diff options
Diffstat (limited to '')
66 files changed, 6288 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml new file mode 100644 index 000000000..02ecc9341 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/allwinner,sun4i-a10-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 MMC Controller + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + oneOf: + - const: allwinner,sun4i-a10-mmc + - const: allwinner,sun5i-a13-mmc + - const: allwinner,sun7i-a20-mmc + - const: allwinner,sun8i-a83t-emmc + - const: allwinner,sun9i-a80-mmc + - const: allwinner,sun20i-d1-mmc + - const: allwinner,sun50i-a64-emmc + - const: allwinner,sun50i-a64-mmc + - const: allwinner,sun50i-a100-emmc + - const: allwinner,sun50i-a100-mmc + - items: + - const: allwinner,sun8i-a83t-mmc + - const: allwinner,sun7i-a20-mmc + - items: + - const: allwinner,sun8i-r40-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun8i-r40-mmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun50i-h5-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun50i-h5-mmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun50i-h6-emmc + - const: allwinner,sun50i-a64-emmc + - items: + - const: allwinner,sun50i-h6-mmc + - const: allwinner,sun50i-a64-mmc + - items: + - const: allwinner,sun20i-d1-emmc + - const: allwinner,sun50i-a100-emmc + - items: + - const: allwinner,sun50i-h616-emmc + - const: allwinner,sun50i-a100-emmc + - items: + - const: allwinner,sun50i-h616-mmc + - const: allwinner,sun50i-a100-mmc + - items: + - const: allwinner,suniv-f1c100s-mmc + - const: allwinner,sun7i-a20-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + items: + - description: Bus Clock + - description: Module Clock + - description: Output Clock + - description: Sample Clock + + clock-names: + minItems: 2 + items: + - const: ahb + - const: mmc + - const: output + - const: sample + + resets: + maxItems: 1 + + reset-names: + const: ahb + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + mmc0: mmc@1c0f000 { + compatible = "allwinner,sun5i-a13-mmc"; + reg = <0x01c0f000 0x1000>; + clocks = <&ahb_gates 8>, <&mmc0_clk>; + clock-names = "ahb", "mmc"; + interrupts = <32>; + bus-width = <4>; + cd-gpios = <&pio 7 1 0>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt new file mode 100644 index 000000000..ccc5358db --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -0,0 +1,39 @@ +Amlogic SD / eMMC controller for S905/GXBB family SoCs + +The MMC 5.1 compliant host controller on Amlogic provides the +interface for SD, eMMC and SDIO devices. + +This file documents the properties in addition to those available in +the MMC core bindings, documented by mmc.txt. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gx-mmc" + - "amlogic,meson-gxbb-mmc" + - "amlogic,meson-gxl-mmc" + - "amlogic,meson-gxm-mmc" + - "amlogic,meson-axg-mmc" +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "core" - Main peripheral bus clock + "clkin0" - Parent clock of internal mux + "clkin1" - Other parent clock of internal mux + The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the + clock rate requested by the MMC core. +- resets : phandle of the internal reset line + +Optional properties: +- amlogic,dram-access-quirk: set when controller's internal DMA engine cannot access the + DRAM memory, like on the G12A dedicated SDIO controller. + +Example: + + sd_emmc_a: mmc@70000 { + compatible = "amlogic,meson-gxbb-mmc"; + reg = <0x0 0x70000 0x0 0x2000>; + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + pinctrl-0 = <&emmc_pins>; + resets = <&reset RESET_SD_EMMC_A>; + }; diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml new file mode 100644 index 000000000..1c391bec4 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/amlogic,meson-mx-sdhc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson SDHC controller + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +description: | + The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC + card interface with 1/4/8-bit bus width. + It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock). + +properties: + compatible: + items: + - enum: + - amlogic,meson8-sdhc + - amlogic,meson8b-sdhc + - amlogic,meson8m2-sdhc + - const: amlogic,meson-mx-sdhc + + reg: + minItems: 1 + + interrupts: + minItems: 1 + + clocks: + minItems: 5 + + clock-names: + items: + - const: clkin0 + - const: clkin1 + - const: clkin2 + - const: clkin3 + - const: pclk + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + sdhc: mmc@8e00 { + compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc"; + reg = <0x8e00 0x42>; + interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>; + clocks = <&xtal>, + <&fclk_div4>, + <&fclk_div3>, + <&fclk_div5>, + <&sdhc_pclk>; + clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk"; + }; diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt new file mode 100644 index 000000000..8765c605e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt @@ -0,0 +1,54 @@ +* Amlogic Meson6, Meson8 and Meson8b SDIO/MMC controller + +The highspeed MMC host controller on Amlogic SoCs provides an interface +for MMC, SD, SDIO and SDHC types of memory cards. + +Supported maximum speeds are the ones of the eMMC standard 4.41 as well +as the speed of SD standard 2.0. + +The hardware provides an internal "mux" which allows up to three slots +to be controlled. Only one slot can be accessed at a time. + +Required properties: + - compatible : must be one of + - "amlogic,meson8-sdio" + - "amlogic,meson8b-sdio" + along with the generic "amlogic,meson-mx-sdio" + - reg : mmc controller base registers + - interrupts : mmc controller interrupt + - #address-cells : must be 1 + - size-cells : must be 0 + - clocks : phandle to clock providers + - clock-names : must contain "core" and "clkin" + +Required child nodes: +A node for each slot provided by the MMC controller is required. +NOTE: due to a driver limitation currently only one slot (= child node) + is supported! + +Required properties on each child node (= slot): + - compatible : must be "mmc-slot" (see mmc.txt within this directory) + - reg : the slot (or "port") ID + +Optional properties on each child node (= slot): + - bus-width : must be 1 or 4 (8-bit bus is not supported) + - for cd and all other additional generic mmc parameters + please refer to mmc.txt within this directory + +Examples: + mmc@c1108c20 { + compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio"; + reg = <0xc1108c20 0x20>; + interrupts = <0 28 1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; + clock-names = "core", "clkin"; + + slot@1 { + compatible = "mmc-slot"; + reg = <1>; + + bus-width = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.yaml b/Documentation/devicetree/bindings/mmc/arasan,sdhci.yaml new file mode 100644 index 000000000..83be9e93d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.yaml @@ -0,0 +1,330 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mmc/arasan,sdhci.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Device Tree Bindings for the Arasan SDHCI Controller + +maintainers: + - Adrian Hunter <adrian.hunter@intel.com> + +allOf: + - $ref: "mmc-controller.yaml#" + - if: + properties: + compatible: + contains: + const: arasan,sdhci-5.1 + then: + required: + - phys + - phy-names + - if: + properties: + compatible: + contains: + enum: + - xlnx,zynqmp-8.9a + - xlnx,versal-8.9a + then: + properties: + clock-output-names: + oneOf: + - items: + - const: clk_out_sd0 + - const: clk_in_sd0 + - items: + - const: clk_out_sd1 + - const: clk_in_sd1 + +properties: + compatible: + oneOf: + - const: arasan,sdhci-8.9a # generic Arasan SDHCI 8.9a PHY + - const: arasan,sdhci-4.9a # generic Arasan SDHCI 4.9a PHY + - const: arasan,sdhci-5.1 # generic Arasan SDHCI 5.1 PHY + - items: + - const: rockchip,rk3399-sdhci-5.1 # rk3399 eMMC PHY + - const: arasan,sdhci-5.1 + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - items: + - const: xlnx,zynqmp-8.9a # ZynqMP SDHCI 8.9a PHY + - const: arasan,sdhci-8.9a + description: + For this device it is strongly suggested to include + clock-output-names and '#clock-cells'. + - items: + - const: xlnx,versal-8.9a # Versal SDHCI 8.9a PHY + - const: arasan,sdhci-8.9a + description: + For this device it is strongly suggested to include + clock-output-names and '#clock-cells'. + - items: + - const: intel,lgm-sdhci-5.1-emmc # Intel LGM eMMC PHY + - const: arasan,sdhci-5.1 + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - items: + - const: intel,lgm-sdhci-5.1-sdxc # Intel LGM SDXC PHY + - const: arasan,sdhci-5.1 + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - items: + - const: intel,keembay-sdhci-5.1-emmc # Intel Keem Bay eMMC PHY + - const: arasan,sdhci-5.1 + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - const: intel,keembay-sdhci-5.1-sd # Intel Keem Bay SD controller + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - const: intel,keembay-sdhci-5.1-sdio # Intel Keem Bay SDIO controller + description: + For this device it is strongly suggested to include + arasan,soc-ctl-syscon. + - items: + - const: intel,thunderbay-sdhci-5.1 # Intel Thunder Bay eMMC PHY + - const: arasan,sdhci-5.1 + description: + For this device it is strongly suggested to include + clock-output-names and '#clock-cells'. + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: + minItems: 2 + items: + - const: clk_xin + - const: clk_ahb + - const: gate + + interrupts: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: phy_arasan + + resets: + maxItems: 1 + + arasan,soc-ctl-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + A phandle to a syscon device (see ../mfd/syscon.txt) used to access + core corecfg registers. Offsets of registers in this syscon are + determined based on the main compatible string for the device. + + clock-output-names: + minItems: 1 + maxItems: 2 + description: + Name of the card clock which will be exposed by this device. + + '#clock-cells': + enum: [0, 1] + description: + With this property in place we will export one or two clocks + representing the Card Clock. These clocks are expected to be + consumed by our PHY. + + xlnx,fails-without-test-cd: + $ref: /schemas/types.yaml#/definitions/flag + description: + When present, the controller doesn't work when the CD line is not + connected properly, and the line is not connected properly. + Test mode can be used to force the controller to function. + + xlnx,int-clock-stable-broken: + $ref: /schemas/types.yaml#/definitions/flag + description: + When present, the controller always reports that the internal clock + is stable even when it is not. + + xlnx,mio-bank: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + description: + The MIO bank number in which the command and data lines are configured. + +dependencies: + '#clock-cells': [ clock-output-names ] + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + mmc@e0100000 { + compatible = "arasan,sdhci-8.9a"; + reg = <0xe0100000 0x1000>; + clock-names = "clk_xin", "clk_ahb"; + clocks = <&clkc 21>, <&clkc 32>; + interrupt-parent = <&gic>; + interrupts = <0 24 4>; + }; + + - | + mmc@e2800000 { + compatible = "arasan,sdhci-5.1"; + reg = <0xe2800000 0x1000>; + clock-names = "clk_xin", "clk_ahb"; + clocks = <&cru 8>, <&cru 18>; + interrupt-parent = <&gic>; + interrupts = <0 24 4>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + }; + + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + mmc@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0xfe330000 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + arasan,soc-ctl-syscon = <&grf>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clock-output-names = "emmc_cardclock"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + #clock-cells = <0>; + }; + + - | + mmc@ff160000 { + compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; + interrupt-parent = <&gic>; + interrupts = <0 48 4>; + reg = <0xff160000 0x1000>; + clocks = <&clk200>, <&clk200>; + clock-names = "clk_xin", "clk_ahb"; + clock-output-names = "clk_out_sd0", "clk_in_sd0"; + #clock-cells = <1>; + clk-phase-sd-hs = <63>, <72>; + }; + + - | + mmc@f1040000 { + compatible = "xlnx,versal-8.9a", "arasan,sdhci-8.9a"; + interrupt-parent = <&gic>; + interrupts = <0 126 4>; + reg = <0xf1040000 0x10000>; + clocks = <&clk200>, <&clk200>; + clock-names = "clk_xin", "clk_ahb"; + clock-output-names = "clk_out_sd0", "clk_in_sd0"; + #clock-cells = <1>; + clk-phase-sd-hs = <132>, <60>; + }; + + - | + #define LGM_CLK_EMMC5 + #define LGM_CLK_NGI + #define LGM_GCLK_EMMC + mmc@ec700000 { + compatible = "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1"; + reg = <0xec700000 0x300>; + interrupt-parent = <&ioapic1>; + interrupts = <44 1>; + clocks = <&cgu0 LGM_CLK_EMMC5>, <&cgu0 LGM_CLK_NGI>, + <&cgu0 LGM_GCLK_EMMC>; + clock-names = "clk_xin", "clk_ahb", "gate"; + clock-output-names = "emmc_cardclock"; + #clock-cells = <0>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + arasan,soc-ctl-syscon = <&sysconf>; + }; + + - | + #define LGM_CLK_SDIO + #define LGM_GCLK_SDXC + mmc@ec600000 { + compatible = "intel,lgm-sdhci-5.1-sdxc", "arasan,sdhci-5.1"; + reg = <0xec600000 0x300>; + interrupt-parent = <&ioapic1>; + interrupts = <43 1>; + clocks = <&cgu0 LGM_CLK_SDIO>, <&cgu0 LGM_CLK_NGI>, + <&cgu0 LGM_GCLK_SDXC>; + clock-names = "clk_xin", "clk_ahb", "gate"; + clock-output-names = "sdxc_cardclock"; + #clock-cells = <0>; + phys = <&sdxc_phy>; + phy-names = "phy_arasan"; + arasan,soc-ctl-syscon = <&sysconf>; + }; + + - | + #define KEEM_BAY_PSS_AUX_EMMC + #define KEEM_BAY_PSS_EMMC + mmc@33000000 { + compatible = "intel,keembay-sdhci-5.1-emmc", "arasan,sdhci-5.1"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x33000000 0x300>; + clock-names = "clk_xin", "clk_ahb"; + clocks = <&scmi_clk KEEM_BAY_PSS_AUX_EMMC>, + <&scmi_clk KEEM_BAY_PSS_EMMC>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + assigned-clocks = <&scmi_clk KEEM_BAY_PSS_AUX_EMMC>; + assigned-clock-rates = <200000000>; + clock-output-names = "emmc_cardclock"; + #clock-cells = <0>; + arasan,soc-ctl-syscon = <&mmc_phy_syscon>; + }; + + - | + #define KEEM_BAY_PSS_AUX_SD0 + #define KEEM_BAY_PSS_SD0 + mmc@31000000 { + compatible = "intel,keembay-sdhci-5.1-sd"; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x31000000 0x300>; + clock-names = "clk_xin", "clk_ahb"; + clocks = <&scmi_clk KEEM_BAY_PSS_AUX_SD0>, + <&scmi_clk KEEM_BAY_PSS_SD0>; + arasan,soc-ctl-syscon = <&sd0_phy_syscon>; + }; + + - | + #define EMMC_XIN_CLK + #define EMMC_AXI_CLK + #define TBH_PSS_EMMC_RST_N + mmc@80420000 { + compatible = "intel,thunderbay-sdhci-5.1", "arasan,sdhci-5.1"; + interrupts = <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x80420000 0x400>; + clocks = <&scmi_clk EMMC_XIN_CLK>, + <&scmi_clk EMMC_AXI_CLK>; + clock-names = "clk_xin", "clk_ahb"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + assigned-clocks = <&scmi_clk EMMC_XIN_CLK>; + clock-output-names = "emmc_cardclock"; + resets = <&rst_pss1 TBH_PSS_EMMC_RST_N>; + #clock-cells = <0x0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml new file mode 100644 index 000000000..1e69a5a42 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml @@ -0,0 +1,244 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PrimeCell MultiMedia Card Interface (MMCI) PL180 and PL181 + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Ulf Hansson <ulf.hansson@linaro.org> + +description: + The ARM PrimeCells MMCI PL180 and PL181 provides an interface for + reading and writing to MultiMedia and SD cards alike. Over the years + vendors have use the VHDL code from ARM to create derivative MMC/SD/SDIO + host controllers with very similar characteristics. + +allOf: + - $ref: /schemas/arm/primecell.yaml# + - $ref: mmc-controller.yaml# + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + enum: + - arm,pl180 + - arm,pl181 + - arm,pl18x + required: + - compatible + +properties: + compatible: + oneOf: + - description: The first version of the block, simply called + PL180 and found in the ARM Integrator IM/PD1 logic module. + items: + - const: arm,pl180 + - const: arm,primecell + - description: The improved version of the block, found in the + ARM Versatile and later reference designs. Further revisions + exist but get detected at runtime by reading some magic numbers + in the PrimeCell ID registers. + items: + - const: arm,pl181 + - const: arm,primecell + - description: Wildcard entry that will let the operating system + inspect the PrimeCell ID registers to determine which hardware + variant of PL180 or PL181 this is. + items: + - const: arm,pl18x + - const: arm,primecell + - description: Entry for STMicroelectronics variant of PL18x. + This dedicated compatible is used by bootloaders. + items: + - const: st,stm32-sdmmc2 + - const: arm,pl18x + - const: arm,primecell + + clocks: + description: One or two clocks, the "apb_pclk" and the "MCLK" + which is the core block clock. The names are not compulsory. + minItems: 1 + maxItems: 2 + + dmas: + maxItems: 2 + + dma-names: + oneOf: + - items: + - const: tx + - const: rx + - items: + - const: rx + - const: tx + + power-domains: true + + resets: + maxItems: 1 + + reg: + description: the MMIO memory window must be exactly 4KB (0x1000) and the + layout should provide the PrimeCell ID registers so that the device can + be discovered. On ST Micro variants, a second register window may be + defined if a delay block is present and used for tuning. + + interrupts: + description: The first interrupt is the command interrupt and corresponds + to the event at the end of a command. The second interrupt is the + PIO (polled I/O) interrupt and occurs when the FIFO needs to be + emptied as part of a bulk read from the card. Some variants have these + two interrupts wired into the same line (logic OR) and in that case + only one interrupt may be provided. + minItems: 1 + maxItems: 2 + + st,sig-dir-dat0: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[0]. + + st,sig-dir-dat2: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[2]. + + st,sig-dir-dat31: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[3] and DAT[1]. + + st,sig-dir-dat74: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[7] and DAT[4]. + + st,sig-dir-cmd: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, CMD signal direction used for + pin CMD. + + st,sig-pin-fbclk: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, feedback clock FBCLK signal pin + in use. + + st,sig-dir: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, signal direction polarity used for + pins CMD, DAT[0], DAT[1], DAT[2] and DAT[3]. + + st,neg-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, data and command phase relation, + generated on the sd clock falling edge. + + st,use-ckin: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, use CKIN