diff options
Diffstat (limited to '')
45 files changed, 6453 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt new file mode 100644 index 000000000..22b77ee02 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt @@ -0,0 +1,127 @@ +* Device tree bindings for ARM PL172/PL175/PL176 MultiPort Memory Controller + +Required properties: + +- compatible: Must be "arm,primecell" and exactly one from + "arm,pl172", "arm,pl175" or "arm,pl176". + +- reg: Must contains offset/length value for controller. + +- #address-cells: Must be 2. The partition number has to be encoded in the + first address cell and it may accept values 0..N-1 + (N - total number of partitions). The second cell is the + offset into the partition. + +- #size-cells: Must be set to 1. + +- ranges: Must contain one or more chip select memory regions. + +- clocks: Must contain references to controller clocks. + +- clock-names: Must contain "mpmcclk" and "apb_pclk". + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + See clock-bindings.txt + +Child chip-select (cs) nodes contain the memory devices nodes connected to +such as NOR (e.g. cfi-flash) and NAND. + +Required child cs node properties: + +- #address-cells: Must be 2. + +- #size-cells: Must be 1. + +- ranges: Empty property indicating that child nodes can inherit + memory layout. + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + +- mpmc,cs: Chip select number. Indicates to the pl0172 driver + which chipselect is used for accessing the memory. + +- mpmc,memory-width: Width of the chip select memory. Must be equal to + either 8, 16 or 32. + +Optional child cs node config properties: + +- mpmc,async-page-mode: Enable asynchronous page mode. + +- mpmc,cs-active-high: Set chip select polarity to active high. + +- mpmc,byte-lane-low: Set byte lane state to low. + +- mpmc,extended-wait: Enable extended wait. + +- mpmc,buffer-enable: Enable write buffer, option is not supported by + PL175 and PL176 controllers. + +- mpmc,write-protect: Enable write protect. + +Optional child cs node timing properties: + +- mpmc,write-enable-delay: Delay from chip select assertion to write + enable (WE signal) in nano seconds. + +- mpmc,output-enable-delay: Delay from chip select assertion to output + enable (OE signal) in nano seconds. + +- mpmc,write-access-delay: Delay from chip select assertion to write + access in nano seconds. + +- mpmc,read-access-delay: Delay from chip select assertion to read + access in nano seconds. + +- mpmc,page-mode-read-delay: Delay for asynchronous page mode sequential + accesses in nano seconds. + +- mpmc,turn-round-delay: Delay between access to memory banks in nano + seconds. + +If any of the above timing parameters are absent, current parameter value will +be taken from the corresponding HW reg. + +Example for pl172 with nor flash on chip select 0 shown below. + +emc: memory-controller@40005000 { + compatible = "arm,pl172", "arm,primecell"; + reg = <0x40005000 0x1000>; + clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>; + clock-names = "mpmcclk", "apb_pclk"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x1c000000 0x1000000 + 1 0 0x1d000000 0x1000000 + 2 0 0x1e000000 0x1000000 + 3 0 0x1f000000 0x1000000>; + + cs0 { + #address-cells = <2>; + #size-cells = <1>; + ranges; + + mpmc,cs = <0>; + mpmc,memory-width = <16>; + mpmc,byte-lane-low; + mpmc,write-enable-delay = <0>; + mpmc,output-enable-delay = <0>; + mpmc,read-enable-delay = <70>; + mpmc,page-mode-read-delay = <70>; + + flash@0,0 { + compatible = "sst,sst39vf320", "cfi-flash"; + reg = <0 0 0x400000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "data"; + reg = <0 0x400000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml b/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml new file mode 100644 index 000000000..01c9acf92 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl353-smc.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/arm,pl353-smc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL353 Static Memory Controller (SMC) device-tree bindings + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + - Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> + +description: + The PL353 Static Memory Controller is a bus where you can connect two kinds + of memory interfaces, which are NAND and memory mapped interfaces (such as + SRAM or NOR). + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl353-smc-r2p1 + required: + - compatible + +properties: + $nodename: + pattern: "^memory-controller@[0-9a-f]+$" + + compatible: + items: + - const: arm,pl353-smc-r2p1 + - const: arm,primecell + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + reg: + items: + - description: + Configuration registers for the host and sub-controllers. + The three chip select regions are defined in 'ranges'. + + clocks: + items: + - description: clock for the memory device bus + - description: main clock of the SMC + + clock-names: + items: + - const: memclk + - const: apb_pclk + + ranges: + minItems: 1 + description: | + Memory bus areas for interacting with the devices. Reflects + the memory layout with four integer values following: + <cs-number> 0 <offset> <size> + items: + - description: NAND bank 0 + - description: NOR/SRAM bank 0 + - description: NOR/SRAM bank 1 + + interrupts: true + +patternProperties: + "@[0-3],[a-f0-9]+$": + type: object + description: | + The child device node represents the controller connected to the SMC + bus. The controller can be a NAND controller or a pair of any memory + mapped controllers such as NOR and SRAM controllers. + + properties: + compatible: + description: + Compatible of memory controller. + + reg: + items: + - items: + - description: | + Chip-select ID, as in the parent range property. + minimum: 0 + maximum: 2 + - description: | + Offset of the memory region requested by the device. + - description: | + Length of the memory region requested by the device. + + required: + - compatible + - reg + +required: + - compatible + - reg + - clock-names + - clocks + - "#address-cells" + - "#size-cells" + - ranges + +additionalProperties: false + +examples: + - | + smcc: memory-controller@e000e000 { + compatible = "arm,pl353-smc-r2p1", "arm,primecell"; + reg = <0xe000e000 0x0001000>; + clock-names = "memclk", "apb_pclk"; + clocks = <&clkc 11>, <&clkc 44>; + ranges = <0x0 0x0 0xe1000000 0x1000000 /* Nand CS region */ + 0x1 0x0 0xe2000000 0x2000000 /* SRAM/NOR CS0 region */ + 0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */ + #address-cells = <2>; + #size-cells = <1>; + + nfc0: nand-controller@0,0 { + compatible = "arm,pl353-nand-r2p1"; + reg = <0 0 0x1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt new file mode 100644 index 000000000..94bf7896a --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt @@ -0,0 +1,137 @@ +* Device tree bindings for Atmel EBI + +The External Bus Interface (EBI) controller is a bus where you can connect +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs). +The EBI provides a glue-less interface to asynchronous memories through the SMC +(Static Memory Controller). + +Required properties: + +- compatible: "atmel,at91sam9260-ebi" + "atmel,at91sam9261-ebi" + "atmel,at91sam9263-ebi0" + "atmel,at91sam9263-ebi1" + "atmel,at91sam9rl-ebi" + "atmel,at91sam9g45-ebi" + "atmel,at91sam9x5-ebi" + "atmel,sama5d3-ebi" + "microchip,sam9x60-ebi" + +- reg: Contains offset/length value for EBI memory mapping. + This property might contain several entries if the EBI + memory range is not contiguous + +- #address-cells: Must be 2. + The first cell encodes the CS. + The second cell encode the offset into the CS memory + range. + +- #size-cells: Must be set to 1. + +- ranges: Encodes CS to memory region association. + +- clocks: Clock feeding the EBI controller. + See clock-bindings.txt + +Children device nodes are representing device connected to the EBI bus. + +Required device node properties: + +- reg: Contains the chip-select id, the offset and the length + of the memory region requested by the device. + +EBI bus configuration will be defined directly in the device subnode. + +Optional EBI/SMC properties: + +- atmel,smc-bus-width: width of the asynchronous device's data bus + 8, 16 or 32. + Default to 8 when undefined. + +- atmel,smc-byte-access-type "write" or "select" (see Atmel datasheet). + Default to "select" when undefined. + +- atmel,smc-read-mode "nrd" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-write-mode "nwe" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-exnw-mode "disabled", "frozen" or "ready". + Default to "disabled" when undefined. + +- atmel,smc-page-mode enable page mode if present. The provided value + defines the page size (supported values: 4, 8, + 16 and 32). + +- atmel,smc-tdf-mode: "normal" or "optimized". When set to + "optimized" the data float time is optimized + depending on the next device being accessed + (next device setup time is subtracted to the + current device data float time). + Default to "normal" when undefined. + +If at least one atmel,smc- property is defined the following SMC timing +properties become mandatory. In the other hand, if none of the atmel,smc- +properties are specified, we assume that the EBI bus configuration will be +handled by the sub-device driver, and none of those properties should be +defined. + +All the timings are expressed in nanoseconds (see Atmel datasheet for a full +description). + +- atmel,smc-ncs-rd-setup-ns +- atmel,smc-nrd-setup-ns +- atmel,smc-ncs-wr-setup-ns +- atmel,smc-nwe-setup-ns +- atmel,smc-ncs-rd-pulse-ns +- atmel,smc-nrd-pulse-ns +- atmel,smc-ncs-wr-pulse-ns +- atmel,smc-nwe-pulse-ns +- atmel,smc-nwe-cycle-ns +- atmel,smc-nrd-cycle-ns +- atmel,smc-tdf-ns + +Example: + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + atmel,matrix = <&matrix>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ebi_addr>; + + nor: flash@0,0 { + compatible = "cfi-flash"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x1000000>; + bank-width = <2>; + + atmel,smc-read-mode = "nrd"; + atmel,smc-write-mode = "nwe"; + atmel,smc-bus-width = <16>; + atmel,smc-ncs-rd-setup-ns = <0>; + atmel,smc-ncs-wr-setup-ns = <0>; + atmel,smc-nwe-setup-ns = <8>; + atmel,smc-nrd-setup-ns = <16>; + atmel,smc-ncs-rd-pulse-ns = <84>; + atmel,smc-ncs-wr-pulse-ns = <84>; + atmel,smc-nrd-pulse-ns = <76>; + atmel,smc-nwe-pulse-ns = <76>; + atmel,smc-nrd-cycle-ns = <107>; + atmel,smc-nwe-cycle-ns = <84>; + atmel,smc-tdf-ns = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/memory-controllers/baikal,bt1-l2-ctl.yaml b/Documentation/devicetree/bindings/memory-controllers/baikal,bt1-l2-ctl.yaml new file mode 100644 index 000000000..1fca282f6 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/baikal,bt1-l2-ctl.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/baikal,bt1-l2-ctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 L2-cache Control Block + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: | + By means of the System Controller Baikal-T1 SoC exposes a few settings to + tune the MIPS P5600 CM2 L2 cache performance up. In particular it's possible + to change the Tag, Data and Way-select RAM access latencies. Baikal-T1 + L2-cache controller block is responsible for the tuning. Its DT node is + supposed to be a child of the system controller. + +properties: + compatible: + const: baikal,bt1-l2-ctl + + reg: + maxItems: 1 + + baikal,l2-ws-latency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Cycles of latency for Way-select RAM accesses + default: 0 + minimum: 0 + maximum: 3 + + baikal,l2-tag-latency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Cycles of latency for Tag RAM accesses + default: 0 + minimum: 0 + maximum: 3 + + baikal,l2-data-latency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Cycles of latency for Data RAM accesses + default: 1 + minimum: 0 + maximum: 3 + +additionalProperties: false + +required: + - compatible + +examples: + - | + l2@1f04d028 { + compatible = "baikal,bt1-l2-ctl"; + reg = <0x1f04d028 0x004>; + + baikal,l2-ws-latency = <1>; + baikal,l2-tag-latency = <1>; + baikal,l2-data-latency = <2>; + }; +... diff --git a/Documentation/devicetree/bindings/memory-controllers/brcm,brcmstb-memc-ddr.yaml b/Documentation/devicetree/bindings/memory-controllers/brcm,brcmstb-memc-ddr.yaml new file mode 100644 index 000000000..4b072c879 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/brcm,brcmstb-memc-ddr.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/brcm,brcmstb-memc-ddr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Memory controller (MEMC) for Broadcom STB + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + compatible: + items: + - enum: + - brcm,brcmstb-memc-ddr-rev-b.1.x + - brcm,brcmstb-memc-ddr-rev-b.2.0 + - brcm,brcmstb-memc-ddr-rev-b.2.1 + - brcm,brcmstb-memc-ddr-rev-b.2.2 + - brcm,brcmstb-memc-ddr-rev-b.2.3 + - brcm,brcmstb-memc-ddr-rev-b.2.5 + - brcm,brcmstb-memc-ddr-rev-b.2.6 + - brcm,brcmstb-memc-ddr-rev-b.2.7 + - brcm,brcmstb-memc-ddr-rev-b.2.8 + - brcm,brcmstb-memc-ddr-rev-b.3.0 + - brcm,brcmstb-memc-ddr-rev-b.3.1 + - brcm,brcmstb-memc-ddr-rev-c.1.0 + - brcm,brcmstb-memc-ddr-rev-c.1.1 + - brcm,brcmstb-memc-ddr-rev-c.1.2 + - brcm,brcmstb-memc-ddr-rev-c.1.3 + - brcm,brcmstb-memc-ddr-rev-c.1.4 + - const: brcm,brcmstb-memc-ddr + + reg: + maxItems: 1 + + clock-frequency: + description: DDR PHY frequency in Hz + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + memory-controller@9902000 { + compatible = "brcm,brcmstb-memc-ddr-rev-c.1.1", "brcm,brcmstb-memc-ddr"; + reg = <0x9902000 0x600>; + clock-frequency = <2133000000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.yaml b/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.yaml new file mode 100644 index 000000000..08cbdcddf --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/brcm,dpfe-cpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: DDR PHY Front End (DPFE) for Broadcom STB + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Markus Mayer <mmayer@broadcom.com> + +properties: + compatible: + items: + - enum: + - brcm,bcm7271-dpfe-cpu + - brcm,bcm7268-dpfe-cpu + - const: brcm,dpfe-cpu + + reg: + items: + - description: DCPU register space + - description: DCPU data memory space + - description: DCPU instruction memory space + + reg-names: + items: + - const: dpfe-cpu + - const: dpfe-dmem + - const: dpfe-imem + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +examples: + - | + dpfe-cpu@f1132000 { + compatible = "brcm,bcm7271-dpfe-cpu", "brcm,dpfe-cpu"; + reg = <0xf1132000 0x180>, + <0xf1134000 0x1000>, + <0xf1138000 0x4000>; + reg-names = "dpfe-cpu", "dpfe-dmem", "dpfe-imem"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml b/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml new file mode 100644 index 000000000..96d563fd6 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/calxeda-ddr-ctrlr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Calxeda DDR memory controller binding + +description: | + The Calxeda DDR memory controller is initialised and programmed by the + firmware, but an OS might want to read its registers for error reporting + purposes and to learn about the DRAM topology. + +maintainers: + - Andre Przywara <andre.przywara@arm.com> + +properties: + compatible: + enum: + - calxeda,hb-ddr-ctrl + - calxeda,ecx-2000-ddr-ctrl + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + memory-controller@fff00000 { + compatible = "calxeda,hb-ddr-ctrl"; + reg = <0xfff00000 0x1000>; + interrupts = <0 91 4>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/canaan,k210-sram.yaml b/Documentation/devicetree/bindings/memory-controllers/canaan,k210-sram.yaml new file mode 100644 index 000000000..f81fb866e --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/canaan,k210-sram.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/canaan,k210-sram.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Canaan K210 SRAM memory controller + +description: + The Canaan K210 SRAM memory controller is responsible for the system's 8 MiB + of SRAM. The controller is initialised by the bootloader, which configures + its clocks, before OS bringup. + +maintainers: + - Conor Dooley <conor@kernel.org> + +properties: + compatible: + enum: + - canaan,k210-sram + + clocks: + minItems: 1 + items: + - description: sram0 clock + - description: sram1 clock + - description: aisram clock + + clock-names: + minItems: 1 + items: + - const: sram0 + - const: sram1 + - const: aisram + +required: + - compatible + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/k210-clk.h> + memory-controller { + compatible = "canaan,k210-sram"; + clocks = <&sysclk K210_CLK_SRAM0>, + <&sysclk K210_CLK_SRAM1>, + <&sysclk K210_CLK_AI>; + clock-names = "sram0", "sram1", "aisram"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml new file mode 100644 index 000000000..1daa66592 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2-timings.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr2-timings.