diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml | 156 |
1 files changed, 156 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml new file mode 100644 index 000000000..445b2a553 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml @@ -0,0 +1,156 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Bluetooth Chips + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + This binding describes Broadcom UART-attached bluetooth chips. + +properties: + compatible: + enum: + - brcm,bcm20702a1 + - brcm,bcm4329-bt + - brcm,bcm4330-bt + - brcm,bcm4334-bt + - brcm,bcm43438-bt + - brcm,bcm4345c5 + - brcm,bcm43540-bt + - brcm,bcm4335a0 + - brcm,bcm4349-bt + - infineon,cyw55572-bt + + shutdown-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_REG_ON used to + power on the BT module + + reset-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_RST_N used to + reset the BT module. This should be marked as + GPIO_ACTIVE_LOW. + + device-wakeup-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_WAKE used to + wakeup the controller. This is using the BT_GPIO_0 + pin on the chip when in use. + + host-wakeup-gpios: + maxItems: 1 + deprecated: true + description: GPIO specifier for the line HOST_WAKE used + to wakeup the host processor. This is using he BT_GPIO_1 + pin on the chip when in use. This is deprecated and replaced + by interrupts and "host-wakeup" interrupt-names + + clocks: + minItems: 1 + maxItems: 2 + description: 1 or 2 clocks as defined in clock-names below, + in that order + + clock-names: + description: Names of the 1 to 2 supplied clocks + oneOf: + - const: extclk + deprecated: true + description: Deprecated in favor of txco + + - const: txco + description: > + external reference clock (not a standalone crystal) + + - const: lpo + description: > + external low power 32.768 kHz clock + + - items: + - const: txco + - const: lpo + + vbat-supply: + description: phandle to regulator supply for VBAT + + vddio-supply: + description: phandle to regulator supply for VDDIO + + brcm,bt-pcm-int-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 5 + maxItems: 5 + description: |- + configure PCM parameters via a 5-byte array: + sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S + pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps + pcm-frame-type: short, long + pcm-sync-mode: slave, master + pcm-clock-mode: slave, master + + brcm,requires-autobaud-mode: + type: boolean + description: + Set this property if autobaud mode is required. Autobaud mode is required + if the device's initial baud rate in normal mode is not supported by the + host or if the device requires autobaud mode startup before loading FW. + + interrupts: + items: + - description: Handle to the line HOST_WAKE used to wake + up the host processor. This uses the BT_GPIO_1 pin on + the chip when in use. + + interrupt-names: + items: + - const: host-wakeup + + max-speed: true + current-speed: true + +required: + - compatible + +dependencies: + brcm,requires-autobaud-mode: [ 'shutdown-gpios' ] + +if: + not: + properties: + compatible: + contains: + enum: + - brcm,bcm20702a1 + - brcm,bcm4329-bt + - brcm,bcm4330-bt +then: + properties: + reset-gpios: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + uart { + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + max-speed = <921600>; + brcm,bt-pcm-int-params = [01 02 00 01 01]; + shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + }; + }; |