diff options
Diffstat (limited to '')
100 files changed, 6604 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt new file mode 100644 index 000000000..973362eb3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt @@ -0,0 +1,72 @@ +GPIO controllers on MPC8xxx SoCs + +This is for the non-QE/CPM/GUTs GPIO controllers as found on +8349, 8572, 8610 and compatible. + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. +See bindings/gpio/gpio.txt for details of how to specify GPIO +information for devices. + +The GPIO module usually is connected to the SoC's internal interrupt +controller, see bindings/interrupt-controller/interrupts.txt (the +interrupt client nodes section) for details how to specify this GPIO +module's interrupt. + +The GPIO module may serve as another interrupt controller (cascaded to +the SoC's internal interrupt controller). See the interrupt controller +nodes section in bindings/interrupt-controller/interrupts.txt for +details. + +Required properties: +- compatible: "fsl,<chip>-gpio" followed by "fsl,mpc8349-gpio" + for 83xx, "fsl,mpc8572-gpio" for 85xx, or + "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells: Should be two. The first cell is the pin number + and the second cell is used to specify optional + parameters (currently unused). +- interrupts: Interrupt mapping for GPIO IRQ. +- gpio-controller: Marks the port as GPIO controller. + +Optional properties: +- interrupt-controller: Empty boolean property which marks the GPIO + module as an IRQ controller. +- #interrupt-cells: Should be two. Defines the number of integer + cells required to specify an interrupt within + this interrupt controller. The first cell + defines the pin number, the second cell + defines additional flags (trigger type, + trigger polarity). Note that the available + set of trigger conditions supported by the + GPIO module depends on the actual SoC. + +Example of gpio-controller nodes for a MPC8347 SoC: + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupt-parent = <&ipic>; + interrupts = <74 0x8>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupt-parent = <&ipic>; + interrupts = <75 0x8>; + gpio-controller; + }; + +Example of a peripheral using the GPIO module as an IRQ controller: + + funkyfpga@0 { + compatible = "funky-fpga"; + ... + interrupt-parent = <&gpio1>; + interrupts = <4 3>; + }; diff --git a/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt new file mode 100644 index 000000000..ce19c5660 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt @@ -0,0 +1,35 @@ +* Abilis TB10x GPIO controller + +Required Properties: +- compatible: Should be "abilis,tb10x-gpio" +- reg: Address and length of the register set for the device +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). +- abilis,ngpio: the number of GPIO pins this driver controls. + +Optional Properties: +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be <1>. Interrupts are triggered on both edges. +- interrupts: Defines the interrupt line connecting this GPIO controller to + its parent interrupt controller. + +GPIO ranges are specified as described in +Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + gpioa: gpio@ff140000 { + compatible = "abilis,tb10x-gpio"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&tb10x_ictl>; + interrupts = <27 2>; + reg = <0xFF140000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + abilis,ngpio = <3>; + gpio-ranges = <&iomux 0 0 0>; + gpio-ranges-group-names = "gpioa_pins"; + }; diff --git a/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml new file mode 100644 index 000000000..7c41d8e81 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/airoha,en7523-gpio.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/airoha,en7523-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Airoha EN7523 GPIO controller + +maintainers: + - John Crispin <john@phrozen.org> + +description: | + Airoha's GPIO controller on their ARM EN7523 SoCs consists of two banks of 32 + GPIOs. + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + items: + - const: airoha,en7523-gpio + + reg: + description: | + The first tuple points to the input register. + The second and third tuple point to the direction registers + The fourth tuple points to the output register + maxItems: 4 + + "#gpio-cells": + const: 2 + + gpio-controller: true + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + gpio0: gpio@1fbf0200 { + compatible = "airoha,en7523-gpio"; + reg = <0x1fbf0204 0x4>, + <0x1fbf0200 0x4>, + <0x1fbf0220 0x4>, + <0x1fbf0214 0x4>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio1: gpio@1fbf0270 { + compatible = "airoha,en7523-gpio"; + reg = <0x1fbf0270 0x4>, + <0x1fbf0260 0x4>, + <0x1fbf0264 0x4>, + <0x1fbf0278 0x4>; + gpio-controller; + #gpio-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml b/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml new file mode 100644 index 000000000..46bb12136 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Aspeed SGPIO controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: + This SGPIO controller is for ASPEED AST2400, AST2500 and AST2600 SoC, + AST2600 have two sgpio master one with 128 pins another one with 80 pins, + AST2500/AST2400 have one sgpio master with 80 pins. Each of the Serial + GPIO pins can be programmed to support the following options + - Support interrupt option for each input port and various interrupt + sensitivity option (level-high, level-low, edge-high, edge-low) + - Support reset tolerance option for each output port + - Directly connected to APB bus and its shift clock is from APB bus clock + divided by a programmable value. + - Co-work with external signal-chained TTL components (74LV165/74LV595) + +properties: + compatible: + enum: + - aspeed,ast2400-sgpio + - aspeed,ast2500-sgpio + - aspeed,ast2600-sgpiom + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + clocks: + maxItems: 1 + + ngpios: true + + bus-frequency: true + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - interrupts + - interrupt-controller + - ngpios + - clocks + - bus-frequency + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/aspeed-clock.h> + sgpio: sgpio@1e780200 { + #gpio-cells = <2>; + compatible = "aspeed,ast2500-sgpio"; + gpio-controller; + interrupts = <40>; + reg = <0x1e780200 0x0100>; + clocks = <&syscon ASPEED_CLK_APB>; + interrupt-controller; + ngpios = <80>; + bus-frequency = <12000000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml new file mode 100644 index 000000000..4d69f79df --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/brcm,bcm6345-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM6345 GPIO controller + +maintainers: + - Álvaro Fernández Rojas <noltari@gmail.com> + - Jonas Gorski <jonas.gorski@gmail.com> + +description: |+ + Bindings for Broadcom's BCM63xx memory-mapped GPIO controllers. + + These bindings can be used on any BCM63xx SoC. However, BCM6338 and BCM6345 + are the only ones which don't need a pinctrl driver. + + BCM6338 have 8-bit data and dirout registers, where GPIO state can be read + and/or written, and the direction changed from input to output. + BCM6345 have 16-bit data and dirout registers, where GPIO state can be read + and/or written, and the direction changed from input to output. + BCM6318, BCM6328, BCM6358, BCM6362, BCM6368 and BCM63268 have 32-bit data + and dirout registers, where GPIO state can be read and/or written, and the + direction changed from input to output. + +properties: + compatible: + enum: + - brcm,bcm6318-gpio + - brcm,bcm6328-gpio + - brcm,bcm6345-gpio + - brcm,bcm6358-gpio + - brcm,bcm6362-gpio + - brcm,bcm6368-gpio + - brcm,bcm63268-gpio + + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-ranges: + maxItems: 1 + + native-endian: true + + reg: + maxItems: 2 + + reg-names: + items: + - const: dirout + - const: dat + +required: + - compatible + - reg + - reg-names + - gpio-controller + - '#gpio-cells' + +additionalProperties: false + +examples: + - | + gpio@fffe0406 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0406 2>, <0xfffe040a 2>; + native-endian; + + gpio-controller; + #gpio-cells = <2>; + }; + + - | + gpio@0 { + compatible = "brcm,bcm63268-gpio"; + reg-names = "dirout", "dat"; + reg = <0x0 0x8>, <0x8 0x8>; + + gpio-controller; + gpio-ranges = <&pinctrl 0 0 52>; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml new file mode 100644 index 000000000..4a896ff7e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/brcm,brcmstb-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom STB "UPG GIO" GPIO controller + +description: > + The controller's registers are organized as sets of eight 32-bit + registers with each set controlling a bank of up to 32 pins. A single + interrupt is shared for all of the banks handled by the controller. + +maintainers: + - Doug Berger <opendmb@gmail.com> + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + compatible: + items: + - enum: + - brcm,bcm7445-gpio + - const: brcm,brcmstb-gpio + + reg: + maxItems: 1 + description: > + Define the base and range of the I/O address space containing + the brcmstb GPIO controller registers + + "#gpio-cells": + const: 2 + description: > + The first cell is the pin number (within the controller's + pin space), and the second is used for the following: + bit[0]: polarity (0 for active-high, 1 for active-low) + + gpio-controller: true + + brcm,gpio-bank-widths: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: > + Number of GPIO lines for each bank. Number of elements must + correspond to number of banks suggested by the 'reg' property. + + interrupts: + maxItems: 1 + description: > + The interrupt shared by all GPIO lines for this controller. + + "#interrupt-cells": + const: 2 + description: | + The first cell is the GPIO number, the second should specify + flags. The following subset of flags is supported: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + Valid combinations are 1, 2, 3, 4, 8. + + interrupt-controller: true + + wakeup-source: + type: boolean + description: > + GPIOs for this controller can be used as a wakeup source + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - "brcm,gpio-bank-widths" + +additionalProperties: false + +examples: + - | + upg_gio: gpio@f040a700 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf040a700 0x80>; + interrupt-parent = <&irq0_intc>; + interrupts = <0x6>; + brcm,gpio-bank-widths = <32 32 32 24>; + }; + + upg_gio_aon: gpio@f04172c0 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf04172c0 0x40>; + interrupt-parent = <&irq0_aon_intc>; + interrupts = <0x6>; + wakeup-source; + brcm,gpio-bank-widths = <18 4>; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt new file mode 100644 index 000000000..4a63bc96b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt @@ -0,0 +1,52 @@ +Broadcom Kona Family GPIO +========================= + +This GPIO driver is used in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 + +The Broadcom GPIO Controller IP can be configured prior to synthesis to +support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The +GPIO controller only supports edge, not level, triggering of interrupts. + +Required properties +------------------- + +- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends on the + number of GPIO banks on the SoC. The interrupts must be ordered by bank, + starting with bank 0. There is always a 1:1 mapping between banks and + IRQs. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second + cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) + See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type (bits[1:0]): + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 3 = low-to-high or high-to-low edge triggered + Valid values are 1, 2, 3 + See also .../devicetree/bindings/interrupt-controller/interrupts.txt. +- gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. + +Example: + gpio: gpio@35003000 { + compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x800>; + interrupts = + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml new file mode 100644 index 000000000..c213cb9dd --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,xgs-iproc-gpio.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/brcm,xgs-iproc-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom XGS iProc GPIO controller + +maintainers: + - Chris Packham <chris.packham@alliedtelesis.co.nz> + +description: | + This controller is the Chip Common A GPIO present on a number of Broadcom + switch ASICs with integrated SoCs. + +properties: + compatible: + const: brcm,iproc-gpio-cca + + reg: + items: + - description: the I/O address containing the GPIO controller registers. + - description: the I/O address containing the Chip Common A interrupt registers. + + gpio-controller: true + + '#gpio-cells': + const: 2 + + ngpios: + minimum: 0 + maximum: 32 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +dependencies: + interrupt-controller: [ interrupts ] + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + gpio@18000060 { + compatible = "brcm,iproc-gpio-cca"; + #gpio-cells = <2>; + reg = <0x18000060 0x50>, + <0x18000000 0x50>; + ngpios = <12>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + }; + + +... diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt new file mode 100644 index 000000000..9d6dcd3fe --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt @@ -0,0 +1,49 @@ +* General Purpose Input Output (GPIO) bus. + +Properties: +- compatible: "cavium,octeon-3860-gpio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the GPIO unit's register bank. + +- gpio-controller: This is a GPIO controller. + +- #gpio-cells: Must be <2>. The first cell is the GPIO pin. + +- interrupt-controller: The GPIO controller is also an interrupt + controller, many of its pins may be configured as an interrupt + source. + +- #interrupt-cells: Must be <2>. The first cell is the GPIO pin + connected to the interrupt source. The second cell is the interrupt + triggering protocol and may have one of four values: + 1 - edge triggered on the rising edge. + 2 - edge triggered on the falling edge + 4 - level triggered active high. + 8 - level triggered active low. + +- interrupts: Interrupt routing for each pin. + +Example: + + gpio-controller@1070000000800 { + #gpio-cells = <2>; + compatible = "cavium,octeon-3860-gpio"; + reg = <0x10700 0x00000800 0x0 0x100>; + gpio-controller; + /* Interrupts are specified by two parts: + * 1) GPIO pin number (0..15) + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + interrupt-controller; + #interrupt-cells = <2>; + /* The GPIO pin connect to 16 consecutive CUI bits */ + interrupts = <0 16>, <0 17>, <0 18>, <0 19>, + <0 20>, <0 21>, <0 22>, <0 23>, + <0 24>, <0 25>, <0 26>, <0 27>, + <0 28>, <0 29>, <0 30>, <0 31>; + }; diff --git a/Documentation/devicetree/bindings/gpio/cdns,gpio.txt b/Documentation/devicetree/bindings/gpio/cdns,gpio.txt new file mode 100644 index 000000000..706ef00f5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cdns,gpio.txt @@ -0,0 +1,43 @@ +Cadence GPIO controller bindings + +Required properties: +- compatible: should be "cdns,gpio-r1p02". +- reg: the register base address and size. +- #gpio-cells: should be 2. + * first cell is the GPIO number. + * second cell specifies the GPIO flags, as defined in + <dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH + and GPIO_ACTIVE_LOW flags are supported. +- gpio-controller: marks the device as a GPIO controller. +- clocks: should contain one entry referencing the peripheral clock driving + the GPIO controller. + +Optional properties: +- ngpios: integer number of gpio lines supported by this controller, up to 32. +- interrupts: interrupt specifier for the controllers interrupt. +- interrupt-controller: marks the device as an interrupt controller. When + defined, interrupts, interrupt-parent and #interrupt-cells + are required. +- interrupt-cells: should be 2. + * first cell is the GPIO number you want to use as an IRQ source. + * second cell specifies the IRQ type, as defined in + <dt-bindings/interrupt-controller/irq.h>. + Currently only level sensitive IRQs are supported. + + +Example: + gpio0: gpio-controller@fd060000 { + compatible = "cdns,gpio-r1p02"; + reg =<0xfd060000 0x1000>; + + clocks = <&gpio_clk>; + + interrupt-parent = <&gic>; + interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt new file mode 100644 index 000000000..fd42e7280 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -0,0 +1,17 @@ +* ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs + +Required properties: +- compatible: Should contain "cirrus,ep7209-mctrl-gpio". +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = Active high, + 1 = Active low. + +Example: + sysgpio: sysgpio { + compatible = "cirrus,ep7312-mctrl-gpio", + "cirrus,ep7209-mctrl-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/delta,tn48m-gpio.yaml b/Documentation/devicetree/bindings/gpio/delta,tn48m-gpio.yaml new file mode 100644 index 000000000..e3e668a12 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/delta,tn48m-gpio.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/delta,tn48m-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Delta Networks TN48M CPLD GPIO controller + +maintainers: + - Robert Marko <robert.marko@sartura.hr> + +description: | + This module is part of the Delta TN48M multi-function device. For more + details see ../mfd/delta,tn48m-cpld.yaml. + + Delta TN48M has an onboard Lattice CPLD that is used as an GPIO expander. + It provides 12 pins in total, they are input-only or ouput-only type. + +properties: + compatible: + enum: + - delta,tn48m-gpo + - delta,tn48m-gpi + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml b/Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml new file mode 100644 index 000000000..c0ad70e66 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/fairchild,74hc595.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic 8-bit shift register + +maintainers: + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + enum: + - fairchild,74hc595 + - nxp,74lvc594 + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + description: + The second cell is only used to specify the GPIO polarity. + const: 2 + + registers-number: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of daisy-chained shift registers + + enable-gpios: + description: GPIO connected to the OE (Output Enable) pin. + maxItems: 1 + +patternProperties: + "^(hog-[0-9]+|.+-hog(-[0-9]+)?)$": + type: object + + properties: + gpio-hog: true + gpios: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - registers-number + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + gpio5: gpio5@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <4>; + spi-max-frequency = <100000>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/faraday,ftgpio010.yaml b/Documentation/devicetree/bindings/gpio/faraday,ftgpio010.yaml new file mode 100644 index 000000000..640da5b9b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/faraday,ftgpio010.