diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml | 107 |
1 files changed, 107 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml new file mode 100644 index 000000000..c99cc7323 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-intr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments K3 Interrupt Router + +maintainers: + - Lokesh Vutla <lokeshvutla@ti.com> + +allOf: + - $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml# + +description: | + The Interrupt Router (INTR) module provides a mechanism to mux M + interrupt inputs to N interrupt outputs, where all M inputs are selectable + to be driven per N output. An Interrupt Router can either handle edge + triggered or level triggered interrupts and that is fixed in hardware. + + Interrupt Router + +----------------------+ + | Inputs Outputs | + +-------+ | +------+ +-----+ | + | GPIO |----------->| | irq0 | | 0 | | Host IRQ + +-------+ | +------+ +-----+ | controller + | . . | +-------+ + +-------+ | . . |----->| IRQ | + | INTA |----------->| . . | +-------+ + +-------+ | . +-----+ | + | +------+ | N | | + | | irqM | +-----+ | + | +------+ | + | | + +----------------------+ + + There is one register per output (MUXCNTL_N) that controls the selection. + Configuration of these MUXCNTL_N registers is done by a system controller + (like the Device Memory and Security Controller on K3 AM654 SoC). System + controller will keep track of the used and unused registers within the Router. + Driver should request the system controller to get the range of GIC IRQs + assigned to the requesting hosts. It is the drivers responsibility to keep + track of Host IRQs. + + Communication between the host processor running an OS and the system + controller happens through a protocol called TI System Control Interface + (TISCI protocol). + +properties: + compatible: + const: ti,sci-intr + + ti,intr-trigger-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 4] + description: | + Should be one of the following. + 1 = If intr supports edge triggered interrupts. + 4 = If intr supports level triggered interrupts. + + reg: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 1 + description: | + The 1st cell should contain interrupt router input hw number. + + ti,interrupt-ranges: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + Interrupt ranges that converts the INTR output hw irq numbers + to parents's input interrupt numbers. + items: + items: + - description: | + "output_irq" specifies the base for intr output irq + - description: | + "parent's input irq" specifies the base for parent irq + - description: | + "limit" specifies the limit for translation + +required: + - compatible + - ti,intr-trigger-type + - interrupt-controller + - '#interrupt-cells' + - ti,sci + - ti,sci-dev-id + - ti,interrupt-ranges + +unevaluatedProperties: false + +examples: + - | + main_gpio_intr: interrupt-controller0 { + compatible = "ti,sci-intr"; + ti,intr-trigger-type = <1>; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <1>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <131>; + ti,interrupt-ranges = <0 360 32>; + }; |