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LPDDR2 SDRAM AC timing parameters for a given speed-bin + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: jedec,lpddr2-timings + + max-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Maximum DDR clock frequency for the speed-bin, in Hz. + + min-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Minimum DDR clock frequency for the speed-bin, in Hz. + + tCKESR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + CKE minimum pulse width during SELF REFRESH (low pulse width during + SELF REFRESH) in pico seconds. + + tDQSCK-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + DQS output data access time from CK_t/CK_c in pico seconds. + + tDQSCK-max-derated: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + DQS output data access time from CK_t/CK_c, temperature de-rated, in pico + seconds. + + tFAW: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Four-bank activate window in pico seconds. + + tRAS-max-ns: + description: | + Row active time in nano seconds. + + tRAS-min: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Row active time in pico seconds. + + tRCD: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + RAS-to-CAS delay in pico seconds. + + tRPab: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Row precharge time (all banks) in pico seconds. + + tRRD: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Active bank A to active bank B in pico seconds. + + tRTP: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Internal READ to PRECHARGE command delay in pico seconds. + + tWR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + WRITE recovery time in pico seconds. + + tWTR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Internal WRITE-to-READ command delay in pico seconds. + + tXP: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Exit power-down to next valid command delay in pico seconds. + + tZQCL: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Long calibration time in pico seconds. + + tZQCS: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Short calibration time in pico seconds. + + tZQinit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Initialization calibration time in pico seconds. + +required: + - compatible + - min-freq + - max-freq + +additionalProperties: false + +examples: + - | + timings { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tRAS-max-ns = <70000>; + tRAS-min = <42000>; + tRPab = <21000>; + tRCD = <18000>; + tRRD = <10000>; + tRTP = <7500>; + tWR = <15000>; + tWTR = <7500>; + tXP = <7500>; + tZQCL = <360000>; + tZQCS = <90000>; + tZQinit = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml new file mode 100644 index 000000000..9d78f1406 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr2.yaml @@ -0,0 +1,234 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LPDDR2 SDRAM compliant to JEDEC JESD209-2 + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + oneOf: + - items: + - enum: + - elpida,ECB240ABACN + - elpida,B8132B2PB-6D-F + - enum: + - jedec,lpddr2-s4 + - items: + - enum: + - jedec,lpddr2-s2 + - items: + - enum: + - jedec,lpddr2-nvm + + revision-id1: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 255 + description: | + Revision 1 value of SDRAM chip. Obtained from device datasheet. + Property is deprecated, use revision-id instead. + deprecated: true + + revision-id2: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 255 + description: | + Revision 2 value of SDRAM chip. Obtained from device datasheet. + Property is deprecated, use revision-id instead. + deprecated: true + + revision-id: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Revision IDs read from Mode Register 6 and 7. One byte per uint32 cell (i.e. <MR6 MR7>). + minItems: 2 + maxItems: 2 + items: + minimum: 0 + maximum: 255 + + density: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Density in megabits of SDRAM chip. Obtained from device datasheet. + enum: + - 64 + - 128 + - 256 + - 512 + - 1024 + - 2048 + - 4096 + - 8192 + - 16384 + - 32768 + + io-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + IO bus width in bits of SDRAM chip. Obtained from device datasheet. + enum: + - 32 + - 16 + - 8 + + tRRD-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Active bank a to active bank b in terms of number of clock cycles. + Obtained from device datasheet. + + tWTR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Internal WRITE-to-READ command delay in terms of number of clock cycles. + Obtained from device datasheet. + + tXP-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Exit power-down to next valid command delay in terms of number of clock + cycles. Obtained from device datasheet. + + tRTP-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Internal READ to PRECHARGE command delay in terms of number of clock + cycles. Obtained from device datasheet. + + tCKE-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + CKE minimum pulse width (HIGH and LOW pulse width) in terms of number + of clock cycles. Obtained from device datasheet. + + tRPab-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Row precharge time (all banks) in terms of number of clock cycles. + Obtained from device datasheet. + + tRCD-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + RAS-to-CAS delay in terms of number of clock cycles. Obtained from + device datasheet. + + tWR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + WRITE recovery time in terms of number of clock cycles. Obtained from + device datasheet. + + tRASmin-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Row active time in terms of number of clock cycles. Obtained from device + datasheet. + + tCKESR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + CKE minimum pulse width during SELF REFRESH (low pulse width during + SELF REFRESH) in terms of number of clock cycles. Obtained from device + datasheet. + + tFAW-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 16 + description: | + Four-bank activate window in terms of number of clock cycles. Obtained + from device datasheet. + +patternProperties: + "^lpddr2-timings": + $ref: jedec,lpddr2-timings.yaml + description: | + The lpddr2 node may have one or more child nodes of type "lpddr2-timings". + "lpddr2-timings" provides AC timing parameters of the device for + a given speed-bin. The user may provide the timings for as many + speed-bins as is required. + +required: + - compatible + - density + - io-width + +additionalProperties: false + +examples: + - | + elpida_ECB240ABACN: lpddr2 { + compatible = "elpida,ECB240ABACN", "jedec,lpddr2-s4"; + density = <2048>; + io-width = <32>; + revision-id = <1 0>; + + tRPab-min-tck = <3>; + tRCD-min-tck = <3>; + tWR-min-tck = <3>; + tRASmin-min-tck = <3>; + tRRD-min-tck = <2>; + tWTR-min-tck = <2>; + tXP-min-tck = <2>; + tRTP-min-tck = <2>; + tCKE-min-tck = <3>; + tCKESR-min-tck = <3>; + tFAW-min-tck = <8>; + + timings_elpida_ECB240ABACN_400mhz: lpddr2-timings0 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <7500>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + + timings_elpida_ECB240ABACN_200mhz: lpddr2-timings1 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <200000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <10000>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml new file mode 100644 index 000000000..5c6512c1e --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3-timings.yaml @@ -0,0 +1,157 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr3-timings.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LPDDR3 SDRAM AC timing parameters for a given speed-bin + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: jedec,lpddr3-timings + + reg: + maxItems: 1 + description: | + Maximum DDR clock frequency for the speed-bin, in Hz. + Property is deprecated, use max-freq. + deprecated: true + + max-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Maximum DDR clock frequency for the speed-bin, in Hz. + + min-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Minimum DDR clock frequency for the speed-bin, in Hz. + + tCKE: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + CKE minimum pulse width (HIGH and LOW pulse width) in pico seconds. + + tCKESR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + CKE minimum pulse width during SELF REFRESH (low pulse width during + SELF REFRESH) in pico seconds. + + tFAW: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Four-bank activate window in pico seconds. + + tMRD: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Mode register set command delay in pico seconds. + + tR2R-C2C: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Additional READ-to-READ delay in chip-to-chip cases in pico seconds. + + tRAS: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Row active time in pico seconds. + + tRC: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + ACTIVATE-to-ACTIVATE command period in pico seconds. + + tRCD: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + RAS-to-CAS delay in pico seconds. + + tRFC: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Refresh Cycle time in pico seconds. + + tRPab: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Row precharge time (all banks) in pico seconds. + + tRPpb: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Row precharge time (single banks) in pico seconds. + + tRRD: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Active bank A to active bank B in pico seconds. + + tRTP: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Internal READ to PRECHARGE command delay in pico seconds. + + tW2W-C2C: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Additional WRITE-to-WRITE delay in chip-to-chip cases in pico seconds. + + tWR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + WRITE recovery time in pico seconds. + + tWTR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Internal WRITE-to-READ command delay in pico seconds. + + tXP: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Exit power-down to next valid command delay in pico seconds. + + tXSR: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + SELF REFRESH exit to next valid command delay in pico seconds. + +required: + - compatible + - min-freq + - max-freq + +additionalProperties: false + +examples: + - | + lpddr3 { + timings { + compatible = "jedec,lpddr3-timings"; + max-freq = <800000000>; + min-freq = <100000000>; + tCKE = <3750>; + tCKESR = <3750>; + tFAW = <25000>; + tMRD = <7000>; + tR2R-C2C = <0>; + tRAS = <23000>; + tRC = <33750>; + tRCD = <10000>; + tRFC = <65000>; + tRPab = <12000>; + tRPpb = <12000>; + tRRD = <6000>; + tRTP = <3750>; + tW2W-C2C = <0>; + tWR = <7500>; + tWTR = <3750>; + tXP = <3750>; + tXSR = <70000>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml new file mode 100644 index 000000000..48908a194 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ddr/jedec,lpddr3.yaml @@ -0,0 +1,263 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ddr/jedec,lpddr3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LPDDR3 SDRAM compliant to JEDEC JESD209-3 + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + items: + - enum: + - samsung,K3QF2F20DB + - const: jedec,lpddr3 + + '#address-cells': + const: 1 + deprecated: true + + density: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Density in megabits of SDRAM chip. + enum: + - 4096 + - 8192 + - 16384 + - 32768 + + io-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + IO bus width in bits of SDRAM chip. + enum: + - 32 + - 16 + + manufacturer-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Manufacturer ID value read from Mode Register 5. The property is + deprecated, manufacturer should be derived from the compatible. + deprecated: true + + revision-id: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + items: + maximum: 255 + description: | + Revision value of SDRAM chip read from Mode Registers 6 and 7. + + '#size-cells': + const: 0 + deprecated: true + + tCKE-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + CKE minimum pulse width (HIGH and LOW pulse width) in terms of number + of clock cycles. + + tCKESR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + CKE minimum pulse width during SELF REFRESH (low pulse width during + SELF REFRESH) in terms of number of clock cycles. + + tDQSCK-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + DQS output data access time from CK_t/CK_c in terms of number of clock + cycles. + + tFAW-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 63 + description: | + Four-bank activate window in terms of number of clock cycles. + + tMRD-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Mode register set command delay in terms of number of clock cycles. + + tR2R-C2C-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Additional READ-to-READ delay in chip-to-chip cases in terms of number + of clock cycles. + + tRAS-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 63 + description: | + Row active time in terms of number of clock cycles. + + tRC-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 63 + description: | + ACTIVATE-to-ACTIVATE command period in terms of number of clock cycles. + + tRCD-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + RAS-to-CAS delay in terms of number of clock cycles. + + tRFC-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 255 + description: | + Refresh Cycle time in terms of number of clock cycles. + + tRL-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + READ data latency in terms of number of clock cycles. + + tRPab-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Row precharge time (all banks) in terms of number of clock cycles. + + tRPpb-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Row precharge time (single banks) in terms of number of clock cycles. + + tRRD-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Active bank A to active bank B in terms of number of clock cycles. + + tRTP-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Internal READ to PRECHARGE command delay in terms of number of clock + cycles. + + tW2W-C2C-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Additional WRITE-to-WRITE delay in chip-to-chip cases in terms of number + of clock cycles. + + tWL-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + WRITE data latency in terms of number of clock cycles. + + tWR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + WRITE recovery time in terms of number of clock cycles. + + tWTR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 15 + description: | + Internal WRITE-to-READ command delay in terms of number of clock cycles. + + tXP-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 255 + description: | + Exit power-down to next valid command delay in terms of number of clock + cycles. + + tXSR-min-tck: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 1023 + description: | + SELF REFRESH exit to next valid command delay in terms of number of clock + cycles. + +patternProperties: + "^timings((-[0-9])+|(@[0-9a-f]+))?$": + $ref: jedec,lpddr3-timings.yaml + description: | + The lpddr3 node may have one or more child nodes with timings. + Each timing node provides AC timing parameters of the device for a given + speed-bin. The user may provide the timings for as many speed-bins as is + required. + +required: + - compatible + - density + - io-width + +additionalProperties: false + +examples: + - | + lpddr3 { + compatible = "samsung,K3QF2F20DB", "jedec,lpddr3"; + density = <16384>; + io-width = <32>; + + tCKE-min-tck = <2>; + tCKESR-min-tck = <2>; + tDQSCK-min-tck = <5>; + tFAW-min-tck = <5>; + tMRD-min-tck = <5>; + tR2R-C2C-min-tck = <0>; + tRAS-min-tck = <5>; + tRC-min-tck = <6>; + tRCD-min-tck = <3>; + tRFC-min-tck = <17>; + tRL-min-tck = <14>; + tRPab-min-tck = <2>; + tRPpb-min-tck = <2>; + tRRD-min-tck = <2>; + tRTP-min-tck = <2>; + tW2W-C2C-min-tck = <0>; + tWL-min-tck = <8>; + tWR-min-tck = <7>; + tWTR-min-tck = <2>; + tXP-min-tck = <2>; + tXSR-min-tck = <12>; + + timings { + compatible = "jedec,lpddr3-timings"; + max-freq = <800000000>; + min-freq = <100000000>; + tCKE = <3750>; + tCKESR = <3750>; + tFAW = <25000>; + tMRD = <7000>; + tR2R-C2C = <0>; + tRAS = <23000>; + tRC = <33750>; + tRCD = <10000>; + tRFC = <65000>; + tRPab = <12000>; + tRPpb = <12000>; + tRRD = <6000>; + tRTP = <3750>; + tW2W-C2C = <0>; + tWR = <7500>; + tWTR = <3750>; + tXP = <3750>; + tXSR = <70000>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml new file mode 100644 index 000000000..c6e44f47c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/exynos-srom.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC SROM Controller driver + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |+ + The SROM controller can be used to attach external peripherals. In this case + extra properties, describing the bus behind it, should be specified. + +properties: + compatible: + items: + - const: samsung,exynos4210-srom + + reg: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + ranges: + minItems: 1 + maxItems: 4 + description: | + Reflects the memory layout with four integer values per bank. Format: + <bank-number> 0 <parent address of bank> <size> + Up to four banks are supported. + +patternProperties: + "^.*@[0-3],[a-f0-9]+$": + type: object + description: + The actual device nodes should be added as subnodes to the SROMc node. + These subnodes, in addition to regular device specification, should + contain the following properties, describing configuration + of the relevant SROM bank. + + properties: + reg: + description: + Bank number, base address (relative to start of the bank) and size + of the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + maxItems: 1 + + reg-io-width: + enum: [1, 2] + description: + Data width in bytes (1 or 2). If omitted, default of 1 is used. + + samsung,srom-page-mode: + description: + If page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + type: boolean + + samsung,srom-timing: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + minItems: 6 + maxItems: 6 + description: | + Array of 6 integers, specifying bank timings in the following order: + Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following meaning + and valid range: + Tacp: Page mode access cycle at Page mode (0 - 15) + Tcah: Address holding time after CSn (0 - 15) + Tcoh: Chip selection hold on OEn (0 - 15) + Tacc: Access cycle (0 - 31, the actual time is N + 1) + Tcos: Chip selection set-up before OEn (0 - 15) + Tacs: Address set-up before CSn (0 - 15) + + required: + - reg + - samsung,srom-timing + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + // Example: basic definition, no banks are configured + memory-controller@12560000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12560000 0x14>; + }; + + - | + // Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ddr.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ddr.yaml new file mode 100644 index 000000000..84f778a99 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ddr.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ddr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale DDR memory controller + +maintainers: + - Borislav Petkov <bp@alien8.de> + - York Sun <york.sun@nxp.com> + +properties: + $nodename: + pattern: "^memory-controller@[0-9a-f]+$" + + compatible: + oneOf: + - items: + - enum: + - fsl,qoriq-memory-controller-v4.4 + - fsl,qoriq-memory-controller-v4.5 + - fsl,qoriq-memory-controller-v4.7 + - fsl,qoriq-memory-controller-v5.0 + - const: fsl,qoriq-memory-controller + - enum: + - fsl,bsc9132-memory-controller + - fsl,mpc8536-memory-controller + - fsl,mpc8540-memory-controller + - fsl,mpc8541-memory-controller + - fsl,mpc8544-memory-controller + - fsl,mpc8548-memory-controller + - fsl,mpc8555-memory-controller + - fsl,mpc8560-memory-controller + - fsl,mpc8568-memory-controller + - fsl,mpc8569-memory-controller + - fsl,mpc8572-memory-controller + - fsl,mpc8349-memory-controller + - fsl,p1020-memory-controller + - fsl,p1021-memory-controller + - fsl,p2020-memory-controller + - fsl,qoriq-memory-controller + + interrupts: + maxItems: 1 + + little-endian: + description: + Specifies little-endian access to registers. If omitted, big-endian will + be used. + type: boolean + + reg: + maxItems: 1 + +required: + - compatible + - interrupts + - reg + +additionalProperties: false + +examples: + - | + memory-controller@2000 { + compatible = "fsl,bsc9132-memory-controller"; + reg = <0x2000 0x1000>; + interrupts = <16 2 1 8>; + }; + + - | + memory-controller@8000 { + compatible = "fsl,qoriq-memory-controller-v4.7", + "fsl,qoriq-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml new file mode 100644 index 000000000..3be1db30b --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ifc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: FSL/NXP Integrated Flash Controller + +maintainers: + - Li Yang <leoyang.li@nxp.com> + +description: | + NXP's integrated flash controller (IFC) is an advanced version of the + enhanced local bus controller which includes similar programming and signal + interfaces with an extended feature set. The IFC provides access to multiple + external memory types, such as NAND flash (SLC and MLC), NOR flash, EPROM, + SRAM and other memories where address and data are shared on a bus. + +properties: + $nodename: + pattern: "^memory-controller@[0-9a-f]+$" + + compatible: + const: fsl,ifc + + "#address-cells": + enum: [2, 3] + description: | + Should be either two or three. The first cell is the chipselect + number, and the remaining cells are the offset into the chipselect. + + "#size-cells": + enum: [1, 2] + description: | + Either one or two, depending on how large each chipselect can be. + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + description: | + IFC may have one or two interrupts. If two interrupt specifiers are + present, the first is the "common" interrupt (CM_EVTER_STAT), and the + second is the NAND interrupt (NAND_EVTER_STAT). If there is only one, + that interrupt reports both types of event. + + little-endian: + type: boolean + description: | + If this property is absent, the big-endian mode will be in use as default + for registers. + + ranges: + description: | + Each range corresponds to a single chipselect, and covers the entire + access window as configured. + +patternProperties: + "^.