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/faraday,ftgpio010.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Faraday Technology FTGPIO010 GPIO Controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + compatible: + oneOf: + - items: + - const: cortina,gemini-gpio + - const: faraday,ftgpio010 + - items: + - const: moxa,moxart-gpio + - const: faraday,ftgpio010 + - const: faraday,ftgpio010 + + reg: + maxItems: 1 + + resets: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + description: Should contain the interrupt line for the GPIO block + + gpio-controller: true + "#gpio-cells": + const: 2 + + interrupt-controller: true + "#interrupt-cells": + const: 2 + +required: + - compatible + - reg + - interrupts + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + gpio@4d000000 { + compatible = "cortina,gemini-gpio", "faraday,ftgpio010"; + reg = <0x4d000000 0x100>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/fsl,imx8qxp-sc-gpio.yaml b/Documentation/devicetree/bindings/gpio/fsl,imx8qxp-sc-gpio.yaml new file mode 100644 index 000000000..b7b322209 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fsl,imx8qxp-sc-gpio.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/fsl,imx8qxp-sc-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO driver over IMX SCU firmware API + +maintainers: + - Shenwei Wang <shenwei.wang@nxp.com> + +description: | + This module provides the standard interface to control the + resource pins in SCU domain on i.MX8 platforms. + +properties: + compatible: + enum: + - fsl,imx8qxp-sc-gpio + + "#gpio-cells": + const: 2 + + gpio-controller: true + +required: + - compatible + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + gpio0: gpio { + compatible = "fsl,imx8qxp-sc-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.yaml b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.yaml new file mode 100644 index 000000000..ae1860369 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX/MXC GPIO controller + +maintainers: + - Anson Huang <Anson.Huang@nxp.com> + +properties: + compatible: + oneOf: + - enum: + - fsl,imx1-gpio + - fsl,imx21-gpio + - fsl,imx31-gpio + - fsl,imx35-gpio + - fsl,imx7d-gpio + - items: + - const: fsl,imx35-gpio + - const: fsl,imx31-gpio + - items: + - enum: + - fsl,imx50-gpio + - fsl,imx51-gpio + - fsl,imx53-gpio + - fsl,imx6q-gpio + - fsl,imx6sl-gpio + - fsl,imx6sll-gpio + - fsl,imx6sx-gpio + - fsl,imx6ul-gpio + - fsl,imx7d-gpio + - fsl,imx8mm-gpio + - fsl,imx8mn-gpio + - fsl,imx8mp-gpio + - fsl,imx8mq-gpio + - fsl,imx8qxp-gpio + - fsl,imxrt1050-gpio + - fsl,imxrt1170-gpio + - const: fsl,imx35-gpio + + reg: + maxItems: 1 + + interrupts: + description: | + Should be the port interrupt shared by all 32 pins, if one number. + If two numbers, the first one is the interrupt shared by low 16 pins + and the second one is for high 16 pins. + minItems: 1 + maxItems: 2 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + gpio-line-names: true + gpio-ranges: true + + power-domains: + maxItems: 1 + +patternProperties: + "^(hog-[0-9]+|.+-hog(-[0-9]+)?)$": + type: object + properties: + gpio-hog: true + gpios: true + input: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + gpio0: gpio@73f84000 { + compatible = "fsl,imx35-gpio"; + reg = <0x73f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt b/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt new file mode 100644 index 000000000..bef353f37 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt @@ -0,0 +1,20 @@ +Fujitsu MB86S7x GPIO Controller +------------------------------- + +Required properties: +- compatible: Should be "fujitsu,mb86s70-gpio" +- reg: Base address and length of register space +- clocks: Specify the clock +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). + +Examples: + gpio0: gpio@31000000 { + compatible = "fujitsu,mb86s70-gpio"; + reg = <0 0x31000000 0x10000>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&clk 0 2 1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt new file mode 100644 index 000000000..6e81f8b75 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt @@ -0,0 +1,20 @@ +Gateworks PLD GPIO controller bindings + +The GPIO controller should be a child node on an I2C bus, +see: i2c/i2c.txt for details. + +Required properties: +- compatible: Should be "gateworks,pld-gpio" +- reg: I2C slave address +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and + the second cell is used to specify optional parameters. + +Example: + +pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt b/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt new file mode 100644 index 000000000..7bb1a9d60 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt @@ -0,0 +1,30 @@ +* 74XX MMIO GPIO driver + +Required properties: +- compatible: Should contain one of the following: + "ti,741g125": for 741G125 (1-bit Input), + "ti,741g174": for 741G74 (1-bit Output), + "ti,742g125": for 742G125 (2-bit Input), + "ti,7474" : for 7474 (2-bit Output), + "ti,74125" : for 74125 (4-bit Input), + "ti,74175" : for 74175 (4-bit Output), + "ti,74365" : for 74365 (6-bit Input), + "ti,74174" : for 74174 (6-bit Output), + "ti,74244" : for 74244 (8-bit Input), + "ti,74273" : for 74273 (8-bit Output), + "ti,741624" : for 741624 (16-bit Input), + "ti,7416374": for 7416374 (16-bit Output). +- reg: Physical base address and length where IC resides. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the GPIO polarity: + 0 = Active High, + 1 = Active Low. + +Example: + ctrl: gpio@30008004 { + compatible = "ti,74174"; + reg = <0x30008004 0x1>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt new file mode 100644 index 000000000..a28902a65 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt @@ -0,0 +1,33 @@ +Avionic Design N-bit GPIO expander bindings + +Required properties: +- compatible: should be "ad,gpio-adnp" +- reg: The I2C slave address for this device. +- interrupts: Interrupt specifier for the controllers interrupt. +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + - bit 0: polarity (0: normal, 1: inverted) +- gpio-controller: Marks the device as a GPIO controller +- nr-gpios: The number of pins supported by the controller. + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier as described in +Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + +Example: + + gpioext: gpio-controller@41 { + compatible = "ad,gpio-adnp"; + reg = <0x41>; + + interrupt-parent = <&gpio>; + interrupts = <160 1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + nr-gpios = <64>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt new file mode 100644 index 000000000..2a80e272c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -0,0 +1,44 @@ +Altera GPIO controller bindings + +Required properties: +- compatible: + - "altr,pio-1.0" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells : Should be 2 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller +- #interrupt-cells : Should be 2. The interrupt type is fixed in the hardware. + - The first cell is the GPIO offset number within the GPIO controller. + - The second cell is the interrupt trigger type and level flags. +- interrupts: Specify the interrupt. +- altr,interrupt-type: Specifies the interrupt trigger type the GPIO + hardware is synthesized. This field is required if the Altera GPIO controller + used has IRQ enabled as the interrupt type is not software controlled, + but hardware synthesized. Required if GPIO is used as an interrupt + controller. The value is defined in <dt-bindings/interrupt-controller/irq.h> + Only the following flags are supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + +Optional properties: +- altr,ngpio: Width of the GPIO bank. This defines how many pins the + GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not + specified. + +Example: + +gpio_altr: gpio@ff200000 { + compatible = "altr,pio-1.0"; + reg = <0xff200000 0x10>; + interrupts = <0 45 4>; + altr,ngpio = <32>; + altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt new file mode 100644 index 000000000..b2033fc3a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt @@ -0,0 +1,39 @@ +Aspeed GPIO controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Either "aspeed,ast2400-gpio", "aspeed,ast2500-gpio", + or "aspeed,ast2600-gpio". + +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify optional + parameters (unused) + +- reg : Address and length of the register set for the device +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt specifier (see interrupt bindings for + details) +- interrupt-controller : Mark the GPIO controller as an interrupt-controller + +Optional properties: + +- clocks : A phandle to the clock to use for debounce timings +- ngpios : Number of GPIOs controlled by this controller. Should be set + when there are multiple GPIO controllers on a SoC (ast2600). + +The gpio and interrupt properties are further described in their respective +bindings documentation: + +- Documentation/devicetree/bindings/gpio/gpio.txt +- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + + Example: + gpio@1e780000 { + #gpio-cells = <2>; + compatible = "aspeed,ast2400-gpio"; + gpio-controller; + interrupts = <20>; + reg = <0x1e780000 0x1000>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ath79.txt b/Documentation/devicetree/bindings/gpio/gpio-ath79.txt new file mode 100644 index 000000000..cf71f3ec9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ath79.txt @@ -0,0 +1,37 @@ +Binding for Qualcomm Atheros AR7xxx/AR9xxx GPIO controller + +Required properties: +- compatible: has to be "qca,<soctype>-gpio" and one of the following + fallbacks: + - "qca,ar7100-gpio" + - "qca,ar9340-gpio" +- reg: Base address and size of the controllers memory area +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters. +- ngpios: Should be set to the number of GPIOs available on the SoC. + +Optional properties: +- interrupts: Interrupt specifier for the controllers interrupt. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode interrupt + source, should be 2 + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +Example: + + gpio@18040000 { + compatible = "qca,ar9132-gpio", "qca,ar7100-gpio"; + reg = <0x18040000 0x30>; + interrupts = <2>; + + ngpios = <22>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt new file mode 100644 index 000000000..0a304ad29 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -0,0 +1,28 @@ +Cirrus Logic CLPS711X GPIO controller + +Required properties: +- compatible: Should be "cirrus,ep7209-gpio" +- reg: Physical base GPIO controller registers location and length. + There should be two registers, first is DATA register, the second + is DIRECTION. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + gpio0 = &porta; +}; + +porta: gpio@80000000 { + compatible = "cirrus,ep7312-gpio","cirrus,ep7209-gpio"; + reg = <0x80000000 0x1>, <0x80000040 0x1>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-consumer-common.yaml b/Documentation/devicetree/bindings/gpio/gpio-consumer-common.yaml new file mode 100644 index 000000000..40d0be31e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-consumer-common.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-consumer-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common GPIO lines + +maintainers: + - Bartosz Golaszewski <brgl@bgdev.pl> + - Linus Walleij <linus.walleij@linaro.org> + +description: + Pay attention to using proper GPIO flag (e.g. GPIO_ACTIVE_LOW) for the GPIOs + using inverted signal (e.g. RESETN). + +select: true + +properties: + enable-gpios: + maxItems: 1 + description: + GPIO connected to the enable control pin. + + reset-gpios: + description: + GPIO (or GPIOs for power sequence) connected to the device reset pin + (e.g. RESET or RESETN). + + powerdown-gpios: + maxItems: 1 + description: + GPIO connected to the power down pin (hardware power down or power cut, + e.g. PD or PWDN). + + pwdn-gpios: + maxItems: 1 + description: Use powerdown-gpios + deprecated: true + + wakeup-gpios: + maxItems: 1 + description: + GPIO connected to the pin waking up the device from suspend or other + power-saving modes. + +allOf: + - if: + properties: + compatible: + contains: + enum: + - mmc-pwrseq-simple + then: + properties: + reset-gpios: + minItems: 1 + maxItems: 32 + else: + properties: + reset-gpios: + maxItems: 1 + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/gpio/gpio-davinci.yaml b/Documentation/devicetree/bindings/gpio/gpio-davinci.yaml new file mode 100644 index 000000000..f32e09ef9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-davinci.yaml @@ -0,0 +1,185 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-davinci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controller for Davinci and keystone devices + +maintainers: + - Keerthy <j-keerthy@ti.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - ti,k2g-gpio + - ti,am654-gpio + - ti,j721e-gpio + - ti,am64-gpio + - const: ti,keystone-gpio + + - items: + - enum: + - ti,dm6441-gpio + - ti,keystone-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + gpio-ranges: true + + gpio-line-names: + description: strings describing the names of each gpio line. + minItems: 1 + maxItems: 100 + + "#gpio-cells": + const: 2 + description: + first cell is the pin number and second cell is used to specify optional parameters (unused). + + interrupts: + description: + The interrupts are specified as per the interrupt parent. Only banked + or unbanked IRQs are supported at a time. If the interrupts are + banked then provide list of interrupts corresponding to each bank, else + provide the list of interrupts for each gpio. + minItems: 1 + maxItems: 100 + + ti,ngpio: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The number of GPIO pins supported consecutively. + minimum: 1 + + ti,davinci-gpio-unbanked: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The number of GPIOs that have an individual interrupt line to processor. + minimum: 0 + + clocks: + maxItems: 1 + + clock-names: + const: gpio + + interrupt-controller: true + + power-domains: + maxItems: 1 + + "#interrupt-cells": + const: 2 + +patternProperties: + "^(.+-hog(-[0-9]+)?)$": + type: object + + required: + - gpio-hog + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - interrupts + - ti,ngpio + - ti,davinci-gpio-unbanked + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include<dt-bindings/interrupt-controller/arm-gic.h> + + gpio0: gpio@2603000 { + compatible = "ti,k2g-gpio", "ti,keystone-gpio"; + reg = <0x02603000 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 433 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 434 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 436 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 437 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 438 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 439 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 440 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <144>; + ti,davinci-gpio-unbanked = <0>; + clocks = <&k2g_clks 0x001b 0x0>; + clock-names = "gpio"; + }; + + - | + #include<dt-bindings/interrupt-controller/arm-gic.h> + + gpio1: gpio@260bf00 { + compatible = "ti,keystone-gpio"; + reg = <0x0260bf00 0x100>; + gpio-controller; + #gpio-cells = <2>; + /* HW Interrupts mapped to GPIO pins */ + interrupts = <GIC_SPI 120 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 121 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 123 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 124 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 147 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkgpio>; + clock-names = "gpio"; + ti,ngpio = <32>; + ti,davinci-gpio-unbanked = <32>; + }; + + - | + wkup_gpio0: gpio0@42110000 { + compatible = "ti,am654-gpio", "ti,keystone-gpio"; + reg = <0x42110000 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&intr_wkup_gpio>; + interrupts = <60>, <61>, <62>, <63>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <56>; + ti,davinci-gpio-unbanked = <0>; + clocks = <&k3_clks 59 0>; + clock-names = "gpio"; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt new file mode 100644 index 000000000..0423699d7 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt @@ -0,0 +1,39 @@ +Keystone 2 DSP GPIO controller bindings + +HOST OS userland running on ARM can send interrupts to DSP cores using +the DSP GPIO controller IP. It provides 28 IRQ signals per each DSP core. +This is one of the component used by the IPC mechanism used on Keystone SOCs. + +For example TCI6638K2K SoC has 8 DSP GPIO controllers: + - 8 for C66x CorePacx CPUs 0-7 + +Keystone 2 DSP GPIO controller has specific features: +- each GPIO can be configured only as output pin; +- setting GPIO value to 1 causes IRQ generation on target DSP core; +- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still + pending. + +Required Properties: +- compatible: should be "ti,keystone-dsp-gpio" +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset of device's specific + registers within device state control registers range. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be 2. + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: + dspgpio0: keystone_dsp_gpio@2620240 { + compatible = "ti,keystone-dsp-gpio"; + ti,syscon-dev = <&devctrl 0x240>; + gpio-controller; + #gpio-cells = <2>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + kick-gpio = <&dspgpio0 27>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt new file mode 100644 index 000000000..54040a2bf --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt @@ -0,0 +1,97 @@ +Spreadtrum EIC controller bindings + +The EIC is the abbreviation of external interrupt controller, which can +be used only in input mode. The Spreadtrum platform has 2 EIC controllers, +one is in digital chip, and another one is in PMIC. The digital chip EIC +controller contains 4 sub-modules: EIC-debounce, EIC-latch, EIC-async and +EIC-sync. But the PMIC EIC controller contains only one EIC-debounce sub- +module. + +The EIC-debounce sub-module provides up to 8 source input signal +connections. A debounce mechanism is used to capture the input signals' +stable status (millisecond resolution) and a single-trigger mechanism +is introduced into this sub-module to enhance the input event detection +reliability. In addition, this sub-module's clock can be shut off +automatically to reduce power dissipation. Moreover the debounce range +is from 1ms to 4s with a step size of 1ms. The input signal will be +ignored if it is asserted for less than 1 ms. + +The EIC-latch sub-module is used to latch some special power down signals +and generate interrupts, since the EIC-latch does not depend on the APB +clock to capture signals. + +The EIC-async sub-module uses a 32kHz clock to capture the short signals +(microsecond resolution) to generate interrupts by level or edge trigger. + +The EIC-sync is similar with GPIO's input function, which is a synchronized +signal input register. It can generate interrupts by level or edge trigger +when detecting input signals. + +Required properties: +- compatible: Should be one of the following: + "sprd,sc9860-eic-debounce", + "sprd,sc9860-eic-latch", + "sprd,sc9860-eic-async", + "sprd,sc9860-eic-sync", + "sprd,sc2731-eic". +- reg: Define the base and range of the I/O address space containing + the GPIO controller registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and + the second cell is used to specify optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be <2>. Specifies the number of cells needed + to encode interrupt source. +- interrupts: Should be the port interrupt shared by all the gpios. + +Example: + eic_debounce: gpio@40210000 { + compatible = "sprd,sc9860-eic-debounce"; + reg = <0 0x40210000 0 0x80>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + }; + + eic_latch: gpio@40210080 { + compatible = "sprd,sc9860-eic-latch"; + reg = <0 0x40210080 0 0x20>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + }; + + eic_async: gpio@402100a0 { + compatible = "sprd,sc9860-eic-async"; + reg = <0 0x402100a0 0 0x20>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + }; + + eic_sync: gpio@402100c0 { + compatible = "sprd,sc9860-eic-sync"; + reg = <0 0x402100c0 0 0x20>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + }; + + pmic_eic: gpio@300 { + compatible = "sprd,sc2731-eic"; + reg = <0x300>; + interrupt-parent = <&sc2731_pmic>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-exar.txt b/Documentation/devicetree/bindings/gpio/gpio-exar.txt new file mode 100644 index 000000000..4540d6182 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-exar.txt @@ -0,0 +1,5 @@ +Exportable MPIO interface of Exar UART chips + +Required properties of the device: + - exar,first-pin: first exportable pins (0..15) + - ngpios: number of exportable pins (1..16) diff --git a/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt new file mode 100644 index 000000000..e46659810 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt @@ -0,0 +1,26 @@ +Aeroflex Gaisler GRGPIO General Purpose I/O cores. + +The GRGPIO GPIO core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system, +these properties are built from information in the AMBA plug&play. + +Required properties: + +- name : Should be "GAISLER_GPIO" or "01_01a" + +- reg : Address and length of the register set for the device + +- interrupts : Interrupt numbers for this device + +Optional properties: + +- nbits : The number of gpio lines. If not present driver assumes 32 lines. + +- irqmap : An array with an index for each gpio line. An index is either a valid + index into the interrupts property array, or 0xffffffff that indicates + no irq for that line. Driver provides no interrupt support if not + present. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt b/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt new file mode 100644 index 000000000..80fcb7d70 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt @@ -0,0 +1,37 @@ +TI/National Semiconductor LP3943 GPIO controller + +Required properties: + - compatible: "ti,lp3943-gpio" + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. See gpio.txt in this directory for a + description of the cells format. + +Example: +Simple LED controls with LP3943 GPIO controller + +&i2c4 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + gpioex: gpio { + compatible = "ti,lp3943-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; +}; + +leds { + compatible = "gpio-leds"; + indicator1 { + label = "indi1"; + gpios = <&gpioex 9 GPIO_ACTIVE_LOW>; + }; + + indicator2 { + label = "indi2"; + gpios = <&gpioex 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt new file mode 100644 index 000000000..b3a6444b8 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt @@ -0,0 +1,59 @@ +GPIO driver for Maxim MAX3191x industrial serializer + +Required properties: + - compatible: Must be one of: + "maxim,max31910" + "maxim,max31911" + "maxim,max31912" + "maxim,max31913" + "maxim,max31953" + "maxim,max31963" + - reg: Chip select number. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be two. For consumer use see gpio.txt. + +Optional properties: + - #daisy-chained-devices: + Number of chips in the daisy-chain (default is 1). + - maxim,modesel-gpios: GPIO pins to configure modesel of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + (if each chip is driven by a separate pin) or 1 + (if all chips are wired to the same pin). + - maxim,fault-gpios: GPIO pins to read fault of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db0-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db1-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "maxim,db0-gpios". + - maxim,modesel-8bit: Boolean whether the modesel pin of the chips is + pulled high (8-bit mode). Use this if the modesel pin + is hardwired and consequently "maxim,modesel-gpios" + cannot be specified. By default if neither this nor + "maxim,modesel-gpios" is given, the driver assumes + that modesel is pulled low (16-bit mode). + - maxim,ignore-undervoltage: + Boolean whether to ignore undervoltage alarms signaled + by the "maxim,fault-gpios" or by the status byte + (in 16-bit mode). Use this if the chips are powered + through 5VOUT instead of VCC24V, in which case they + will constantly signal undervoltage. + +For other required and optional properties of SPI slave nodes please refer to +../spi/spi-bus.txt. + +Example: + gpio@0 { + compatible = "maxim,max31913"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + + maxim,modesel-gpios = <&gpio2 23>; + maxim,fault-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; + maxim,db0-gpios = <&gpio2 25>; + maxim,db1-gpios = <&gpio2 26>; + + spi-max-frequency = <25000000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max77620.txt b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt new file mode 100644 index 000000000..410e716fd --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt @@ -0,0 +1,25 @@ +GPIO driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Required properties: +------------------- +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +For more details, please refer generic GPIO DT binding document +<devicetree/bindings/gpio/gpio.txt>. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + compatible = "maxim,max77620"; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt new file mode 100644 index 000000000..f93d51478 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt @@ -0,0 +1,38 @@ +Lantiq SoC External Bus memory mapped GPIO controller + +By attaching hardware latches to the EBU it is possible to create output +only gpios. This driver configures a special memory address, which when +written to outputs 16 bit to the latches. + +The node describing the memory mapped GPIOs needs to be a child of the node +describing the "lantiq,localbus". + +Required properties: +- compatible : Should be "lantiq,gpio-mm-lantiq" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. + +Example: + +localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + + gpio_mm0: gpio@4000000 { + compatible = "lantiq,gpio-mm"; + reg = <1 0x0 0x10>; + gpio-controller; + #gpio-cells = <2>; + lantiq,shadow = <0x77f> + }; +} diff --git a/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt new file mode 100644 index 000000000..410759de9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt @@ -0,0 +1,18 @@ +Turris Mox Moxtet GPIO expander via Moxtet bus + +Required properties: + - compatible : Should be "cznic,moxtet-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Other properties are required for a Moxtet bus device, please refer to +Documentation/devicetree/bindings/bus/moxtet.txt. + +Example: + + moxtet_sfp: gpio@0 { + compatible = "cznic,moxtet-gpio"; + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + } diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt new file mode 100644 index 000000000..cd28e932b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -0,0 +1,53 @@ +* Freescale MPC512x/MPC8xxx/QorIQ/Layerscape GPIO controller + +Required properties: +- compatible : Should be "fsl,<soc>-gpio" + The following <soc>s are known to be supported: + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq, + ls1021a, ls1043a, ls2080a, ls1028a, ls1088a. +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Optional properties: +- little-endian : GPIO registers are used as little endian. If not + present registers are used as big endian by default. + +Example of gpio-controller node for a mpc5125 SoC: + +gpio0: gpio@1100 { + compatible = "fsl,mpc5125-gpio"; + #gpio-cells = <2>; + reg = <0x1100 0x080>; + interrupts = <78 0x8>; +}; + +Example of gpio-controller node for a ls2080a SoC: + +gpio0: gpio@2300000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; + + +Example of gpio-controller node for a ls1028a/ls1088a SoC: + +gpio1: gpio@2300000 { + compatible = "fsl,ls1028a-gpio", "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + little-endian; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml b/Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml new file mode 100644 index 000000000..f1bd1e6b2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.yaml @@ -0,0 +1,146 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell EBU GPIO controller + +maintainers: + - Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + - Andrew Lunn <andrew@lunn.ch> + +properties: + compatible: + oneOf: + - enum: + - marvell,armada-8k-gpio + - marvell,orion-gpio + + - items: + - enum: + - marvell,mv78200-gpio + - marvell,armada-370-gpio + - const: marvell,orion-gpio + + - description: Deprecated binding + items: + - const: marvell,armadaxp-gpio + - const: marvell,orion-gpio + deprecated: true + + reg: + description: | + Address and length of the register set for the device. Not used for + marvell,armada-8k-gpio. + + A second entry can be provided, for the PWM function using the GPIO Blink + Counter on/off registers. + minItems: 1 + maxItems: 2 + + reg-names: + items: + - const: gpio + - const: pwm + minItems: 1 + + offset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Offset in the register map for the gpio registers (in bytes) + + interrupts: + description: | + The list of interrupts that are used for all the pins managed by this + GPIO bank. There can be more than one interrupt (example: 1 interrupt + per 8 pins on Armada XP, which means 4 interrupts per bank of 32 + GPIOs). + minItems: 1 + maxItems: 4 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + gpio-controller: true + + ngpios: + minimum: 1 + maximum: 32 + + "#gpio-cells": + const: 2 + + marvell,pwm-offset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Offset in the register map for the pwm registers (in bytes) + + "#pwm-cells": + description: + The first cell is the GPIO line number. The second cell is the period + in nanoseconds. + const: 2 + + clocks: + description: + Clock(s) used for PWM function. + items: + - description: Core clock + - description: AXI bus clock + minItems: 1 + + clock-names: + items: + - const: core + - const: axi + minItems: 1 + +required: + - compatible + - gpio-controller + - ngpios + - "#gpio-cells" + +allOf: + - if: + properties: + compatible: + contains: + const: marvell,armada-8k-gpio + then: + required: + - offset + else: + required: + - reg + +unevaluatedProperties: true + +examples: + - | + gpio@d0018100 { + compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio"; + reg = <0xd0018100 0x40>, <0xd0018800 0x30>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <16>, <17>, <18>, <19>; + }; + + - | + gpio@18140 { + compatible = "marvell,armada-370-gpio", "marvell,orion-gpio"; + reg = <0x18140 0x40>, <0x181c8 0x08>; + reg-names = "gpio", "pwm"; + ngpios = <17>; + gpio-controller; + #gpio-cells = <2>; + #pwm-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <87>, <88>, <89>; + clocks = <&coreclk 0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml b/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml new file mode 100644 index 000000000..dfa1133f8 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.yaml @@ -0,0 +1,136 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS GPIO controller + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + - Anson Huang <Anson.Huang@nxp.com> + +description: | + The Freescale MXS GPIO controller is part of MXS PIN controller. + The GPIOs are organized in port/bank, each port consists of 32 GPIOs. + As the GPIO controller is embedded in the PIN controller and all the + GPIO ports share the same IO space with PIN controller, the GPIO node + will be represented as sub-nodes of MXS pinctrl node. + +properties: + compatible: + enum: + - fsl,imx23-pinctrl + - fsl,imx28-pinctrl + + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + reg: + maxItems: 1 + +patternProperties: + "gpio@[0-9]+$": + type: object + properties: + compatible: + enum: + - fsl,imx23-gpio + - fsl,imx28-gpio + + reg: + maxItems: 1 + + interrupts: + description: Should be the port interrupt shared by all 32 pins. + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + "#gpio-cells": + const: 2 + + gpio-controller: true + + required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - "#gpio-cells" + - gpio-controller + + additionalProperties: false + +required: + - compatible + - reg + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + pinctrl@80018000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-pinctrl"; + reg = <0x80018000 0x2000>; + + gpio@0 { + compatible = "fsl,imx28-gpio"; + reg = <0>; + interrupts = <127>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@1 { + compatible = "fsl,imx28-gpio"; + reg = <1>; + interrupts = <126>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@2 { + compatible = "fsl,imx28-gpio"; + reg = <2>; + interrupts = <125>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@3 { + compatible = "fsl,imx28-gpio"; + reg = <3>; + interrupts = <124>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@4 { + compatible = "fsl,imx28-gpio"; + reg = <4>; + interrupts = <123>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt new file mode 100644 index 000000000..8315ac778 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt @@ -0,0 +1,31 @@ +Nomadik GPIO controller + +Required properties: +- compatible : Should be "st,nomadik-gpio". +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. +- #gpio-cells : Should be two: + The first cell is the pin number. + The second cell is used to specify optional parameters: + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller : Marks the device node as an interrupt controller. +- gpio-bank : Specifies which bank a controller owns. +- st,supports-sleepmode : Specifies whether controller can sleep or not + +Example: + + gpio1: gpio@8012e080 { + compatible = "st,nomadik-gpio"; + reg = <0x8012e080 0x80>; + interrupts = <0 120 0x4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + st,supports-sleepmode; + gpio-bank = <1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-palmas.txt b/Documentation/devicetree/bindings/gpio/gpio-palmas.txt new file mode 100644 index 000000000..08b5b52a3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-palmas.txt @@ -0,0 +1,27 @@ +Palmas GPIO controller bindings + +Required properties: +- compatible: + - "ti,palams-gpio" for palma series of the GPIO controller + - "ti,tps80036-gpio" for Palma series device TPS80036. + - "ti,tps65913-gpio" for palma series device TPS65913. + - "ti,tps65914-gpio" for palma series device TPS65914. +- #gpio-cells : Should be two. + - first cell is the gpio pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller : Marks the device node as a GPIO controller. + +Note: This gpio node will be sub node of palmas node. + +Example: + palmas: tps65913@58 { + ::::::::::: + palmas_gpio: palmas_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + ::::::::::: + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca9570.yaml b/Documentation/devicetree/bindings/gpio/gpio-pca9570.yaml new file mode 100644 index 000000000..1acaa0a3d --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pca9570.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-pca9570.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PCA9570 I2C GPO expander + +maintainers: + - Sungbo Eo <mans0n@gorani.run> + +properties: + compatible: + enum: + - nxp,pca9570 + - nxp,pca9571 + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + gpio@24 { + compatible = "nxp,pca9570"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml b/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml new file mode 100644 index 000000000..1b70e9f30 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml @@ -0,0 +1,235 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP PCA95xx I2C GPIO multiplexer + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |+ + Bindings for the family of I2C GPIO multiplexers/expanders: NXP PCA95xx, + Maxim MAX73xx + +properties: + compatible: + oneOf: + - items: + - const: diodes,pi4ioe5v6534q + - const: nxp,pcal6534 + - items: + - enum: + - exar,xra1202 + - maxim,max7310 + - maxim,max7312 + - maxim,max7313 + - maxim,max7315 + - maxim,max7319 + - maxim,max7320 + - maxim,max7321 + - maxim,max7322 + - maxim,max7323 + - maxim,max7324 + - maxim,max7325 + - maxim,max7326 + - maxim,max7327 + - nxp,pca6408 + - nxp,pca6416 + - nxp,pca9505 + - nxp,pca9506 + - nxp,pca9534 + - nxp,pca9535 + - nxp,pca9536 + - nxp,pca9537 + - nxp,pca9538 + - nxp,pca9539 + - nxp,pca9554 + - nxp,pca9555 + - nxp,pca9556 + - nxp,pca9557 + - nxp,pca9574 + - nxp,pca9575 + - nxp,pca9698 + - nxp,pcal6408 + - nxp,pcal6416 + - nxp,pcal6524 + - nxp,pcal6534 + - nxp,pcal9535 + - nxp,pcal9554b + - nxp,pcal9555a + - onnn,cat9554 + - onnn,pca9654 + - ti,pca6107 + - ti,pca9536 + - ti,tca6408 + - ti,tca6416 + - ti,tca6424 + - ti,tca9539 + - ti,tca9554 + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-line-names: + minItems: 1 + maxItems: 40 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + reset-gpios: + maxItems: 1 + description: + GPIO specification for the RESET input. This is an active low signal to + the PCA953x. Not valid for Maxim MAX732x devices. + + vcc-supply: + description: + Optional power supply. Not valid for Maxim MAX732x devices. + + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + +patternProperties: + "^(hog-[0-9]+|.+-hog(-[0-9]+)?)