pin from an external + driver to sample the receive data (for example with a voltage switch + transceiver). + + st,cmd-gpios: + maxItems: 1 + description: + The GPIO matching the CMD pin. + + st,ck-gpios: + maxItems: 1 + description: + The GPIO matching the CK pin. + + st,ckin-gpios: + maxItems: 1 + description: + The GPIO matching the CKIN pin. + +dependencies: + st,cmd-gpios: [ "st,use-ckin" ] + st,ck-gpios: [ "st,use-ckin" ] + st,ckin-gpios: [ "st,use-ckin" ] + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + mmc@5000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x5000 0x1000>; + interrupts-extended = <&vic 22 &sic 1>; + clocks = <&xtal24mhz>, <&pclk>; + clock-names = "mclk", "apb_pclk"; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dma 29 0 0x2>, <&dma 29 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + }; + + - | + mmc@101f6000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x101f6000 0x1000>; + clocks = <&sdiclk>, <&pclksdi>; + clock-names = "mclk", "apb_pclk"; + interrupts = <22>; + max-frequency = <400000>; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + full-pwr-cycle; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-dir-cmd; + st,sig-pin-fbclk; + vmmc-supply = <&vmmc_regulator>; + }; + + - | + mmc@52007000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x52007000 0x1000>; + interrupts = <49>; + clocks = <&rcc 0>; + clock-names = "apb_pclk"; + resets = <&rcc 1>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml new file mode 100644 index 000000000..987b287f3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# Copyright 2019 IBM Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED SD/SDIO/MMC Controller + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + - Ryan Chen <ryanchen.aspeed@gmail.com> + +description: |+ + The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO + Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if + only a single slot is enabled. + + The two slots are supported by a common configuration area. As the SDHCIs for + the slots are dependent on the common configuration area, they are described + as child nodes. + +properties: + compatible: + enum: + - aspeed,ast2400-sd-controller + - aspeed,ast2500-sd-controller + - aspeed,ast2600-sd-controller + reg: + maxItems: 1 + description: Common configuration registers + "#address-cells": + const: 1 + "#size-cells": + const: 1 + ranges: true + clocks: + maxItems: 1 + description: The SD/SDIO controller clock gate + +patternProperties: + "^sdhci@[0-9a-f]+$": + type: object + $ref: mmc-controller.yaml + + properties: + compatible: + enum: + - aspeed,ast2400-sdhci + - aspeed,ast2500-sdhci + - aspeed,ast2600-sdhci + reg: + maxItems: 1 + description: The SDHCI registers + clocks: + maxItems: 1 + description: The SD bus clock + interrupts: + maxItems: 1 + description: The SD interrupt shared between both slots + sdhci,auto-cmd12: + type: boolean + description: Specifies that controller should use auto CMD12 + required: + - compatible + - reg + - clocks + - interrupts + +additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - clocks + +examples: + - | + #include <dt-bindings/clock/aspeed-clock.h> + sdc@1e740000 { + compatible = "aspeed,ast2500-sd-controller"; + reg = <0x1e740000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1e740000 0x20000>; + clocks = <&syscon ASPEED_CLK_GATE_SDCLK>; + + sdhci0: sdhci@100 { + compatible = "aspeed,ast2500-sdhci"; + reg = <0x100 0x100>; + interrupts = <26>; + sdhci,auto-cmd12; + clocks = <&syscon ASPEED_CLK_SDIO>; + }; + + sdhci1: sdhci@200 { + compatible = "aspeed,ast2500-sdhci"; + reg = <0x200 0x100>; + interrupts = <26>; + sdhci,auto-cmd12; + clocks = <&syscon ASPEED_CLK_SDIO>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt new file mode 100644 index 000000000..07ad02075 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -0,0 +1,73 @@ +* Atmel High Speed MultiMedia Card Interface + +This controller on atmel products provides an interface for MMC, SD and SDIO +types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the atmel-mci driver. + +1) MCI node + +Required properties: +- compatible: should be "atmel,hsmci" +- #address-cells: should be one. The cell is the slot id. +- #size-cells: should be zero. +- at least one slot node +- clock-names: tuple listing input clock names. + Required elements: "mci_clk" +- clocks: phandles to input clocks. + +The node contains child nodes for each slot that the platform uses + +Example MCI node: + +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "mci_clk"; + clocks = <&mci0_clk>; + + [ child node definitions...] +}; + +2) slot nodes + +Required properties: +- reg: should contain the slot id. +- bus-width: number of data lines connected to the controller + +Optional properties: +- cd-gpios: specify GPIOs for card detection +- cd-inverted: invert the value of external card detect gpio line +- wp-gpios: specify GPIOs for write protection + +Example slot node: + +slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; +}; + +Example full MCI node: +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; + }; + slot@1 { + reg = <1>; + bus-width = <4>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt new file mode 100644 index 000000000..b0f0999ea --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt @@ -0,0 +1,29 @@ +* Mellanox Bluefield SoC specific extensions to the Synopsys Designware + Mobile Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC +specific extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be one of the following. + - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC + specific extensions. + +Example: + + /* Mellanox Bluefield SoC MMC */ + mmc@6008000 { + compatible = "mellanox,bluefield-dw-mshc"; + reg = <0x6008000 0x400>; + interrupts = <32>; + fifo-depth = <0x100>; + clock-frequency = <24000000>; + bus-width = <8>; + cap-mmc-highspeed; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhost.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhost.txt new file mode 100644 index 000000000..d876580ae --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhost.txt @@ -0,0 +1,23 @@ +Broadcom BCM2835 SDHOST controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the BCM2835 controller. + +Required properties: +- compatible: Should be "brcm,bcm2835-sdhost". +- clocks: The clock feeding the SDHOST controller. + +Optional properties: +- dmas: DMA channel for read and write. + See Documentation/devicetree/bindings/dma/dma.txt for details + +Example: + +sdhost: mmc@7e202000 { + compatible = "brcm,bcm2835-sdhost"; + reg = <0x7e202000 0x100>; + interrupts = <2 24>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + dmas = <&dma 13>; + dma-names = "rx-tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml b/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml new file mode 100644 index 000000000..2f63f2cde --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/brcm,iproc-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom IPROC SDHCI controller + +maintainers: + - Ray Jui <ray.jui@broadcom.com> + - Scott Branden <scott.branden@broadcom.com> + - Nicolas Saenz Julienne <nsaenz@kernel.org> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + enum: + - brcm,bcm2835-sdhci + - brcm,bcm2711-emmc2 + - brcm,sdhci-iproc-cygnus + - brcm,sdhci-iproc + - brcm,bcm7211a0-sdhci + + reg: + minItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: + Handle to core clock for the sdhci controller. + + sdhci,auto-cmd12: + type: boolean + description: Specifies that controller should use auto CMD12 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/bcm-cygnus.h> + + mmc@18041000 { + compatible = "brcm,sdhci-iproc-cygnus"; + reg = <0x18041000 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lcpll0_clks BCM_CYGNUS_LCPLL0_SDIO_CLK>; + bus-width = <4>; + sdhci,auto-cmd12; + no-1-8-v; + }; +... diff --git a/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt new file mode 100644 index 000000000..7f5dd83f5 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt @@ -0,0 +1,21 @@ +Broadcom BCM281xx SDHCI + +This file documents differences between the core properties in mmc.txt +and the properties present in the bcm281xx SDHCI + +Required properties: +- compatible : Should be "brcm,kona-sdhci" +- DEPRECATED: compatible : Should be "bcm,kona-sdhci" +- clocks: phandle + clock specifier pair of the external clock + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + +sdio2: sdio@3f1a0000 { + compatible = "brcm,kona-sdhci"; + reg = <0x3f1a0000 0x10000>; + clocks = <&sdio3_clk>; + interrupts = <0x0 74 0x4>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml new file mode 100644 index 000000000..dead421e1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/brcm,sdhci-brcmstb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BRCMSTB/BMIPS SDHCI Controller binding + +maintainers: + - Al Cooper <alcooperx@gmail.com> + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm7216-sdhci + - const: brcm,bcm7445-sdhci + - const: brcm,sdhci-brcmstb + - items: + - enum: + - brcm,bcm7445-sdhci + - const: brcm,sdhci-brcmstb + - items: + - enum: + - brcm,bcm7425-sdhci + - const: brcm,sdhci-brcmstb + + reg: + maxItems: 2 + + reg-names: + items: + - const: host + - const: cfg + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: handle to core clock for the sdhci controller + - description: handle to improved 150Mhz clock for sdhci controller (Optional clock) + + clock-names: + minItems: 1 + items: + - const: sw_sdio + - const: sdio_freq # Optional clock + + clock-frequency: + description: + Maximum operating frequency of sdio_freq sdhci controller clock + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 100000000 + maximum: 150000000 + + sdhci,auto-cmd12: + type: boolean + description: Specifies that controller should use auto CMD12 + +allOf: + - $ref: mmc-controller.yaml# + - if: + properties: + clock-names: + contains: + const: sdio_freq + + then: + required: + - clock-frequency + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + mmc@84b0000 { + compatible = "brcm,bcm7216-sdhci", + "brcm,bcm7445-sdhci", + "brcm,sdhci-brcmstb"; + reg = <0x84b0000 0x260>, <0x84b0300 0x200>; + reg-names = "host", "cfg"; + sd-uhs-sdr50; + sd-uhs-ddr50; + sd-uhs-sdr104; + sdhci,auto-cmd12; + interrupts = <0x0 0x26 0x4>; + clocks = <&scmi_clk 245>; + clock-names = "sw_sdio"; + }; + + mmc@84b1000 { + compatible = "brcm,bcm7216-sdhci", + "brcm,bcm7445-sdhci", + "brcm,sdhci-brcmstb"; + reg = <0x84b1000 0x260>, <0x84b1300 0x200>; + reg-names = "host", "cfg"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + supports-cqe; + non-removable; + bus-width = <0x8>; + interrupts = <0x0 0x27 0x4>; + clocks = <&scmi_clk 245>; + clock-names = "sw_sdio"; + }; diff --git a/Documentation/devicetree/bindings/mmc/cavium-mmc.txt b/Documentation/devicetree/bindings/mmc/cavium-mmc.txt new file mode 100644 index 000000000..1433e6201 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/cavium-mmc.txt @@ -0,0 +1,57 @@ +* Cavium Octeon & ThunderX MMC controller + +The highspeed MMC host controller on Caviums SoCs provides an interface +for MMC and SD types of memory cards. + +Supported maximum speeds are the ones of the eMMC standard 4.41 as well +as the speed of SD standard 4.0. Only 3.3 Volt is supported. + +Required properties: + - compatible : should be one of: + cavium,octeon-6130-mmc + cavium,octeon-7890-mmc + cavium,thunder-8190-mmc + cavium,thunder-8390-mmc + mmc-slot + - reg : mmc controller base registers + - clocks : phandle + +Optional properties: + - for cd, bus-width and additional generic mmc parameters + please refer to mmc.txt within this directory + - cavium,cmd-clk-skew : number of coprocessor clocks before sampling command + - cavium,dat-clk-skew : number of coprocessor clocks before sampling data + +Deprecated properties: +- spi-max-frequency : use max-frequency instead +- cavium,bus-max-width : use bus-width instead +- power-gpios : use vmmc-supply instead +- cavium,octeon-6130-mmc-slot : use mmc-slot instead + +Examples: + mmc_1_4: mmc@1,4 { + compatible = "cavium,thunder-8390-mmc"; + reg = <0x0c00 0 0 0 0>; /* DEVFN = 0x0c (1:4) */ + #address-cells = <1>; + #size-cells = <0>; + clocks = <&sclk>; + + mmc-slot@0 { + compatible = "mmc-slot"; + reg = <0>; + vmmc-supply = <&mmc_supply_3v3>; + max-frequency = <42000000>; + bus-width = <4>; + cap-sd-highspeed; + }; + + mmc-slot@1 { + compatible = "mmc-slot"; + reg = <1>; + vmmc-supply = <&mmc_supply_3v3>; + max-frequency = <42000000>; + bus-width = <8>; + cap-mmc-highspeed; + non-removable; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml b/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml new file mode 100644 index 000000000..8b1a0fdcb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/cdns,sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence SD/SDIO/eMMC Host Controller (SD4HC) + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +allOf: + - $ref: mmc-controller.yaml + +properties: + compatible: + items: + - enum: + - microchip,mpfs-sd4hc + - socionext,uniphier-sd4hc + - const: cdns,sd4hc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + # PHY DLL input delays: + # They are used to delay the data valid window, and align the window to + # sampling clock. The delay starts from 5ns (for delay parameter equal to 0) + # and it is increased by 2.5ns in each step. + + cdns,phy-input-delay-sd-highspeed: + description: Value of the delay in the input path for SD high-speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-legacy: + description: Value of the delay in the input path for legacy timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-sd-uhs-sdr12: + description: Value of the delay in the input path for SD UHS SDR12 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-sd-uhs-sdr25: + description: Value of the delay in the input path for SD UHS SDR25 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-sd-uhs-sdr50: + description: Value of the delay in the input path for SD UHS SDR50 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-sd-uhs-ddr50: + description: Value of the delay in the input path for SD UHS DDR50 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-mmc-highspeed: + description: Value of the delay in the input path for MMC high-speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-input-delay-mmc-ddr: + description: Value of the delay in the input path for eMMC high-speed DDR timing + + # PHY DLL clock delays: + # Each delay property represents the fraction of the clock period. + # The approximate delay value will be + # (<delay property value>/128)*sdmclk_clock_period. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + cdns,phy-dll-delay-sdclk: + description: | + Value of the delay introduced on the sdclk output for all modes except + HS200, HS400 and HS400_ES. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x7f + + cdns,phy-dll-delay-sdclk-hsmmc: + description: | + Value of the delay introduced on the sdclk output for HS200, HS400 and + HS400_ES speed modes. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x7f + + cdns,phy-dll-delay-strobe: + description: | + Value of the delay introduced on the dat_strobe input used in + HS400 / HS400_ES speed modes. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x7f + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + emmc: mmc@5a000000 { + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; + reg = <0x5a000000 0x400>; + interrupts = <0 78 4>; + clocks = <&clk 4>; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + cdns,phy-dll-delay-sdclk = <0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt new file mode 100644 index 000000000..516fb0143 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt @@ -0,0 +1,32 @@ +* TI Highspeed MMC host controller for DaVinci + +The Highspeed MMC Host Controller on TI DaVinci family +provides an interface for MMC, SD and SDIO types of memory cards. + +This file documents the properties used by the davinci_mmc driver. + +Required properties: +- compatible: + Should be "ti,da830-mmc": for da830, da850, dm365 + Should be "ti,dm355-mmc": for dm355, dm644x + +Optional properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8>, default <1> +- max-frequency: Maximum operating clock frequency, default 25MHz. +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required. +- dma-names: RX and TX DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. + +Example: +mmc0: mmc@1c40000 { + compatible = "ti,da830-mmc", + reg = <0x40000 0x1000>; + interrupts = <16>; + bus-width = <4>; + max-frequency = <50000000>; + dmas = <&edma 16 + &edma 17>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt new file mode 100644 index 000000000..edb8cadb9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -0,0 +1,52 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) + +The Enhanced Secure Digital Host Controller provides an interface +for MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-esdhc driver. + +Required properties: + - compatible : should be "fsl,esdhc", or "fsl,<chip>-esdhc". + Possible compatibles for PowerPC: + "fsl,mpc8536-esdhc" + "fsl,mpc8378-esdhc" + "fsl,p2020-esdhc" + "fsl,p4080-esdhc" + "fsl,t1040-esdhc" + "fsl,t4240-esdhc" + Possible compatibles for ARM: + "fsl,ls1012a-esdhc" + "fsl,ls1028a-esdhc" + "fsl,ls1088a-esdhc" + "fsl,ls1043a-esdhc" + "fsl,ls1046a-esdhc" + "fsl,ls2080a-esdhc" + - clock-frequency : specifies eSDHC base clock frequency. + +Optional properties: + - sdhci,wp-inverted : specifies that eSDHC controller reports + inverted write-protect state; New devices should use the generic + "wp-inverted" property. + - sdhci,1-bit-only : specifies that a controller can only handle + 1-bit data transfers. New devices should use the generic + "bus-width = <1>" property. + - sdhci,auto-cmd12: specifies that a controller can only handle auto + CMD12. + - voltage-ranges : two cells are required, first cell specifies minimum + slot voltage (mV), second cell specifies maximum slot voltage (mV). + Several ranges could be specified. + - little-endian : If the host controller is little-endian mode, specify + this property. The default endian mode is big-endian. + +Example: + +sdhci@2e000 { + compatible = "fsl,mpc8378-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <42 0x8>; + interrupt-parent = <&ipic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; + voltage-ranges = <3300 3300>; +}; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml new file mode 100644 index 000000000..29339d019 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + +allOf: + - $ref: "mmc-controller.yaml" + +description: | + The Enhanced Secure Digital Host Controller on Freescale i.MX family + provides an interface for MMC, SD, and SDIO types of memory cards. + + This file documents differences between the core properties described + by mmc.txt and the properties used by the sdhci-esdhc-imx driver. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx25-esdhc + - fsl,imx35-esdhc + - fsl,imx51-esdhc + - fsl,imx53-esdhc + - fsl,imx6q-usdhc + - fsl,imx6sl-usdhc + - fsl,imx6sll-usdhc + - fsl,imx6sx-usdhc + - fsl,imx6ull-usdhc + - fsl,imx7d-usdhc + - fsl,imx7ulp-usdhc + - fsl,imx8mm-usdhc + - fsl,imxrt1050-usdhc + - nxp,s32g2-usdhc + - items: + - enum: + - fsl,imx8mq-usdhc + - const: fsl,imx7d-usdhc + - items: + - enum: + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - fsl,imx93-usdhc + - fsl,imx8ulp-usdhc + - const: fsl,imx8mm-usdhc + - items: + - enum: + - fsl,imx8qm-usdhc + - const: fsl,imx8qxp-usdhc + - items: + - enum: + - fsl,imx8dxl-usdhc + - fsl,imx8mm-usdhc + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - fsl,imx8qm-usdhc + - fsl,imx8qxp-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + - items: + - enum: + - fsl,imx8mn-usdhc + - fsl,imx8mp-usdhc + - const: fsl,imx8mm-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + - items: + - enum: + - fsl,imx8qm-usdhc + - const: fsl,imx8qxp-usdhc + - const: fsl,imx7d-usdhc + deprecated: true + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + fsl,wp-controller: + description: | + boolean, if present, indicate to use controller internal write protection. + type: boolean + + fsl,delay-line: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the number of delay cells for override mode. + This is used to set the clock delay for DLL(Delay Line) on override mode + to select a proper data sampling window in case the clock quality is not good + due to signal path is too long on the board. Please refer to eSDHC/uSDHC + chapter, DLL (Delay Line) section in RM for details. + default: 0 + + voltage-ranges: + $ref: '/schemas/types.yaml#/definitions/uint32-matrix' + description: | + Specify the voltage range in case there are software transparent level + shifters on the outputs of the controller. Two cells are required, first + cell specifies minimum slot voltage (mV), second cell specifies maximum + slot voltage (mV). + items: + items: + - description: value for minimum slot voltage + - description: value for maximum slot voltage + maxItems: 1 + + fsl,tuning-start-tap: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the start delay cell point when send first CMD19 in tuning procedure. + default: 0 + + fsl,tuning-step: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the increasing delay cell steps in tuning procedure. + The uSDHC use one delay cell as default increasing step to do tuning process. + This property allows user to change the tuning step to more than one delay + cells which is useful for some special boards or cards when the default + tuning step can't find the proper delay window within limited tuning retries. + default: 0 + + fsl,strobe-dll-delay-target: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specify the strobe dll control slave delay target. + This delay target programming host controller loopback read clock, and this + property allows user to change the delay target for the strobe input read clock. + If not use this property, driver default set the delay target to value 7. + Only eMMC HS400 mode need to take care of this property. + default: 0 + + clocks: + maxItems: 3 + description: + Handle clocks for the sdhc controller. + + clock-names: + items: + - const: ipg + - const: ahb + - const: per + + power-domains: + maxItems: 1 + + pinctrl-names: + oneOf: + - minItems: 3 + items: + - const: default + - const: state_100mhz + - const: state_200mhz + - const: sleep + - minItems: 1 + items: + - const: default + - const: sleep + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + mmc@70004000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70004000 0x4000>; + interrupts = <1>; + fsl,wp-controller; + }; + + mmc@70008000 { + compatible = "fsl,imx51-esdhc"; + reg = <0x70008000 0x4000>; + interrupts = <2>; + cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */ + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.yaml b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.yaml new file mode 100644 index 000000000..ffa162722 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/fsl-imx-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Secure Digital Host Controller for i.MX2/3 series + +maintainers: + - Markus Pargmann <mpa@pengutronix.de> + +allOf: + - $ref: "mmc-controller.yaml" + +properties: + compatible: + oneOf: + - const: fsl,imx21-mmc + - const: fsl,imx31-mmc + - items: + - const: fsl,imx27-mmc + - const: fsl,imx21-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + mmc@10014000 { + compatible = "fsl,imx27-mmc", "fsl,imx21-mmc"; + reg = <0x10014000 0x1000>; + interrupts = <11>; + dmas = <&dma 7>; + dma-names = "rx-tx"; + bus-width = <4>; + cd-gpios = <&gpio3 29>; + }; diff --git a/Documentation/devicetree/bindings/mmc/hi3798cv200-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/hi3798cv200-dw-mshc.txt new file mode 100644 index 000000000..a0693b714 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/hi3798cv200-dw-mshc.txt @@ -0,0 +1,40 @@ +* Hisilicon Hi3798CV200 specific extensions to the Synopsys Designware Mobile + Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Hisilicon Hi3798CV200 +specific extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: +- compatible: Should contain "hisilicon,hi3798cv200-dw-mshc". +- clocks: A list of phandle + clock-specifier pairs for the clocks listed + in clock-names. +- clock-names: Should contain the following: + "ciu" - The ciu clock described in synopsys-dw-mshc.txt. + "biu" - The biu clock described in synopsys-dw-mshc.txt. + "ciu-sample" - Hi3798CV200 extended phase clock for ciu sampling. + "ciu-drive" - Hi3798CV200 extended phase clock for ciu driving. + +Example: + + emmc: mmc@9830000 { + compatible = "hisilicon,hi3798cv200-dw-mshc"; + reg = <0x9830000 0x10000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_MMC_CIU_CLK>, + <&crg HISTB_MMC_BIU_CLK>, + <&crg HISTB_MMC_SAMPLE_CLK>, + <&crg HISTB_MMC_DRV_CLK>; + clock-names = "ciu", "biu", "ciu-sample", "ciu-drive"; + fifo-depth = <256>; + clock-frequency = <200000000>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + bus-width = <8>; + }; diff --git a/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml b/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml new file mode 100644 index 000000000..2d10aedf2 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/ingenic,mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs MMC Controller DT bindings + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - ingenic,jz4740-mmc + - ingenic,jz4725b-mmc + - ingenic,jz4760-mmc + - ingenic,jz4775-mmc + - ingenic,jz4780-mmc + - ingenic,x1000-mmc + - items: + - const: ingenic,jz4770-mmc + - const: ingenic,jz4760-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: mmc + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + oneOf: + - items: + - const: rx + - const: tx + - const: tx-rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/ingenic,jz4780-cgu.h> + #include <dt-bindings/dma/jz4780-dma.h> + mmc0: mmc@13450000 { + compatible = "ingenic,jz4780-mmc"; + reg = <0x13450000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <37>; + + clocks = <&cgu JZ4780_CLK_MSC0>; + clock-names = "mmc"; + + cap-sd-highspeed; + cap-mmc-highspeed; + cap-sdio-irq; + dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, + <&dma JZ4780_DMA_MSC0_TX 0xffffffff>; + dma-names = "rx", "tx"; + }; + - | + #include <dt-bindings/clock/ingenic,jz4780-cgu.h> + #include <dt-bindings/dma/jz4780-dma.h> + /* + * Alternative version of the example above, + * but using one single DMA channel for both + * TX and RX. + */ + mmc1: mmc@13460000 { + compatible = "ingenic,jz4780-mmc"; + reg = <0x13460000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <36>; + + clocks = <&cgu JZ4780_CLK_MSC1>; + clock-names = "mmc"; + + cap-sd-highspeed; + cap-mmc-highspeed; + cap-sdio-irq; + dmas = <&dma JZ4780_DMA_MSC1_TX JZ4780_DMA_MSC1_RX 0xffffffff>; + dma-names = "tx-rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt new file mode 100644 index 000000000..36c4bea67 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -0,0 +1,73 @@ +* Hisilicon specific extensions to the Synopsys Designware Mobile + Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Hisilicon specific +extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be one of the following. + - "hisilicon,hi3660-dw-mshc": for controllers with hi3660 specific extensions. + - "hisilicon,hi3670-dw-mshc", "hisilicon,hi3660-dw-mshc": for controllers + with hi3670 specific extensions. + - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extensions. + - "hisilicon,hi6220-dw-mshc": for controllers with hi6220 specific extensions. + +Optional Properties: +- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral. + +Example: + + /* for Hi3620 */ + + /* SoC portion */ + dwmmc_0: dwmmc0@fcd03000 { + compatible = "hisilicon,hi4511-dw-mshc"; + reg = <0xfcd03000 0x1000>; + interrupts = <0 16 4>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&mmc_clock HI3620_SD_CIUCLK>, <&clock HI3620_DDRC_PER_CLK>; + clock-names = "ciu", "biu"; + }; + + /* Board portion */ + dwmmc0@fcd03000 { + vmmc-supply = <&ldo12>; + fifo-depth = <0x100>; + pinctrl-names = "default"; + pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>; + bus-width = <4>; + disable-wp; + cd-gpios = <&gpio10 3 0>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + + /* for Hi6220 */ + + dwmmc_1: dwmmc1@f723e000 { + compatible = "hisilicon,hi6220-dw-mshc"; + bus-width = <0x4>; + disable-wp; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + card-detect-delay = <200>; + hisilicon,peripheral-syscon = <&ao_ctrl>; + reg = <0x0 0xf723e000 0x0 0x1000>; + interrupts = <0x0 0x49 0x4>; + clocks = <&clock_sys HI6220_MMC1_CIUCLK>, <&clock_sys HI6220_MMC1_CLK>; + clock-names = "ciu", "biu"; + cd-gpios = <&gpio1 0 1>; + pinctrl-names = "default", "idle"; + pinctrl-0 = <&sd_pmx_func &sd_clk_cfg_func &sd_cfg_func>; + pinctrl-1 = <&sd_pmx_idle &sd_clk_cfg_idle &sd_cfg_idle>; + vqmmc-supply = <&ldo7>; + vmmc-supply = <&ldo10>; + }; diff --git a/Documentation/devicetree/bindings/mmc/litex,mmc.yaml b/Documentation/devicetree/bindings/mmc/litex,mmc.yaml new file mode 100644 index 000000000..ef9e0da44 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/litex,mmc.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/litex,mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LiteX LiteSDCard device + +maintainers: + - Gabriel Somlo <gsomlo@gmail.com> + +description: | + LiteSDCard is a small footprint, configurable SDCard core for FPGA based + system on chips. + + The hardware source is Open Source and can be found on at + https://github.com/enjoy-digital/litesdcard/. + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + const: litex,mmc + + reg: + items: + - description: PHY registers + - description: CORE registers + - description: DMA Reader buffer + - description: DMA Writer buffer + - description: IRQ registers + minItems: 4 + + reg-names: + items: + - const: phy + - const: core + - const: reader + - const: writer + - const: irq + minItems: 4 + + clocks: + maxItems: 1 + description: + Handle to reference clock. + + vmmc-supply: + description: + Handle to fixed-voltage supply for the card power. + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - clocks + - vmmc-supply + +additionalProperties: false + +examples: + - | + mmc: mmc@12005000 { + compatible = "litex,mmc"; + reg = <0x12005000 0x100>, + <0x12003800 0x100>, + <0x12003000 0x100>, + <0x12004800 0x100>, + <0x12004000 0x100>; + reg-names = "phy", "core", "reader", "writer", "irq"; + clocks = <&reference_clk>; + vmmc-supply = <&vreg_mmc>; + interrupts = <4>; + }; diff --git a/Documentation/devicetree/bindings/mmc/marvell,dove-sdhci.yaml b/Documentation/devicetree/bindings/mmc/marvell,dove-sdhci.yaml new file mode 100644 index 000000000..7c9c652ad --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/marvell,dove-sdhci.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/marvell,dove-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell sdhci-dove controller + +maintainers: + - Adrian Hunter <adrian.hunter@intel.com> + - Ulf Hansson <ulf.hansson@linaro.org> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + const: marvell,dove-sdhci + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + sdio0: mmc@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>; + clocks = <&gate_clk 9>; + }; diff --git a/Documentation/devicetree/bindings/mmc/marvell,orion-sdio.yaml b/Documentation/devicetree/bindings/mmc/marvell,orion-sdio.yaml new file mode 100644 index 000000000..8a97ded15 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/marvell,orion-sdio.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/marvell,orion-sdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell orion-sdio controller + +maintainers: + - Nicolas Pitre <nico@fluxnic.net> + - Ulf Hansson <ulf.hansson@linaro.org> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + const: marvell,orion-sdio + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + mmc@d00d4000 { + compatible = "marvell,orion-sdio"; + reg = <0xd00d4000 0x200>; + interrupts = <54>; + clocks = <&gateclk 17>; + }; diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.yaml b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.yaml new file mode 100644 index 000000000..3ee758886 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.yaml @@ -0,0 +1,277 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Xenon SDHCI Controller + +description: | + This file documents differences between the core MMC properties described by + mmc-controller.yaml and the properties used by the Xenon implementation. + + Multiple SDHCs might be put into a single Xenon IP, to save size and cost. + Each SDHC is independent and owns independent resources, such as register + sets, clock and PHY. + + Each SDHC should have an independent device tree node. + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +properties: + compatible: + oneOf: + - enum: + - marvell,armada-cp110-sdhci + - marvell,armada-ap806-sdhci + + - items: + - const: marvell,armada-ap807-sdhci + - const: marvell,armada-ap806-sdhci + + - items: + - const: marvell,armada-3700-sdhci + - const: marvell,sdhci-xenon + + reg: + minItems: 1 + maxItems: 2 + description: | + For "marvell,armada-3700-sdhci", two register areas. The first one + for Xenon IP register. The second one for the Armada 3700 SoC PHY PAD + Voltage Control register. Please follow the examples with compatible + "marvell,armada-3700-sdhci" in below. + Please also check property marvell,pad-type in below. + + For other compatible strings, one register area for Xenon IP. + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: core + - const: axi + + interrupts: + maxItems: 1 + + marvell,xenon-sdhc-id: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: | + Indicate the corresponding bit index of current SDHC in SDHC System + Operation Control Register Bit[7:0]. Set/clear the corresponding bit to + enable/disable current SDHC. + + marvell,xenon-phy-type: + $ref: /schemas/types.yaml#/definitions/string + enum: + - "emmc 5.1 phy" + - "emmc 5.0 phy" + description: | + Xenon support multiple types of PHYs. To select eMMC 5.1 PHY, set: + marvell,xenon-phy-type = "emmc 5.1 phy" eMMC 5.1 PHY is the default + choice if this property is not provided. To select eMMC 5.0 PHY, set: + marvell,xenon-phy-type = "emmc 5.0 phy" + + All those types of PHYs can support eMMC, SD and SDIO. Please note that + this property only presents the type of PHY. It doesn't stand for the + entire SDHC type or property. For example, "emmc 5.1 phy" doesn't mean + that this Xenon SDHC only supports eMMC 5.1. + + marvell,xenon-phy-znr: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0x1f + default: 0xf + description: | + Set PHY ZNR value. + Only available for eMMC PHY. + + marvell,xenon-phy-zpr: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0x1f + default: 0xf + description: | + Set PHY ZPR value. + Only available for eMMC PHY. + + marvell,xenon-phy-nr-success-tun: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + default: 0x4 + description: | + Set the number of required consecutive successful sampling points + used to identify a valid sampling window, in tuning process. + + marvell,xenon-phy-tun-step-divider: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 64 + description: | + Set the divider for calculating TUN_STEP. + + marvell,xenon-phy-slow-mode: + type: boolean + description: | + If this property is selected, transfers will bypass PHY. + Only available when bus frequency lower than 55MHz in SDR mode. + Disabled by default. Please only try this property if timing issues + always occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25, + SD Default Speed and HS mode and eMMC legacy speed mode. + + marvell,xenon-tun-count: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0x9 + description: | + Xenon SDHC SoC usually doesn't provide re-tuning counter in + Capabilities Register 3 Bit[11:8]. + This property provides the re-tuning counter. + +allOf: + - $ref: mmc-controller.yaml# + - if: + properties: + compatible: + contains: + const: marvell,armada-3700-sdhci + + then: + properties: + reg: + items: + - description: Xenon IP registers + - description: Armada 3700 SoC PHY PAD Voltage Control register + + marvell,pad-type: + $ref: /schemas/types.yaml#/definitions/string + enum: + - sd + - fixed-1-8v + description: | + Type of Armada 3700 SoC PHY PAD Voltage Controller register. + If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning + and is switched to 1.8V when later in higher speed mode. + If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for + eMMC. + Please follow the examples with compatible + "marvell,armada-3700-sdhci" in below. + + required: + - marvell,pad-type + + - if: + properties: + compatible: + contains: + enum: + - marvell,armada-cp110-sdhci + - marvell,armada-ap807-sdhci + - marvell,armada-ap806-sdhci + + then: + properties: + clocks: + minItems: 2 + + clock-names: + items: + - const: core + - const: axi + + +required: + - compatible + - reg + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + // For eMMC + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@aa0000 { + compatible = "marvell,armada-ap807-sdhci", "marvell,armada-ap806-sdhci"; + reg = <0xaa0000 0x1000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&emmc_clk 0>, <&axi_clk 0>; + clock-names = "core", "axi"; + bus-width = <4>; + marvell,xenon-phy-slow-mode; + marvell,xenon-tun-count = <11>; + non-removable; + no-sd; + no-sdio; + + /* Vmmc and Vqmmc are both fixed */ + }; + + - | + // For SD/SDIO + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@ab0000 { + compatible = "marvell,armada-cp110-sdhci"; + reg = <0xab0000 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + vqmmc-supply = <&sd_vqmmc_regulator>; + vmmc-supply = <&sd_vmmc_regulator>; + clocks = <&sdclk 0>, <&axi_clk 0>; + clock-names = "core", "axi"; + bus-width = <4>; + marvell,xenon-tun-count = <9>; + }; + + - | + // For eMMC with compatible "marvell,armada-3700-sdhci": + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@aa0000 { + compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon"; + reg = <0xaa0000 0x1000>, + <0x17808 0x4>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&emmcclk 0>; + clock-names = "core"; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + non-removable; + no-sd; + no-sdio; + + /* Vmmc and Vqmmc are both fixed */ + + marvell,pad-type = "fixed-1-8v"; + }; + + - | + // For SD/SDIO with compatible "marvell,armada-3700-sdhci": + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@ab0000 { + compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon"; + reg = <0xab0000 0x1000>, + <0x17808 0x4>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + vqmmc-supply = <&sd_regulator>; + /* Vmmc is fixed */ + clocks = <&sdclk 0>; + clock-names = "core"; + bus-width = <4>; + + marvell,pad-type = "sd"; + }; diff --git a/Documentation/devicetree/bindings/mmc/microchip,dw-sparx5-sdhci.yaml b/Documentation/devicetree/bindings/mmc/microchip,dw-sparx5-sdhci.yaml new file mode 100644 index 000000000..69ff065c9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/microchip,dw-sparx5-sdhci.