tree. + + rcutree.use_softirq= [KNL] + If set to zero, move all RCU_SOFTIRQ processing to + per-CPU rcuc kthreads. Defaults to a non-zero + value, meaning that RCU_SOFTIRQ is used by default. + Specify rcutree.use_softirq=0 to use rcuc kthreads. + + But note that CONFIG_PREEMPT_RT=y kernels disable + this kernel boot parameter, forcibly setting it + to zero. + + rcutree.rcu_fanout_exact= [KNL] + Disable autobalancing of the rcu_node combining + tree. This is used by rcutorture, and might + possibly be useful for architectures having high + cache-to-cache transfer latencies. + + rcutree.rcu_fanout_leaf= [KNL] + Change the number of CPUs assigned to each + leaf rcu_node structure. Useful for very + large systems, which will choose the value 64, + and for NUMA systems with large remote-access + latencies, which will choose a value aligned + with the appropriate hardware boundaries. + + rcutree.rcu_min_cached_objs= [KNL] + Minimum number of objects which are cached and + maintained per one CPU. Object size is equal + to PAGE_SIZE. The cache allows to reduce the + pressure to page allocator, also it makes the + whole algorithm to behave better in low memory + condition. + + rcutree.rcu_delay_page_cache_fill_msec= [KNL] + Set the page-cache refill delay (in milliseconds) + in response to low-memory conditions. The range + of permitted values is in the range 0:100000. + + rcutree.jiffies_till_first_fqs= [KNL] + Set delay from grace-period initialization to + first attempt to force quiescent states. + Units are jiffies, minimum value is zero, + and maximum value is HZ. + + rcutree.jiffies_till_next_fqs= [KNL] + Set delay between subsequent attempts to force + quiescent states. Units are jiffies, minimum + value is one, and maximum value is HZ. + + rcutree.jiffies_till_sched_qs= [KNL] + Set required age in jiffies for a + given grace period before RCU starts + soliciting quiescent-state help from + rcu_note_context_switch() and cond_resched(). + If not specified, the kernel will calculate + a value based on the most recent settings + of rcutree.jiffies_till_first_fqs + and rcutree.jiffies_till_next_fqs. + This calculated value may be viewed in + rcutree.jiffies_to_sched_qs. Any attempt to set + rcutree.jiffies_to_sched_qs will be cheerfully + overwritten. + + rcutree.kthread_prio= [KNL,BOOT] + Set the SCHED_FIFO priority of the RCU per-CPU + kthreads (rcuc/N). This value is also used for + the priority of the RCU boost threads (rcub/N) + and for the RCU grace-period kthreads (rcu_bh, + rcu_preempt, and rcu_sched). If RCU_BOOST is + set, valid values are 1-99 and the default is 1 + (the least-favored priority). Otherwise, when + RCU_BOOST is not set, valid values are 0-99 and + the default is zero (non-realtime operation). + When RCU_NOCB_CPU is set, also adjust the + priority of NOCB callback kthreads. + + rcutree.rcu_divisor= [KNL] + Set the shift-right count to use to compute + the callback-invocation batch limit bl from + the number of callbacks queued on this CPU. + The result will be bounded below by the value of + the rcutree.blimit kernel parameter. Every bl + callbacks, the softirq handler will exit in + order to allow the CPU to do other work. + + Please note that this callback-invocation batch + limit applies only to non-offloaded callback + invocation. Offloaded callbacks are instead + invoked in the context of an rcuoc kthread, which + scheduler will preempt as it does any other task. + + rcutree.nocb_nobypass_lim_per_jiffy= [KNL] + On callback-offloaded (rcu_nocbs) CPUs, + RCU reduces the lock contention that would + otherwise be caused by callback floods through + use of the ->nocb_bypass list. However, in the + common non-flooded case, RCU queues directly to + the main ->cblist in order to avoid the extra + overhead of the ->nocb_bypass list and its lock. + But if there are too many callbacks queued during + a single jiffy, RCU pre-queues the callbacks into + the ->nocb_bypass queue. The definition of "too + many" is supplied by this kernel boot parameter. + + rcutree.rcu_nocb_gp_stride= [KNL] + Set the number of NOCB callback kthreads in + each group, which defaults to the square root + of the number of CPUs. Larger numbers reduce + the wakeup overhead on the global grace-period + kthread, but increases that same overhead on + each group's NOCB grace-period kthread. + + rcutree.qhimark= [KNL] + Set threshold of queued RCU callbacks beyond which + batch limiting is disabled. + + rcutree.qlowmark= [KNL] + Set threshold of queued RCU callbacks below which + batch limiting is re-enabled. + + rcutree.qovld= [KNL] + Set threshold of queued RCU callbacks beyond which + RCU's force-quiescent-state scan will aggressively + enlist help from cond_resched() and sched IPIs to + help CPUs more quickly reach quiescent states. + Set to less than zero to make this be set based + on rcutree.qhimark at boot time and to zero to + disable more aggressive help enlistment. + + rcutree.rcu_kick_kthreads= [KNL] + Cause the grace-period kthread to get an extra + wake_up() if it sleeps three times longer than + it should at force-quiescent-state time. + This wake_up() will be accompanied by a + WARN_ONCE() splat and an ftrace_dump(). + + rcutree.rcu_unlock_delay= [KNL] + In CONFIG_RCU_STRICT_GRACE_PERIOD=y kernels, + this specifies an rcu_read_unlock()-time delay + in microseconds. This defaults to zero. + Larger delays increase the probability of + catching RCU pointer leaks, that is, buggy use + of RCU-protected pointers after the relevant + rcu_read_unlock() has completed. + + rcutree.sysrq_rcu= [KNL] + Commandeer a sysrq key to dump out Tree RCU's + rcu_node tree with an eye towards determining + why a new grace period has not yet started. + + rcuscale.gp_async= [KNL] + Measure performance of asynchronous + grace-period primitives such as call_rcu(). + + rcuscale.gp_async_max= [KNL] + Specify the maximum number of outstanding + callbacks per writer thread. When a writer + thread exceeds this limit, it invokes the + corresponding flavor of rcu_barrier() to allow + previously posted callbacks to drain. + + rcuscale.gp_exp= [KNL] + Measure performance of expedited synchronous + grace-period primitives. + + rcuscale.holdoff= [KNL] + Set test-start holdoff period. The purpose of + this parameter is to delay the start of the + test until boot completes in order to avoid + interference. + + rcuscale.kfree_rcu_test= [KNL] + Set to measure performance of kfree_rcu() flooding. + + rcuscale.kfree_rcu_test_double= [KNL] + Test the double-argument variant of kfree_rcu(). + If this parameter has the same value as + rcuscale.kfree_rcu_test_single, both the single- + and double-argument variants are tested. + + rcuscale.kfree_rcu_test_single= [KNL] + Test the single-argument variant of kfree_rcu(). + If this parameter has the same value as + rcuscale.kfree_rcu_test_double, both the single- + and double-argument variants are tested. + + rcuscale.kfree_nthreads= [KNL] + The number of threads running loops of kfree_rcu(). + + rcuscale.kfree_alloc_num= [KNL] + Number of allocations and frees done in an iteration. + + rcuscale.kfree_loops= [KNL] + Number of loops doing rcuscale.kfree_alloc_num number + of allocations and frees. + + rcuscale.nreaders= [KNL] + Set number of RCU readers. The value -1 selects + N, where N is the number of CPUs. A value + "n" less than -1 selects N-n+1, where N is again + the number of CPUs. For example, -2 selects N + (the number of CPUs), -3 selects N+1, and so on. + A value of "n" less than or equal to -N selects + a single reader. + + rcuscale.nwriters= [KNL] + Set number of RCU writers. The values operate + the same as for rcuscale.nreaders. + N, where N is the number of CPUs + + rcuscale.perf_type= [KNL] + Specify the RCU implementation to test. + + rcuscale.shutdown= [KNL] + Shut the system down after performance tests + complete. This is useful for hands-off automated + testing. + + rcuscale.verbose= [KNL] + Enable additional printk() statements. + + rcuscale.writer_holdoff= [KNL] + Write-side holdoff between grace periods, + in microseconds. The default of zero says + no holdoff. + + rcutorture.fqs_duration= [KNL] + Set duration of force_quiescent_state bursts + in microseconds. + + rcutorture.fqs_holdoff= [KNL] + Set holdoff time within force_quiescent_state bursts + in microseconds. + + rcutorture.fqs_stutter= [KNL] + Set wait time between force_quiescent_state bursts + in seconds. + + rcutorture.fwd_progress= [KNL] + Specifies the number of kthreads to be used + for RCU grace-period forward-progress testing + for the types of RCU supporting this notion. + Defaults to 1 kthread, values less than zero or + greater than the number of CPUs cause the number + of CPUs to be used. + + rcutorture.fwd_progress_div= [KNL] + Specify the fraction of a CPU-stall-warning + period to do tight-loop forward-progress testing. + + rcutorture.fwd_progress_holdoff= [KNL] + Number of seconds to wait between successive + forward-progress tests. + + rcutorture.fwd_progress_need_resched= [KNL] + Enclose cond_resched() calls within checks for + need_resched() during tight-loop forward-progress + testing. + + rcutorture.gp_cond= [KNL] + Use conditional/asynchronous update-side + primitives, if available. + + rcutorture.gp_exp= [KNL] + Use expedited update-side primitives, if available. + + rcutorture.gp_normal= [KNL] + Use normal (non-expedited) asynchronous + update-side primitives, if available. + + rcutorture.gp_sync= [KNL] + Use normal (non-expedited) synchronous + update-side primitives, if available. If all + of rcutorture.gp_cond=, rcutorture.gp_exp=, + rcutorture.gp_normal=, and rcutorture.gp_sync= + are zero, rcutorture acts as if is interpreted + they are all non-zero. + + rcutorture.irqreader= [KNL] + Run RCU readers from irq handlers, or, more + accurately, from a timer handler. Not all RCU + flavors take kindly to this sort of thing. + + rcutorture.leakpointer= [KNL] + Leak an RCU-protected pointer out of the reader. + This can of course result in splats, and is + intended to