$": + type: object + properties: + gpio-hog: true + gpios: true + input: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - maxim,max7320 + - maxim,max7321 + - maxim,max7322 + - maxim,max7323 + - maxim,max7324 + - maxim,max7325 + - maxim,max7326 + - maxim,max7327 + then: + properties: + reset-gpios: false + vcc-supply: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + gpio@20 { + compatible = "nxp,pca9505"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9505>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + + usb3-sata-sel-hog { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "usb3_sata_sel"; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c1 { + #address-cells = <1>; + #size-cells = <0>; + + gpio99: gpio@22 { + compatible = "nxp,pcal6524"; + reg = <0x22>; + interrupt-parent = <&gpio6>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* gpio6_161 */ + interrupt-controller; + #interrupt-cells = <2>; + vcc-supply = <&vdds_1v8_main>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", + "vibra", "fault2", "p06", "p07", "en-usb", + "en-host1", "en-host2", "chg-int", "p14", "p15", + "mic-int", "en-modem", "shdn-hs-amp", + "chg-status+red", "green", "blue", "en-esata", + "fault1", "p26", "p27"; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c2 { + #address-cells = <1>; + #size-cells = <0>; + + /* MAX7325 with interrupt support enabled */ + gpio@6d { + compatible = "maxim,max7325"; + reg = <0x6d>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + }; + }; + + - | + i2c3 { + #address-cells = <1>; + #size-cells = <0>; + + /* MAX7325 with interrupt support disabled */ + gpio@6e { + compatible = "maxim,max7325"; + reg = <0x6e>; + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt new file mode 100644 index 000000000..fba3c61f6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt @@ -0,0 +1,34 @@ +Generic Parallel-in/Serial-out Shift Register GPIO Driver + +This binding describes generic parallel-in/serial-out shift register +devices that can be used for GPI (General Purpose Input). This includes +SN74165 serial-out shift registers and the SN65HVS88x series of +industrial serializers. + +Required properties: + - compatible : Should be "pisosr-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Optional properties: + - ngpios : Number of used GPIO lines (0..n-1), default is 8. + - load-gpios : GPIO pin specifier attached to load enable, this + pin is pulsed before reading from the device to + load input pin values into the device. + +For other required and optional properties of SPI slave +nodes please refer to ../spi/spi-bus.txt. + +Example: + + gpio@0 { + compatible = "ti,sn65hvs882", "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-rda.yaml b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml new file mode 100644 index 000000000..6ece555f0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-rda.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-rda.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RDA Micro GPIO controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + const: rda,8810pl-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + ngpios: + description: + Number of available gpios in a bank. + minimum: 1 + maximum: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - ngpios + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/gpio/gpio-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-sprd.txt new file mode 100644 index 000000000..eca97d453 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-sprd.txt @@ -0,0 +1,28 @@ +Spreadtrum GPIO controller bindings + +The controller's registers are organized as sets of sixteen 16-bit +registers with each set controlling a bank of up to 16 pins. A single +interrupt is shared for all of the banks handled by the controller. + +Required properties: +- compatible: Should be "sprd,sc9860-gpio". +- reg: Define the base and range of the I/O address space containing +the GPIO controller registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and +the second cell is used to specify optional parameters. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be <2>. Specifies the number of cells needed +to encode interrupt source. +- interrupts: Should be the port interrupt shared by all the gpios. + +Example: + ap_gpio: gpio@40280000 { + compatible = "sprd,sc9860-gpio"; + reg = <0 0x40280000 0 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt new file mode 100644 index 000000000..b33f8f02c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt @@ -0,0 +1,17 @@ +STMPE gpio +---------- + +Required properties: + - compatible: "st,stmpe-gpio" + +Optional properties: + - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable + due to different usage (e.g. touch, keypad) + +Node should be child node of stmpe node to which it belongs. + +Example: + stmpe_gpio { + compatible = "st,stmpe-gpio"; + st,norequest-mask = <0x20>; //gpio 5 can't be used + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml new file mode 100644 index 000000000..d565c4b63 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lantiq SoC Serial To Parallel (STP) GPIO controller + +description: | + The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a + peripheral controller used to drive external shift register cascades. At most + 3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem + and Ethernet PHYs to drive some bytes of the cascade automatically. + +maintainers: + - John Crispin <john@phrozen.org> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: lantiq,gpio-stp-xway + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + description: + The first cell is the pin number and the second cell is used to specify + consumer flags. + const: 2 + + lantiq,shadow: + description: + The default value that we shall assume as already set on the + shift register cascade. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x000000 + maximum: 0xffffff + + lantiq,groups: + description: + Set the 3 bit mask to select which of the 3 groups are enabled + in the shift register cascade. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x7 + + lantiq,dsl: + description: + The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit + property can enable this feature. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x3 + + lantiq,rising: + description: + Use rising instead of falling edge for the shift register. + type: boolean + +patternProperties: + "^lantiq,phy[1-4]$": + description: + The gphy core can control 3 bits of the gpio cascade. In the xRX200 family + phy[1-2] are available, in xRX330 phy[1-3] and in XRX330 phy[1-4]. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x7 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + gpio@e100bb0 { + compatible = "lantiq,gpio-stp-xway"; + reg = <0xE100BB0 0x40>; + #gpio-cells = <2>; + gpio-controller; + + pinctrl-0 = <&stp_pins>; + pinctrl-names = "default"; + + lantiq,shadow = <0xffffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x3>; + lantiq,phy1 = <0x7>; + lantiq,phy2 = <0x7>; + }; +... diff --git a/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt b/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt new file mode 100644 index 000000000..3f883ae29 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt @@ -0,0 +1,27 @@ +Cavium ThunderX/OCTEON-TX GPIO controller bindings + +Required Properties: +- reg: The controller bus address. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Must be 2. + - First cell is the GPIO pin number relative to the controller. + - Second cell is a standard generic flag bitfield as described in gpio.txt. + +Optional Properties: +- compatible: "cavium,thunder-8890-gpio", unused as PCI driver binding is used. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Must be present and have value of 2 if + "interrupt-controller" is present. + - First cell is the GPIO pin number relative to the controller. + - Second cell is triggering flags as defined in interrupts.txt. + +Example: + +gpio_6_0: gpio@6,0 { + compatible = "cavium,thunder-8890-gpio"; + reg = <0x3000 0 0 0 0>; /* DEVFN = 0x30 (6:0) */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-tpic2810.yaml b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.yaml new file mode 100644 index 000000000..cb8a5c376 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-tpic2810.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-tpic2810.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TPIC2810 GPIO controller bindings + +maintainers: + - Aswath Govindraju <a-govindraju@ti.com> + +properties: + compatible: + enum: + - ti,tpic2810 + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-line-names: + minItems: 1 + maxItems: 32 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + gpio@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "LED A", "LED B", "LED C"; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt new file mode 100644 index 000000000..92ea9c8f6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt @@ -0,0 +1,20 @@ +* TS-4800 FPGA's GPIO controller bindings + +Required properties: +- compatible: Must be "technologic,ts4800-gpio". +- #gpio-cells: Should be two. The first cell is the pin number. +- reg: Physical base address of the controller and length + of memory mapped region. + +Optional property: +- ngpios: See "gpio.txt" + +Example: + +gpio1: gpio { + compatible = "technologic,ts4800-gpio"; + reg = <0x10020 0x6>; + ngpios = <8>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt new file mode 100644 index 000000000..3f8e71b1a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4900.txt @@ -0,0 +1,30 @@ +* Technologic Systems I2C-FPGA's GPIO controller bindings + +This bindings describes the GPIO controller for Technologic's FPGA core. +TS-4900's FPGA encodes the GPIO state on 3 bits, whereas the TS-7970's FPGA +uses 2 bits: it doesn't use a dedicated input bit. + +Required properties: +- compatible: Should be one of the following + "technologic,ts4900-gpio" + "technologic,ts7970-gpio" +- reg: Physical base address of the controller and length + of memory mapped region. +- #gpio-cells: Should be two. The first cell is the pin number. +- gpio-controller: Marks the device node as a gpio controller. + +Optional property: +- ngpios: Number of GPIOs this controller is instantiated with, + the default is 32. See gpio.txt for more details. + +Example: + +&i2c2 { + gpio8: gpio@28 { + compatible = "technologic,ts4900-gpio"; + reg = <0x28>; + #gpio-cells = <2>; + gpio-controller; + ngpios = <32>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt new file mode 100644 index 000000000..66788fda1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -0,0 +1,29 @@ +twl4030 GPIO controller bindings + +Required properties: +- compatible: + - "ti,twl4030-gpio" for twl4030 GPIO controller +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is not used. +- ti,use-leds : Enables LEDA and LEDB outputs if set +- ti,debounce : if n-th bit is set, debounces GPIO-n +- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1) +- ti,pullups : if n-th bit is set, set a pullup on GPIO-n +- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n + +Example: + +twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; + ti,use-leds; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vf610.yaml b/Documentation/devicetree/bindings/gpio/gpio-vf610.yaml new file mode 100644 index 000000000..d2c39dba5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vf610.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-vf610.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale VF610 PORT/GPIO module + +maintainers: + - Stefan Agner <stefan@agner.ch> + +description: | + The Freescale PORT/GPIO modules are two adjacent modules providing GPIO + functionality. Each pair serves 32 GPIOs. The VF610 has 5 instances of + each, and each PORT module has its own interrupt. + + Note: Each GPIO port should have an alias correctly numbered in "aliases" + node. + +properties: + compatible: + oneOf: + - const: fsl,vf610-gpio + - items: + - const: fsl,imx7ulp-gpio + - const: fsl,vf610-gpio + - items: + - enum: + - fsl,imx93-gpio + - fsl,imx8ulp-gpio + - const: fsl,imx7ulp-gpio + + reg: + description: The first reg tuple represents the PORT module, the second tuple + represents the GPIO module. + maxItems: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + "#gpio-cells": + const: 2 + + gpio-controller: true + + clocks: + items: + - description: SoC GPIO clock + - description: SoC PORT clock + + clock-names: + items: + - const: gpio + - const: port + + gpio-ranges: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + gpio1: gpio@40049000 { + compatible = "fsl,vf610-gpio"; + reg = <0x40049000 0x1000>, <0x400ff000 0x40>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 0 32>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-virtio.yaml b/Documentation/devicetree/bindings/gpio/gpio-virtio.yaml new file mode 100644 index 000000000..601d85754 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-virtio.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-virtio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Virtio GPIO controller + +maintainers: + - Viresh Kumar <viresh.kumar@linaro.org> + +allOf: + - $ref: /schemas/virtio/virtio-device.yaml# + +description: + Virtio GPIO controller, see /schemas/virtio/virtio-device.yaml for more + details. + +properties: + $nodename: + const: gpio + + compatible: + const: virtio,device29 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + +required: + - compatible + - gpio-controller + - "#gpio-cells" + +unevaluatedProperties: false + +examples: + - | + virtio@3000 { + compatible = "virtio,mmio"; + reg = <0x3000 0x100>; + interrupts = <41>; + + gpio { + compatible = "virtio,device29"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt new file mode 100644 index 000000000..e90fb987e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt @@ -0,0 +1,64 @@ +APM X-Gene Standby GPIO controller bindings + +This is a gpio controller in the standby domain. It also supports interrupt in +some particular pins which are sourced to its parent interrupt controller +as diagram below: + +-----------------+ + | X-Gene standby | + | GPIO controller +------ GPIO_0 ++------------+ | | ... +| Parent IRQ | EXT_INT_0 | +------ GPIO_8/EXT_INT_0 +| controller | (SPI40) | | ... +| (GICv2) +--------------+ +------ GPIO_[N+8]/EXT_INT_N +| | ... | | +| | EXT_INT_N | +------ GPIO_[N+9] +| | (SPI[40 + N])| | ... +| +--------------+ +------ GPIO_MAX ++------------+ +-----------------+ + +Required properties: +- compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first. +- interrupt-cells: Should be two. + - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N. + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as an interrupt controller. +- apm,nr-gpios: Optional, specify number of gpios pin. +- apm,nr-irqs: Optional, specify number of interrupt pins. +- apm,irq-start: Optional, specify lowest gpio pin support interrupt. + +Example: + sbgpio: gpio@17001000{ + compatible = "apm,xgene-gpio-sb"; + reg = <0x0 0x17001000 0x0 0x400>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <0x0 0x28 0x1>, + <0x0 0x29 0x1>, + <0x0 0x2a 0x1>, + <0x0 0x2b 0x1>, + <0x0 0x2c 0x1>, + <0x0 0x2d 0x1>; + interrupt-parent = <&gic>; + #interrupt-cells = <2>; + interrupt-controller; + apm,nr-gpios = <22>; + apm,nr-irqs = <6>; + apm,irq-start = <8>; + }; + + testuser { + compatible = "example,testuser"; + /* Use the GPIO_13/EXT_INT_5 line as an active high triggered + * level interrupt + */ + interrupts = <5 4>; + interrupt-parent = <&sbgpio>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt new file mode 100644 index 000000000..86dbb05e7 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene.txt @@ -0,0 +1,22 @@ +APM X-Gene SoC GPIO controller bindings + +This is a gpio controller that is part of the flash controller. +This gpio controller controls a total of 48 gpios. + +Required properties: +- compatible: "apm,xgene-gpio" for X-Gene GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio0: gpio0@1701c000 { + compatible = "apm,xgene-gpio"; + reg = <0x0 0x1701c000 0x0 0x40>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt b/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt new file mode 100644 index 000000000..e13cc399b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt @@ -0,0 +1,46 @@ +GPIO Driver for XRA1403 16-BIT GPIO Expander With Reset Input from EXAR + +The XRA1403 is an 16-bit GPIO expander with an SPI interface. Features available: + - Individually programmable inputs: + - Internal pull-up resistors + - Polarity inversion + - Individual interrupt enable + - Rising edge and/or Falling edge interrupt + - Input filter + - Individually programmable outputs + - Output Level Control + - Output Three-State Control + +Properties +---------- +Check documentation for SPI and GPIO controllers regarding properties needed to configure the node. + + - compatible = "exar,xra1403". + - reg - SPI id of the device. + - gpio-controller - marks the node as gpio. + - #gpio-cells - should be two where the first cell is the pin number + and the second one is used for optional parameters. + +Optional properties: +------------------- + - reset-gpios: in case available used to control the device reset line. + - interrupt-controller - marks the node as interrupt controller. + - #interrupt-cells - should be two and represents the number of cells + needed to encode interrupt source. + +Example +-------- + + gpioxra0: gpio@2 { + compatible = "exar,xra1403"; + reg = <2>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + reset-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + spi-max-frequency = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-zevio.txt b/Documentation/devicetree/bindings/gpio/gpio-zevio.txt new file mode 100644 index 000000000..a37bd9ae2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-zevio.txt @@ -0,0 +1,16 @@ +Zevio GPIO controller + +Required properties: +- compatible: Should be "lsi,zevio-gpio" +- reg: Address and length of the register set for the device +- #gpio-cells: Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio: gpio@90000000 { + compatible = "lsi,zevio-gpio"; + reg = <0x90000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.yaml b/Documentation/devicetree/bindings/gpio/gpio-zynq.yaml new file mode 100644 index 000000000..572e1718f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-zynq.