diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml | 188 |
1 files changed, 188 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml new file mode 100644 index 000000000..29339d019 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + +allOf: + - $ref: "mmc-controller.yaml" + +description: | + The Enhanced Secure Digital Host Controller on Freescale i.MX family + provides an interface for MMC, SD, and SDIO types of memory cards. + + This file documents differences between the core properties described + by mmc.txt and the properties used by the sdhci-esdhc-imx driver. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx25-esdhc + - fsl,imx35-esdhc + - fsl,imx51-esdhc + - fsl,imx53-esdhc + - fsl,imx6q-usdhc + - fsl,imx6sl-usdhc + - fsl,imx6sll-usdhc + - fsl,imx6sx-usdhc + - fsl,imx6ull-usdhc + - fsl,imx7d-usdhc + - fsl,imx7ulp-usdhc + - fsl,imx8mm-usdhc + - fsl,imxrt1050-usdhc + - nxp,s32g2-usdhc + - items: + - enum: + - fsl,imx8mq-usdhc + - const: fsl,imx7d-usdhc + - items: + - enum: + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - fsl,imx93-usdhc + - fsl,imx8ulp-usdhc + - const: fsl,imx8mm-usdhc + - items: + - enum: + - fsl,imx8qm-usdhc + - const: fsl,imx8qxp-usdhc + - items: + - enum: + - fsl,imx8dxl-usdhc + - fsl,imx8mm-usdhc + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - fsl,imx8qm-usdhc + - fsl,imx8qxp-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + - items: + - enum: + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - const: fsl,imx8mm-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + - items: + - enum: + - fsl,imx8qm-usdhc + - const: fsl,imx8qxp-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + fsl,wp-controller: + description: | + boolean, if present, indicate to use controller internal write protection. + type: boolean + + fsl,delay-line: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the number of delay cells for override mode. + This is used to set the clock delay for DLL(Delay Line) on override mode + to select a proper data sampling window in case the clock quality is not good + due to signal path is too long on the board. Please refer to eSDHC/uSDHC + chapter, DLL (Delay Line) section in RM for details. + default: 0 + + voltage-ranges: + $ref: '/schemas/types.yaml#/definitions/uint32-matrix' + description: | + Specify the voltage range in case there are software transparent level + shifters on the outputs of the controller. Two cells are required, first + cell specifies minimum slot voltage (mV), second cell specifies maximum + slot voltage (mV). + items: + items: + - description: value for minimum slot voltage + - description: value for maximum slot voltage + maxItems: 1 + + fsl,tuning-start-tap: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the start delay cell point when send first CMD19 in tuning procedure. + default: 0 + + fsl,tuning-step: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the increasing delay cell steps in tuning procedure. + The uSDHC use one delay cell as default increasing step to do tuning process. + This property allows user to change the tuning step to more than one delay + cells which is useful for some special boards or cards when the default + tuning step can't find the proper delay window within limited tuning retries. + default: 0 + + fsl,strobe-dll-delay-target: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the strobe dll control slave delay target. + This delay target programming host controller loopback read clock, and this + property allows user to change the delay target for the strobe input read clock. + If not use this property, driver default set the delay target to value 7. + Only eMMC HS400 mode need to take care of this property. + default: 0 + + clocks: + maxItems: 3 + description: + Handle clocks for the sdhc controller. + + clock-names: + items: + - const: ipg + - const: ahb + - const: per + + power-domains: + maxItems: 1 + + pinctrl-names: + oneOf: + - minItems: 3 + items: + - const: default + - const: state_100mhz + - const: state_200mhz + - const: sleep + - minItems: 1 + items: + - const: default + - const: sleep + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + mmc@70004000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70004000 0x4000>; + interrupts = <1>; + fsl,wp-controller; + }; + + mmc@70008000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70008000 0x4000>; + interrupts = <2>; + cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */ + }; |