test the ability of things like + CONFIG_RCU_STRICT_GRACE_PERIOD=y to detect + such leaks. + + rcutorture.n_barrier_cbs= [KNL] + Set callbacks/threads for rcu_barrier() testing. + + rcutorture.nfakewriters= [KNL] + Set number of concurrent RCU writers. These just + stress RCU, they don't participate in the actual + test, hence the "fake". + + rcutorture.nocbs_nthreads= [KNL] + Set number of RCU callback-offload togglers. + Zero (the default) disables toggling. + + rcutorture.nocbs_toggle= [KNL] + Set the delay in milliseconds between successive + callback-offload toggling attempts. + + rcutorture.nreaders= [KNL] + Set number of RCU readers. The value -1 selects + N-1, where N is the number of CPUs. A value + "n" less than -1 selects N-n-2, where N is again + the number of CPUs. For example, -2 selects N + (the number of CPUs), -3 selects N+1, and so on. + + rcutorture.object_debug= [KNL] + Enable debug-object double-call_rcu() testing. + + rcutorture.onoff_holdoff= [KNL] + Set time (s) after boot for CPU-hotplug testing. + + rcutorture.onoff_interval= [KNL] + Set time (jiffies) between CPU-hotplug operations, + or zero to disable CPU-hotplug testing. + + rcutorture.read_exit= [KNL] + Set the number of read-then-exit kthreads used + to test the interaction of RCU updaters and + task-exit processing. + + rcutorture.read_exit_burst= [KNL] + The number of times in a given read-then-exit + episode that a set of read-then-exit kthreads + is spawned. + + rcutorture.read_exit_delay= [KNL] + The delay, in seconds, between successive + read-then-exit testing episodes. + + rcutorture.shuffle_interval= [KNL] + Set task-shuffle interval (s). Shuffling tasks + allows some CPUs to go into dyntick-idle mode + during the rcutorture test. + + rcutorture.shutdown_secs= [KNL] + Set time (s) after boot system shutdown. This + is useful for hands-off automated testing. + + rcutorture.stall_cpu= [KNL] + Duration of CPU stall (s) to test RCU CPU stall + warnings, zero to disable. + + rcutorture.stall_cpu_block= [KNL] + Sleep while stalling if set. This will result + in warnings from preemptible RCU in addition + to any other stall-related activity. + + rcutorture.stall_cpu_holdoff= [KNL] + Time to wait (s) after boot before inducing stall. + + rcutorture.stall_cpu_irqsoff= [KNL] + Disable interrupts while stalling if set. + + rcutorture.stall_gp_kthread= [KNL] + Duration (s) of forced sleep within RCU + grace-period kthread to test RCU CPU stall + warnings, zero to disable. If both stall_cpu + and stall_gp_kthread are specified, the + kthread is starved first, then the CPU. + + rcutorture.stat_interval= [KNL] + Time (s) between statistics printk()s. + + rcutorture.stutter= [KNL] + Time (s) to stutter testing, for example, specifying + five seconds causes the test to run for five seconds, + wait for five seconds, and so on. This tests RCU's + ability to transition abruptly to and from idle. + + rcutorture.test_boost= [KNL] + Test RCU priority boosting? 0=no, 1=maybe, 2=yes. + "Maybe" means test if the RCU implementation + under test support RCU priority boosting. + + rcutorture.test_boost_duration= [KNL] + Duration (s) of each individual boost test. + + rcutorture.test_boost_interval= [KNL] + Interval (s) between each boost test. + + rcutorture.test_no_idle_hz= [KNL] + Test RCU's dyntick-idle handling. See also the + rcutorture.shuffle_interval parameter. + + rcutorture.torture_type= [KNL] + Specify the RCU implementation to test. + + rcutorture.verbose= [KNL] + Enable additional printk() statements. + + rcupdate.rcu_cpu_stall_ftrace_dump= [KNL] + Dump ftrace buffer after reporting RCU CPU + stall warning. + + rcupdate.rcu_cpu_stall_suppress= [KNL] + Suppress RCU CPU stall warning messages. + + rcupdate.rcu_cpu_stall_suppress_at_boot= [KNL] + Suppress RCU CPU stall warning messages and + rcutorture writer stall warnings that occur + during early boot, that is, during the time + before the init task is spawned. + + rcupdate.rcu_cpu_stall_timeout= [KNL] + Set timeout for RCU CPU stall warning messages. + The value is in seconds and the maximum allowed + value is 300 seconds. + + rcupdate.rcu_exp_cpu_stall_timeout= [KNL] + Set timeout for expedited RCU CPU stall warning + messages. The value is in milliseconds + and the maximum allowed value is 21000 + milliseconds. Please note that this value is + adjusted to an arch timer tick resolution. + Setting this to zero causes the value from + rcupdate.rcu_cpu_stall_timeout to be used (after + conversion from seconds to milliseconds). + + rcupdate.rcu_expedited= [KNL] + Use expedited grace-period primitives, for + example, synchronize_rcu_expedited() instead + of synchronize_rcu(). This reduces latency, + but can increase CPU utilization, degrade + real-time latency, and degrade energy efficiency. + No effect on CONFIG_TINY_RCU kernels. + + rcupdate.rcu_normal= [KNL] + Use only normal grace-period primitives, + for example, synchronize_rcu() instead of + synchronize_rcu_expedited(). This improves + real-time latency, CPU utilization, and + energy efficiency, but can expose users to + increased grace-period latency. This parameter + overrides rcupdate.rcu_expedited. No effect on + CONFIG_TINY_RCU kernels. + + rcupdate.rcu_normal_after_boot= [KNL] + Once boot has completed (that is, after + rcu_end_inkernel_boot() has been invoked), use + only normal grace-period primitives. No effect + on CONFIG_TINY_RCU kernels. + + But note that CONFIG_PREEMPT_RT=y kernels enables + this kernel boot parameter, forcibly setting + it to the value one, that is, converting any + post-boot attempt at an expedited RCU grace + period to instead use normal non-expedited + grace-period processing. + + rcupdate.rcu_task_collapse_lim= [KNL] + Set the maximum number of callbacks present + at the beginning of a grace period that allows + the RCU Tasks flavors to collapse back to using + a single callback queue. This switching only + occurs when rcupdate.rcu_task_enqueue_lim is + set to the default value of -1. + + rcupdate.rcu_task_contend_lim= [KNL] + Set the minimum number of callback-queuing-time + lock-contention events per jiffy required to + cause the RCU Tasks flavors to switch to per-CPU + callback queuing. This switching only occurs + when rcupdate.rcu_task_enqueue_lim is set to + the default value of -1. + + rcupdate.rcu_task_enqueue_lim= [KNL] + Set the number of callback queues to use for the + RCU Tasks family of RCU flavors. The default + of -1 allows this to be automatically (and + dynamically) adjusted. This parameter is intended + for use in testing. + + rcupdate.rcu_task_ipi_delay= [KNL] + Set time in jiffies during which RCU tasks will + avoid sending IPIs, starting with the beginning + of a given grace period. Setting a large + number avoids disturbing real-time workloads, + but lengthens grace periods. + + rcupdate.rcu_task_stall_info= [KNL] + Set initial timeout in jiffies for RCU task stall + informational messages, which give some indication + of the problem for those not patient enough to + wait for ten minutes. Informational messages are + only printed prior to the stall-warning message + for a given grace period. Disable with a value + less than or equal to zero. Defaults to ten + seconds. A change in value does not take effect + until the beginning of the next grace period. + + rcupdate.rcu_task_stall_info_mult= [KNL] + Multiplier for time interval between successive + RCU task stall informational messages for a given + RCU tasks grace period. This value is clamped + to one through ten, inclusive. It defaults to + the value three, so that the first informational + message is printed 10 seconds into the grace + period, the second at 40 seconds, the third at + 160 seconds, and then the stall warning at 600 + seconds would prevent a fourth at 640 seconds. + + rcupdate.rcu_task_stall_timeout= [KNL] + Set timeout in jiffies for RCU task stall + warning messages. Disable with a value less + than or equal to zero. Defaults to ten minutes. + A change in value does not take effect until + the beginning of the next grace period. + + rcupdate.rcu_self_test= [KNL] + Run the RCU early boot self tests + + rdinit= [KNL] + Format: <full_path> + Run specified binary instead of /init from the ramdisk, + used for early userspace startup. See initrd. + + rdrand= [X86] + force - Override the decision by the kernel to hide the + advertisement of RDRAND support (this affects + certain AMD processors because of buggy BIOS + support, specifically around the suspend/resume + path). + + rdt= [HW,X86,RDT] + Turn on/off individual RDT features. List is: + cmt, mbmtotal, mbmlocal, l3cat, l3cdp, l2cat, l2cdp, + mba. + E.g. to turn on cmt and turn off mba use: + rdt=cmt,!mba + + reboot= [KNL] + Format (x86 or x86_64): + [w[arm] | c[old] | h[ard] | s[oft] | g[pio]] | d[efault] \ + [[,]s[mp]#### \ + [[,]b[ios] | a[cpi] | k[bd] | t[riple] | e[fi] | p[ci]] \ + [[,]f[orce] + Where reboot_mode is one of warm (soft) or cold (hard) or gpio + (prefix with 'panic_' to set mode for panic + reboot only), + reboot_type is one of bios, acpi, kbd, triple, efi, or pci, + reboot_force is either force or not specified, + reboot_cpu is s[mp]#### with #### being the processor + to be used for rebooting. + + refscale.holdoff= [KNL] + Set test-start holdoff period. The purpose of + this parameter is to delay the start of the + test until boot completes in order to avoid + interference. + + refscale.loops= [KNL] + Set the number of loops over the synchronization + primitive under test. Increasing this number + reduces noise due to loop start/end overhead, + but the default has already reduced the per-pass + noise to a handful of picoseconds on ca. 2020 + x86 laptops. + + refscale.nreaders= [KNL] + Set number of readers. The default value of -1 + selects N, where N is roughly 75% of the number + of CPUs. A value of zero is an interesting choice. + + refscale.nruns= [KNL] + Set number of runs, each of which is dumped onto + the console log. + + refscale.readdelay= [KNL] + Set the read-side critical-section