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx Zynq GPIO controller + +maintainers: + - Michal Simek <michal.simek@xilinx.com> + +properties: + compatible: + enum: + - xlnx,zynq-gpio-1.0 + - xlnx,zynqmp-gpio-1.0 + - xlnx,versal-gpio-1.0 + - xlnx,pmc-gpio-1.0 + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + interrupts: + maxItems: 1 + + gpio-controller: true + + gpio-line-names: + description: strings describing the names of each gpio line + minItems: 58 + maxItems: 174 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + +allOf: + - if: + properties: + compatible: + enum: + - xlnx,zynqmp-gpio-1.0 + then: + properties: + gpio-line-names: + minItems: 174 + maxItems: 174 + + - if: + properties: + compatible: + enum: + - xlnx,zynq-gpio-1.0 + then: + properties: + gpio-line-names: + minItems: 118 + maxItems: 118 + + - if: + properties: + compatible: + enum: + - xlnx,versal-gpio-1.0 + then: + properties: + gpio-line-names: + minItems: 58 + maxItems: 58 + + - if: + properties: + compatible: + enum: + - xlnx,pmc-gpio-1.0 + then: + properties: + gpio-line-names: + minItems: 116 + maxItems: 116 + +required: + - compatible + - reg + - "#gpio-cells" + - interrupts + - gpio-controller + - interrupt-controller + - "#interrupt-cells" + - clocks + +additionalProperties: false + +examples: + - | + gpio@e000a000 { + #gpio-cells = <2>; + compatible = "xlnx,zynq-gpio-1.0"; + clocks = <&clkc 42>; + gpio-controller; + interrupt-parent = <&intc>; + interrupts = <0 20 4>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0xe000a000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt new file mode 100644 index 000000000..5663e71b7 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -0,0 +1,331 @@ +Specifying GPIO information for devices +======================================= + +1) gpios property +----------------- + +GPIO properties should be named "[<name>-]gpios", with <name> being the purpose +of this GPIO for the device. While a non-existent <name> is considered valid +for compatibility reasons (resolving to the "gpios" property), it is not allowed +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. + +GPIO properties can contain one or more GPIO phandles, but only in exceptional +cases should they contain more than one. If your device uses several GPIOs with +distinct functions, reference each of them under its own property, giving it a +meaningful name. The only case where an array of GPIOs is accepted is when +several GPIOs serve the same function (e.g. a parallel data line). + +The exact purpose of each gpios property must be documented in the device tree +binding of the device. + +The following example could be used to describe GPIO pins used as device enable +and bit-banged data signals: + + gpio1: gpio1 { + gpio-controller; + #gpio-cells = <2>; + }; + [...] + + data-gpios = <&gpio1 12 0>, + <&gpio1 13 0>, + <&gpio1 14 0>, + <&gpio1 15 0>; + +In the above example, &gpio1 uses 2 cells to specify a gpio. The first cell is +a local offset to the GPIO line and the second cell represent consumer flags, +such as if the consumer desire the line to be active low (inverted) or open +drain. This is the recommended practice. + +The exact meaning of each specifier cell is controller specific, and must be +documented in the device tree binding for the device, but it is strongly +recommended to use the two-cell approach. + +Most controllers are specifying a generic flag bitfield in the last cell, so +for these, use the macros defined in +include/dt-bindings/gpio/gpio.h whenever possible: + +Example of a node using GPIOs: + + node { + enable-gpios = <&qe_pio_e 18 GPIO_ACTIVE_HIGH>; + }; + +GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes +GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +Optional standard bitfield specifiers for the last cell: + +- Bit 0: 0 means active high, 1 means active low +- Bit 1: 0 mean push-pull wiring, see: + https://en.wikipedia.org/wiki/Push-pull_output + 1 means single-ended wiring, see: + https://en.wikipedia.org/wiki/Single-ended_triode +- Bit 2: 0 means open-source, 1 means open drain, see: + https://en.wikipedia.org/wiki/Open_collector +- Bit 3: 0 means the output should be maintained during sleep/low-power mode + 1 means the output state can be lost during sleep/low-power mode +- Bit 4: 0 means no pull-up resistor should be enabled + 1 means a pull-up resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-up configuration. If the hardware has more + elaborate pull-up configuration, it should be represented + using a pin control binding. +- Bit 5: 0 means no pull-down resistor should be enabled + 1 means a pull-down resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-down configuration. If the hardware has more + elaborate pull-down configuration, it should be represented + using a pin control binding. + +1.1) GPIO specifier best practices +---------------------------------- + +A gpio-specifier should contain a flag indicating the GPIO polarity; active- +high or active-low. If it does, the following best practices should be +followed: + +The gpio-specifier's polarity flag should represent the physical level at the +GPIO controller that achieves (or represents, for inputs) a logically asserted +value at the device. The exact definition of logically asserted should be +defined by the binding for the device. If the board inverts the signal between +the GPIO controller and the device, then the gpio-specifier will represent the +opposite physical level than the signal at the device's pin. + +When the device's signal polarity is configurable, the binding for the +device must either: + +a) Define a single static polarity for the signal, with the expectation that +any software using that binding would statically program the device to use +that signal polarity. + +The static choice of polarity may be either: + +a1) (Preferred) Dictated by a binding-specific DT property. + +or: + +a2) Defined statically by the DT binding itself. + +In particular, the polarity cannot be derived from the gpio-specifier, since +that would prevent the DT from separately representing the two orthogonal +concepts of configurable signal polarity in the device, and possible board- +level signal inversion. + +or: + +b) Pick a single option for device signal polarity, and document this choice +in the binding. The gpio-specifier should represent the polarity of the signal +(at the GPIO controller) assuming that the device is configured for this +particular signal polarity choice. If software chooses to program the device +to generate or receive a signal of the opposite polarity, software will be +responsible for correctly interpreting (inverting) the GPIO signal at the GPIO +controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must contain both an empty "gpio-controller" +property, and a #gpio-cells integer property, which indicates the number of +cells in a gpio-specifier. + +Some system-on-chips (SoCs) use the concept of GPIO banks. A GPIO bank is an +instance of a hardware IP core on a silicon die, usually exposed to the +programmer as a coherent range of I/O addresses. Usually each such bank is +exposed in the device tree as an individual gpio-controller node, reflecting +the fact that the hardware was synthesized by reusing the same IP block a +few times over. + +Optionally, a GPIO controller may have a "ngpios" property. This property +indicates the number of in-use slots of available slots for GPIOs. The +typical example is something like this: the hardware register is 32 bits +wide, but only 18 of the bits have a physical counterpart. The driver is +generally written so that all 32 bits can be used, but the IP block is reused +in a lot of designs, some using all 32 bits, some using 18 and some using +12. In this case, setting "ngpios = <18>;" informs the driver that only the +first 18 GPIOs, at local offset 0 .. 17, are in use. + +If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an +additional set of tuples is needed to specify which GPIOs are unusable, with +the gpio-reserved-ranges binding. This property indicates the start and size +of the GPIOs that can't be used. + +Optionally, a GPIO controller may have a "gpio-line-names" property. This is +an array of strings defining the names of the GPIO lines going out of the +GPIO controller. This name should be the most meaningful producer name +for the system, such as a rail name indicating the usage. Package names +such as pin name are discouraged: such lines have opaque names (since they +are by definition generic purpose) and such names are usually not very +helpful. For example "MMC-CD", "Red LED Vdd" and "ethernet reset" are +reasonable line names as they describe what the line is used for. "GPIO0" +is not a good name to give to a GPIO line. Placeholders are discouraged: +rather use the "" (blank string) if the use of the GPIO line is undefined +in your design. The names are assigned starting from line offset 0 from +left to right from the passed array. An incomplete array (where the number +of passed named are less than ngpios) will still be used up until the last +provided valid line index. + +Example: + +gpio-controller@00000000 { + compatible = "foo"; + reg = <0x00000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <18>; + gpio-reserved-ranges = <0 4>, <12 2>; + gpio-line-names = "MMC-CD", "MMC-WP", "VDD eth", "RST eth", "LED R", + "LED G", "LED B", "Col A", "Col B", "Col C", "Col D", + "Row A", "Row B", "Row C", "Row D", "NMI button", + "poweroff", "reset"; +} + +The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism +providing automatic GPIO request and configuration as part of the +gpio-controller's driver probe function. + +Each GPIO hog definition is represented as a child node of the GPIO controller. +Required properties: +- gpio-hog: A property specifying that this child node represents a GPIO hog. +- gpios: Store the GPIO information (id, flags, ...) for each GPIO to + affect. Shall contain an integer multiple of the number of cells + specified in its parent node (GPIO controller node). +Only one of the following properties scanned in the order shown below. +This means that when multiple properties are present they will be searched +in the order presented below and the first match is taken as the intended +configuration. +- input: A property specifying to set the GPIO direction as input. +- output-low A property specifying to set the GPIO direction as output with + the value low. +- output-high A property specifying to set the GPIO direction as output with + the value high. + +Optional properties: +- line-name: The GPIO label name. If not present the node name is used. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + #gpio-cells = <2>; + + line_b-hog { + gpio-hog; + gpios = <6 0>; + output-low; + line-name = "foo-bar-gpio"; + }; + }; + + qe_pio_e: gpio-controller@1460 { + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + #gpio-cells = <2>; + }; + +2.1) gpio- and pin-controller interaction +----------------------------------------- + +Some or all of the GPIOs provided by a GPIO controller may be routed to pins +on the package via a pin controller. This allows muxing those pins between +GPIO and other functions. It is a fairly common practice among silicon +engineers. + +2.2) Ordinary (numerical) GPIO ranges +------------------------------------- + +It is useful to represent which GPIOs correspond to which pins on which pin +controllers. The gpio-ranges property described below represents this with +a discrete set of ranges mapping pins from the pin controller local number space +to pins in the GPIO controller local number space. + +The format is: <[pin controller phandle], [GPIO controller offset], + [pin controller offset], [number of pins]>; + +The GPIO controller offset pertains to the GPIO controller node containing the +range definition. + +The pin controller node referenced by the phandle must conform to the bindings +described in pinctrl/pinctrl-bindings.txt. + +Each offset runs from 0 to N. It is perfectly fine to pile any number of +ranges with just one pin-to-GPIO line mapping if the ranges are concocted, but +in practice these ranges are often lumped in discrete sets. + +Example: + + gpio-ranges = <&foo 0 20 10>, <&bar 10 50 20>; + +This means: +- pins 20..29 on pin controller "foo" is mapped to GPIO line 0..9 and +- pins 50..69 on pin controller "bar" is mapped to GPIO line 10..29 + + +Verbose example: + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>; + }; + +Here, a single GPIO controller has GPIOs 0..9 routed to pin controller +pinctrl1's pins 20..29, and GPIOs 10..29 routed to pin controller pinctrl2's +pins 50..69. + + +2.3) GPIO ranges from named pin groups +-------------------------------------- + +It is also possible to use pin groups for gpio ranges when pin groups are the +easiest and most convenient mapping. + +Both both <pinctrl-base> and <count> must set to 0 when using named pin groups +names. + +The property gpio-ranges-group-names must contain exactly one string for each +range. + +Elements of gpio-ranges-group-names must contain the name of a pin group +defined in the respective pin controller. The number of pins/GPIO lines in the +range is the number of pins in that pin group. The number of pins of that +group is defined int the implementation and not in the device tree. + +If numerical and named pin groups are mixed, the string corresponding to a +numerical pin range in gpio-ranges-group-names must be empty. + +Example: + + gpio_pio_i: gpio-controller@14b0 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1480 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 0 20 10>, + <&pinctrl2 10 0 0>, + <&pinctrl1 15 0 10>, + <&pinctrl2 25 0 0>; + gpio-ranges-group-names = "", + "foo", + "", + "bar"; + }; + +Here, three GPIO ranges are defined referring to two pin controllers. + +pinctrl1 GPIO ranges are defined using pin numbers whereas the GPIO ranges +in pinctrl2 are defined using the pin groups named "foo" and "bar". + +Previous versions of this binding required all pin controller nodes that +were referenced by any gpio-ranges property to contain a property named +#gpio-range-cells with value <3>. This requirement is now deprecated. +However, that property may still exist in older device trees for +compatibility reasons, and would still be required even in new device +trees that need to be compatible with older software. diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt new file mode 100644 index 000000000..29416f9c3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -0,0 +1,31 @@ +* Atmel GPIO controller (PIO) + +Required properties: +- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5. +- reg: Should contain GPIO controller registers location and length +- interrupts: Should be the port interrupt shared by all the pins. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters to declare if the GPIO + is active high or low. See gpio.txt. +- gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. The first cell is the pin number and the + second cell is used to specify irq type flags, see the two cell description + in interrupt-controller/interrupts.txt for details. + +optional properties: +- #gpio-lines: Number of gpio if absent 32. + + +Example: + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + #gpio-lines = <19>; + interrupt-controller; + #interrupt-cells = <2>; + }; + diff --git a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt new file mode 100644 index 000000000..49819367a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt @@ -0,0 +1,43 @@ +NXP LPC32xx SoC GPIO controller + +Required properties: +- compatible: must be "nxp,lpc3220-gpio" +- reg: Physical base address and length of the controller's registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be 3: + 1) bank: + 0: GPIO P0 + 1: GPIO P1 + 2: GPIO P2 + 3: GPIO P3 + 4: GPI P3 + 5: GPO P3 + 2) pin number + 3) optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- reg: Index of the GPIO group + +Example: + + gpio: gpio@40028000 { + compatible = "nxp,lpc3220-gpio"; + reg = <0x40028000 0x1000>; + gpio-controller; + #gpio-cells = <3>; /* bank, pin, flags */ + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt new file mode 100644 index 000000000..966514744 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt @@ -0,0 +1,47 @@ +* Oxford Semiconductor OXNAS SoC GPIO Controller + +Please refer to gpio.txt for generic information regarding GPIO bindings. + +Required properties: + - compatible: "oxsemi,ox810se-gpio" or "oxsemi,ox820-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - gpio-ranges: Interaction with the PINCTRL subsystem, it also specifies the + gpio base and count, should be in the format of numeric-gpio-range as + specified in the gpio.txt file. + +Example: + +gpio0: gpio@0 { + compatible = "oxsemi,ox810se-gpio"; + reg = <0x000000 0x100000>; + interrupts = <21>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pinctrl 0 0 32>; +}; + +keys { + ... + + button-esc { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt new file mode 100644 index 000000000..d58b3958f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt @@ -0,0 +1,24 @@ +* IBM/AMCC/APM GPIO Controller for PowerPC 4XX series and compatible SoCs + +All GPIOs are pin-shared with other functions. DCRs control whether a +particular pin that has GPIO capabilities acts as a GPIO or is used for +another purpose. GPIO outputs are separately programmable to emulate +an open-drain driver. + +Required properties: + - compatible: must be "ibm,ppc4xx-gpio" + - reg: address and length of the register set for the device + - #gpio-cells: must be set to 2. The first cell is the pin number + and the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: marks the device node as a gpio controller. + +Example: + +GPIO0: gpio@ef600b00 { + compatible = "ibm,ppc4xx-gpio"; + reg = <0xef600b00 0x00000048>; + #gpio-cells = <2>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/idt,32434-gpio.yaml b/Documentation/devicetree/bindings/gpio/idt,32434-gpio.yaml new file mode 100644 index 000000000..d38de8144 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/idt,32434-gpio.