*@[a-f0-9]+(,[a-f0-9]+)+$": + type: object + description: | + Child device nodes describe the devices connected to IFC such as NOR (e.g. + cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices + like FPGAs, CPLDs, etc. + + required: + - compatible + - reg + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + soc { + #address-cells = <2>; + #size-cells = <2>; + + memory-controller@ffe1e000 { + compatible = "fsl,ifc"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x0 0xffe1e000 0 0x2000>; + interrupts = <16 2 19 2>; + little-endian; + + /* NOR, NAND Flashes and CPLD on board */ + ranges = <0x0 0x0 0x0 0xee000000 0x02000000>, + <0x1 0x0 0x0 0xffa00000 0x00010000>, + <0x3 0x0 0x0 0xffb00000 0x00020000>; + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x2000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + /* 32MB for user data */ + reg = <0x0 0x02000000>; + label = "NOR Data"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/imx8m-ddrc.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/imx8m-ddrc.yaml new file mode 100644 index 000000000..519b12311 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/imx8m-ddrc.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/fsl/imx8m-ddrc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX8M DDR Controller + +maintainers: + - Peng Fan <peng.fan@nxp.com> + +description: + The DDRC block is integrated in i.MX8M for interfacing with DDR based + memories. + + It supports switching between different frequencies at runtime but during + this process RAM itself becomes briefly inaccessible so actual frequency + switching is implemented by TF-A code which runs from a SRAM area. + + The Linux driver for the DDRC doesn't even map registers (they're included + for the sake of "describing hardware"), it mostly just exposes firmware + capabilities through standard Linux mechanism like devfreq and OPP tables. + +properties: + compatible: + items: + - enum: + - fsl,imx8mn-ddrc + - fsl,imx8mm-ddrc + - fsl,imx8mq-ddrc + - const: fsl,imx8m-ddrc + + reg: + maxItems: 1 + description: + Base address and size of DDRC CTL area. + This is not currently mapped by the imx8m-ddrc driver. + + clocks: + maxItems: 4 + + clock-names: + items: + - const: core + - const: pll + - const: alt + - const: apb + + operating-points-v2: true + opp-table: + type: object + +required: + - reg + - compatible + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mm-clock.h> + ddrc: memory-controller@3d400000 { + compatible = "fsl,imx8mm-ddrc", "fsl,imx8m-ddrc"; + reg = <0x3d400000 0x400000>; + clock-names = "core", "pll", "alt", "apb"; + clocks = <&clk IMX8MM_CLK_DRAM_CORE>, + <&clk IMX8MM_DRAM_PLL>, + <&clk IMX8MM_CLK_DRAM_ALT>, + <&clk IMX8MM_CLK_DRAM_APB>; + operating-points-v2 = <&ddrc_opp_table>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.yaml new file mode 100644 index 000000000..71547eee9 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/fsl/mmdc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Multi Mode DDR controller (MMDC) + +maintainers: + - Anson Huang <Anson.Huang@nxp.com> + +properties: + compatible: + oneOf: + - const: fsl,imx6q-mmdc + - items: + - enum: + - fsl,imx6qp-mmdc + - fsl,imx6sl-mmdc + - fsl,imx6sll-mmdc + - fsl,imx6sx-mmdc + - fsl,imx6ul-mmdc + - fsl,imx7ulp-mmdc + - const: fsl,imx6q-mmdc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + + memory-controller@21b0000 { + compatible = "fsl,imx6q-mmdc"; + reg = <0x021b0000 0x4000>; + clocks = <&clks IMX6QDL_CLK_MMDC_P0_IPG>; + }; + + memory-controller@21b4000 { + compatible = "fsl,imx6q-mmdc"; + reg = <0x021b4000 0x4000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc-peripherals.yaml b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc-peripherals.yaml new file mode 100644 index 000000000..b8ed52a44 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc-peripherals.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ingenic,nemc-peripherals.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs NAND / External Memory Controller (NEMC) devicetree bindings + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + reg: + minItems: 1 + maxItems: 255 + + ingenic,nemc-bus-width: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [8, 16] + description: Specifies the bus width in bits. + + ingenic,nemc-tAS: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Address setup time in nanoseconds. + + ingenic,nemc-tAH: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Address hold time in nanoseconds. + + ingenic,nemc-tBP: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Burst pitch time in nanoseconds. + + ingenic,nemc-tAW: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Address wait time in nanoseconds. + + ingenic,nemc-tSTRV: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Static memory recovery time in nanoseconds. + +required: + - reg + +additionalProperties: true +... diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml new file mode 100644 index 000000000..dd13a5106 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ingenic,nemc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs NAND / External Memory Controller (NEMC) devicetree bindings + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + $nodename: + pattern: "^memory-controller@[0-9a-f]+$" + + compatible: + oneOf: + - enum: + - ingenic,jz4740-nemc + - ingenic,jz4780-nemc + - items: + - const: ingenic,jz4725b-nemc + - const: ingenic,jz4740-nemc + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + ranges: true + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + +patternProperties: + ".*@[0-9]+$": + type: object + +required: + - compatible + - "#address-cells" + - "#size-cells" + - ranges + - reg + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/ingenic,jz4780-cgu.h> + #include <dt-bindings/gpio/gpio.h> + nemc: memory-controller@13410000 { + compatible = "ingenic,jz4780-nemc"; + reg = <0x13410000 0x10000>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <1 0 0x1b000000 0x1000000>, + <2 0 0x1a000000 0x1000000>, + <3 0 0x19000000 0x1000000>, + <4 0 0x18000000 0x1000000>, + <5 0 0x17000000 0x1000000>, + <6 0 0x16000000 0x1000000>; + + clocks = <&cgu JZ4780_CLK_NEMC>; + + ethernet@6 { + compatible = "davicom,dm9000"; + davicom,no-eeprom; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_nemc_cs6>; + + reg = <6 0 1>, /* addr */ + <6 2 1>; /* data */ + + ingenic,nemc-tAS = <15>; + ingenic,nemc-tAH = <10>; + ingenic,nemc-tBP = <20>; + ingenic,nemc-tAW = <50>; + ingenic,nemc-tSTRV = <100>; + + reset-gpios = <&gpf 12 GPIO_ACTIVE_HIGH>; + vcc-supply = <ð0_power>; + + interrupt-parent = <&gpe>; + interrupts = <19 4>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/marvell,mvebu-sdram-controller.yaml b/Documentation/devicetree/bindings/memory-controllers/marvell,mvebu-sdram-controller.yaml new file mode 100644 index 000000000..9249624c4 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/marvell,mvebu-sdram-controller.yaml @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/marvell,mvebu-sdram-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MVEBU SDRAM controller + +maintainers: + - Jan Luebbe <jlu@pengutronix.de> + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: marvell,armada-xp-sdram-controller + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + memory-controller@1400 { + compatible = "marvell,armada-xp-sdram-controller"; + reg = <0x1400 0x500>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,mt7621-memc.yaml b/Documentation/devicetree/bindings/memory-controllers/mediatek,mt7621-memc.yaml new file mode 100644 index 000000000..6ccdaf99c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,mt7621-memc.yaml @@ -0,0 +1,32 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/mediatek,mt7621-memc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MT7621 SDRAM controller + +maintainers: + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +properties: + compatible: + items: + - const: mediatek,mt7621-memc + - const: syscon + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + memory-controller@5000 { + compatible = "mediatek,mt7621-memc", "syscon"; + reg = <0x5000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml new file mode 100644 index 000000000..a8fda30cc --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml @@ -0,0 +1,182 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/mediatek,smi-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SMI (Smart Multimedia Interface) Common + +maintainers: + - Yong Wu <yong.wu@mediatek.com> + +description: | + The hardware block diagram please check bindings/iommu/mediatek,iommu.yaml + + MediaTek SMI have two generations of HW architecture, here is the list + which generation the SoCs use: + generation 1: mt2701 and mt7623. + generation 2: mt2712, mt6779, mt8167, mt8173, mt8183, mt8186, mt8188, mt8192 and mt8195. + + There's slight differences between the two SMI, for generation 2, the + register which control the iommu port is at each larb's register base. But + for generation 1, the register is at smi ao base(smi always on register + base). Besides that, the smi async clock should be prepared and enabled for + SMI generation 1 to transform the smi clock into emi clock domain, but that is + not needed for SMI generation 2. + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt2701-smi-common + - mediatek,mt2712-smi-common + - mediatek,mt6779-smi-common + - mediatek,mt6795-smi-common + - mediatek,mt8167-smi-common + - mediatek,mt8173-smi-common + - mediatek,mt8183-smi-common + - mediatek,mt8186-smi-common + - mediatek,mt8188-smi-common-vdo + - mediatek,mt8188-smi-common-vpp + - mediatek,mt8192-smi-common + - mediatek,mt8195-smi-common-vdo + - mediatek,mt8195-smi-common-vpp + - mediatek,mt8195-smi-sub-common + + - description: for mt7623 + items: + - const: mediatek,mt7623-smi-common + - const: mediatek,mt2701-smi-common + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + clocks: + description: | + apb and smi are mandatory. the async is only for generation 1 smi HW. + gals(global async local sync) also is optional, see below. + minItems: 2 + items: + - description: apb is Advanced Peripheral Bus clock, It's the clock for + setting the register. + - description: smi is the clock for transfer data and command. + - description: Either asynchronous clock to help transform the smi clock + into the emi clock domain on Gen1 h/w, or the path0 clock of gals. + - description: gals1 is the path1 clock of gals. + + clock-names: + minItems: 2 + maxItems: 4 + + mediatek,smi: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the smi-common node above. Only for sub-common. + +required: + - compatible + - reg + - power-domains + - clocks + - clock-names + +allOf: + - if: # only for gen1 HW + properties: + compatible: + contains: + enum: + - mediatek,mt2701-smi-common + then: + properties: + clocks: + minItems: 3 + maxItems: 3 + clock-names: + items: + - const: apb + - const: smi + - const: async + + - if: # only for sub common + properties: + compatible: + contains: + enum: + - mediatek,mt8195-smi-sub-common + then: + required: + - mediatek,smi + properties: + clocks: + minItems: 3 + maxItems: 3 + clock-names: + items: + - const: apb + - const: smi + - const: gals0 + else: + properties: + mediatek,smi: false + + - if: # for gen2 HW that have gals + properties: + compatible: + enum: + - mediatek,mt6779-smi-common + - mediatek,mt8183-smi-common + - mediatek,mt8186-smi-common + - mediatek,mt8192-smi-common + - mediatek,mt8195-smi-common-vdo + - mediatek,mt8195-smi-common-vpp + + then: + properties: + clocks: + minItems: 4 + maxItems: 4 + clock-names: + items: + - const: apb + - const: smi + - const: gals0 + - const: gals1 + + - if: # for gen2 HW that don't have gals + properties: + compatible: + enum: + - mediatek,mt2712-smi-common + - mediatek,mt6795-smi-common + - mediatek,mt8167-smi-common + - mediatek,mt8173-smi-common + + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: apb + - const: smi + +additionalProperties: false + +examples: + - |+ + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/power/mt8173-power.h> + + smi_common: smi@14022000 { + compatible = "mediatek,mt8173-smi-common"; + reg = <0x14022000 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_SMI_COMMON>, + <&mmsys CLK_MM_SMI_COMMON>; + clock-names = "apb", "smi"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml new file mode 100644 index 000000000..5f4ac3609 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/mediatek,smi-larb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SMI (Smart Multimedia Interface) Local Arbiter + +maintainers: + - Yong Wu <yong.wu@mediatek.com> + +description: | + The hardware block diagram please check bindings/iommu/mediatek,iommu.yaml + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt2701-smi-larb + - mediatek,mt2712-smi-larb + - mediatek,mt6779-smi-larb + - mediatek,mt6795-smi-larb + - mediatek,mt8167-smi-larb + - mediatek,mt8173-smi-larb + - mediatek,mt8183-smi-larb + - mediatek,mt8186-smi-larb + - mediatek,mt8188-smi-larb + - mediatek,mt8192-smi-larb + - mediatek,mt8195-smi-larb + + - description: for mt7623 + items: + - const: mediatek,mt7623-smi-larb + - const: mediatek,mt2701-smi-larb + + reg: + maxItems: 1 + + clocks: + description: | + apb and smi are mandatory. gals(global async local sync) is optional. + minItems: 2 + items: + - description: apb is Advanced Peripheral Bus clock, It's the clock for + setting the register. + - description: smi is the clock for transfer data and command. + - description: the clock for gals. + + clock-names: + minItems: 2 + maxItems: 3 + + power-domains: + maxItems: 1 + + mediatek,smi: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the smi_common node. + + mediatek,larb-id: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: the hardware id of this larb. It's only required when this + hardward id is not consecutive from its M4U point of view. + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + +allOf: + - if: # HW has gals + properties: + compatible: + enum: + - mediatek,mt8183-smi-larb + - mediatek,mt8186-smi-larb + - mediatek,mt8188-smi-larb + - mediatek,mt8195-smi-larb + + then: + properties: + clocks: + minItems: 2 + maxItems: 3 + clock-names: + minItems: 2 + items: + - const: apb + - const: smi + - const: gals + + else: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: apb + - const: smi + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt2701-smi-larb + - mediatek,mt2712-smi-larb + - mediatek,mt6779-smi-larb + - mediatek,mt8186-smi-larb + - mediatek,mt8188-smi-larb + - mediatek,mt8192-smi-larb + - mediatek,mt8195-smi-larb + + then: + required: + - mediatek,larb-id + +additionalProperties: false + +examples: + - |+ + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/power/mt8173-power.h> + + larb1: larb@16010000 { + compatible = "mediatek,mt8173-smi-larb"; + reg = <0x16010000 0x1000>; + mediatek,smi = <&smi_common>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&vdecsys CLK_VDEC_CKEN>, + <&vdecsys CLK_VDEC_LARB_CKEN>; + clock-names = "apb", "smi"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt new file mode 100644 index 000000000..8b9388cc1 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt @@ -0,0 +1,177 @@ +Device tree bindings for MVEBU Device Bus controllers + +The Device Bus controller available in some Marvell's SoC allows to control +different types of standard memory and I/O devices such as NOR, NAND, and FPGA. +The actual devices are instantiated from the child nodes of a Device Bus node. + +Required properties: + + - compatible: Armada 370/XP SoC are supported using the + "marvell,mvebu-devbus" compatible string. + + Orion5x SoC are supported using the + "marvell,orion-devbus" compatible string. + + - reg: A resource specifier for the register space. + This is the base address of a chip select within + the controller's register space. + (see the example below) + + - #address-cells: Must be set to 1 + - #size-cells: Must be set to 1 + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + 0 <physical address of mapping> <size> + +Optional properties: + + - devbus,keep-config This property can optionally be used to keep + using the timing parameters set by the + bootloader. It makes all the timing properties + described below unused. + +Timing properties for child nodes: + +Read parameters: + + - devbus,turn-off-ps: Defines the time during which the controller does not + drive the AD bus after the completion of a device read. + This prevents contentions on the Device Bus after a read + cycle from a slow device. + Mandatory, except if devbus,keep-config is used. + + - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). + Mandatory, except if devbus,keep-config is used. + + - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, + to read data sample. This parameter is useful for + synchronous pipelined devices, where the address + precedes the read data by one or two cycles. + Mandatory, except if devbus,keep-config is used. + + - devbus,acc-first-ps: Defines the time delay from the negation of + ALE[0] to the cycle that the first read data is sampled + by the controller. + Mandatory, except if devbus,keep-config is used. + + - devbus,acc-next-ps: Defines the time delay between the cycle that + samples data N and the cycle that samples data N+1 + (in burst accesses). + Mandatory, except if devbus,keep-config is used. + + - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to + DEV_OEn assertion. If set to 0 (default), + DEV_OEn and DEV_CSn are asserted at the same cycle. + This parameter has no affect on <acc-first-ps> parameter + (no affect on first data sample). Set <rd-setup-ps> + to a value smaller than <acc-first-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. + + - devbus,rd-hold-ps: Defines the time between the last data sample to the + de-assertion of DEV_CSn. If set to 0 (default), + DEV_OEn and DEV_CSn are de-asserted at the same cycle + (the cycle of the last data sample). + This parameter has no affect on DEV_OEn de-assertion. + DEV_OEn is always de-asserted the next cycle after + last data sampled. Also this parameter has no + affect on <turn-off-ps> parameter. + Set <rd-hold-ps> to a value smaller than <turn-off-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. + +Write parameters: + + - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle + to the DEV_WEn assertion. + Mandatory. + + - devbus,wr-low-ps: Defines the time during which DEV_WEn is active. + A[2:0] and Data are kept valid as long as DEV_WEn + is active. This parameter defines the setup time of + address and data to DEV_WEn rise. + Mandatory. + + - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept + inactive (high) between data beats of a burst write. + DEV_A[2:0] and Data are kept valid (do not toggle) for + <wr-high-ps> - <tick> ps. + This parameter defines the hold time of address and + data after DEV_WEn rise. + Mandatory. + + - devbus,sync-enable: Synchronous device enable. + 1: True + 0: False + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. + +An example for an Armada XP GP board, with a 16 MiB NOR device as child +is showed below. Note that the Device Bus driver is in charge of allocating +the mbus address decoding window for each of its child devices. +The window is created using the chip select specified in the child +device node together with the base address and size specified in the ranges +property. For instance, in the example below the allocated decoding