duration, + measured in microseconds. + + refscale.scale_type= [KNL] + Specify the read-protection implementation to test. + + refscale.shutdown= [KNL] + Shut down the system at the end of the performance + test. This defaults to 1 (shut it down) when + refscale is built into the kernel and to 0 (leave + it running) when refscale is built as a module. + + refscale.verbose= [KNL] + Enable additional printk() statements. + + refscale.verbose_batched= [KNL] + Batch the additional printk() statements. If zero + (the default) or negative, print everything. Otherwise, + print every Nth verbose statement, where N is the value + specified. + + relax_domain_level= + [KNL, SMP] Set scheduler's default relax_domain_level. + See Documentation/admin-guide/cgroup-v1/cpusets.rst. + + reserve= [KNL,BUGS] Force kernel to ignore I/O ports or memory + Format: <base1>,<size1>[,<base2>,<size2>,...] + Reserve I/O ports or memory so the kernel won't use + them. If <base> is less than 0x10000, the region + is assumed to be I/O ports; otherwise it is memory. + + reservetop= [X86-32] + Format: nn[KMG] + Reserves a hole at the top of the kernel virtual + address space. + + reset_devices [KNL] Force drivers to reset the underlying device + during initialization. + + resume= [SWSUSP] + Specify the partition device for software suspend + Format: + {/dev/<dev> | PARTUUID=<uuid> | <int>:<int> | <hex>} + + resume_offset= [SWSUSP] + Specify the offset from the beginning of the partition + given by "resume=" at which the swap header is located, + in <PAGE_SIZE> units (needed only for swap files). + See Documentation/power/swsusp-and-swap-files.rst + + resumedelay= [HIBERNATION] Delay (in seconds) to pause before attempting to + read the resume files + + resumewait [HIBERNATION] Wait (indefinitely) for resume device to show up. + Useful for devices that are detected asynchronously + (e.g. USB and MMC devices). + + retain_initrd [RAM] Keep initrd memory after extraction + + retbleed= [X86] Control mitigation of RETBleed (Arbitrary + Speculative Code Execution with Return Instructions) + vulnerability. + + AMD-based UNRET and IBPB mitigations alone do not stop + sibling threads from influencing the predictions of other + sibling threads. For that reason, STIBP is used on pro- + cessors that support it, and mitigate SMT on processors + that don't. + + off - no mitigation + auto - automatically select a migitation + auto,nosmt - automatically select a mitigation, + disabling SMT if necessary for + the full mitigation (only on Zen1 + and older without STIBP). + ibpb - On AMD, mitigate short speculation + windows on basic block boundaries too. + Safe, highest perf impact. It also + enables STIBP if present. Not suitable + on Intel. + ibpb,nosmt - Like "ibpb" above but will disable SMT + when STIBP is not available. This is + the alternative for systems which do not + have STIBP. + unret - Force enable untrained return thunks, + only effective on AMD f15h-f17h based + systems. + unret,nosmt - Like unret, but will disable SMT when STIBP + is not available. This is the alternative for + systems which do not have STIBP. + + Selecting 'auto' will choose a mitigation method at run + time according to the CPU. + + Not specifying this option is equivalent to retbleed=auto. + + rfkill.default_state= + 0 "airplane mode". All wifi, bluetooth, wimax, gps, fm, + etc. communication is blocked by default. + 1 Unblocked. + + rfkill.master_switch_mode= + 0 The "airplane mode" button does nothing. + 1 The "airplane mode" button toggles between everything + blocked and the previous configuration. + 2 The "airplane mode" button toggles between everything + blocked and everything unblocked. + + rhash_entries= [KNL,NET] + Set number of hash buckets for route cache + + ring3mwait=disable + [KNL] Disable ring 3 MONITOR/MWAIT feature on supported + CPUs. + + ro [KNL] Mount root device read-only on boot + + rodata= [KNL] + on Mark read-only kernel memory as read-only (default). + off Leave read-only kernel memory writable for debugging. + full Mark read-only kernel memory and aliases as read-only + [arm64] + + rockchip.usb_uart + Enable the uart passthrough on the designated usb port + on Rockchip SoCs. When active, the signals of the + debug-uart get routed to the D+ and D- pins of the usb + port and the regular usb controller gets disabled. + + root= [KNL] Root filesystem + See name_to_dev_t comment in init/do_mounts.c. + + rootdelay= [KNL] Delay (in seconds) to pause before attempting to + mount the root filesystem + + rootflags= [KNL] Set root filesystem mount option string + + rootfstype= [KNL] Set root filesystem type + + rootwait [KNL] Wait (indefinitely) for root device to show up. + Useful for devices that are detected asynchronously + (e.g. USB and MMC devices). + + rproc_mem=nn[KMG][@address] + [KNL,ARM,CMA] Remoteproc physical memory block. + Memory area to be used by remote processor image, + managed by CMA. + + rw [KNL] Mount root device read-write on boot + + S [KNL] Run init in single mode + + s390_iommu= [HW,S390] + Set s390 IOTLB flushing mode + strict + With strict flushing every unmap operation will result in + an IOTLB flush. Default is lazy flushing before reuse, + which is faster. + + s390_iommu_aperture= [KNL,S390] + Specifies the size of the per device DMA address space + accessible through the DMA and IOMMU APIs as a decimal + factor of the size of main memory. + The default is 1 meaning that one can concurrently use + as many DMA addresses as physical memory is installed, + if supported by hardware, and thus map all of memory + once. With a value of 2 one can map all of memory twice + and so on. As a special case a factor of 0 imposes no + restrictions other than those given by hardware at the + cost of significant additional memory use for tables. + + sa1100ir [NET] + See drivers/net/irda/sa1100_ir.c. + + sched_verbose [KNL] Enables verbose scheduler debug messages. + + schedstats= [KNL,X86] Enable or disable scheduled statistics. + Allowed values are enable and disable. This feature + incurs a small amount of overhead in the scheduler + but is useful for debugging and performance tuning. + + sched_thermal_decay_shift= + [KNL, SMP] Set a decay shift for scheduler thermal + pressure signal. Thermal pressure signal follows the + default decay period of other scheduler pelt + signals(usually 32 ms but configurable). Setting + sched_thermal_decay_shift will left shift the decay + period for the thermal pressure signal by the shift + value. + i.e. with the default pelt decay period of 32 ms + sched_thermal_decay_shift thermal pressure decay pr + 1 64 ms + 2 128 ms + and so on. + Format: integer between 0 and 10 + Default is 0. + + scftorture.holdoff= [KNL] + Number of seconds to hold off before starting + test. Defaults to zero for module insertion and + to 10 seconds for built-in smp_call_function() + tests. + + scftorture.longwait= [KNL] + Request ridiculously long waits randomly selected + up to the chosen limit in seconds. Zero (the + default) disables this feature. Please note + that requesting even small non-zero numbers of + seconds can result in RCU CPU stall warnings, + softlockup complaints, and so on. + + scftorture.nthreads= [KNL] + Number of kthreads to spawn to invoke the + smp_call_function() family of functions. + The default of -1 specifies a number of kthreads + equal to the number of CPUs. + + scftorture.onoff_holdoff= [KNL] + Number seconds to wait after the start of the + test before initiating CPU-hotplug operations. + + scftorture.onoff_interval= [KNL] + Number seconds to wait between successive + CPU-hotplug operations. Specifying zero (which + is the default) disables CPU-hotplug operations. + + scftorture.shutdown_secs= [KNL] + The number of seconds following the start of the + test after which to shut down the system. The + default of zero avoids shutting down the system. + Non-zero values are useful for automated tests. + + scftorture.stat_interval= [KNL] + The number of seconds between outputting the + current test statistics to the console. A value + of zero disables statistics output. + + scftorture.stutter_cpus= [KNL] + The number of jiffies to wait between each change + to the set of CPUs under test. + + scftorture.use_cpus_read_lock= [KNL] + Use use_cpus_read_lock() instead of the default + preempt_disable() to disable CPU hotplug + while invoking one of the smp_call_function*() + functions. + + scftorture.verbose= [KNL] + Enable additional printk() statements. + + scftorture.weight_single= [KNL] + The probability weighting to use for the + smp_call_function_single() function with a zero + "wait" parameter. A value of -1 selects the + default if all other weights are -1. However, + if at least one weight has some other value, a + value of -1 will instead select a weight of zero. + + scftorture.weight_single_wait= [KNL] + The probability weighting to use for the + smp_call_function_single() function with a + non-zero "wait" parameter. See weight_single. + + scftorture.weight_many= [KNL] + The probability weighting to use for the + smp_call_function_many() function with a zero + "wait" parameter. See weight_single. + Note well that setting a high probability for + this weighting can place serious IPI load + on the system. + + scftorture.weight_many_wait= [KNL] + The probability weighting to use for the + smp_call_function_many() function with a + non-zero "wait" parameter. See weight_single + and weight_many. + + scftorture.weight_all= [KNL] + The probability weighting to use for the + smp_call_function_all() function with a zero + "wait" parameter. See weight_single and + weight_many. + + scftorture.weight_all_wait= [KNL] + The probability weighting to use for the + smp_call_function_all() function with a + non-zero "wait" parameter. See weight_single + and weight_many. + + skew_tick= [KNL] Offset the periodic timer tick per cpu to mitigate + xtime_lock contention on larger systems, and/or RCU lock + contention on all systems with CONFIG_MAXSMP set. + Format: { "0" | "1" } + 0 -- disable. (may