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/idt,32434-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IDT 79RC32434 GPIO controller + +maintainers: + - Thomas Bogendoerfer <tsbogend@alpha.franken.de> + +properties: + compatible: + const: idt,32434-gpio + + reg: + maxItems: 2 + + reg-names: + items: + - const: gpio + - const: pic + + gpio-controller: true + + "#gpio-cells": + const: 2 + + ngpios: + minimum: 1 + maximum: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + gpio0: gpio@50004 { + compatible = "idt,32434-gpio"; + reg = <0x50004 0x10>, <0x38030 0x0c>; + reg-names = "gpio", "pic"; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + gpio-controller; + #gpio-cells = <2>; + + ngpios = <14>; + }; diff --git a/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt new file mode 100644 index 000000000..8dc41ed99 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt @@ -0,0 +1,38 @@ +Intel IXP4xx XScale Networking Processors GPIO + +This GPIO controller is found in the Intel IXP4xx processors. +It supports 16 GPIO lines. + +The interrupt portions of the GPIO controller is hierarchical: +the synchronous edge detector is part of the GPIO block, but the +actual enabling/disabling of the interrupt line is done in the +main IXP4xx interrupt controller which has a 1:1 mapping for +the first 12 GPIO lines to 12 system interrupts. + +The remaining 4 GPIO lines can not be used for receiving +interrupts. + +The interrupt parent of this GPIO controller must be the +IXP4xx interrupt controller. + +Required properties: + +- compatible : Should be + "intel,ixp4xx-gpio" +- reg : Should contain registers location and length +- gpio-controller : marks this as a GPIO controller +- #gpio-cells : Should be 2, see gpio/gpio.txt +- interrupt-controller : marks this as an interrupt controller +- #interrupt-cells : a standard two-cell interrupt, see + interrupt-controller/interrupts.txt + +Example: + +gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml new file mode 100644 index 000000000..b03247183 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/kontron,sl28cpld-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO driver for the sl28cpld board management controller + +maintainers: + - Michael Walle <michael@walle.cc> + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + + There are three flavors of the GPIO controller, one full featured + input/output with interrupt support (kontron,sl28cpld-gpio), one + output-only (kontron,sl28-gpo) and one input-only (kontron,sl28-gpi). + + Each controller supports 8 GPIO lines. + +properties: + compatible: + enum: + - kontron,sl28cpld-gpio + - kontron,sl28cpld-gpi + - kontron,sl28cpld-gpo + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-line-names: + minItems: 1 + maxItems: 8 + +required: + - compatible + - "#gpio-cells" + - gpio-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml new file mode 100644 index 000000000..5bbb2a312 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/mediatek,mt7621-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT7621 SoC GPIO controller + +maintainers: + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: | + The IP core used inside these SoCs has 3 banks of 32 GPIOs each. + The registers of all the banks are interwoven inside one single IO range. + We load one GPIO controller instance per bank. Also the GPIO controller can receive + interrupts on any of the GPIOs, either edge or level. It then interrupts the CPU + using GIC INT12. + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: mediatek,mt7621-gpio + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + gpio-ranges: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + - gpio-ranges + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/mips-gic.h> + + gpio@600 { + compatible = "mediatek,mt7621-gpio"; + reg = <0x600 0x100>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 95>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 12 IRQ_TYPE_LEVEL_HIGH>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/microchip,mpfs-gpio.yaml b/Documentation/devicetree/bindings/gpio/microchip,mpfs-gpio.yaml new file mode 100644 index 000000000..d481e7895 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,mpfs-gpio.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/microchip,mpfs-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MPFS GPIO Controller + +maintainers: + - Conor Dooley <conor.dooley@microchip.com> + +properties: + compatible: + items: + - enum: + - microchip,mpfs-gpio + + reg: + maxItems: 1 + + interrupts: + description: + Interrupt mapping, one per GPIO. Maximum 32 GPIOs. + minItems: 1 + maxItems: 32 + + interrupt-controller: true + + clocks: + maxItems: 1 + + "#gpio-cells": + const: 2 + + "#interrupt-cells": + const: 1 + + ngpios: + description: + The number of GPIOs available. + minimum: 1 + maximum: 32 + default: 32 + + gpio-controller: true + +patternProperties: + "^.+-hog(-[0-9]+)?$": + type: object + + additionalProperties: false + + properties: + gpio-hog: true + gpios: true + input: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + +required: + - compatible + - reg + - interrupts + - "#interrupt-cells" + - interrupt-controller + - "#gpio-cells" + - gpio-controller + - clocks + +additionalProperties: false + +examples: + - | + gpio@20122000 { + compatible = "microchip,mpfs-gpio"; + reg = <0x20122000 0x1000>; + clocks = <&clkcfg 25>; + interrupt-parent = <&plic>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + interrupts = <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>, + <53>, <53>, <53>, <53>; + }; +... diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 000000000..dd031fc93 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&rootclk PB4CLK>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml b/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml new file mode 100644 index 000000000..9cf6137dd --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml @@ -0,0 +1,172 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/mrvl-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell PXA GPIO controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + - Rob Herring <robh+dt@kernel.org> + +allOf: + - if: + properties: + compatible: + contains: + enum: + - intel,pxa25x-gpio + - intel,pxa26x-gpio + - intel,pxa27x-gpio + - intel,pxa3xx-gpio + then: + properties: + interrupts: + minItems: 3 + maxItems: 3 + interrupt-names: + items: + - const: gpio0 + - const: gpio1 + - const: gpio_mux + - if: + properties: + compatible: + contains: + enum: + - marvell,mmp-gpio + - marvell,mmp2-gpio + then: + properties: + interrupts: + maxItems: 1 + interrupt-names: + items: + - const: gpio_mux + +properties: + $nodename: + pattern: '^gpio@[0-9a-f]+$' + + compatible: + enum: + - intel,pxa25x-gpio + - intel,pxa26x-gpio + - intel,pxa27x-gpio + - intel,pxa3xx-gpio + - marvell,mmp-gpio + - marvell,mmp2-gpio + - marvell,pxa93x-gpio + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + ranges: true + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-ranges: true + + interrupts: true + + interrupt-names: true + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + +patternProperties: + '^gpio@[0-9a-f]*$': + type: object + properties: + reg: + maxItems: 1 + + required: + - reg + + additionalProperties: false + +required: + - compatible + - '#address-cells' + - '#size-cells' + - reg + - gpio-controller + - '#gpio-cells' + - interrupts + - interrupt-names + - interrupt-controller + - '#interrupt-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/pxa-clock.h> + gpio@40e00000 { + compatible = "intel,pxa3xx-gpio"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40e00000 0x10000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <8>, <9>, <10>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + clocks = <&clks CLK_GPIO>; + interrupt-controller; + #interrupt-cells = <2>; + }; + - | + #include <dt-bindings/clock/marvell,pxa910.h> + gpio@d4019000 { + compatible = "marvell,mmp-gpio"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4019000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <49>; + interrupt-names = "gpio_mux"; + clocks = <&soc_clocks PXA910_CLK_GPIO>; + resets = <&soc_clocks PXA910_CLK_GPIO>; + interrupt-controller; + #interrupt-cells = <2>; + ranges; + + gpio@d4019000 { + reg = <0xd4019000 0x4>; + }; + + gpio@d4019004 { + reg = <0xd4019004 0x4>; + }; + + gpio@d4019008 { + reg = <0xd4019008 0x4>; + }; + + gpio@d4019100 { + reg = <0xd4019100 0x4>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml b/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml new file mode 100644 index 000000000..18fe90387 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/mstar,msc313-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MStar/SigmaStar GPIO controller + +maintainers: + - Daniel Palmer <daniel@thingy.jp> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + enum: + - mstar,msc313-gpio + - sstar,ssd20xd-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-ranges: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/msc313-gpio.h> + + gpio: gpio@207800 { + compatible = "mstar,msc313-gpio"; + #gpio-cells = <2>; + reg = <0x207800 0x200>; + gpio-controller; + gpio-ranges = <&pinctrl 0 36 22>, + <&pinctrl 22 63 4>, + <&pinctrl 26 68 6>; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&intc_fiq>; + }; diff --git a/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt new file mode 100644 index 000000000..50ec2e690 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt @@ -0,0 +1,22 @@ +Binding for the GPIO extension bus found on some LaCie/Seagate boards +(Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-gpio-ext". +- addr-gpios: GPIOs representing the address register (LSB -> MSB). +- data-gpios: GPIOs representing the data register (LSB -> MSB). +- enable-gpio: latches the new configuration (address, data) on raising edge. + +Example: + +netxbig_gpio_ext: netxbig-gpio-ext { + compatible = "lacie,netxbig-gpio-ext"; + + addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH + &gpio1 16 GPIO_ACTIVE_HIGH + &gpio1 17 GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH + &gpio1 14 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt new file mode 100644 index 000000000..ca2f8c745 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt @@ -0,0 +1,38 @@ +Bindings for the National Instruments 169445 GPIO NAND controller + +The 169445 GPIO NAND controller has two memory mapped GPIO registers, one +for input (the ready signal) and one for output (control signals). It is +intended to be used with the GPIO NAND driver. + +Required properties: + - compatible: should be "ni,169445-nand-gpio" + - reg-names: must contain + "dat" - data register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - no-output: disables driving output on the pins + +Examples: + gpio1: nand-gpio-out@1f300010 { + compatible = "ni,169445-nand-gpio"; + reg = <0x1f300010 0x4>; + reg-names = "dat"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio2: nand-gpio-in@1f300014 { + compatible = "ni,169445-nand-gpio"; + reg = <0x1f300014 0x4>; + reg-names = "dat"; + gpio-controller; + #gpio-cells = <2>; + no-output; + }; diff --git a/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt b/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt new file mode 100644 index 000000000..df63da463 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt @@ -0,0 +1,26 @@ +Nintendo Wii (Hollywood) GPIO controller + +Required properties: +- compatible: "nintendo,hollywood-gpio" +- reg: Physical base address and length of the controller's registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). + +Optional properties: +- ngpios: see Documentation/devicetree/bindings/gpio/gpio.txt +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- interrupts: Interrupt specifier for the controller's Broadway (PowerPC) + interrupt. + +Example: + + GPIO: gpio@d8000c0 { + #gpio-cells = <2>; + compatible = "nintendo,hollywood-gpio"; + reg = <0x0d8000c0 0x40>; + gpio-controller; + ngpios = <24>; + } diff --git a/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.yaml b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.yaml new file mode 100644 index 000000000..4ef06b2ff --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.yaml @@ -0,0 +1,214 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/nvidia,tegra186-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra GPIO Controller (Tegra186 and later) + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + Tegra186 contains two GPIO controllers; a main controller and an "AON" + controller. This binding document applies to both controllers. The register + layouts for the controllers share many similarities, but also some + significant differences. Hence, this document describes closely related but + different bindings and compatible values. + + The Tegra186 GPIO controller allows software to set the IO direction of, + and read/write the value of, numerous GPIO signals. Routing of GPIO signals + to package balls is under the control of a separate pin controller hardware + block. Two major sets of registers exist: + + a) Security registers, which allow configuration of allowed access to the + GPIO register set. These registers exist in a single contiguous block + of physical address space. The size of this block, and the security + features available, varies between the different GPIO controllers. + + Access to this set of registers is not necessary in all circumstances. + Code that wishes to configure access to the GPIO registers needs access + to these registers to do so. Code which simply wishes to read or write + GPIO data does not need access to these registers. + + b) GPIO registers, which allow manipulation of the GPIO signals. In some + GPIO controllers, these registers are exposed via multiple "physical + aliases" in address space, each of which access the same underlying + state. See the hardware documentation for rationale. Any particular + GPIO client is expected to access just one of these physical aliases. + + Tegra HW documentation describes a unified naming convention for all GPIOs + implemented by the SoC. Each GPIO is assigned to a port, and a port may + control a number of GPIOs. Thus, each GPIO is named according to an + alphabetical port name and an integer GPIO name within the port. For + example, GPIO_PA0, GPIO_PN6, or GPIO_PCC3. + + The number of ports implemented by each GPIO controller varies. The number + of implemented GPIOs within each port varies. GPIO registers within a + controller are grouped and laid out according to the port they affect. + + The mapping from port name to the GPIO controller that implements that + port, and the mapping from port name to register offset within a + controller, are both extremely non-linear. The header file + <dt-bindings/gpio/tegra186-gpio.h> describes the port-level mapping. In + that file, the naming convention for ports matches the HW documentation. + The values chosen for the names are alphabetically sorted within a + particular controller. Drivers need to map between the DT GPIO IDs and HW + register offsets using a lookup table. + + Each GPIO controller can generate a number of interrupt signals. Each + signal represents the aggregate status for all GPIOs within a set of + ports. Thus, the number of interrupt signals generated by a controller + varies as a rough function of the number of ports it implements. Note + that the HW documentation refers to both the overall controller HW + module and the sets-of-ports as "controllers". + + Each GPIO controller in fact generates multiple interrupts signals for + each set of ports. Each GPIO may be configured to feed into a specific + one of the interrupt signals generated by a set-of-ports. The intent is + for each generated signal to be routed to a different CPU, thus allowing + different CPUs to each handle subsets of the interrupts within a port. + The status of each of these per-port-set signals is reported via a + separate register. Thus, a driver needs to know which status register to + observe. This binding currently defines no configuration mechanism for + this. By default, drivers should use register + GPIO_${port}_INTERRUPT_STATUS_G1_0. Future revisions to the binding could + define a property to configure this. + +properties: + compatible: + enum: + - nvidia,tegra186-gpio + - nvidia,tegra186-gpio-aon + - nvidia,tegra194-gpio + - nvidia,tegra194-gpio-aon + - nvidia,tegra234-gpio + - nvidia,tegra234-gpio-aon + + reg-names: + items: + - const: security + - const: gpio + minItems: 1 + + reg: + items: + - description: Security configuration registers. + - description: | + GPIO control registers. This may cover either: + + a) The single physical alias that this OS should use. + b) All physical aliases that exist in the controller. This is + appropriate when the OS is responsible for managing assignment + of the physical aliases. + minItems: 1 + + interrupts: + description: The interrupt outputs from the HW block, one per set of + ports, in the order the HW manual describes them. The number of entries + required varies depending on compatible value. + + gpio-controller: true + + "#gpio-cells": + description: | + Indicates how many cells are used in a consumer's GPIO specifier. In the + specifier: + + - The first cell is the pin number. + See <dt-bindings/gpio/tegra186-gpio.h>. + - The second cell contains flags: + - Bit 0 specifies polarity + - 0: Active-high (normal). + - 1: Active-low (inverted). + const: 2 + + interrupt-controller: true + + "#interrupt-cells": + description: | + Indicates how many cells are used in a consumer's interrupt specifier. + In the specifier: + + - The first cell is the GPIO number. + See <dt-bindings/gpio/tegra186-gpio.h>. + - The second cell is contains flags: + - Bits [3:0] indicate trigger type and level: + - 1: Low-to-high edge triggered. + - 2: High-to-low edge triggered. + - 4: Active high level-sensitive. + - 8: Active low level-sensitive. + + Valid combinations are 1, 2, 3, 4, 8. + const: 2 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra186-gpio + - nvidia,tegra194-gpio + - nvidia,tegra234-gpio + then: + properties: + interrupts: + minItems: 6 + maxItems: 48 + + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra186-gpio-aon + - nvidia,tegra194-gpio-aon + - nvidia,tegra234-gpio-aon + then: + properties: + interrupts: + minItems: 1 + maxItems: 4 + +required: + - compatible + - reg + - reg-names + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + gpio@2200000 { + compatible = "nvidia,tegra186-gpio"; + reg-names = "security", "gpio"; + reg = <0x2200000 0x10000>, + <0x2210000 0x10000>; + interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>, + <0 50 IRQ_TYPE_LEVEL_HIGH>, + <0 53 IRQ_TYPE_LEVEL_HIGH>, + <0 56 IRQ_TYPE_LEVEL_HIGH>, + <0 59 IRQ_TYPE_LEVEL_HIGH>, + <0 180 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@c2f0000 { + compatible = "nvidia,tegra186-gpio-aon"; + reg-names = "security", "gpio"; + reg = <0xc2f0000 0x1000>, + <0xc2f1000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.yaml b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.yaml new file mode 100644 index 000000000..94b51749e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/nvidia,tegra20-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra GPIO Controller (Tegra20 - Tegra210) + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +properties: + compatible: + oneOf: + - enum: + - nvidia,tegra20-gpio + - nvidia,tegra30-gpio + + - items: + - enum: + - nvidia,tegra114-gpio + - nvidia,tegra124-gpio + - nvidia,tegra210-gpio + - const: nvidia,tegra30-gpio + + reg: + maxItems: 1 + + interrupts: + description: The interrupt outputs from the controller. For Tegra20, + there should be 7 interrupts specified, and for Tegra30, there should + be 8 interrupts specified. + + "#gpio-cells": + description: The first cell is the pin number and the second cell is used + to specify the GPIO polarity (0 = active high, 1 = active low). + const: 2 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + "#interrupt-cells": + description: | + Should be 2. The first cell is the GPIO number. The second cell is + used to specify flags: + + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + + Valid combinations are 1, 2, 3, 4, 8. + const: 2 + + interrupt-controller: true + +allOf: + - if: + properties: + compatible: + contains: + const: nvidia,tegra30-gpio + then: + properties: + interrupts: + minItems: 8 + maxItems: 8 + else: + properties: + interrupts: + minItems: 7 + maxItems: 7 + +required: + - compatible + - reg + - interrupts + - "#gpio-cells" + - gpio-controller + - "#interrupt-cells" + - interrupt-controller + +additionalProperties: + type: object + required: + - gpio-hog + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + gpio: gpio@6000d000 { + compatible = "nvidia,tegra20-gpio"; + reg = <0x6000d000 0x1000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt new file mode 100644 index 000000000..627efc78e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt @@ -0,0 +1,59 @@ +NXP LPC18xx/43xx GPIO controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible : Should be "nxp,lpc1850-gpio" +- reg : List of addresses and lengths of the GPIO controller + register sets +- reg-names : Should be "gpio", "gpio-pin-ic", "gpio-group0-ic" and + "gpio-gpoup1-ic" +- clocks : Phandle and clock specifier pair for GPIO controller +- resets : Phandle and reset specifier pair for GPIO controller +- gpio-controller : Marks the device node as a GPIO controller +- #gpio-cells : Should be two: + - The first cell is the GPIO line number + - The second cell is used to specify polarity +- interrupt-controller : Marks the device node as an interrupt controller +- #interrupt-cells : Should be two: + - The first cell is an interrupt number within + 0..9 range, for GPIO pin interrupts it is equal + to 'nxp,gpio-pin-interrupt' property value of + GPIO pin configuration, 8 is for GPIO GROUP0 + interrupt, 9 is for GPIO GROUP1 interrupt + - The second cell is used to specify interrupt type + +Optional properties: +- gpio-ranges : Mapping between GPIO and pinctrl + +Example: +#define LPC_GPIO(port, pin) (port * 32 + pin) +#define LPC_PIN(port, pin) (0x##port * 32 + pin) + +gpio: gpio@400f4000 { + compatible = "nxp,lpc1850-gpio"; + reg = <0x400f4000 0x4000>, <0x40087000 0x1000>, + <0x40088000 0x1000>, <0x40089000 0x1000>; + reg-names = "gpio", "gpio-pin-ic", + "gpio-group0-ic", "gpio-gpoup1-ic"; + clocks = <&ccu1 CLK_CPU_GPIO>; + resets = <&rgu 28>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>, + ... + <&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>; +}; + +gpio_joystick { + compatible = "gpio-keys"; + ... + + button0 { + ... + interrupt-parent = <&gpio>; + interrupts = <1 IRQ_TYPE_EDGE_BOTH>; + gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml b/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml new file mode 100644 index 000000000..f0ff66c4c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/nxp,pcf8575.