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/microchip,dw-sparx5-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Sparx5 Mobile Storage Host Controller Binding + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Lars Povlsen <lars.povlsen@microchip.com> + +# Everything else is described in the common file +properties: + compatible: + const: microchip,dw-sparx5-sdhci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: + Handle to "core" clock for the sdhci controller. + + clock-names: + items: + - const: core + + microchip,clock-delay: + description: Delay clock to card to meet setup time requirements. + Each step increase by 1.25ns. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 1 + maximum: 15 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/microchip,sparx5.h> + sdhci0: mmc@600800000 { + compatible = "microchip,dw-sparx5-sdhci"; + reg = <0x00800000 0x1000>; + pinctrl-0 = <&emmc_pins>; + pinctrl-names = "default"; + clocks = <&clks CLK_ID_AUX1>; + clock-names = "core"; + assigned-clocks = <&clks CLK_ID_AUX1>; + assigned-clock-rates = <800000000>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + bus-width = <8>; + microchip,clock-delay = <10>; + }; diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt new file mode 100644 index 000000000..f064528ef --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -0,0 +1,29 @@ +* Microchip PIC32 SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pic32 driver. + +Required properties: +- compatible: Should be "microchip,pic32mzda-sdhci" +- interrupts: Should contain interrupt +- clock-names: Should be "base_clk", "sys_clk". + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the SDHCI controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + + sdhci@1f8ec000 { + compatible = "microchip,pic32mzda-sdhci"; + reg = <0x1f8ec000 0x100>; + interrupts = <191 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rootclk REF4CLK>, <&rootclk PB5CLK>; + clock-names = "base_clk", "sys_clk"; + bus-width = <4>; + cap-sd-highspeed; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhc1>; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc-card.yaml b/Documentation/devicetree/bindings/mmc/mmc-card.yaml new file mode 100644 index 000000000..fd3471264 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-card.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-card.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MMC Card / eMMC Generic + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +description: | + This documents describes the devicetree bindings for a mmc-host controller + child node describing a mmc-card / an eMMC. + +properties: + compatible: + const: mmc-card + + reg: + const: 0 + + broken-hpi: + $ref: /schemas/types.yaml#/definitions/flag + description: + Use this to indicate that the mmc-card has a broken hpi + implementation, and that hpi should not be used. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + mmc { + #address-cells = <1>; + #size-cells = <0>; + + card@0 { + compatible = "mmc-card"; + reg = <0>; + broken-hpi; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml new file mode 100644 index 000000000..802e3ca8b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -0,0 +1,388 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MMC Controller Generic Binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +description: | + These properties are common to multiple MMC host controllers. Any host + that requires the respective functionality should implement them using + these definitions. + + It is possible to assign a fixed index mmcN to an MMC host controller + (and the corresponding mmcblkN devices) by defining an alias in the + /aliases device tree node. + +properties: + $nodename: + pattern: "^mmc(@.*)?$" + + "#address-cells": + const: 1 + description: | + The cell is the slot ID if a function subnode is used. + + "#size-cells": + const: 0 + + # Card Detection. + # If none of these properties are supplied, the host native card + # detect will be used. Only one of them should be provided. + + broken-cd: + $ref: /schemas/types.yaml#/definitions/flag + description: + There is no card detection available; polling must be used. + + cd-gpios: + maxItems: 1 + description: + The card detection will be done using the GPIO provided. + + non-removable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Non-removable slot (like eMMC); assume always present. + + # *NOTE* on CD and WP polarity. To use common for all SD/MMC host + # controllers line polarity properties, we have to fix the meaning + # of the "normal" and "inverted" line levels. We choose to follow + # the SDHCI standard, which specifies both those lines as "active + # low." Therefore, using the "cd-inverted" property means, that the + # CD line is active high, i.e. it is high, when a card is + # inserted. Similar logic applies to the "wp-inverted" property. + # + # CD and WP lines can be implemented on the hardware in one of two + # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or + # as dedicated pins. Polarity of dedicated pins can be specified, + # using *-inverted properties. GPIO polarity can also be specified + # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the + # latter case. We choose to use the XOR logic for GPIO CD and WP + # lines. This means, the two properties are "superimposed," for + # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the + # respective *-inverted property property results in a + # double-inversion and actually means the "normal" line polarity is + # in effect. + wp-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: + The Write Protect line polarity is inverted. + + cd-inverted: + $ref: /schemas/types.yaml#/definitions/flag + description: + The CD line polarity is inverted. + + # Other properties + + bus-width: + description: + Number of data lines. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 4, 8] + default: 1 + + max-frequency: + description: | + Maximum operating frequency of the bus: + - for eMMC, the maximum supported frequency is 200MHz, + - for SD/SDIO cards the SDR104 mode has a max supported + frequency of 208MHz, + - some mmc host controllers do support a max frequency upto + 384MHz. + So, lets keep the maximum supported value here. + + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 400000 + maximum: 384000000 + + disable-wp: + $ref: /schemas/types.yaml#/definitions/flag + description: + When set, no physical write-protect line is present. This + property should only be specified when the controller has a + dedicated write-protect detection logic. If a GPIO is always used + for the write-protect detection logic, it is sufficient to not + specify the wp-gpios property in the absence of a write-protect + line. Not used in combination with eMMC or SDIO. + + wp-gpios: + maxItems: 1 + description: + GPIO to use for the write-protect detection. + + cd-debounce-delay-ms: + description: + Set delay time before detecting card after card insert + interrupt. + + no-1-8-v: + $ref: /schemas/types.yaml#/definitions/flag + description: + When specified, denotes that 1.8V card voltage is not supported + on this system, even if the controller claims it. + + cap-sd-highspeed: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD high-speed timing is supported. + + cap-mmc-highspeed: + $ref: /schemas/types.yaml#/definitions/flag + description: + MMC high-speed timing is supported. + + sd-uhs-sdr12: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR12 speed is supported. + + sd-uhs-sdr25: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR25 speed is supported. + + sd-uhs-sdr50: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR50 speed is supported. + + sd-uhs-sdr104: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS SDR104 speed is supported. + + sd-uhs-ddr50: + $ref: /schemas/types.yaml#/definitions/flag + description: + SD UHS DDR50 speed is supported. + + cap-power-off-card: + $ref: /schemas/types.yaml#/definitions/flag + description: + Powering off the card is safe. + + cap-mmc-hw-reset: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC hardware reset is supported + + cap-sdio-irq: + $ref: /schemas/types.yaml#/definitions/flag + description: + enable SDIO IRQ signalling on this interface + + full-pwr-cycle: + $ref: /schemas/types.yaml#/definitions/flag + description: + Full power cycle of the card is supported. + + full-pwr-cycle-in-suspend: + $ref: /schemas/types.yaml#/definitions/flag + description: + Full power cycle of the card in suspend is supported. + + mmc-ddr-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (1.2V I/O) is supported. + + mmc-ddr-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (1.8V I/O) is supported. + + mmc-ddr-3_3v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC high-speed DDR mode (3.3V I/O) is supported. + + mmc-hs200-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS200 mode (1.2V I/O) is supported. + + mmc-hs200-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS200 mode (1.8V I/O) is supported. + + mmc-hs400-1_2v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 mode (1.2V I/O) is supported. + + mmc-hs400-1_8v: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 mode (1.8V I/O) is supported. + + mmc-hs400-enhanced-strobe: + $ref: /schemas/types.yaml#/definitions/flag + description: + eMMC HS400 enhanced strobe mode is supported + + no-mmc-hs400: + $ref: /schemas/types.yaml#/definitions/flag + description: + All eMMC HS400 modes are not supported. + + dsr: + description: + Value the card Driver Stage Register (DSR) should be programmed + with. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0xffff + + no-sdio: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send SDIO commands during + initialization. + + no-sd: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send SD commands during initialization. + + no-mmc: + $ref: /schemas/types.yaml#/definitions/flag + description: + Controller is limited to send MMC commands during + initialization. + + fixed-emmc-driver-type: + description: + For non-removable eMMC, enforce this driver type. The value is + the driver type as specified in the eMMC specification (table + 206 in spec version 5.1) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 4 + + post-power-on-delay-ms: + description: + It was invented for MMC pwrseq-simple which could be referred to + mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay + waiting for I/O signalling and card power supply to be stable, + regardless of whether pwrseq-simple is used. Default to 10ms if + no available. + default: 10 + + supports-cqe: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the corresponding + MMC host controller supports HW command queue feature. + + disable-cqe-dcmd: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the MMC + controller\'s command queue engine (CQE) does not support direct + commands (DCMDs). + + keep-power-in-suspend: + $ref: /schemas/types.yaml#/definitions/flag + description: + SDIO only. Preserves card power during a suspend/resume cycle. + + # Deprecated: enable-sdio-wakeup + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + SDIO only. Enables wake up of host system on SDIO IRQ assertion. + + vmmc-supply: + description: + Supply for the card power + + vqmmc-supply: + description: + Supply for the bus IO line power, such as a level shifter. + If the level shifter is controlled by a GPIO line, this shall + be modeled as a "regulator-fixed" with a GPIO line for + switching the level shifter on/off. + + mmc-pwrseq: + $ref: /schemas/types.yaml#/definitions/phandle + description: + System-on-Chip designs may specify a specific MMC power + sequence. To successfully detect an (e)MMC/SD/SDIO card, that + power sequence must be maintained while initializing the card. + +patternProperties: + "^.*@[0-9]+$": + type: object + description: | + On embedded systems the cards connected to a host may need + additional properties. These can be specified in subnodes to the + host controller node. The subnodes are identified by the + standard \'reg\' property. Which information exactly can be + specified depends on the bindings for the SDIO function driver + for the subnode, as specified by the compatible string. + + properties: + compatible: + description: | + Name of SDIO function following generic names recommended + practice + + reg: + items: + - minimum: 0 + maximum: 7 + description: + Must contain the SDIO function number of the function this + subnode describes. A value of 0 denotes the memory SD + function, values from 1 to 7 denote the SDIO functions. + + required: + - reg + + "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$": + $ref: /schemas/types.yaml#/definitions/uint32-array + + minItems: 2 + maxItems: 2 + items: + minimum: 0 + maximum: 359 + description: + Set the clock (phase) delays which are to be configured in the + controller while switching to particular speed mode. These values + are in pair of degrees. + +dependencies: + cd-debounce-delay-ms: [ cd-gpios ] + fixed-emmc-driver-type: [ non-removable ] + +additionalProperties: true + +examples: + - | + mmc3: mmc@1c12000 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1c12000 0x200>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&sdhci0_pwrseq>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; + interrupt-names = "host-wake"; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.yaml b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.yaml new file mode 100644 index 000000000..1fc7e620f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-pwrseq-emmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple eMMC hardware reset provider binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +description: + The purpose of this driver is to perform standard eMMC hw reset + procedure, as described by Jedec 4.4 specification. This procedure is + performed just after MMC core enabled power to the given mmc host (to + fix possible issues if bootloader has left eMMC card in initialized or + unknown state), and before performing complete system reboot (also in + case of emergency reboot call). The latter is needed on boards, which + doesn't have hardware reset logic connected to emmc card and (limited or + broken) ROM bootloaders are unable to read second stage from the emmc + card if the card is left in unknown or already initialized state. + +properties: + compatible: + const: mmc-pwrseq-emmc + + reset-gpios: + minItems: 1 + description: + contains a GPIO specifier. The reset GPIO is asserted + and then deasserted to perform eMMC card reset. To perform + reset procedure as described in Jedec 4.4 specification, the + gpio line should be defined as GPIO_ACTIVE_LOW. + +required: + - compatible + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + sdhci0_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; +... diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.yaml b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.yaml new file mode 100644 index 000000000..9e2396751 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-sd8787.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-pwrseq-sd8787.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell SD8787 power sequence provider binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +properties: + compatible: + enum: + - mmc-pwrseq-sd8787 + - mmc-pwrseq-wilc1000 + + powerdown-gpios: + minItems: 1 + description: + contains a power down GPIO specifier with the default active state + + reset-gpios: + minItems: 1 + description: + contains a reset GPIO specifier with the default active state + +required: + - compatible + - powerdown-gpios + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-sd8787"; + powerdown-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; + reset-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; + }; +... diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml new file mode 100644 index 000000000..226fb1919 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-pwrseq-simple.