be 1 via CONFIG_CMDLINE="skew_tick=1" + 1 -- enable. + Note: increases power consumption, thus should only be + enabled if running jitter sensitive (HPC/RT) workloads. + + security= [SECURITY] Choose a legacy "major" security module to + enable at boot. This has been deprecated by the + "lsm=" parameter. + + selinux= [SELINUX] Disable or enable SELinux at boot time. + Format: { "0" | "1" } + See security/selinux/Kconfig help text. + 0 -- disable. + 1 -- enable. + Default value is 1. + + apparmor= [APPARMOR] Disable or enable AppArmor at boot time + Format: { "0" | "1" } + See security/apparmor/Kconfig help text + 0 -- disable. + 1 -- enable. + Default value is set via kernel config option. + + serialnumber [BUGS=X86-32] + + sev=option[,option...] [X86-64] See Documentation/x86/x86_64/boot-options.rst + + shapers= [NET] + Maximal number of shapers. + + simeth= [IA-64] + simscsi= + + slram= [HW,MTD] + + slab_merge [MM] + Enable merging of slabs with similar size when the + kernel is built without CONFIG_SLAB_MERGE_DEFAULT. + + slab_nomerge [MM] + Disable merging of slabs with similar size. May be + necessary if there is some reason to distinguish + allocs to different slabs, especially in hardened + environments where the risk of heap overflows and + layout control by attackers can usually be + frustrated by disabling merging. This will reduce + most of the exposure of a heap attack to a single + cache (risks via metadata attacks are mostly + unchanged). Debug options disable merging on their + own. + For more information see Documentation/mm/slub.rst. + + slab_max_order= [MM, SLAB] + Determines the maximum allowed order for slabs. + A high setting may cause OOMs due to memory + fragmentation. Defaults to 1 for systems with + more than 32MB of RAM, 0 otherwise. + + slub_debug[=options[,slabs][;[options[,slabs]]...] [MM, SLUB] + Enabling slub_debug allows one to determine the + culprit if slab objects become corrupted. Enabling + slub_debug can create guard zones around objects and + may poison objects when not in use. Also tracks the + last alloc / free. For more information see + Documentation/mm/slub.rst. + + slub_max_order= [MM, SLUB] + Determines the maximum allowed order for slabs. + A high setting may cause OOMs due to memory + fragmentation. For more information see + Documentation/mm/slub.rst. + + slub_min_objects= [MM, SLUB] + The minimum number of objects per slab. SLUB will + increase the slab order up to slub_max_order to + generate a sufficiently large slab able to contain + the number of objects indicated. The higher the number + of objects the smaller the overhead of tracking slabs + and the less frequently locks need to be acquired. + For more information see Documentation/mm/slub.rst. + + slub_min_order= [MM, SLUB] + Determines the minimum page order for slabs. Must be + lower than slub_max_order. + For more information see Documentation/mm/slub.rst. + + slub_merge [MM, SLUB] + Same with slab_merge. + + slub_nomerge [MM, SLUB] + Same with slab_nomerge. This is supported for legacy. + See slab_nomerge for more information. + + smart2= [HW] + Format: <io1>[,<io2>[,...,<io8>]] + + smp.csd_lock_timeout= [KNL] + Specify the period of time in milliseconds + that smp_call_function() and friends will wait + for a CPU to release the CSD lock. This is + useful when diagnosing bugs involving CPUs + disabling interrupts for extended periods + of time. Defaults to 5,000 milliseconds, and + setting a value of zero disables this feature. + This feature may be more efficiently disabled + using the csdlock_debug- kernel parameter. + + smp.panic_on_ipistall= [KNL] + If a csd_lock_timeout extends for more than + the specified number of milliseconds, panic the + system. By default, let CSD-lock acquisition + take as long as they take. Specifying 300,000 + for this value provides a 5-minute timeout. + + smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices + smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port + smsc-ircc2.ircc_sir= [HW] SIR base I/O port + smsc-ircc2.ircc_fir= [HW] FIR base I/O port + smsc-ircc2.ircc_irq= [HW] IRQ line + smsc-ircc2.ircc_dma= [HW] DMA channel + smsc-ircc2.ircc_transceiver= [HW] Transceiver type: + 0: Toshiba Satellite 1800 (GP data pin select) + 1: Fast pin select (default) + 2: ATC IRMode + + smt= [KNL,S390] Set the maximum number of threads (logical + CPUs) to use per physical CPU on systems capable of + symmetric multithreading (SMT). Will be capped to the + actual hardware limit. + Format: <integer> + Default: -1 (no limit) + + softlockup_panic= + [KNL] Should the soft-lockup detector generate panics. + Format: 0 | 1 + + A value of 1 instructs the soft-lockup detector + to panic the machine when a soft-lockup occurs. It is + also controlled by the kernel.softlockup_panic sysctl + and CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC, which is the + respective build-time switch to that functionality. + + softlockup_all_cpu_backtrace= + [KNL] Should the soft-lockup detector generate + backtraces on all cpus. + Format: 0 | 1 + + sonypi.*= [HW] Sony Programmable I/O Control Device driver + See Documentation/admin-guide/laptops/sonypi.rst + + spectre_v2= [X86] Control mitigation of Spectre variant 2 + (indirect branch speculation) vulnerability. + The default operation protects the kernel from + user space attacks. + + on - unconditionally enable, implies + spectre_v2_user=on + off - unconditionally disable, implies + spectre_v2_user=off + auto - kernel detects whether your CPU model is + vulnerable + + Selecting 'on' will, and 'auto' may, choose a + mitigation method at run time according to the + CPU, the available microcode, the setting of the + CONFIG_RETPOLINE configuration option, and the + compiler with which the kernel was built. + + Selecting 'on' will also enable the mitigation + against user space to user space task attacks. + + Selecting 'off' will disable both the kernel and + the user space protections. + + Specific mitigations can also be selected manually: + + retpoline - replace indirect branches + retpoline,generic - Retpolines + retpoline,lfence - LFENCE; indirect branch + retpoline,amd - alias for retpoline,lfence + eibrs - enhanced IBRS + eibrs,retpoline - enhanced IBRS + Retpolines + eibrs,lfence - enhanced IBRS + LFENCE + ibrs - use IBRS to protect kernel + + Not specifying this option is equivalent to + spectre_v2=auto. + + spectre_v2_user= + [X86] Control mitigation of Spectre variant 2 + (indirect branch speculation) vulnerability between + user space tasks + + on - Unconditionally enable mitigations. Is + enforced by spectre_v2=on + + off - Unconditionally disable mitigations. Is + enforced by spectre_v2=off + + prctl - Indirect branch speculation is enabled, + but mitigation can be enabled via prctl + per thread. The mitigation control state + is inherited on fork. + + prctl,ibpb + - Like "prctl" above, but only STIBP is + controlled per thread. IBPB is issued + always when switching between different user + space processes. + + seccomp + - Same as "prctl" above, but all seccomp + threads will enable the mitigation unless + they explicitly opt out. + + seccomp,ibpb + - Like "seccomp" above, but only STIBP is + controlled per thread. IBPB is issued + always when switching between different + user space processes. + + auto - Kernel selects the mitigation depending on + the available CPU features and vulnerability. + + Default mitigation: "prctl" + + Not specifying this option is equivalent to + spectre_v2_user=auto. + + spec_rstack_overflow= + [X86] Control RAS overflow mitigation on AMD Zen CPUs + + off - Disable mitigation + microcode - Enable microcode mitigation only + safe-ret - Enable sw-only safe RET mitigation (default) + ibpb - Enable mitigation by issuing IBPB on + kernel entry + ibpb-vmexit - Issue IBPB only on VMEXIT + (cloud-specific mitigation) + + spec_store_bypass_disable= + [HW] Control Speculative Store Bypass (SSB) Disable mitigation + (Speculative Store Bypass vulnerability) + + Certain CPUs are vulnerable to an exploit against a + a common industry wide performance optimization known + as "Speculative Store Bypass" in which recent stores + to the same memory location may not be observed by + later loads during speculative execution. The idea + is that such stores are unlikely and that they can + be detected prior to instruction retirement at the + end of a particular speculation execution window. + + In vulnerable processors, the speculatively forwarded + store can be used in a cache side channel attack, for + example to read memory to which the attacker does not + directly have access (e.g. inside sandboxed code). + + This parameter controls whether the Speculative Store + Bypass optimization is used. + + On x86 the options are: + + on - Unconditionally disable Speculative Store Bypass + off - Unconditionally enable Speculative Store Bypass + auto - Kernel detects whether the CPU model contains an + implementation of Speculative Store Bypass and + picks the most appropriate mitigation. If the + CPU is not vulnerable, "off" is selected. If the + CPU is vulnerable the default mitigation is + architecture and Kconfig dependent. See below. + prctl - Control Speculative Store Bypass per thread + via prctl. Speculative Store Bypass is enabled + for a process by default. The state of the control + is inherited on fork. + seccomp - Same as "prctl" above, but all seccomp threads + will disable SSB unless they explicitly opt out. + + Default mitigations: + X86: "prctl" + + On powerpc the options are: + + on,auto - On Power8 and Power9 insert a store-forwarding + barrier on kernel entry and exit. On Power7 + perform a software flush on kernel entry and + exit. + off - No action. + + Not specifying this option is equivalent to + spec_store_bypass_disable=auto. + + spia_io_base= [HW,MTD] + spia_fio_base= + spia_pedr= + spia_peddr= + + split_lock_detect= + [X86] Enable split lock detection or bus lock detection + + When enabled (and if hardware support is present), atomic + instructions