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PCF857x-compatible I/O expanders + +maintainers: + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + +description: + The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be + driven high by a pull-up current source or driven low to ground. This + combines the direction and output level into a single bit per line, which + can't be read back. We can't actually know at initialization time whether a + line is configured (a) as output and driving the signal low/high, or (b) as + input and reporting a low/high value, without knowing the last value written + since the chip came out of reset (if any). The only reliable solution for + setting up line direction is thus to do it explicitly. + +properties: + compatible: + enum: + - maxim,max7328 + - maxim,max7329 + - nxp,pca8574 + - nxp,pca8575 + - nxp,pca9670 + - nxp,pca9671 + - nxp,pca9672 + - nxp,pca9673 + - nxp,pca9674 + - nxp,pca9675 + - nxp,pcf8574 + - nxp,pcf8574a + - nxp,pcf8575 + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + description: + The first cell is the GPIO number and the second cell specifies GPIO + flags, as defined in <dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH + and GPIO_ACTIVE_LOW flags are supported. + + lines-initial-states: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Bitmask that specifies the initial state of each line. + When a bit is set to zero, the corresponding line will be initialized to + the input (pulled-up) state. + When the bit is set to one, the line will be initialized to the + low-level output state. + If the property is not specified all lines will be initialized to the + input state. + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + wakeup-source: true + +patternProperties: + "^(.+-hog(-[0-9]+)?)$": + type: object + + required: + - gpio-hog + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pcf8575: gpio@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + interrupt-parent = <&irqpin2>; + interrupts = <3 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml new file mode 100644 index 000000000..bd35cbf7f --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/pl061-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL061 GPIO controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Rob Herring <robh@kernel.org> + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl061 + required: + - compatible + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + items: + - const: arm,pl061 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + oneOf: + - maxItems: 1 + - maxItems: 8 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + clock-names: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-line-names: true + + gpio-ranges: + minItems: 1 + maxItems: 8 + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - clocks + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/gpio/qcom,wcd934x-gpio.yaml b/Documentation/devicetree/bindings/gpio/qcom,wcd934x-gpio.yaml new file mode 100644 index 000000000..32a566ec3 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/qcom,wcd934x-gpio.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/qcom,wcd934x-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: WCD9340/WCD9341 GPIO controller + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + Qualcomm Technologies Inc WCD9340/WCD9341 Audio Codec has integrated + gpio controller to control 5 gpios on the chip. + +properties: + compatible: + enum: + - qcom,wcd9340-gpio + - qcom,wcd9341-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + wcdgpio: gpio@42 { + compatible = "qcom,wcd9340-gpio"; + reg = <0x042 0x2>; + gpio-controller; + #gpio-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt b/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt new file mode 100644 index 000000000..ce97265e2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/raspberrypi,firmware-gpio.txt @@ -0,0 +1,30 @@ +Raspberry Pi GPIO expander + +The Raspberry Pi 3 GPIO expander is controlled by the VC4 firmware. The +firmware exposes a mailbox interface that allows the ARM core to control the +GPIO lines on the expander. + +The Raspberry Pi GPIO expander node must be a child node of the Raspberry Pi +firmware node. + +Required properties: + +- compatible : Should be "raspberrypi,firmware-gpio" +- gpio-controller : Marks the device node as a gpio controller +- #gpio-cells : Should be two. The first cell is the pin number, and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Example: + +firmware: firmware-rpi { + compatible = "raspberrypi,bcm2835-firmware"; + mboxes = <&mailbox>; + + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml b/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml new file mode 100644 index 000000000..39fd959c4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/realtek,otto-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek Otto GPIO controller + +maintainers: + - Sander Vanheule <sander@svanheule.net> + - Bert Vermeulen <bert@biot.com> + +description: | + Realtek's GPIO controller on their MIPS switch SoCs (Otto platform) consists + of two banks of 32 GPIOs. These GPIOs can generate edge-triggered interrupts. + Each bank's interrupts are cascased into one interrupt line on the parent + interrupt controller, if provided. + This binding allows defining a single bank in the devicetree. The interrupt + controller is not supported on the fallback compatible name, which only + allows for GPIO port use. + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + items: + - enum: + - realtek,rtl8380-gpio + - realtek,rtl8390-gpio + - realtek,rtl9300-gpio + - realtek,rtl9310-gpio + - const: realtek,otto-gpio + + reg: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + ngpios: + minimum: 1 + maximum: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +if: + properties: + compatible: + contains: + const: realtek,rtl9300-gpio +then: + properties: + reg: + items: + - description: GPIO and interrupt control + - description: interrupt CPU map +else: + properties: + reg: + items: + - description: GPIO and interrupt control + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +dependencies: + interrupt-controller: [ interrupts ] + +examples: + - | + gpio@3500 { + compatible = "realtek,rtl8380-gpio", "realtek,otto-gpio"; + reg = <0x3500 0x1c>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <24>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&rtlintc>; + interrupts = <23>; + }; + - | + gpio@3300 { + compatible = "realtek,rtl9300-gpio", "realtek,otto-gpio"; + reg = <0x3300 0x1c>, <0x3338 0x8>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <24>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&rtlintc>; + interrupts = <13>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/renesas,em-gio.yaml b/Documentation/devicetree/bindings/gpio/renesas,em-gio.yaml new file mode 100644 index 000000000..8bdef812c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/renesas,em-gio.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/renesas,em-gio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas EMMA Mobile General Purpose I/O Interface + +maintainers: + - Magnus Damm <magnus.damm@gmail.com> + +properties: + compatible: + const: renesas,em-gio + + reg: + items: + - description: First set of contiguous registers + - description: Second set of contiguous registers + + interrupts: + items: + - description: Interrupt for the first set of 16 GPIO ports + - description: Interrupt for the second set of 16 GPIO ports + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-ranges: + maxItems: 1 + + ngpios: + minimum: 1 + maximum: 32 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + +required: + - compatible + - reg + - interrupts + - gpio-controller + - '#gpio-cells' + - gpio-ranges + - ngpios + - interrupt-controller + - '#interrupt-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + gpio0: gpio@e0050000 { + compatible = "renesas,em-gio"; + reg = <0xe0050000 0x2c>, <0xe0050040 0x20>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 0 32>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,rcar-gpio.yaml b/Documentation/devicetree/bindings/gpio/renesas,rcar-gpio.yaml new file mode 100644 index 000000000..aa424e2b9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/renesas,rcar-gpio.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/renesas,rcar-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car General-Purpose Input/Output Ports (GPIO) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,gpio-r8a7778 # R-Car M1 + - renesas,gpio-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-gpio # R-Car Gen1 + + - items: + - enum: + - renesas,gpio-r8a7742 # RZ/G1H + - renesas,gpio-r8a7743 # RZ/G1M + - renesas,gpio-r8a7744 # RZ/G1N + - renesas,gpio-r8a7745 # RZ/G1E + - renesas,gpio-r8a77470 # RZ/G1C + - renesas,gpio-r8a7790 # R-Car H2 + - renesas,gpio-r8a7791 # R-Car M2-W + - renesas,gpio-r8a7792 # R-Car V2H + - renesas,gpio-r8a7793 # R-Car M2-N + - renesas,gpio-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-gpio # R-Car Gen2 or RZ/G1 + + - items: + - enum: + - renesas,gpio-r8a774a1 # RZ/G2M + - renesas,gpio-r8a774b1 # RZ/G2N + - renesas,gpio-r8a774c0 # RZ/G2E + - renesas,gpio-r8a774e1 # RZ/G2H + - renesas,gpio-r8a7795 # R-Car H3 + - renesas,gpio-r8a7796 # R-Car M3-W + - renesas,gpio-r8a77961 # R-Car M3-W+ + - renesas,gpio-r8a77965 # R-Car M3-N + - renesas,gpio-r8a77970 # R-Car V3M + - renesas,gpio-r8a77980 # R-Car V3H + - renesas,gpio-r8a77990 # R-Car E3 + - renesas,gpio-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-gpio # R-Car Gen3 or RZ/G2 + + - items: + - enum: + - renesas,gpio-r8a779a0 # R-Car V3U + - renesas,gpio-r8a779f0 # R-Car S4-8 + - renesas,gpio-r8a779g0 # R-Car V4H + - const: renesas,rcar-gen4-gpio # R-Car Gen4 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + gpio-ranges: + maxItems: 1 + + gpio-reserved-ranges: + minItems: 1 + maxItems: 8 + +patternProperties: + "^.*$": + if: + type: object + then: + properties: + gpio-hog: true + gpios: true + input: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - gpio-controller + - '#gpio-cells' + - gpio-ranges + - interrupt-controller + - '#interrupt-cells' + +if: + not: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen1-gpio +then: + required: + - clocks + - power-domains + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a77470-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a77470-sysc.h> + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a77470", "renesas,rcar-gen2-gpio"; + reg = <0xe6053000 0x50>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 909>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 909>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 96 30>; + gpio-reserved-ranges = <17 10>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/rockchip,gpio-bank.yaml b/Documentation/devicetree/bindings/gpio/rockchip,gpio-bank.yaml new file mode 100644 index 000000000..affd823c8 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/rockchip,gpio-bank.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/rockchip,gpio-bank.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip GPIO bank + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,gpio-bank + - rockchip,rk3188-gpio-bank0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: APB interface clock source + - description: GPIO debounce reference clock source + + gpio-ranges: true + + gpio-controller: true + + gpio-line-names: true + + "#gpio-cells": + const: 2 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - gpio-controller + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl: pinctrl { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio@2000a000 { + compatible = "rockchip,rk3188-gpio-bank0"; + reg = <0x2000a000 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 9>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@2003c000 { + compatible = "rockchip,gpio-bank"; + reg = <0x2003c000 0x100>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 10>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml b/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml new file mode 100644 index 000000000..d8cce73ea --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/rockchip,rk3328-grf-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip RK3328 General Register Files GPIO controller + +description: + The Rockchip RK3328 General Register File (GRF) outputs only the + GPIO_MUTE pin, originally for codec mute control, but it can also be used + for general purpose. It is manipulated by the GRF_SOC_CON10 register. + If needed in the future support for the HDMI pins can also be added. + The GPIO node should be declared as the child of the GRF node. + + The GPIO_MUTE pin is referred to in the format + + <&grf_gpio 0 GPIO_ACTIVE_LOW> + + The first cell is the pin number and + the second cell is used to specify the GPIO polarity + 0 = Active high + 1 = Active low + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + const: rockchip,rk3328-grf-gpio + + gpio-controller: true + + "#gpio-cells": + const: 2 + +required: + - compatible + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + grf_gpio: gpio { + compatible = "rockchip,rk3328-grf-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml b/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml new file mode 100644 index 000000000..fc095646a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sifive,gpio.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/sifive,gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive GPIO controller + +maintainers: + - Paul Walmsley <paul.walmsley@sifive.com> + +properties: + compatible: + items: + - enum: + - sifive,fu540-c000-gpio + - sifive,fu740-c000-gpio + - canaan,k210-gpiohs + - const: sifive,gpio0 + + reg: + maxItems: 1 + + interrupts: + description: + Interrupt mapping, one per GPIO. Maximum 32 GPIOs. + minItems: 1 + maxItems: 32 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + "#gpio-cells": + const: 2 + + ngpios: + description: + The number of GPIOs available on the controller implementation. + It is 16 for the SiFive SoCs and 32 for the Canaan K210. + minimum: 1 + maximum: 32 + default: 16 + + gpio-line-names: + minItems: 1 + maxItems: 32 + + gpio-controller: true + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - "#gpio-cells" + - gpio-controller + +if: + properties: + compatible: + contains: + enum: + - sifive,fu540-c000-gpio + - sifive,fu740-c000-gpio +then: + required: + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sifive-fu540-prci.h> + gpio@10060000 { + compatible = "sifive,fu540-c000-gpio", "sifive,gpio0"; + interrupt-parent = <&plic>; + interrupts = <7>, <8>, <9>, <10>, <11>, <12>, <13>, <14>, <15>, <16>, + <17>, <18>, <19>, <20>, <21>, <22>; + reg = <0x10060000 0x1000>; + clocks = <&tlclk FU540_PRCI_CLK_TLCLK>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt new file mode 100644 index 000000000..1b30812b0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt @@ -0,0 +1,21 @@ +Synopsys GPIO via CREG (Control REGisters) driver + +Required properties: +- compatible : "snps,creg-gpio-hsdk" or "snps,creg-gpio-axs10x". +- reg : Exactly one register range with length 0x4. +- #gpio-cells : Since the generic GPIO binding is used, the + amount of cells must be specified as 2. The first cell is the + pin number, the second cell is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- gpio-controller : Marks the device node as a GPIO controller. +- ngpios: Number of GPIO pins. + +Example: + +gpio: gpio@f00014b0 { + compatible = "snps,creg-gpio-hsdk"; + reg = <0xf00014b0 0x4>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml b/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml new file mode 100644 index 000000000..b391cc1b4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps,dw-apb-gpio.