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple MMC power sequence provider binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +description: + The purpose of the simple MMC power sequence provider is to supports a set + of common properties between various SOC designs. It thus enables us to use + the same provider for several SOC designs. + +properties: + compatible: + const: mmc-pwrseq-simple + + reset-gpios: + minItems: 1 + # Put some limit to avoid false warnings + maxItems: 32 + description: + contains a list of GPIO specifiers. The reset GPIOs are asserted + at initialization and prior we start the power up procedure of the card. + They will be de-asserted right after the power has been provided to the + card. + + clocks: + minItems: 1 + description: Handle for the entry in clock-names. + + clock-names: + items: + - const: ext_clock + description: External clock provided to the card. + + post-power-on-delay-ms: + description: + Delay in ms after powering the card and de-asserting the + reset-gpios (if any). + + power-off-delay-us: + description: + Delay in us after asserting the reset-gpios (if any) + during power off of the card. + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + sdhci0_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + clocks = <&clk_32768_ck>; + clock-names = "ext_clock"; + }; +... diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml new file mode 100644 index 000000000..c0662ce99 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mmc-spi-slot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MMC/SD/SDIO slot directly connected to a SPI bus + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +allOf: + - $ref: "mmc-controller.yaml" + - $ref: /schemas/spi/spi-peripheral-props.yaml + +description: | + The extra properties used by an mmc connected via SPI. + +properties: + compatible: + const: mmc-spi-slot + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + voltage-ranges: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Two cells are required, first cell specifies minimum slot voltage (mV), + second cell specifies maximum slot voltage (mV). + items: + - description: | + value for minimum slot voltage in mV + default: 3200 + - description: | + value for maximum slot voltage in mV + default: 3400 + + gpios: + description: | + For historical reasons, this does not follow the generic mmc-controller + binding. + minItems: 1 + items: + - description: Card-Detect GPIO + - description: Write-Protect GPIO + +required: + - compatible + - reg + - spi-max-frequency + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + mmc@0 { + compatible = "mmc-spi-slot"; + reg = <0>; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>, <&gpio 15 GPIO_ACTIVE_HIGH>; + voltage-ranges = <3300 3300>; + spi-max-frequency = <50000000>; + interrupts = <42>; + interrupt-parent = <&PIC>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt new file mode 100644 index 000000000..bf9d7d3fe --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -0,0 +1 @@ +This file has moved to mmc-controller.yaml. diff --git a/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt b/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt new file mode 100644 index 000000000..b63819149 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/moxa,moxart-mmc.txt @@ -0,0 +1,30 @@ +MOXA ART MMC Host Controller Interface + + Inherits from mmc binding[1]. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Required properties: + +- compatible : Must be "moxa,moxart-mmc" or "faraday,ftsdc010" +- reg : Should contain registers location and length +- interrupts : Should contain the interrupt number +- clocks : Should contain phandle for the clock feeding the MMC controller + +Optional properties: + +- dmas : Should contain two DMA channels, line request number must be 5 for + both channels +- dma-names : Must be "tx", "rx" + +Example: + + mmc: mmc@98e00000 { + compatible = "moxa,moxart-mmc"; + reg = <0x98e00000 0x5C>; + interrupts = <5 0>; + clocks = <&clk_apb>; + dmas = <&dma 5>, + <&dma 5>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml new file mode 100644 index 000000000..d8e1e2e9a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml @@ -0,0 +1,258 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mtk-sd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MTK MSDC Storage Host Controller Binding + +maintainers: + - Chaotian Jing <chaotian.jing@mediatek.com> + - Wenbin Mei <wenbin.mei@mediatek.com> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt2701-mmc + - mediatek,mt2712-mmc + - mediatek,mt6779-mmc + - mediatek,mt6795-mmc + - mediatek,mt7620-mmc + - mediatek,mt7622-mmc + - mediatek,mt8135-mmc + - mediatek,mt8173-mmc + - mediatek,mt8183-mmc + - mediatek,mt8516-mmc + - items: + - const: mediatek,mt7623-mmc + - const: mediatek,mt2701-mmc + - items: + - enum: + - mediatek,mt8186-mmc + - mediatek,mt8188-mmc + - mediatek,mt8192-mmc + - mediatek,mt8195-mmc + - const: mediatek,mt8183-mmc + + reg: + minItems: 1 + items: + - description: base register (required). + - description: top base register (required for MT8183). + + clocks: + description: + Should contain phandle for the clock feeding the MMC controller. + minItems: 2 + items: + - description: source clock (required). + - description: HCLK which used for host (required). + - description: independent source clock gate (required for MT2712). + - description: bus clock used for internal register access (required for MT2712 MSDC0/3). + - description: msdc subsys clock gate (required for MT8192). + - description: peripheral bus clock gate (required for MT8192). + - description: AXI bus clock gate (required for MT8192). + - description: AHB bus clock gate (required for MT8192). + + clock-names: + minItems: 2 + items: + - const: source + - const: hclk + - const: source_cg + - const: bus_clk + - const: sys_cg + - const: pclk_cg + - const: axi_cg + - const: ahb_cg + + interrupts: + description: + Should at least contain MSDC GIC interrupt. To support SDIO in-band wakeup, an extended + interrupt is required and be configured as wakeup source irq. + minItems: 1 + maxItems: 2 + + interrupt-names: + items: + - const: msdc + - const: sdio_wakeup + + pinctrl-names: + description: + Should at least contain default and state_uhs. To support SDIO in-band wakeup, dat1 pin + will be switched between GPIO mode and SDIO DAT1 mode, state_eint is mandatory in this + scenario. + minItems: 2 + items: + - const: default + - const: state_uhs + - const: state_eint + + pinctrl-0: + description: + should contain default/high speed pin ctrl. + maxItems: 1 + + pinctrl-1: + description: + should contain uhs mode pin ctrl. + maxItems: 1 + + pinctrl-2: + description: + should switch dat1 pin to GPIO mode. + maxItems: 1 + + assigned-clocks: + description: + PLL of the source clock. + maxItems: 1 + + assigned-clock-parents: + description: + parent of source clock, used for HS400 mode to get 400Mhz source clock. + maxItems: 1 + + hs400-ds-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + HS400 DS delay setting. + minimum: 0 + maximum: 0xffffffff + + mediatek,hs200-cmd-int-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + HS200 command internal delay setting. + This field has total 32 stages. + The value is an integer from 0 to 31. + minimum: 0 + maximum: 31 + + mediatek,hs400-cmd-int-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + HS400 command internal delay setting. + This field has total 32 stages. + The value is an integer from 0 to 31. + minimum: 0 + maximum: 31 + + mediatek,hs400-cmd-resp-sel-rising: + $ref: /schemas/types.yaml#/definitions/flag + description: + HS400 command response sample selection. + If present, HS400 command responses are sampled on rising edges. + If not present, HS400 command responses are sampled on falling edges. + + mediatek,hs400-ds-dly3: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Gear of the third delay line for DS for input data latch in data + pad macro, there are 32 stages from 0 to 31. + For different corner IC, the time is different about one step, it is + about 100ps. + The value is confirmed by doing scan and calibration to find a best + value with corner IC and it is valid only for HS400 mode. + minimum: 0 + maximum: 31 + + mediatek,latch-ck: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Some SoCs do not support enhance_rx, need set correct latch-ck to avoid + data crc error caused by stop clock(fifo full) Valid range = [0:0x7]. + if not present, default value is 0. + applied to compatible "mediatek,mt2701-mmc". + minimum: 0 + maximum: 7 + + resets: + maxItems: 1 + + reset-names: + const: hrst + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - pinctrl-names + - pinctrl-0 + - pinctrl-1 + - vmmc-supply + - vqmmc-supply + +if: + properties: + compatible: + contains: + const: mediatek,mt8183-mmc +then: + properties: + reg: + minItems: 2 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8173-clk.h> + mmc0: mmc@11230000 { + compatible = "mediatek,mt8173-mmc"; + reg = <0x11230000 0x1000>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; + vmmc-supply = <&mt6397_vemc_3v3_reg>; + vqmmc-supply = <&mt6397_vio18_reg>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clock-names = "source", "hclk"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; + mediatek,hs200-cmd-int-delay = <26>; + mediatek,hs400-cmd-int-delay = <14>; + mediatek,hs400-cmd-resp-sel-rising; + }; + + mmc3: mmc@11260000 { + compatible = "mediatek,mt8173-mmc"; + reg = <0x11260000 0x1000>; + clock-names = "source", "hclk"; + clocks = <&pericfg CLK_PERI_MSDC30_3>, + <&topckgen CLK_TOP_MSDC50_2_H_SEL>; + interrupt-names = "msdc", "sdio_wakeup"; + interrupts-extended = <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_LOW 0>, + <&pio 23 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default", "state_uhs", "state_eint"; + pinctrl-0 = <&mmc2_pins_default>; + pinctrl-1 = <&mmc2_pins_uhs>; + pinctrl-2 = <&mmc2_pins_eint>; + bus-width = <4>; + max-frequency = <200000000>; + cap-sd-highspeed; + sd-uhs-sdr104; + keep-power-in-suspend; + wakeup-source; + cap-sdio-irq; + no-mmc; + no-sd; + non-removable; + vmmc-supply = <&sdio_fixed_3v3>; + vqmmc-supply = <&mt6397_vgp3_reg>; + mmc-pwrseq = <&wifi_pwrseq>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.yaml b/Documentation/devicetree/bindings/mmc/mxs-mmc.yaml new file mode 100644 index 000000000..bec8f8c71 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS MMC controller + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + +description: | + The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller + to support MMC, SD, and SDIO types of memory cards. + + This file documents differences between the core properties in mmc.txt + and the properties used by the mxsmmc driver. + +allOf: + - $ref: "mmc-controller.yaml" + +properties: + compatible: + enum: + - fsl,imx23-mmc + - fsl,imx28-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + +required: + - compatible + - reg + - interrupts + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + mmc@80010000 { + compatible = "fsl,imx28-mmc"; + reg = <0x80010000 2000>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; + bus-width = <8>; + }; diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.yaml b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.yaml new file mode 100644 index 000000000..fe0270207 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.yaml @@ -0,0 +1,314 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/nvidia,tegra20-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra Secure Digital Host Controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + This controller on Tegra family SoCs provides an interface for MMC, SD, and + SDIO types of memory cards. + + This file documents differences between the core properties described by + mmc-controller.yaml and the properties for the Tegra SDHCI controller. + +properties: + compatible: + oneOf: + - enum: + - nvidia,tegra20-sdhci + - nvidia,tegra30-sdhci + - nvidia,tegra114-sdhci + - nvidia,tegra124-sdhci + - nvidia,tegra210-sdhci + - nvidia,tegra186-sdhci + - nvidia,tegra194-sdhci + + - items: + - const: nvidia,tegra132-sdhci + - const: nvidia,tegra124-sdhci + + - items: + - enum: + - nvidia,tegra194-sdhci + - nvidia,tegra234-sdhci + - const: nvidia,tegra186-sdhci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + maxItems: 2 + + resets: + items: + - description: module reset + + reset-names: + items: + - const: sdhci + + power-gpios: + description: specify GPIOs for power control + maxItems: 1 + + interconnects: + items: + - description: memory read client + - description: memory write client + + interconnect-names: + items: + - const: dma-mem # read + - const: write + + iommus: + maxItems: 1 + + operating-points-v2: + $ref: "/schemas/types.yaml#/definitions/phandle" + + power-domains: + items: + - description: phandle to the core power domain + + nvidia,default-tap: + description: Specify the default inbound sampling clock trimmer value for + non-tunable modes. + + The values are used for compensating trace length differences by + adjusting the sampling point. The values are programmed to the Vendor + Clock Control Register. Please refer to the reference manual of the SoC + for correct values. + + The DQS trim values are only used on controllers which support HS400 + timing. Only SDMMC4 on Tegra210 and Tegra186 supports HS400. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,default-trim: + description: Specify the default outbound clock trimmer value. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,dqs-trim: + description: Specify DQS trim value for HS400 timing. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-1v8: + description: Specify drive strength calibration offsets for 1.8 V + signaling modes. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-1v8-timeout: + description: Specify drive strength used as a fallback in case the + automatic calibration times out on a 1.8 V signaling mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-3v3: + description: Specify drive strength calibration offsets for 3.3 V + signaling modes. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-3v3-timeout: + description: Specify drive strength used as a fallback in case the + automatic calibration times out on a 3.3 V signaling mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-sdr104: + description: Specify drive strength calibration offsets for SDR104 mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-down-offset-hs400: + description: Specify drive strength calibration offsets for HS400 mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-1v8: + description: Specify drive strength calibration offsets for 1.8 V + signaling modes. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-1v8-timeout: + description: Specify drive strength used as a fallback in case the + automatic calibration times out on a 1.8 V signaling mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-3v3: + description: Specify drive strength calibration offsets for 3.3 V + signaling modes. + + The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the SDHCI_TEGRA_AUTO_CAL_CONFIG + register. A higher value corresponds to higher drive strength. Please + refer to the reference manual of the SoC for correct values. The SDR104 + and HS400 timing specific values are used in corresponding modes if + specified. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-3v3-timeout: + description: Specify drive strength used as a fallback in case the + automatic calibration times out on a 3.3 V signaling mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-sdr104: + description: Specify drive strength calibration offsets for SDR104 mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,pad-autocal-pull-up-offset-hs400: + description: Specify drive strength calibration offsets for HS400 mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + nvidia,only-1-8v: + description: The presence of this property indicates that the controller + operates at a 1.8 V fixed I/O voltage. + $ref: "/schemas/types.yaml#/definitions/flag" + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - reset-names + +allOf: + - $ref: "mmc-controller.yaml" + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra20-sdhci + - nvidia,tegra30-sdhci + - nvidia,tegra114-sdhci + - nvidia,tegra124-sdhci + then: + properties: + clocks: + items: + - description: module clock + else: + properties: + clocks: + items: + - description: module clock + - description: timeout clock + + clock-names: + items: + - const: sdhci + - const: tmclk + required: + - clock-names + + - if: + properties: + compatible: + contains: + const: nvidia,tegra210-sdhci + then: + properties: + pinctrl-names: + oneOf: + - items: + - const: sdmmc-3v3 + description: pad configuration for 3.3 V + - const: sdmmc-1v8 + description: pad configuration for 1.8 V + - const: sdmmc-3v3-drv + description: pull-up/down configuration for 3.3 V + - const: sdmmc-1v8-drv + description: pull-up/down configuration for 1.8 V + - items: + - const: sdmmc-3v3-drv + description: pull-up/down configuration for 3.3 V + - const: sdmmc-1v8-drv + description: pull-up/down configuration for 1.8 V + - items: + - const: sdmmc-1v8-drv + description: pull-up/down configuration for 1.8 V + required: + - clock-names + - if: + properties: + compatible: + contains: + enum: + - nvidia,tegra186-sdhci + - nvidia,tegra194-sdhci + then: + properties: + pinctrl-names: + items: + - const: sdmmc-3v3 + description: pad configuration for 3.3 V + - const: sdmmc-1v8 + description: pad configuration for 1.8 V + required: + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mmc@c8000200 { + compatible = "nvidia,tegra20-sdhci"; + reg = <0xc8000200 0x200>; + interrupts = <47>; + clocks = <&tegra_car 14>; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 155 0>; /* gpio PT3 */ + bus-width = <8>; + }; + + - | + #include <dt-bindings/clock/tegra210-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mmc@700b0000 { + compatible = "nvidia,tegra210-sdhci"; + reg = <0x700b0000 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>, + <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>; + clock-names = "sdhci", "tmclk"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8", + "sdmmc-3v3-drv", "sdmmc-1v8-drv"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + pinctrl-2 = <&sdmmc1_3v3_drv>; + pinctrl-3 = <&sdmmc1_1v8_drv>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + nvidia,default-tap = <0x2>; + nvidia,default-trim = <0x4>; + assigned-clocks = <&tegra_car TEGRA210_CLK_SDMMC4>, + <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>, + <&tegra_car TEGRA210_CLK_PLL_C4>; + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; + assigned-clock-rates = <200000000>, <1000000000>, <1000000000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/owl-mmc.yaml b/Documentation/devicetree/bindings/mmc/owl-mmc.yaml new file mode 100644 index 000000000..b0d81ebe0 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/owl-mmc.