that access data across cache line + boundaries will result in an alignment check exception + for split lock detection or a debug exception for + bus lock detection. + + off - not enabled + + warn - the kernel will emit rate-limited warnings + about applications triggering the #AC + exception or the #DB exception. This mode is + the default on CPUs that support split lock + detection or bus lock detection. Default + behavior is by #AC if both features are + enabled in hardware. + + fatal - the kernel will send SIGBUS to applications + that trigger the #AC exception or the #DB + exception. Default behavior is by #AC if + both features are enabled in hardware. + + ratelimit:N - + Set system wide rate limit to N bus locks + per second for bus lock detection. + 0 < N <= 1000. + + N/A for split lock detection. + + + If an #AC exception is hit in the kernel or in + firmware (i.e. not while executing in user mode) + the kernel will oops in either "warn" or "fatal" + mode. + + #DB exception for bus lock is triggered only when + CPL > 0. + + srbds= [X86,INTEL] + Control the Special Register Buffer Data Sampling + (SRBDS) mitigation. + + Certain CPUs are vulnerable to an MDS-like + exploit which can leak bits from the random + number generator. + + By default, this issue is mitigated by + microcode. However, the microcode fix can cause + the RDRAND and RDSEED instructions to become + much slower. Among other effects, this will + result in reduced throughput from /dev/urandom. + + The microcode mitigation can be disabled with + the following option: + + off: Disable mitigation and remove + performance impact to RDRAND and RDSEED + + srcutree.big_cpu_lim [KNL] + Specifies the number of CPUs constituting a + large system, such that srcu_struct structures + should immediately allocate an srcu_node array. + This kernel-boot parameter defaults to 128, + but takes effect only when the low-order four + bits of srcutree.convert_to_big is equal to 3 + (decide at boot). + + srcutree.convert_to_big [KNL] + Specifies under what conditions an SRCU tree + srcu_struct structure will be converted to big + form, that is, with an rcu_node tree: + + 0: Never. + 1: At init_srcu_struct() time. + 2: When rcutorture decides to. + 3: Decide at boot time (default). + 0x1X: Above plus if high contention. + + Either way, the srcu_node tree will be sized based + on the actual runtime number of CPUs (nr_cpu_ids) + instead of the compile-time CONFIG_NR_CPUS. + + srcutree.counter_wrap_check [KNL] + Specifies how frequently to check for + grace-period sequence counter wrap for the + srcu_data structure's ->srcu_gp_seq_needed field. + The greater the number of bits set in this kernel + parameter, the less frequently counter wrap will + be checked for. Note that the bottom two bits + are ignored. + + srcutree.exp_holdoff [KNL] + Specifies how many nanoseconds must elapse + since the end of the last SRCU grace period for + a given srcu_struct until the next normal SRCU + grace period will be considered for automatic + expediting. Set to zero to disable automatic + expediting. + + srcutree.srcu_max_nodelay [KNL] + Specifies the number of no-delay instances + per jiffy for which the SRCU grace period + worker thread will be rescheduled with zero + delay. Beyond this limit, worker thread will + be rescheduled with a sleep delay of one jiffy. + + srcutree.srcu_max_nodelay_phase [KNL] + Specifies the per-grace-period phase, number of + non-sleeping polls of readers. Beyond this limit, + grace period worker thread will be rescheduled + with a sleep delay of one jiffy, between each + rescan of the readers, for a grace period phase. + + srcutree.srcu_retry_check_delay [KNL] + Specifies number of microseconds of non-sleeping + delay between each non-sleeping poll of readers. + + srcutree.small_contention_lim [KNL] + Specifies the number of update-side contention + events per jiffy will be tolerated before + initiating a conversion of an srcu_struct + structure to big form. Note that the value of + srcutree.convert_to_big must have the 0x10 bit + set for contention-based conversions to occur. + + ssbd= [ARM64,HW] + Speculative Store Bypass Disable control + + On CPUs that are vulnerable to the Speculative + Store Bypass vulnerability and offer a + firmware based mitigation, this parameter + indicates how the mitigation should be used: + + force-on: Unconditionally enable mitigation for + for both kernel and userspace + force-off: Unconditionally disable mitigation for + for both kernel and userspace + kernel: Always enable mitigation in the + kernel, and offer a prctl interface + to allow userspace to register its + interest in being mitigated too. + + stack_guard_gap= [MM] + override the default stack gap protection. The value + is in page units and it defines how many pages prior + to (for stacks growing down) resp. after (for stacks + growing up) the main stack are reserved for no other + mapping. Default value is 256 pages. + + stack_depot_disable= [KNL] + Setting this to true through kernel command line will + disable the stack depot thereby saving the static memory + consumed by the stack hash table. By default this is set + to false. + + stacktrace [FTRACE] + Enabled the stack tracer on boot up. + + stacktrace_filter=[function-list] + [FTRACE] Limit the functions that the stack tracer + will trace at boot up. function-list is a comma-separated + list of functions. This list can be changed at run + time by the stack_trace_filter file in the debugfs + tracing directory. Note, this enables stack tracing + and the stacktrace above is not needed. + + sti= [PARISC,HW] + Format: <num> + Set the STI (builtin display/keyboard on the HP-PARISC + machines) console (graphic card) which should be used + as the initial boot-console. + See also comment in drivers/video/console/sticore.c. + + sti_font= [HW] + See comment in drivers/video/console/sticore.c. + + stifb= [HW] + Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]] + + strict_sas_size= + [X86] + Format: <bool> + Enable or disable strict sigaltstack size checks + against the required signal frame size which + depends on the supported FPU features. This can + be used to filter out binaries which have + not yet been made aware of AT_MINSIGSTKSZ. + + sunrpc.min_resvport= + sunrpc.max_resvport= + [NFS,SUNRPC] + SunRPC servers often require that client requests + originate from a privileged port (i.e. a port in the + range 0 < portnr < 1024). + An administrator who wishes to reserve some of these + ports for other uses may adjust the range that the + kernel's sunrpc client considers to be privileged + using these two parameters to set the minimum and + maximum port values. + + sunrpc.svc_rpc_per_connection_limit= + [NFS,SUNRPC] + Limit the number of requests that the server will + process in parallel from a single connection. + The default value is 0 (no limit). + + sunrpc.pool_mode= + [NFS] + Control how the NFS server code allocates CPUs to + service thread pools. Depending on how many NICs + you have and where their interrupts are bound, this + option will affect which CPUs will do NFS serving. + Note: this parameter cannot be changed while the + NFS server is running. + + auto the server chooses an appropriate mode + automatically using heuristics + global a single global pool contains all CPUs + percpu one pool for each CPU + pernode one pool for each NUMA node (equivalent + to global on non-NUMA machines) + + sunrpc.tcp_slot_table_entries= + sunrpc.udp_slot_table_entries= + [NFS,SUNRPC] + Sets the upper limit on the number of simultaneous + RPC calls that can be sent from the client to a + server. Increasing these values may allow you to + improve throughput, but will also increase the + amount of memory reserved for use by the client. + + suspend.pm_test_delay= + [SUSPEND] + Sets the number of seconds to remain in a suspend test + mode before resuming the system (see + /sys/power/pm_test). Only available when CONFIG_PM_DEBUG + is set. Default value is 5. + + svm= [PPC] + Format: { on | off | y | n | 1 | 0 } + This parameter controls use of the Protected + Execution Facility on pSeries. + + swiotlb= [ARM,IA-64,PPC,MIPS,X86] + Format: { <int> [,<int>] | force | noforce } + <int> -- Number of I/O TLB slabs + <int> -- Second integer after comma. Number of swiotlb + areas with their own lock. Will be rounded up + to a power of 2. + force -- force using of bounce buffers even if they + wouldn't be automatically used by the kernel + noforce -- Never use bounce buffers (for debugging) + + switches= [HW,M68k] + + sysctl.