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/snps,dw-apb-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare APB GPIO controller + +description: | + Synopsys DesignWare GPIO controllers have a configurable number of ports, + each of which are intended to be represented as child nodes with the generic + GPIO-controller properties as desribed in this bindings file. + +maintainers: + - Hoan Tran <hoan@os.amperecomputing.com> + - Serge Semin <fancer.lancer@gmail.com> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: snps,dw-apb-gpio + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: APB interface clock source + - description: DW GPIO debounce reference clock source + + clock-names: + minItems: 1 + items: + - const: bus + - const: db + + resets: + maxItems: 1 + +patternProperties: + "^gpio-(port|controller)@[0-9a-f]+$": + type: object + properties: + compatible: + const: snps,dw-apb-gpio-port + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + ngpios: + default: 32 + minimum: 1 + maximum: 32 + + snps,nr-gpios: + description: The number of GPIO pins exported by the port. + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + default: 32 + minimum: 1 + maximum: 32 + + interrupts: + description: | + The interrupts to the parent controller raised when GPIOs generate + the interrupts. If the controller provides one combined interrupt + for all GPIOs, specify a single interrupt. If the controller provides + one interrupt for each GPIO, provide a list of interrupts that + correspond to each of the GPIO pins. + minItems: 1 + maxItems: 32 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + + dependencies: + interrupt-controller: [ interrupts ] + + additionalProperties: false + +additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +examples: + - | + gpio: gpio@20000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x20000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-port@0 { + compatible = "snps,dw-apb-gpio-port"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&vic1>; + interrupts = <0>; + }; + + portb: gpio-port@1 { + compatible = "snps,dw-apb-gpio-port"; + reg = <1>; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml b/Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml new file mode 100644 index 000000000..228fa27ff --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/socionext,uniphier-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier GPIO controller + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: socionext,uniphier-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + interrupt-controller: true + + "#interrupt-cells": + description: | + The first cell defines the interrupt number. + The second cell bits[3:0] is used to specify trigger type as follows: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + Valid combinations are 1, 2, 3, 4, 8. + const: 2 + + ngpios: + minimum: 0 + maximum: 512 + + gpio-ranges: true + + gpio-ranges-group-names: true + + socionext,interrupt-ranges: + description: | + Specifies an interrupt number mapping between this GPIO controller and + its interrupt parent, in the form of arbitrary number of + <child-interrupt-base parent-interrupt-base length> triplets. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + +patternProperties: + "^.+-hog(-[0-9]+)?$": + type: object + properties: + gpio-hog: true + gpios: true + input: true + output-high: true + output-low: true + line-name: true + + required: + - gpio-hog + - gpios + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + - ngpios + - gpio-ranges + - socionext,interrupt-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/gpio/uniphier-gpio.h> + + gpio: gpio@55000000 { + compatible = "socionext,uniphier-gpio"; + reg = <0x55000000 0x200>; + interrupt-parent = <&aidet>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 0>; + gpio-ranges-group-names = "gpio_range"; + ngpios = <248>; + socionext,interrupt-ranges = <0 48 16>, <16 154 5>, <21 217 3>; + }; + + // Consumer: + // Please note UNIPHIER_GPIO_PORT(29, 4) represents PORT294 in the SoC + // document. Unfortunately, only the one's place is octal in the port + // numbering. (That is, PORT 8, 9, 18, 19, 28, 29, ... do not exist.) + // UNIPHIER_GPIO_PORT() is a helper macro to calculate 29 * 8 + 4. + sdhci0_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio UNIPHIER_GPIO_PORT(29, 4) GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt new file mode 100644 index 000000000..563eff22b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sodaville.txt @@ -0,0 +1,48 @@ +GPIO controller on CE4100 / Sodaville SoCs +========================================== + +The bindings for CE4100's GPIO controller match the generic description +which is covered by the gpio.txt file in this folder. + +The only additional property is the intel,muxctl property which holds the +value which is written into the MUXCNTL register. + +There is no compatible property for now because the driver is probed via +PCI id (vendor 0x8086 device 0x2e67). + +The interrupt specifier consists of two cells encoded as follows: + - <1st cell>: The interrupt-number that identifies the interrupt source. + - <2nd cell>: The level-sense information, encoded as follows: + 4 - active high level-sensitive + 8 - active low level-sensitive + +Example of the GPIO device and one user: + + pcigpio: gpio@b,1 { + /* two cells for GPIO and interrupt */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "pci8086,2e67.2", + "pci8086,2e67", + "pciclassff0000", + "pciclassff00"; + + reg = <0x15900 0x0 0x0 0x0 0x0>; + /* Interrupt line of the gpio device */ + interrupts = <15 1>; + /* It is an interrupt and GPIO controller itself */ + interrupt-controller; + gpio-controller; + intel,muxctl = <0>; + }; + + testuser@20 { + compatible = "example,testuser"; + /* User the 11th GPIO line as an active high triggered + * level interrupt + */ + interrupts = <11 8>; + interrupt-parent = <&pcigpio>; + /* Use this GPIO also with the gpio functions */ + gpios = <&pcigpio 11 0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/spear_spics.txt b/Documentation/devicetree/bindings/gpio/spear_spics.txt new file mode 100644 index 000000000..dd04d96e6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -0,0 +1,49 @@ +=== ST Microelectronics SPEAr SPI CS Driver === + +SPEAr platform provides a provision to control chipselects of ARM PL022 Prime +Cell spi controller through its system registers, which otherwise remains under +PL022 control. If chipselect remain under PL022 control then they would be +released as soon as transfer is over and TxFIFO becomes empty. This is not +desired by some of the device protocols above spi which expect (multiple) +transfers without releasing their chipselects. + +Chipselects can be controlled by software by turning them as GPIOs. SPEAr +provides another interface through system registers through which software can +directly control each PL022 chipselect. Hence, it is natural for SPEAr to export +the control of this interface as gpio. + +Required properties: + + * compatible: should be defined as "st,spear-spics-gpio" + * reg: mentioning address range of spics controller + * st-spics,peripcfg-reg: peripheral configuration register offset + * st-spics,sw-enable-bit: bit offset to enable sw control + * st-spics,cs-value-bit: bit offset to drive chipselect low or high + * st-spics,cs-enable-mask: chip select number bit mask + * st-spics,cs-enable-shift: chip select number program offset + * gpio-controller: Marks the device node as gpio controller + * #gpio-cells: should be 1 and will mention chip select number + +All the above bit offsets are within peripcfg register. + +Example: +------- +spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; +}; + + +spi0: spi@e0100000 { + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, + <&spics 1>; + ... +} diff --git a/Documentation/devicetree/bindings/gpio/ti,omap-gpio.yaml b/Documentation/devicetree/bindings/gpio/ti,omap-gpio.yaml new file mode 100644 index 000000000..7087e4a50 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ti,omap-gpio.yaml @@ -0,0 +1,108 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/ti,omap-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OMAP GPIO controller bindings + +maintainers: + - Grygorii Strashko <grygorii.strashko@ti.com> + +description: | + The general-purpose interface combines general-purpose input/output (GPIO) banks. + Each GPIO banks provides up to 32 dedicated general-purpose pins with input + and output capabilities; interrupt generation in active mode and wake-up + request generation in idle mode upon the detection of external events. + +properties: + compatible: + oneOf: + - enum: + - ti,omap2-gpio + - ti,omap3-gpio + - ti,omap4-gpio + - items: + - const: ti,am4372-gpio + - const: ti,omap4-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + maxItems: 1 + + gpio-ranges: true + + gpio-line-names: + minItems: 1 + maxItems: 32 + + ti,gpio-always-on: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if a GPIO bank is always powered and will never lose its logic state. + + ti,hwmods: + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + description: + Name of the hwmod associated with the GPIO. Needed on some legacy OMAP + SoCs which have not been converted to the ti,sysc interconnect hierarachy. + + ti,no-reset-on-init: + $ref: /schemas/types.yaml#/definitions/flag + deprecated: true + description: + Do not reset on init. Used with ti,hwmods on some legacy OMAP SoCs which + have not been converted to the ti,sysc interconnect hierarachy. + +patternProperties: + "^(.+-hog(-[0-9]+)?)$": + type: object + + required: + - gpio-hog + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + gpio0: gpio@0 { + compatible = "ti,omap4-gpio"; + reg = <0x0 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <96>; + ti,gpio-always-on; + + ls-buf-en-hog { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml b/Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml new file mode 100644 index 000000000..b085450b5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/toshiba,gpio-visconti.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toshiba Visconti ARM SoCs GPIO controller + +maintainers: + - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> + +properties: + compatible: + items: + - const: toshiba,gpio-tmpv7708 + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-ranges: true + + gpio-controller: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + description: + interrupt mapping one per GPIO. + minItems: 16 + maxItems: 16 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-ranges + - gpio-controller + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + gpio: gpio@28020000 { + compatible = "toshiba,gpio-tmpv7708"; + reg = <0 0x28020000 0 0x1000>; + #gpio-cells = <0x2>; + gpio-ranges = <&pmux 0 0 32>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt new file mode 100644 index 000000000..038c3a6a1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt @@ -0,0 +1,38 @@ +Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers. + +The Western Digital MyBook Live has two memory-mapped GPIO controllers. +Both GPIO controller only have a single 8-bit data register, where GPIO +state can be read and/or written. + +Required properties: + - compatible: should be "wd,mbl-gpio" + - reg-names: must contain + "dat" - data register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - no-output: GPIOs are read-only. + +Examples: + gpio0: gpio0@e0000000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0000000 0x1>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio1: gpio1@e0100000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0100000 0x1>; + #gpio-cells = <2>; + gpio-controller; + no-output; + }; diff --git a/Documentation/devicetree/bindings/gpio/x-powers,axp209-gpio.yaml b/Documentation/devicetree/bindings/gpio/x-powers,axp209-gpio.yaml new file mode 100644 index 000000000..7f26f6b1e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/x-powers,axp209-gpio.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/gpio/x-powers,axp209-gpio.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: X-Powers AXP209 GPIO + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + +properties: + "#gpio-cells": + const: 2 + description: > + The first cell is the pin number and the second is the GPIO flags. + + compatible: + oneOf: + - enum: + - x-powers,axp209-gpio + - x-powers,axp221-gpio + - x-powers,axp813-gpio + - items: + - enum: + - x-powers,axp223-gpio + - x-powers,axp809-gpio + - const: x-powers,axp221-gpio + - items: + - const: x-powers,axp803-gpio + - const: x-powers,axp813-gpio + + gpio-controller: true + +patternProperties: + "^.*-pins?$": + $ref: /schemas/pinctrl/pinmux-node.yaml# + + properties: + pins: + items: + enum: + - GPIO0 + - GPIO1 + - GPIO2 + + function: + enum: + - adc + - ldo + - gpio_in + - gpio_out + +required: + - compatible + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml b/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml new file mode 100644 index 000000000..11ae8ec3c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/xlnx,gpio-xilinx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx AXI GPIO controller + +maintainers: + - Neeli Srinivas <srinivas.neeli@xilinx.com> + +description: + The AXI GPIO design provides a general purpose input/output interface + to an AXI4-Lite interface. The AXI GPIO can be configured as either + a single or a dual-channel device. The width of each channel is + independently configurable. The channels can be configured to + generate an interrupt when a transition on any of their inputs occurs. + +properties: + compatible: + enum: + - xlnx,xps-gpio-1.00.a + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + interrupts: + maxItems: 1 + + gpio-controller: true + + gpio-line-names: + description: strings describing the names of each gpio line + minItems: 1 + maxItems: 64 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + interrupt-names: true + + xlnx,all-inputs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This option sets this GPIO channel1 bits in input mode. + + xlnx,all-inputs-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This option sets this GPIO channel2 bits in input mode. + + xlnx,all-outputs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This option sets this GPIO channel1 bits in output mode. + + xlnx,all-outputs-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This option sets this GPIO channel2 bits in output mode. + + xlnx,dout-default: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Sets the default value of all the enabled bits of + channel1. + default: 0 + + xlnx,dout-default-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Sets the default value of all the enabled bits of + channel2. + default: 0 + + xlnx,gpio-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The value defines the bit width of the GPIO channel1. + minimum: 1 + maximum: 32 + default: 32 + + xlnx,gpio2-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The value defines the bit width of the GPIO channel2. + minimum: 1 + maximum: 32 + default: 32 + + xlnx,interrupt-present: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This parameter enables interrupt control logic + and interrupt registers in GPIO module. + minimum: 0 + maximum: 1 + default: 0 + + xlnx,is-dual: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This parameter enables a second GPIO channel (GPIO2). + minimum: 0 + maximum: 1 + default: 0 + + xlnx,tri-default: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This value configures the input or output mode + of each bit of GPIO channel1. + + xlnx,tri-default-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This value configures the input or output mode + of each bit of GPIO channel2. + +required: + - reg + - compatible + - gpio-controller + - "#gpio-cells" + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + gpio@a0020000 { + compatible = "xlnx,xps-gpio-1.00.a"; + reg = <0xa0020000 0x10000>; + #gpio-cells = <2>; + #interrupt-cells = <0x2>; + clocks = <&zynqmp_clk 71>; + gpio-controller; + interrupt-controller; + interrupt-names = "ip2intc_irpt"; + interrupt-parent = <&gic>; + interrupts = <0 89 4>; + xlnx,all-inputs = <0x0>; + xlnx,all-inputs-2 = <0x0>; + xlnx,all-outputs = <0x0>; + xlnx,all-outputs-2 = <0x0>; + xlnx,dout-default = <0x0>; + xlnx,dout-default-2 = <0x0>; + xlnx,gpio-width = <0x20>; + xlnx,gpio2-width = <0x20>; + xlnx,interrupt-present = <0x1>; + xlnx,is-dual = <0x1>; + xlnx,tri-default = <0xFFFFFFFF>; + xlnx,tri-default-2 = <0xFFFFFFFF>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml new file mode 100644 index 000000000..31c0fc345 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/gpio/xlnx,zynqmp-gpio-modepin.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: ZynqMP Mode Pin GPIO controller + +description: + PS_MODE is 4-bits boot mode pins sampled on POR deassertion. Mode Pin + GPIO controller with configurable from numbers of pins (from 0 to 3 per + PS_MODE). Every pin can be configured as input/output. + +maintainers: + - Piyush Mehta <piyush.mehta@xilinx.com> + +properties: + compatible: + const: xlnx,zynqmp-gpio-modepin + + gpio-controller: true + + "#gpio-cells": + const: 2 + +required: + - compatible + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + zynqmp-firmware { + gpio { + compatible = "xlnx,zynqmp-gpio-modepin"; + gpio-controller; + #gpio-cells = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.yaml b/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.yaml new file mode 100644 index 000000000..a36aec270 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/xylon,logicvc-gpio.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 Bootlin +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/gpio/xylon,logicvc-gpio.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Xylon LogiCVC GPIO controller + +maintainers: + - Paul Kocialkowski <paul.kocialkowski@bootlin.com> + +description: | + The LogiCVC GPIO describes the GPIO block included in the LogiCVC display + controller. These are meant to be used for controlling display-related + signals. + + The controller exposes GPIOs from the display and power control registers, + which are mapped by the driver as follows: + - GPIO[4:0] (display control) mapped to index 0-4 + - EN_BLIGHT (power control) mapped to index 5 + - EN_VDD (power control) mapped to index 6 + - EN_VEE (power control) mapped to index 7 + - V_EN (power control) mapped to index 8 + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + enum: + - xylon,logicvc-3.02.a-gpio + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-line-names: + minItems: 1 + maxItems: 9 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + logicvc: logicvc@43c00000 { + compatible = "xylon,logicvc-3.02.a", "syscon", "simple-mfd"; + reg = <0x43c00000 0x6000>; + + #address-cells = <1>; + #size-cells = <1>; + + logicvc_gpio: gpio@40 { + compatible = "xylon,logicvc-3.02.a-gpio"; + reg = <0x40 0x40>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "GPIO0", "GPIO1", "GPIO2", "GPIO3", "GPIO4", + "EN_BLIGHT", "EN_VDD", "EN_VEE", "V_EN"; + }; + }; |