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/owl-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi Owl SoCs SD/MMC/SDIO controller + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + oneOf: + - const: actions,owl-mmc + - items: + - enum: + - actions,s500-mmc + - actions,s700-mmc + - const: actions,owl-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + resets: + maxItems: 1 + + dmas: + maxItems: 1 + + dma-names: + const: mmc + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + mmc0: mmc@e0330000 { + compatible = "actions,owl-mmc"; + reg = <0xe0330000 0x4000>; + interrupts = <0 42 4>; + clocks = <&cmu 56>; + resets = <&cmu 23>; + dmas = <&dma 2>; + dma-names = "mmc"; + bus-width = <4>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt new file mode 100644 index 000000000..5f5c2bec2 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt @@ -0,0 +1,25 @@ +* PXA MMC drivers + +Driver bindings for the PXA MCI (MMC/SDIO) interfaces + +Required properties: +- compatible: Should be "marvell,pxa-mmc". +- vmmc-supply: A regulator for VMMC + +Optional properties: +- marvell,detect-delay-ms: sets the detection delay timeout in ms. + +In addition to the properties described in this docuent, the details +described in mmc.txt are supported. + +Examples: + +mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + vmmc-supply = <&mmc_regulator>; + cd-gpios = <&gpio 23 0>; + wp-gpios = <&gpio 24 0>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml b/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml new file mode 100644 index 000000000..c36ba561c --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/renesas,mmcif.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Multi Media Card Interface (MMCIF) Controller + +maintainers: + - Wolfram Sang <wsa+renesas@sang-engineering.com> + +allOf: + - $ref: "mmc-controller.yaml" + +properties: + compatible: + items: + - enum: + - renesas,mmcif-r7s72100 # RZ/A1H + - renesas,mmcif-r8a73a4 # R-Mobile APE6 + - renesas,mmcif-r8a7740 # R-Mobile A1 + - renesas,mmcif-r8a7742 # RZ/G1H + - renesas,mmcif-r8a7743 # RZ/G1M + - renesas,mmcif-r8a7744 # RZ/G1N + - renesas,mmcif-r8a7745 # RZ/G1E + - renesas,mmcif-r8a7778 # R-Car M1A + - renesas,mmcif-r8a7790 # R-Car H2 + - renesas,mmcif-r8a7791 # R-Car M2-W + - renesas,mmcif-r8a7793 # R-Car M2-N + - renesas,mmcif-r8a7794 # R-Car E2 + - renesas,mmcif-sh73a0 # SH-Mobile AG5 + - const: renesas,sh-mmcif + + reg: + maxItems: 1 + + interrupts: true + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + + max-frequency: true + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + +if: + properties: + compatible: + contains: + const: renesas,mmcif-r7s72100 +then: + properties: + interrupts: + items: + - description: Error interrupt + - description: Normal operation interrupt + - description: Card detection interrupt +else: + if: + properties: + compatible: + contains: + enum: + - renesas,mmcif-r8a7740 + - renesas,mmcif-sh73a0 + then: + properties: + interrupts: + items: + - description: Error interrupt + - description: Normal operation interrupt + else: + if: + properties: + compatible: + contains: + enum: + - renesas,mmcif-r8a73a4 + - renesas,mmcif-r8a7778 + then: + properties: + interrupts: + maxItems: 1 + else: + properties: + interrupts: + maxItems: 1 + required: + - resets + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + mmcif0: mmc@ee200000 { + compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; + reg = <0xee200000 0x80>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 315>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 315>; + dmas = <&dmac0 0xd1>, <&dmac0 0xd2>, <&dmac1 0xd1>, <&dmac1 0xd2>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,sdhi.yaml b/Documentation/devicetree/bindings/mmc/renesas,sdhi.yaml new file mode 100644 index 000000000..0424b06cb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/renesas,sdhi.yaml @@ -0,0 +1,269 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mmc/renesas,sdhi.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas SDHI SD/MMC controller + +maintainers: + - Wolfram Sang <wsa+renesas@sang-engineering.com> + +properties: + compatible: + oneOf: + - items: + - const: renesas,sdhi-sh73a0 # R-Mobile APE6 + - items: + - const: renesas,sdhi-r7s72100 # RZ/A1H + - items: + - const: renesas,sdhi-r7s9210 # SH-Mobile AG5 + - items: + - const: renesas,sdhi-r8a73a4 # R-Mobile APE6 + - items: + - const: renesas,sdhi-r8a7740 # R-Mobile A1 + - items: + - enum: + - renesas,sdhi-r8a7778 # R-Car M1 + - renesas,sdhi-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-sdhi # R-Car Gen1 + - items: + - enum: + - renesas,sdhi-r8a7742 # RZ/G1H + - renesas,sdhi-r8a7743 # RZ/G1M + - renesas,sdhi-r8a7744 # RZ/G1N + - renesas,sdhi-r8a7745 # RZ/G1E + - renesas,sdhi-r8a77470 # RZ/G1C + - renesas,sdhi-r8a7790 # R-Car H2 + - renesas,sdhi-r8a7791 # R-Car M2-W + - renesas,sdhi-r8a7792 # R-Car V2H + - renesas,sdhi-r8a7793 # R-Car M2-N + - renesas,sdhi-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-sdhi # R-Car Gen2 and RZ/G1 + - items: + - const: renesas,sdhi-mmc-r8a77470 # RZ/G1C (SDHI/MMC IP) + - items: + - enum: + - renesas,sdhi-r8a774a1 # RZ/G2M + - renesas,sdhi-r8a774b1 # RZ/G2N + - renesas,sdhi-r8a774c0 # RZ/G2E + - renesas,sdhi-r8a774e1 # RZ/G2H + - renesas,sdhi-r8a7795 # R-Car H3 + - renesas,sdhi-r8a7796 # R-Car M3-W + - renesas,sdhi-r8a77961 # R-Car M3-W+ + - renesas,sdhi-r8a77965 # R-Car M3-N + - renesas,sdhi-r8a77970 # R-Car V3M + - renesas,sdhi-r8a77980 # R-Car V3H + - renesas,sdhi-r8a77990 # R-Car E3 + - renesas,sdhi-r8a77995 # R-Car D3 + - renesas,sdhi-r9a07g043 # RZ/G2UL + - renesas,sdhi-r9a07g044 # RZ/G2{L,LC} + - renesas,sdhi-r9a07g054 # RZ/V2L + - const: renesas,rcar-gen3-sdhi # R-Car Gen3 or RZ/G2 + - items: + - enum: + - renesas,sdhi-r8a779a0 # R-Car V3U + - renesas,sdhi-r8a779f0 # R-Car S4-8 + - const: renesas,rcar-gen4-sdhi # R-Car Gen4 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 3 + + clocks: true + + clock-names: true + + dmas: + minItems: 4 + maxItems: 4 + + dma-names: + minItems: 4 + maxItems: 4 + items: + enum: + - tx + - rx + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + pinctrl-0: + minItems: 1 + maxItems: 2 + + pinctrl-1: + maxItems: 1 + + pinctrl-names: true + + max-frequency: true + +allOf: + - $ref: "mmc-controller.yaml" + + - if: + properties: + compatible: + contains: + enum: + - renesas,sdhi-r9a07g043 + - renesas,sdhi-r9a07g044 + - renesas,sdhi-r9a07g054 + then: + properties: + clocks: + items: + - description: IMCLK, SDHI channel main clock1. + - description: CLK_HS, SDHI channel High speed clock which operates + 4 times that of SDHI channel main clock1. + - description: IMCLK2, SDHI channel main clock2. When this clock is + turned off, external SD card detection cannot be + detected. + - description: ACLK, SDHI channel bus clock. + clock-names: + items: + - const: core + - const: clkh + - const: cd + - const: aclk + required: + - clock-names + - resets + else: + if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-sdhi + - renesas,rcar-gen3-sdhi + - renesas,rcar-gen4-sdhi + then: + properties: + clocks: + minItems: 1 + maxItems: 3 + clock-names: + minItems: 1 + uniqueItems: true + items: + - const: core + - enum: [ clkh, cd ] + - const: cd + else: + properties: + clocks: + minItems: 1 + maxItems: 2 + clock-names: + minItems: 1 + items: + - const: core + - const: cd + + - if: + properties: + compatible: + contains: + const: renesas,sdhi-mmc-r8a77470 + then: + properties: + pinctrl-names: + items: + - const: state_uhs + else: + properties: + pinctrl-names: + minItems: 1 + items: + - const: default + - const: state_uhs + + - if: + properties: + compatible: + contains: + enum: + - renesas,sdhi-r7s72100 + - renesas,sdhi-r7s9210 + then: + required: + - clock-names + description: + The internal card detection logic that exists in these controllers is + sectioned off to be run by a separate second clock source to allow + the main core clock to be turned off to save power. + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + sdhi0: mmc@ee100000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0xee100000 0x328>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 314>; + dmas = <&dmac0 0xcd>, <&dmac0 0xce>, <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 314>; + }; + + sdhi1: mmc@ee120000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0xee120000 0x328>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 313>; + dmas = <&dmac0 0xc9>, <&dmac0 0xca>, <&dmac1 0xc9>, <&dmac1 0xca>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 313>; + }; + + sdhi2: mmc@ee140000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0xee140000 0x100>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 312>; + dmas = <&dmac0 0xc1>, <&dmac0 0xc2>, <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 312>; + }; + + sdhi3: mmc@ee160000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0xee160000 0x100>; + interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 311>; + dmas = <&dmac0 0xd3>, <&dmac0 0xd4>, <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 311>; + }; diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml new file mode 100644 index 000000000..95f59a5e3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/rockchip-dw-mshc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip designware mobile storage host controller + +description: + Rockchip uses the Synopsys designware mobile storage host controller + to interface a SoC with storage medium such as eMMC or SD/MMC cards. + This file documents the combined properties for the core Synopsys dw mshc + controller that are not already included in the synopsys-dw-mshc-common.yaml + file and the Rockchip specific extensions. + +allOf: + - $ref: "synopsys-dw-mshc-common.yaml#" + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +# Everything else is described in the common file +properties: + compatible: + oneOf: + # for Rockchip RK2928 and before RK3288 + - const: rockchip,rk2928-dw-mshc + # for Rockchip RK3288 + - const: rockchip,rk3288-dw-mshc + - items: + - enum: + - rockchip,px30-dw-mshc + - rockchip,rk1808-dw-mshc + - rockchip,rk3036-dw-mshc + - rockchip,rk3128-dw-mshc + - rockchip,rk3228-dw-mshc + - rockchip,rk3308-dw-mshc + - rockchip,rk3328-dw-mshc + - rockchip,rk3368-dw-mshc + - rockchip,rk3399-dw-mshc + - rockchip,rk3568-dw-mshc + - rockchip,rv1108-dw-mshc + - rockchip,rv1126-dw-mshc + - const: rockchip,rk3288-dw-mshc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 4 + description: + Handle to "biu" and "ciu" clocks for the bus interface unit clock and + the card interface unit clock. If "ciu-drive" and "ciu-sample" are + specified in clock-names, it should also contain + handles to these clocks. + + clock-names: + minItems: 2 + items: + - const: biu + - const: ciu + - const: ciu-drive + - const: ciu-sample + description: + Apart from the clock-names "biu" and "ciu" two more clocks + "ciu-drive" and "ciu-sample" are supported. They are used + to control the clock phases, "ciu-sample" is required for tuning + high speed modes. + + rockchip,default-sample-phase: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 360 + default: 0 + description: + The default phase to set "ciu-sample" at probing, + low speeds or in case where all phases work at tuning time. + If not specified 0 deg will be used. + + rockchip,desired-num-phases: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 360 + default: 360 + description: + The desired number of times that the host execute tuning when needed. + If not specified, the host will do tuning for 360 times, + namely tuning for each degree. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3288-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + sdmmc: mmc@ff0c0000 { + compatible = "rockchip,rk3288-dw-mshc"; + reg = <0xff0c0000 0x4000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, + <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + resets = <&cru SRST_MMC0>; + reset-names = "reset"; + fifo-depth = <0x100>; + max-frequency = <150000000>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/samsung,exynos-dw-mshc.yaml b/Documentation/devicetree/bindings/mmc/samsung,exynos-dw-mshc.yaml new file mode 100644 index 000000000..fdaa18481 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung,exynos-dw-mshc.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/samsung,exynos-dw-mshc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Samsung Exynos SoC specific extensions to the Synopsys Designware Mobile + Storage Host Controller + +maintainers: + - Jaehoon Chung <jh80.chung@samsung.com> + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + enum: + - samsung,exynos4210-dw-mshc + - samsung,exynos4412-dw-mshc + - samsung,exynos5250-dw-mshc + - samsung,exynos5420-dw-mshc + - samsung,exynos5420-dw-mshc-smu + - samsung,exynos7-dw-mshc + - samsung,exynos7-dw-mshc-smu + - axis,artpec8-dw-mshc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + description: + Handle to "biu" and "ciu" clocks for the + bus interface unit clock and the card interface unit clock. + + clock-names: + items: + - const: biu + - const: ciu + + samsung,dw-mshc-ciu-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: + The divider value for the card interface unit (ciu) clock. + + samsung,dw-mshc-ddr-timing: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: CIU clock phase shift value for tx mode + minimum: 0 + maximum: 7 + - description: CIU clock phase shift value for rx mode + minimum: 0 + maximum: 7 + description: + The value of CUI clock phase shift value in transmit mode and CIU clock + phase shift value in receive mode for double data rate mode operation. + See also samsung,dw-mshc-hs400-timing property. + + samsung,dw-mshc-hs400-timing: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: CIU clock phase shift value for tx mode + minimum: 0 + maximum: 7 + - description: CIU clock phase shift value for rx mode + minimum: 0 + maximum: 7 + description: | + The value of CIU TX and RX clock phase shift value for HS400 mode + operation. + Valid values for SDR and DDR CIU clock timing:: + - valid value for tx phase shift and rx phase shift is 0 to 7. + - when CIU clock divider value is set to 3, all possible 8 phase shift + values can be used. + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx + phase shift clocks should be 0. + If missing, values from samsung,dw-mshc-ddr-timing property are used. + + samsung,dw-mshc-sdr-timing: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: CIU clock phase shift value for tx mode + minimum: 0 + maximum: 7 + - description: CIU clock phase shift value for rx mode + minimum: 0 + maximum: 7 + description: + The value of CIU clock phase shift value in transmit mode and CIU clock + phase shift value in receive mode for single data rate mode operation. + See also samsung,dw-mshc-hs400-timing property. + + samsung,read-strobe-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + RCLK (Data strobe) delay to control HS400 mode (Latency value for delay + line in Read path). If missing, default from hardware is used. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - samsung,dw-mshc-ddr-timing + - samsung,dw-mshc-sdr-timing + +allOf: + - $ref: "synopsys-dw-mshc-common.yaml#" + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos5250-dw-mshc + - samsung,exynos5420-dw-mshc + - samsung,exynos7-dw-mshc + - samsung,exynos7-dw-mshc-smu + - axis,artpec8-dw-mshc + then: + required: + - samsung,dw-mshc-ciu-div + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mmc@12220000 { + compatible = "samsung,exynos5420-dw-mshc"; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x12220000 0x1000>; + clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>; + clock-names = "biu", "ciu"; + fifo-depth = <0x40>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_wp &sd2_bus1 &sd2_bus4>; + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <200000000>; + vmmc-supply = <&ldo19_reg>; + vqmmc-supply = <&ldo13_reg>; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; + }; diff --git a/Documentation/devicetree/bindings/mmc/samsung,s3c6410-sdhci.yaml b/Documentation/devicetree/bindings/mmc/samsung,s3c6410-sdhci.yaml new file mode 100644 index 000000000..5d873a60f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung,s3c6410-sdhci.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/samsung,s3c6410-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung SoC SDHCI Controller + +maintainers: + - Jaehoon Chung <jh80.chung@samsung.com> + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + enum: + - samsung,s3c6410-sdhci + - samsung,exynos4210-sdhci + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 5 + + clock-names: + minItems: 2 + items: + - const: hsmmc + - pattern: "^mmc_busclk.[0-3]$" + - pattern: "^mmc_busclk.[0-3]$" + - pattern: "^mmc_busclk.[0-3]$" + - pattern: "^mmc_busclk.[0-3]$" + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +allOf: + - $ref: mmc-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos4210-sdhci + then: + properties: + clocks: + maxItems: 2 + clock-names: + items: + - const: hsmmc + - const: mmc_busclk.2 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos4.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + mmc@12510000 { + compatible = "samsung,exynos4210-sdhci"; + reg = <0x12510000 0x100>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>; + clock-names = "hsmmc", "mmc_busclk.2"; + bus-width = <4>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; + pinctrl-names = "default"; + vmmc-supply = <&ldo21_reg>; + }; diff --git a/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt new file mode 100644 index 000000000..5f68feb9f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung,s3cmci.txt @@ -0,0 +1,42 @@ +* Samsung's S3C24XX MMC/SD/SDIO controller device tree bindings + +Samsung's S3C24XX MMC/SD/SDIO controller is used as a connectivity interface +with external MMC, SD and SDIO storage mediums. + +This file documents differences between the core mmc properties described by +mmc.txt and the properties used by the Samsung S3C24XX MMC/SD/SDIO controller +implementation. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c2410-sdi": for controllers compatible with s3c2410 + - "samsung,s3c2412-sdi": for controllers compatible with s3c2412 + - "samsung,s3c2440-sdi": for controllers compatible with s3c2440 +- reg: register location and length +- interrupts: mmc controller interrupt +- clocks: Should reference the controller clock +- clock-names: Should contain "sdi" + +Required Board Specific Properties: +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + +Optional Properties: +- bus-width: number of data lines (see mmc.txt) +- cd-gpios: gpio for card detection (see mmc.txt) +- wp-gpios: gpio for write protection (see mmc.txt) + +Example: + + mmc0: mmc@5a000000 { + compatible = "samsung,s3c2440-sdi"; + pinctrl-names = "default"; + pinctrl-0 = <&sdi_pins>; + reg = <0x5a000000 0x100000>; + interrupts = <0 0 21 3>; + clocks = <&clocks PCLK_SDI>; + clock-names = "sdi"; + bus-width = <4>; + cd-gpios = <&gpg 8 GPIO_ACTIVE_LOW>; + wp-gpios = <&gph 8 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml new file mode 100644 index 000000000..ea9121fb1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml @@ -0,0 +1,237 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mmc/sdhci-am654.