*= [KNL] + Set a sysctl parameter, right before loading the init + process, as if the value was written to the respective + /proc/sys/... file. Both '.' and '/' are recognized as + separators. Unrecognized parameters and invalid values + are reported in the kernel log. Sysctls registered + later by a loaded module cannot be set this way. + Example: sysctl.vm.swappiness=40 + + sysfs.deprecated=0|1 [KNL] + Enable/disable old style sysfs layout for old udev + on older distributions. When this option is enabled + very new udev will not work anymore. When this option + is disabled (or CONFIG_SYSFS_DEPRECATED not compiled) + in older udev will not work anymore. + Default depends on CONFIG_SYSFS_DEPRECATED_V2 set in + the kernel configuration. + + sysrq_always_enabled + [KNL] + Ignore sysrq setting - this boot parameter will + neutralize any effect of /proc/sys/kernel/sysrq. + Useful for debugging. + + tcpmhash_entries= [KNL,NET] + Set the number of tcp_metrics_hash slots. + Default value is 8192 or 16384 depending on total + ram pages. This is used to specify the TCP metrics + cache size. See Documentation/networking/ip-sysctl.rst + "tcp_no_metrics_save" section for more details. + + tdfx= [HW,DRM] + + test_suspend= [SUSPEND] + Format: { "mem" | "standby" | "freeze" }[,N] + Specify "mem" (for Suspend-to-RAM) or "standby" (for + standby suspend) or "freeze" (for suspend type freeze) + as the system sleep state during system startup with + the optional capability to repeat N number of times. + The system is woken from this state using a + wakeup-capable RTC alarm. + + thash_entries= [KNL,NET] + Set number of hash buckets for TCP connection + + thermal.act= [HW,ACPI] + -1: disable all active trip points in all thermal zones + <degrees C>: override all lowest active trip points + + thermal.crt= [HW,ACPI] + -1: disable all critical trip points in all thermal zones + <degrees C>: override all critical trip points + + thermal.off= [HW,ACPI] + 1: disable ACPI thermal control + + thermal.psv= [HW,ACPI] + -1: disable all passive trip points + <degrees C>: override all passive trip points to this + value + + thermal.tzp= [HW,ACPI] + Specify global default ACPI thermal zone polling rate + <deci-seconds>: poll all this frequency + 0: no polling (default) + + threadirqs [KNL] + Force threading of all interrupt handlers except those + marked explicitly IRQF_NO_THREAD. + + topology= [S390] + Format: {off | on} + Specify if the kernel should make use of the cpu + topology information if the hardware supports this. + The scheduler will make use of this information and + e.g. base its process migration decisions on it. + Default is on. + + topology_updates= [KNL, PPC, NUMA] + Format: {off} + Specify if the kernel should ignore (off) + topology updates sent by the hypervisor to this + LPAR. + + torture.disable_onoff_at_boot= [KNL] + Prevent the CPU-hotplug component of torturing + until after init has spawned. + + torture.ftrace_dump_at_shutdown= [KNL] + Dump the ftrace buffer at torture-test shutdown, + even if there were no errors. This can be a + very costly operation when many torture tests + are running concurrently, especially on systems + with rotating-rust storage. + + torture.verbose_sleep_frequency= [KNL] + Specifies how many verbose printk()s should be + emitted between each sleep. The default of zero + disables verbose-printk() sleeping. + + torture.verbose_sleep_duration= [KNL] + Duration of each verbose-printk() sleep in jiffies. + + tp720= [HW,PS2] + + tpm_suspend_pcr=[HW,TPM] + Format: integer pcr id + Specify that at suspend time, the tpm driver + should extend the specified pcr with zeros, + as a workaround for some chips which fail to + flush the last written pcr on TPM_SaveState. + This will guarantee that all the other pcrs + are saved. + + tp_printk [FTRACE] + Have the tracepoints sent to printk as well as the + tracing ring buffer. This is useful for early boot up + where the system hangs or reboots and does not give the + option for reading the tracing buffer or performing a + ftrace_dump_on_oops. + + To turn off having tracepoints sent to printk, + echo 0 > /proc/sys/kernel/tracepoint_printk + Note, echoing 1 into this file without the + tracepoint_printk kernel cmdline option has no effect. + + The tp_printk_stop_on_boot (see below) can also be used + to stop the printing of events to console at + late_initcall_sync. + + ** CAUTION ** + + Having tracepoints sent to printk() and activating high + frequency tracepoints such as irq or sched, can cause + the system to live lock. + + tp_printk_stop_on_boot [FTRACE] + When tp_printk (above) is set, it can cause a lot of noise + on the console. It may be useful to only include the + printing of events during boot up, as user space may + make the system inoperable. + + This command line option will stop the printing of events + to console at the late_initcall_sync() time frame. + + trace_buf_size=nn[KMG] + [FTRACE] will set tracing buffer size on each cpu. + + trace_clock= [FTRACE] Set the clock used for tracing events + at boot up. + local - Use the per CPU time stamp counter + (converted into nanoseconds). Fast, but + depending on the architecture, may not be + in sync between CPUs. + global - Event time stamps are synchronize across + CPUs. May be slower than the local clock, + but better for some race conditions. + counter - Simple counting of events (1, 2, ..) + note, some counts may be skipped due to the + infrastructure grabbing the clock more than + once per event. + uptime - Use jiffies as the time stamp. + perf - Use the same clock that perf uses. + mono - Use ktime_get_mono_fast_ns() for time stamps. + mono_raw - Use ktime_get_raw_fast_ns() for time + stamps. + boot - Use ktime_get_boot_fast_ns() for time stamps. + Architectures may add more clocks. See + Documentation/trace/ftrace.rst for more details. + + trace_event=[event-list] + [FTRACE] Set and start specified trace events in order + to facilitate early boot debugging. The event-list is a + comma-separated list of trace events to enable. See + also Documentation/trace/events.rst + + trace_options=[option-list] + [FTRACE] Enable or disable tracer options at boot. + The option-list is a comma delimited list of options + that can be enabled or disabled just as if you were + to echo the option name into + + /sys/kernel/debug/tracing/trace_options + + For example, to enable stacktrace option (to dump the + stack trace of each event), add to the command line: + + trace_options=stacktrace + + See also Documentation/trace/ftrace.rst "trace options" + section. + + traceoff_on_warning + [FTRACE] enable this option to disable tracing when a + warning is hit. This turns off "tracing_on". Tracing can + be enabled again by echoing '1' into the "tracing_on" + file located in /sys/kernel/debug/tracing/ + + This option is useful, as it disables the trace before + the WARNING dump is called, which prevents the trace to + be filled with content caused by the warning output. + + This option can also be set at run time via the sysctl + option: kernel/traceoff_on_warning + + transparent_hugepage= + [KNL] + Format: [always|madvise|never] + Can be used to control the default behavior of the system + with respect to transparent hugepages. + See Documentation/admin-guide/mm/transhuge.rst + for more details. + + trusted.source= [KEYS] + Format: <string> + This parameter identifies the trust source as a backend + for trusted keys implementation. Supported trust + sources: + - "tpm" + - "tee" + - "caam" + If not specified then it defaults to iterating through + the trust source list starting with TPM and assigns the + first trust source as a backend which is initialized + successfully during iteration. + + trusted.rng= [KEYS] + Format: <string> + The RNG used to generate key material for trusted keys. + Can be one of: + - "kernel" + - the same value as trusted.source: "tpm" or "tee" + - "default" + If not specified, "default" is used. In this case, + the RNG's choice is left to each individual trust source. + + tsc= Disable clocksource stability checks for TSC. + Format: <string> + [x86] reliable: mark tsc clocksource as reliable, this + disables clocksource verification at runtime, as well + as the stability checks done at bootup. Used to enable + high-resolution timer mode on older hardware, and in + virtualized environment. + [x86] noirqtime: Do not use TSC to do irq accounting. + Used to run time disable IRQ_TIME_ACCOUNTING on any + platforms where RDTSC is slow and this accounting + can add overhead. + [x86] unstable: mark the TSC clocksource as unstable, this + marks the TSC unconditionally unstable at bootup and + avoids any further wobbles once the TSC watchdog notices. + [x86] nowatchdog: disable clocksource watchdog. Used + in situations with strict latency requirements (where + interruptions from clocksource watchdog are not + acceptable). + + tsc_early_khz= [X86] Skip early TSC calibration and use the given + value instead. Useful when the early TSC frequency discovery + procedure is not reliable, such as on overclocked systems + with CPUID.16h support and partial CPUID.15h support. + Format: <unsigned int> + + tsx= [X86] Control Transactional Synchronization + Extensions (TSX) feature in Intel processors that + support TSX control. + + This parameter controls the TSX feature. The options are: + + on - Enable TSX on the system. Although there are + mitigations for all known security vulnerabilities, + TSX has been known to be an accelerator for + several previous speculation-related CVEs, and + so there may be unknown security risks associated + with leaving it enabled. + + off - Disable TSX on the system. (Note that this + option takes effect only on newer CPUs which are + not vulnerable to MDS, i.e., have + MSR_IA32_ARCH_CAPABILITIES.MDS_NO=1 and which get + the new IA32_TSX_CTRL MSR through a microcode + update. This new MSR allows for the reliable + deactivation of the TSX functionality.) + + auto - Disable TSX if X86_BUG_TAA is present, + otherwise enable TSX on the system. + + Not specifying this option is equivalent to tsx=off. + + See Documentation/admin-guide/hw-vuln/tsx_async_abort.rst + for more details. + + tsx_async_abort= [X86,INTEL] Control mitigation for the TSX Async + Abort (TAA) vulnerability. + + Similar to Micro-architectural Data Sampling (MDS) + certain CPUs that support Transactional + Synchronization Extensions (TSX) are vulnerable to an + exploit against CPU internal buffers which can forward + information to a disclosure gadget under certain + conditions. + + In vulnerable processors, the speculatively forwarded + data can be used in a cache side channel attack, to + access data to which the attacker does not have direct + access. + + This parameter controls the TAA mitigation. The + options are: + + full - Enable TAA mitigation on vulnerable CPUs + if TSX is enabled. + + full,nosmt - Enable TAA mitigation and disable SMT on + vulnerable CPUs. If TSX is disabled, SMT + is not disabled because CPU is not + vulnerable to cross-thread TAA attacks. + off - Unconditionally disable TAA mitigation + + On MDS-affected machines, tsx_async_abort=off can be + prevented by an active MDS mitigation as both vulnerabilities + are mitigated with the same mechanism so in order to disable + this mitigation, you need to specify mds=off too. + + Not specifying this option is equivalent to + tsx_async_abort=full. On CPUs which are MDS affected + and deploy MDS mitigation, TAA mitigation is not + required and doesn't provide