window +will start at base address 0xf0000000, with a size 0x1000000 (16 MiB) +for chip select 0 (a.k.a DEV_BOOTCS). + +This address window handling is done in this mvebu-devbus only as a temporary +solution. It will be removed when the support for mbus device tree binding is +added. + +The reg property implicitly specifies the chip select as this: + + 0x10400: DEV_BOOTCS + 0x10408: DEV_CS0 + 0x10410: DEV_CS1 + 0x10418: DEV_CS2 + 0x10420: DEV_CS3 + +Example: + + devbus-bootcs@d0010400 { + ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */ + #address-cells = <1>; + #size-cells = <1>; + + /* Device Bus parameters are required */ + + /* Read parameters */ + devbus,bus-width = <8>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; + + flash@0 { + compatible = "cfi-flash"; + + /* 16 MiB */ + reg = <0 0x1000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + + /* + * We split the 16 MiB in two partitions, + * just as an example. + */ + partition@0 { + label = "First"; + reg = <0 0x800000>; + }; + + partition@800000 { + label = "Second"; + reg = <0x800000 0x800000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.yaml new file mode 100644 index 000000000..9163c3f12 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.yaml @@ -0,0 +1,549 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra124-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra124 SoC External Memory Controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The EMC interfaces with the off-chip SDRAM to service the request stream + sent from the memory controller. + +properties: + compatible: + const: nvidia,tegra124-emc + + reg: + maxItems: 1 + + clocks: + items: + - description: external memory clock + + clock-names: + items: + - const: emc + + "#interconnect-cells": + const: 0 + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle of the memory controller node + + power-domains: + maxItems: 1 + description: + Phandle of the SoC "core" power domain. + + operating-points-v2: + description: + Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC speedo ID mask. + +patternProperties: + "^emc-timings-[0-9]+$": + type: object + properties: + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the RAM_CODE field in the PMC_STRAPPING_OPT_A register that + this timing set is used for + + patternProperties: + "^timing-[0-9]+$": + type: object + properties: + clock-frequency: + description: + external memory clock rate in Hz + minimum: 1000000 + maximum: 1000000000 + + nvidia,emc-auto-cal-config: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_AUTO_CAL_CONFIG register for this set of + timings + + nvidia,emc-auto-cal-config2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_AUTO_CAL_CONFIG2 register for this set of + timings + + nvidia,emc-auto-cal-config3: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_AUTO_CAL_CONFIG3 register for this set of + timings + + nvidia,emc-auto-cal-interval: + description: + pad calibration interval in microseconds + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 2097151 + + nvidia,emc-bgbias-ctl0: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_BGBIAS_CTL0 register for this set of timings + + nvidia,emc-cfg: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_CFG register for this set of timings + + nvidia,emc-cfg-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_CFG_2 register for this set of timings + + nvidia,emc-ctt-term-ctrl: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_CTT_TERM_CTRL register for this set of timings + + nvidia,emc-mode-1: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_MRW register for this set of timings + + nvidia,emc-mode-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_MRW2 register for this set of timings + + nvidia,emc-mode-4: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_MRW4 register for this set of timings + + nvidia,emc-mode-reset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + reset value of the EMC_MRS register for this set of timings + + nvidia,emc-mrs-wait-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMR_MRS_WAIT_CNT register for this set of timings + + nvidia,emc-sel-dpd-ctrl: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_SEL_DPD_CTRL register for this set of timings + + nvidia,emc-xm2dqspadctrl2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_XM2DQSPADCTRL2 register for this set of timings + + nvidia,emc-zcal-cnt-long: + description: + number of EMC clocks to wait before issuing any commands after + clock change + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1023 + + nvidia,emc-zcal-interval: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + value of the EMC_ZCAL_INTERVAL register for this set of timings + + nvidia,emc-configuration: + description: + EMC timing characterization data. These are the registers (see + section "15.6.2 EMC Registers" in the TRM) whose values need to + be specified, according to the board documentation. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: EMC_RC + - description: EMC_RFC + - description: EMC_RFC_SLR + - description: EMC_RAS + - description: EMC_RP + - description: EMC_R2W + - description: EMC_W2R + - description: EMC_R2P + - description: EMC_W2P + - description: EMC_RD_RCD + - description: EMC_WR_RCD + - description: EMC_RRD + - description: EMC_REXT + - description: EMC_WEXT + - description: EMC_WDV + - description: EMC_WDV_MASK + - description: EMC_QUSE + - description: EMC_QUSE_WIDTH + - description: EMC_IBDLY + - description: EMC_EINPUT + - description: EMC_EINPUT_DURATION + - description: EMC_PUTERM_EXTRA + - description: EMC_PUTERM_WIDTH + - description: EMC_PUTERM_ADJ + - description: EMC_CDB_CNTL_1 + - description: EMC_CDB_CNTL_2 + - description: EMC_CDB_CNTL_3 + - description: EMC_QRST + - description: EMC_QSAFE + - description: EMC_RDV + - description: EMC_RDV_MASK + - description: EMC_REFRESH + - description: EMC_BURST_REFRESH_NUM + - description: EMC_PRE_REFRESH_REQ_CNT + - description: EMC_PDEX2WR + - description: EMC_PDEX2RD + - description: EMC_PCHG2PDEN + - description: EMC_ACT2PDEN + - description: EMC_AR2PDEN + - description: EMC_RW2PDEN + - description: EMC_TXSR + - description: EMC_TXSRDLL + - description: EMC_TCKE + - description: EMC_TCKESR + - description: EMC_TPD + - description: EMC_TFAW + - description: EMC_TRPAB + - description: EMC_TCLKSTABLE + - description: EMC_TCLKSTOP + - description: EMC_TREFBW + - description: EMC_FBIO_CFG6 + - description: EMC_ODT_WRITE + - description: EMC_ODT_READ + - description: EMC_FBIO_CFG5 + - description: EMC_CFG_DIG_DLL + - description: EMC_CFG_DIG_DLL_PERIOD + - description: EMC_DLL_XFORM_DQS0 + - description: EMC_DLL_XFORM_DQS1 + - description: EMC_DLL_XFORM_DQS2 + - description: EMC_DLL_XFORM_DQS3 + - description: EMC_DLL_XFORM_DQS4 + - description: EMC_DLL_XFORM_DQS5 + - description: EMC_DLL_XFORM_DQS6 + - description: EMC_DLL_XFORM_DQS7 + - description: EMC_DLL_XFORM_DQS8 + - description: EMC_DLL_XFORM_DQS9 + - description: EMC_DLL_XFORM_DQS10 + - description: EMC_DLL_XFORM_DQS11 + - description: EMC_DLL_XFORM_DQS12 + - description: EMC_DLL_XFORM_DQS13 + - description: EMC_DLL_XFORM_DQS14 + - description: EMC_DLL_XFORM_DQS15 + - description: EMC_DLL_XFORM_QUSE0 + - description: EMC_DLL_XFORM_QUSE1 + - description: EMC_DLL_XFORM_QUSE2 + - description: EMC_DLL_XFORM_QUSE3 + - description: EMC_DLL_XFORM_QUSE4 + - description: EMC_DLL_XFORM_QUSE5 + - description: EMC_DLL_XFORM_QUSE6 + - description: EMC_DLL_XFORM_QUSE7 + - description: EMC_DLL_XFORM_ADDR0 + - description: EMC_DLL_XFORM_ADDR1 + - description: EMC_DLL_XFORM_ADDR2 + - description: EMC_DLL_XFORM_ADDR3 + - description: EMC_DLL_XFORM_ADDR4 + - description: EMC_DLL_XFORM_ADDR5 + - description: EMC_DLL_XFORM_QUSE8 + - description: EMC_DLL_XFORM_QUSE9 + - description: EMC_DLL_XFORM_QUSE10 + - description: EMC_DLL_XFORM_QUSE11 + - description: EMC_DLL_XFORM_QUSE12 + - description: EMC_DLL_XFORM_QUSE13 + - description: EMC_DLL_XFORM_QUSE14 + - description: EMC_DLL_XFORM_QUSE15 + - description: EMC_DLI_TRIM_TXDQS0 + - description: EMC_DLI_TRIM_TXDQS1 + - description: EMC_DLI_TRIM_TXDQS2 + - description: EMC_DLI_TRIM_TXDQS3 + - description: EMC_DLI_TRIM_TXDQS4 + - description: EMC_DLI_TRIM_TXDQS5 + - description: EMC_DLI_TRIM_TXDQS6 + - description: EMC_DLI_TRIM_TXDQS7 + - description: EMC_DLI_TRIM_TXDQS8 + - description: EMC_DLI_TRIM_TXDQS9 + - description: EMC_DLI_TRIM_TXDQS10 + - description: EMC_DLI_TRIM_TXDQS11 + - description: EMC_DLI_TRIM_TXDQS12 + - description: EMC_DLI_TRIM_TXDQS13 + - description: EMC_DLI_TRIM_TXDQS14 + - description: EMC_DLI_TRIM_TXDQS15 + - description: EMC_DLL_XFORM_DQ0 + - description: EMC_DLL_XFORM_DQ1 + - description: EMC_DLL_XFORM_DQ2 + - description: EMC_DLL_XFORM_DQ3 + - description: EMC_DLL_XFORM_DQ4 + - description: EMC_DLL_XFORM_DQ5 + - description: EMC_DLL_XFORM_DQ6 + - description: EMC_DLL_XFORM_DQ7 + - description: EMC_XM2CMDPADCTRL + - description: EMC_XM2CMDPADCTRL4 + - description: EMC_XM2CMDPADCTRL5 + - description: EMC_XM2DQPADCTRL2 + - description: EMC_XM2DQPADCTRL3 + - description: EMC_XM2CLKPADCTRL + - description: EMC_XM2CLKPADCTRL2 + - description: EMC_XM2COMPPADCTRL + - description: EMC_XM2VTTGENPADCTRL + - description: EMC_XM2VTTGENPADCTRL2 + - description: EMC_XM2VTTGENPADCTRL3 + - description: EMC_XM2DQSPADCTRL3 + - description: EMC_XM2DQSPADCTRL4 + - description: EMC_XM2DQSPADCTRL5 + - description: EMC_XM2DQSPADCTRL6 + - description: EMC_DSR_VTTGEN_DRV + - description: EMC_TXDSRVTTGEN + - description: EMC_FBIO_SPARE + - description: EMC_ZCAL_WAIT_CNT + - description: EMC_MRS_WAIT_CNT2 + - description: EMC_CTT + - description: EMC_CTT_DURATION + - description: EMC_CFG_PIPE + - description: EMC_DYN_SELF_REF_CONTROL + - description: EMC_QPOP + + required: + - clock-frequency + - nvidia,emc-auto-cal-config + - nvidia,emc-auto-cal-config2 + - nvidia,emc-auto-cal-config3 + - nvidia,emc-auto-cal-interval + - nvidia,emc-bgbias-ctl0 + - nvidia,emc-cfg + - nvidia,emc-cfg-2 + - nvidia,emc-ctt-term-ctrl + - nvidia,emc-mode-1 + - nvidia,emc-mode-2 + - nvidia,emc-mode-4 + - nvidia,emc-mode-reset + - nvidia,emc-mrs-wait-cnt + - nvidia,emc-sel-dpd-ctrl + - nvidia,emc-xm2dqspadctrl2 + - nvidia,emc-zcal-cnt-long + - nvidia,emc-zcal-interval + - nvidia,emc-configuration + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - nvidia,memory-controller + - "#interconnect-cells" + - operating-points-v2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/tegra124-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mc: memory-controller@70019000 { + compatible = "nvidia,tegra124-mc"; + reg = <0x70019000 0x1000>; + clocks = <&tegra_car TEGRA124_CLK_MC>; + clock-names = "mc"; + + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + + #iommu-cells = <1>; + #reset-cells = <1>; + #interconnect-cells = <1>; + }; + + external-memory-controller@7001b000 { + compatible = "nvidia,tegra124-emc"; + reg = <0x7001b000 0x1000>; + clocks = <&car TEGRA124_CLK_EMC>; + clock-names = "emc"; + + nvidia,memory-controller = <&mc>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + + #interconnect-cells = <0>; + + emc-timings-0 { + nvidia,ram-code = <3>; + + timing-0 { + clock-frequency = <12750000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 /* EMC_RC */ + 0x00000003 /* EMC_RFC */ + 0x00000000 /* EMC_RFC_SLR */ + 0x00000000 /* EMC_RAS */ + 0x00000000 /* EMC_RP */ + 0x00000004 /* EMC_R2W */ + 0x0000000a /* EMC_W2R */ + 0x00000003 /* EMC_R2P */ + 0x0000000b /* EMC_W2P */ + 0x00000000 /* EMC_RD_RCD */ + 0x00000000 /* EMC_WR_RCD */ + 0x00000003 /* EMC_RRD */ + 0x00000003 /* EMC_REXT */ + 0x00000000 /* EMC_WEXT */ + 0x00000006 /* EMC_WDV */ + 0x00000006 /* EMC_WDV_MASK */ + 0x00000006 /* EMC_QUSE */ + 0x00000002 /* EMC_QUSE_WIDTH */ + 0x00000000 /* EMC_IBDLY */ + 0x00000005 /* EMC_EINPUT */ + 0x00000005 /* EMC_EINPUT_DURATION */ + 0x00010000 /* EMC_PUTERM_EXTRA */ + 0x00000003 /* EMC_PUTERM_WIDTH */ + 0x00000000 /* EMC_PUTERM_ADJ */ + 0x00000000 /* EMC_CDB_CNTL_1 */ + 0x00000000 /* EMC_CDB_CNTL_2 */ + 0x00000000 /* EMC_CDB_CNTL_3 */ + 0x00000004 /* EMC_QRST */ + 0x0000000c /* EMC_QSAFE */ + 0x0000000d /* EMC_RDV */ + 0x0000000f /* EMC_RDV_MASK */ + 0x00000060 /* EMC_REFRESH */ + 0x00000000 /* EMC_BURST_REFRESH_NUM */ + 0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */ + 0x00000002 /* EMC_PDEX2WR */ + 0x00000002 /* EMC_PDEX2RD */ + 0x00000001 /* EMC_PCHG2PDEN */ + 0x00000000 /* EMC_ACT2PDEN */ + 0x00000007 /* EMC_AR2PDEN */ + 0x0000000f /* EMC_RW2PDEN */ + 0x00000005 /* EMC_TXSR */ + 0x00000005 /* EMC_TXSRDLL */ + 0x00000004 /* EMC_TCKE */ + 0x00000005 /* EMC_TCKESR */ + 0x00000004 /* EMC_TPD */ + 0x00000000 /* EMC_TFAW */ + 0x00000000 /* EMC_TRPAB */ + 0x00000005 /* EMC_TCLKSTABLE */ + 0x00000005 /* EMC_TCLKSTOP */ + 0x00000064 /* EMC_TREFBW */ + 0x00000000 /* EMC_FBIO_CFG6 */ + 0x00000000 /* EMC_ODT_WRITE */ + 0x00000000 /* EMC_ODT_READ */ + 0x106aa298 /* EMC_FBIO_CFG5 */ + 0x002c00a0 /* EMC_CFG_DIG_DLL */ + 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ + 0x00064000 /* EMC_DLL_XFORM_DQS0 */ + 0x00064000 /* EMC_DLL_XFORM_DQS1 */ + 0x00064000 /* EMC_DLL_XFORM_DQS2 */ + 0x00064000 /* EMC_DLL_XFORM_DQS3 */ + 0x00064000 /* EMC_DLL_XFORM_DQS4 */ + 0x00064000 /* EMC_DLL_XFORM_DQS5 */ + 0x00064000 /* EMC_DLL_XFORM_DQS6 */ + 0x00064000 /* EMC_DLL_XFORM_DQS7 */ + 0x00064000 /* EMC_DLL_XFORM_DQS8 */ + 0x00064000 /* EMC_DLL_XFORM_DQS9 */ + 0x00064000 /* EMC_DLL_XFORM_DQS10 */ + 0x00064000 /* EMC_DLL_XFORM_DQS11 */ + 0x00064000 /* EMC_DLL_XFORM_DQS12 */ + 0x00064000 /* EMC_DLL_XFORM_DQS13 */ + 0x00064000 /* EMC_DLL_XFORM_DQS14 */ + 0x00064000 /* EMC_DLL_XFORM_DQS15 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE0 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE1 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE2 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE3 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR0 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR1 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR2 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR3 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR4 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE8 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE9 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE10 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE11 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE12 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE13 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE14 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE15 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS8 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS9 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS10 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS11 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS12 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS13 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS14 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS15 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ0 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ1 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ2 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ3 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ4 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ5 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ6 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ7 */ + 0x10000280 /* EMC_XM2CMDPADCTRL */ + 0x00000000 /* EMC_XM2CMDPADCTRL4 */ + 0x00111111 /* EMC_XM2CMDPADCTRL5 */ + 0x00000000 /* EMC_XM2DQPADCTRL2 */ + 0x00000000 /* EMC_XM2DQPADCTRL3 */ + 0x77ffc081 /* EMC_XM2CLKPADCTRL */ + 0x00000e0e /* EMC_XM2CLKPADCTRL2 */ + 0x81f1f108 /* EMC_XM2COMPPADCTRL */ + 0x07070004 /* EMC_XM2VTTGENPADCTRL */ + 0x0000003f /* EMC_XM2VTTGENPADCTRL2 */ + 0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */ + 0x51451400 /* EMC_XM2DQSPADCTRL3 */ + 0x00514514 /* EMC_XM2DQSPADCTRL4 */ + 0x00514514 /* EMC_XM2DQSPADCTRL5 */ + 0x51451400 /* EMC_XM2DQSPADCTRL6 */ + 0x0000003f /* EMC_DSR_VTTGEN_DRV */ + 0x00000007 /* EMC_TXDSRVTTGEN */ + 0x00000000 /* EMC_FBIO_SPARE */ + 0x00000042 /* EMC_ZCAL_WAIT_CNT */ + 0x000e000e /* EMC_MRS_WAIT_CNT2 */ + 0x00000000 /* EMC_CTT */ + 0x00000003 /* EMC_CTT_DURATION */ + 0x0000f2f3 /* EMC_CFG_PIPE */ + 0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */ + 0x0000000a /* EMC_QPOP */ + >; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-mc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-mc.yaml new file mode 100644 index 000000000..7b18b4d11 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-mc.yaml @@ -0,0 +1,157 @@ +# SPDX-License-Identifier: (GPL-2.0) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra124-mc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra124 SoC Memory Controller + +maintainers: + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + Tegra124 SoC features a hybrid 2x32-bit / 1x64-bit memory controller. + These are interleaved to provide high performance with the load shared across + two memory channels. The Tegra124 Memory Controller handles memory requests + from internal clients and arbitrates among them to allocate memory bandwidth + for DDR3L and LPDDR3 SDRAMs. + +properties: + compatible: + const: nvidia,tegra124-mc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mc + + interrupts: + maxItems: 1 + + "#reset-cells": + const: 1 + + "#iommu-cells": + const: 1 + + "#interconnect-cells": + const: 1 + +patternProperties: + "^emc-timings-[0-9]+$": + type: object + properties: + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value of RAM_CODE this timing set is used for. + + patternProperties: + "^timing-[0-9]+$": + type: object + properties: + clock-frequency: + description: + Memory clock rate in Hz. + minimum: 1000000 + maximum: 1066000000 + + nvidia,emem-configuration: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Values to be written to the EMEM register block. See section + "15.6.1 MC Registers" in the TRM. + items: + - description: MC_EMEM_ARB_CFG + - description: MC_EMEM_ARB_OUTSTANDING_REQ + - description: MC_EMEM_ARB_TIMING_RCD + - description: MC_EMEM_ARB_TIMING_RP + - description: MC_EMEM_ARB_TIMING_RC + - description: MC_EMEM_ARB_TIMING_RAS + - description: MC_EMEM_ARB_TIMING_FAW + - description: MC_EMEM_ARB_TIMING_RRD + - description: MC_EMEM_ARB_TIMING_RAP2PRE + - description: MC_EMEM_ARB_TIMING_WAP2PRE + - description: MC_EMEM_ARB_TIMING_R2R + - description: MC_EMEM_ARB_TIMING_W2W + - description: MC_EMEM_ARB_TIMING_R2W + - description: MC_EMEM_ARB_TIMING_W2R + - description: MC_EMEM_ARB_DA_TURNS + - description: MC_EMEM_ARB_DA_COVERS + - description: MC_EMEM_ARB_MISC0 + - description: MC_EMEM_ARB_MISC1 + - description: MC_EMEM_ARB_RING1_THROTTLE + + required: + - clock-frequency + - nvidia,emem-configuration + + additionalProperties: false + + required: + - nvidia,ram-code + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - "#reset-cells" + - "#iommu-cells" + - "#interconnect-cells" + +additionalProperties: false + +examples: + - | + memory-controller@70019000 { + compatible = "nvidia,tegra124-mc"; + reg = <0x70019000 0x1000>; + clocks = <&tegra_car 32>; + clock-names = "mc"; + + interrupts = <0 77 4>; + + #iommu-cells = <1>; + #reset-cells = <1>; + #interconnect-cells = <1>; + + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 /* MC_EMEM_ARB_CFG */ + 0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RCD */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RP */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RC */ + 0x00000000 /* MC_EMEM_ARB_TIMING_RAS */ + 0x00000002 /* MC_EMEM_ARB_TIMING_FAW */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */ + 0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2R */ + 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2W */ + 0x00000006 /* MC_EMEM_ARB_TIMING_W2R */ + 0x06030203 /* MC_EMEM_ARB_DA_TURNS */ + 0x000a0402 /* MC_EMEM_ARB_DA_COVERS */ + 0x77e30303 /* MC_EMEM_ARB_MISC0 */ + 0x70000f03 /* MC_EMEM_ARB_MISC1 */ + 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ + >; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra186-mc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra186-mc.yaml new file mode 100644 index 000000000..935d63d18 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra186-mc.yaml @@ -0,0 +1,276 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra186-mc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra186 (and later) SoC Memory Controller + +maintainers: + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + The NVIDIA Tegra186 SoC features a 128 bit memory controller that is split + into four 32 bit channels to support LPDDR4 with x16 subpartitions. The MC + handles memory requests for 40-bit virtual addresses from internal clients + and arbitrates among them to allocate memory bandwidth. + + Up to 15 GiB of physical memory can be supported. Security features such as + encryption of traffic to and from DRAM via general security apertures are + available for video and other secure applications, as well as DRAM ECC for + automotive safety applications (single bit error correction and double bit + error detection). + +properties: + $nodename: + pattern: "^memory-controller@[0-9a-f]+$" + + compatible: + items: + - enum: + - nvidia,tegra186-mc + - nvidia,tegra194-mc + - nvidia,tegra234-mc + + reg: + minItems: 6 + maxItems: 18 + + reg-names: + minItems: 6 + maxItems: 18 + + interrupts: + items: + - description: MC general interrupt + + "#address-cells": + const: 2 + + "#size-cells": + const: 2 + + ranges: true + + dma-ranges: true + + "#interconnect-cells": + const: 1 + +patternProperties: + "^external-memory-controller@[0-9a-f]+$": + description: + The bulk of the work involved in controlling the external memory + controller on NVIDIA Tegra186 and later is performed on the BPMP. This + coprocessor exposes the EMC clock that is used to set the frequency at + which the external memory is clocked and a remote procedure call that + can be used to obtain the set of available frequencies. + type: object + properties: + compatible: + items: + - enum: + - nvidia,tegra186-emc + - nvidia,tegra194-emc + - nvidia,tegra234-emc + + reg: + minItems: 1 + maxItems: 2 + + interrupts: + items: + - description: EMC general interrupt + + clocks: + items: + - description: external memory clock + + clock-names: + items: + - const: emc + + "#interconnect-cells": + const: 0 + + nvidia,bpmp: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle of the node representing the BPMP + + allOf: + - if: + properties: + compatible: + const: nvidia,tegra186-emc + then: + properties: + reg: + maxItems: 1 + + - if: + properties: + compatible: + const: nvidia,tegra194-emc + then: + properties: + reg: + minItems: 2 + + - if: + properties: + compatible: + const: nvidia,tegra234-emc + then: + properties: + reg: + minItems: 2 + + additionalProperties: false + + required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - "#interconnect-cells" + - nvidia,bpmp + +allOf: + - if: + properties: + compatible: + const: nvidia,tegra186-mc + then: + properties: + reg: + maxItems: 6 + description: 5 memory controller channels and 1 for stream-id registers + + reg-names: + items: + - const: sid + - const: broadcast + - const: ch0 + - const: ch1 + - const: ch2 + - const: ch3 + + - if: + properties: + compatible: + const: nvidia,tegra194-mc + then: + properties: + reg: + minItems: 18 + description: 17 memory controller channels and 1 for stream-id registers + + reg-names: + items: + - const: sid + - const: broadcast + - const: ch0 + - const: ch1 + - const: ch2 + - const: ch3 + - const: ch4 + - const: ch5 + - const: ch6 + - const: ch7 + - const: ch8 + - const: ch9 + - const: ch10 + - const: ch11 + - const: ch12 + - const: ch13 + - const: ch14 + - const: ch15 + + - if: + properties: + compatible: + const: nvidia,tegra234-mc + then: + properties: + reg: + minItems: 18 + description: 17 memory controller channels and 1 for stream-id registers + + reg-names: + items: + - const: sid + - const: broadcast + - const: ch0 + - const: ch1 + - const: ch2 + - const: ch3 + - const: ch4 + - const: ch5 + - const: ch6 + - const: ch7 + - const: ch8 + - const: ch9 + - const: ch10 + - const: ch11 + - const: ch12 + - const: ch13 + - const: ch14 + - const: ch15 + +additionalProperties: false + +required: + - compatible + - reg + - reg-names + - interrupts + - "#address-cells" + - "#size-cells" + +examples: + - | + #include <dt-bindings/clock/tegra186-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + memory-controller@2c00000 { + compatible = "nvidia,tegra186-mc"; + reg = <0x0 0x02c00000 0x0 0x10000>, /* MC-SID */ + <0x0 0x02c10000 0x0 0x10000>, /* Broadcast channel */ + <0x0 0x02c20000 0x0 0x10000>, /* MC0 */ + <0x0 0x02c30000 0x0 0x10000>, /* MC1 */ + <0x0 0x02c40000 0x0 0x10000>, /* MC2 */ + <0x0 0x02c50000 0x0 0x10000>; /* MC3 */ + reg-names = "sid", "broadcast", "ch0", "ch1", "ch2", "ch3"; + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0x0 0x02c00000 0x0 0x02c00000 0x0 0xb0000>; + + /* + * Memory clients have access to all 40 bits that the memory + * controller can address. + */ + dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x0>; + + external-memory-controller@2c60000 { + compatible = "nvidia,tegra186-emc"; + reg = <0x0 0x02c60000 0x0 0x50000>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bpmp TEGRA186_CLK_EMC>; + clock-names = "emc"; + + #interconnect-cells = <0>; + + nvidia,bpmp = <&bpmp>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file mode 100644 index 000000000..2fa44951c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml @@ -0,0 +1,249 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra20-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra20 SoC External Memory Controller + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + The External Memory Controller (EMC) interfaces with the off-chip SDRAM to + service the request stream sent from Memory Controller. The EMC also has + various performance-affecting settings beyond the obvious SDRAM configuration + parameters and initialization settings. Tegra20 EMC supports multiple JEDEC + standard protocols: DDR1, LPDDR2 and DDR2. + +properties: + compatible: + const: nvidia,tegra20-emc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#interconnect-cells": + const: 0 + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle of the Memory Controller node. + + power-domains: + maxItems: 1 + description: + Phandle of the SoC "core" power domain. + + operating-points-v2: + description: + Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC process ID mask. + + nvidia,use-ram-code: + type: boolean + description: + If present, the emc-tables@ sub-nodes will be addressed. + +$defs: + emc-table: + type: object + properties: + compatible: + const: nvidia,tegra20-emc-table + + clock-frequency: + description: + Memory clock rate in kHz. + minimum: 1000 + maximum: 900000 + + reg: + maxItems: 1 + description: + Either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). + + nvidia,emc-registers: + description: + EMC timing characterization data. These are the registers + (see section "15.4.1 EMC Registers" in the TRM) whose values + need to be specified, according to the board documentation. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: EMC_RC + - description: EMC_RFC + - description: EMC_RAS + - description: EMC_RP + - description: EMC_R2W + - description: EMC_W2R + - description: EMC_R2P + - description: EMC_W2P + - description: EMC_RD_RCD + - description: EMC_WR_RCD + - description: EMC_RRD + - description: EMC_REXT + - description: EMC_WDV + - description: EMC_QUSE + - description: EMC_QRST + - description: EMC_QSAFE + - description: EMC_RDV + - description: EMC_REFRESH + - description: EMC_BURST_REFRESH_NUM + - description: EMC_PDEX2WR + - description: EMC_PDEX2RD + - description: EMC_PCHG2PDEN + - description: EMC_ACT2PDEN + - description: EMC_AR2PDEN + - description: EMC_RW2PDEN + - description: EMC_TXSR + - description: EMC_TCKE + - description: EMC_TFAW + - description: EMC_TRPAB + - description: EMC_TCLKSTABLE + - description: EMC_TCLKSTOP + - description: EMC_TREFBW + - description: EMC_QUSE_EXTRA + - description: EMC_FBIO_CFG6 + - description: EMC_ODT_WRITE + - description: EMC_ODT_READ + - description: EMC_FBIO_CFG5 + - description: EMC_CFG_DIG_DLL + - description: EMC_DLL_XFORM_DQS + - description: EMC_DLL_XFORM_QUSE + - description: EMC_ZCAL_REF_CNT + - description: EMC_ZCAL_WAIT_CNT + - description: EMC_AUTO_CAL_INTERVAL + - description: EMC_CFG_CLKTRIM_0 + - description: EMC_CFG_CLKTRIM_1 + - description: EMC_CFG_CLKTRIM_2 + + required: + - clock-frequency + - compatible + - reg + - nvidia,emc-registers + + additionalProperties: false + +patternProperties: + "^emc-table@[0-9]+$": + $ref: "#/$defs/emc-table" + + "^emc-tables@[a-z0-9-]+$": + type: object + properties: + reg: + maxItems: 1 + description: + An opaque enumerator to tell different tables apart. + + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value of RAM_CODE this timing set is used for. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + lpddr2: + $ref: "ddr/jedec,lpddr2.yaml#" + type: object + + patternProperties: + "^emc-table@[0-9]+$": + $ref: "#/$defs/emc-table" + + oneOf: + - required: + - nvidia,ram-code + + - required: + - lpddr2 + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - nvidia,memory-controller + - "#interconnect-cells" + - operating-points-v2 + +additionalProperties: false + +examples: + - | + external-memory-controller@7000f400 { + compatible = "nvidia,tegra20-emc"; + reg = <0x7000f400 0x400>; + interrupts = <0 78 4>; + clocks = <&clock_controller 57>; + + nvidia,memory-controller = <&mc>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + + #interconnect-cells = <0>; + #address-cells = <1>; + #size-cells = <0>; + + nvidia,use-ram-code; + + emc-tables@0 { + nvidia,ram-code = <0>; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + emc-table@333000 { + reg = <333000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = <333000>; + nvidia,emc-registers = <0x00000018 0x00000033 + 0x00000012 0x00000004 0x00000004 0x00000005 + 0x00000003 0x0000000c 0x00000006 0x00000006 + 0x00000003 0x00000001 0x00000004 0x00000005 + 0x00000004 0x00000009 0x0000000d 0x00000bff + 0x00000000 0x00000003 0x00000003 0x00000006 + 0x00000006 0x00000001 0x00000011 0x000000c8 + 0x00000003 0x0000000e 0x00000007 0x00000008 + 0x00000002 0x00000000 0x00000000 0x00000002 + 0x00000000 0x00000000 0x00000083 0xf0440303 + 0x007fe010 0x00001414 0x00000000 0x00000000 + 0x00000000 0x00000000 0x00000000 0x00000000>; + }; + }; + + emc-tables@1 { + reg = <1>; + + lpddr2 { + compatible = "elpida,B8132B2PB-6D-F", "jedec,lpddr2-s4"; + revision-id1 = <1>; + density = <2048>; + io-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.yaml new file mode 100644 index 000000000..55caf6905 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra20-mc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra20 SoC Memory Controller + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + The Tegra20 Memory Controller merges request streams from various client + interfaces into request stream(s) for the various memory target devices, + and returns response data to the various clients. The Memory Controller + has a configurable arbitration algorithm to allow the user to fine-tune + performance among the various clients. + + Tegra20 Memory Controller includes the GART (Graphics Address Relocation + Table) which allows Memory Controller to provide a linear view of a + fragmented memory pages. + +properties: + compatible: + const: nvidia,tegra20-mc-gart + + reg: + items: + - description: controller registers + - description: GART registers + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mc + + interrupts: + maxItems: 1 + + "#reset-cells": + const: 1 + + "#iommu-cells": + const: 0 + + "#interconnect-cells": + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - "#reset-cells" + - "#iommu-cells" + - "#interconnect-cells" + +additionalProperties: false + +examples: + - | + memory-controller@7000f000 { + compatible = "nvidia,tegra20-mc-gart"; + reg = <0x7000f000 0x400>, /* Controller registers */ + <0x58000000 0x02000000>; /* GART aperture */ + clocks = <&clock_controller 32>; + clock-names = "mc"; + + interrupts = <0 77 4>; + + #iommu-cells = <0>; + #reset-cells = <1>; + #interconnect-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra210-emc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra210-emc.yaml new file mode 100644 index 000000000..bc8477e7a --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra210-emc.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra210-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra210 SoC External Memory Controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The EMC interfaces with the off-chip SDRAM to service the request stream + sent from the memory controller. + +properties: + compatible: + const: nvidia,tegra210-emc + + reg: + maxItems: 3 + + clocks: + items: + - description: external memory clock + + clock-names: + items: + - const: emc + + interrupts: + items: + - description: EMC general interrupt + + memory-region: + maxItems: 1 + description: + phandle to a reserved memory region describing the table of EMC + frequencies trained by the firmware + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle of the memory controller node + +required: + - compatible + - reg + - clocks + - clock-names + - nvidia,memory-controller + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/tegra210-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + emc_table: emc-table@83400000 { + compatible = "nvidia,tegra210-emc-table"; + reg = <0x83400000 0x10000>; + }; + }; + + external-memory-controller@7001b000 { + compatible = "nvidia,tegra210-emc"; + reg = <0x7001b000 0x1000>, + <0x7001e000 0x1000>, + <0x7001f000 0x1000>; + clocks = <&tegra_car TEGRA210_CLK_EMC>; + clock-names = "emc"; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + memory-region = <&emc_table>; + nvidia,memory-controller = <&mc>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.yaml new file mode 100644 index 000000000..fb6af14cb --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-emc.yaml @@ -0,0 +1,355 @@ +# SPDX-License-Identifier: (GPL-2.0) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra30-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra30 SoC External Memory Controller + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + The EMC interfaces with the off-chip SDRAM to service the request stream + sent from Memory Controller. The EMC also has various performance-affecting + settings beyond the obvious SDRAM configuration parameters and initialization + settings. Tegra30 EMC supports multiple JEDEC standard protocols: LPDDR2, + LPDDR3, and DDR3. + +properties: + compatible: + const: nvidia,tegra30-emc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interconnect-cells": + const: 0 + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle of the Memory Controller node. + + power-domains: + maxItems: 1 + description: + Phandle of the SoC "core" power domain. + + operating-points-v2: + description: + Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC speedo ID mask. + +patternProperties: + "^emc-timings-[0-9]+$": + type: object + properties: + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value of RAM_CODE this timing set is used for. + + patternProperties: + "^timing-[0-9]+$": + type: object + properties: + clock-frequency: + description: + Memory clock rate in Hz. + minimum: 1000000 + maximum: 900000000 + + nvidia,emc-auto-cal-interval: + description: + Pad calibration interval in microseconds. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 2097151 + + nvidia,emc-mode-1: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Mode Register 1. + + nvidia,emc-mode-2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Mode Register 2. + + nvidia,emc-mode-reset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Mode Register 0. + + nvidia,emc-zcal-cnt-long: + description: + Number of EMC clocks to wait before issuing any commands after + sending ZCAL_MRW_CMD. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1023 + + nvidia,emc-cfg-dyn-self-ref: + type: boolean + description: + Dynamic self-refresh enabled. + + nvidia,emc-cfg-periodic-qrst: + type: boolean + description: + FBIO "read" FIFO periodic resetting enabled. + + nvidia,emc-configuration: + description: + EMC timing characterization data. These are the registers + (see section "18.13.2 EMC Registers" in the TRM) whose values + need to be specified, according to the board documentation. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: EMC_RC + - description: EMC_RFC + - description: EMC_RAS + - description: EMC_RP + - description: EMC_R2W + - description: EMC_W2R + - description: EMC_R2P + - description: EMC_W2P + - description: EMC_RD_RCD + - description: EMC_WR_RCD + - description: EMC_RRD + - description: EMC_REXT + - description: EMC_WEXT + - description: EMC_WDV + - description: EMC_QUSE + - description: EMC_QRST + - description: EMC_QSAFE + - description: EMC_RDV + - description: EMC_REFRESH + - description: EMC_BURST_REFRESH_NUM + - description: EMC_PRE_REFRESH_REQ_CNT + - description: EMC_PDEX2WR + - description: EMC_PDEX2RD + - description: EMC_PCHG2PDEN + - description: EMC_ACT2PDEN + - description: EMC_AR2PDEN + - description: EMC_RW2PDEN + - description: EMC_TXSR + - description: EMC_TXSRDLL + - description: EMC_TCKE + - description: EMC_TFAW + - description: EMC_TRPAB + - description: EMC_TCLKSTABLE + - description: EMC_TCLKSTOP + - description: EMC_TREFBW + - description: EMC_QUSE_EXTRA + - description: EMC_FBIO_CFG6 + - description: EMC_ODT_WRITE + - description: EMC_ODT_READ + - description: EMC_FBIO_CFG5 + - description: EMC_CFG_DIG_DLL + - description: EMC_CFG_DIG_DLL_PERIOD + - description: EMC_DLL_XFORM_DQS0 + - description: EMC_DLL_XFORM_DQS1 + - description: EMC_DLL_XFORM_DQS2 + - description: EMC_DLL_XFORM_DQS3 + - description: EMC_DLL_XFORM_DQS4 + - description: EMC_DLL_XFORM_DQS5 + - description: EMC_DLL_XFORM_DQS6 + - description: EMC_DLL_XFORM_DQS7 + - description: EMC_DLL_XFORM_QUSE0 + - description: EMC_DLL_XFORM_QUSE1 + - description: EMC_DLL_XFORM_QUSE2 + - description: EMC_DLL_XFORM_QUSE3 + - description: EMC_DLL_XFORM_QUSE4 + - description: EMC_DLL_XFORM_QUSE5 + - description: EMC_DLL_XFORM_QUSE6 + - description: EMC_DLL_XFORM_QUSE7 + - description: EMC_DLI_TRIM_TXDQS0 + - description: EMC_DLI_TRIM_TXDQS1 + - description: EMC_DLI_TRIM_TXDQS2 + - description: EMC_DLI_TRIM_TXDQS3 + - description: EMC_DLI_TRIM_TXDQS4 + - description: EMC_DLI_TRIM_TXDQS5 + - description: EMC_DLI_TRIM_TXDQS6 + - description: EMC_DLI_TRIM_TXDQS7 + - description: EMC_DLL_XFORM_DQ0 + - description: EMC_DLL_XFORM_DQ1 + - description: EMC_DLL_XFORM_DQ2 + - description: EMC_DLL_XFORM_DQ3 + - description: EMC_XM2CMDPADCTRL + - description: EMC_XM2DQSPADCTRL2 + - description: EMC_XM2DQPADCTRL2 + - description: EMC_XM2CLKPADCTRL + - description: EMC_XM2COMPPADCTRL + - description: EMC_XM2VTTGENPADCTRL + - description: EMC_XM2VTTGENPADCTRL2 + - description: EMC_XM2QUSEPADCTRL + - description: EMC_XM2DQSPADCTRL3 + - description: EMC_CTT_TERM_CTRL + - description: EMC_ZCAL_INTERVAL + - description: EMC_ZCAL_WAIT_CNT + - description: EMC_MRS_WAIT_CNT + - description: EMC_AUTO_CAL_CONFIG + - description: EMC_CTT + - description: EMC_CTT_DURATION + - description: EMC_DYN_SELF_REF_CONTROL + - description: EMC_FBIO_SPARE + - description: EMC_CFG_RSV + + required: + - clock-frequency + - nvidia,emc-auto-cal-interval + - nvidia,emc-mode-1 + - nvidia,emc-mode-2 + - nvidia,emc-mode-reset + - nvidia,emc-zcal-cnt-long + - nvidia,emc-configuration + + additionalProperties: false + + required: + - nvidia,ram-code + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - nvidia,memory-controller + - "#interconnect-cells" + - operating-points-v2 + +additionalProperties: false + +examples: + - | + external-memory-controller@7000f400 { + compatible = "nvidia,tegra30-emc"; + reg = <0x7000f400 0x400>; + interrupts = <0 78 4>; + clocks = <&tegra_car 57>; + + nvidia,memory-controller = <&mc>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + + #interconnect-cells = <0>; + + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-667000000 { + clock-frequency = <667000000>; + + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200018>; + nvidia,emc-mode-reset = <0x80000b71>; + nvidia,emc-zcal-cnt-long = <0x00000040>; + nvidia,emc-cfg-periodic-qrst; + + nvidia,emc-configuration = < + 0x00000020 /* EMC_RC */ + 0x0000006a /* EMC_RFC */ + 0x00000017 /* EMC_RAS */ + 0x00000007 /* EMC_RP */ + 0x00000005 /* EMC_R2W */ + 0x0000000c /* EMC_W2R */ + 0x00000003 /* EMC_R2P */ + 0x00000011 /* EMC_W2P */ + 0x00000007 /* EMC_RD_RCD */ + 0x00000007 /* EMC_WR_RCD */ + 0x00000002 /* EMC_RRD */ + 0x00000001 /* EMC_REXT */ + 0x00000000 /* EMC_WEXT */ + 0x00000007 /* EMC_WDV */ + 0x0000000a /* EMC_QUSE */ + 0x00000009 /* EMC_QRST */ + 0x0000000b /* EMC_QSAFE */ + 0x00000011 /* EMC_RDV */ + 0x00001412 /* EMC_REFRESH */ + 0x00000000 /* EMC_BURST_REFRESH_NUM */ + 0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */ + 0x00000002 /* EMC_PDEX2WR */ + 0x0000000e /* EMC_PDEX2RD */ + 0x00000001 /* EMC_PCHG2PDEN */ + 0x00000000 /* EMC_ACT2PDEN */ + 0x0000000c /* EMC_AR2PDEN */ + 0x00000016 /* EMC_RW2PDEN */ + 0x00000072 /* EMC_TXSR */ + 0x00000200 /* EMC_TXSRDLL */ + 0x00000005 /* EMC_TCKE */ + 0x00000015 /* EMC_TFAW */ + 0x00000000 /* EMC_TRPAB */ + 0x00000006 /* EMC_TCLKSTABLE */ + 0x00000007 /* EMC_TCLKSTOP */ + 0x00001453 /* EMC_TREFBW */ + 0x0000000b /* EMC_QUSE_EXTRA */ + 0x00000006 /* EMC_FBIO_CFG6 */ + 0x00000000 /* EMC_ODT_WRITE */ + 0x00000000 /* EMC_ODT_READ */ + 0x00005088 /* EMC_FBIO_CFG5 */ + 0xf00b0191 /* EMC_CFG_DIG_DLL */ + 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ + 0x00000008 /* EMC_DLL_XFORM_DQS0 */ + 0x00000008 /* EMC_DLL_XFORM_DQS1 */ + 0x00000008 /* EMC_DLL_XFORM_DQS2 */ + 0x00000008 /* EMC_DLL_XFORM_DQS3 */ + 0x0000000a /* EMC_DLL_XFORM_DQS4 */ + 0x0000000a /* EMC_DLL_XFORM_DQS5 */ + 0x0000000a /* EMC_DLL_XFORM_DQS6 */ + 0x0000000a /* EMC_DLL_XFORM_DQS7 */ + 0x00018000 /* EMC_DLL_XFORM_QUSE0 */ + 0x00018000 /* EMC_DLL_XFORM_QUSE1 */ + 0x00018000 /* EMC_DLL_XFORM_QUSE2 */ + 0x00018000 /* EMC_DLL_XFORM_QUSE3 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ + 0x0000000a /* EMC_DLL_XFORM_DQ0 */ + 0x0000000a /* EMC_DLL_XFORM_DQ1 */ + 0x0000000a /* EMC_DLL_XFORM_DQ2 */ + 0x0000000a /* EMC_DLL_XFORM_DQ3 */ + 0x000002a0 /* EMC_XM2CMDPADCTRL */ + 0x0800013d /* EMC_XM2DQSPADCTRL2 */ + 0x22220000 /* EMC_XM2DQPADCTRL2 */ + 0x77fff884 /* EMC_XM2CLKPADCTRL */ + 0x01f1f501 /* EMC_XM2COMPPADCTRL */ + 0x07077404 /* EMC_XM2VTTGENPADCTRL */ + 0x54000000 /* EMC_XM2VTTGENPADCTRL2 */ + 0x080001e8 /* EMC_XM2QUSEPADCTRL */ + 0x0c000021 /* EMC_XM2DQSPADCTRL3 */ + 0x00000802 /* EMC_CTT_TERM_CTRL */ + 0x00020000 /* EMC_ZCAL_INTERVAL */ + 0x00000100 /* EMC_ZCAL_WAIT_CNT */ + 0x0155000c /* EMC_MRS_WAIT_CNT */ + 0xa0f10000 /* EMC_AUTO_CAL_CONFIG */ + 0x00000000 /* EMC_CTT */ + 0x00000000 /* EMC_CTT_DURATION */ + 0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */ + 0xe8000000 /* EMC_FBIO_SPARE */ + 0xff00ff49 /* EMC_CFG_RSV */ + >; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.yaml b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.yaml new file mode 100644 index 000000000..5436e6d42 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.yaml @@ -0,0 +1,172 @@ +# SPDX-License-Identifier: (GPL-2.0) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra30-mc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra30 SoC Memory Controller + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + Tegra30 Memory Controller architecturally consists of the following parts: + + Arbitration Domains, which can handle a single request or response per + clock from a group of clients. Typically, a system has a single Arbitration + Domain, but an implementation may divide the client space into multiple + Arbitration Domains to increase the effective system bandwidth. + + Protocol Arbiter, which manage a related pool of memory devices. A system + may have a single Protocol Arbiter or multiple Protocol Arbiters. + + Memory Crossbar, which routes request and responses between Arbitration + Domains and Protocol Arbiters. In the simplest version of the system, the + Memory Crossbar is just a pass through between a single Arbitration Domain + and a single Protocol Arbiter. + + Global Resources, which include things like configuration registers which + are shared across the Memory Subsystem. + + The Tegra30 Memory Controller handles memory requests from internal clients + and arbitrates among them to allocate memory bandwidth for DDR3L and LPDDR2 + SDRAMs. + +properties: + compatible: + const: nvidia,tegra30-mc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mc + + interrupts: + maxItems: 1 + + "#reset-cells": + const: 1 + + "#iommu-cells": + const: 1 + + "#interconnect-cells": + const: 1 + +patternProperties: + "^emc-timings-[0-9]+$": + type: object + properties: + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value of RAM_CODE this timing set is used for. + + patternProperties: + "^timing-[0-9]+$": + type: object + properties: + clock-frequency: + description: + Memory clock rate in Hz. + minimum: 1000000 + maximum: 900000000 + + nvidia,emem-configuration: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Values to be written to the EMEM register block. See section + "18.13.1 MC Registers" in the TRM. + items: + - description: MC_EMEM_ARB_CFG + - description: MC_EMEM_ARB_OUTSTANDING_REQ + - description: MC_EMEM_ARB_TIMING_RCD + - description: MC_EMEM_ARB_TIMING_RP + - description: MC_EMEM_ARB_TIMING_RC + - description: MC_EMEM_ARB_TIMING_RAS + - description: MC_EMEM_ARB_TIMING_FAW + - description: MC_EMEM_ARB_TIMING_RRD + - description: MC_EMEM_ARB_TIMING_RAP2PRE + - description: MC_EMEM_ARB_TIMING_WAP2PRE + - description: MC_EMEM_ARB_TIMING_R2R + - description: MC_EMEM_ARB_TIMING_W2W + - description: MC_EMEM_ARB_TIMING_R2W + - description: MC_EMEM_ARB_TIMING_W2R + - description: MC_EMEM_ARB_DA_TURNS + - description: MC_EMEM_ARB_DA_COVERS + - description: MC_EMEM_ARB_MISC0 + - description: MC_EMEM_ARB_RING1_THROTTLE + + required: + - clock-frequency + - nvidia,emem-configuration + + additionalProperties: false + + required: + - nvidia,ram-code + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - "#reset-cells" + - "#iommu-cells" + - "#interconnect-cells" + +additionalProperties: false + +examples: + - | + memory-controller@7000f000 { + compatible = "nvidia,tegra30-mc"; + reg = <0x7000f000 0x400>; + clocks = <&tegra_car 32>; + clock-names = "mc"; + + interrupts = <0 77 4>; + + #iommu-cells = <1>; + #reset-cells = <1>; + #interconnect-cells = <1>; + + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-667000000 { + clock-frequency = <667000000>; + + nvidia,emem-configuration = < + 0x0000000a /* MC_EMEM_ARB_CFG */ + 0xc0000079 /* MC_EMEM_ARB_OUTSTANDING_REQ */ + 0x00000003 /* MC_EMEM_ARB_TIMING_RCD */ + 0x00000004 /* MC_EMEM_ARB_TIMING_RP */ + 0x00000010 /* MC_EMEM_ARB_TIMING_RC */ + 0x0000000b /* MC_EMEM_ARB_TIMING_RAS */ + 0x0000000a /* MC_EMEM_ARB_TIMING_FAW */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ + 0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */ + 0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */ + 0x00000002 /* MC_EMEM_ARB_TIMING_R2R */ + 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ + 0x00000004 /* MC_EMEM_ARB_TIMING_R2W */ + 0x00000008 /* MC_EMEM_ARB_TIMING_W2R */ + 0x08040202 /* MC_EMEM_ARB_DA_TURNS */ + 0x00130b10 /* MC_EMEM_ARB_DA_COVERS */ + 0x70ea1f11 /* MC_EMEM_ARB_MISC0 */ + 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ + >; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/qca,ath79-ddr-controller.yaml b/Documentation/devicetree/bindings/memory-controllers/qca,ath79-ddr-controller.yaml new file mode 100644 index 000000000..0c511ab90 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/qca,ath79-ddr-controller.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/qca,ath79-ddr-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros AR7xxx/AR9xxx DDR controller + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: | + The DDR controller of the AR7xxx and AR9xxx families provides an interface to + flush the FIFO between various devices and the DDR. This is mainly used by + the IRQ controller to flush the FIFO before running the interrupt handler of + such devices. + +properties: + compatible: + oneOf: + - items: + - const: qca,ar9132-ddr-controller + - const: qca,ar7240-ddr-controller + - items: + - enum: + - qca,ar7100-ddr-controller + - qca,ar7240-ddr-controller + + "#qca,ddr-wb-channel-cells": + description: | + Specifies the number of cells needed to encode the write buffer channel + index. + $ref: /schemas/types.yaml#/definitions/uint32 + const: 1 + + reg: + maxItems: 1 + +required: + - compatible + - "#qca,ddr-wb-channel-cells" + - reg + +additionalProperties: false + +examples: + - | + ddr_ctrl: memory-controller@18000000 { + compatible = "qca,ar9132-ddr-controller", + "qca,ar7240-ddr-controller"; + reg = <0x18000000 0x100>; + + #qca,ddr-wb-channel-cells = <1>; + }; + + interrupt-controller { + // ... + qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>; + qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>, + <&ddr_ctrl 0>, <&ddr_ctrl 1>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.yaml new file mode 100644 index 000000000..7056ccb7e --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/memory-controllers/renesas,dbsc.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas DDR Bus Controllers + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +description: | + Renesas SoCs contain one or more memory controllers. These memory + controllers differ from one SoC variant to another, and are called by + different names, e.g. "DDR Bus Controller (DBSC)", "DDR3 Bus State Controller + (DBSC3)", or "SDRAM Bus State Controller (SBSC)"). + +properties: + compatible: + enum: + - renesas,dbsc-r8a73a4 # R-Mobile APE6 + - renesas,dbsc3-r8a7740 # R-Mobile A1 + - renesas,sbsc-sh73a0 # SH-Mobile AG5 + + reg: + maxItems: 1 + + interrupts: + maxItems: 2 + + interrupt-names: + items: + - const: sec # secure interrupt + - const: temp # normal (temperature) interrupt + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + sbsc1: memory-controller@fe400000 { + compatible = "renesas,sbsc-sh73a0"; + reg = <0xfe400000 0x400>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "sec", "temp"; + power-domains = <&pd_a4bc0>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml new file mode 100644 index 000000000..645249ea2 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/renesas,rpc-if.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Reduced Pin Count Interface (RPC-IF) + +maintainers: + - Sergei Shtylyov <sergei.shtylyov@gmail.com> + +description: | + Renesas RPC-IF allows a SPI flash or HyperFlash connected to the SoC to + be accessed via the external address space read mode or the manual mode. + + The flash chip itself should be represented by a subnode of the RPC-IF node. + The flash interface is selected based on the "compatible" property of this + subnode: + - if it contains "jedec,spi-nor", then SPI is used; + - if it contains "cfi-flash", then HyperFlash is used. + +allOf: + - $ref: "/schemas/spi/spi-controller.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r8a774a1-rpc-if # RZ/G2M + - renesas,r8a774b1-rpc-if # RZ/G2N + - renesas,r8a774c0-rpc-if # RZ/G2E + - renesas,r8a774e1-rpc-if # RZ/G2H + - renesas,r8a7795-rpc-if # R-Car H3 + - renesas,r8a7796-rpc-if # R-Car M3-W + - renesas,r8a77961-rpc-if # R-Car M3-W+ + - renesas,r8a77965-rpc-if # R-Car M3-N + - renesas,r8a77970-rpc-if # R-Car V3M + - renesas,r8a77980-rpc-if # R-Car V3H + - renesas,r8a77990-rpc-if # R-Car E3 + - renesas,r8a77995-rpc-if # R-Car D3 + - renesas,r8a779a0-rpc-if # R-Car V3U + - const: renesas,rcar-gen3-rpc-if # a generic R-Car gen3 or RZ/G2{E,H,M,N} device + + - items: + - enum: + - renesas,r9a07g043-rpc-if # RZ/G2UL + - renesas,r9a07g044-rpc-if # RZ/G2{L,LC} + - renesas,r9a07g054-rpc-if # RZ/V2L + - const: renesas,rzg2l-rpc-if + + reg: + items: + - description: RPC-IF registers + - description: direct mapping read mode area + - description: write buffer area + + reg-names: + items: + - const: regs + - const: dirmap + - const: wbuf + + clocks: true + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +patternProperties: + "flash@[0-9a-f]+$": + type: object + properties: + compatible: + contains: + enum: + - cfi-flash + - jedec,spi-nor + +required: + - compatible + - reg + - reg-names + - clocks + - power-domains + - resets + - '#address-cells' + - '#size-cells' + +if: + properties: + compatible: + contains: + enum: + - renesas,rzg2l-rpc-if +then: + properties: + clocks: + items: + - description: SPI Multi IO Register access clock (SPI_CLK2) + - description: SPI Multi IO Main clock (SPI_CLK). + +else: + properties: + clocks: + maxItems: 1 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/renesas-cpg-mssr.h> + #include <dt-bindings/power/r8a77995-sysc.h> + + spi@ee200000 { + compatible = "renesas,r8a77995-rpc-if", "renesas,rcar-gen3-rpc-if"; + reg = <0xee200000 0x200>, + <0x08000000 0x4000000>, + <0xee208000 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + clocks = <&cpg CPG_MOD 917>; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/rockchip,rk3399-dmc.yaml b/Documentation/devicetree/bindings/memory-controllers/rockchip,rk3399-dmc.yaml new file mode 100644 index 000000000..fb4920397 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/rockchip,rk3399-dmc.yaml @@ -0,0 +1,384 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# %YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/rockchip,rk3399-dmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip rk3399 DMC (Dynamic Memory Controller) device + +maintainers: + - Brian Norris <briannorris@chromium.org> + +properties: + compatible: + enum: + - rockchip,rk3399-dmc + + devfreq-events: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Node to get DDR loading. Refer to + Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt. + + clocks: + maxItems: 1 + + clock-names: + items: + - const: dmc_clk + + operating-points-v2: true + + center-supply: + description: + DMC regulator supply. + + rockchip,pmu: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the syscon managing the "PMU general register files". + + interrupts: + maxItems: 1 + description: + The CPU interrupt number. It should be a DCF interrupt. When DDR DVFS + finishes, a DCF interrupt is triggered. + + rockchip,ddr3_speed_bin: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + For values, reference include/dt-bindings/clock/rk3399-ddr.h. Selects the + DDR3 cl-trp-trcd type. It must be set according to "Speed Bin" in DDR3 + datasheet; DO NOT use a smaller "Speed Bin" than specified for the DDR3 + being used. + + rockchip,pd_idle: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Configure the PD_IDLE value. Defines the power-down idle period in which + memories are placed into power-down mode if bus is idle for PD_IDLE DFI + clock cycles. + See also rockchip,pd-idle-ns. + + rockchip,sr_idle: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Configure the SR_IDLE value. Defines the self-refresh idle period in + which memories are placed into self-refresh mode if bus is idle for + SR_IDLE * 1024 DFI clock cycles (DFI clocks freq is half of DRAM clock). + See also rockchip,sr-idle-ns. + default: 0 + + rockchip,sr_mc_gate_idle: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Defines the memory self-refresh and controller clock gating idle period. + Memories are placed into self-refresh mode and memory controller clock + arg gating started if bus is idle for sr_mc_gate_idle*1024 DFI clock + cycles. + See also rockchip,sr-mc-gate-idle-ns. + + rockchip,srpd_lite_idle: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Defines the self-refresh power down idle period in which memories are + placed into self-refresh power down mode if bus is idle for + srpd_lite_idle * 1024 DFI clock cycles. This parameter is for LPDDR4 + only. + See also rockchip,srpd-lite-idle-ns. + + rockchip,standby_idle: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Defines the standby idle period in which memories are placed into + self-refresh mode. The controller, pi, PHY and DRAM clock will be gated + if bus is idle for standby_idle * DFI clock cycles. + See also rockchip,standby-idle-ns. + + rockchip,dram_dll_dis_freq: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Defines the DDR3 DLL bypass frequency in MHz. When DDR frequency is less + than DRAM_DLL_DISB_FREQ, DDR3 DLL will be bypassed. + Note: if DLL was bypassed, the odt will also stop working. + + rockchip,phy_dll_dis_freq: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Defines the PHY dll bypass frequency in MHz (Mega Hz). When DDR frequency + is less than DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed. + Note: PHY DLL and PHY ODT are independent. + + rockchip,auto_pd_dis_freq: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Defines the auto PD disable frequency in MHz. + + rockchip,ddr3_odt_dis_freq: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1000000 # In case anyone thought this was MHz. + description: + When the DRAM type is DDR3, this parameter defines the ODT disable + frequency in Hz. When the DDR frequency is less then ddr3_odt_dis_freq, + the ODT on the DRAM side and controller side are both disabled. + + rockchip,ddr3_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is DDR3, this parameter defines the DRAM side drive + strength in ohms. + default: 40 + + rockchip,ddr3_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is DDR3, this parameter defines the DRAM side ODT + strength in ohms. + default: 120 + + rockchip,phy_ddr3_ca_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is DDR3, this parameter defines the phy side CA line + (incluing command line, address line and clock line) drive strength. + default: 40 + + rockchip,phy_ddr3_dq_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is DDR3, this parameter defines the PHY side DQ line + (including DQS/DQ/DM line) drive strength. + default: 40 + + rockchip,phy_ddr3_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is DDR3, this parameter defines the PHY side ODT + strength. + default: 240 + + rockchip,lpddr3_odt_dis_freq: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1000000 # In case anyone