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI AM654 MMC Controller + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + oneOf: + - const: ti,am654-sdhci-5.1 + - const: ti,j721e-sdhci-8bit + - const: ti,j721e-sdhci-4bit + - const: ti,am64-sdhci-8bit + - const: ti,am64-sdhci-4bit + - const: ti,am62-sdhci + - items: + - const: ti,j7200-sdhci-8bit + - const: ti,j721e-sdhci-8bit + - items: + - const: ti,j7200-sdhci-4bit + - const: ti,j721e-sdhci-4bit + + reg: + maxItems: 2 + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + description: Handles to input clocks + + clock-names: + minItems: 1 + items: + - const: clk_ahb + - const: clk_xin + + sdhci-caps-mask: true + + dma-coherent: + type: boolean + + # PHY output tap delays: + # Used to delay the data valid window and align it to the sampling clock. + # Binding needs to be provided for each supported speed mode otherwise the + # corresponding mode will be disabled. + + ti,otap-del-sel-legacy: + description: Output tap delay for SD/MMC legacy timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-mmc-hs: + description: Output tap delay for MMC high speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-sd-hs: + description: Output tap delay for SD high speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-sdr12: + description: Output tap delay for SD UHS SDR12 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-sdr25: + description: Output tap delay for SD UHS SDR25 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-sdr50: + description: Output tap delay for SD UHS SDR50 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-sdr104: + description: Output tap delay for SD UHS SDR104 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-ddr50: + description: Output tap delay for SD UHS DDR50 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-ddr52: + description: Output tap delay for eMMC DDR52 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-hs200: + description: Output tap delay for eMMC HS200 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,otap-del-sel-hs400: + description: Output tap delay for eMMC HS400 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + # PHY input tap delays: + # Used to delay the data valid window and align it to the sampling clock for + # modes that don't support tuning + + ti,itap-del-sel-legacy: + description: Input tap delay for SD/MMC legacy timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,itap-del-sel-mmc-hs: + description: Input tap delay for MMC high speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,itap-del-sel-sd-hs: + description: Input tap delay for SD high speed timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,itap-del-sel-sdr12: + description: Input tap delay for SD UHS SDR12 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,itap-del-sel-sdr25: + description: Input tap delay for SD UHS SDR25 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,itap-del-sel-ddr52: + description: Input tap delay for MMC DDR52 timing + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0x1f + + ti,trm-icp: + description: DLL trim select + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 0xf + + ti,driver-strength-ohm: + description: DLL drive strength in ohms + $ref: "/schemas/types.yaml#/definitions/uint32" + enum: + - 33 + - 40 + - 50 + - 66 + - 100 + + ti,strobe-sel: + description: strobe select delay for HS400 speed mode. + $ref: "/schemas/types.yaml#/definitions/uint32" + + ti,clkbuf-sel: + description: Clock Delay Buffer Select + $ref: "/schemas/types.yaml#/definitions/uint32" + + ti,fails-without-test-cd: + $ref: /schemas/types.yaml#/definitions/flag + description: + When present, indicates that the CD line is not connected + and the controller is required to be forced into Test mode + to set the TESTCD bit. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ti,otap-del-sel-legacy + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + mmc0: mmc@4f80000 { + compatible = "ti,am654-sdhci-5.1"; + reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>; + power-domains = <&k3_pds 47>; + clocks = <&k3_clks 47 0>, <&k3_clks 47 1>; + clock-names = "clk_ahb", "clk_xin"; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; + sdhci-caps-mask = <0x80000007 0x0>; + mmc-ddr-1_8v; + ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-mmc-hs = <0x0>; + ti,otap-del-sel-ddr52 = <0x5>; + ti,otap-del-sel-hs200 = <0x5>; + ti,otap-del-sel-hs400 = <0x0>; + ti,itap-del-sel-legacy = <0x10>; + ti,itap-del-sel-mmc-hs = <0xa>; + ti,itap-del-sel-ddr52 = <0x3>; + ti,trm-icp = <0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt new file mode 100644 index 000000000..69edfd4d3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt @@ -0,0 +1,33 @@ +* Atmel SDHCI controller + +This file documents the differences between the core properties in +Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the +sdhci-of-at91 driver. + +Required properties: +- compatible: Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci". +- clocks: Phandlers to the clocks. +- clock-names: Must be "hclock", "multclk", "baseclk" for + "atmel,sama5d2-sdhci". + Must be "hclock", "multclk" for "microchip,sam9x60-sdhci". + +Optional properties: +- assigned-clocks: The same with "multclk". +- assigned-clock-rates The rate of "multclk" in order to not rely on the + gck configuration set by previous components. +- microchip,sdcal-inverted: when present, polarity on the SDCAL SoC pin is + inverted. The default polarity for this signal is described in the datasheet. + For instance on SAMA5D2, the pin is usually tied to the GND with a resistor + and a capacitor (see "SDMMC I/O Calibration" chapter). + +Example: + +mmc0: sdio-host@a0000000 { + compatible = "atmel,sama5d2-sdhci"; + reg = <0xa0000000 0x300>; + interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>; + clock-names = "hclock", "multclk", "baseclk"; + assigned-clocks = <&sdmmc0_gclk>; + assigned-clock-rates = <480000000>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt new file mode 100644 index 000000000..3ee9263ad --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt @@ -0,0 +1,32 @@ +* Fujitsu SDHCI controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci_f_sdh30 driver. + +Required properties: +- compatible: "fujitsu,mb86s70-sdhci-3.0" +- clocks: Must contain an entry for each entry in clock-names. It is a + list of phandles and clock-specifier pairs. + See ../clocks/clock-bindings.txt for details. +- clock-names: Should contain the following two entries: + "iface" - clock used for sdhci interface + "core" - core clock for sdhci controller + +Optional properties: +- vqmmc-supply: phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host + requires the CMD_DAT_DELAY control to be enabled. + +Example: + + sdhci1: mmc@36600000 { + compatible = "fujitsu,mb86s70-sdhci-3.0"; + reg = <0 0x36600000 0x1000>; + interrupts = <0 172 0x4>, + <0 173 0x4>; + bus-width = <4>; + vqmmc-supply = <&vccq_sdhci1>; + clocks = <&clock 2 2 0>, <&clock 2 3 0>; + clock-names = "iface", "core"; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt new file mode 100644 index 000000000..627ee89c1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt @@ -0,0 +1,30 @@ +* SOCIONEXT Milbeaut SDHCI controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci_milbeaut driver. + +Required properties: +- compatible: "socionext,milbeaut-m10v-sdhci-3.0" +- clocks: Must contain an entry for each entry in clock-names. It is a + list of phandles and clock-specifier pairs. + See ../clocks/clock-bindings.txt for details. +- clock-names: Should contain the following two entries: + "iface" - clock used for sdhci interface + "core" - core clock for sdhci controller + +Optional properties: +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host + requires the CMD_DAT_DELAY control to be enabled. + +Example: + sdhci3: mmc@1b010000 { + compatible = "socionext,milbeaut-m10v-sdhci-3.0"; + reg = <0x1b010000 0x10000>; + interrupts = <0 265 0x4>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + clocks = <&clk 7>, <&ahb_clk>; + clock-names = "core", "iface"; + cap-sdio-irq; + fujitsu,cmd-dat-delay-select; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml b/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml new file mode 100644 index 000000000..eb0e9cca7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml @@ -0,0 +1,258 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/mmc/sdhci-msm.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Qualcomm SDHCI controller (sdhci-msm) + +maintainers: + - Bhupesh Sharma <bhupesh.sharma@linaro.org> + +description: + Secure Digital Host Controller Interface (SDHCI) present on + Qualcomm SOCs supports SD/MMC/SDIO devices. + +properties: + compatible: + oneOf: + - enum: + - qcom,sdhci-msm-v4 + deprecated: true + - items: + - enum: + - qcom,apq8084-sdhci + - qcom,msm8226-sdhci + - qcom,msm8953-sdhci + - qcom,msm8974-sdhci + - qcom,msm8916-sdhci + - qcom,msm8992-sdhci + - qcom,msm8994-sdhci + - qcom,msm8996-sdhci + - qcom,msm8998-sdhci + - const: qcom,sdhci-msm-v4 # for sdcc versions less than 5.0 + - items: + - enum: + - qcom,qcs404-sdhci + - qcom,sc7180-sdhci + - qcom,sc7280-sdhci + - qcom,sdm630-sdhci + - qcom,sdm670-sdhci + - qcom,sdm845-sdhci + - qcom,sdx55-sdhci + - qcom,sdx65-sdhci + - qcom,sm6115-sdhci + - qcom,sm6125-sdhci + - qcom,sm6350-sdhci + - qcom,sm8150-sdhci + - qcom,sm8250-sdhci + - qcom,sm8450-sdhci + - const: qcom,sdhci-msm-v5 # for sdcc version 5.0 + + reg: + minItems: 1 + maxItems: 4 + + reg-names: + minItems: 1 + maxItems: 4 + + clocks: + minItems: 2 + items: + - description: Main peripheral bus clock, PCLK/HCLK - AHB Bus clock + - description: SDC MMC clock, MCLK + - description: TCXO clock + - description: clock for Inline Crypto Engine + - description: SDCC bus voter clock + - description: reference clock for RCLK delay calibration + - description: sleep clock for RCLK delay calibration + + clock-names: + minItems: 2 + items: + - const: iface + - const: core + - const: xo + - const: ice + - const: bus + - const: cal + - const: sleep + + interrupts: + maxItems: 2 + + interrupt-names: + items: + - const: hc_irq + - const: pwr_irq + + pinctrl-names: + minItems: 1 + items: + - const: default + - const: sleep + + pinctrl-0: + description: + Should specify pin control groups used for this controller. + + pinctrl-1: + description: + Should specify sleep pin control groups used for this controller. + + resets: + maxItems: 1 + + qcom,ddr-config: + $ref: /schemas/types.yaml#/definitions/uint32 + description: platform specific settings for DDR_CONFIG reg. + + qcom,dll-config: + $ref: /schemas/types.yaml#/definitions/uint32 + description: platform specific settings for DLL_CONFIG reg. + + iommus: + minItems: 1 + maxItems: 8 + description: | + phandle to apps_smmu node with sid mask. + + interconnects: + items: + - description: data path, sdhc to ddr + - description: config path, cpu to sdhc + + interconnect-names: + items: + - const: sdhc-ddr + - const: cpu-sdhc + + power-domains: + description: A phandle to sdhci power domain node + maxItems: 1 + + mmc-ddr-1_8v: true + + mmc-hs200-1_8v: true + + mmc-hs400-1_8v: true + + bus-width: true + + max-frequency: true + + operating-points-v2: true + +patternProperties: + '^opp-table(-[a-z0-9]+)?$': + if: + properties: + compatible: + const: operating-points-v2 + then: + patternProperties: + '^opp-?[0-9]+$': + required: + - required-opps + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +allOf: + - $ref: mmc-controller.yaml# + + - if: + properties: + compatible: + contains: + enum: + - qcom,sdhci-msm-v4 + then: + properties: + reg: + minItems: 2 + items: + - description: Host controller register map + - description: SD Core register map + - description: CQE register map + - description: Inline Crypto Engine register map + reg-names: + minItems: 2 + items: + - const: hc + - const: core + - const: cqhci + - const: ice + else: + properties: + reg: + minItems: 1 + items: + - description: Host controller register map + - description: CQE register map + - description: Inline Crypto Engine register map + reg-names: + minItems: 1 + items: + - const: hc + - const: cqhci + - const: ice + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sm8250.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + sdhc_2: mmc@8804000 { + compatible = "qcom,sm8250-sdhci", "qcom,sdhci-msm-v5"; + reg = <0 0x08804000 0 0x1000>; + + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "core", "xo"; + iommus = <&apps_smmu 0x4a0 0x0>; + qcom,dll-config = <0x0007642c>; + qcom,ddr-config = <0x80040868>; + power-domains = <&rpmhpd SM8250_CX>; + + operating-points-v2 = <&sdhc2_opp_table>; + + sdhc2_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-19200000 { + opp-hz = /bits/ 64 <19200000>; + required-opps = <&rpmhpd_opp_min_svs>; + }; + + opp-50000000 { + opp-hz = /bits/ 64 <50000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-202000000 { + opp-hz = /bits/ 64 <202000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt new file mode 100644 index 000000000..f91e341e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -0,0 +1,43 @@ +* TI OMAP SDHCI Controller + +Refer to mmc.txt for standard MMC bindings. + +For UHS devices which require tuning, the device tree should have a "cpu_thermal" node which maps to the appropriate thermal zone. This is used to get the temperature of the zone during tuning. + +Required properties: +- compatible: Should be "ti,omap2430-sdhci" for omap2430 controllers + Should be "ti,omap3-sdhci" for omap3 controllers + Should be "ti,omap4-sdhci" for omap4 and ti81 controllers + Should be "ti,omap5-sdhci" for omap5 controllers + Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers + Should be "ti,k2g-sdhci" for K2G + Should be "ti,am335-sdhci" for am335x controllers + Should be "ti,am437-sdhci" for am437x controllers +- ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + (Not required for K2G). +- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50", + "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104", + "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11", + "hs200_1_8v", +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt + +Optional properties: +- dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. A tx and rx specifier is required. +- dma-names: List of DMA request names. These strings correspond 1:1 with the + DMA specifiers listed in dmas. The string naming is to be "tx" + and "rx" for TX and RX DMA requests, respectively. + +Deprecated properties: +- ti,non-removable: Compatible with the generic non-removable property + +Example: + mmc1: mmc@4809c000 { + compatible = "ti,dra7-sdhci"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + dmas = <&sdma 61 &sdma 62>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml new file mode 100644 index 000000000..1c87f4218 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/sdhci-pxa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell PXA SDHCI v2/v3 bindings + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +allOf: + - $ref: mmc-controller.yaml# + - if: + properties: + compatible: + contains: + const: marvell,armada-380-sdhci + then: + properties: + regs: + minItems: 3 + reg-names: + minItems: 3 + required: + - reg-names + else: + properties: + regs: + maxItems: 1 + reg-names: + maxItems: 1 + +properties: + compatible: + enum: + - mrvl,pxav2-mmc + - mrvl,pxav3-mmc + - marvell,armada-380-sdhci + + reg: + minItems: 1 + maxItems: 3 + + reg-names: + items: + - const: sdhci + - const: mbus + - const: conf-sdio3 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: io + - const: core + + mrvl,clk-delay-cycles: + description: Specify a number of cycles to delay for tuning. + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/berlin2.h> + mmc@d4280800 { + compatible = "mrvl,pxav3-mmc"; + reg = <0xd4280800 0x800>; + bus-width = <8>; + interrupts = <27>; + clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>; + clock-names = "io", "core"; + non-removable; + mrvl,clk-delay-cycles = <31>; + }; + - | + mmc@d8000 { + compatible = "marvell,armada-380-sdhci"; + reg-names = "sdhci", "mbus", "conf-sdio3"; + reg = <0xd8000 0x1000>, + <0xdc000 0x100>, + <0x18454 0x4>; + interrupts = <0 25 0x4>; + clocks = <&gateclk 17>; + clock-names = "io"; + mrvl,clk-delay-cycles = <0x1F>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt new file mode 100644 index 000000000..fd3643e7e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt @@ -0,0 +1,18 @@ +* SPEAr SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-spear driver. + +Required properties: +- compatible: "st,spear300-sdhci" + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sdhci@fc000000 { + compatible = "st,spear300-sdhci"; + reg = <0xfc000000 0x1000>; + cd-gpios = <&gpio0 6 0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt new file mode 100644 index 000000000..eb7eb1b52 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt @@ -0,0 +1,67 @@ +* Spreadtrum SDHCI controller (sdhci-sprd) + +The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface +for MMC, SD and SDIO types of cards. + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-sprd driver. + +Required properties: +- compatible: Should contain "sprd,sdhci-r11". +- reg: physical base address of the controller and length. +- interrupts: Interrupts used by the SDHCI controller. +- clocks: Should contain phandle for the clock feeding the SDHCI controller +- clock-names: Should contain the following: + "sdio" - SDIO source clock (required) + "enable" - gate clock which used for enabling/disabling the device (required) + "2x_enable" - gate clock controlling the device for some special platforms (optional) + +Optional properties: +- assigned-clocks: the same with "sdio" clock +- assigned-clock-parents: the default parent of "sdio" clock +- pinctrl-names: should be "default", "state_uhs" +- pinctrl-0: should contain default/high speed pin control +- pinctrl-1: should contain uhs mode pin control + +PHY DLL delays are used to delay the data valid window, and align the window +to sampling clock. PHY DLL delays can be configured by following properties, +and each property contains 4 cells which are used to configure the clock data +write line delay value, clock read command line delay value, clock read data +positive edge delay value and clock read data negative edge delay value. +Each cell's delay value unit is cycle of the PHY clock. + +- sprd,phy-delay-legacy: Delay value for legacy timing. +- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing. +- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing. +- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing. +- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing. +- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing. +- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing. +- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing. +- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing. + +Examples: + +sdio0: sdio@20600000 { + compatible = "sprd,sdhci-r11"; + reg = <0 0x20600000 0 0x1000>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + + clock-names = "sdio", "enable"; + clocks = <&ap_clk CLK_EMMC_2X>, + <&apahb_gate CLK_EMMC_EB>; + assigned-clocks = <&ap_clk CLK_EMMC_2X>; + assigned-clock-parents = <&rpll CLK_RPLL_390M>; + + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&sd0_pins_default>; + pinctrl-1 = <&sd0_pins_uhs>; + + sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>; + bus-width = <8>; + non-removable; + no-sdio; + no-sd; + cap-mmc-hw-reset; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt new file mode 100644 index 000000000..ccf82b4ee --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -0,0 +1,110 @@ +* STMicroelectronics sdhci-st MMC/SD controller + +This file documents the differences between the core properties in +Documentation/devicetree/bindings/mmc/mmc.txt and the properties +used by the sdhci-st driver. + +Required properties: +- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407" + to set the internal glue logic used for configuring the MMC + subsystem (mmcss) inside the FlashSS (available in STiH407 SoC + family). + +- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- interrupts: One mmc interrupt should be described here. +- interrupt-names: Should be "mmcirq". + +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +- reg: This must provide the host controller base address and it can also + contain the FlashSS Top register for TX/RX delay used by the driver + to configure DLL inside the flashSS, if so reg-names must also be + specified. + +Optional properties: +- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional + for eMMC on stih407 family silicon to configure DLL inside FlashSS. + +- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC + family. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- bus-width: Number of data lines. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- max-frequency: Can be 200MHz, 100MHz or 50MHz (default) and used for + configuring the CCONFIG3 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- resets: Phandle and reset specifier pair to softreset line of HC IP. + See: Documentation/devicetree/bindings/reset/reset.txt + +- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd + supply in eMMC/SD specs. + +- sd-uhs-sdr50: To enable the SDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-sdr104: To enable the SDR104 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-ddr50: To enable the DDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +Example: + +/* Example stih416e eMMC configuration */ + +mmc0: sdhci@fe81e000 { + compatible = "st,sdhci"; + reg = <0xfe81e000 0x1000>; + interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_a1_ls 1>; + bus-width = <8> + +/* Example SD stih407 family configuration */ + +mmc1: sdhci@9080000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + reg = <0x09080000 0x7ff>; + reg-names = "mmc"; + interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd1>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_1>; + resets = <&softreset STIH407_MMC1_SOFTRESET>; + bus-width = <4>; +}; + +/* Example eMMC stih407 family configuration */ + +mmc0: sdhci@9060000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + reg = <0x09060000 0x7ff>, <0x9061008 0x20>; + reg-names = "mmc", "top-mmc-delay"; + interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_0>; + vqmmc-supply = <&vmmc_reg>; + max-frequency = <200000000>; + bus-width = <8>; + non-removable; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci.txt b/Documentation/devicetree/bindings/mmc/sdhci.txt new file mode 100644 index 000000000..0e9923a64 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci.txt @@ -0,0 +1,13 @@ +The properties specific for SD host controllers. For properties shared by MMC +host controllers refer to the mmc[1] bindings. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Optional properties: +- sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the bit + is on in the mask then the bit is incorrect in the register and should be + turned off, before applying sdhci-caps. +- sdhci-caps: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the + bit is on in the property then the bit should be turned on. diff --git a/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml b/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml new file mode 100644 index 000000000..71f8e726d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/snps,dwcmshc-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys Designware Mobile Storage Host Controller Binding + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + - Jisheng Zhang <Jisheng.Zhang@synaptics.com> + +allOf: + - $ref: mmc-controller.yaml# + +properties: + compatible: + enum: + - rockchip,rk3568-dwcmshc + - rockchip,rk3588-dwcmshc + - snps,dwcmshc-sdhci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: core clock + - description: bus clock for optional + - description: axi clock for rockchip specified + - description: block clock for rockchip specified + - description: timer clock for rockchip specified + + + clock-names: + minItems: 1 + items: + - const: core + - const: bus + - const: axi + - const: block + - const: timer + + rockchip,txclk-tapnum: + description: Specify the number of delay for tx sampling. + $ref: /schemas/types.yaml#/definitions/uint8 + + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + mmc@fe310000 { + compatible = "rockchip,rk3568-dwcmshc"; + reg = <0xfe310000 0x10000>; + interrupts = <0 25 0x4>; + clocks = <&cru 17>, <&cru 18>, <&cru 19>, <&cru 20>, <&cru 21>; + clock-names = "core", "bus", "axi", "block", "timer"; + bus-width = <8>; + #address-cells = <1>; + #size-cells = <0>; + }; + - | + mmc@aa0000 { + compatible = "snps,dwcmshc-sdhci"; + reg = <0xaa000 0x1000>; + interrupts = <0 25 0x4>; + clocks = <&cru 17>, <&cru 18>; + clock-names = "core", "bus"; + bus-width = <8>; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/socionext,uniphier-sd.yaml b/Documentation/devicetree/bindings/mmc/socionext,uniphier-sd.yaml new file mode 100644 index 000000000..a586fad0a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/socionext,uniphier-sd.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/socionext,uniphier-sd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier SD/SDIO/eMMC controller + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +properties: + compatible: + description: version 2.91, 3.1, 3.1.1, respectively + enum: + - socionext,uniphier-sd-v2.91 + - socionext,uniphier-sd-v3.1 + - socionext,uniphier-sd-v3.1.1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + + reset-names: + description: | + There are three reset signals at maximum + host: mandatory for all variants + bridge: exist only for version 2.91 + hw: optional. exist if eMMC hw reset line is available + oneOf: + - const: host + - items: + - const: host + - const: bridge + - items: + - const: host + - const: hw + - items: + - const: host + - const: bridge + - const: hw + + resets: + minItems: 1 + maxItems: 3 + +allOf: + - $ref: mmc-controller.yaml + + - if: + properties: + compatible: + contains: + const: socionext,uniphier-sd-v2.91 + then: + properties: + reset-names: + contains: + const: bridge + else: + properties: + reset-names: + not: + contains: + const: bridge + +required: + - compatible + - reg + - interrupts + - clocks + - reset-names + - resets + +unevaluatedProperties: false + +examples: + - | + sd: mmc@5a400000 { + compatible = "socionext,uniphier-sd-v2.91"; + reg = <0x5a400000 0x200>; + interrupts = <0 76 4>; + pinctrl-names = "default", "uhs"; + pinctrl-0 = <&pinctrl_sd>; + pinctrl-1 = <&pinctrl_sd_uhs>; + clocks = <&mio_clk 0>; + reset-names = "host", "bridge"; + resets = <&mio_rst 0>, <&mio_rst 3>; + dma-names = "rx-tx"; + dmas = <&dmac 4>; + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml new file mode 100644 index 000000000..8dfad89c7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/synopsys-dw-mshc-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys Designware Mobile Storage Host Controller Common Properties + +allOf: + - $ref: "mmc-controller.yaml#" + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +# Everything else is described in the common file +properties: + resets: + maxItems: 1 + + reset-names: + const: reset + + clock-frequency: + description: + Should be the frequency (in Hz) of the ciu clock. If this + is specified and the ciu clock is specified then we'll try to set the ciu + clock to this at probe time. + + fifo-depth: + description: + The maximum size of the tx/rx fifo's. If this property is not + specified, the default value of the fifo size is determined from the + controller registers. + $ref: /schemas/types.yaml#/definitions/uint32 + + card-detect-delay: + description: + Delay in milli-seconds before detecting card after card + insert event. The default value is 0. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + data-addr: + description: + Override fifo address with value provided by DT. The default FIFO reg + offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) + by driver. If the controller does not follow this rule, please use + this property to set fifo address in device tree. + $ref: /schemas/types.yaml#/definitions/uint32 + + fifo-watermark-aligned: + description: + Data done irq is expected if data length is less than + watermark in PIO mode. But fifo watermark is requested to be aligned + with data length in some SoC so that TX/RX irq can be generated with + data done irq. Add this watermark quirk to mark this requirement and + force fifo watermark setting accordingly. + $ref: /schemas/types.yaml#/definitions/flag + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml new file mode 100644 index 000000000..ae6d6fca7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/synopsys-dw-mshc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys Designware Mobile Storage Host Controller Binding + +allOf: + - $ref: "synopsys-dw-mshc-common.yaml#" + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +# Everything else is described in the common file +properties: + compatible: + enum: + - altr,socfpga-dw-mshc + - img,pistachio-dw-mshc + - snps,dw-mshc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 2 + description: + Handle to "biu" and "ciu" clocks for the + bus interface unit clock and the card interface unit clock. + + clock-names: + items: + - const: biu + - const: ciu + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + mmc@12200000 { + compatible = "snps,dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + clocks = <&clock 351>, <&clock 132>; + clock-names = "biu", "ciu"; + dmas = <&pdma 12>; + dma-names = "rx-tx"; + resets = <&rst 20>; + reset-names = "reset"; + vmmc-supply = <&buck8>; + #address-cells = <1>; + #size-cells = <0>; + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + max-frequency = <200000000>; + clock-frequency = <400000000>; + data-addr = <0x200>; + fifo-depth = <0x80>; + fifo-watermark-aligned; + }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt new file mode 100644 index 000000000..57d077c0b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -0,0 +1,134 @@ +* TI Highspeed MMC host controller for OMAP and 66AK2G family. + +The Highspeed MMC Host Controller on TI OMAP and 66AK2G family +provides an interface for MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap_hsmmc driver. + +Required properties: +-------------------- +- compatible: + Should be "ti,omap2-hsmmc", for OMAP2 controllers + Should be "ti,omap3-hsmmc", for OMAP3 controllers + Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0 + Should be "ti,omap4-hsmmc", for OMAP4 controllers + Should be "ti,am33xx-hsmmc", for AM335x controllers + Should be "ti,k2g-hsmmc", "ti,omap4-hsmmc" for 66AK2G controllers. + +SoC specific required properties: +--------------------------------- +The following are mandatory properties for OMAPs, AM33xx and AM43xx SoCs only: +- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the MMC device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.yaml +- clocks: Must contain an entry for each entry in clock-names. Should + be defined as per the he appropriate clock bindings consumer + usage in Documentation/devicetree/bindings/clock/ti,sci-clk.yaml +- clock-names: Shall be "fck" for the functional clock, + and "mmchsdb_fck" for the debounce clock. + + +Optional properties: +-------------------- +- ti,dual-volt: boolean, supports dual voltage cards +- <supply-name>-supply: phandle to the regulator device tree node + "supply-name" examples are "vmmc", + "vmmc_aux"(deprecated)/"vqmmc" etc +- ti,non-removable: non-removable slot (like eMMC) +- ti,needs-special-reset: Requires a special softreset sequence +- ti,needs-special-hs-handling: HSMMC IP needs special setting + for handling High Speed +- dmas: List of DMA specifiers with the controller specific + format as described in the generic DMA client + binding. A tx and rx specifier is required. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. + The string naming is to be "rx" and "tx" for + RX and TX DMA requests, respectively. + +Examples: + +[hwmod populated DMA resources] + + mmc1: mmc@4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + ti,dual-volt; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + ti,non-removable; + }; + +[generic DMA request binding] + + mmc1: mmc@4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + ti,dual-volt; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + ti,non-removable; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + }; + +[workaround for missing swakeup on am33xx] + +This SOC is missing the swakeup line, it will not detect SDIO irq +while in suspend. + + ------ + | PRCM | + ------ + ^ | + swakeup | | fclk + | v + ------ ------- ----- + | card | -- CIRQ --> | hsmmc | -- IRQ --> | CPU | + ------ ------- ----- + +In suspend the fclk is off and the module is disfunctional. Even register reads +will fail. A small logic in the host will request fclk restore, when an +external event is detected. Once the clock is restored, the host detects the +event normally. Since am33xx doesn't have this line it never wakes from +suspend. + +The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make +this work, we need to set the named pinctrl states "default" and "idle". +Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio +dat1. The MMC driver will then toggle between idle and default state during +runtime. + +In summary: +1. select matching 'compatible' section, see example below. +2. specify pinctrl states "default" and "idle", "sleep" is optional. +3. specify the gpio irq used for detecting sdio irq in suspend + +If configuration is incomplete, a warning message is emitted "falling back to +polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind +not every application needs SDIO irq, e.g. MMC cards. + + mmc1: mmc@48060100 { + compatible = "ti,am33xx-hsmmc"; + ... + pinctrl-names = "default", "idle", "sleep" + pinctrl-0 = <&mmc1_pins>; + pinctrl-1 = <&mmc1_idle>; + pinctrl-2 = <&mmc1_sleep>; + ... + interrupts-extended = <&intc 64 &gpio2 28 IRQ_TYPE_LEVEL_LOW>; + }; + + mmc1_idle : pinmux_cirq_pin { + pinctrl-single,pins = < + 0x0f8 0x3f /* GPIO2_28 */ + >; + }; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap.txt b/Documentation/devicetree/bindings/mmc/ti-omap.txt new file mode 100644 index 000000000..02fd31cf3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/ti-omap.txt @@ -0,0 +1,26 @@ +* TI MMC host controller for OMAP1 and 2420 + +The MMC Host Controller on TI OMAP1 and 2420 family provides +an interface for MMC, SD, and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the omap mmc driver. + +Note that this driver will not work with omap2430 or later omaps, +please see the omap hsmmc driver for the current omaps. + +Required properties: +- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers +- ti,hwmods: For 2420, must be "msdi<n>", where n is controller + instance starting 1 + +Examples: + + msdi1: mmc@4809c000 { + compatible = "ti,omap2420-mmc"; + ti,hwmods = "msdi1"; + reg = <0x4809c000 0x80>; + interrupts = <83>; + dmas = <&sdma 61 &sdma 62>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt new file mode 100644 index 000000000..6d1b7971d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt @@ -0,0 +1,39 @@ +* Renesas usdhi6rol0 SD/SDIO host controller + +Required properties: + +- compatible: must be + "renesas,usdhi6rol0" +- interrupts: 3 interrupts, named "card detect", "data" and "SDIO" must be + specified +- clocks: a clock binding for the IMCLK input + +Optional properties: + +- vmmc-supply: a phandle of a regulator, supplying Vcc to the card +- vqmmc-supply: a phandle of a regulator, supplying VccQ to the card +- pinctrl-names: Can contain a "default" entry and a "state_uhs" + entry. The state_uhs entry is used together with the default + entry when the board requires distinct settings for UHS speeds. + +- pinctrl-N: One property for each name listed in pinctrl-names, see + ../pinctrl/pinctrl-bindings.txt. + +Additionally any standard mmc bindings from mmc.txt can be used. + +Example: + +sd0: sd@ab000000 { + compatible = "renesas,usdhi6rol0"; + reg = <0xab000000 0x200>; + interrupts = <0 23 0x4 + 0 24 0x4 + 0 25 0x4>; + interrupt-names = "card detect", "data", "SDIO"; + bus-width = <4>; + max-frequency = <50000000>; + cap-power-off-card; + clocks = <&imclk>; + vmmc-supply = <&vcc_sd0>; + vqmmc-supply = <&vccq_sd0>; +}; diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt new file mode 100644 index 000000000..d7fb6abb3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt @@ -0,0 +1,23 @@ +* Wondermedia WM8505/WM8650 SD/MMC Host Controller + +This file documents differences between the core properties described +by mmc.txt and the properties used by the wmt-sdmmc driver. + +Required properties: +- compatible: Should be "wm,wm8505-sdhc". +- interrupts: Two interrupts are required - regular irq and dma irq. + +Optional properties: +- sdon-inverted: SD_ON bit is inverted on the controller + +Examples: + +sdhc@d800a000 { + compatible = "wm,wm8505-sdhc"; + reg = <0xd800a000 0x1000>; + interrupts = <20 21>; + clocks = <&sdhc>; + bus-width = <4>; + sdon-inverted; +}; + |