any additional + mitigation. + + For details see: + Documentation/admin-guide/hw-vuln/tsx_async_abort.rst + + turbografx.map[2|3]= [HW,JOY] + TurboGraFX parallel port interface + Format: + <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7> + See also Documentation/input/devices/joystick-parport.rst + + udbg-immortal [PPC] When debugging early kernel crashes that + happen after console_init() and before a proper + console driver takes over, this boot options might + help "seeing" what's going on. + + uhash_entries= [KNL,NET] + Set number of hash buckets for UDP/UDP-Lite connections + + uhci-hcd.ignore_oc= + [USB] Ignore overcurrent events (default N). + Some badly-designed motherboards generate lots of + bogus events, for ports that aren't wired to + anything. Set this parameter to avoid log spamming. + Note that genuine overcurrent events won't be + reported either. + + unknown_nmi_panic + [X86] Cause panic on unknown NMI. + + usbcore.authorized_default= + [USB] Default USB device authorization: + (default -1 = authorized except for wireless USB, + 0 = not authorized, 1 = authorized, 2 = authorized + if device connected to internal port) + + usbcore.autosuspend= + [USB] The autosuspend time delay (in seconds) used + for newly-detected USB devices (default 2). This + is the time required before an idle device will be + autosuspended. Devices for which the delay is set + to a negative value won't be autosuspended at all. + + usbcore.usbfs_snoop= + [USB] Set to log all usbfs traffic (default 0 = off). + + usbcore.usbfs_snoop_max= + [USB] Maximum number of bytes to snoop in each URB + (default = 65536). + + usbcore.blinkenlights= + [USB] Set to cycle leds on hubs (default 0 = off). + + usbcore.old_scheme_first= + [USB] Start with the old device initialization + scheme (default 0 = off). + + usbcore.usbfs_memory_mb= + [USB] Memory limit (in MB) for buffers allocated by + usbfs (default = 16, 0 = max = 2047). + + usbcore.use_both_schemes= + [USB] Try the other device initialization scheme + if the first one fails (default 1 = enabled). + + usbcore.initial_descriptor_timeout= + [USB] Specifies timeout for the initial 64-byte + USB_REQ_GET_DESCRIPTOR request in milliseconds + (default 5000 = 5.0 seconds). + + usbcore.nousb [USB] Disable the USB subsystem + + usbcore.quirks= + [USB] A list of quirk entries to augment the built-in + usb core quirk list. List entries are separated by + commas. Each entry has the form + VendorID:ProductID:Flags. The IDs are 4-digit hex + numbers and Flags is a set of letters. Each letter + will change the built-in quirk; setting it if it is + clear and clearing it if it is set. The letters have + the following meanings: + a = USB_QUIRK_STRING_FETCH_255 (string + descriptors must not be fetched using + a 255-byte read); + b = USB_QUIRK_RESET_RESUME (device can't resume + correctly so reset it instead); + c = USB_QUIRK_NO_SET_INTF (device can't handle + Set-Interface requests); + d = USB_QUIRK_CONFIG_INTF_STRINGS (device can't + handle its Configuration or Interface + strings); + e = USB_QUIRK_RESET (device can't be reset + (e.g morph devices), don't use reset); + f = USB_QUIRK_HONOR_BNUMINTERFACES (device has + more interface descriptions than the + bNumInterfaces count, and can't handle + talking to these interfaces); + g = USB_QUIRK_DELAY_INIT (device needs a pause + during initialization, after we read + the device descriptor); + h = USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL (For + high speed and super speed interrupt + endpoints, the USB 2.0 and USB 3.0 spec + require the interval in microframes (1 + microframe = 125 microseconds) to be + calculated as interval = 2 ^ + (bInterval-1). + Devices with this quirk report their + bInterval as the result of this + calculation instead of the exponent + variable used in the calculation); + i = USB_QUIRK_DEVICE_QUALIFIER (device can't + handle device_qualifier descriptor + requests); + j = USB_QUIRK_IGNORE_REMOTE_WAKEUP (device + generates spurious wakeup, ignore + remote wakeup capability); + k = USB_QUIRK_NO_LPM (device can't handle Link + Power Management); + l = USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL + (Device reports its bInterval as linear + frames instead of the USB 2.0 + calculation); + m = USB_QUIRK_DISCONNECT_SUSPEND (Device needs + to be disconnected before suspend to + prevent spurious wakeup); + n = USB_QUIRK_DELAY_CTRL_MSG (Device needs a + pause after every control message); + o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra + delay after resetting its port); + Example: quirks=0781:5580:bk,0a5c:5834:gij + + usbhid.mousepoll= + [USBHID] The interval which mice are to be polled at. + + usbhid.jspoll= + [USBHID] The interval which joysticks are to be polled at. + + usbhid.kbpoll= + [USBHID] The interval which keyboards are to be polled at. + + usb-storage.delay_use= + [UMS] The delay in seconds before a new device is + scanned for Logical Units (default 1). + + usb-storage.quirks= + [UMS] A list of quirks entries to supplement or + override the built-in unusual_devs list. List + entries are separated by commas. Each entry has + the form VID:PID:Flags where VID and PID are Vendor + and Product ID values (4-digit hex numbers) and + Flags is a set of characters, each corresponding + to a common usb-storage quirk flag as follows: + a = SANE_SENSE (collect more than 18 bytes + of sense data, not on uas); + b = BAD_SENSE (don't collect more than 18 + bytes of sense data, not on uas); + c = FIX_CAPACITY (decrease the reported + device capacity by one sector); + d = NO_READ_DISC_INFO (don't use + READ_DISC_INFO command, not on uas); + e = NO_READ_CAPACITY_16 (don't use + READ_CAPACITY_16 command); + f = NO_REPORT_OPCODES (don't use report opcodes + command, uas only); + g = MAX_SECTORS_240 (don't transfer more than + 240 sectors at a time, uas only); + h = CAPACITY_HEURISTICS (decrease the + reported device capacity by one + sector if the number is odd); + i = IGNORE_DEVICE (don't bind to this + device); + j = NO_REPORT_LUNS (don't use report luns + command, uas only); + k = NO_SAME (do not use WRITE_SAME, uas only) + l = NOT_LOCKABLE (don't try to lock and + unlock ejectable media, not on uas); + m = MAX_SECTORS_64 (don't transfer more + than 64 sectors = 32 KB at a time, + not on uas); + n = INITIAL_READ10 (force a retry of the + initial READ(10) command, not on uas); + o = CAPACITY_OK (accept the capacity + reported by the device, not on uas); + p = WRITE_CACHE (the device cache is ON + by default, not on uas); + r = IGNORE_RESIDUE (the device reports + bogus residue values, not on uas); + s = SINGLE_LUN (the device has only one + Logical Unit); + t = NO_ATA_1X (don't allow ATA(12) and ATA(16) + commands, uas only); + u = IGNORE_UAS (don't bind to the uas driver); + w = NO_WP_DETECT (don't test whether the + medium is write-protected). + y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE + even if the device claims no cache, + not on uas) + Example: quirks=0419:aaf5:rl,0421:0433:rc + + user_debug= [KNL,ARM] + Format: <int> + See arch/arm/Kconfig.debug help text. + 1 - undefined instruction events + 2 - system calls + 4 - invalid data aborts + 8 - SIGSEGV faults + 16 - SIGBUS faults + Example: user_debug=31 + + userpte= + [X86] Flags controlling user PTE allocations. + + nohigh = do not allocate PTE pages in + HIGHMEM regardless of setting + of CONFIG_HIGHPTE. + + vdso= [X86,SH,SPARC] + On X86_32, this is an alias for vdso32=. Otherwise: + + vdso=1: enable VDSO (the default) + vdso=0: disable VDSO mapping + + vdso32= [X86] Control the 32-bit vDSO + vdso32=1: enable 32-bit VDSO + vdso32=0 or vdso32=2: disable 32-bit VDSO + + See the help text for CONFIG_COMPAT_VDSO for more + details. If CONFIG_COMPAT_VDSO is set, the default is + vdso32=0; otherwise, the default is vdso32=1. + + For compatibility with older kernels, vdso32=2 is an + alias for vdso32=0. + + Try vdso32=0 if you encounter an error that says: + dl_main: Assertion `(void *) ph->p_vaddr == _rtld_local._dl_sysinfo_dso' failed! + + vector= [IA-64,SMP] + vector=percpu: enable percpu vector domain + + video= [FB] Frame buffer configuration + See Documentation/fb/modedb.rst. + + video.brightness_switch_enabled= [ACPI] + Format: [0|1] + If set to 1, on receiving an ACPI notify event + generated by hotkey, video driver will adjust brightness + level and then send out the event to user space through + the allocated input device. If set to 0, video driver + will only send out the event without touching backlight + brightness level. + default: 1 + + virtio_mmio.device= + [VMMIO] Memory mapped virtio (platform) device. + + <size>@<baseaddr>:<irq>[:<id>] + where: + <size> := size (can use standard suffixes + like K, M and G) + <baseaddr> := physical base address + <irq> := interrupt number (as passed to + request_irq()) + <id> := (optional) platform device id + example: + virtio_mmio.device=1K@0x100b0000:48:7 + + Can be used multiple times for multiple devices. + + vga= [BOOT,X86-32] Select a particular video mode + See Documentation/x86/boot.rst and + Documentation/admin-guide/svga.rst. + Use vga=ask for menu. + This is actually a boot loader parameter; the value is + passed to the kernel using a special protocol. + + vm_debug[=options] [KNL] Available with CONFIG_DEBUG_VM=y. + May slow down system boot speed, especially when + enabled on systems with a large amount of memory. + All options are enabled by default, and this + interface is meant to allow for selectively + enabling or disabling specific virtual memory + debugging features. + + Available options are: + P Enable page structure init time poisoning + - Disable all of the above options + + vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact + size of <nn>. This can be used to increase the + minimum size (128MB on x86). It can also be used to + decrease the size and leave more room for directly + mapped kernel RAM. + + vmcp_cma=nn[MG] [KNL,S390] + Sets the memory size reserved for contiguous memory + allocations for the vmcp device