summaryrefslogtreecommitdiffstats
path: root/Documentation/admin-guide/perf/imx-ddr.rst
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/admin-guide/perf/imx-ddr.rst71
1 files changed, 71 insertions, 0 deletions
diff --git a/Documentation/admin-guide/perf/imx-ddr.rst b/Documentation/admin-guide/perf/imx-ddr.rst
new file mode 100644
index 000000000..90926d0fb
--- /dev/null
+++ b/Documentation/admin-guide/perf/imx-ddr.rst
@@ -0,0 +1,71 @@
+=====================================================
+Freescale i.MX8 DDR Performance Monitoring Unit (PMU)
+=====================================================
+
+There are no performance counters inside the DRAM controller, so performance
+signals are brought out to the edge of the controller where a set of 4 x 32 bit
+counters is implemented. This is controlled by the CSV modes programmed in counter
+control register which causes a large number of PERF signals to be generated.
+
+Selection of the value for each counter is done via the config registers. There
+is one register for each counter. Counter 0 is special in that it always counts
+“time” and when expired causes a lock on itself and the other counters and an
+interrupt is raised. If any other counter overflows, it continues counting, and
+no interrupt is raised.
+
+The "format" directory describes format of the config (event ID) and config1
+(AXI filtering) fields of the perf_event_attr structure, see /sys/bus/event_source/
+devices/imx8_ddr0/format/. The "events" directory describes the events types
+hardware supported that can be used with perf tool, see /sys/bus/event_source/
+devices/imx8_ddr0/events/. The "caps" directory describes filter features implemented
+in DDR PMU, see /sys/bus/events_source/devices/imx8_ddr0/caps/.
+
+ .. code-block:: bash
+
+ perf stat -a -e imx8_ddr0/cycles/ cmd
+ perf stat -a -e imx8_ddr0/read/,imx8_ddr0/write/ cmd
+
+AXI filtering is only used by CSV modes 0x41 (axid-read) and 0x42 (axid-write)
+to count reading or writing matches filter setting. Filter setting is various
+from different DRAM controller implementations, which is distinguished by quirks
+in the driver. You also can dump info from userspace, filter in "caps" directory
+indicates whether PMU supports AXI ID filter or not; enhanced_filter indicates
+whether PMU supports enhanced AXI ID filter or not. Value 0 for un-supported, and
+value 1 for supported.
+
+* With DDR_CAP_AXI_ID_FILTER quirk(filter: 1, enhanced_filter: 0).
+ Filter is defined with two configuration parts:
+ --AXI_ID defines AxID matching value.
+ --AXI_MASKING defines which bits of AxID are meaningful for the matching.
+
+ - 0: corresponding bit is masked.
+ - 1: corresponding bit is not masked, i.e. used to do the matching.
+
+ AXI_ID and AXI_MASKING are mapped on DPCR1 register in performance counter.
+ When non-masked bits are matching corresponding AXI_ID bits then counter is
+ incremented. Perf counter is incremented if::
+
+ AxID && AXI_MASKING == AXI_ID && AXI_MASKING
+
+ This filter doesn't support filter different AXI ID for axid-read and axid-write
+ event at the same time as this filter is shared between counters.
+
+ .. code-block:: bash
+
+ perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
+ perf stat -a -e imx8_ddr0/axid-write,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
+
+ .. note::
+
+ axi_mask is inverted in userspace(i.e. set bits are bits to mask), and
+ it will be reverted in driver automatically. so that the user can just specify
+ axi_id to monitor a specific id, rather than having to specify axi_mask.
+
+ .. code-block:: bash
+
+ perf stat -a -e imx8_ddr0/axid-read,axi_id=0x12/ cmd, which will monitor ARID=0x12
+
+* With DDR_CAP_AXI_ID_FILTER_ENHANCED quirk(filter: 1, enhanced_filter: 1).
+ This is an extension to the DDR_CAP_AXI_ID_FILTER quirk which permits
+ counting the number of bytes (as opposed to the number of bursts) from DDR
+ read and write transactions concurrently with another set of data counters.