thought this was MHz. + description: + When the DRAM type is LPDDR3, this parameter defines then ODT disable + frequency in Hz. When DDR frequency is less then ddr3_odt_dis_freq, the + ODT on the DRAM side and controller side are both disabled. + + rockchip,lpddr3_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR3, this parameter defines the DRAM side drive + strength in ohms. + default: 34 + + rockchip,lpddr3_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR3, this parameter defines the DRAM side ODT + strength in ohms. + default: 240 + + rockchip,phy_lpddr3_ca_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR3, this parameter defines the PHY side CA line + (including command line, address line and clock line) drive strength. + default: 40 + + rockchip,phy_lpddr3_dq_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR3, this parameter defines the PHY side DQ line + (including DQS/DQ/DM line) drive strength. + default: 40 + + rockchip,phy_lpddr3_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When dram type is LPDDR3, this parameter define the phy side odt + strength, default value is 240. + + rockchip,lpddr4_odt_dis_freq: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1000000 # In case anyone thought this was MHz. + description: + When the DRAM type is LPDDR4, this parameter defines the ODT disable + frequency in Hz. When the DDR frequency is less then ddr3_odt_dis_freq, + the ODT on the DRAM side and controller side are both disabled. + + rockchip,lpddr4_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the DRAM side drive + strength in ohms. + default: 60 + + rockchip,lpddr4_dq_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on + DQS/DQ line strength in ohms. + default: 40 + + rockchip,lpddr4_ca_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on + CA line strength in ohms. + default: 40 + + rockchip,phy_lpddr4_ca_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the PHY side CA line + (including command address line) drive strength. + default: 40 + + rockchip,phy_lpddr4_ck_cs_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the PHY side clock + line and CS line drive strength. + default: 80 + + rockchip,phy_lpddr4_dq_drv: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the PHY side DQ line + (including DQS/DQ/DM line) drive strength. + default: 80 + + rockchip,phy_lpddr4_odt: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + description: + When the DRAM type is LPDDR4, this parameter defines the PHY side ODT + strength. + default: 60 + + rockchip,pd-idle-ns: + description: + Configure the PD_IDLE value in nanoseconds. Defines the power-down idle + period in which memories are placed into power-down mode if bus is idle + for PD_IDLE nanoseconds. + + rockchip,sr-idle-ns: + description: + Configure the SR_IDLE value in nanoseconds. Defines the self-refresh idle + period in which memories are placed into self-refresh mode if bus is idle + for SR_IDLE nanoseconds. + default: 0 + + rockchip,sr-mc-gate-idle-ns: + description: + Defines the memory self-refresh and controller clock gating idle period in nanoseconds. + Memories are placed into self-refresh mode and memory controller clock + arg gating started if bus is idle for sr_mc_gate_idle nanoseconds. + + rockchip,srpd-lite-idle-ns: + description: + Defines the self-refresh power down idle period in which memories are + placed into self-refresh power down mode if bus is idle for + srpd_lite_idle nanoseonds. This parameter is for LPDDR4 only. + + rockchip,standby-idle-ns: + description: + Defines the standby idle period in which memories are placed into + self-refresh mode. The controller, pi, PHY and DRAM clock will be gated + if bus is idle for standby_idle nanoseconds. + + rockchip,pd-idle-dis-freq-hz: + description: + Defines the power-down idle disable frequency in Hz. When the DDR + frequency is greater than pd-idle-dis-freq, power-down idle is disabled. + See also rockchip,pd-idle-ns. + + rockchip,sr-idle-dis-freq-hz: + description: + Defines the self-refresh idle disable frequency in Hz. When the DDR + frequency is greater than sr-idle-dis-freq, self-refresh idle is + disabled. See also rockchip,sr-idle-ns. + + rockchip,sr-mc-gate-idle-dis-freq-hz: + description: + Defines the self-refresh and memory-controller clock gating disable + frequency in Hz. When the DDR frequency is greater than + sr-mc-gate-idle-dis-freq, the clock will not be gated when idle. See also + rockchip,sr-mc-gate-idle-ns. + + rockchip,srpd-lite-idle-dis-freq-hz: + description: + Defines the self-refresh power down idle disable frequency in Hz. When + the DDR frequency is greater than srpd-lite-idle-dis-freq, memory will + not be placed into self-refresh power down mode when idle. See also + rockchip,srpd-lite-idle-ns. + + rockchip,standby-idle-dis-freq-hz: + description: + Defines the standby idle disable frequency in Hz. When the DDR frequency + is greater than standby-idle-dis-freq, standby idle is disabled. See also + rockchip,standby-idle-ns. + +required: + - compatible + - devfreq-events + - clocks + - clock-names + - operating-points-v2 + - center-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + memory-controller { + compatible = "rockchip,rk3399-dmc"; + devfreq-events = <&dfi>; + rockchip,pmu = <&pmu>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_DDRC>; + clock-names = "dmc_clk"; + operating-points-v2 = <&dmc_opp_table>; + center-supply = <&ppvar_centerlogic>; + rockchip,pd-idle-ns = <160>; + rockchip,sr-idle-ns = <10240>; + rockchip,sr-mc-gate-idle-ns = <40960>; + rockchip,srpd-lite-idle-ns = <61440>; + rockchip,standby-idle-ns = <81920>; + rockchip,ddr3_odt_dis_freq = <333000000>; + rockchip,lpddr3_odt_dis_freq = <333000000>; + rockchip,lpddr4_odt_dis_freq = <333000000>; + rockchip,pd-idle-dis-freq-hz = <1000000000>; + rockchip,sr-idle-dis-freq-hz = <1000000000>; + rockchip,sr-mc-gate-idle-dis-freq-hz = <1000000000>; + rockchip,srpd-lite-idle-dis-freq-hz = <0>; + rockchip,standby-idle-dis-freq-hz = <928000000>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml new file mode 100644 index 000000000..098348b2b --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/samsung,exynos5422-dmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: | + Samsung Exynos5422 SoC frequency and voltage scaling for Dynamic Memory + Controller device + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Lukasz Luba <lukasz.luba@arm.com> + +description: | + The Samsung Exynos5422 SoC has DMC (Dynamic Memory Controller) to which the + DRAM memory chips are connected. The driver is to monitor the controller in + runtime and switch frequency and voltage. To monitor the usage of the + controller in runtime, the driver uses the PPMU (Platform Performance + Monitoring Unit), which is able to measure the current load of the memory. + When 'userspace' governor is used for the driver, an application is able to + switch the DMC and memory frequency. + +properties: + compatible: + items: + - const: samsung,exynos5422-dmc + + clock-names: + items: + - const: fout_spll + - const: mout_sclk_spll + - const: ff_dout_spll2 + - const: fout_bpll + - const: mout_bpll + - const: sclk_bpll + - const: mout_mx_mspll_ccore + - const: mout_mclk_cdrex + + clocks: + minItems: 8 + maxItems: 8 + + devfreq-events: + $ref: '/schemas/types.yaml#/definitions/phandle-array' + minItems: 1 + maxItems: 16 + items: + maxItems: 1 + description: phandles of the PPMU events used by the controller. + + device-handle: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: | + phandle of the connected DRAM memory device. For more information please + refer to jedec,lpddr3.yaml. + + operating-points-v2: true + + interrupts: + items: + - description: DMC internal performance event counters in DREX0 + - description: DMC internal performance event counters in DREX1 + + interrupt-names: + items: + - const: drex_0 + - const: drex_1 + + reg: + items: + - description: registers of DREX0 + - description: registers of DREX1 + + samsung,syscon-clk: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: | + Phandle of the clock register set used by the controller, these registers + are used for enabling a 'pause' feature and are not exposed by clock + framework but they must be used in a safe way. The register offsets are + in the driver code and specyfic for this SoC type. + + vdd-supply: true + +required: + - compatible + - clock-names + - clocks + - devfreq-events + - device-handle + - reg + - samsung,syscon-clk + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + ppmu_dmc0_0: ppmu@10d00000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x10d00000 0x2000>; + clocks = <&clock CLK_PCLK_PPMU_DREX0_0>; + clock-names = "ppmu"; + events { + ppmu_event_dmc0_0: ppmu-event3-dmc0-0 { + event-name = "ppmu-event3-dmc0_0"; + }; + }; + }; + + memory-controller@10c20000 { + compatible = "samsung,exynos5422-dmc"; + reg = <0x10c20000 0x10000>, <0x10c30000 0x10000>; + clocks = <&clock CLK_FOUT_SPLL>, + <&clock CLK_MOUT_SCLK_SPLL>, + <&clock CLK_FF_DOUT_SPLL2>, + <&clock CLK_FOUT_BPLL>, + <&clock CLK_MOUT_BPLL>, + <&clock CLK_SCLK_BPLL>, + <&clock CLK_MOUT_MX_MSPLL_CCORE>, + <&clock CLK_MOUT_MCLK_CDREX>; + clock-names = "fout_spll", + "mout_sclk_spll", + "ff_dout_spll2", + "fout_bpll", + "mout_bpll", + "sclk_bpll", + "mout_mx_mspll_ccore", + "mout_mclk_cdrex"; + operating-points-v2 = <&dmc_opp_table>; + devfreq-events = <&ppmu_event3_dmc0_0>, <&ppmu_event3_dmc0_1>, + <&ppmu_event3_dmc1_0>, <&ppmu_event3_dmc1_1>; + device-handle = <&samsung_K3QF2F20DB>; + vdd-supply = <&buck1_reg>; + samsung,syscon-clk = <&clock>; + interrupt-parent = <&combiner>; + interrupts = <16 0>, <16 1>; + interrupt-names = "drex_0", "drex_1"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/snps,dw-umctl2-ddrc.yaml b/Documentation/devicetree/bindings/memory-controllers/snps,dw-umctl2-ddrc.yaml new file mode 100644 index 000000000..e68c43060 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/snps,dw-umctl2-ddrc.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/snps,dw-umctl2-ddrc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare Universal Multi-Protocol Memory Controller + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Manish Narani <manish.narani@xilinx.com> + - Michal Simek <michal.simek@xilinx.com> + +description: | + Synopsys DesignWare Enhanced uMCTL2 DDR Memory Controller is capable of + working with the memory devices supporting up to (LP)DDR4 protocol. It can + be equipped with SEC/DEC ECC feature if DRAM data bus width is either + 16-bits or 32-bits or 64-bits wide. + + For instance the ZynqMP DDR controller is based on the DW uMCTL2 v2.40a + controller. It has an optional SEC/DEC ECC support in 64- and 32-bits + bus width configurations. + +properties: + compatible: + oneOf: + - deprecated: true + description: Synopsys DW uMCTL2 DDR controller v3.80a + const: snps,ddrc-3.80a + - description: Synopsys DW uMCTL2 DDR controller + const: snps,dw-umctl2-ddrc + - description: Xilinx ZynqMP DDR controller v2.40a + const: xlnx,zynqmp-ddrc-2.40a + + interrupts: + description: + DW uMCTL2 DDRC IP-core provides individual IRQ signal for each event":" + ECC Corrected Error, ECC Uncorrected Error, ECC Address Protection, + Scrubber-Done signal, DFI Parity/CRC Error. Some platforms may have the + signals merged before they reach the IRQ controller or have some of them + absent in case if the corresponding feature is unavailable/disabled. + minItems: 1 + maxItems: 5 + + interrupt-names: + minItems: 1 + maxItems: 5 + oneOf: + - description: Common ECC CE/UE/Scrubber/DFI Errors IRQ + items: + - const: ecc + - description: Individual ECC CE/UE/Scrubber/DFI Errors IRQs + items: + enum: [ ecc_ce, ecc_ue, ecc_ap, ecc_sbr, dfi_e ] + + reg: + maxItems: 1 + + clocks: + description: + A standard set of the clock sources contains CSRs bus clock, AXI-ports + reference clock, DDRC core clock, Scrubber standalone clock + (synchronous to the DDRC clock). + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + enum: [ pclk, aclk, core, sbr ] + + resets: + description: + Each clock domain can have separate reset signal. + minItems: 1 + maxItems: 4 + + reset-names: + minItems: 1 + maxItems: 4 + items: + enum: [ prst, arst, core, sbr ] + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + memory-controller@fd070000 { + compatible = "xlnx,zynqmp-ddrc-2.40a"; + reg = <0xfd070000 0x30000>; + + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ecc"; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + + memory-controller@3d400000 { + compatible = "snps,dw-umctl2-ddrc"; + reg = <0x3d400000 0x400000>; + + interrupts = <147 IRQ_TYPE_LEVEL_HIGH>, <148 IRQ_TYPE_LEVEL_HIGH>, + <149 IRQ_TYPE_LEVEL_HIGH>, <150 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ecc_ce", "ecc_ue", "ecc_sbr", "dfi_e"; + + clocks = <&pclk>, <&aclk>, <&core_clk>, <&sbr_clk>; + clock-names = "pclk", "aclk", "core", "sbr"; + }; +... diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml new file mode 100644 index 000000000..6b516d389 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml @@ -0,0 +1,254 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings + +description: | + The FMC2 functional block makes the interface with: synchronous and + asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped + peripherals) and NAND flash memories. + Its main purposes are: + - to translate AXI transactions into the appropriate external device + protocol + - to meet the access time requirements of the external devices + All external devices share the addresses, data and control signals with the + controller. Each external device is accessed by means of a unique Chip + Select. The FMC2 performs only one access at a time to an external device. + +maintainers: + - Christophe Kerello <christophe.kerello@foss.st.com> + +properties: + compatible: + const: st,stm32mp1-fmc2-ebi + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + ranges: + description: | + Reflects the memory layout with four integer values per bank. Format: + <bank-number> 0 <address of the bank> <size> + +patternProperties: + "^.*@[0-4],[a-f0-9]+$": + type: object + + properties: + reg: + description: Bank number, base address and size of the device. + + st,fmc2-ebi-cs-transaction-type: + description: | + Select one of the transactions type supported + 0: Asynchronous mode 1 SRAM/FRAM. + 1: Asynchronous mode 1 PSRAM. + 2: Asynchronous mode A SRAM/FRAM. + 3: Asynchronous mode A PSRAM. + 4: Asynchronous mode 2 NOR. + 5: Asynchronous mode B NOR. + 6: Asynchronous mode C NOR. + 7: Asynchronous mode D NOR. + 8: Synchronous read synchronous write PSRAM. + 9: Synchronous read asynchronous write PSRAM. + 10: Synchronous read synchronous write NOR. + 11: Synchronous read asynchronous write NOR. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 11 + + st,fmc2-ebi-cs-cclk-enable: + description: Continuous clock enable (first bank must be configured + in synchronous mode). The FMC_CLK is generated continuously + during asynchronous and synchronous access. By default, the + FMC_CLK is only generated during synchronous access. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-mux-enable: + description: Address/Data multiplexed on databus (valid only with + NOR and PSRAM transactions type). By default, Address/Data + are not multiplexed. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-buswidth: + description: Data bus width + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 8, 16 ] + default: 16 + + st,fmc2-ebi-cs-waitpol-high: + description: Wait signal polarity (NWAIT signal active high). + By default, NWAIT is active low. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-waitcfg-enable: + description: The NWAIT signal indicates wheither the data from the + device are valid or if a wait state must be inserted when accessing + the device in synchronous mode. By default, the NWAIT signal is + active one data cycle before wait state. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-wait-enable: + description: The NWAIT signal is enabled (its level is taken into + account after the programmed latency period to insert wait states + if asserted). By default, the NWAIT signal is disabled. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-asyncwait-enable: + description: The NWAIT signal is taken into account during asynchronous + transactions. By default, the NWAIT signal is not taken into account + during asynchronous transactions. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-cpsize: + description: CRAM page size. The controller splits the burst access + when the memory page is reached. By default, no burst split when + crossing page boundary. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 128, 256, 512, 1024 ] + default: 0 + + st,fmc2-ebi-cs-byte-lane-setup-ns: + description: This property configures the byte lane setup timing + defined in nanoseconds from NBLx low to Chip Select NEx low. + + st,fmc2-ebi-cs-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed read/write + transactions. + + st,fmc2-ebi-cs-data-setup-ns: + description: This property defines the duration of the data setup phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-bus-turnaround-ns: + description: This property defines the delay in nanoseconds between the + end of current read/write transaction and the next transaction. + + st,fmc2-ebi-cs-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-clk-period-ns: + description: This property defines the FMC_CLK output signal period in + nanoseconds. + + st,fmc2-ebi-cs-data-latency-ns: + description: This property defines the data latency before reading or + writing the first data in nanoseconds. + + st,fmc2_ebi-cs-write-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed write + transactions. + + st,fmc2-ebi-cs-write-data-setup-ns: + description: This property defines the duration of the data setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-bus-turnaround-ns: + description: This property defines the delay between the end of current + write transaction and the next transaction in nanoseconds. + + st,fmc2-ebi-cs-write-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-max-low-pulse-ns: + description: This property defines the maximum chip select low pulse + duration in nanoseconds for synchronous transactions. When this timing + reaches 0, the controller splits the current access, toggles NE to + allow device refresh and restarts a new access. + + required: + - reg + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + - clocks + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + memory-controller@58002000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "st,stm32mp1-fmc2-ebi"; + reg = <0x58002000 0x1000>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + + ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ + <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ + <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ + <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ + <4 0 0x80000000 0x10000000>; /* NAND */ + + psram@0,0 { + compatible = "mtd-ram"; + reg = <0 0x00000000 0x100000>; + bank-width = <2>; + + st,fmc2-ebi-cs-transaction-type = <1>; + st,fmc2-ebi-cs-address-setup-ns = <60>; + st,fmc2-ebi-cs-data-setup-ns = <30>; + st,fmc2-ebi-cs-bus-turnaround-ns = <5>; + }; + + nand-controller@4,0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32mp1-fmc2-nfc"; + reg = <4 0x00000000 0x1000>, + <4 0x08010000 0x1000>, + <4 0x08020000 0x1000>, + <4 0x01000000 0x1000>, + <4 0x09010000 0x1000>, + <4 0x09020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml new file mode 100644 index 000000000..382ddab60 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,da8xx-ddrctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments da8xx DDR2/mDDR memory controller + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + - Krzysztof Kozlowski <krzk@kernel.org> + +description: | + Documentation: + OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +properties: + compatible: + const: ti,da850-ddr-controller + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + memory-controller@b0000000 { + compatible = "ti,da850-ddr-controller"; + reg = <0xb0000000 0xe8>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml new file mode 100644 index 000000000..6e3995bb1 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml @@ -0,0 +1,245 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: device tree bindings for children of the Texas Instruments GPMC + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + This binding is meant for the child nodes of the GPMC node. The node + represents any device connected to the GPMC bus. It may be a Flash chip, + RAM chip or Ethernet controller, etc. These properties are meant for + configuring the GPMC settings/timings and will accompany the bindings + supported by the respective device. + +properties: + reg: true + +# GPMC Timing properties for child nodes. All are optional and default to 0. + gpmc,sync-clk-ps: + description: Minimum clock period for synchronous mode + default: 0 + +# Chip-select signal timings corresponding to GPMC_CONFIG2: + gpmc,cs-on-ns: + description: Assertion time + default: 0 + + gpmc,cs-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,cs-wr-off-ns: + description: Write deassertion time + default: 0 + +# ADV signal timings corresponding to GPMC_CONFIG3: + gpmc,adv-on-ns: + description: Assertion time + default: 0 + + gpmc,adv-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,adv-wr-off-ns: + description: Write deassertion time + default: 0 + + gpmc,adv-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,adv-aad-mux-rd-off-ns: + description: Read deassertion time for AAD + default: 0 + + gpmc,adv-aad-mux-wr-off-ns: + description: Write deassertion time for AAD + default: 0 + +# WE signals timings corresponding to GPMC_CONFIG4: + gpmc,we-on-ns: + description: Assertion time + default: 0 + + gpmc,we-off-ns: + description: Deassertion time + default: 0 + +# OE signals timings corresponding to GPMC_CONFIG4: + gpmc,oe-on-ns: + description: Assertion time + default: 0 + + gpmc,oe-off-ns: + description: Deassertion time + default: 0 + + gpmc,oe-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,oe-aad-mux-off-ns: + description: Deassertion time for AAD + default: 0 + +# Access time and cycle time timings (in nanoseconds) corresponding to +# GPMC_CONFIG5: + gpmc,page-burst-access-ns: + description: Multiple access word delay + default: 0 + + gpmc,access-ns: + description: Start-cycle to first data valid delay + default: 0 + + gpmc,rd-cycle-ns: + description: Total read cycle time + default: 0 + + gpmc,wr-cycle-ns: + description: Total write cycle time + default: 0 + + gpmc,bus-turnaround-ns: + description: Turn-around time between successive accesses + default: 0 + + gpmc,cycle2cycle-delay-ns: + description: Delay between chip-select pulses + default: 0 + + gpmc,clk-activation-ns: + description: GPMC clock activation time + default: 0 + + gpmc,wait-monitoring-ns: + description: Start of wait monitoring with regard to valid data + default: 0 + +# Boolean timing parameters. If property is present, parameter is enabled +# otherwise disabled. + gpmc,adv-extra-delay: + description: ADV signal is delayed by half GPMC clock + type: boolean + + gpmc,cs-extra-delay: + description: CS signal is delayed by half GPMC clock + type: boolean + + gpmc,cycle2cycle-diffcsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to a different CS + type: boolean + + gpmc,cycle2cycle-samecsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to the same CS + type: boolean + + gpmc,oe-extra-delay: + description: OE signal is delayed by half GPMC clock + type: boolean + + gpmc,we-extra-delay: + description: WE signal is delayed by half GPMC clock + type: boolean + + gpmc,time-para-granularity: + description: Multiply all access times by 2 + type: boolean + +# The following two properties are applicable only to OMAP3+ and AM335x: + gpmc,wr-access-ns: + description: | + In synchronous write mode, for single or + burst accesses, defines the number of + GPMC_FCLK cycles from start access time + to the GPMC_CLK rising edge used by the + memory device for the first data capture. + default: 0 + + gpmc,wr-data-mux-bus-ns: + description: | + In address-data multiplex mode, specifies + the time when the first data is driven on + the address-data bus. + default: 0 + +# GPMC chip-select settings properties for child nodes. All are optional. + gpmc,burst-length: + description: Page/burst length. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 4, 8, 16] + default: 0 + + gpmc,burst-wrap: + description: Enables wrap bursting + type: boolean + + gpmc,burst-read: + description: Enables read page/burst mode + type: boolean + + gpmc,burst-write: + description: Enables write page/burst mode + type: boolean + + gpmc,device-width: + description: | + Total width of device(s) connected to a GPMC + chip-select in bytes. The GPMC supports 8-bit + and 16-bit devices and so this property must be + 1 or 2. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2] + default: 1 + + gpmc,mux-add-data: + description: | + Address and data multiplexing configuration. + Valid values are + 0 for Non multiplexed mode + 1 for address-address-data multiplexing mode and + 2 for address-data multiplexing mode. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + gpmc,sync-read: + description: | + Enables synchronous read. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,sync-write: + description: | + Enables synchronous writes. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,wait-pin: + description: | + Wait-pin used by client. Must be less than "gpmc,num-waitpins". + $ref: /schemas/types.yaml#/definitions/uint32 + + gpmc,wait-on-read: + description: Enables wait monitoring on reads. + type: boolean + + gpmc,wait-on-write: + description: Enables wait monitoring on writes. + type: boolean + +required: + - reg + +# the GPMC child will have its own native properties +additionalProperties: true diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml new file mode 100644 index 000000000..e188a4bf7 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments GPMC Memory Controller device-tree bindings + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + The GPMC is a unified memory controller dedicated for interfacing + with external memory devices like + - Asynchronous SRAM-like memories and ASICs + - Asynchronous, synchronous, and page mode burst NOR flash + - NAND flash + - Pseudo-SRAM devices + +properties: + compatible: + items: + - enum: + - ti,am3352-gpmc + - ti,am64-gpmc + - ti,omap2420-gpmc + - ti,omap2430-gpmc + - ti,omap3430-gpmc + - ti,omap4430-gpmc + + reg: + minItems: 1 + maxItems: 2 + + reg-names: + items: + - const: cfg + - const: data + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: | + Functional clock. Used for bus timing calculations and + GPMC configuration. + + clock-names: + items: + - const: fck + + power-domains: + maxItems: 1 + + dmas: + items: + - description: DMA channel for GPMC NAND prefetch + + dma-names: + items: + - const: rxtx + + "#address-cells": true + + "#size-cells": true + + gpmc,num-cs: + description: maximum number of supported chip-select lines. + $ref: /schemas/types.yaml#/definitions/uint32 + + gpmc,num-waitpins: + description: maximum number of supported wait pins. + $ref: /schemas/types.yaml#/definitions/uint32 + + ranges: + minItems: 1 + description: | + Must be set up to reflect the memory layout with four + integer values for each chip-select line in use, + <cs-number> 0 <physical address of mapping> <size> + items: + - description: NAND bank 0 + - description: NOR/SRAM bank 0 + - description: NOR/SRAM bank 1 + + '#interrupt-cells': + const: 2 + + interrupt-controller: + description: | + The GPMC driver implements and interrupt controller for + the NAND events "fifoevent" and "termcount" plus the + rising/falling edges on the GPMC_WAIT pins. + The interrupt number mapping is as follows + 0 - NAND_fifoevent + 1 - NAND_termcount + 2 - GPMC_WAIT0 pin edge + 3 - GPMC_WAIT1 pin edge, and so on. + + '#gpio-cells': + const: 2 + + gpio-controller: + description: | + The GPMC driver implements a GPIO controller for the + GPMC WAIT pins that can be used as general purpose inputs. + 0 maps to GPMC_WAIT0 pin. + + ti,hwmods: + description: + Name of the HWMOD associated with GPMC. This is for legacy + omap2/3 platforms only. + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + + ti,no-idle-on-init: + description: + Prevent idling the module at init. This is for legacy omap2/3 + platforms only. + type: boolean + deprecated: true + +patternProperties: + "@[0-7],[a-f0-9]+$": + type: object + description: | + The child device node represents the device connected to the GPMC + bus. The device can be a NAND chip, SRAM device, NOR device + or an ASIC. + $ref: "ti,gpmc-child.yaml" + + +required: + - compatible + - reg + - gpmc,num-cs + - gpmc,num-waitpins + - "#address-cells" + - "#size-cells" + +allOf: + - if: + properties: + compatible: + contains: + const: ti,am64-gpmc + then: + required: + - reg-names + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/gpio/gpio.h> + + gpmc: memory-controller@50000000 { + compatible = "ti,am3352-gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + clocks = <&l3s_clkctrl>; + clock-names = "fck"; + dmas = <&edma 52 0>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + ti,nand-xfer-type = "prefetch-dma"; + ti,nand-ecc-opt = "bch16"; + ti,elm-id = <&elm>; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt new file mode 100644 index 000000000..190437a0c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt @@ -0,0 +1,210 @@ +* Device tree bindings for Texas instruments AEMIF controller + +The Async External Memory Interface (EMIF16/AEMIF) controller is intended to +provide a glue-less interface to a variety of asynchronous memory devices like +ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories +can be accessed at any given time via four chip selects with 64M byte access +per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM +and Mobile SDR are not supported. + +Documentation: +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf + +Required properties: + +- compatible: "ti,davinci-aemif" + "ti,keystone-aemif" + "ti,da850-aemif" + +- reg: contains offset/length value for AEMIF control registers + space. + +- #address-cells: Must be 2. The partition number has to be encoded in the + first address cell and it may accept values 0..N-1 + (N - total number of partitions). It's recommended to + assign N-1 number for the control partition. The second + cell is the offset into the partition. + +- #size-cells: Must be set to 1. + +- ranges: Contains memory regions. There are two types of + ranges/partitions: + - CS-specific partition/range. If continuous, must be + set up to reflect the memory layout for 4 chipselects, + if not then additional range/partition can be added and + child device can select the proper one. + - control partition which is common for all CS + interfaces. + +- clocks: the clock feeding the controller clock. Required only + if clock tree data present in device tree. + See clock-bindings.txt + +- clock-names: clock name. It has to be "aemif". Required only if clock + tree data present in device tree, in another case don't + use it. + See clock-bindings.txt + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + See clock-bindings.txt + + +Child chip-select (cs) nodes contain the memory devices nodes connected to +such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt). +There might be board specific devices like FPGAs. + +Required child cs node properties: + +- #address-cells: Must be 2. + +- #size-cells: Must be 1. + +- ranges: Empty property indicating that child nodes can inherit + memory layout. + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + +- ti,cs-chipselect: number of chipselect. Indicates on the aemif driver + which chipselect is used for accessing the memory. For + compatibles "ti,davinci-aemif" and "ti,keystone-aemif" + it can be in range [0-3]. For compatible + "ti,da850-aemif" range is [2-5]. + +Optional child cs node properties: + +- ti,cs-bus-width: width of the asynchronous device's data bus + 8 or 16 if not preset 8 + +- ti,cs-select-strobe-mode: enable/disable select strobe mode + In select strobe mode chip select behaves as + the strobe and is active only during the strobe + period. If present then enable. + +- ti,cs-extended-wait-mode: enable/disable extended wait mode + if set, the controller monitors the EMIFWAIT pin + mapped to that chip select to determine if the + device wants to extend the strobe period. If + present then enable. + +- ti,cs-min-turnaround-ns: minimum turn around time, ns + Time between the end of one asynchronous memory + access and the start of another asynchronous + memory access. This delay is not incurred + between a read followed by read or a write + followed by a write to same chip select. + +- ti,cs-read-setup-ns: read setup width, ns + Time between the beginning of a memory cycle + and the activation of read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-strobe-ns: read strobe width, ns + Time between the activation and deactivation of + the read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-hold-ns: read hold width, ns + Time between the deactivation of the read + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-setup-ns: write setup width, ns + Time between the beginning of a memory cycle + and the activation of write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-strobe-ns: write strobe width, ns + Time between the activation and deactivation of + the write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-hold-ns: write hold width, ns + Time between the deactivation of the write + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +If any of the above parameters are absent, current parameter value will be taken +from the corresponding HW reg. + +Example for aemif, davinci nand and nor flash chip select shown below. + +memory-controller@21000a00 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&clkaemif 0>; + clock-names = "aemif"; + clock-ranges; + reg = <0x21000A00 0x00000100>; + ranges = <0 0 0x70000000 0x10000000 + 1 0 0x21000A00 0x00000100>; + /* + * Partition0: CS-specific memory range which is + * implemented as continuous physical memory region + * Partition1: control memory range + */ + + nand:cs2 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <2>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <7>; + ti,cs-read-strobe-ns = <42>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <42>; + ti,cs-write-setup-ns = <14>; + + nand@0,0x8000000 { + compatible = "ti,davinci-nand"; + reg = <0 0x8000000 0x4000000 + 1 0x0000000 0x0000100>; + /* + * Partition0, offset 0x8000000, size 0x4000000 + * Partition1, offset 0x0000000, size 0x0000100 + */ + + .. see davinci-nand.txt + }; + }; + + nor:cs0 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <0>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <8>; + ti,cs-read-strobe-ns = <40>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <40>; + ti,cs-write-setup-ns = <14>; + ti,cs-bus-width = <16>; + + flash@0,0x0000000 { + compatible = "cfi-flash"; + reg = <0 0x0000000 0x4000000>; + + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt new file mode 100644 index 000000000..63f674ffe --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -0,0 +1,84 @@ +* EMIF family of TI SDRAM controllers + +EMIF - External Memory Interface - is an SDRAM controller used in +TI SoCs. EMIF supports, based on the IP revision, one or more of +DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance +of the EMIF IP and memory parts attached to it. Certain revisions +of the EMIF controller also contain optional ECC support, which +corrects one bit errors and detects two bit errors. + +Required properties: +- compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> + is the IP revision of the specific EMIF instance. For newer controllers, + compatible should be one of the following: + "ti,emif-am3352" + "ti,emif-am4372" + "ti,emif-dra7xx" + "ti,emif-keystone" + +- phy-type : <u32> indicating the DDR phy type. Following are the + allowed values + <1> : Attila PHY + <2> : Intelli PHY + +- device-handle : phandle to a "lpddr2" node representing the memory part + +- ti,hwmods : For TI hwmods processing and omap device creation + the value shall be "emif<n>" where <n> is the number of the EMIF + instance with base 1. +- interrupts : interrupt used by the controller + +Required only for "ti,emif-am3352" and "ti,emif-am4372": +- sram : Phandles for generic sram driver nodes, + first should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.yaml + for more details. + +Optional properties: +- cs1-used : Have this property if CS1 of this EMIF + instance has a memory part attached to it. If there is a memory + part attached to CS1, it should be the same type as the one on CS0, + so there is no need to give the details of this memory part. + +- cal-resistor-per-cs : Have this property if the board has one + calibration resistor per chip-select. + +- hw-caps-read-idle-ctrl: Have this property if the controller + supports read idle window programming + +- hw-caps-dll-calib-ctrl: Have this property if the controller + supports dll calibration control + +- hw-caps-ll-interface : Have this property if the controller + has a low latency interface and corresponding interrupt events + +- hw-caps-temp-alert : Have this property if the controller + has capability for generating SDRAM temperature alerts + +-Examples: + +emif1: emif@4c000000 { + compatible = "ti,emif-4d"; + ti,hwmods = "emif2"; + phy-type = <1>; + device-handle = <&elpida_ECB240ABACN>; + cs1-used; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; +}; + +/* From am33xx.dtsi */ +emif: emif@4c000000 { + compatible = "ti,emif-am3352"; + reg = <0x4C000000 0x1000>; + sram = <&pm_sram_code + &pm_sram_data>; +}; + +emif1: emif@4c000000 { + compatible = "ti,emif-dra7xx"; + reg = <0x4c000000 0x200>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/xlnx,zynq-ddrc-a05.yaml b/Documentation/devicetree/bindings/memory-controllers/xlnx,zynq-ddrc-a05.yaml new file mode 100644 index 000000000..8f72e2f85 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/xlnx,zynq-ddrc-a05.yaml @@ -0,0 +1,38 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/xlnx,zynq-ddrc-a05.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Zynq A05 DDR Memory Controller + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Manish Narani <manish.narani@xilinx.com> + - Michal Simek <michal.simek@xilinx.com> + +description: + The Zynq DDR ECC controller has an optional ECC support in half-bus width + (16-bit) configuration. It is cappable of correcting single bit ECC errors + and detecting double bit ECC errors. + +properties: + compatible: + const: xlnx,zynq-ddrc-a05 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + memory-controller@f8006000 { + compatible = "xlnx,zynq-ddrc-a05"; + reg = <0xf8006000 0x1000>; + }; +... |