driver. + + vmhalt= [KNL,S390] Perform z/VM CP command after system halt. + Format: <command> + + vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic. + Format: <command> + + vmpoff= [KNL,S390] Perform z/VM CP command after power off. + Format: <command> + + vsyscall= [X86-64] + Controls the behavior of vsyscalls (i.e. calls to + fixed addresses of 0xffffffffff600x00 from legacy + code). Most statically-linked binaries and older + versions of glibc use these calls. Because these + functions are at fixed addresses, they make nice + targets for exploits that can control RIP. + + emulate [default] Vsyscalls turn into traps and are + emulated reasonably safely. The vsyscall + page is readable. + + xonly Vsyscalls turn into traps and are + emulated reasonably safely. The vsyscall + page is not readable. + + none Vsyscalls don't work at all. This makes + them quite hard to use for exploits but + might break your system. + + vt.color= [VT] Default text color. + Format: 0xYX, X = foreground, Y = background. + Default: 0x07 = light gray on black. + + vt.cur_default= [VT] Default cursor shape. + Format: 0xCCBBAA, where AA, BB, and CC are the same as + the parameters of the <Esc>[?A;B;Cc escape sequence; + see VGA-softcursor.txt. Default: 2 = underline. + + vt.default_blu= [VT] + Format: <blue0>,<blue1>,<blue2>,...,<blue15> + Change the default blue palette of the console. + This is a 16-member array composed of values + ranging from 0-255. + + vt.default_grn= [VT] + Format: <green0>,<green1>,<green2>,...,<green15> + Change the default green palette of the console. + This is a 16-member array composed of values + ranging from 0-255. + + vt.default_red= [VT] + Format: <red0>,<red1>,<red2>,...,<red15> + Change the default red palette of the console. + This is a 16-member array composed of values + ranging from 0-255. + + vt.default_utf8= + [VT] + Format=<0|1> + Set system-wide default UTF-8 mode for all tty's. + Default is 1, i.e. UTF-8 mode is enabled for all + newly opened terminals. + + vt.global_cursor_default= + [VT] + Format=<-1|0|1> + Set system-wide default for whether a cursor + is shown on new VTs. Default is -1, + i.e. cursors will be created by default unless + overridden by individual drivers. 0 will hide + cursors, 1 will display them. + + vt.italic= [VT] Default color for italic text; 0-15. + Default: 2 = green. + + vt.underline= [VT] Default color for underlined text; 0-15. + Default: 3 = cyan. + + watchdog timers [HW,WDT] For information on watchdog timers, + see Documentation/watchdog/watchdog-parameters.rst + or other driver-specific files in the + Documentation/watchdog/ directory. + + watchdog_thresh= + [KNL] + Set the hard lockup detector stall duration + threshold in seconds. The soft lockup detector + threshold is set to twice the value. A value of 0 + disables both lockup detectors. Default is 10 + seconds. + + workqueue.watchdog_thresh= + If CONFIG_WQ_WATCHDOG is configured, workqueue can + warn stall conditions and dump internal state to + help debugging. 0 disables workqueue stall + detection; otherwise, it's the stall threshold + duration in seconds. The default value is 30 and + it can be updated at runtime by writing to the + corresponding sysfs file. + + workqueue.disable_numa + By default, all work items queued to unbound + workqueues are affine to the NUMA nodes they're + issued on, which results in better behavior in + general. If NUMA affinity needs to be disabled for + whatever reason, this option can be used. Note + that this also can be controlled per-workqueue for + workqueues visible under /sys/bus/workqueue/. + + workqueue.power_efficient + Per-cpu workqueues are generally preferred because + they show better performance thanks to cache + locality; unfortunately, per-cpu workqueues tend to + be more power hungry than unbound workqueues. + + Enabling this makes the per-cpu workqueues which + were observed to contribute significantly to power + consumption unbound, leading to measurably lower + power usage at the cost of small performance + overhead. + + The default value of this parameter is determined by + the config option CONFIG_WQ_POWER_EFFICIENT_DEFAULT. + + workqueue.debug_force_rr_cpu + Workqueue used to implicitly guarantee that work + items queued without explicit CPU specified are put + on the local CPU. This guarantee is no longer true + and while local CPU is still preferred work items + may be put on foreign CPUs. This debug option + forces round-robin CPU selection to flush out + usages which depend on the now broken guarantee. + When enabled, memory and cache locality will be + impacted. + + x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of + default x2apic cluster mode on platforms + supporting x2apic. + + xen_512gb_limit [KNL,X86-64,XEN] + Restricts the kernel running paravirtualized under Xen + to use only up to 512 GB of RAM. The reason to do so is + crash analysis tools and Xen tools for doing domain + save/restore/migration must be enabled to handle larger + domains. + + xen_emul_unplug= [HW,X86,XEN] + Unplug Xen emulated devices + Format: [unplug0,][unplug1] + ide-disks -- unplug primary master IDE devices + aux-ide-disks -- unplug non-primary-master IDE devices + nics -- unplug network devices + all -- unplug all emulated devices (NICs and IDE disks) + unnecessary -- unplugging emulated devices is + unnecessary even if the host did not respond to + the unplug protocol + never -- do not unplug even if version check succeeds + + xen_legacy_crash [X86,XEN] + Crash from Xen panic notifier, without executing late + panic() code such as dumping handler. + + xen_msr_safe= [X86,XEN] + Format: <bool> + Select whether to always use non-faulting (safe) MSR + access functions when running as Xen PV guest. The + default value is controlled by CONFIG_XEN_PV_MSR_SAFE. + + xen_nopvspin [X86,XEN] + Disables the qspinlock slowpath using Xen PV optimizations. + This parameter is obsoleted by "nopvspin" parameter, which + has equivalent effect for XEN platform. + + xen_nopv [X86] + Disables the PV optimizations forcing the HVM guest to + run as generic HVM guest with no PV drivers. + This option is obsoleted by the "nopv" option, which + has equivalent effect for XEN platform. + + xen_no_vector_callback + [KNL,X86,XEN] Disable the vector callback for Xen + event channel interrupts. + + xen_scrub_pages= [XEN] + Boolean option to control scrubbing pages before giving them back + to Xen, for use by other domains. Can be also changed at runtime + with /sys/devices/system/xen_memory/xen_memory0/scrub_pages. + Default value controlled with CONFIG_XEN_SCRUB_PAGES_DEFAULT. + + xen_timer_slop= [X86-64,XEN] + Set the timer slop (in nanoseconds) for the virtual Xen + timers (default is 100000). This adjusts the minimum + delta of virtualized Xen timers, where lower values + improve timer resolution at the expense of processing + more timer interrupts. + + xen.balloon_boot_timeout= [XEN] + The time (in seconds) to wait before giving up to boot + in case initial ballooning fails to free enough memory. + Applies only when running as HVM or PVH guest and + started with less memory configured than allowed at + max. Default is 180. + + xen.event_eoi_delay= [XEN] + How long to delay EOI handling in case of event + storms (jiffies). Default is 10. + + xen.event_loop_timeout= [XEN] + After which time (jiffies) the event handling loop + should start to delay EOI handling. Default is 2. + + xen.fifo_events= [XEN] + Boolean parameter to disable using fifo event handling + even if available. Normally fifo event handling is + preferred over the 2-level event handling, as it is + fairer and the number of possible event channels is + much higher. Default is on (use fifo events). + + nopv= [X86,XEN,KVM,HYPER_V,VMWARE] + Disables the PV optimizations forcing the guest to run + as generic guest with no PV drivers. Currently support + XEN HVM, KVM, HYPER_V and VMWARE guest. + + nopvspin [X86,XEN,KVM] + Disables the qspinlock slow path using PV optimizations + which allow the hypervisor to 'idle' the guest on lock + contention. + + xirc2ps_cs= [NET,PCMCIA] + Format: + <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]] + + xive= [PPC] + By default on POWER9 and above, the kernel will + natively use the XIVE interrupt controller. This option + allows the fallback firmware mode to be used: + + off Fallback to firmware control of XIVE interrupt + controller on both pseries and powernv + platforms. Only useful on POWER9 and above. + + xive.store-eoi=off [PPC] + By default on POWER10 and above, the kernel will use + stores for EOI handling when the XIVE interrupt mode + is active. This option allows the XIVE driver to use + loads instead, as on POWER9. + + xhci-hcd.quirks [USB,KNL] + A hex value specifying bitmask with supplemental xhci + host controller quirks. Meaning of each bit can be + consulted in header drivers/usb/host/xhci.h. + + xmon [PPC] + Format: { early | on | rw | ro | off } + Controls if xmon debugger is enabled. Default is off. + Passing only "xmon" is equivalent to "xmon=early". + early Call xmon as early as possible on boot; xmon + debugger is called from setup_arch(). + on xmon debugger hooks will be installed so xmon + is only called on a kernel crash. Default mode, + i.e. either "ro" or "rw" mode, is controlled + with CONFIG_XMON_DEFAULT_RO_MODE. + rw xmon debugger hooks will be installed so xmon + is called only on a kernel crash, mode is write, + meaning SPR registers, memory and, other data + can be written using xmon commands. + ro same as "rw" option above but SPR registers, + memory, and other data can't be written using + xmon commands. + off xmon is disabled. + + amd_pstate= [X86] + disable + Do not enable amd_pstate as the default + scaling driver for the supported processors + passive + Use amd_pstate as a scaling driver, driver requests a + desired performance on this abstract scale and the power + management firmware translates the requests into actual + hardware states (core frequency, data fabric and memory + clocks etc.) |